PI74AUC16244K [PERICOM]

1.8V 16-Bit Buffer/Driver with 3-State Outputs; 1.8V 16位缓冲器/驱动器,具有三态输出
PI74AUC16244K
型号: PI74AUC16244K
厂家: PERICOM SEMICONDUCTOR CORPORATION    PERICOM SEMICONDUCTOR CORPORATION
描述:

1.8V 16-Bit Buffer/Driver with 3-State Outputs
1.8V 16位缓冲器/驱动器,具有三态输出

驱动器
文件: 总7页 (文件大小:369K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
PI74AUC16244  
1.8V 16-Bit Buffer/Driver  
with 3-State Outputs  
Features  
Description  
• PI74AUC16244 is designed for low-voltage operation,  
Pericom Semiconductor’s PI74AUC series of logic circuits are  
produced using the Company’s advanced submicron CMOS  
technology, achieving industry leading speeds.  
V
= 0.8V to 2.7V, optimized at 1.8V.  
CC  
• 3.6V I/O Tolerant inputs and outputs  
• I supports partial power-down operation  
The PI74AUC16244 is a 16-bit buffer driver designed specifically  
to improve both the performance and density of 3-state memory  
address drivers, clock drivers and bus-oriented receivers and  
transmitters.  
OFF  
• Latch-Up Performance exceeds 100mA per JESD 78  
• ESD Protection Exceeds JESD 22  
– 2000V Human-Body Model (A114-B)  
– 200V Machine Model (A115-A)  
The device can be used as four 4-bit buffers, two 8-bit buffers, or  
one16-bitbuffer.Itprovidesnon-invertingoutputsandsymmetrical  
active-low output-enable OE inputs.  
• Industrial operation: –40°C to +85°C  
To ensure the high-impedance state during power-up or power  
• Packaging:  
– 48-pin TSSOP (A)  
– 48-pin TSSOP (K)  
-down, OE should be tied to V through a pull-up resistor; the  
CC  
minimum value of the resistor is determined by the current-sinking  
ability of the driver.  
ThePI74AUC16244isspecifiedforpartialpowerdownapplications  
usingI  
TheI  
circuitrydisablestheoutputspreventingcurrent  
OFF.  
OFF  
backflow through the device when it is powered down.  
Block Diagram  
1
25  
1OE  
3OE  
2
13  
47  
36  
1A1  
1Y1  
1Y2  
1Y3  
1Y4  
3A1  
3A2  
3A3  
3A4  
3Y1  
3Y2  
3Y3  
3Y4  
3
14  
46  
35  
1A2  
5
16  
17  
44  
33  
32  
1A3  
6
43  
1A4  
48  
24  
30  
2OE  
4OE  
4A1  
8
9
19  
20  
41  
40  
2A1  
2A2  
2A3  
2A4  
2Y0  
2Y1  
2Y2  
2Y3  
4Y1  
4Y2  
4Y3  
4Y4  
29  
4A2  
4A3  
4A4  
11  
12  
22  
23  
38  
37  
27  
26  
PS8731  
08/16/04  
A
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.)  
Notes:  
Supply voltage range, V  
–0.5V to +3.6V  
–0.5V to +3.6V  
CC ..................................  
(1)  
1. Input negative voltage & output voltage ratings may be  
exceeded if the input and output current rating are observed.  
2. This value is limited to 3.6V maximium.  
3. The package thermal impedance is calculated in accordance with  
JESD 51.  
Input voltage range, V  
I
.....................................  
Voltage range applied to any output in the  
(1)  
high-impedance or power-off state, V  
.... –0.5V to +3.6V  
O
(1, 2)  
Output voltage range V  
............... –0.5V to V +0.5V  
CC  
O
4. Stresses greater than those listed under MAXIMUM  
RATINGS may cause permanent damage to the device.  
Thisisastressratingonlyandfunctionaloperationofthedeviceatthese  
oranyotherconditionsabovethoseindicatedintheoperationalsections  
of this specification is not implied. Exposure to absolute maximum  
rating conditions for extended periods may affect reliability.  
Input clamp current, I (V < 0).................................. –50mA  
IK  
I
Output clamp current, I (V < 0)............................. –50mA  
OK  
O
Continuous output current, I .................................... ±20mA  
O
Continuous current through each V or GND ......... ±100mA  
CC  
(3)  
Package thermal impedance, θ  
: package A........ 104°C/W  
package K........ 107°C/W  
JA  
Storage Temperature range, T ....................–65°C to 150°C  
stg  
Pin Description  
Pin Configuration  
Pin Name  
Description  
ꢉꢊ  
�  
ꢂꢆ  
ꢂꢅ  
ꢂꢄ  
ꢂꢃ  
ꢂꢂ  
ꢂꢁ  
ꢂꢀ  
ꢂ�  
ꢂꢈ  
ꢁꢇ  
ꢁꢆ  
ꢁꢅ  
ꢁꢄ  
ꢁꢃ  
ꢁꢂ  
ꢁꢁ  
ꢁꢀ  
ꢁ�  
ꢁꢈ  
ꢀꢇ  
ꢀꢆ  
ꢀꢅ  
ꢀꢄ  
ꢀꢃ  
ꢉꢊ  
�  
OE  
3-State Output Enable Inputs (Active LOW)  
X
X
X
A
Y
Inputs  
X
X
ꢀ  
ꢀ  
3-State Outputs  
Ground  
ꢌꢍꢎ  
ꢁ  
ꢌꢍꢎ  
ꢁ  
GND  
V
Power  
CC  
ꢂ  
ꢂ  
ꢐꢐ  
�  
ꢐꢐ  
�  
Truth Table  
ꢀ  
ꢀ  
�ꢈ  
��  
�ꢀ  
�ꢁ  
�ꢂ  
�ꢃ  
�ꢄ  
�ꢅ  
�ꢆ  
�ꢇ  
ꢀꢈ  
ꢀ�  
ꢀꢀ  
ꢀꢁ  
ꢀꢂ  
Inputs  
Outputs  
ꢌꢍꢎ  
ꢌꢍꢎ  
ꢁ  
ꢂ  
ꢁ  
ꢂ  
�  
ꢀ  
ꢌꢍꢎ  
OE  
L
A
H
L
Y
H
L
X
X
X
X
X
�  
L
ꢀ  
H
X
ꢌꢍꢎ  
Note:  
1. H = High Signal Level, L = Low Signal Level  
ꢁ  
ꢁ  
ꢂ  
ꢂ  
X = Don’t Care or Irrelevant, Z = High Impedance  
ꢐꢐ  
ꢐꢐ  
�  
ꢀ  
�  
ꢀ  
ꢌꢍꢎ  
ꢁ  
ꢌꢍꢎ  
ꢁ  
ꢂ  
ꢂ  
ꢉꢊ  
ꢁꢉꢊ  
PS8731  
08/16/04  
2
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
(1)  
Recommended Operating Conditions  
Parameters  
Description  
Operating Conditions  
Min.  
Max.  
Units  
V
V
SupplyVoltage  
0.8  
2.7  
CC  
V
V
V
V
V
V
= 0.8V  
V
CC  
CC  
CC  
CC  
CC  
CC  
CC  
High-Level Input Voltage  
Low-Level Input Voltage  
= 1.1V to 1.95V  
= 2.3V to 2.7V  
= 0.8V  
0.65 x V  
1.7  
IH  
CC  
0
0.35 x V  
0.7  
V
V
= 1.1V to 1.95V  
= 2.3V to 2.7V  
IL  
CC  
V
V
Input Voltage  
0
0
0
3.6  
I
Active State  
3-state  
V
CC  
Output Voltage  
O
3.6  
V
V
V
V
V
V
V
V
V
V
= 0.8V  
= 1.1V  
= 1.4V  
= 1.65V  
= 2.3V  
= 0.8V  
= 1.1V  
= 1.4V  
= 1.65V  
= 2.3V  
CC  
CC  
CC  
CC  
CC  
CC  
CC  
CC  
CC  
CC  
I
I
High-Level Output Current  
Low-Level Output Current  
OH  
mA  
OL  
∆t/∆v  
Input Transition Rise or Fall Rate  
Operating Free-Air Temperature  
5
ns/V  
°C  
T
A
-40  
85  
Note:  
1. All unused inputs must be held at VCC or GND to ensure proper device operation.  
PS8731  
08/16/04  
3
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
DC Electrical Characteristics (Over the Operating Range, T = –40°C +85°C)  
A
(1)  
(1)  
Parameters  
Test Conditions  
= -100µA  
= -0.7mA  
= -3mA  
V
Min.  
V -0.1V  
CC  
Typ.  
Max.  
Units  
CC  
I
I
I
I
I
I
I
I
I
I
I
I
0.8V to 2.7V  
0.8V  
OH  
OH  
OH  
OH  
OH  
OH  
OL  
OL  
OL  
OL  
OL  
OL  
0.55  
1.1V  
0.8  
1
V
OH  
= -5mA  
1.4V  
= -8mA  
1.65V  
1.2  
1.8  
= -9mA  
2.3V  
V
= 100µA  
= 0.7mA  
= 3mA  
0.8V to 2.7V  
0.8V  
0.2  
0.25  
1.1V  
0.3  
0.4  
0.45  
0.6  
±5  
V
OL  
= 5mA  
1.4V  
= 8mA  
1.65V  
= 9mA  
2.3V  
(2)  
I
I
I
I
V = V or GND  
0 to 2.7V  
0V  
I
I
CC  
V or V = 2.7V  
±10  
±10  
20  
OFF  
OZ  
I
O
µA  
pF  
V = V or GND  
0.8V to 2.7V  
0.8V to 2.7V  
2.5V  
O
CC  
V = V or GND, I = 0  
CC  
I
CC  
O
C
C
V = V or GND  
3
4
I
I
CC  
V = V or GND  
2.5V  
O
O
CC  
Note:  
1. Typical values are measured at TA = 25°C.  
2. II - A Port or OE inputs.  
Switching Characteristics  
(Over recommended operating free-air temperature range, unless otherwise noted, see Figure 1)  
V
=
V
= 1.2V  
± 0.1V  
V
= 1.5V  
± 0.1V  
V
= 1.8V  
± 0.15V  
V
= 2.5V  
CC  
± 0.2V  
CC  
CC  
CC  
CC  
From  
(Input) (Output)  
To  
0.8V  
Typ.  
5.4  
8
Parameters  
Units  
Min. Max. Min.  
Max. Min. Typ. Max. Min. Max.  
tpd  
ten  
tdis  
A
Y
Y
Y
0.8  
1
2.8  
4.4  
4.9  
0.6  
0.7  
1
1.9  
2.6  
4.6  
0.7  
0.8  
1.5  
1.3  
1.4  
2.6  
1.8  
2.5  
4
0.5  
0.6  
0.5  
1.8  
1.9  
3
OE  
OE  
ns  
12  
1.9  
Operating Characteristics, T = 25°C  
A
V
= 0.8V  
V
= 1.2V  
V
= 1.5V  
V
= 1.8V  
V = 2.5V  
CC  
CC  
CC  
CC  
CC  
Test  
Parameters  
Units  
Conditions  
Typical  
Typical  
Typical  
Typical  
Typical  
Outputs  
Enabled  
21  
22  
23  
25  
30  
Cpd Power  
Dissipation  
Capacitance  
C = 0pF,  
f = 10 MHz  
L
pF  
Outputs  
Disabled  
1
1
1
1
1
PS8731  
08/16/04  
4
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
Parameter Measurement Information  
2xVCC  
Open  
GND  
Test  
/t  
S1  
S1  
RL  
From Output  
Under Test  
t
t
Open  
2 x V  
CC  
PLH PHL  
/t  
PLZ PZL  
t
/t  
GND  
PHZ PZH  
CL  
RL  
(See Note 1)  
V
C
R
L
V∆  
CC  
L
0.8V  
15pF  
15pF  
15pF  
30pF  
30pF  
2kΩ  
2kΩ  
2kΩ  
1kΩ  
500Ω  
0.1V  
0.1V  
0.1V  
0.15V  
0.15V  
1.2V ± 0.1V  
1.5V ± 0.1V  
1.8V ± 0.15V  
2.5V ± 0.2V  
Load Circuit  
V
CC  
CC  
Timing  
Input  
V
/2  
CC  
0V  
t
t
h
su  
tW  
V
CC  
V
V
/2  
V
/2  
Data  
Input  
Input  
CC  
CC  
V
/2  
V
/2  
CC  
CC  
0V  
0V  
Voltage Waveforms Pulse Duration  
Voltage Waveforms Setup and Hold Times  
VCC  
Output  
Control  
(Low Level  
Enabling)  
VCC/2  
VCC/2  
tPLZ  
VCC  
0V  
VCC/2  
tPLH  
VCC/2  
tPHL  
Input  
tPZL  
0V  
Output  
Waveform 1  
S1 at 2 x VCC  
(see Note 2)  
VCC  
VCC/2  
VOH  
VOL +V  
tPHZ  
VOL  
VOH  
/2  
VCC  
VCC/2  
tPZH  
Output  
Output  
VOL  
VOH  
Output  
Waveform 2  
S1 at GND  
(see Note 2)  
tPHL  
tPLH  
VOH –V∆  
VCC/2  
/2  
/2  
VCC  
VCC  
0V  
VOL  
Voltage Waveforms Propagation Delay Times  
Voltage Waveforms Enable and Disable Times  
Figure 1. Load Circuit and Voltage Waveforms  
Notes:  
1. CL includes probe and jig capacitance.  
2. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.  
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.  
3. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50Ω, slew rate ≥ 1V/ns  
4. The outputs are measured one at a time with one transition per measurement.  
5. tPLZ and tPHZ are the same as tdis  
6. tPZL and tPZH are the same as ten  
7. tPLH and tPHL are the same as tpd  
8. All parameters and waveforms are not applicable to all devices.  
PS8731  
08/16/04  
5
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
Packaging Mechanical: 48-pin TSSOP (A)  
48  
.236  
.244  
6.0  
6.2  
1
.488 12.4  
.496 12.6  
.047  
1.20 Max  
SEATING PLANE  
0.09  
0.20  
.004  
.008  
0.45 .018  
0.75 .030  
.002  
.006  
0.05  
0.15  
.007  
.010  
.0197  
BSC  
.319  
BSC  
X.XX  
X.XX  
DENOTES DIMENSIONS  
IN MILLIMETERS  
0.50  
0.17  
0.27  
8.1  
Packaging Mechanical: 48-pin TSSOP (K)  
48  
.169  
.177  
4.30  
4.50  
0.09  
0.20  
.0035  
.008  
1
.031  
.041  
0.80  
1.05  
0.45 .018  
0.75 .030  
.252  
BSC  
6.4  
.378 9.60  
.386 9.80  
SEATING  
PLANE  
Max.  
.047  
1.20  
.002  
.006  
0.05  
0.15  
.016  
BSC  
.0051  
.009  
0.13  
0.23  
0.40  
X.XX DENOTES DIMENSIONS  
X.XX IN MILLIMETERS  
PS8731  
08/16/04  
6
PI74AUC16244  
1.8V 16-Bit Buffer Driver  
with 3-State Outputs  
Ordering Information  
Ordering Code  
Packaging Code  
Package Description  
PI74AUC16244A  
A
K
48-pin TSSOP  
48-pin TVSOP  
PI74AUC16244K  
Notes:  
1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/.  
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com  
PS8731  
08/16/04  
7

相关型号:

PI74AUC16244KE

Bus Driver, 4-Func, 4-Bit, True Output, CMOS, PDSO48, 0.173 INCH, PLASTIC, TVSOP-48
PERICOM

PI74AUC16245AE

Bus Transceiver, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM

PI74AUC16245KE

Bus Transceiver, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.173 INCH, PLASTIC, TVSOP-48
PERICOM

PI74AUC164245

16-Bit 0.8V to 2.7V Scaled Configurable Level Shifting Transceiver with 3-State Outputs1DIR1OE1B11471A1To
PERICOM

PI74AUC164245A

16-Bit 0.8V to 2.7V Scaled Configurable Level Shifting Transceiver with 3-State Outputs1DIR1OE1B11471A1To
PERICOM

PI74AUC164245AE

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, GREEN, PLASTIC, TSSOP-48
PERICOM

PI74AUC164245AEX

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, GREEN, PLASTIC, TSSOP-48
PERICOM

PI74AUC164245AX

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.240 INCH, PLASTIC, TSSOP-48
PERICOM

PI74AUC164245K

16-Bit 0.8V to 2.7V Scaled Configurable Level Shifting Transceiver with 3-State Outputs1DIR1OE1B11471A1To
PERICOM

PI74AUC164245KE

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.173 INCH, GREEN, PLASTIC, TVSOP-48
PERICOM

PI74AUC164245KEX

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.173 INCH, GREEN, PLASTIC, TVSOP-48
PERICOM

PI74AUC164245KX

Bus Transceiver, AUC Series, 2-Func, 8-Bit, True Output, CMOS, PDSO48, 0.173 INCH, PLASTIC, TVSOP-48
PERICOM