POE30U-560 [PHIHONG]
30W Power Over Ethernet Adapter; 30W以太网供电适配器
| 型号： | POE30U-560 |
| 厂家： | 
PHIHONG USA INC. |
| 描述： | 30W Power Over Ethernet Adapter |
| 文件： | 总3页 (文件大小：92K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
WWW.PHIHONG.COM
30W Power Over Ethernet Adapter
High Power single port injector.
Features
•
Fully Compliant detection, disconnect and
voltage control IEEE802.3af
•
UNH IOL Tested
•
•
Diagnostic LEDs
Non-Vented Case
•
•
Full Protection OCP, OVP
Gigabit Compatible
Applications
•
•
•
IP Telephones
Wireless Network Access Points
Blue Tooth Access Point
•
•
Security Camera
IP Print Servers
Safety Approvals
•
•
cUL/UL
CE
•
TUV
Mechanical Characteristics
•
•
Length: 140mm (5.51in)
Width: 65mm (2.55in)
•
•
Height: 36mm (1.42in)
Weight: 0.2Kg (0.44lb.)
Output Specifications
DC Output
Voltage
Load
Min.
Regulation
Model
Line
Load
Max.
POE30U-560
56V
0A
0.55A
54-57Vdc under all conditions
Ripple And Noise*
<500Hz
Vp-p*
0.5
500Hz-150KHz
150KHz-500KHz
500KHz-1MHz
0.15
0.15
0.1
*As per IEEE802.3af Table 33-5.
Phihong is not responsible for any error and change. Content is subject to change without notice. Please consult the factory and
visit www.phihong.com for the most up-to-date specifications.
POE30U Characteristics
WWW.PHIHONG.COM
INPUT:
AC Input Voltage Range
90 to 264VAC
EMC
FCC Part 15 Class B
EN55022 Class B
AC Input Voltage Rating
100 to 240VAC,47-63Hz
Isolation Test
Primary to Secondary: 3000VAC for 1 minute 10mA
Primary to F.G.: 1500VAC for 1 minute
Output to F.G.: 1500VAC
AC Input Current
0.5A(RMS) max. for 90VAC
0.35A(RMS) max. for 240VAC
Immunity
ESD:
EN61000-4-2. Level 3
EN61000-4-3. Level 2
EN61000-4-4. Level 2
EN61000-4-5. Level 3
EN61000-4-6. Level 2
EN61000-4-11
Leakage Current
1.0mA max. @ 254VAC 60Hz
RS:
EFT:
Surge:
CS:
Voltage Dips
Harmonic:
AC Inrush Current
15A(RMS) max. for 115VAC
20A(RMS) max. for 230VAC
EN61000-3-2
OUTPUT:
Total Output Power
30W
Insulation Resistance
Primary to secondary: >10M OHM 500VDC
Primary to FC: >10M OHM 500VDC
DC Offset
FEATURE:
No Data degradation with DC imbalance 18mA
Over Voltage/Current, Short Circuit Protection
Outputs equipped with short circuit protection and overload
protection as per 802.3af specification except max average
current is 0.55A, Peak 0.6A
Efficiency
65% (typical) at Max. load, and 120VAC 60Hz
The output can be shorted permanently without damage
Hold-up Time
16mS min. 120VAC and max. load
Indicators
Led #1 indicator for input power “on” GREEN
Led #2 Indicator for fault-RED
Led #3 Indicator that Detected and Connected to valid
IEEE802.3af load-GREEN
Transient O/P Voltage Protection
60V max.
ENVIRONMENTAL:
Temperature
Input Connector
IEC320 inlet 3 pin
Operation
0 to +40°C
Non-operation
-25 to +65°C
Output Connection
+pins 3,6
- pins 1,2
Humidity
Operation
5 to 90%
Dimension Diagram Unit: mm (inch)
Gigabit Power Injector Block Diagram
Description of LED Functions for Gigabit Power Injector
Power-up Sequence:
Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor
software. After the end of the 2 seconds, the "ON" LED will illuminate green, signifying that the DC
output voltage is available for powering a compliant load (to the 802.3af PoE standards).
Detection Sequence:
Once a compliant load is attached to the output RJ45 connector, the green "CONNECT" LED will
illuminate.
Should the load be non-compliant then the LEDs will blink a code signifying the cause for non-detection.
Detection Failure Codes:
1. Incorrect resistive signature – The green “CONNECT” and red “FAULT” LEDs will blink 3 times.
2. Incorrect capacitive signature – The green “ON” LED will blink 3 times.
3. Incorrect Voffset – The green “CONNECT” and green “ON” LEDs will blink 3 times.
4. Unstable current measurement – The green “CONNECT” LED will blink 3 times
5. Low voltage sensed during detection (overload) – The red “FAULT” LED will blink 3 times
After the LEDs blink 3 times the PSE will continue to try to detect a valid load. Therefore, until the
correct load is applied, the LEDs will continue to blink. If there is an open circuit connected to the output
RJ45 then the LEDs will not blink but the PSE will continue to try to detect a valid load.
Fault Sequence:
Should there be a fault such as an overload or short circuit then the red "FAULT" LED will illuminate.
The red “FAULT” LED will illuminate for 2 seconds and then go off as the power supply tries to re-
detect a valid load. If there is a problem in detecting, the LED will indicate what is wrong with the load
as per the codes in the section above.
相关型号：
©2020 ICPDF网 联系我们和版权申明