MC33662JEF
更新时间:2024-09-18 14:24:53
品牌:NXP
描述:Transceiver, Physical Layer, LIN 2.1 / SAEJ2602-2, 10kbps, SOIC 8, Rail
MC33662JEF 概述
Transceiver, Physical Layer, LIN 2.1 / SAEJ2602-2, 10kbps, SOIC 8, Rail 接口芯片 网络接口
MC33662JEF 规格参数
是否无铅: | 不含铅 | 是否Rohs认证: | 符合 |
生命周期: | Transferred | 零件包装代码: | SOIC |
包装说明: | 4 X 5 MM, 1.27 MM PITCH, ROHS COMPLIANT, SOIC-8 | 针数: | 8 |
Reach Compliance Code: | unknown | ECCN代码: | EAR99 |
HTS代码: | 8542.39.00.01 | 风险等级: | 5.67 |
JESD-30 代码: | R-PDSO-G8 | JESD-609代码: | e3 |
长度: | 4.9 mm | 湿度敏感等级: | 3 |
功能数量: | 1 | 端子数量: | 8 |
最高工作温度: | 125 °C | 最低工作温度: | -40 °C |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | SOP |
封装形状: | RECTANGULAR | 封装形式: | SMALL OUTLINE |
峰值回流温度(摄氏度): | 260 | 认证状态: | Not Qualified |
座面最大高度: | 1.75 mm | 标称供电电压: | 13.5 V |
表面贴装: | YES | 电信集成电路类型: | INTERFACE CIRCUIT |
温度等级: | AUTOMOTIVE | 端子面层: | Matte Tin (Sn) |
端子形式: | GULL WING | 端子节距: | 1.27 mm |
端子位置: | DUAL | 处于峰值回流温度下的最长时间: | 40 |
宽度: | 3.9 mm | Base Number Matches: | 1 |
MC33662JEF 数据手册
通过下载MC33662JEF数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Document Number: MC33662
Rev. 7.0, 1/2014
escale Semiconductor
Advance Information
LIN 2.1 / SAEJ2602-2, LIN
Physical Layer
33662
The Local Interconnect Network (LIN) is a serial communication
protocol, designed to support automotive networks in conjunction with
a Controller Area Network (CAN). As the lowest level of a hierarchical
network, LIN enables cost-effective communication with sensors and
actuators when all the features of CAN are not required.
LINCELL
The three 33662 versions are designed to operate at different
maximum baud rates. The 33662LEF and 33662BLEF, and the
33662SEF and 33662BSEF, offer a normal baud rate (20 kbps), and
the 33662JEF and 33662BJEF, a slow baud rate (10 kbps). They
integrate a fast baud rate (above 100 kbps), as reported by the RXD pin
for test and programming modes. They provide excellent EMC
(Electromagnetic Compatibility) and Radiated Emission performance,
ESD (Electrostatic Discharge) robustness, and safe behavior, in the
event of a LIN bus short-to-ground, or a LIN bus leakage during low-
power mode. This device is powered by SMARTMOS technology.
Features
EF SUFFIX (PB-FREE)
98ASB42564B
• Operational from a VSUP of 7.0 to 18 V DC, functional up to 27 V DC,
and handles 40 V during Load Dump
8-PIN SOICN
• Compatible with LIN Protocol Specification 1.3, 2.0, 2.1, and
SAEJ2602-2
• Active bus wave shaping, offering excellent radiated emission
performance
Applications
• Automotive Market:
• Body electronics (BCM, gateway, roof, door,
lighting, HVAC)
• Powertrain (EMS, start & stop), BMS
• Safety & Chassis (TPMS, seat belt)
• Sustains up to 15.0 kV minimum ESD IEC61000-4-2 on the LIN Bus,
20 kV on the WAKE pin, and 25 kV on the VSUP pin
• Very high immunity against electromagnetic interference
• Low standby current in Sleep mode
• Overtemperature protection
• Local and remote Wake-up capability reported by the RXD pin
• Fast baud rate selection reported by RXD pin
• 5.0 V and 3.3 V compatible digital inputs without any required
external components
VBAT
33662
VSUP
WAKE
CAN SBC
or
VDD
MCU
Regulator
INH
LIN
EN
12 V
RXD
TXD
LIN Interface
5.0 V
or 3.3 V
GND
Figure 1. 33662 Master LIN Bus Simplified Application Diagram
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© Freescale Semiconductor, Inc., 2011-2014. All rights reserved.
DEVICE VARIATIONS
DEVICE VARIATIONS
Table 1. Device Variations
Freescale Part No.
(Add an R2 suffix for Tape and Reel
orders)
Temperature Range (T )
Package
Maximum Baud Rate
A
MC33662LEF (1)
MC33662BLEF
20 kbps
MC33662SEF (1)
MC33662BSEF
20 kbps with restricted limits for
transmitter and receiver symmetry
-40 to 125 °C
8 SOICN
MC33662JEF (1)
MC33662BJEF
10 kbps
Notes
1. In Sleep mode, the total module current consumption may be higher than expected if the external pull-up resistor on the RxD pin
is implemented. There may be an unexpected glitch on RxD as INH goes low.
33662
Analog Integrated Circuit Device Data
2
Freescale Semiconductor
INTERNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
VSUP
X 1
INH_ON
INH
LIN
EN
EN-SLEEP
200 k
Control Unit
30 k
725 k
RXD
RXD_INT
Receiver
EN_RXD
LIN_EN
Slope
Control
TXD_INT
TXD
WAKE
GND
Figure 2. 33662 Simplified Internal Block Diagram
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
PIN CONNECTIONS
PIN CONNECTIONS
RXD
1
2
3
4
INH
8
7
VSUP
EN
WAKE
TXD
LIN
6
5
GND
Figure 3. 33662 8-SOICN Pin Connections
Table 2. 33662 8-SOICN Pin Definitions
A functional description of each pin can be found in the Functional Pin Description section beginning on page 21.
Pin
PIN NAME Pin Function
Formal Name
Definition
This pin is the receiver output of the LIN interface which reports the state
of the bus voltage to the MCU interface.
1
RXD
Output
Data Output
This pin controls the operation mode of the interface.
2
3
EN
Input
Input
Enable Control
Wake Input
This pin is a high-voltage input used to wake-up the device from Sleep
mode.
WAKE
This pin is the transmitter input of the LIN interface which controls the
state of the bus output.
4
TXD
Input
Data Input
This pin is the device ground pin.
5
6
GND
LIN
Ground
Ground
LIN Bus
This bidirectional pin represents the single-wire bus transmitter and
receiver.
Input/Output
This pin is the device battery level power supply.
7
8
VSUP
INH
Power
Output
Power Supply
Inhibit Output
This pin can have two main functions: controlling an external switchable
voltage regulator having an inhibit input, or driving an external bus
resistor in the master node application.
33662
Analog Integrated Circuit Device Data
4
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
Unit
ELECTRICAL RATINGS
Power Supply Voltage
Normal Operation (DC)
V
V
-0.3 to 27
SUP(SS)
Transient input voltage with external component (according to ISO7637-2 & ISO7637-
3 & “Hardware Requirements for LIN, CAN and Flexray Interfaces in Automotive
Applications” specification Rev1.1 / December 2nd, 2009) (See Table 4 and Figure 4)
- Pulse 1 (test up to the limit for Damage - Class A(2)
)
V
-100
+75
SUP(S1)
SUP(S2A)
SUP(S3A)
SUP(S3B)
SUP(S5B)
- Pulse 2a (test up to the limit for Damage - Class A(2)
- Pulse 3a (test up to the limit for Damage - Class A(2)
- Pulse 3b (test up to the limit for Damage - Class A(2)
- Pulse 5b (Class A)(2)
)
)
)
V
V
V
V
-150
+100
-0.3 to 40
WAKE
Normal Operation within series 2*18 k resistor (DC)
V
V
-27 to 40
WAKE(SS)
Transient input voltage with external component (according to ISO7637-2 & ISO7637-
3 & “Hardware Requirements for LIN, CAN and Flexray Interfaces in Automotive
Applications” specification Rev1.1 / December 2nd, 2009) (See Table 4 and Figure 5)
- Pulse 1 (test up to the limit for Damage - Class D(3)
)
V
-100
+75
WAKE(S1)
- Pulse 2a (test up to the limit for Damage - Class D(3)
- Pulse 3a (test up to the limit for Damage - Class D(3)
)
)
)
V
V
V
WAKE(S2A)
WAKE(S3A)
WAKE(S3B)
-150
+100
- Pulse 3b (test up to the limit for Damage - Class D(3)
Logic Voltage (RXD, TXD, EN Pins)
LIN Bus Voltage
V
-0.3 to 5.5
V
V
LOG
Normal Operation (DC)
V
-27 to 40
BUS(SS)
Transient (Coupled Through 1.0 nF Capacitor, according to ISO7637-2 & ISO7637-3
& “Hardware Requirements for LIN, CAN and Flexray Interfaces in Automotive
Applications” specification Rev1.1 / December 2nd, 2009) (See Table 4 and Figure 6)
- Pulse 1 (test up to the limit for Damage - Class D(3)
)
V
-100
+75
BUS(S1)
- Pulse 2a (test up to the limit for Damage - Class D(3)
- Pulse 3a (test up to the limit for Damage - Class D(3)
)
)
)
V
V
V
BUS(S2A)
BUS(S3A)
BUS(S3B)
-150
+100
- Pulse 3b (test up to the limit for Damage - Class D(3)
INH Voltage/Current
DC Voltage
V
V
-0.3 to V
+0.3
SUP
INH
Transient (Coupled Through 1.0 nF Capacitor, according to ISO7637-2 & ISO7637-3
& “Hardware Requirements for LIN, CAN and Flexray Interfaces in Automotive
Applications” specification Rev1.1 / December 2nd, 2009) (See Table 4 and Figure 7)
- Pulse 1 (test up to the limit for Damage - Class D(3)
)
V
-100
INH(S1)
INH(S2A)
INH(S3A)
INH(S3B)
- Pulse 2a (test up to the limit for Damage - Class D(3)
- Pulse 3a (test up to the limit for Damage - Class D(3)
- Pulse 3b (test up to the limit for Damage - Class D(3)
)
)
)
V
V
V
+75
-150
+100
Notes
2. Class A: All functions of a device/system perform as designed during and after exposure to disturbance.
3. Class D: At least one function of the transceiver stops working properly during the test, and will return to proper operation automatically
when the exposure to the disturbance has ended. No physical damage of the IC occurs.
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 3. Maximum Ratings (continued)
All voltages are with respect to ground, unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
ELECTRICAL RATINGS (CONTINUED)
Symbol
Value
Unit
ESD Capability - AECQ100
V
Human Body Model - JESD22/A114 (C
= 100 pF, R
= 1500 )
ZAP
ZAP
V
V
V
±10.0 k
±8.0 k
±4.0 k
ESD1-1
ESD1-2
ESD1-4
LIN pin versus GND
Wake pin versus GND
All other pins
Charge Device Model - JESD22/C101 (C
= 4.0 pF
ZAP
V
V
±750
±500
Corner pins (Pins 1, 4, 5 and 8)
All other pins (Pins 2, 3, 6 and 7)
ESD2-1
ESD2-2
Machine Model - JESD22/A115 (C
All pins
= 220 pF, R
= 0 )
ZAP
ZAP
V
±200
ESD3-1
According to “Hardware Requirements for LIN, CAN and Flexray Interfaces in
Automotive Applications” specification Rev1.1 / December 2nd, 2009 (C = 150 pF,
ZAP
R
= 330 )
ZAP
Contact Discharge, Unpowered
LIN pin without capacitor
LIN pin with 220 pF capacitor
VSUP (10 µF to ground)
WAKE (2*18 k serial resistor)
INH pin
V
V
V
V
V
V
±15 k
±15 k
±25 k
±20 k
±2.0 k
>±15 k
ESD4-1
ESD4-2
ESD4-3
ESD4-4
ESD4-5
ESD4-6
LIN pin with 220 pF capacitor and indirect ESD coupling (according to ISO10605
- Annex F)
According to ISO10605 - Rev 2008 test specification
(2.0 k / 150 pF) - Unpowered - Contact discharge
LIN pin without capacitor
V
V
V
V
±20 k
±25 k
±25 k
±25 k
ESD5-1
ESD5-2
ESD5-3
ESD5-4
LIN pin with 220 pF capacitor
VSUP (10 µF to ground)
WAKE (2*18 k serial resistor)
(2.0 k / 330 pF) - Powered - Contact discharge
LIN pin without capacitor
±8 k
±10 k
±12 k
±15 k
V
V
V
V
ESD6-1
ESD6-2
ESD6-3
ESD6-4
LIN pin with 220 pF capacitor
VSUP (10 µF to ground)
WAKE (2*18 k serial resistor)
THERMAL RATINGS
Operating Temperature
C
T
A
-40 to 125
-40 to 150
Ambient
Junction
T
J
Storage Temperature
TSTG
RJA
-40 to 150
150
C
°C/W
°C
Thermal Resistance, Junction to Ambient
Peak Package Reflow Temperature During Solder Mounting (4)
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis Temperature
Notes
T
240
SOLDER
T
150 to 200
20
°C
SHUT
HYST
T
°C
4. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
33662
Analog Integrated Circuit Device Data
6
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 4. Limits / Maximum Test Voltage for Transient Immunity Tests
Pulse repetition
Test Pulse
VS [V]
frequency [Hz] Test Duration [min]
(1/T1)
Ri []
Remarks
1
-100
+75
2
10
2
t2 = 0 s
1 for function test
10 for damage test
2a
3a
3b
2
-150
+100
10000
10000
50
50
DUT
Transient Pulse
Generator
(Note)
VSUP
D1
10 µF
GND
DUT GND
Note Waveform per ISO 7637-2. Test Pulses 1, 2a, 3a, 3b.
Figure 4. Test Circuit for Transient Test Pulses (VSUP)
DUT
Transient Pulse
Generator
(Note)
1.0 nF
WAKE
18 k
18 k
GND
DUT GND
Note Waveform per ISO 7637-2. Test Pulses 1, 2a, 3a, 3b.
Figure 5. Test Circuit for Transient Test Pulses (WAKE)
DUT
Transient Pulse
Generator
(Note)
1.0 nF
LIN
GND
DUT GND
Note Waveform per ISO 7637-2. Test Pulses 1, 2a, 3a, 3b.
Figure 6. Test Circuit for Transient Test Pulses (LIN)
DUT
Transient Pulse
Generator
(Note)
1.0 nF
INH
GND
DUT GND
Note Waveform per ISO 7637-2. Test Pulses 1, 2a, 3a, 3b.
Figure 7. Test Circuit for Transient Test Pulses (INH)
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 5. Static Electrical Characteristics
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
VSUP PIN (DEVICE POWER SUPPLY)
Symbol
Min
Typ
Max
Unit
Nominal Operating Voltage
V
7.0
6.7
–
13.5
–
18.0
27
V
V
V
V
SUP
Functional Operating Voltage(5)
Load Dump
VSUPOP
VSUPLD
VPOR
–
40
Power-On Reset (POR) Threshold
VSUP Ramp Down and INH goes High to Low
3.5
–
–
5.3
–
Power-On Reset (POR) Hysteresis
VPORHYST
270
mV
V
V
Undervoltage Threshold (positive and negative)
VUVL, VUVH
SUP
Transmission disabled and LIN bus goes in recessive state
Undervoltage Hysteresis (VUVL - VUVH
5.8
–
–
6.7
–
V
)
VUVHYST
130
mV
SUP
Supply Current in Sleep Mode
13.5 V, Recessive State
A
V
I
—
—
—
6.0
—
11
20
70
SUP
S1
13.5 V < V
< 27 V
I
SUP
S2
I
24
V
13.5 V, Shorted to GND
S3
SUP
Supply Current in Normal or Slow or Fast Mode
Bus Recessive, Excluding INH Output Current
Bus Dominant, Excluding INH Output Current
mA
I
—
—
4.0
6.0
6.0
8.0
S(REC)
I
S(DOM)
RXD OUTPUT PIN (LOGIC)
Low Level Output Voltage
V
V
V
OL
I
1.5 mA
0
—
0.9
IN
High Level Output Voltage
V
OH
V
V
= 5.0 V, I
= 3.3 V, I
250 A
250 A
4.25
3.0
—
—
5.25
3.5
EN
EN
OUT
OUT
TXD INPUT PIN (LOGIC)
Low Level Input Voltage
High Level Input Voltage
Input Threshold Voltage Hysteresis
Pull-up Current Source
V
—
2.0
100
—
—
0.8
—
V
V
IL
V
IH
V
300
600
mV
A
INHYST
I
PU
V
= 5.0 V, 1.0 V < V
< 3.5 V
-60
-35
-20
EN
TXD
EN INPUT PIN (LOGIC)
Low Level Input Voltage
High Level Input Voltage
V
—
—
—
0.8
—
V
V
IL
V
2.0
100
100
IH
Input Voltage Threshold Hysteresis
Pull-down Resistor
V
400
230
600
350
mV
kohm
INHYST
RPD
5. For the functional operating voltage, the device is functional and all features are operating. The electrical parameters are noted under
conditions 7.0 V VSUP 18V, -40oC TA 125o C, GND = 0 V.
33662
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 5. Static Electrical Characteristics (continued)
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
LIN PHYSICAL LAYER - TRANSCEIVER LIN(6)
Operating Voltage Range(7)
Symbol
Min
Typ
Max
Unit
VBAT
VSUP
8.0
7.0
–
–
–
18
18
40
V
V
Supply Voltage Range
Voltage Range (within which the device is not destroyed)
VSUP_NON_OP
IBUS_LIM
-0.3
V
Current Limitation for Driver Dominant State
Driver ON, VBUS = 18 V
mA
40
-1.0
–
90
–
200
–
Input Leakage Current at the Receiver
Driver off; VBUS = 0 V; VBAT = 12 V
IBUS_PAS_DOM
mA
µA
Leakage Output Current to GND
IBUS_PAS_REC
Driver Off; 8.0 V VBAT 18 V; 8.0 V VBUS 18 V; VBUS VBAT;
VBUS VSUP
–
20
Control Unit Disconnected from Ground(8)
IBUS_NO_GND
mA
GNDDEVICE = VSUP; VBAT = 12 V; 0 < V
< 18 V
-1.0
–
1.0
BUS
V
Disconnected; VSUP_DEVICE = GND; 0 V < V
< 18 V(9)
BUS
IBUSNO_BAT
VBUSDOM
VBUSREC
–
–
–
–
–
10
0.4
–
µA
BAT
Receiver Dominant State(10)
Receiver Recessive State(11)
VSUP
VSUP
VSUP
0.6
Receiver Threshold Center
(VTH_DOM + VTH_REC)/2
VBUS_CNT
0.475
0.5
0.525
Receiver Threshold Hysteresis
VHYS
VSUP
(VTH_REC - VTH_DOM
)
–
–
0.175
LIN dominant level with 500 680 and 1.0 k load on the LIN bus
VLINDOM_LEVEL
VSHIFT_BAT
VSHIFT_GND
VBUSWU
–
0
–
–
0.25
11.5%
11.5%
5.3
VSUP
VBAT
VBAT
V
VBAT_SHIFT
GND_SHIFT
0
–
LIN Wake-up Threshold from Sleep Mode
–
4.3
30
LIN Pull-up Resistor to V
SUP
RSLAVE
20
60
k
LIN Internal Capacitor(12)
CLIN
30
pF
Overtemperature Shutdown(13)
Overtemperature Shutdown Hysteresis
TLINSD
150
–
160
20
200
–
°C
TLINSD_HYS
°C
Notes
6. Parameters guaranteed for 7.0 V VSUP 18 V.
7. Voltage range at the battery level, including the reverse battery diode.
8. Loss of local ground must not affect communication in the residual network.
9. Node has to sustain the current that can flow under this condition. The bus must remain operational under this condition.
10. LIN threshold for a dominant state.
11. LIN threshold for a recessive state.
12. This parameter is guaranteed by process monitoring but not production tested.
13. When an overtemperature shutdown occurs, the LIN transmitter and receiver are in recessive state and INH switched off. This parameter
is tested with a test mode on ATE and characterized at laboratory.
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 5. Static Electrical Characteristics (continued)
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
INH OUTPUT PIN
Driver ON Resistance (Normal Mode)
IINH = 50 mA
INH
ON
—
—
—
—
—
50
30
Current load capability
IINH_LOAD
mA
A
From 7.0 V < VSUP < 18 V
Leakage Current (Sleep Mode)
I
LEAK
0 < V
< V
SUP
-5.0
5.0
INH
Overtemperature Shutdown(14)
TINHSD
150
—
160
20
200
—
°C
°C
Overtemperature Shutdown Hysteresis
WAKE INPUT PIN
TINHSD_HYS
High to Low Detection Threshold (5.5 V < VSUP < 7 V)
Low to High Detection Threshold (5.5 V < VSUP < 7 V)
Hysteresis (5.5 V < VSUP < 7 V)
VWUHL1
VWULH1
VWUHYS1
VWUHL2
VWULH2
VWUHYS2
IWU
2.0
2.4
0.2
2.4
2.9
0.2
—
—
—
—
—
—
—
—
3.9
4.3
0.8
3.9
4.3
0.8
5.0
V
V
V
High to Low Detection Threshold (7 V VSUP < 27 V)
Low to High Detection Threshold (7 V VSUP < 27 V)
Hysteresis (7 V VSUP < 27 V)
V
V
V
Wake-up Input Current (VWAKE < 27 V)
µA
Notes
14. When an overtemperature shutdown occurs, the INH high side is switched off and the LIN transmitter and receiver are in recessive state.
This parameter is tested with a test mode on ATE and characterized at laboratory.
33662
Analog Integrated Circuit Device Data
10
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 6. Dynamic Electrical Characteristics
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
LIN PHYSICAL LAYER
(15) (16)
,
DRIVER CHARACTERISTICS FOR NORMAL SLEW RATE - 20.0 KBIT/SEC ACCORDING TO LIN PHYSICAL LAYER SPECIFICATION
33662L AND 33662S DEVICES
Duty Cycle 1:
D1
D2
THREC(MAX) = 0.744 * VSUP
THDOM(MAX) = 0.581 * VSUP
%
0.396
—
—
—
D1 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 50 µs, 7.0 V VSUP18 V
Duty Cycle 2:
THREC(MIN) = 0.422 * VSUP
THDOM(MIN) = 0.284 * VSUP
—
0.581
D2 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 50 µs, 7.6 V VSUP18 V
LIN PHYSICAL LAYER
(15) (16)
,
DRIVER CHARACTERISTICS FOR SLOW SLEW RATE - 10.4 KBIT/SEC ACCORDING TO LIN PHYSICAL LAYER SPECIFICATION
33662J DEVICE
Duty Cycle 3:
D3
THREC(MAX) = 0.778 * VSUP
THDOM(MAX) = 0.616 * VSUP
%
0.417
—
—
D3 = tBUS_REC(MIN)/(2 x tBIT), tBIT = 96 µs, 7.0 V VSUP18 V
Duty Cycle 4:
D4
THREC(MIN) = 0.389 * VSUP
THDOM(MIN) = 0.251 * VSUP
—
—
—
—
0.590
100
D4 = tBUS_REC(MAX)/(2 x tBIT), tBIT = 96 µs, 7.6 V VSUP18 V
LIN PHYSICAL LAYER
DRIVER CHARACTERISTICS FOR FAST SLEW RATE
Fast Bit Rate (Programming Mode)
BRFAST
kBit/s
LIN PHYSICAL LAYER
TRANSMITTER CHARACTERISTICS FOR NORMAL SLEW RATE - 20.0 KBIT/SEC
33662S DEVICE
(19)
Symmetry of Transmitter delay(18)
s
tTRAN_SYM
-7.25
—
7.25
tTRAN_SYM = MAX (tTRAN_SYM60%, tTRAN_SYM40%
tTRAN_SYM60% = | tTRAN_PDF60% - tTRAN_PDR60%
tTRAN_SYM40% = | tTRAN_PDF40% - tTRAN_PDR40%
)
|
|
Notes
15. Bus load RBUS and CBUS 1.0 nF / 1.0 k, 6.8 nF / 660 , 10 nF / 500 . Measurement thresholds: 50% of TXD signal to LIN signal
threshold defined at each parameter. See Figure 8.
16. See Figure 9.
17. See Figure 10.
18. See Figure 11
19. VSUP from 7.0 to 18 V, bus load RBUS and CBUS 1.0 nF / 1.0 k, 6.8 nF / 660 , 10 nF / 500 . Measurement thresholds: 50% of TXD
signal to LIN signal threshold defined at each parameter. See Figure 8.
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 6. Dynamic Electrical Characteristics (continued)
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
LIN PHYSICAL LAYER
RECEIVER CHARACTERISTICS ACCORDING LIN2.1
33662L AND 33662J AND 33662S DEVICES
(20)
Propagation Delay and Symmetry(21)
s
tREC_PD
Propagation Delay of Receiver, tREC_PD = MAX (tREC_PDR, tREC_PDF
Symmetry of Receiver Propagation Delay, tREC_PDF - tREC_PDR
)
)
—
—
—
6.0
2.0
tREC_SYM
-2.0
LIN PHYSICAL LAYER
RECEIVER CHARACTERISTICS WITH TIGHTEN LIMITS
(22)
33662S DEVICE
Propagation Delay and Symmetry(23)
s
tREC_PD_S
Propagation Delay of Receiver, tREC_PD = MAX (tREC_PDR, tREC_PDF
Symmetry of Receiver Propagation Delay, tREC_PDF - tREC_PDR
—
—
—
5.0
1.3
tREC_SYM_S
-1.3
LIN PHYSICAL LAYER
RECEIVER CHARACTERISTICS - LIN SLOPE 1.0 V/ns
(22)
33662S DEVICE
Propagation Delay and Symmetry(24)
s
tREC_PD_FAST
Propagation Delay of Receiver, tREC_PD _FAST= MAX (tREC_PDR_FAST
tREC_PDF_FAST
,
—
—
—
6.0
1.3
)
tREC_SYM_FAST
Symmetry of Receiver Propagation Delay, tREC_PDF_FAST - tREC_PDR_FAST
-1.3
SLEEP MODE AND WAKE-UP TIMINGS
Sleep Mode Delay Time (25)
tSD
µs
after EN High to Low to INH High to Low with 100 µA load on INH
50
—
91
WAKE-UP TIMINGS
Bus Wake-up Deglitcher (Sleep Mode) (26)
EN Wake-up Deglitcher (27)
EN High to INH Low to High
tWUF
40
—
10
70
—
48
100
15
s
s
tLWUE
Wake-up Deglitcher (28)
tWF
s
Wake state change to INH Low to High
70
TXD TIMING
TXD Permanent Dominant State Delay(29)
FIRST DOMINANT BIT VALIDATION
First dominate bit validation delay when device in Normal Mode(30)
Notes
tTXDDOM
3.75
—
5.0
50
6.25
80
ms
µs
tFIRST_DOM
20. VSUP from 7.0 to 18 V, bus load RBUS and CBUS 1.0 nF / 1.0 k, 6.8 nF / 660 , 10 nF / 500 . Measurement thresholds: 50% of TXD
signal to LIN signal threshold defined at each parameter. See Figure 8.
21. See Figure 12.
22. VSUP from 7.0 to 18 V, bus load RBUS and CBUS 1.0 nF / 1.0 k, 6.8 nF / 660 , 10 nF / 500 . Measurement thresholds: 50% of TXD
signal to LIN signal threshold defined at each parameter. See Figure 8.
23. See Figure 12
24. See Figure 13
25. See Figure 25 and 26
26. See Figure 16, 19, and Figure 20
27. See Figure 14, 17, Figure 21, Figure 25 and Figure 26
28. See Figure 15, 18, Figure 25 and Figure 26
29. The LIN is in recessive state and the receiver is still active.
30. See Figure 14, 17, 15, 18, 16, 19 and Figure 24
33662
Analog Integrated Circuit Device Data
12
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
Table 6. Dynamic Electrical Characteristics (continued)
Characteristics under conditions 7.0 V VSUP 18 V, -40C TA 125C, GND = 0 V, unless otherwise noted. Typical
values reflect the approximate parameter means at TA = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
FAST BAUD RATE TIMING
EN Low Pulse Duration to Enter in Fast Baud Rate using Toggle Function (31)
t1
s
—
—
—
45
—
EN High to Low and Low to High
TXD Low Pulse Duration to Enter in Fast Baud Rate using Toggle Function (31)
t2
t3
12.5
µs
µs
Delay Between EN Falling Edge and TXD Falling Edge to Enter in Fast Baud
Rate Using Toggle Function (31)
12.5
12.5
—
—
—
—
Delay Between TXD Rising Edge and EN Rising Edge to Enter in Fast Baud
Rate Using Toggle Function (31)
t4
t5
µs
µs
RXD Low Level duration after EN rising edge to validate the Fast Baud Rate
entrance(31)
1.875
6.25
Notes
31. See Figure 22 and 23
TIMING DIAGRAMS
V
SUP
VSUP
TXD
R0
LIN
RXD
GND
C0
Note R0 and C0: 1.0 k/1.0 nF, 660 /6.8 nF, and 500 /10 nF.
Figure 8. Test Circuit for Timing Measurements
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TXD
TBIT
TBIT
t
(MAX)
t
(MIN)
BUS_REC
BUS_DOM
VLIN_REC
REC(MAX)74.4% VSUP
TH
Thresholds of
receiving node 1
58.1% V
SUP
TH
TH
DOM(MAX)
LIN
Thresholds of
receiving node 2
42.2% V
28.4% V
SUP
TH
REC(MIN)
SUP
DOM(MIN)
t
(MIN)
BUS_DOM
t
(MAX)
BUS_REC
RXD
Output of receiving Node 1
t
REC_PDF(1)
t
REC_PDR(1)
RXD
Output of receiving Node 2
t
REC_PDF(2)
t
REC_PDR(2)
Figure 9. LIN Timing Measurements for Normal Baud Rate (33662L and 33662S)
TXD
TBIT
TBIT
t
(MAX)
t
(MIN)
BUS_REC
BUS_DOM
VLIN_REC
REC(MAX)77.8% VSUP
Thresholds of
receiving node 1
TH
61.6% V
SUP
TH
DOM(MAX)
LIN
Thresholds of
receiving node 2
38.9% V
25.1% V
SUP
SUP
TH
REC(MIN)
TH
DOM(MIN)
t
(MIN)
BUS_DOM
t
(MAX)
BUS_REC
RXD
Output of receiving Node 1
t
REC_PDF(1)
t
REC_PDR(1)
RXD
Output of receiving Node 2
t
REC_PDF(2)
t
REC_PDR(2)
Figure 10. LIN Timing Measurements for Slow Baud Rate (33662J)
33662
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TXD
VLIN_REC
LIN BUS SIGNAL
60% V
40% V
SUP
V
BUSREC
V
SUP
SUP
V
BUSDOM
t
t
t
TRAN_PDR40%
TRAN_PDF60%
TRAN_PDF40%
t
TRAN_PDR60%
Figure 11. LIN Transmitter Timing for 33662S
VLIN_REC
60% V
40% V
SUP
V
BUSREC
V
SUP
LIN BUS SIGNAL
SUP
V
BUSDOM
RXD
t
t
REC_PDF
REC_PDR
Figure 12. LIN Receiver Timing
VLIN_REC
1V/ns
60% V
40% V
SUP
V
BUSREC
V
SUP
LIN BUS SIGNAL
SUP
V
BUSDOM
RXD
t
t
REC_PDF_FAST
REC_PDR_FAST
Figure 13. LIN Receiver Timing LIN slope 1V/ns
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
ELECTRICAL CHARACTERISTICS
FUNCTIONAL DIAGRAMS
FUNCTIONAL DIAGRAMS
EN
INH
VBUSWU
LIN
tWUF
Normal Mode
tLWUE
INH
EN
tFIRST_DOM
TXD
tFIRST_DOM
TXD
LIN
Awake Mode
(High Z)
RXD
RXD
(High Z)
WAKE
WAKE
Figure 16. LIN Bus Wake-up with TXD High
Figure 14. EN Pin Wake-up with TXD High
WAKE
EN
INH
WAKE after deglitcher
tLWUE
tWF
Normal Mode
INH
tFIRST_DOM
TXD
LIN
tFIRST_DOM
EN
TXD
RXD
(High Z)
LIN
RXD
(High Z)
Awake Mode
WAKE
Figure 15. WAKE Pin Wake-up with TXD High
Figure 17. EN Pin Wake-up with TXD Low
33662
Analog Integrated Circuit Device Data
16
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
FUNCTIONAL DIAGRAMS
WAKE
VBUSWU
tWUF
WAKE after deglitcher
LIN
tWF
INH
EN
tFIRST_DOM
INH
tFIRST_DOM
EN
TXD
TXD
Awake Mode
(High Z)
RXD
LIN
RXD
(High Z)
Awake Mode
WAKE
Figure 18. WAKE Pin Wake-up with TXD Low
Figure 19. LIN Bus Wake-up with TXD Low
INH
EN
TXD
LIN
No wake-up
t>tWUF
RXD
(High Z)
WAKE
Preparation to Sleep Mode
No communication available
Sleep Mode
Awake
mode
No communication available
Device in
Communication Mode
Normal Mode
LIN wake-up event not take into
account
Wake & LIN wake-up events
allowed
t
SD
Figure 20. LIN Bus Wake-up with LIN bus in Dominant During the Preparation to Sleep Mode
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
ELECTRICAL CHARACTERISTICS
FUNCTIONAL DIAGRAMS
EN pin
t
LWUE
EN internal signal
t
LWUE
EN pin
t < t
LWU
E
EN internal signal
5V
5V
EN pin
t < t
LWU
E
EN internal signal
Figure 21. EN Pin Deglitcher
t1 (45 s)
EN
Fast Baud Rate entrance
t2 (12.5 s)
TXD
t
(12.5
s)
t4 (12.5 s)
3
LIN
Fast Baud Rate validation
RXD
t5
Figure 22. Fast Baud Rate Selection (Toggle Function)
t1 (45 s)
EN
Exit Fast Baud Rate
t2 (12.5 s)
TXD
t
(12.5
s)
t4 (12.5 s)
3
LIN
RXD stays High for Normal or Slow mode validation
RXD
Figure 23. Fast Baud Rate Mode Exit (back to Normal or Slow slew rate)
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
ELECTRICAL CHARACTERISTICS
FUNCTIONAL DIAGRAMS
VSUP
VUVL
POR (3.5-5.3 V)
POR (3.5-5.3 V)
VSUP
EN
160 µs
EN
(High or Low)
Normal Mode
INH
INH
tFIRST_DOM
(High or Low)
TXD
(High or Low)
TXD
LIN
LIN
Awake Mode
RXD
(High Z)
RXD
(High Z)
*: this parameter is guaranteed by design
Figure 24. Power Up and Down Sequences
INH
t
LWUE
EN
TXD
LIN
(High Z)
RXD
t
WF
WAKE
WAKE after deglitcher
Preparation to Sleep Mode
Sleep
Mode
Device in
Communication Mode
No communication allowed
LIN wake-up event not take into
account
t
SD
Figure 25. Sleep Mode Sequence
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
ELECTRICAL CHARACTERISTICS
FUNCTIONAL DIAGRAMS
INH
INH
EN
t
t
LWUE
LWUE
EN
TXD
TXD
No communication
No communication
allowed
LIN
LIN
allowed
(High Z)
(High Z)
RXD
RXD
WAKE
(case 1)
WAKE
(case 2)
WAKE after deglitcher
(case 1)
WAKE after deglitcher
(case 2)
t = tWF
t tWF
Awake Mode
Preparation to
Sleep Mode
Awake Mode
Device in
Communication Mode
Device in
Communication Mode
t < t
SD
Sleep Mode (t < tSD
)
Preparation to
The device does not enter in Sleep Mode
The device does not enter in Sleep Mode
INH
EN
t
LWUE
TXD
No communication
allowed
LIN
(High Z)
RXD
WAKE
(case 3)
t tWF
WAKE after deglitcher
(case 3)
t tSD
Device in
Communication Mode
Sleep
Mode
Preparation to
Sleep Mode
Awake Mode
Figure 26. Examples of Sleep Mode Sequences
33662
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33662L, 33662J, and 33662S are a physical layer
component dedicated to automotive LIN sub-bus
applications.
LIN bus short-to-ground, or a LIN bus leakage during low
power mode.
Digital inputs are 5.0 and 3.3 V compatible without any
external required components.
The 33662L and 33662S features include a 20 kbps baud
rate and the 33662J a 10 kbps baud rate. They integrate fast
baud rate for test and programming modes, excellent ESD
robustness, immunity against disturbance, and radiated
emission performance. They have safe behavior in case of a
The INH output can be used to control an external voltage
regulator, or to drive a LIN bus pull-up resistor.
FUNCTIONAL PIN DESCRIPTION
POWER SUPPLY PIN (VSUP)
LIN overtemperature
OR
The VSUP supply pin is the power supply pin for the
33662L, or 33662J, or 33662S. In an application, the pin is
connected to a battery through a serial diode, for reverse
battery protection. The DC operating voltage is from 7.0 to
18 V. This pin can sustain a standard automotive load dump
condition up to 40 V. To avoid a false bus message, an
undervoltage on VSUP disables the transmission path (from
TXD to LIN) when VSUP falls below 6.7 V. Supply current in
Sleep mode is typically 6.0 A.
INH overtemperature
INH switched off &
LIN transmitter and receiver disabled
VSUP
LIN Wake up
INH_ON
INH
LIN Driver
Slope Control
EN_sleep
VSUP Undervoltage
TXD Dominant
30 k
725 k
LIN
X 1
EN
35µA
GROUND PIN (GND)
TXD
RXD
In case of a ground disconnection at the module level, the
33662L, 33662J, and 33662S do not have significant current
consumption on the LIN bus pin when in the recessive state.
Receiver
Figure 27. LIN Interface
LIN BUS PIN (LIN)
Transmitter Characteristics
The LIN driver is a low side MOSFET with internal
overcurrent thermal shutdown. An internal pull-up resistor
with a serial diode structure is integrated so no external pull-
up components are required for the application in a slave
node. An additional pull-up resistor of 1.0 k must be added
when the device is used in the master node.
The LIN pin represents the single-wire bus transmitter and
receiver. It is suited for automotive bus systems, and is
compliant to the LIN bus specification 1.3, 2.0, 2.1, and
SAEJ2602-2.
The LIN interface is only active during Normal mode (See
Figure 27).
The LIN pin exhibits no reverse current from the LIN bus
line to VSUP, even in the event of a GND shift or VSUP
disconnection. The 33662 is tested according to the
application conditions (i.e. in normal mode and recessive
state during communication).
The transmitter has a 20 kbps baud rate (Normal baud
rate) for the 33662L and 33662S devices, or 10 kbps baud
rate (Slow baud rate) for the 33662J device. As soon as the
device enters in Normal mode, the LIN transmitter will be able
to send the first dominant bit only after the tFIRST_DOM delay.
t
FIRST_DOM delay has no impact on the receiver. The receiver
will be enabled as soon as the device enters in Normal mode.
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
Receiver Characteristics
EN
The receiver thresholds are ratiometric with the device
supply pin.
X 1
200 k
If the VSUP voltage goes below the VSUP undervoltage
LIN_RXD
VSUP
threshold (V , VUVH), the bus enters into a recessive state
RXD
UVL
even if communication is sent to TXD.
EN_RXD
In case of LIN thermal shutdown, the transceiver and
receiver are in recessive and INH turned off. When the
30 k
Receiver
LIN
temperature is below the T
, INH and LIN will be
LINSD
automatically enabled.
Slope
Control
The Fast Baud Rate selection is reported by the RXD pin.
Fast Baud Rate is activated by the toggle function (See
Figure 22). At the end of the toggle function, just after EN
rising edge, RXD pin is kept low for t5 to flag the Fast Baud
Figure 28. RXD Interface
The RXD output pin is the receiver output of the LIN
Rate entry (See Figure 22).
interface. The low level is fixed. The high level is dependent
on EN voltage. If EN is set at 3.3 V, RXD VOH is 3.3 V. If EN
is set at 5.0 V, RXD VOH is 5.0 V.
To exit the Fast Baud Rate and return in Normal or Slow
baud rate, a toggle function is needed. At the end of the
toggle function, the RXD pin stays high to signal Fast Baud
Rate exit (See Figure 23). The device enters into Fast Baud
Rate at room and hot temperature.
In Sleep mode, RXD is high-impedance. When a wake-up
event is recognized from the WAKE pin or from the LIN bus
pin, RXD is pulled LOW to report the wake-up event. An
external pull-up resistor may be needed.
DATA INPUT PIN (TXD)
The TXD input pin is the MCU interface to control the state
of the LIN output. When TXD is LOW (dominant), LIN output
is LOW; when TXD is HIGH (recessive), the LIN output
transistor is turned OFF. TXD pin thresholds are 3.3 V and
5.0 V compatible.
ENABLE INPUT PIN (EN)
EN input pin controls the operation mode of the interface.
If EN = 1, the interface is in Normal mode, TXD to LIN after
tFIRST_DOM delay and LIN to RXD paths are both active. EN
pin thresholds are 3.3 V and 5.0 V compatible. RXD VOH
level follows EN pin high level. The device enters the Sleep
mode by setting EN LOW for a delay higher than tSD (70 µs
typ. value) and if the WAKE pin state doesn’t change during
this delay (see Figure 25).
This pin has an internal pull-up current source to force the
recessive state if the input pin is left floating.
If the pin stays low (dominant sate) more than 5.0 ms
(typical value), the LIN transmitter goes automatically into
recessive state.
A combination of the logic levels on the EN and TXD pins
allows the device to enter into the Fast Baud Rate mode of
operation (see Figure 22).
DATA OUTPUT PIN (RXD)
RXD output pin is the MCU interface, which reports the
state of the LIN bus voltage.
INHIBIT OUTPUT PIN (INH)
In Normal or Slow baud rate, LIN HIGH (recessive) is
reported by a high voltage on RXD; LIN LOW (dominant) is
reported by a low voltage on RXD.
The INH output pin is connected to an internal high side
power MOSFET. The pin has two possible main functions. It
can be used to control an external switchable voltage
regulator having an inhibit input. It can also be used to drive
the LIN bus external resistor in the master node application,
thanks to its high drive capability. This is illustrated in
Figure 30 and 31.
The RXD output structure is a tristate output buffer (See
Figure 28).
In Sleep mode, INH is turned OFF. If a voltage regulator
inhibit input is connected to INH, the regulator will be
disabled. If the master node pull-up resistor is connected to
INH, the pull-up resistor will be unpowered and left floating.
In case of a INH thermal shutdown, the high side is turned
off and the LIN transmitter and receiver are in recessive state.
An external 10 to 100 pF capacitor on INH pin is advised
in order to improve EMC performances.
33662
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
lower than tWF, the device will not enter the Sleep mode, but
will go into Awake mode (See Figure 26).
WAKE INPUT PIN (WAKE)
The WAKE pin is a high voltage input used to wake-up the
device from the Sleep mode. WAKE is usually connected to
an external switch in the application.
An internal filter is implemented to avoid a false wake-up
event due to parasitic pulses (See Figure 15 and 18). WAKE
pin input structure exhibits a high-impedance, with extremely
low input current when voltage at this pin is below 27 V. Two
serial resistors should be inserted in order to limit the input
current mainly during transient pulses and ESD. The total
recommended resistor value is 33 k. An external 10 to
100 nF capacitor is advised for better EMC and ESD
performances.
The WAKE pin has a special design structure and allows
wake-up from both HIGH to LOW or LOW to HIGH
transitions. When entering into Sleep mode, the device
monitors the state of the WAKE pin and stores it as a
reference state. The opposite state of this reference state will
be the wake-up event used by the device to enter again into
Normal mode.
Important The WAKE pin should not be left open. If the
wake-up function is not used, WAKE should be connected to
ground to avoid a false wake-up.
If the Wake pin state changes during the Sleep mode
Delay Time (tSD) or before EN goes low with a deglitcher
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
As described below and depicted in Figure 29 and
Table 7, the 33662L, 33662J, and 33662S have two
operational modes, Normal and Sleep. In addition, there are
two transitional modes: Awake mode and Preparation to
Sleep mode. The Awake mode allows the device to go into
Normal mode. The Preparation to Sleep mode allows the
device to go into Sleep mode.
If the WAKE pin state changes during tSD and if tWF is
reached after end of tSD then the device goes into Sleep
mode after the end of tSD timing.
If the WAKE pin state changes during tSD and tWF delay
has been reached before the end of tSD then the device goes
into Awake mode.
If the WAKE pin state changes before tSD and the delay
tWF ends during tSD then the device goes into Awake mode.
NORMAL OR SLOW BAUD RATE
If EN goes high for a delay higher than tLWUE, the 33662
returns to Normal mode.
In the Normal mode, the LIN bus can transmit and receive
information.
The 33662L and 33662S (20 kbps) have a slew rate and
timing compatible with Normal Baud Rate and LIN protocol
specification 1.3, 2.0, and 2.1.
SLEEP MODE
To enter into Sleep mode, EN must be low for a delay
longer than tSD and the Wake pin must stay in the same state
(High or Low) during this delay.
The 33662J (10 kbps) has a slew rate and timing
compatible with Low Baud Rate.
The device conditions to not enter in Sleep mode but enter
in Awake mode are detailed in the Preparation into Sleep
mode chapter. See Figure 26.
From Normal mode, the three devices can enter into Fast
Baud Rate (Toggle function).
In Sleep mode, the transmission path is disabled and the
device is in Low Power mode. Supply current from VSUP is
very low (6.0 µA typical value). Wake-up can occur from LIN
bus activity, from the EN pin and from the WAKE input pin. If
during the preparation to Sleep mode delay (tSD), the LIN bus
goes low due to LIN network communication, the device still
enters into the Sleep mode. The device can be awakened by
a recessive to dominant start, followed by a dominant to
FAST BAUD RATE
In Fast Baud Rate, the slew rate is around 10 times faster
than the Normal Baud Rate. This allows very fast data
transmission (>100 kbps) -- for instance, for electronic
control unit (ECU) tests and microcontroller program
download. The bus pull-up resistor might be adjusted to
ensure a correct RC time constant in line with the high baud
rate used.
recessive state after t > tWUF
After a Wake-up event, the device enters into Awake
mode.
.
Fast Baud Rate is entered via a special sequence (called
toggle function) as follows:
1- EN pin set LOW while TXD is HIGH
2- TXD stays HIGH for 12.5 µs min
3- TXD set LOW for 12.5 µs min
In the Sleep mode, the internal 725 kOhm pull-up resistor
is connected and the 30 kOhm is disconnected.
DEVICE POWER-UP (Awake Transitional Mode)
4- TXD pulled HIGH for 12.5 µs min
5- EN pin set LOW to HIGH while TXD still HIGH
At power-up (VSUP rises from zero), when VSUP is above
the Power On Reset voltage, the device automatically
switches after a 160 µs delay time to the Awake transitional
mode. It switches the INH pin to a HIGH state and RXD to a
LOW state. See Figure 24.
The device enters into the Fast Baud Rate if the delay
between Step 1 to Step 5 is 45 µs maximum. The toggle
function is described in Figures 22. Once in Fast Baud Rate,
the same toggle function just described previously is used to
bring the device back into Normal Baud Rate.
DEVICE WAKE-UP EVENTS
Fast Baud Rate selection is reported to the MCU by RXD
pin. Once the device enters in this Fast Baud Rate, the RXD
pin goes at low level for t5. When the device returns in Normal
Baud Rate with the same toggle function, the RXD pin stays
high. Both sequences are illustrated in Figures 22 and 23.
The 33662L, 33662J, and 33662S can be awakened from
Sleep mode by three wake-up events:
• Remote wake-up via LIN bus activity
• Via the EN pin
• Toggling the WAKE pin
PREPARATION TO SLEEP MODE
Remote Wake from LIN Bus (Awake Transitional Mode)
To enter the Preparation to Sleep mode, EN must be low
The device is awakened by a LIN dominant pulse longer
than tWUF. Dominant pulse means: a recessive to dominant
transition, wait for t > tWUF, then a dominant to recessive
for a delay higher than tLWUE
.
If the WAKE pin state doesn’t change during tSD and tLWUE
then the 33662 goes into Sleep mode.
33662
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
transition. This is illustrated in Figure 16 and 19. Once the
wake-up is detected (during the dominant to recessive
transition), the device enters into Awake mode, with INH
HIGH and RXD pulled LOW.
17. Once in Normal mode, the device has to wait tFIRST_DOM
delay before transmitting the first dominant bit.
Wake-up from WAKE Pin (Awake Transitional Mode)
Once in the Awake mode, the EN pin has to be set to 3.3 V
or 5.0 V (depending on the system) to enter into Normal
mode. Once in Normal mode, the device has to wait tfirst_dom
delay before transmitting the first dominant bit.
Just before entering the Sleep mode, the WAKE pin state
is stored. A change in the level longer than the deglitcher time
(70 µs maximum) will generate a wake-up, and the device
enters into the Awake Transitional mode, with INH HIGH and
RXD pulled LOW. See Figure 15 and 18. The device goes
into Normal mode when EN is switched from LOW to HIGH
and stays HIGH for a delay higher than tLWUE. Once in
Normal mode, the device has to wait tFIRST_DOM delay before
transmitting the first dominant bit.
Wake-up from EN pin
The device can be waked-up by a LOW to HIGH transition
of the EN pin. When EN is switched from LOW to HIGH and
stays HIGH for a delay higher than tLWUE, the device is
awakened and enters into Normal mode. See Figure 14 and
FAIL-SAFE FEATURES
The table below describes the 33662 protections.
BLOCK
FAULT
FUNCTIONAL
MODE
CONDITION
RESPONSE
RECOVERY
CONDITION
RECOVERY
FUNCTIONALITY MODE
Device goes in Awake
mode whatever the
previous device mode
Power
Supply
Power on Reset
(POR)
V
< 3.5 V (min)
SUP
then power up
All modes
No internal supplies
Condition gone
Condition gone
Normal,
Awake &
Preparation to
Sleep modes
INH high side turned
off. LIN transmitter
and receiver in
INH Thermal
Shutdown
Temperature >
160 °C (typ)
Device returns in same
functional mode
INH
recessive state
LIN transmitter in
recessive state
Device returns in same
functional mode
V
undervoltage
V
< V
UVL
Condition gone
Condition gone
SUP
SUP
Normal
TXDPinPermanent
Dominant
TXD pin low for more
than 5.0 ms (typ)
LIN transmitter in
recessive state
Device returns in same
functional mode
LIN
LIN transmitter and
receiver in recessive
state
Normal mode
LIN Thermal
Shutdown
Temperature >
160 °C (typ)
Device returns in same
functional mode
Condition gone
INH high side turned
off
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Power Up
EN HIGH to LOW for t > t
LWUE
Fast Baud
Rate (10x)
V
> V
POR
SUP
Toggle
Function
(33)
EN LOW to HIGH for t > t
LWUE
Awake
(30)
Internal WAKE
state
changes during t
SD
Normal Baud Rate for
33662L and 33662S
or
EN HIGH to LOW
for t > t
LIN bus dominant pulse
(31)
WUF
LWUE
for t > t
or
WAKE pin state
Preparation
to Sleep
Slow Baud Rate
for 33662J
Toggle
Function
(33)
EN LOW to HIGH
(32)
changes for t > t
for t > t
WF
LWUE
(30)
Internal WAKE
state
doesn’t change during t
SD
Sleep
EN LOW to HIGH for t > t
LWUE
Notes
32. Internal WAKE is the WAKE signal filtered by t
(WAKE deglitcher)
WF
33. See Figure 15 and Figure 18
34. See figures Figure 14 and Figure 17
35. The Toggle Function is guaranteed at ambient and hot temperature
Figure 29. Operational and Transitional Modes State Diagram
Table 7. Explanation of Operational and Transitional Modes State Diagram
Operational/
Transitional
LIN
INH
EN
TXD
RXD
(36)
Recessive state, driver off with
725 k pull-up
High-impedance.
Sleep
OFF
(low)
LOW
X
HIGH if external pull-up to V
DD
Recessive state, driver off.
725 k pull-up active
LOW.
Awake
ON
LOW
X
X
If external pull-up, HIGH-to-LOW
transition reports wake-up
(high)
Recessive state, driver off with
725 k pull-up
High-impedance. HIGH if
external pull-up to V
Preparation to
Sleep mode
ON
LOW
HIGH
DD
(high)
Driver active. 30 k pull-up active
Normal Baud Rate for 33662L
and 33662S
LOW to drive LIN bus in dominant Report LIN bus state:
Normal mode
ON
• Low LIN bus dominant
• High LIN bus recessive
HIGH to drive LIN bus in recessive
(high)
Slow Baud Rate for 33662J
Fast Baud Rate (> 100 kbps) for
33662L, 33662S, & 33662J
X = Don’t care.
Notes
36. Only applies to 33662B. The 33662 will have a leakage current of typically 95 A if a pull-up resistor is implemented.
The LIN 2.1 physical layer and is backward compatible
with the LIN 1.3 physical layer, but not the other way around.
The LIN 2.1 physical layer sets harder requirements, i.e. a
node using the LIN 2.1 physical layer can operate in a LIN 1.3
cluster.
COMPATIBILITY WITH LIN1.3
Following the Consortium LIN specification Package,
Revision 2.1, November 24, 2006, Chapter 1.1.7.1
Compatibility with LIN1.3, page 15.
33662
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
TYPICAL APPLICATIONS
TYPICAL APPLICATIONS
The 33662 can be configured for several applications.
Figure 30 and 31 show master and slave node applications.
An additional pull-up resistor of 1.0 k in series with a diode
between the INH and LIN pins must be added when the
device is used in the master node.
C1
D1
C2
100nF
VBAT
22µF
VSUP
R2
R3
R4
18k 18k
2.2k
X 1
INH_ON
INH
EN
I/O
EN_sleep
D2
Control
Unit
VDD
VDD
Regulator
200 k
MCU
R1
*
*
12V
1.0 k
RXD
30 k
725 k
VDD
RXD
5V or
3.3V
RXD_Int
LIN_en
LIN
Receiver
LIN Bus
EN_RXD
TXD
35µA
Slope
Control
TXD_Int
TXD
WAKE
C3
100nF
GND
*: Optional. 2.2k if implemented
Figure 30. Master Node Typical Application
C1
D1
C2
100nF
VBAT
22µF
VSUP
R2
R3
R4
18k 18k
2.2k
X 1
INH_ON
INH
LIN
EN
I/O
EN_sleep
Control
Unit
VDD
VDD
*
Regulator
200 k
MCU
12V
*
RXD
30 k
725 k
VDD
RXD
5V or
3.3V
RXD_Int
LIN_en
Receiver
LIN Bus
EN_RXD
TXD
35µA
Slope
Control
TXD_Int
TXD
WAKE
C3
100nF
GND
*: Optional. 2.2k if implemented
Figure 31. Slave Node Typical Application
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
PACKAGING
PACKAGE DIMENSIONS
PACKAGING
PACKAGE DIMENSIONS
Important For the most current revision of the package, visit www.Freescale.com and do a keyword search on the 98A
drawing number below.
EF SUFFIX
8-PIN
98ASB42564B
REVISION V
33662
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
PACKAGING
PACKAGE DIMENSIONS
EF SUFFIX
8-PIN
98ASB42564B
REVISION V
33662
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
REVISION HISTORY
PACKAGE DIMENSIONS
REVISION HISTORY
REVISION
DATE
8/2011
9/2011
1/2014
DESCRIPTION OF CHANGES
3.0
4.0
5.0
Initial release
Changed the PC part numbers in the Ordering Information Table to MC
•
•
•
Added MC33662BLEF, MC33662BJEF, and MC33662BSEF to the ordering information.
Updated Device Variations table
Changed LIN dominant level with 500 680 and 1.0 k load on the LIN bus from 0.3 to
0.25
•
•
Changed LIN Wake-up Threshold from Sleep Mode from 5.0 to 5.3
MC33662LEF/MC33662SEF/MC33662JEF INH pin HBM level 8.0 KV removed to reflect
performance
•
Corrected MC33662BLEF, MC33662BJEF, and MC33662BSEF to PC in the ordering
information.
Minor corrections to format.
6.0
7.0
1/2014
1/2014
•
•
Changed MC33662BLEF, MC33662BJEF, and MC33662BSEF to MC in the ordering
information. Now qualified.
33662
Analog Integrated Circuit Device Data
30
Freescale Semiconductor
Information in this document is provided solely to enable system and software implementers to use Freescale products.
There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based
on the information in this document.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no
warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance
may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by
customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others.
Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:
freescale.com/SalesTermsandConditions.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off.
SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their
respective owners.
© 2014 Freescale Semiconductor, Inc.
Document Number: MC33662
Rev. 7.0
1/2014
MC33662JEF 替代型号
型号 | 制造商 | 描述 | 替代类型 | 文档 |
MC33662BJEF | NXP | Transceiver, Physical Layer, LIN 2.1 / SAEJ2602-2, 10kbps, SOIC 8, Rail | 完全替代 |
MC33662JEF 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
MC33662LEF | NXP | Transceiver, Physical Layer, LIN 2.1 / SAEJ2602-2, 20kbps,TX/RX symmetry, SOIC 8, Rail | 获取价格 | |
MC33662SEF | NXP | Transceiver, Physical Layer, LIN 2.1 / SAEJ2602-2, 20kbps, SOIC 8, Rail | 获取价格 | |
MC33663 | FREESCALE | LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer | 获取价格 | |
MC33663AJEF | FREESCALE | LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer | 获取价格 | |
MC33663ALEF | FREESCALE | LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer | 获取价格 | |
MC33663ASEF | FREESCALE | LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer | 获取价格 | |
MC33664ATL1EG | NXP | Interface Circuit | 获取价格 | |
MC33665ATF4AE | NXP | High speed transceiver with CAN FD Gateway | 获取价格 | |
MC33665ATS4AE | NXP | High speed transceiver with SPI Interface | 获取价格 | |
MC3367 | MOTOROLA | LOW VOLTAGE FM NARROWBAND RECEIVER | 获取价格 |
MC33662JEF 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6