PMP25 [POWER-ONE]
Rectifier Module; 整流模块
| 型号： | PMP25 |
| 厂家： | 
POWER-ONE |
| 描述： | Rectifier Module |
| 文件： | 总2页 (文件大小：103K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PMP 25
Rectifier Module
Description
The Power-One PMP 25 rectifier uses
resonance switch mode technology (soft
switching), and incorporates thermal
protection while providing extremely reliable
DC power in a small space. Rectifier
communication is accomplished using digital
interfaces over an RS485 data bus.
Information is transmitted to adjacent
rectifiers while providing status and
identification information to the system
controller (PCS).
At only 4 rack units high, these compact
rectifiers allow for up to five modules in each
23in. rack (4 units in 19in. rack) providing up
to 250A at 48V or up to 550A at 24V. With
full power available up to 65°C, PMP 25
rectifiers are ideal for any indoor or outdoor
application.
Features
•
•
•
•
•
•
•
•
•
Compact 4 rack-unit height
50A output at 48V
110A output at 24V
208 / 240 single phase input
Input over-voltage disconnect
Hot-swappable rectifiers
High efficiency, up to 91%
Active current sharing
International standards compliance
PPS 25 System
Shown
www.power-one.com
PMP 25
Rectifier Module
Input
Model
Mechanical
Dimensions
105 x 176 x 455mm
(6.9 x 4.13 x 17.9in.)
PMP 25.24
PMP 25.48
196 - 250V AC ±10% single phase,
(44-66Hz)
Input
Weight
6.2kg (13.6lbs.)
Voltage
176-160V AC at reduced output power
Current
(max.)
Cooling
Interface
Fan: speed controlled and monitored
<22A
<20A
RS485 for communication with the
supervision module
Soft Start
<22A
<20A
EN 61000-3-2
Reinforced insulation tested at:
4.25 kV DC primary-secondary,
2.12 kV DC primary-ground,
0.75 kV DC secondary ground
Harmonics
Power Factor >0.98 at 50-100% load
Insulation
Surge
EN 61000-4-5
Immunity
Enclosure
Mounting
IP20
Fuse
F 25A
In 19”/ 4U subrack up to 4
In 23”/ 4U subrack up to 5
Connection Harting MH - 21 Signal pins, 3 HC pins
EN 61000-6-2, EN 61000-6-3,
EMC
Other Technical Data
FCC Part 15 Class B
EN 60950
Safety
CSA C22-2 No. 950, UL 1950
Output
Short circuit proof, automatic current
limiting, selective shutdown of
modules at excessive output voltage.
Thermal protection reduces the
output power at environmental
temperatures above maximum level.
Shut down at >75°C with automatic
restart.* Input over-voltage
Model
PMP 25.24
PMP 25.48
Power (max.)
3080W
2800W
Protection
Indications
Output Voltage 22-30V DC
Current (max.) 110A
44-58V DC
50A
disconnection at >275VAC with
automatic reset at >260VAC.
Efficiency
>89%
>91%
(@ 40-90%Load)*
Green LED
Yellow LED
Power ON
Tolerance
Vout +/- 0.5%
Thermal Protection
Transient
Response
+/- 6% at load variation 10-90%
or 90-10%, recovery time 150ms
Yellow Flashing Comm. Error
Red LED
<60dBA
Module Failure
Load Sharing
Ripple
<5% of nominal current
<100mV p-p (BW. 30MHz)
<2mV, according to CCITT norms
8mm HC-pins
Audible
Noise
Operating
48V: -25 to +60°C
24V: -40 to +65°C
Temperature*
Psophometric
Connection
EMC
Storage
-40 to +85°C
Temperature
EN 61000-6-2, EN 61000-6-3,
FCC Part 15, Class B
Radiated EMC
Environment
EN 61000-6-2, EN 61000-6-4
Storage:
ETS 300 019-2-1
* Average performance for a single rectifier
Transport:
Operation:
ETS 300 019-2-2
ETS 300 019-2-3
Note: All specifications are subject to change without notification.
www.power-one.com
11V0005-029 PMP 25 V3.0
相关型号：
©2020 ICPDF网 联系我们和版权申明