FXP1800-48G [POWER-ONE]
1500 to 5400-Watt Front-End Power Solutions; 1500〜 5400瓦前端电源解决方案
| 型号： | FXP1800-48G |
| 厂家： | 
POWER-ONE |
| 描述： | 1500 to 5400-Watt Front-End Power Solutions |
| 文件： | 总15页 (文件大小：709K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
1500 to 5400-Watt
Front-End Power Solutions
Features
•
•
•
•
•
•
•
•
•
RoHS compliant for all six substances
High density front-ends 15.2 to 18.3 W/in3
Wide input voltage range 85 to 264 VAC
12 V standby voltage, 1A per front-end
Highly efficient topology reduces operating costs
I2C interface status and control
(1500 or 1800 Watts)
Front-Ends are available using either a front-mounted
AC receptacle (FNP models) or a rear-mounted AC
connector (FXP models).
I2C Management Software: All FNP/FXP front-ends can be
controlled via Power-One's GUI-driven I2C Management
software and an I2C-to-USB interface (P/N HZZ02002G). An
I2C Programming Manual describes the complete range of
parameters that can be programmed to the FNP and
FXP1500/1800 front-ends. This manual is available by
searching on "FNP1500" at www.power-one.com.
I2C voltage and current limit setting
Analog output voltage setting
Overtemperature, output overvoltage, and output
overcurrent protection
•
•
ORing circuits for true redundant operation:
Vo1: ORing FETs; Vo2: ORing Diodes
Status LEDs: AC OK, DC OK, and
Fan Fail/Overtemperature Fail
Applications
•
•
•
•
Telecommunications
Data communications
Servers
Distributed power
FNR-3
Power Shelf
FNR-3 and FXR-3 shelves provide up to 5400 watts in a 19" rack.
(See the Rack section for power shelf details.)
Description
The FNP/FXP-1500/1800 are power-factor-corrected (PFC) front-ends which (depending on model type) provide a 12 VDC or 48
VDC (1500 or 1800 watt) output, and can be used in hot-swap redundant systems. Their very small dimensions allow
configuration of up to three units in a 1U rack. The FNP front-ends have a front-mounted AC receptacle and the FXP front-ends
have a rear-mounted AC connector. The highly-efficient thermal design with internal-fan cooling permits their use over wide
temperature ranges and provides very-high reliability.
Status information is provided with front panel LEDs, logic signals, and via an I2C management interface. In addition, the I2C bus
can enable the power supply, set high fan speed, adjust the output voltage, and set the output current limit. The FNP and
FXP-1500/1800's meet international safety standards and display the CE-Mark for the European Low Voltage Directive (LVD).
Power-shelf solutions provide rectification, system management, and power distribution, while maintaining high reliability and
offering flexibility for future expansion. The power shelves can be configured with up to three hot-swappable 1500 or 1800-watt
AC-DC front-ends.
DEC 12, 2006 revised to FEB 22, 2007
Page 1 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Model Selection
Output 1
Output 2
Input voltage
Rated power
W
Compatible
Shelf 2
Model
VAC
Vo1 nom
VDC
Io1 max
ADC
Vo2 nom
VDC
Io2 max
ADC
auto selected 1
FNP1500-12G
&
FXP1500-12G
FNP1500-48G
&
108 – 264
85 – 105
12
12
129 @ 11.64V
101.8 @ 11.78A
12
12
1
1
1512
1212
FNR-3-12G &
FXR-3-12G
105 – 264
85 – 105
48
48
32.2
25.4
12
12
1
1
1512
1212
FNR-3-48G &
FXR-3-48G
FXP1500-48G
FNP1800-48G
&
FXP1800-48G
180 – 264
105 – 180
85 – 105
48
48
48
39.2
32.2
25.4
12
12
12
1
1
1
1812
1512
1212
FNR-3-48G &
FXR-3-48G
1
The available output power is automatically adjusted depending on the input voltage.
2
1U standard racks are available from Power-One. See the Rack (Power Shelf) section of this data sheet for configurations and details.
Absolute Maximum Ratings
Stress in excess of the absolute maximum ratings may cause performance degradation, adversely effect long-term reliability, or
cause permanent damage to the converter.
Parameter
Conditions/Description
Min
Max
Unit
Input voltage
Continuous
Transient, 60 ms max.
264
300
VAC
VAC
Operating ambient temperature
Vi min-Vi max, Io nom, cooling by internal fan
@ 100 % load
@ 50 % load
0
0
50
70
°C
°C
Storage temperature
Non-Operating
-40
85
°C
Environmental, Mechanical, & Reliability Specifications
Parameter
Conditions/Description
Min
Nom
Max
Unit
Altitude
Operating
Non-Operating
10 k
40 k
ASL Ft.
ASL Ft.
Relative humidity, non-condensing
Operating
Storage
10
5
90
95
% RH
% RH
%/K
Temperature coefficient
Shock
0 °C to 70 °C (after 15 min warm-up)
IEC/EN 60068-2-27, 11 ms
0.02
40
gpk
Sinusoidal vibration
IEC/EN 60068-2-6
2-8 Hz
7.5
2
4
mil
gpk
gpk
8-200 Hz
200-500 Hz
Random vibration
MTBF
10-2000 Hz
Calculated per Bellcore (SR-332, Issue 1):
GB 25 °C
6.15
grms
230
TBD
250
kh
kh
kh
GB 25 °C (FNP1500-12G)
Demonstrated
DEC 12, 2006 revised to FEB 22, 2007
Page 2 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Safety Specifications
Maximum electric strength testing is performed in the factory according to EN 550116, IEC/EN 60950, and UL 60950.
Input-to-output electric strength tests should not be repeated in the field. Power-One will not honor any warranty claims resulting
from electric strength field tests.
Parameter
Agency approvals
Conditions/description
Min
Nom
Max
Unit
UL60950, (UL) CSA 60950 (cUL),
EN 60950(TÜV), CE Mark for LVD
Insulation safety rating
Input to case
Input to output
Output to case
Basic
Reinforced
Functional
Electric strength test voltage
Input to case
Input to output
Output to case
2.12
4.2 1
0.5
kVDC
kVDC
kVDC
kVDC
Output 1 to output 2
0.1
1 Subassemblies are pre-tested with 4.2 kVDC in accordance with EN50116 and IEC/EN60950.
EMC Specifications
Parameter
Description
Criterion
Electrostatic discharge
Electromagnetic field
Electrical fast transients/burst
Surge
Voltage dips and interruptions
RF conducted immunity
IEC/EN 61000-4-2, level 4
IEC/EN 61000-4-3, level 3
IEC/EN 61000-4-4, level 3
IEC/EN 61000-4-5, level 3
IEC/EN 61000-4-11
Performance criterion B
Performance criterion A
Performance criterion B
Performance criterion B
Performance criterion B or better
IEC/EN 61000-4-6
10 VAC, AM 80 %, 1 kHz
Performance criterion A
Emissions conducted
Emissions radiated
Harmonics
Voltage fluctuation and flicker
Voltage sag
CISPR 22/EN 55022/EN 61204
CISPR 22/EN 55022/EN 61204
IEC/EN 61000-3-2
IEC/EN 61000-3-3
SEMI F47-0200 (High Line 230V)
Class B
Class A
Class B
Pass
Pass
Input Specifications
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Input voltage
Conditions/description
Min
85
Nom
Max
264
63
Unit
VAC
Hz
230
Input frequency
47
50/60
Turn-on input voltage
Turn-off input voltage
Inrush current limitation
Ramping up
79
-
-
85
VAC
VAC
Ramping down
70
78
115/230 VAC acc. ETS 300 132-1
< 100 ms
50
20
Apk
ms
Hold-up time
Power factor
After last AC line peak ,Vi = 230 VAC, Po nom
Vi nom, Io nom
20
0.95
89 1
W/VA
%
Efficiency
Vi = 230 VAC, Io nom, TC = 25 °C
90
Max input current
Input connector
1 87% for FNP1500-12
Arms
16A – 20 A / 250 VAC; according to IEC320 C19
Input Connector Description (FXP1500/1800)
Protection Earth
Phase
P1
P2
P3
PE
L
Neutral
N
DEC 12, 2006 revised to FEB 22, 2007
Page 3 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Output Specifications, 12Vout Models
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Conditions/Description
Min
Nom
Max
Units
Nominal output voltage
Io = 64.5 A
12
VDC
Output voltage set point accuracy
Output voltage trimming
Vi = 230 VAC, Io1 = 65.5 A, TC = 25 °C
11.93
-0.42
12
12.05
+0.42
VDC
% Vo1 nom
(Factory setting)
Adjustable via I2C (Vo1 set
)
7
6.2
12
13
Vo1 set
VDC
VDC
Adjustable via Margin pin (R input)
Nominal
current
output 1
FNP1500-12G
FNP1500-12G
Io1 nom @ Vi =108 VAC – 264 VAC, Po 1.5 kW
Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW
129.0
101.8
129.0
ADC
ADC
Current
limit
output 1
Io1 max @ Vi = 108 VAC – 264 VAC droop hiccup
Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup
147.4
ADC
ADC
120..2
Nominal current output 2
Current limit output 2
Io2 nom @ Vi = 85 VAC – 265 VAC, Po 12 W
Io2 max @ Vi = 85 VAC – 265 VAC
Vi min - Vi max, 50 % Io nom, Ta = 25 °C
1.0
1.5
1.0
0.5
ADC
ADC
Static line regulation output 1
-0.5
% Vo nom
Static load
regulation
output 1
FNP1500-12G
Vi = 230 V, 5 - 100 % Io nom
Full load to no load [0..129 A] at Vo set = 12V
dVo1 over the setting range [7 to 13V]
- 5.58
12
mV/A
VDC
VDC
11.64
-0.36
12.36
+0.36
(droop
characteristic)
Static load regulation
output 2 (droop characteristic)
Full load to no load @ Vi = 85 VAC – 265 VAC
0.4
VDC
Load change 50%<─>100% Io nom, dIo/dt =1A/μs
Voltage deviation (droop + over- or undershoot)
Dynamic
load
FNP1500-12G
-2
2
% Vo nom
μs
regulation
FNP1500-12G
Max. recovery time to within 1% of Vo1 nom
400
Difference in current between two units for Vo1 above
Current
Share
10 % load.
FNP1500-12G
12.9
100
ADC
Time required for output within regulation after initial
Start-up time
application of AC-input (Vi nom, Io nom
after removal of inhibit (Vi nom, Io nom
)
1.5
s
)
ms
V
i nom, Io nom, 20 MHz bandwidth
Output voltage ripple and noise
(Filter 10nF/10µF)
Vo1
Vo2
120
120
mVpp
mVpp
Remote sense
500
mV
Total compensation for cable losses
DEC 12, 2006 revised to FEB 22, 2007
Page 4 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Output Specifications, 48Vout Models
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Conditions/Description
Io = 16.1 A
Min
Nom
48
Max
Units
VDC
Nominal output voltage Vo1
Nominal output voltage Vo2
Output voltage set point accuracy
Io = 0.5 A
12
VDC
Vi = 230 VAC, Io1 =16.1 A, TC = 25 °C
-0.5
-8
+0.5
+8
% Vo1 nom
(47.8 - 48.2 VDC)
Output voltage trimming
(via I2C or with external resistor)
Adjustable (44.16 to 51.84 VDC)
% Vo1 nom
FNP/FXP1500-48G
Io1 nom @ Vi =105 VAC – 264 VAC, Po 1.5 kW
Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW
32.2
25.4
ADC
ADC
Nominal
current
FNP/FXP1800-48G
output 1
Io1 nom @ Vi =180 VAC – 264 VAC, Po 1.8 kW
Io1 nom @ Vi =105 VAC – 180 VAC, Po 1.5 kW
Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW
39.2
32.2
25.4
39.2
ADC
ADC
ADC
FNP/FXP1500-48G
Current
Io1 max @ Vi = 105 VAC – 264 VAC
Io1 max @ Vi = 85 VAC – 105 VAC
droop hiccup
36.8
30
ADC
ADC
droop hiccup
limit
FNP/FXP1800-48G
Io1 max @ Vi = 180 VAC – 264 VAC
Io1 max @ Vi = 105 VAC – 180 VAC
Io1 max @ Vi = 85 VAC – 105 VAC
droop hiccup
droop hiccup
droop hiccup
43.8
36.8
30
ADC
ADC
ADC
output 1
Nominal current output 2
Current limit output 2
Static line regulation output 1
FNP1500-48G
Io2 nom @ Vi = 85 VAC – 264 VAC, Po 12 W
Io2 max @ Vi = 85 VAC – 264 VAC
Vi min - Vi max, 50 % Io nom
1.0
1.5
1.0
ADC
ADC
-0.5
0.5
% Vo nom
Vi = 230 V, 5-100 % Io nom
90.1
48
mV/A
VDC
Vo : full load (32.2 ADC) to no load
46.54
46.65
45.91
46.07
49.44
49.34
49.44
49.34
FXP1500-48G
Static load
regulation
FNP1800-48G
output 1
Vi = 230 V, 5-100 % Io nom
83.5
48
mV/A
VDC
Vo : full load (32.2 ADC) to no load
Vi = 230 V, 5-100 % Io nom
90.1
48
mV/A
VDC
Vo : full load (32.2 ADC) to no load
(droop
FXP1800-48G
characteristic)
Vi = 230 V, 5-100 % Io nom
83.5
48
mV/A
VDC
Vo : full load (32.2 ADC) to no load
Static load regulation
Vi = 230 V, 5-100 % Io nom
0.4
VDC
output 2 (droop characteristic)
Vo : full load (32.2 ADC) to no load
% Vo nom
Load change 50%<─>100% Io nom, dIo/dt =1 A/μs
Dynamic
Voltage deviation (droop + over- or undershoot)
load
FNP/FXP1500-48G
FNP/FXP1800-48G
All models
-5
5
% Vo nom
% Vo nom
μs
regulation
-5.7
5.7
400
Max. recovery time to within 1 % of Vo1 nom
Difference in current between two units for Vo1 above
10 % load.
Current
Share
FNP1500-48G
3.2
5.7
8
ADC
ADC
ADC
FXP1500-48G
FNP/FXP1800-48G
Start-up time
Time required for output within regulation
after initial application of AC-input (Vi nom, Io nom
)
1.5
s
after removal of inhibit (Vi nom, Io nom
)
100
ms
Vi nom, Io nom, 20 MHz bandwidth
Output voltage ripple and noise
(Filter 10 nF/10 µF)
480
120
mVpp
mVpp
Vo1
Vo2
Remote sense
Total compensation for cable losses
500
mV
DEC 12, 2006 revised to FEB 22, 2007
Page 5 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Protection
Parameter
Conditions/Description
Min
Nom
Max
Unit
Input fuse
Not user accessible
25A, fast blow
With NTCs
Inrush current limitation
Output
No-load -, short circuit - and overload proof
Tracking
Absolute
115
122
% Vo nom
Overvoltage protection latching1
59.5
V
Overtemperature protection
Automatic power shutdown at TC
95
°C
1 Remove input voltage to reset.
Control
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Conditions/Description
Status Indication
LEDs: DC OK (green), AC OK (green); fan fail and overtemperature (amber)
Monitors alarm functions and sets parameters
I2C digital bus
PS present pin
Contact closure to logic ground ( internal pull-down resistor of 1 kΩ)
TTL compatible signal, inhibited when open contact, high or at TTL logic “1”
Signal referenced to logic return (LRTN)
PS remote shutdown / Inhibit pin
Power supply OK (I2C)*
DC current fail (I2C)*
AC OK & DC OK & no overcurrent & no overtemperature & fans working
Overcurrent on Io1
Provides a warning that the input power has failed at least 5 ms before the
output falls out of regulation (<90% Vo1 set).
Open collector signal with 20 mA pull-down capability, referenced to logic
return (LRTN). AC fail will go high or open during power fail condition
and will go low when input is within the operating range. A Power Fail
warning will turn off the green AC OK LED.
AC fail / Power down warning
(I2C & OC)*
Internal undervoltage and overvoltage supervision of Vo1. Open collector signal with 20
mA pull-down capability, referenced to logic return (LRTN). DC fail will go high or open if
Vo1 is < 90% or > 110% of Vo1 set, measured in front of the ORing FETs. A green LED on
the front panel indicates normal operation. The LED will flash if in parallel operation Vo1 is
ok, but the unit is disabled.
DC fail / Output voltage fault
(I2C & OC)*
I2C critical temperature warning: Indicates that the operating temperature
has reached [Tshut-down – 10K]
I2C & OC overtemperature warning: Indicates if the unit is in overtemperature
shutdown. Open collector signal with 20 mA pull-down capability, referenced
to logic return (LRTN). The OC-output will go low 100 ms before an over-
temperature condition shuts down the unit. An amber LED on the front panel
indicates overtemperature or fan fail.
Temperature warning (I2C & OC)1
Monitors the voltage Vo1 at the output connector.
Accuracy ± 0.45 V over setting range, temperature and load.
DC voltage monitoring (I2C)1
DC current monitoring (I2C)1
Monitors the output current Io1 : Accuracy ± 0.4A over the load range.
DC voltage trimming
Output voltage trimming Vo1: ± 8 % of Vo set
Setting accuracy over I2C: ± 50mV at Vo nom, ± 150 mV over setting range
(I2C or external resistor)1
Two fan speed levels automatically set depending on the internal temperature.
The fan speed can be set to full speed or automatic control.
Fan speed control (I2C)1
Fan OK (I2C & OC)1
Synch. startup pin
Indicates if the fans are operating or have failed.
Overcurrent signal which can be used for synchronous startup of units in parallel or to
recover from an overload condition. (See application note).
1 Provided over the I2C interface or as an open collector signal on the output connector (OC).
For detailed Information on I2C, please see document “FNP1500-I2C-controlling.pdf” or use the Power-One I2C Management Interface
document.
DEC 12, 2006 revised to FEB 22, 2007
Page 6 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Output Connector Pinning and Signal Specification (12V Models)
Output
Connector
Pin
Location
Type
Low level
High level
U max
I max
Description
Overtemperature /
Fan Fail
< 0.4 V @ 20 mA
Pull up
15 V
20 mA
OC-output, protected by 16 V Zener diode and a
10 Ω resistor in series, referenced to logic GND
U1
U2
U3
U4
AC Fail /
Power down warning
OC-output, protected by 16 V Zener diode and a < 0.4 V @ 20 mA
15 V
20 mA
10 Ω resistor in series, referenced to logic GND
Pull up
Power Supply
Present
Open
Pull up
10 V
10 mA
Resistor (1 kꢀ) connected to logic GND
DC Fail /
Output voltage fault
OC-output, protected by 16 V Zener diode and a < 0.4 V @ 20 mA
15 V
20 mA
10 ꢀ resistor in series, referenced to logic GND
Pull up
Internal ground (Vo1– line before the output filter).
Do not connect the internal grounds in
systems with several units.
-
-
Internal ground
U5
ADDR0, I2C address
bus
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
T1
T2
T3
T4
T5
Internally pull up to 5V (10 kꢀ).
ADDR1, I2C address
bus
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
ADDR2, I2C address
bus
ADDR3, I2C address
bus
ADDR4, I2C address
bus
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
Switch closed
Switch open
5V
-
DIP switch or wire to internal ground,
Internally pull up to 5V (10 kꢀ).
I2C compatible signal
referenced to logic GND
I2C compatible signal
-
-
DATA, I2C data line
S1
S2
5 V or 3.3 V logic
5 V or 3.3 V logic
CLOCK, I2C clock
line
referenced to logic GND
-
-
-
-
-
-
Vo2 + output
Vo2 – output
S3
S4
Auxiliary power pin, insulated from main output
Auxiliary ground pin, insulated from main output
Internally connected over 10 ꢀ to Auxiliary GND.
Wire separately form Auxiliary - and main output
GND to minimize noise on signals and I2C.
Leave open if not used.
Logic ground
Output inhibit
S5
R1
PS active when pulled low
(DC-DC stage off when left open)
Referenced to logic GND
< 0.8 V
> 2.0 V
10 V
3.5 mA
Open or connected to Vo1+ at the load
(Internally connected to Vo1+ over 100 ꢀ)
dU < 3 Vpp
30 mA
V sense +
V sense -
R2
R3
Open or connected to Vo1- at the load
(Internally connected to Vo1- over 100 ꢀ)
dU < 3 Vpp
30 mA
Open or connected over resistor to internal
ground. Do not connect the margin pins in
systems with several units.
-
-
3 VDC
-
Output margin
Synch. Startup
R4
R5
-
-
12V
3mA
Open or connected to synch startup circuit,
referenced to Vo1 - at the output connector
P2, P4, P6,
P8, P10, P12
-
-
-
-
Vo1 + output
Vo1 – output
Main output + pins
Main output – pins
P1, P3, P5,
P7, P9, P11
DEC 12, 2006 revised to FEB 22, 2007
Page 7 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Output Connector Pinning and Signal Specification (48V Models)
Output Connector
Description
Pin
Location
Type
Low level
High level
V max
I max
Overtemperature /
Fan Fail
OC-output, protected by 16 V Zener diode and a 10 ꢀ
<0.4 V @ 20 mA
Pull up
15 V
20 mA
U1
U2
U3
U4
resistor in series, referenced to logic GND
OC-output, protected by 16 V Zener diode and a 10 ꢀ
<0.4 V @ 20 mA
Pull up
15 V
20 mA
AC Fail /
Power down warning
resistor in series, referenced to logic GND
Open
Pull up
10 V
10 mA
Resistor (1 kꢀ) connected to logic GND
Power Supply Present
OC-output, protected by 16 V Zener diode and a 10 ꢀ
<0.4 V @ 20 mA
Pull up
15 V
20 mA
DC Fail /
Output voltage fault
resistor in series, referenced to logic GND
Internal ground (Vo1– line before the output filter).
Do not connect the internal grounds in
systems with several units.
-
-
Internal ground
U5
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
ADDR0, I2C address bus
ADDR1, I2C address bus
ADDR2, I2C address bus
ADDR3, I2C address bus
T1
T2
T3
T4
Internally pull up to 5V (10 kꢀ).
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
DIP switch or wire to internal ground,
Switch closed
Switch open
5V
-
Internally pull up to 5V (10 kꢀ).
Switch closed
Switch open
5V
-
DIP switch or wire to internal ground,
ADDR4, I2C address bus
T5
Internally pull up to 5V (10 kꢀ).
I2C compatible signal
referenced to logic GND
I2C compatible signal
-
-
DATA, I2C data line
S1
S2
5 V or 3.3 V logic
5 V or 3.3 V logic
CLOCK, I2C clock line
referenced to logic GND
-
-
-
-
-
-
Auxiliary power +12 V
Auxiliary power ground
S3
S4
Vo2+ output, insulated from main output
Vo2 - output, insulated from main output
Internally connected over 10 ꢀ to Auxiliary GND.
Wire separately form Auxiliary - and main output GND
to minimize noise on signals and I2C. Leave open if not
used.
Logic ground
Output inhibit
S5
R1
PS active when pulled low
(DC-DC stage off when left open)
Referenced to logic GND
<0.8 V
>2.0 V
10 V
3.5 mA
Open or connected to Vo1+ at the load
(Internally connected to Vo1+ over 100 ꢀ)
dV < 3 Vpp
30 mA
V sense +
V sense -
R2
R3
Open or connected to Vo1- at the load
(Internally connected to Vo1- over 100 ꢀ)
dV < 3 Vpp
30 mA
Open or connected to internal ground
(+8 % Vo1) or V sense+ (-8 % Vo1)
Do not connect the margin pins in
systems with several units.
-
-
60V
-
Output margin
Synch. Startup
R4
R5
-
-
12V
Open or connected to synch startup circuit,
referenced to Vo1 - at the output connector
2mA
-
-
-
-
Vo1
Vo1
-
P1, P3, P5
P2, P4, P6
Main output – pins
Main output + pins
+
Fulcrum:
The handle has been designed to allow easy plug-in and -out in a rack system. The handle (lever) fits into a counter piece
(fulcrum) which is fixed to the bottom of the rack. During the plug, the fulcrum holds the unit down and guides it towards the
output connector. The Power-One part number of the fulcrum and its associated mounting accessories is: HZZ01223.
DEC 12, 2006 revised to FEB 22, 2007
Page 8 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Mechanical Data
FNP1500/1800 Mechanical Data (H, W, D)
1.6” (40.6 mm) x 5.6” (142.2 mm) x 11” (279.4 mm)
1.6” (40.6 mm) x 5.6” (142.2 mm) x 12” (304.8 mm)
FXP1500/1800 Mechanical Data (H, W, D)
Note: FNP1500/1800's have only 11" (279.4 mm) depth
Output Connector Descriptions (12V Models)
Rear View
Connector: FCI (51732-026 LF)
Female ledge connector:
Right Angle type: Part No. FCI (manufacturer): 51762-11202000AA LF; Power-One Part No.: ZES260-G
Vertical type: Part No. FCI (manufacturer): 51742-11202000AA LF; Power-One Part No.: ZES282-G
Manufacturer: FCI
Information on availability of FCI connectors under http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp
IEC AC power cord with C19 connector VDE 16A: Interpower Components Ltd. 70009110250
IEC AC power cord with C19 connector UL 20A: Interpower Components Ltd. 70025110250
DEC 12, 2006 revised to FEB 22, 2007
Page 9 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
FNP1500/1800 (48V Model) Output Connector
Descriptions
Rear View
Connector: FCI (51732-020 LF)
Female ledge connector:
Right Angle type: Part No. FCI (manufacturer): 51762-106020000AA LF; Power-One Part No.: ZES258-G
Vertical type: Part No. FCI (manufacturer): 51742-106020000AA LF; Power-One Part No.: ZES271-G
Manufacturer: FCI
Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp
FXP1500/1800 (48V Model) Input and Output Connector Descriptions
Output con.: FCI (51732-020 LF)
Input con.: FCI (51939-126 LF)
Rear View
Female ledge connector: Manufacturer: FCI
Output connector Part No.: 51762-106020000AA LF (Horizontal)
Output connector Part No.: 51742-106020000AA LF (Vertical)
Input connector Part No.: 51915-056LF (Horizontal)
Input connector Part No.: 51940-099LF (Vertical)
Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp
Paralleling Front-Ends:
For parallel use in minimal configuration systems, only the inhibit pins must be shorted to logic GND. All other pins can be left
open. The power supplies will share the output current automatically (droop current share).
For parallel applications without I2C bus, but the use of all other features, it is recommended to connect all logic GND’s on a
backplane together, to connect all Vo2 -, all V o2 + and to leave the internal GND’s open.
The sense wires can be left open or connected to a common load point, the synch-start pin can be left open or connected to a
synch-start circuit, the inhibit pins can be connected together or used individually. All I2C signals (T1-T5, S1, and S2) can be left
open.
Use of a small foil capacitor > 3µF directly at the power outputs of each unit is recommended in order to prevent voltage drops at
the hot plug. For additional information on paralleling see the following Rack (Power Shelf) section.
DEC 12, 2006 revised to FEB 22, 2007
Page 10 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Racks
(FNR-3-12G, FXR-3-12G, FNR-3-48G, and FXR-3-48G Power Shelves)
Each rack (power shelf) is 1U high with backplane and designed for up to three front-end models in parallel or in n+1 operation.
Each power shelf has:
•
•
•
•
Massive copper bus bars for low-loss current distribution.
Output terminals with two M4-screws on each power tab.
Two fast-on contacts for system earthing.
Address coding over five pole DIP switch on each unit, 37-pin D-Sub connector with I2C-lines, monitoring signals and
support functions.
•
Provides a start-up synchronization circuit and EMV filters.
FNR-3-12G and FNR-3-48G Power Shelf Front View
FXR-3-12G and FXR-3-48G Power Shelf Front View
Overall Mechanical Dimensions (FNR-3-12G and FNR-3-48G Power Shelves)
FNR-3 Mechanical Data (W, H, D)
FXR-3 Mechanical Data (W, H, D)
17.7” (449.6 mm) x 1.7” (43.1 mm) x 13” (330.2 mm)
17.7” (449.6 mm) x 1.7” (43.1 mm) x 14” (355.6 mm)
DEC 12, 2006 revised to FEB 22, 2007
Page 11 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Output Connector Descriptions (FNR-3-12G and FNR-3-48G)
F
D
A
E
C
G
H
B
I
Location
Description
5-Bit DIP switch for I2C addressing of PSU 1
A
B
C
D
E
F
G
H
I
Earth connection
Earth connection
Earth connection
Output 1 minus
Output 1 plus
5-Bit DIP switch for I2C addressing of PSU 2
37-pin SUB-D connector, controlling and auxiliary power (output 2)
5-Bit DIP switch for I2C addressing of PSU 3
Output Connector Descriptions (FXR-3-12G and FXR-3-48G)
PE3
PE2
PE1
L3
N3
L2 N2
L1
N1
A
B
C
D
E
F
G
H
I
J
Location
Description
Earth connection
5-bit DIP switch for I2C addressing of PSU #3
Mains connector of PSU #3
Output 1 Minus
A
B
C
D
E
F
G
H
I
Output 1 Plus
5-bit DIP switch for I2C addressing of PSU #2
Mains connector of PSU #2
37-pin SUB-D connector, control, sense, check and Auxiliary power (Output 2)
5-bit DIP switch for I2C addressing of PSU #1
J
Mains connector of PSU #1
DEC 12, 2006 revised to FEB 22, 2007
Page 12 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Mechanical Data (FNR-3-12G and FNR-3-48G Power Shelves)
(To Be Supplied)
Mechanical Data (FXR-3-12G and FXR-3-48G Power Shelves)
DEC 12, 2006 revised to FEB 22, 2007
Page 13 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
Accessories:
Center Angular Brackets are set in the middle for shelf mounting:
Center Angular Bracket sets can be ordered: Power-One part no.: HZZ01222
Note: Each Center Angular Bracket set contains 2 brackets and 8 screws.
Fulcrums:
Individual fulcrum sets can be also ordered: Power-One part no.: HZZ01223.
Note: Each HZZ01223 set contain 2 fulcrums, 2 supports, and mounting accessories.
DEC 12, 2006 revised to FEB 22, 2007
Page 14 of 15
www.power-one.com
FNP1500/1800 and FXP1500/1800 Front-Ends
& FNR-3 and FXR-3 Power Shelves Data Sheet
I2C to USB Interface HZZ02002G:
I2C <to>USB
Interface
An I2C to RS232 Interface can be ordered from Power-One. The interface part number to order is HZZ02002G.
All FNP/FXP front-ends can be controlled via Power-One's GUI-driven I2C Management software and the I2C-to-USB interface.
An I2C Programming Manual describes the complete range of parameters that can be programmed to the FNP and
FXP1500/1800 front-ends. This manual is available by searching on "FNP1500" at www.power-one.com.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent
of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
DEC 12, 2006 revised to FEB 22, 2007
Page 15 of 15
www.power-one.com
相关型号：
©2020 ICPDF网 联系我们和版权申明