PI5PD2560 [PERICOM]
Dual Channel, Adjustable Current -Limited Power Switch;
| 型号： | PI5PD2560 |
| 厂家： | 
PERICOM SEMICONDUCTOR CORPORATION |
| 描述： | Dual Channel, Adjustable Current -Limited Power Switch |
| 文件： | 总12页 (文件大小：786K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PI5PD2560/2561
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Dual Channel, Adjustable Current -Limited Power Switch
Features
Description
Two separate current limiting channels
Meets USB Current-Limiting Requirement
±7.5% Current-Limit Accuracy at 2.8A
Adjustable Current Limit, 250mA-2.8A (typ)
Fast Over-current Response - 3.5μS (typ)
44mΩ High-Side MOSFET
The PI5PD2560/2561 is dual-channel power-distribution
switch intended for applications where precision current
limiting is required or heavy capacitive loads and short
circuits are encountered. These devices offer a
programmable current-limit threshold between 250 mA
and 2.8A (typ) per channel via an external resistor. The
power-switch rise and fall times are controlled to
minimize current surges during turn on/off.
Operating Range: 2.5 V to 5.5V
2μA Maximum Standby Supply Current
Reverse Input-Output Voltage Protection
Built-in Soft-Start
Each channel of the PI5PD2560/2561 devices limit the
output current to a safe level by switching into a
constant-current mode when the output load exceeds the
current-limit threshold.
15 kV / 8 kV System-Level ESD Capable
Device Package: TDFN 3x3-10L
UL Listed – File No. E341484
CB Certified
The FAULTx logic output for each channel
independently asserts low during over-current or over
temperature.
Applications
USB Ports/Hubs
Digital TV
Set-Top Boxes
VOIP Phones
Typical Application Circuit
VIN
IN
IN
O UT1
O UT2
Pin Configuration
C4
R1
R2
C1
C2
0.1uF
10
9
GND
/FAULT1
OUT1
1
2
100k
100k
C3
IN
IN
/FAU LT1
/FAU LT2
ILIM
OUT2
8
7
6
3
4
5
R3
EN1
EN2
ILIM
Logic signal
EN1
EN2
G ND
/FAULT2
P ower Pad
TDFN3.0x3.0-10L(Top View)
Pin Description
Pin No.
Pin Name
Type
Description
PI5PD2560
PI5PD2561
1
2, 3
4
GND
IN
-
I
I
Ground.
Power input voltage.
Enable input, logic low/high turns on channel one power switch.
/EN1
/EN2
EN1
EN2
5
I
Enable input, logic low/high turns on channel two power switch.
Active-low open-drain output, asserted during over-current or
over-temperature condition occur on channel 2
External resistor used to set current-limit threshold; recommended
20 kΩ ≤ RILIM ≤ 187 kΩ.
6
/FAULT2
ILIM
O
7
I
8
9
OUT2
OUT1
O
O
Power switch output for channel two
Power switch output for channel one
Active-low open-drain output, asserted during over-current or
over-temperature condition occur on channel 1
10
/FAULT1
O
2016-03-0004
PT0489-5
04/29/16
1
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Maximum Ratings
Note:
o
o
1. Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating only
and functional operation of the device at these or
any other conditions above those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
reliability.
2. The JEDEC high-K (2s2p) board used to derive
this data was a 3in × 3in, multilayer board with 1-
ounce internal power and ground planes and 2-
ounce copper traces on top and bottom of the board.
StorageTemperature...................................................................................-65 Cto+150 C
SupplyVoltage toGroundPotential............................................................-0.5Vto+6.0V
DCInputVoltage......................................................................................-0.5VtoVDD+0.5V
VoltagerangefromINtoOUTx....................................................................-0.5Vto+6.0V
ControlInputVoltage(VINx).........................................................................-0.5Vto+6.0V
(1)
Continuoustotalpowerdissipation .......................................................................2400mW
ContinuousFAULTxsinkcurrent................................................................................25mA
PowerDissipation.............................................................................................................. 0.5W
ESD:HBMMode...........................................................................................................4000V
CDMMode..............................................................................................................500V
ESD-systemlevel(contact/air)...............................................................................8kV/15kV
Recommended operation conditions
Symbol
Parameter
Conditions
Min
2.5
0
Typ Max Unit
V
IN
Input Voltage
Input Voltage
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5.5
5.5
5.5
-
V
VENx
PI5PD2560
PI5PD2561
V
V/ENx
0
V
IH
High-level input voltage on ENx
1.1
-
V
V
V
IL
Low-level input voltage on ENx
0.66
2.5
10
IOUTx
Continuous output current per channel, OUTx
0
A
IFAULTx Continuous /FAULTx sink current
-
mA
kΩ
ºC
R
ILIM
Recommended resistor limit range
Operating Temperature Range
20
-40
187
85
TA
2016-03-0004
PT0489-5
04/29/16
2
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
DC Electrical Characteristics
VI(IN)= 5.0V; TA=-40°C to +85°C ; unless otherwise specified.
Sym
Description
Test Conditions(1)
Min
Typ
Max
Unit
Power Switch
RDS(on)
Static drain-source on-state resistance
Rise time, output
-
-
44
70
mΩ
VI(IN) = 5.0V
1
2
1
0.5
0.4
4
3
1.0
0.6
tr
tf
VI(IN) = 2.5V
VI(IN) = 5.0V
VI(IN) = 2.5V
0.5
0.3
0.2
CL = 1F,
ms
µs
RL = 100Ω
Fall time, output
-
-
-
tIOS
Response time to short circuit
VIN = 5.0 V
3.5
Enable ENx
VIH
VIL
ton
High-level input voltage
Low-level input voltage
Turn on time
2.5 V ≤ VI(IN) ≤ 5.5 V
2.5 V ≤ VI(IN) ≤ 5.5 V
1.1
-
-
-
-
-
-
0.6
5
V
ms
CL = 1F, RL = 100Ω
toff
Turn off time
-
-
2
Current Limit
RILIM=20kΩ
RILIM=61.9kΩ
2590
800
2800
900
3005
1005
Current-limit threshold @ VOUTx = VIN * 0.8
IOS
RILIM=100kΩ
400
560
645
mA
VIN = 5 V, current ramp (≤ 100 A/s)
on OUT ,RILIM=20.0kΩ
2700
3160
3600
Overcurrent trip threshold
IOC_TRIP
VIN = 5 V, current ramp (≤ 100 A/s)
on OUT ,RILIM=100kΩ
450
-
650
3.5
800
-
tIOS
Response time to short circuit
VIN = 5.0V
s
Supply Current
No load on OUT, VEN=disable
TA =25°C
ISTB
Input supply current at output disable
-
0.1
2
No load on OUT,
VEN=5.0V ,
TA=25°C
RILIM=20kΩ
-
-
-
100
85
125
110
1.0
A
ISS
Input supply current at output enable
Reverse Leakage Current
RILIM=100kΩ
IREV
0.01
VOUTx=5.5V, VIN=0V， TA=25°C
Under Voltage Lockout
UVLO Low-level input voltage
Hysteresis for low-level input voltage
/FAULTx FLAG
VIN Rising
TA=25°C
-
-
2.35
35
2.45
-
V
mV
VOL
IOFF
Output low voltage
I/FAULTx =1mA
V/FAULTx =5.5V
-
-
-
-
180
1
mV
Off-state leakage
/FAULTx deglitch
A
FAULTx assertion or de-assertion
due to over-current condition
TD
4
9
15
ms
Thermal Shutdown
-
-
-
-
-
-
155
135
20
-
-
-
OTSD2
OTSD
Thermal shutdown threshold
Thermal shutdown threshold in current-
limit
°C
Hysteresis
Note:
Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
2016-03-0004
PT0489-5
04/29/16
3
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
PARAMETER MEASUREMENT INFORMATION
Figure1 Test Circuit and Voltage Waveforms
Figure2 Response Time to Short Circuit Waveform
TYPICAL CHARACTERISTICS
VIN
IN
IN
OUT1
OUT2
ChannelOne Output
ChannelTwoOutput
C3
R1
R2
C1
0.1uF
100k
100k
C2
/FAULT1
/FAULT2
/FAULT1 Signal
/FAULT2 Signal
ILIM
R3
EN1
EN2
Chennel One Control Input
Chennel Two Control Input
GND
P ower Pad
Figure3. Typical Characteristics Reference Schematic
2016-03-0004
PT0489-5
04/29/16
4
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
TYPICAL CHARACTERISTICS (Continued)
Figure 4. UVLO – Under voltage Lockout – V
Figure 6. IIN – Supply Current, Output Enabled – µA
Figure 7. IIN – Supply Current, Output Enabled – µA
2016-03-0004
PT0489-5
04/29/16
5
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
TYPICAL CHARACTERISTICS (Continued)
Figure 8. MOSFET rDS(on) Vs. Junction
Temperature
2016-03-0004
PT0489-5
04/29/16
6
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Functional Description
Block Diagram
Overview
The PI5PD2560/2561 are a dual-channel, current-limited power-distribution switch using N-channel MOSFETs for applications
where short circuits or heavy capacitive loads will be encountered. This device allows the user to program the current-limit
threshold between 250 mA and 2.8 A (typ) per channel via an external resistor. This device incorporates an internal charge pump
and gate drive circuitry necessary to drive the N-channel MOSFETs. The charge pump supplies power to the driver circuit for
each channel and provides the necessary voltage to pull the gate of the MOSFET above the source. The charge pump operates
from input voltages as low as 2.5 V and requires little supply current. The driver controls the gate voltage of the power switch. The
driver incorporates circuitry that controls the rise and fall times of the output voltage to limit large current and voltage surges and
provides built-in soft-start functionality. Each channel of the PI5PD2560/2561 limit the output current to the programmed current-
limit threshold IOS during an over-current or short-circuit event by reducing the charge pump voltage driving the N-channel
MOSFET and operating it in the linear range of operation. The result of limiting the output current to IOS reduces the output
voltage at OUTx because the N-channel MOSFET is no longer fully enhanced.
Over-current Conditions
When an over-current condition is detected, the device maintains a constant output current and reduces the output voltage
accordingly.
The PI5PD2560/2561 thermal cycles if an overload condition is present long enough to activate thermal limiting in any of the
above cases. The device turns off when the junction temperature exceeds 135°C (min) while in current limit. The device remains
off until the junction temperature cools 20°C (typ) and then restarts. The PI5PD2560/2561 cycles on/off until the overload is
removed.
/FAULTx Response
The /FAULTx open-drain outputs are asserted (active low) on an individual channel during an over-current or Over temperature
condition. The PI5PD2560/2561 assert the FAULTx signal until the fault condition is removed and the device resumes normal
operation on that channel. The PI5PD2560/2561 are designed to eliminate false FAULTx reporting by using an internal delay
"deglitch" circuit (9-ms typ) for over-current conditions without the need for external circuitry. This ensures that FAULTx is not
accidentally asserted due to normal operation such as starting into a heavy capacitive load. The deglitch circuitry delays entering
and leaving current-limited induced fault conditions. The FAULTx signal is not deglitched when the MOSFET is disabled due to
an over temperature condition but is deglitched after the device has cooled and begins to turn on. This unidrectional deglitch
prevents FAULTx oscillation during an overt temperature event.
2016-03-0004
PT0489-5
04/29/16
7
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Under-voltage Lockout (UVLO)
The under-voltage lockout (UVLO) circuit disables the power switch until the input voltage reaches the UVLO turn-on threshold.
Built-in hysteresis prevents unwanted on/off cycling due to input voltage droop during turn on.
Enable (ENx OR /ENx)
The logic enables control the power switches and device supply current. The supply current is reduced to less than 2μA when a
logic high is present on /ENx or when a logic low is present on ENx. A logic low input on /ENx or a logic high input on ENx
enables the driver, control circuits, and power switches. The enable inputs are compatible with both TTL and CMOS logic levels.
Thermal Sense
The PI5PD2560/2561 self protect by using two independent thermal sensing circuits that monitor the operating temperature of the
power switch and disable operation if the temperature exceeds recommended operating conditions. Each channel of the
PI5PD2560/2561 operate in constant-current mode during over-current conditions, which increases the voltage drop across the
power switch. The power dissipation in the package is proportional to the voltage drop across the power switch, which increases
the junction temperature during an over-current condition. The first thermal sensor (OTSD) turns off the individual power switch
channel when the die temperature exceeds 135°C (min) and the channel is in current limit. Hysteresis is built into the thermal
sensor, and the switch turns on after the device has cooled approximately 20°C.
The PI5PD2560/2561 also have a second ambient thermal sensor (OTSD2). The ambient thermal sensor turns off both power
switch channels when the die temperature exceeds 155°C (min) regardless of whether the power switch channels are in current
limit and will turn on the power switches after the device has cooled approximately 20°C. The PI5PD2560/2561 continue to cycle
off and on until the fault is removed.
APPLICATION INFORMATION
INPUT AND OUTPUT CAPACITANCE
Input and output capacitance improves the performance of the device; the actual capacitance should be optimized for the particular
application. For all applications, a 0.1μF or greater ceramic bypass capacitor between IN and GND is recommended as close to the
device as possible for local noise decoupling. This precaution reduces ringing on the input due to power-supply transients.
Additional larger input capacitance with low ESR is needed on the input to reduce voltage overshoot from exceeding the absolute
maximum voltage of the device during heavy transient conditions. This is especially important during bench testing when long,
inductive cables are used to connect the evaluation board to the bench power supply.
Output capacitance is not required, but placing a high-value electrolytic capacitor on the output pin is recommended when large
transient currents are expected on the output.
PROGRAMMING THE CURRENT-LIMIT THRESHOLD
The over-current threshold is user programmable via an external resistor, RILIM. RILIM sets the current-limit threshold for both
channels. The PI5PD2560/2561 use an internal regulation loop to provide a regulated voltage on the ILIM pin. The current-limit
threshold is proportional to the current sourced out of ILIM. The recommended 1% resistor range for RILIM is 20 kΩ ≤ RILIM ≤
187 kΩ to ensure stability of the internal regulation loop. Many applications require that the minimum current limit is above a
certain current level or that the maximum current limit is below a certain current level, so it is important to consider the tolerance
of the over-current threshold when selecting a value for RILIM. The following equations calculates the resulting overcurrent
threshold for a given external resistor value (RILIM). The traces routing the RILIM resistor to the PI5PD2560/2561 should be as
short as possible to reduce parasitic effects on the current-limit accuracy.
52850V
IOSmax (mA) =
RILIM0.957kΩ
56000V
RILIMkΩ
IOSnom (mA) =
61200V
IOSmin (mA) =
RILIM1.056kΩ
2016-03-0004
PT0489-5
04/29/16
8
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
(2)
Figure 9. Current-Limit Threshold vs. RILIM
APPLICATION 1: DESIGNING ABOVE A MINIMUM CURRENT LIMIT
Some applications require that current limiting cannot occur below a certain threshold. For this example, assume that 2 A must be
delivered to the load so that the minimum desired current-limit threshold is 2000 mA. Use the IOS equations and Figure 9 to
select RILIM.
IOSmax (mA) = 2000mA
61200V
IOSmin (mA) =
RILIM1.056kΩ
1
61200V
IOsmin mA
1.056
RILIM (kΩ) =
RILIM (kΩ) = 25.52kΩ
Select the closest 1% resistor less than the calculated value: RILIM = 25.5 kΩ. This sets the minimum current-limit threshold at
2A. Use the IOS equations, Figure 9, and the previously calculated value for RILIM to calculate the maximum resulting current-
limit threshold
RILIM (kΩ) = 25.52kΩ
52850V
IOSmax (mA) =
RILIM0.957kΩ
52850V
IOSmax (mA) =
25.50.957kΩ
IOSmax (mA) = 2382mA
The resulting maximum current-limit threshold is 2382 mA with a 25.5 kΩ resistor
2016-03-0004
PT0489-5
04/29/16
9
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
APPLICATION 2: DESIGNING BELOW A MAXIMUM CURRENT LIMIT
Some applications require that current limiting must occur below a certain threshold. For this example, assume that the desired
upper current-limit threshold must be below 1000 mA to protect an up-stream power supply. Use the IOS equations and Figure 9
to select RILIM.
IOSmax (mA) = 1000mA
52850V
IOSmax (mA) =
RILIM0.957kΩ
1
52850V
IOsmaxmA
0.957
RILIM (kΩ) =
RILIM (kΩ) = 63.16kΩ
Select the closest 1% resistor greater than the calculated value: RILIM = 63.4 kΩ. This sets the maximum current-limit threshold
at 1000 mA. Use the IOS equations, Figure 9, and the previously calculated value for RILIM to calculate the minimum resulting
current-limit threshold
RILIM (kΩ) = 63.4kΩ
61200V
IOSmin (mA) =
RILIM1.056kΩ
61200V
IOSmin (mA) =
63.41.056kΩ
IOSmin (mA) = 765mA
The resulting minimum current-limit threshold is 765 mA with a 63.4 kΩ resistor.
ACCOUNTING FOR RESISTOR TOLERANCE
The previous sections described the selection of RILIM given certain application requirements and the importance of understanding
the current-limit threshold tolerance. The analysis focused only on the PI5PD2560A/2561A performance and assumed an exact
resistor value. However, resistors sold in quantity are not exact and are bounded by an upper and lower tolerance centered around
a nominal resistance. The additional RILIM resistance tolerance directly affects the current-limit threshold accuracy at a system
level. The following table shows a process that accounts for worst-case resistor tolerance assuming 1% resistor values. Step one
follows the selection process outlined in the application examples above. Step two determines the upper and lower resistance
bounds of the selected resistor. Step three uses the upper and lower resistor bounds in the IOS equations to calculate the threshold
limits. It is important to use tighter tolerance resistors, e.g. 0.5% or 0.1%, when precision current limiting is desired.
Desired Nominal
Current Limit
(mA)
Ideal
Resistor
(kΩ)
Closest 1%
Resistor
(kΩ)
Resistor Tolerance
Actual Limits
1% low
(kΩ)
185.1
1%
high(kΩ)
188.9
IOS MIN
(mA)
241.6
328
504.6
684
859.9
1052.8
1225
1426.5
1617.3
1794.7
1981
2188.9
2372.1
2560.4
IOS Nom
(mA)
299.5
IOS MAX
(mA)
300
400
600
186.7
140
93.3
70
56
46.7
40
35
31.1
28
25.5
23.3
21.5
20
187
140
93.1
69.8
56.2
46.4
40.2
34.8
30.9
28
357.3
471.4
696.5
138.6
92.2
69.1
55.6
45.9
39.8
34.5
30.6
27.7
25.2
23
141.4
94
400
601.5
802.3
996.4
1206.9
1393
1609.2
1812.3
2000
2196.1
2413.8
2604.7
2800
800
70.5
56.8
46.9
40.6
35.1
31.2
28.3
25.8
23.4
21.7
20.2
917.6
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
1129.1
1356.3
1555.9
1786.2
2001.4
2199.3
2405.3
2633
25.5
23.2
21.5
20
21.3
19.8
2831.9
3034.8
2016-03-0004
PT0489-5
04/29/16
10
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
AUTO-RETRY FUNCTIONALITY
Some applications require that an overcurrent condition disables the part momentarily during a fault condition and re-enables after
a pre-set time. This auto-retry functionality can be implemented with an external resistor and capacitor. During a fault condition,
FAULTx pulls ENx low disabling the part. The part is disabled when ENx is pulled below the turn-off threshold, and FAULTx
goes high impedance allowing CRETRY to begin charging. The part re-enables when the voltage on ENx reaches the turn-on
threshold, and the auto-retry time is determined by the resistor/capacitor time constant. The part will continue to cycle in this
manner until the fault condition is removed.
VIN
IN
IN
OUT1
OUT2
VOUT1
VOUT2
C3
R1
R2
C1
0.1uF
100k
100k
C2
/FAULT1
EN1
ILIM
R3
20k
C2
0.22uF
/FAULT2
EN2
GND
P ower Pad
C3
0.22uF
Figure 10.Auto-Retry Functionality
Some applications require auto-retry functionality and the ability to enable/disable with an external logic signal. The figure below
shows how an external logic signal can drive EN through RFAULT and maintain auto-retry functionality. The resistor/capacitor
time constant determines the auto-retry time-out period.
VIN
IN
IN
OUT1
OUT2
VOUT1
VOUT2
C3
C1
Logic signal & drivers
0.1uF
C2
R1
/FAULT1
EN1
100k
ILIM
R3
20k
R2
100k
/FAULT2
EN2
GND
C2
P ower Pad
C3
0.22uF
0.22uF
Figure 11.Auto-Retry Functionality With External EN Signal
2016-03-0004
PT0489-5
04/29/16
11
PI5PD2560/2561
Dual Channel,
Adjustable Current-Limited Power Switch
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Mechanical Information
TDFN 3.0x3.0-10L
Ordering Information
Part No.
Package Code
Package
Lead free and Green 10-pin TDFN3.0x3.0
Tape & reel
PI5PD2560ZEEX
PI5PD2561ZEEX
ZE
ZE
Lead free and Green 10-pin TDFN3.0x3.0
Tape & reel
Note:
E = Pb-free and Green
Adding X Suffix= Tape/Reel
Pericom Semiconductor Corporation 1-800-435-2336 www.pericom.com
Pericom reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply
the best possible product. Pericom does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom product. The
company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom.
2016-03-0004
PT0489-5
04/29/16
12
相关型号：
PI5USB1457AZAEX
Power Supply Support Circuit, Fixed, 1 Channel, PDSO8, 2 X 2 MM, 0.75 MM HEIGHT, GREEN, MO-229, TDFN-8
DIODES
PI5USB1457BZAE
Power Supply Support Circuit, Fixed, 1 Channel, PDSO8, 2 X 2 MM, 0.75 MM HEIGHT, GREEN, MO-229, TDFN-8
DIODES
PI5USB1457BZAEX
Power Supply Support Circuit, Fixed, 1 Channel, PDSO8, 2 X 2 MM, 0.75 MM HEIGHT, GREEN, MO-229, TDFN-8
DIODES
PI5USB1458
USB Host Charger Controller supporting BC1.2, YD/T-1591, & Non-standard Protocols
PERICOM
PI5USB1458AZAE
USB Host Charger Controller supporting BC1.2, YD/T-1591, & Non-standard Protocols
PERICOM
PI5USB1458ZAE
USB Host Charger Controller supporting BC1.2, YD/T-1591, & Non-standard Protocols
PERICOM
PI5USB1468
USB Host Charger Controller supporting BC1.2, YD/T-1591, & non-standard protocols
PERICOM
PI5USB1468AZAE
USB Host Charger Controller supporting BC1.2, YD/T-1591, & non-standard protocols
PERICOM
©2020 ICPDF网 联系我们和版权申明