PI5C6800QEX [PERICOM]

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.150 INCH, GREEN, QSOP-24;
PI5C6800QEX
型号: PI5C6800QEX
厂家: PERICOM SEMICONDUCTOR CORPORATION    PERICOM SEMICONDUCTOR CORPORATION
描述:

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.150 INCH, GREEN, QSOP-24

驱动 光电二极管 逻辑集成电路
文件: 总5页 (文件大小:388K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
PI5C6800  
10-Bit Bus Switch with  
Precharged Outputs  
Features  
• Near-Zero propagation delay  
Description  
Pericom’s Semiconductor’s PI5C6800 is a 10-bit bus switch with  
low On-State resistance. The bus switch creates no additional  
propagation delay.  
• 5Ω switch connection between two ports  
• Ultra-low quiescent power (0.2μA typical)  
• Ideally suited for notebook applications  
• A port is hot swapable  
The switch is turned on by a single enable (ON) input. When ON  
is LOW, the switch is on and port A is connnected to port B. When  
ON is HIGH, the switch between port A and port B is open and  
the B port is precharged to BIASV through the equivalent of a  
10k-ohm resistor.  
• Packaging (Pb-free & Green available):  
– 24-pin 150-mil wide QSOP (Q)  
– 24-pin 173-mil wide TSSOP (L)  
Pin Conguration  
Block Diagram  
13  
23  
ON  
1
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
14  
13  
V
B
B
B
B
B
B
B
B
B
B
CC  
1
A
2
1
3
A
A
A
A
A
A
A
A
2
3
4
5
6
7
8
9
2
B1  
A1  
4
3
5
4
6
5
7
6
14  
A10  
B10  
8
7
9
8
10  
11  
12  
9
A
10  
10  
ON  
GND  
BIASV  
(1)  
Truth Table  
Function  
ON  
L
B1 - B10  
A1- A10  
BIASV  
Connect  
Precharge  
H
Notes:  
1. H = High Voltage Level, L = Low Voltage Level  
PS8194I  
03/26/07  
06-0229  
1
PI5C6800  
10-Bit Bus Switch with  
Precharged Outputs  
(1)  
Absolute Maximum Ratings Over Free-Air Temperature Range  
(Above which the useful life may be impaired. For user guidelines, not tested.)  
Storage Temperature .....................................................–65°C to +150°C  
Supply Voltage Range.........................................................–0.5V to +7V  
(2)  
DC Input Voltage .............................................................–0.5V to +7V  
Input Clamp Current, I (V <0)..................................................50mA  
IK  
1
DC Output Current........................................................................120mA  
(3)  
Power Dissipation ........................................................................0.5W  
Notes:  
1. Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and  
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specication is not  
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.  
2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.  
3. The maximum package power dissipation is calculated using a junction temperatue of 150°C and a board trace length of 750 mils.  
Recommended Operating Conditions  
Parameters  
Description  
Min.  
Typ.  
Units  
V
V
Supply Voltage  
4
0
2
5.5  
CC  
BIASV  
Supply Voltage  
V
CC  
V
High-level input voltage  
Low-level input voltage  
Operating free-air voltage  
IH  
V
0.8  
85  
IL  
T
A
–40  
°C  
Electrical Characteristics (Over Recommended Operating Free-air Temperature Range)  
(2)  
Parameters  
Test Condidtion  
Min.  
Typ.  
Max.  
Units  
V
V
V
V
V
V
= 4.5V, I = 18mA  
–1.2  
±5  
IK  
CC  
CC  
CC  
CC  
I
I
= 5.5V, V = 5.5V or GND  
μA  
I
I
I
= 4.5V, BIASV = 2.4V, V = 0  
–0.20  
mA  
mA  
O
O
I
CC  
=5.5V, I = 0, V = V or GND  
3
O
I
CC  
C
V = 3V or 0  
3.5  
4.5  
14  
5
IN  
I
pF  
C
V = 3V or 0, Switch Off  
O
OFF  
V
V
= 4V  
V = 2.4V, I = 15mA  
22  
7
CC  
CC  
I
I
V = 0V, I = 64mA  
I
I
(1)  
ON  
R
Ω
= 4.5V  
V = 0V, I = 30mA  
5
7
I
I
V = 2.4V, I = 15mA  
10  
15  
I
I
Notes:  
1. Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-State resistance is determined by  
the lower of the voltages of the two (A or B) terminals.  
2. All typical values are at VCC = 5V, TA = 25°C.  
PS8194I  
03/26/07  
06-0229  
2
PI5C6800  
10-Bit Bus Switch with  
Precharged Outputs  
Switching Characteristics (Over Recommended Operating Free-air Temperature Range, C = 50pF)  
L
V
= 5V ±0.5V  
V
= 4V  
CC  
CC  
Parameter  
Test Conditions From (Input)  
To (Input)  
B or A  
Units  
Min.  
Max.  
Min.  
Max.  
(1)  
t
A or B  
0.25  
0.25  
6
PD  
t
BIASV = GND  
ON  
3.1  
3.6  
2.7  
3
5
5
5
5
PZH  
A or B  
t
BIASV = 3V  
6
ns  
PZL  
t
BIAS = GND  
ON  
5.5  
5.5  
PHZ  
A or B  
t
BIAS = 3V  
PLZ  
Notes:  
1. This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical On-State resis-  
tance of the switch and a load capacitance of 50pF, when driven by an ideal voltage source (zero output impedance).  
Parameter Measurements  
7V  
Test  
S1  
S1  
Open  
GND  
500Ω  
t
Open  
7V  
From Output  
Under Test  
PD  
t
/t  
PLZ PZL  
CL = 50pF  
t
/t  
Open  
PHZ PZH  
500Ω  
3V  
Output  
Control  
(Low Level  
Enabling)  
LOAD CIRCUIT  
1.5V  
1.5V  
0V  
t
PZL  
tPLZ  
3V  
0V  
Output  
Waveform 1  
S1 at 6V  
3.5V  
1.5V  
1.5V  
Input  
1.5V  
1.5V  
V
OL +0.3V  
V
OL  
tPLH  
tPZH  
tPHL  
t
PHZ  
Output  
Waveform 2  
S1 at Open  
V
OH  
VOH  
VOL  
V
OH -0.3V  
1.5V  
1.5V  
Output  
0V  
VOLTAGE WAVEFORMS  
ENABLE AND DISABLE TIMES  
VOLTAGE WAVEFORMS  
PROPAGATION DELAY TIMES  
Notes:  
• CL includes probe and jig capacitance.  
• Waveform 1 is for an output with internal conditions such that the output is LOW except when disabled by the output control.  
• Waveform 2 is for an output with internal conditions such that the output is HIGH except when disabled by the output control.  
• All input pulses are supplied by generators having the following characteristics: PRR < 10MHz, ZO = 50, tr 2.5ns, tf 2.5ns.  
• The outputs are measured one at a time with one transition per measurement.  
• tPLZ and tPHZ are the same as tdis  
.
• tPZL and tPZH are the same as ten.  
• tPLH and tPHL are the same as tpd  
.
PS8194I  
03/26/07  
06-0229  
3
PI5C6800  
10-Bit Bus Switch with  
Precharged Outputs  
Applications Information  
Logic Inputs  
The logic control inputs can be driven up to +5.5V regardless of the supply voltage. For example, given a +5.0V supply, control  
®
inputs may be driven low to 0V and high to 5.5V. Driving control inputs Rail-to-Rail minimizes power consumption.  
Power-Supply Sequencing  
Proper power-supply sequencing is recommended for all CMOS devices. Always apply V before applying signals to the input/  
CC  
output or control pins.  
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.  
Packaging Mechanical: 24-pin QSOP (Q)  
24  
.008  
0.20  
MIN.  
.008  
.013  
0.20  
0.33  
.150  
.157  
3.81  
3.99  
Guage Plane  
0˚-6˚  
.010  
.016  
.035  
0.41  
0.89  
0.254  
Detail A  
1
.041  
1.04  
REF  
.337 8.56  
.344 8.74  
.015 x 45˚  
0.38  
.033  
0.84  
.053 1.35  
.069 1.75  
Detail A  
0.178  
0.254  
.007  
.010  
SEATING  
PLANE  
.016 0.406  
.050 1.27  
0.101  
0.254  
.004  
.010  
.025  
typical  
.228  
.244  
0.203  
0.305  
.008  
.012  
0.635  
5.79  
6.20  
X.XX  
X.XX  
DENOTES DIMENSIONS  
IN MILLIMETERS  
PS8194I  
03/26/07  
06-0229  
4
PI5C6800  
10-Bit Bus Switch with  
Precharged Outputs  
Packaging Mechanical: 24-pin TSSOP (L)  
24  
.169  
.177  
4.3  
4.5  
.0075  
.0098  
0.19  
0.25  
0.45 .018  
0.75 .030  
1
.303 7.7  
.311 7.9  
.252  
BSC  
.047  
Max  
1.20  
6.4  
SEATING  
PLANE  
.002 0.05  
.006 0.15  
.007  
.012  
.0255  
BSC  
0.19  
0.30  
0.65  
Ordering Information  
Ordering Code  
PI5C6800L  
Package Code  
Package Description  
L
L
24-Pin 173-mil TSSOP  
PI5C6800LE  
Pb-free & Green, 24-Pin 173-mil TSSOP  
24-Pin 150-mil QSOP  
PI5C6800Q  
Q
Q
PI5C6800QE  
Pb-free & Green, 24-Pin 150-mil QSOP  
Notes:  
Thermal characteristics can be found on the company web site at www.pericom.com/packaging/  
E = Pb-free & Green  
• Adding an X sufx = Tape/Reel  
Pericom Semiconductor Corporation 1-800-435-2336 • www.pericom.com  
PS8194I  
03/26/07  
06-0229  
5

相关型号:

PI5C6800QX

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.150 INCH, QSOP-24
PERICOM

PI5C6801C

10-Bit Bus Switch with Precharged Outputs for Live Insertion and - 2V Undershoot Protection
PERICOM

PI5C6801CL

10-Bit Bus Switch with Precharged Outputs for Live Insertion and - 2V Undershoot Protection
PERICOM

PI5C6801CQ

10-Bit Bus Switch with Precharged Outputs for Live Insertion and - 2V Undershoot Protection
PERICOM

PI5C6900CDLX

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.173 INCH, PLASTIC, TSSOP-24
PERICOM

PI5C6900CDQ

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.150 INCH, PLASTIC, QSOP-24
PERICOM

PI5C6900CDQX

Bus Driver, CBT/FST/QS/5C/B Series, 1-Func, 10-Bit, True Output, CMOS, PDSO24, 0.150 INCH, PLASTIC, QSOP-24
PERICOM

PI5L100

Wide Bandwidth Low Voltage LanSwitch Quad 2:1 Mux/Demux
PERICOM

PI5L100L

Wide Bandwidth Low Voltage LanSwitch Quad 2:1 Mux/Demux
PERICOM

PI5L100LE

Wide Bandwidth Low Voltage LanSwitch Quad 2:1 Mux/Demux
PERICOM

PI5L100LEX

Bus Exchanger, 5L Series, 1-Func, 2-Bit, True Output, CMOS, PDSO20, 0.173 INCH, PLASTIC, TSSOP-20
PERICOM

PI5L100Q

Wide Bandwidth Low Voltage LanSwitch Quad 2:1 Mux/Demux
PERICOM