PT8A3517DWE [PERICOM]
Analog Circuit, 1 Func, CMOS, PDSO8, GREEN, MS-012EAA, SOIC-8;型号: | PT8A3517DWE |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | Analog Circuit, 1 Func, CMOS, PDSO8, GREEN, MS-012EAA, SOIC-8 光电二极管 |
文件: | 总8页 (文件大小:280K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PT8A3514/15/16/17/18/19(C/D)
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Smart Iron Controller
Features
Description
The PT8A3514/15/16/17/18/19(C/D) are high
performance low power and low cost CMOS chips
designed for intelligent electric IRON controller. Their
intelligence mainly results from their sensitive
detection to the movement and static position of
electric iron by using a special sensor. With the sensor,
these chips can detect the vertical/horizontal position
and movement status of IRON.
Build in RC oscillator for sensor signal detection
On chip shunt regulated power supply
Using AC 60Hz/50Hz as timer clock can select by
Part No.
Accurate timer with error dropping in ±1%
Sensitive movement detection
Powerful immunity of sensor Vibration
30s time out for IRON in static horizontal position
8min/10min/15min time out for IRON in static
vertical position
These chips are equipped with on-chip shunt
regulator, sensor signal processor, build-in oscillator,
timer, logic control, power on reset and output driving
block etc.
LED to indicate operation status
Usable in both 120V and 240V voltage supply
system
Applications
Quick function test mode
Electric Iron Controller
Support buzzer
Pin Assignment
Relay off and LED keeps on until movement
sensor be detected after power on
Few external components
DISC/BUZ
RELAY
LED
1
2
3
4
8
7
6
5
VCC
System standby mode power dissipation less than
1W (Base on recommended application circuits)
DIP-8 and SOIC-8 package
ACCLK
SW
Patent No: ZL 2005 2 0048330.4
GND
TEST
Pin Description
Pin No.
Pin Name
DISC/BUZ
RELAY
LED
I/O
O
Description
Discharge the external electrolytic cap to stabilize and limit its voltage. Output
4KHz to driver buzzer when timer is out. Active high.
Relay drive output, active high.
1
2
3
O
With open drain output, it can shut off external LED in parallel with this open-drain
transistor, active low.
O
4
5
6
7
8
GND
TEST
SW
-
I
I
I
-
Ground.
Low for test mode*.
Sensor signal input, input high will be considered horizontal.
AC 60/50Hz signal for clock with Schmitt architecture, internal drop down.
Power supply.
ACCLK
VCC
*Note: Teat mode comparison table:
Real timer
Test timer
30s
3s
8min
9.6s
10min
9.6s
15min
12s
12-07-0006
PT0336-1 07/06/12
1
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Block Diagram
VCC
GND
Sensor signal
processor
Power on
reset
SW
SWO
RELAY
Logic Control
Circuit
LED
DISC/BUZ
ACCLK
TEST
System
oscillator
30s/8/10/15min
Timer
Maximum Ratings
Note:
Storage Temperature………………………………………… - 40oC to +125oC
Supply Voltage to Ground Potential (Inputs & VCC only)….. - 0.5 to VCC +0.5V
Supply Voltage to Ground Potential (Outputs & D/O only)... - 0.5 to VCC +0.5V
DC Input Voltage …………………………………………...- 0.5V to VCC +0.5V
DC Output Current ………………………………………………………..20mA
Power Dissipation………………………………………………………..500mW
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure
to absolute maximum rating conditions for extended
periods may affect reliability.
Recommended Operating Conditions
Symbol
Description
Min
4.5
Typical
Max
5.5
Unit
V
VCC
Supply voltage
Operating Temperature
5
TA
-10
25
85
C
Electrical Characteristics (TA = -10 ~ 85ºC, unless otherwise noted)
Test Conditions
Sym
Parameter
Min
Typ
Max
Unit
VCC
-
Condition
-
VCC
I IL1
I IL2
I IL3
I IH1
I IH2
I IH3
IOH1
Internal Shunt regulator voltage
Input low current(ACCLK)
Input low current(TEST)
Input low current(SW)
Input high current(ACCLK)
Input high current(ACSEL)
Input high current(SW)
4.5
-
-5
-
30
-
-
5
-
-
-
-
-
-
-
5.5
-1
-30
-1
100
30
1
V
5V
5V
5V
5V
5V
5V
5V
VIL=0V
VIL=0V
VIL=0V
VIH=5V
VIH=5V
VIH=5V
VOH1=2.5V
A
A
A
A
A
A
mA
Output Source Current (RELAY /DISC)
Output Sink Current
-0.3
-0.7
IOL1
5V
VOL1=0.5V
5
-
-
mA
(RELAY /DISC)
IOL2
ICC
VPOR
Output Sink Current (LED)
Power supply current
Power on reset voltage.
5V
4V
-
VOL2=0.5V
See Figure 3
-
10
-
1.6
-
-
-
-
mA
A
V
400
3.0
12-07-0006
PT0336-1 07/06/12
2
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Functional Description (Refer to Block Diagram)
The chip is comprised of several blocks: on-chip shunt regulator, sensor signal processor, build-in system oscillator,
30s/8min/10min/15min timer, logic control circuit, and power on reset, etc. Each block will be described as below.
Logic control circuit
Logic control circuit mainly carries out logic control function. It not only collects signals from other blocks, but also generates
various driving signals including RELAY&DISC. Besides, an external LED will flash at about 1Hz and a buzzer will make a
sound with a frequency of 4KHz every 0.5s for 6 times or continual after internal timer times out. Signals at RELAY will control
external relay to decide whether IRON heats or not.
Sensor signal processor
The core in the whole system is how to correctly detect the position and movement of sensor so that the system can be always
under safe control. Thus, it is critical to accurately and correctly deal with signal from sensor in different status and eliminate the
noise caused by debounce action from sensor. Here, a unique structure is used to do the high-requirement signal processing.
In real application of IRON, sensor needs to be installed according to certain requirements (for example its inclination).
Timer
Timer block mainly generates various timing signal according to the position of IRON.
It is easy to get accurate timer (30s/8min/10min/15min) by using AC 60Hz/50Hz signal as timing reference. As above description,
Iron in Horizontal position over 30s will stop heating. While Iron in vertical position over 8min/10min/ 15min will also stop
heating.
Buzzer
A buzzer will make 0.5S sound with a frequency of 4 KHz for 6 times or continual after internal timer timeouts.
LED
Whenever power on or heating, LED pin is floating and an external LED will turn on. After times out, LED pin outputs pulse and
an external LED will flash at about 1Hz.
12-07-0006
PT0336-1 07/06/12
3
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Application Circuit
Note: Suggest the parameters of relay meet the following specification: 24VDC, 1.6KΩ Coil resistance
R1
R2
R4
D1
12K
15K
100K
C3
104
1N4007
240VAC
R3
10K
C2
22uF/16V
D2
1N4148
OUT
J1
RELAY
2N5551
Q2
2N5551
Q1
R6
1M
R5
100K
C1
10uF/100V
IC1
DISC/BUZ
1
2
3
4
8
7
6
5
VCC
ACCLK
SW
RELAY
LED
LED
R7
51.K
C4
103
GND
TEST
240VAC
SENSOR
Figure 1 Typical Application Circuit of PT8A351XC 240V
R1
R3
D1
VCC
100K
C3
104
6.8K
1N4007
C2
22uF/16V
120VAC
R2
10K
D2
1N4148
OUT
J1
RELAY
2N5551
Q2
R5
510K
R6
100K
2N5551
Q1
IC1
C1
10uF/100V
1
2
3
4
8
7
6
5
DISC/BUZ
RELAY
LED
VCC
ACCLK
SW
R7
51K
C4
103
GND
TEST
LED
120VAC
SENSOR
Figure 2 Typical Application Circuit of PT8A351XD 120V
12-07-0006
PT0336-1 07/06/12
4
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
D1
R1
R2
D2
12K
15K
BUZ
240VAC 1N4007
Infrared LED
R3*
1.8K
D2
1N4148
R5
100K
20mm
R4*
8.2K
OUT
J1
RELAY
C3
C2
104
C1
R7
1M
22uF/16V
2N5551
Q2
10uF/100V
R6
51K
2N5551
Q1
IC1
1
2
3
4
8
DISC/BUZ
RELAY
LED
VCC
7
6
5
ACCLK
SW
C4
D3
R8
GND
TEST
103
51K
LED
Photo Diode
240VAC
Figure 3 Typical Application Circuit of PT8A351XC 240V
D1
R1
D2
6.8K
1N4007
BUZ
120VAC
R2*
1.8K
Infrared LED
R4
100K
D2
1N4148
20mm
VCC
R3*
8.2K
OUT
J1
RELAY
C3
104
C2
C1
22uF/16V
R6
510K
2N5551
Q2
10uF/100V
R5
51K
2N5551
Q1
IC1
1
2
3
4
8
DISC/BUZ
RELAY
LED
VCC
7
6
5
ACCLK
SW
C4
D3
R8
GND
TEST
103
51K
LED
120VAC
Photo Diode
Figure 4 Typical Application Circuit of PT8A351XD 120V
12-07-0006
PT0336-1 07/06/12
5
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Mechanical Information
PE (DIP-8)
Dimensions In Millimeters
Symbol
Min
3.710
0.510
3.200
0.380
Max
4.310
A
A1
A2
B
3.600
0.570
B1
c
1.524 BSC
2.540 BSC
0.204
9.000
6.200
0.360
9.400
6.600
D
E
E1
e
7.320
7.920
Note:
1) Controlling dimensions in millimeters.
2) Ref: JEDEC MS-001D/BA
L
E2
3.000
8.400
3.600
9.000
12-07-0006
PT0336-1 07/06/12
6
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
WE (SOIC-8)
Dimensions In Millimeters
Symbol
Min
1.350
0.100
1.350
0.330
0.170
4.700
3.800
5.800
Max
1.750
0.250
1.550
0.510
0.250
5.100
4.000
6.200
A
A1
A2
b
Note:
c
D
1) Controlling dimensions in millimeters.
2) Ref: JEDEC MS-012E/AA
E
E1
e
L
θ
1.27 BSC
0.400
0°
1.270
8°
12-07-0006
PT0336-1 07/06/12
7
PT8A3514/15/16/17/18/19(C/D)
Smart Iron Controller
||||||||||||||||
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Ordering Information
Part Number
PT8A351xCPE
PT8A351xCPE
PT8A351xDWE
Package Code
Package
P
P
Lead free DIP-8
Lead free DIP-8
W
W
Lead free and Green SOIC-8
Lead free and Green SOIC-8
PT8A351xDWE
Note:
“x” shows different function. Pls see below Function comparison table for details.
E = Pb-free or Pb-free & Green
Adding X Suffix= Tape/Reel
Function comparison table
Part Number
PT8A 3514C
PT8A 3515C*
PT8A 3516C*
PT8A 3517C*
PT8A 3518C*
PT8A 3519C*
PT8A 3514D*
PT8A 3515D*
PT8A 3516D*
PT8A 3517D*
PT8A 3518D*
PT8A 3519D*
Frequency
Vertical Timer
10min
8min
Horizontal timer
Buzzer
Continual
Stop after 6 times
Stop after 6 times
Continual
Continual
Stop after 6 times
Continual
Stop after 6 times
Stop after 6 times
Continual
Continual
Stop after 6 times
50Hz
50Hz
50Hz
50Hz
50Hz
50Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
30s
30s
30s
30s
30s
30s
30s
30s
30s
30s
30s
30s
15min
8min
15min
10min
10min
8min
15min
8min
15min
10min
Note:
*Contact Pericom for availability.
Pericom Semiconductor Corporation 1-800-435-2336 www.pericom.com
Pericom reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply
the best possible product. Pericom does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom product. The
company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom.
12-07-0006
PT0336-1 07/06/12
8
相关型号:
©2020 ICPDF网 联系我们和版权申明