ST1318BAB-FREQ1 [PERICOM]
HCMOS/TTL Output Clock Oscillator, 32MHz Min, 80MHz Max,;型号: | ST1318BAB-FREQ1 |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | HCMOS/TTL Output Clock Oscillator, 32MHz Min, 80MHz Max, |
文件: | 总2页 (文件大小:119K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SaRonix
Voltage Controlled Crystal Oscillator 3.3 & 5V, HCMOS, SMD
S1318 / S1518 Series
Technical Data
Frequency Range:
32 MHz to 125 MHz
Frequency Stability:
50 ppm over all conditions: operating temperature, voltage change,
load change, calibration tolerance, aging, with V = 2.5V @ 5V,
C
V
= 1.65V @ 3.3V
C
Temperature Range:
Operating:
Storage:
0 to +70°C, -40 to +85°C
-55 to +125°C
Supply Voltage:
Recommended Operating:
+5 VDC 5% or 3.3V 10%
Supply Current:
32 to 70 MHz:
70+ to 125 MHz:
50mA max, 35mA max @ 3.3V
65mA max, 35mA max @ 3.3V
ACTUAL SIZE
Output Drive:
Symmetry:
45/55% @50% V
3.3V version 0 to +70°C only
DD,
40/60% @1.4V level, 3.3V version @50% V
Description
-40 to +85°C
DD,
1.5ns max @5V with TTL load only
Rise & Fall Times:
Logic 0:
4ns max 20 to 80% V
DD,
0.5V max, 20% V
2.5V min, 80% V
A voltage controlled, low current crystal
oscillator, providing precise rise and fall
times to drive high performance applica-
tions. The device is packaged in a 6-pin,
SMD,J-leadedpackage.Theplasticmold-
edsurfacemountablepackageisidealfor
today's automated assembly environ-
ments.
max @3.3V
max @3.3V
DD
DD
Logic 1:
Load:
50pF or 5TTL 32 to 50 MHz, 30pF up to 80 MHz @ 3.3V
30pF or 5TTL 50+ to 120 MHz, 95Ω AC up to 125 MHz @ 3.3V
20ps max
Period Jitter RMS:
Pull Characteristics:
Input Impedance:
Frequency Response (-3dB):
Pullability:
50KΩ min
50 kHz min
25, 50, 75 ppm APR* (See Part Numbering ꢀuide)
0.5 to 4.5V, 0.3 to 3.0V
Applications
Control Voltage:
Transfer Function:
Linearity:
Center Control Voltage:
Frequency Increases when Control Voltage Increases
10% max
2.5V @ 5V or 1.65V @ 3.3V
• For use in phase-locked loop (PLL)
clock and data recovery, frequency
translation, or frequency synthesis ap-
plicationsinvideo, videocompression,
telephony, and LAN/WAN data com-
munication environments.
Phase Noise:
-95 dBc/Hz @ 100 Hz
-110 dBc/Hz @ 1 kHz
-100 dBc/Hz @ 10 kHz
• High and wide frequency range from
32 MHz to 125 MHz
ˆ 3.3 or 5 Volt operation
Mechanical:
Shock:
Solderability:
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 2003
Terminal Strength:
Vibration:
Solvent Resistance:
Resistance to Soldering Heat:
MIL-STD-202, Method 211, Conditions A & C
MIL-STD-883, Method 2007, Condition A
MIL-STD-202, Method 215
• Compact,plasticmoldedsurfacemount
package
• HCMOS and TTL compatible
• Tri-state output
MIL-STD-202, Method 210, Condition I or J
• Available on tape & reel; 24mm tape,
500pcs per reel
Environmental:
Thermal Shock:
Moisture Resistance:
MIL-STD-883, Method 1011, Condition A
MIL-STD-883, Method 1004
Output Waveform
Solder Reflow Guide
HCMOS
Tr
Tf
Reflow 240°C max
Cooling
250
4°C/sec max
Preheat 183 10°C
1 LEVEL
80% VDD
50% VDD
20% VDD
0 LEVEL
200
150
4°C/sec max
Time
1 – 2 minutes
10 sec max
SYMMETRY
* APR = (VCXO Pull relative to specified Output Freq. @
nominal control voltage) – (VCXO Freq. Stability)
DS-171 REV C
141 Jefferson Drive • Menlo Park, CA 94025 • USA • 650-470-7700 • 800-227-8974 • Fax 650-462-9894
SaRonix
SaRonix
Voltage Controlled Crystal Oscillator 3.3 & 5V, HCMOS, SMD
S1318 / S1518 Series
Technical Data
Tri-State Logic Table
Part Numbering Guide
S
T
1518
E
G
B
-
32.0000 (T)
Pin 2 Input
Logic 1 or NC
Logic 0 or GND
Pin 4 Output
Model
Output
T = Tri-State
Blank = non Tri-State
Series
Oscillation
(T) = Tape & Reel
full reel increments onlꢀ
High Impedance
Frequency (MHz)
Required Input Levels on Pin 2:
Logic 1 = 3.0V min
Logic 0 = 0.5V or 0.3V max
Linearity
B = 10%
S1318 = 3V, HCMOS/TTL, SMD VCXO
S1518 = 5V, HCMOS/TTL, SMD VCXO
Pullability (Minimum APR)
A = 50 ppm
G = 25 ppm
H = 75 ppm, 5V onlꢀ
*
Stability Tolerance
B = 50 ppm, 0 to +70°C
E = 50 ppm, -40 to +85°C
Package Details
6
5
4
* APR = (VCXO Pull relative to specified Output Freq. @ nominal control voltage) – (VCXO Freq. Stability)
DENOTES
PIN 1
SARONIX YYWW
32.0000 MHZ
PART #
Test Circuits:
10.4
.409
8.74
.344
max
TEST POINT
mA
M
1
2
3
Pin 6
Pin 1
Pin 5
Pin 4
13.2
.520
max
OSCILLATOR
Pin 2
6.1
5.9
.234
POWER
SUPPLY
max
.240
0.1µF
C
= 50pF: 32 to 50 MHz
30pF: 50+ to 125 MHz
(Note A)
L
Pin 3
0.46
.018
V C
2.54
.100
5.08
.200
0.51
.020
x45° CHAM
TRI-STATE INPUT or ENABLE/DISABLE
(current limited on fixture)
.75
.030
NOTE A: C includes probe and jig capacitance.
L
1.50 .15
.059 .006
8.74
.344
SIMULATED TEST LOAD
V
CC
Pin Functions:
TEST POINT
Pin 1: Control Voltage
Pin 2: Tri-State Control
Pin 3: GND
Pin 4: Output
Pin 5: N/C
780
Ω
mA
M
Pin 6: V
CC
Pin 6
Pin 1
Pin 5
Pin 4
Pin 3
mm
Scale: None (Dimensions in
)
inches
OSCILLATOR
Pin 2
Recommended Land Pattern
POWER
SUPPLY
0.1µF
C = 15pF
L
(Note A)
5.08
.200
V C
8.62
1.27
.339
.050
2.5
.100
TRI-STATE INPUT or ENABLE/DISABLE
(current limited on fixture)
2.54
.100
NOTE A: C includes probe and jig capacitance.
L
All specifications are subject to change without notice.
DS-171 REV C
SaRonix
141 Jefferson Drive • Menlo Park, CA 94025 • USA • 650-470-7700 • 800-227-8974 • Fax 650-462-9894
相关型号:
©2020 ICPDF网 联系我们和版权申明