TOP225PN [POWERINT]
Three-Terminal Off-Line PWM Switch;型号: | TOP225PN |
厂家: | Power Integrations |
描述: | Three-Terminal Off-Line PWM Switch |
文件: | 总20页 (文件大小:1537K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
This product is not recommended for new designs.
TOP221-227
TOPSwitch-II Family
Three-Terminal Off-Line PWM Switch
Product Highlights
AC
IN
• Lowest cost, lowest component count switcher solution
• Cost competitive with linears above 5 W
• Very low AC/DC losses – up to 90% efficiency
• Built-in Auto-restart and Current limiting
• Latching Thermal shutdown for system level protection
• Implements Flyback, Forward, Boost or Buck topology
• Works with primary or opto feedback
• Stable in discontinuous or continuous conduction mode
• Source connected tab for low EMI
D
S
CONTROL
C
TOPSwitch
• Circuit simplicity and Design Tools reduce time to market
Description
PI-1951-091996
The second generation TOPSwitch™-II family is more cost
effective and provides several enhancements over the first
generation TOPSwitch family. The TOPSwitch-II family
extends the power range from 100W to 150W for 100/115/
230 VAC input and from 50W to 90W for 85-265 VAC univer-
sal input. This brings TOPSwitch technology advantages
to many new applications, i.e. TV, Monitor, Audio amplifiers,
etc. Many significant circuit enhancements that reduce the
sensitivity to board layout and line transients now make the
design even easier. The standard 8L PDIP package option
Figure 1. Typical Flyback Application.
reduces cost in lower power, high efficiency applications.
The internal lead frame of this package uses six of its pins to
transfer heat from the chip directly to the board, eliminating
the cost of a heat sink. TOPSwitch incorporates all functions
necessary for a switched mode control system into a three
terminal monolithic IC: power MOSFET, PWM controller, high
voltage start up circuit, loop compensation and fault protec-
tion circuitry.
Output Power Table
TO-220 (Y) Package1
8L PDIP (P) or 8L SMD (G) Package2
Wide Range Input
85 to 265 VAC
Single Voltage Input3
Single Voltage Input3
100/115/230 VAC 15ꢀ
Wide Range Input
85 to 265 VAC
PART
ORDER
NUMBER
PART
ORDER
NUMBER
100/115/230 VAC 15ꢀ
4,6
4,6
5,6
5,6
PMAX
PMAX
PMAX
PMAX
12 W
25 W
7 W
TOP221YN
TOP222YN
TOP223YN
TOP224YN
TOP225YN
TOP226YN
TOP227YN
9 W
6 W
TOP221PN or TOP221GN
TOP222PN or TOP222GN
15 W
30 W
45 W
60 W
75 W
90 W
15 W
25 W
30 W
10 W
15 W
20 W
TOP223PN or TOP223GN
TOP224PN or TOP224GN
50 W
75 W
100 W
125 W
150 W
Notes: 1. Package outline: TO-220/3 2. Package Outline: DIP-8 or SMD-8 3. 100/115 VAC with doubler input 4. Assumes appro-
priate heat sinking to keep the maximum TOPSwitch junction temperature below 100 °C. 5. Soldered to 1 sq. in. (6.45 cm2), 2 oz.
copper clad (610 gm/m2) 6. PMAX is the maximum practical continuous power output level for conditions shown. The continuous
power capability in a given application depends on thermal environment, transformer design, efficiency required, minimum spec-
ified input voltage, input storage capacitance, etc. 7. Refer to key application considerations section when using TOPSwitch-II in
an existing TOPSwitch design.
www.power.com
August 2016
This Product is Covered by Patents and/or Pending Patent Applications.
TOP221-227
ꢐ
ꢋ
ꢛ
1
ꢋOꢅTꢈOꢌ
ꢃꢈꢇꢎꢅ
ꢎꢅTꢉꢈꢅꢇꢌ
ꢀꢂPPꢌꢑ
ꢙ
ꢋ
ꢀꢁꢂTꢃOꢄꢅꢆ
ꢇꢂTO-ꢈꢉꢀTꢇꢈT
ꢀꢁꢂꢅT ꢈꢉꢏꢂꢌꢇTOꢈꢆ
ꢉꢈꢈOꢈ ꢇꢊPꢌꢎꢗꢎꢉꢈ
ꢖ
-
∏ ꢚ
-
ꢒꢓ7 ꢐ
ꢔꢓ7 ꢐ
ꢒꢓ7 ꢐ
ꢖ
ꢖ
-
ꢐ
ꢎ
ꢌꢎꢊꢎT
ꢎ
ꢗꢘ
Tꢁꢉꢈꢊꢇꢌ
ꢀꢁꢂTꢃOꢄꢅ
ꢆ
R
ꢇ
POꢄꢉꢈ-ꢂP
ꢈꢉꢀꢉT
ꢇ
ꢋOꢅTꢈOꢌꢌꢉꢃ
Tꢂꢈꢅ-Oꢅ
ꢏꢇTꢉ
ꢃꢈꢎꢐꢉꢈ
OꢀꢋꢎꢌꢌꢇTOꢈ
ꢃ
ꢊꢇꢕ
ꢋꢌOꢋꢍ
ꢀꢇꢄ
ꢆ
ꢇ
ꢇ
-
ꢌꢉꢇꢃꢎꢅꢏ
ꢉꢃꢏꢉ
ꢖ
R
ꢘꢌꢇꢅꢍꢎꢅꢏ
Pꢄꢊ
ꢋOꢊPꢇꢈꢇTOꢈ
ꢊꢎꢅꢎꢊꢂꢊ
Oꢅ-Tꢎꢊꢉ
ꢃꢉꢌꢇꢑ
ꢈ
ꢉ
ꢀOꢂꢈꢋꢉ
ꢀꢁꢂ1ꢃꢄꢅꢂ0ꢃ16ꢃ6
Figure 2. Functional Block Diagram.
Pin Functional Description
DRAIN Pin:
Tꢋꢕ ꢆꢖꢗꢏꢘꢖꢋꢙꢙꢚ
ꢀꢛꢖꢖꢏꢌꢗꢏꢜ ꢗꢛ ꢇOꢈꢂꢀꢉ Pꢝꢖ
Output MOSFET drain connection. Provides internal bias
current during start-up operation via an internal switched
high-voltage current source. Internal current sense point.
ꢄꢂꢅꢆꢁ
ꢇOꢈꢂꢀꢉ
CONTROL Pin:
ꢀOꢁTꢂOꢃ
Error amplifier and feedback current input pin for duty cycle
control. Internal shunt regulator connection to provide inter-
nal bias current during normal operation. It is also used as
the connection point for the supply bypass and auto-restart/
compensation capacitor.
ꢊ Pꢋꢌꢍꢋꢎꢏ ꢐTO-22ꢑꢒꢓꢔ
ꢇ
ꢇ
ꢇ ꢐꢞꢟ ꢂTꢁꢔ
1
2
ꢠ
7
SOURCE Pin:
ꢇ ꢐꢞꢟ ꢂTꢁꢔ
ꢇ ꢐꢞꢟ ꢂTꢁꢔ
ꢄ
YN package – Output MOSFET source connection for high
voltage power return. Primary side circuit
common and reference point.
2
ꢤ
ꢥ
ꢣ
ꢇ
ꢀ
PN and GN package – Primary-side control circuit common
and reference point.
P Pꢋꢌꢍꢋꢎꢏ ꢐꢄꢆP-ꢠꢔ
ꢡ Pꢋꢌꢍꢋꢎꢏ ꢐꢇꢢꢄ-ꢠꢔ
ꢀꢁꢂꢃ08ꢄꢂ0ꢄ0ꢄ01
SOURCE (HV RTN) Pin: (P and G package only)
Output MOSFET source connection for high voltage power
return.
Figure 3. Pin Configuration.
2
Rev. G 08/16
www.power.com
TOP221-227
ꢔꢋꢕꢖꢌ ꢗ Pꢘꢁ ꢙꢚꢛꢜ
ꢓꢑꢒ
TOPSwitch-II Family Functional Description
TOPSwitch is a self biased and protected linear control cur-
rent-to-duty cycle converter with an open drain output. High
efficiency is achieved through the use of CMOS and integra-
tion of the maximum number of functions possible. CMOS
process significantly reduces bias currents as compared to
bipolar or discrete solutions. Integration eliminates external
power resistors used for current sensing and/or supplying
initial start-up bias current.
ꢂꢆꢇꢕ-ꢞꢌꢟꢇꢚꢞꢇ
ꢄ
ꢝ
ꢀ
ꢁꢂꢃ
During normal operation, the duty cycle of the internal output
MOSFET decreases linearly with increasing CONTROL pin
current as shown in Figure 4. To implement all the required
control, bias, and protection functions, the DRAIN and CON-
TROL pins each perform several functions as described
below. Refer to Figure 2 for a block diagram and to Figure 6
for timing and voltage waveforms of the TOPSwitch inte-
grated circuit.
ꢀ
ꢁꢄꢅ
ꢄ
2ꢑꢒ
ꢉꢀ1
ꢄ
ꢍꢐꢂꢏ
ꢉ
ꢀꢁꢂꢃ0ꢄ0ꢂ0ꢅ01ꢆꢇ
Figure 4. Relationship of Duty Cycle to CONTROL Pin Current.
5.7 V
4.7 V
V
C
0
V
IN
DRAIN
0
5.7 V
4.7 V
V
C
0
V
IN
DRAIN
0
C is the total external capacitance
T
connected to the CONTROL pin
Figure 5. Start-up Waveforms for (a) Normal Operation and (b) Auto-restart.
3
Rev. G 08/16
www.power.com
TOP221-227
Oscillator
TOPSwitch-II Family Functional Description (cont.)
The internal oscillator linearly charges and discharges the
internal capacitance between two voltage levels to create a
sawtooth waveform for the pulse width modulator. The oscil-
lator sets the pulse width modulator/current limit latch at the
beginning of each cycle. The nominal frequency of 100 kHz
was chosen to minimize EMI and maximize efficiency in
power supply applications. Trimming of the current reference
improves the frequency accuracy.
Control Voltage Supply
CONTROL pin voltage VC is the supply or bias voltage for the
controller and driver circuitry. An external bypass capacitor
closely connected between the CONTROL and SOURCE
pins is required to supply the gate drive current. The total
amount of capacitance connected to this pin (CT) also sets
the auto-restart timing as well as control loop compensation.
VC is regulated in either of two modes of operation. Hyster-
etic regulation is used for initial start-up and overload opera-
tion. Shunt regulation is used to separate the duty cycle
error signal from the control circuit supply current. During
start-up, CONTROL pin current is supplied from a high-volt-
age switched current source connected internally between
the DRAIN and CONTROL pins. The current source pro-
vides sufficient current to supply the control circuitry as well
as charge the total external capacitance (CT).
Pulse Width Modulator
The pulse width modulator implements a voltage-mode
control loop by driving the output MOSFET with a duty cycle
inversely proportional to the current into the CONTROL pin
which generates a voltage error signal across RE. The error
signal across RE is filtered by an RC network with a typical
corner frequency of 7 kHz to reduce the effect of switching
noise. The filtered error signal is compared with the internal
oscillator sawtooth waveform to generate the duty cycle
waveform. As the control current increases, the duty cycle
decreases. A clock signal from the oscillator sets a latch
which turns on the output MOSFET. The pulse width modu-
lator resets the latch, turning off the output MOSFET. The
maximum duty cycle is set by the symmetry of the internal
oscillator. The modulator has a minimum ON-time to keep
the current consumption of the TOPSwitch independent
of the error signal. Note that a minimum current must be
driven into the CONTROL pin before the duty cycle begins to
change.
The first time VC reaches the upper threshold, the high-
voltage current source is turned off and the PWM modulator
and output transistor are activated, as shown in Figure 5(a).
During normal operation (when the output voltage is regulat-
ed) feedback control current supplies the VC supply current.
The shunt regulator keeps VC at typically 5.7 V by shunting
CONTROL pin feedback current exceeding the required DC
supply current through the PWM error signal sense resistor
RE. The low dynamic impedance of this pin (ZC) sets the
gain of the error amplifier when used in a primary feedback
configuration. The dynamic impedance of the CONTROL
pin together with the external resistance and capacitance
determines the control loop compensation of the power
system.
Gate Driver
The gate driver is designed to turn the output MOSFET on at
a controlled rate to minimize common-mode EMI. The gate
drive current is trimmed for improved accuracy.
If the CONTROL pin total external capacitance (CT) should
discharge to the lower threshold, the output MOSFET is
turned off and the control circuit is placed in a low-current
standby mode. The high-voltage current source turns on
and charges the external capacitance again. Charging
current is shown with a negative polarity and discharging
current is shown with a positive polarity in Figure 6. The
hysteretic auto-restart comparator keeps VC within a window
of typically 4.7 to 5.7 V by turning the high-voltage current
source on and off as shown in Figure 5(b). The auto-restart
circuit has a divide-by-8 counter which prevents the output
MOSFET from turning on again until eight discharge-charge
cycles have elapsed. The counter effectively limits
Error Amplifier
The shunt regulator can also perform the function of an er-
ror amplifier in primary feedback applications. The shunt
regulator voltage is accurately derived from the temperature
compensated bandgap reference. The gain of the error
amplifier is set by the CONTROL pin dynamic impedance.
The CONTROL pin clamps external circuit signals to the VC
voltage level. The CONTROL pin current in excess of the
supply current is separated by the shunt regulator and flows
through RE as a voltage error signal.
Cycle-By-Cycle Current Limit
TOPSwitch power dissipation by reducing the auto-restart
duty cycle to typically 5%. Auto-restart continues to cycle
until output voltage regulation is again achieved.
The cycle by cycle peak drain current limit circuit uses the
output MOSFET ON-resistance as a sense resistor. A current
limit comparator compares the output MOSFET ON-state
drain-source voltage, VDS(ON) with a threshold voltage. High
drain current causes VDS(ON) to exceed the threshold voltage
and turns the output MOSFET off until the start of the next
clock cycle. The current limit comparator threshold voltage
is temperature compensated to minimize variation of the
effective peak current limit due to temperature related
Bandgap Reference
All critical TOPSwitch internal voltages are derived from a
temperature-compensated bandgap reference. This refer-
ence is also used to generate a temperature-compensated
current source which is trimmed to accurately set the oscilla-
tor frequency and MOSFET gate drive current.
changes in output MOSFET RDS(ON)
.
4
Rev. G 08/16
www.power.com
TOP221-227
V
IN
V
IN
0
DRAIN
V
OUT
0
0
I
OUT
• • •
• • •
V
V
C
C(reset)
0
0
• • •
• • •
I
C
Figure 6. Typical Waveforms for (1) Normal Operation, (2) Auto-restart, and (3) Power Down Reset.
The leading edge blanking circuit inhibits the current limit
comparator for a short time after the output MOSFET is
turned on. The leading edge blanking time has been set so
that current spikes caused by primary-side capacitances
and secondary-side rectifier reverse recovery time will not
cause premature termination of the switching pulse.
Overtemperature Protection
Temperature protection is provided by a precision analog
circuit that turns the output MOSFET off when the junction
temperature exceeds the thermal shutdown temperature
(typically 135 °C). Activating the power-up reset circuit by
removing and restoring input power or momentarily pulling
the CONTROL pin below the power-up reset threshold resets
the latch and allows TOPSwitch to resume normal power
supply operation. VC is regulated in hysteretic mode and a
4.7 V to 5.7 V (typical) sawtooth waveform is present on the
CONTROL pin when the power supply is latched off.
The current limit can be lower for a short period after the
leading edge blanking time as shown in Figure 12. This is
due to dynamic characteristics of the MOSFET. To avoid trig-
gering the current limit in normal operation, the drain current
waveform should stay within the envelope shown.
High-Voltage Bias Current Source
This current source biases TOPSwitch from the DRAIN pin
and charges the CONTROL pin external capacitance (CT)
during start-up or hysteretic operation. Hysteretic opera-
tion occurs during auto-restart and overtemperature latched
shutdown. The current source is switched on and off with an
effective duty cycle of approximately 35%. This duty cycle
is determined by the ratio of CONTROL pin charge (IC) and
discharge currents (ICD1 and ICD2). This current source is
turned off during normal operation when the output MOSFET
is switching.
Shutdown/Auto-restart
To minimize TOPSwitch power dissipation, the shutdown/
auto-restart circuit turns the power supply on and off at an
auto-restart duty cycle of typically 5% if an out of regulation
condition persists. Loss of regulation interrupts the external
current into the CONTROL pin. VC regulation changes from
shunt mode to the hysteretic auto-restart mode described
above. When the fault condition is removed, the power sup-
ply output becomes regulated, VC regulation returns to shunt
mode, and normal operation of the power supply resumes.
5
Rev. G 08/16
www.power.com
TOP221-227
ꢑ1
ꢆ.ꢆ µꢒ
ꢉꢃ
ꢊꢋꢄꢅ01
ꢑꢒ ꢓ
ꢄTꢏ
ꢌꢃ
ꢌꢆ
ꢑ
ꢆꢆ0 µꢋ
100 µꢋ
Rꢆ
ꢅꢇ ꢈΩ
ꢌ1
ꢃ.ꢃ ꢍꢋ
1 ꢈꢎ
ꢎR1
10 ꢎ
10 ꢎ
ꢉ1
ꢊꢋꢅ00ꢄ
Rꢃ
100 Ω
ꢉꢆ
1ꢓꢅ1ꢅ8
R1
10 Ω
ꢀꢁꢂꢃ-ꢄꢅꢆꢇꢃ
ꢈꢉ ꢊꢆꢋꢌꢍ
ꢏ1
ꢑ
TOPꢎꢔꢁꢍꢕꢖ-ꢊꢊ
ꢊ1
ꢌꢅ
100 µꢋ
16 ꢎ
ꢈ
ꢏꢐꢀꢃꢃ1ꢀ
ꢉOꢏTꢄOꢐ
ꢉ
ꢊꢃ
ꢀꢌ81ꢇꢔ
12 ꢓ ꢏꢗꢆ-ꢊꢘꢗꢙꢅꢍꢃꢂ
ꢌꢄ
ꢅꢇ µꢋ
10 ꢎ
ꢎ
-
-
ꢀꢁꢂꢃ11ꢄꢂ0ꢅ0ꢅ01
Figure 7. Schematic Diagram of a 4 W TOPSwitch-II Standby Power Supply using an 8 lead PDIP.
Application Examples
the full universal AC input range. The TOP221 is packaged in
an 8 pin power DIP package.
Following are just two of the many possible TOPSwitch
implementations. Refer to the Data Book and Design Guide
for additional examples.
The output voltage (5 V) is directly sensed by the Zener
diode (VR1) and the optocoupler (U2). The output voltage is
determined by the sum of the Zener voltage and the volt-
age drop across the LED of the optocoupler (the voltage
drop across R1 is negligible). The output transistor of the
optocoupler drives the CONTROL pin of the TOP221. C5
bypasses the CONTROL pin and provides control loop com-
pensation and sets the auto-restart frequency.
4 W Standby Supply using 8 Lead PDIP
Figure 7 shows a 4 W standby supply. This supply is used
in appliances where certain standby functions (e.g. real time
clock, remote control port) must be kept active even while
the main power supply is turned off.
The 5 V secondary is used to supply the standby function
and the 12 V non-isolated output is used to supply power
for the PWM controller of the main power supply and other
primary side functions.
The transformer’s leakage inductance voltage spikes are
snubbed by R3 and C1 through diode D1. The bias winding
is rectified and filtered by D3 and C4 providing a non-isolat-
ed 12 V output which is also used to bias the collector of the
optocoupler’s output transistor. The isolated 5 V output wind-
ing is rectified by D2 and filtered by C2, L1 and C3.
For this application the input rectifiers and input filter are
sized for the main supply and are not shown. The input DC
rail may vary from 100 V to 380 V DC which corresponds to
6
Rev. G 08/16
www.power.com
TOP221-227
ꢗ1
ꢅ.ꢅ µꢙ
ꢇꢃ
ꢈꢉRꢊꢃ0
ꢌ12 ꢍ
ꢅTꢁ
ꢌꢃ
ꢅꢅ0 µꢍ
ꢅꢎ ꢏ
ꢌꢅ
ꢃꢃ0 µꢍ
ꢅꢎ ꢏ
ꢏR1
ꢀ6ꢓꢔꢃ00
ꢇ1
ꢑꢒꢏꢃ6ꢌ
ꢑR1
ꢊ00 ꢏ
ꢗꢃ
ꢃꢃ ꢘꢙ
ꢇꢅ
1ꢋꢊ1ꢊ8
R1
ꢌ1
100 Ω
ꢊꢆ µꢍ
ꢌꢊ
0.1 µꢍ
ꢊ00 ꢏ
TOPꢃꢆꢇꢈꢉꢊ-ꢋꢋ
ꢌ6
Rꢃ
ꢉ1
ꢂ
ꢃ
0.1 µꢍ
ꢐ1
ꢃꢃ0 Ω
ꢐꢚꢀꢃꢃꢊꢀ
ꢄ
ꢄOꢁTꢅOꢀ
ꢃꢎ0 ꢏꢕꢌ
ꢉꢃ
ꢀꢌ81ꢆꢕ
Rꢅ
6.8 Ω
ꢍ1
ꢅ.1ꢎ ꢕ
ꢏRꢃ
1ꢋꢎꢃꢊ1ꢑ
11 ꢏ
ꢌꢆ
1 ꢛꢍ
ꢃꢎ0 ꢏꢕꢌ
ꢒ1
ꢖ1
ꢌꢎ
ꢊꢆ µꢍ
ꢀ
ꢁ
ꢀꢁꢂꢃ01ꢄꢂ0ꢅꢅ1ꢄꢆ
Figure 8. Schematic Diagram of a 20 W Universal Input TOPSwitch-II Power Supply using an 8 lead PDIP.
20 W Universal Supply using 8 Lead PDIP
VR1 clamp leading-edge voltage spikes caused by trans-
former leakage inductance. The power secondary winding
is rectified and filtered by D2, C2, L1, and C3 to create the
12 V output voltage. R2 and VR2 provide a slight pre-load
on the 12 V output to improve load regulation at light loads.
The bias winding is rectified and filtered by D3 and C4 to
create a TOPSwitch bias voltage. L2 and Y1-safety capaci-
tor C7 attenuate common mode emission currents caused
by high-voltage switching waveforms on the DRAIN side of
the primary winding and the primary to secondary capaci-
tance. Leakage inductance of L2 with C1 and C6 attenu-
ates differential-mode emission currents caused by the
fundamental and harmonics of the trapezoidal or triangular
primary current waveform. C5 filters internal MOSFET gate
drive charge current spikes on the CONTROL pin, deter-
mines the auto-restart frequency, and together with R1 and
R3, compensates the control loop.
Figure 8 shows a 12 V, 20 W secondary regulated flyback
power supply using the TOP224P in an eight lead PDIP
package and operating from universal 85 to 265 VAC input
voltage. This example demonstrates the advantage of the
higher power 8 pin leadframe used with the TOPSwitch-II
family. This low cost package transfers heat directly to the
board through six source pins, eliminating the heatsink and
the associated cost. Efficiency is typically 80% at low line
input. Output voltage is directly sensed by optocoupler U2
and Zener diode VR2. The output voltage is determined by
the Zener diode (VR2) voltage and the voltage drops across
the optocoupler (U2) LED and resistor R1. Other output
voltages are possible by adjusting the transformer turns ratio
and value of Zener diode VR2.
AC power is rectified and filtered by BR1 and C1 to create
the high voltage DC bus applied to the primary winding of
T1. The other side of the transformer primary is driven by
the integrated TOPSwitch-II high-voltage MOSFET. D1 and
7
Rev. G 08/16
www.power.com
TOP221-227
Key Application Considerations
General Guidelines
• Short interruptions of AC power may cause TOPSwitch
to enter the 8-count auto-restart cycle before starting
again. This is because the input energy storage capaci-
tors are not completely discharged and the CONTROL
pin capacitance has not discharged below the internal
power-up reset voltage.
• Keep the SOURCE pin length very short. Use a Kelvin
connection to the SOURCE pin for the CONTROL pin by-
pass capacitor. Use single point grounding techniques
at the SOURCE pin as shown in Figure 9.
• In some cases, minimum loading may be necessary to
keep a lightly loaded or unloaded output voltage within
the desired range due to the minimum ON-time.
• Minimize peak voltage and ringing on the DRAIN volt-
age at turn-off. Use a Zener or TVS Zener diode to
clamp the drain voltage below the breakdown voltage
rating of TOPSwitch under all conditions, including start-
up and overload. The maximum recommended clamp
Zener voltage for the TOP2XX series is 200 V and the
corresponding maximum reflected output voltage on the
primary is 135 V. Please see Step 4: AN-16 in the 1996-
97 Data Book and Design Guide or on our Web site.
Replacing TOPSwitch with TOPSwitch-II
There is no external latching shutdown function in
TOPSwitch-II. Otherwise, the functionality of the TOPSwitch-II
devices is same as that of the TOPSwitch family. However,
before considering TOPSwitch-II as a 'drop in' replace-
ment in an existing TOPSwitch design, the design should
be verified as described below.
• The transformer should be designed such that the rate
of change of drain current due to transformer saturation
is within the absolute maximum specification (∆ID in
100 ns before turn off as shown in Figure 13). As a
guideline, for most common transformer cores, this can
be achieved by maintaining the Peak Flux Density (at
maximum ILIMIT current) below 4200 Gauss (420 mT).
The transformer spreadsheets Rev. 2.1 (or later) for con-
tinuous and Rev.1.0 (or later) for discontinuous conduc-
tion mode provide the necessary information.
The new TOPSwitch-II family offers more power capability
than the original TOPSwitch family for the same MOSFET
DS(ON). Therefore, the original TOPSwitch design must
be reviewed to make sure that the selected TOPSwitch-II
replacement device and other primary components are not
over stressed under abnormal conditions.
R
The following verification steps are recommended:
• Do not plug TOPSwitch into a “hot” IC socket dur-
ing test. External CONTROL pin capacitance may be
charged to excessive voltage and cause TOPSwitch
damage.
• Check the transformer design to make sure that it
meets the ∆ID specification as outlined in the General
Guidelines section above.
• While performing TOPSwitch device tests, do not
exceed maximum CONTROL pin voltage of 9 V or maxi-
mum CONTROL pin current of 100 mA.
• Thermal: Higher power capability of the TOPSwitch-II
would in many instances allow use of a smaller MOS-
FET device (higher RDS(ON)) for reduced cost. This may
affect TOPSwitch power dissipation and power supply
efficiency. Therefore thermal performance of the power
supply must be verified with the selected TOPSwitch-II
device.
• Under some conditions, externally provided bias or
supply current driven into the CONTROL pin can hold
the TOPSwitch in one of the 8 auto-restart cycles in-
definitely and prevent starting. To avoid this problem when
doing bench evaluations, it is recommended that the VC
power supply be turned on before the DRAIN voltage is
applied. TOPSwitch can also be reset by shorting the
CONTROL pin to the SOURCE pin momentarily.
• Clamp Voltage: Reflected and Clamp voltages should
be verified not to exceed recommended maximums
for the TOP2XX Series: 135 V Reflected/200 V Clamp.
Please see Step 4: AN-16 in the Data Book and Design
Guide and readme.txt file attached to the transformer
design spreadsheets.
• CONTROL pin currents during auto-restart operation
are much lower at low input voltages (< 36 V) which in-
creases the auto-restart cycle time (see the IC vs. DRAIN
Voltage Characteristic curve).
• Agency Approval: Migrating to TOPSwitch-II may
require agency re-approval.
8
Rev. G 08/16
www.power.com
TOP221-227
TO-220 PACKAGE
S
D
C
TOP VIEW
DIP-8/SMD-8 PACKAGE
SOURCE
SOURCE
CONTROL
DRAIN
TOP VIEW
Figure 9. Recommended TOPSwitch Layout.
Design Tools
All data sheets, application literature and up-to-date versions
of the Transformer Design Spreadsheets can be downloaded
from our Web site at www.power.com. A diskette of the
Transformer Design Spreadsheets may also be obtained by
sending in the completed form provided at the end of this
data sheet.
The following tools available from Power Integrations greatly
simplify TOPSwitch based power supply design.
• Data Book and Design Guide includes extensive
application information
• Excel Spreadsheets for Transformer Design - Use of
this tool is strongly recommended for all TOPSwitch
designs.
• Reference design boards – Production viable designs
that are assembled and tested.
9
Rev. G 08/16
www.power.com
TOP221-227
ABSOLUTE MAXIMUM RATINGS(1,5)
Notes:
DRAIN Voltage .................................................. -0.3 to 700 V
1. All voltages referenced to SOURCE, TA = 25 °C.
2. Related to transformer saturation – see Figure 13.
3. Normally limited by internal circuitry.
DRAIN Current Increase (∆ID) in 100 ns except during
blanking time ................................................. 0.1 x ILIMIT(MAX)
(2)
CONTROL Voltage............................................ - 0.3 V to 9 V
CONTROL Current.................................................... 100 mA
Storage Temperature ........................................-65 to 150 °C
Operating Junction Temperature(3) ...................-40 to 150 °C
Lead Temperature(4) ...................................................260 °C
4. 1/16" from case for 5 seconds.
5. The Absolute Maximum Ratings specified may be applied,
one at a time without causing permanent damage to the
product. Exposure to Absolute Maximum Ratings for ex-
tended periods of time may affect product reliability.
THERMAL RESISTANCE
Thermal Resistance: Y Package
Notes:
(θJA)(1) ............................................. 70 °C/W 1. Free standing with no heat sink.
(θJC)(2) ............................................... 2 °C/W 2. Measured at tab closest to plastic interface or SOURCE pin.
P/G Package:
3. Soldered to 0.36 sq. inch (232 mm2), 2 oz. (610 gm/m2) copper clad.
(θJA) ............................45 °C/W(3); 35 °C/W(4) 4. Soldered to 1 sq. inch (645 mm2), 2 oz. (610 gm/m2) copper clad.
(θJC)(2) ............................................. 11 °C/W
Conditions
(Unless Otherwise Specified)
Parameter
Symbol
Min
Typ
Max
Units
See Figure 14
SOURCE = 0 V; TJ = -40 to 125 °C
CONTROL FUNCTIONS
fOSC
Output Frequency
IC = 4 mA, TJ = 25 °C
IC = ICD1 + 0.4 mA, See Figure 10
IC = 10 mA, See Figure 10
90
64
100
67
110
70
kHz
%
DMAX
Maximum Duty Cycle
Minimum Duty Cycle
DMIN
0.7
-21
1.7
-16
2.7
-11
%
PWM
Gain
IC = 4 mA, TJ = 25 °C
%/mA
See Figure 4
PWM Gain
Temperature Drift
-0.05
2.0
See Note A
%/mA/°C
External Bias Current
Dynamic Impedance
IB
0.8
10
3.3
22
mA
See Figure 4
IC = 4 mA, TJ = 25 °C
15
Ω
ZC
See Figure 11
Dynamic Impedance
Temperature Drift
0.18
%/°C
SHUTDOWN/AUTO-RESTART
VC = 0 V
VC = 5 V
-2.4
-2
-1.9
-1.5
-1.2
-0.8
CONTROL Pin
IC
TJ = 25 °C
mA
Charging Current
Charging Current
Temperature Drift
See Note A
S1 open
0.4
VC(AR)
%/°C
10
Rev. G 08/16
www.power.com
TOP221-227
Conditions
(Unless Otherwise Specified)
See Figure 14
Parameter
Symbol
Min
Typ
Max
Units
SOURCE = 0 V; TJ = -40 to 125 °C
SHUTDOWN/AUTO-RESTART (cont.)
Auto-restart
Threshold Voltage
S1 open
S1 open
S1 open
5.7
4.7
1.0
V
V
UV Lockout
Threshold Voltage
4.4
0.6
5.0
Auto-restart
Hysteresis Voltage
V
TOP221-222
TOP223-227
2
2
5
5
9
8
Auto-restart
Duty Cycle
S1 open
%
Hz
Auto-restart
Frequency
S1 open
1.2
CIRCUIT PROTECTION
di/dt = 40 mA/µs,
TJ = 25 °C
TOP221YN
TOP221PN or GN
TOP222YN
0.23
0.45
0.25
0.50
0.28
0.55
di/dt = 80 mA/µs,
TJ = 25 °C
di/dt = 160 mA/µs,
TJ = 25 °C
TOP222PN or GN
TOP223YN
0.90
1.35
1.80
2.25
2.70
1.00
1.50
2.00
2.50
3.00
1.10
1.65
2.20
2.75
3.30
TOP223PN or GN
TOP224YN
Self-protection
ILIMIT
di/dt = 240 mA/µs,
TJ = 25 °C
A
Current Limit
TOP224PN or GN
di/dt = 320 mA/µs,
TJ = 25 °C
TOP225YN
TOP226YN
di/dt = 400 mA/µs,
TJ = 25 °C
di/dt = 480 mA/µs,
TOP227YN
TJ = 25 °C
0.75 x
ILIMIT(MIN)
≤ 85 VAC
(Rectified Line Input)
See Figure 12
IINIT
A
TJ = 25 °C
Initial Current Limit
0.6 x
ILIMIT(MIN)
265 VAC
(Rectified Line Input)
Leading Edge
tLEB
IC = 4 mA,
TJ = 25 °C
ns
180
Blanking Time
11
Rev. G 08/16
www.power.com
TOP221-227
Conditions
(Unless Otherwise Specified)
See Figure 14
Parameter
Symbol
Min
Typ
Max
Units
SOURCE = 0 V; TJ = -40 to 125 °C
CIRCUIT PROTECTION (cont.)
Current Limit
tILD
IC = 4 mA
ns
°C
V
100
135
3.3
Delay
Thermal Shutdown
Temperature
IC = 4 mA
S2 open
125
2.0
Power-up Reset
VC(RESET)
4.3
Threshold Voltage
OUTPUT
31.2
36.0
TOP221
TJ = 25 °C
ID = 25 mA
TJ = 100 °C
51.4
15.6
25.7
60.0
18.0
30.0
TOP222
ID = 50 mA
TOP223
TJ = 25 °C
TJ = 100 °C
TJ = 25 °C
TJ = 100 °C
7.8
12.9
5.2
9.0
15.0
6.0
ID = 100 mA
TOP224
TJ = 25 °C
Ω
ON-State
RDS(ON)
Resistance
ID = 150 mA
TJ = 100 °C
8.6
10.0
TOP225
ID = 200 mA
TOP226
TJ = 25 °C
TJ = 100 °C
TJ = 25 °C
3.9
6.4
3.1
5.2
2.6
4.3
4.5
7.5
3.6
6.0
3.0
5.0
ID = 250 mA
TOP227
TJ = 100 °C
TJ = 25 °C
TJ = 100 °C
ID = 300 mA
See Note B
VDS = 560 V, TA = 125 °C
OFF-State
Current
250
µA
IDSS
See Note B
ID = 100 µA, TA = 25 °C
Breakdown
Voltage
700
V
BVDSS
Rise
Time
100
50
ns
ns
tR
Measured in a Typical Flyback
Converter Application.
Fall
Time
tF
12
Rev. G 08/16
www.power.com
TOP221-227
Conditions
(Unless Otherwise Specified)
See Figure 14
Parameter
Symbol
Min
Typ Max
Units
SOURCE = 0 V; TJ = -40 to 125 °C
OUTPUT (cont.)
V
V
See Note C
IC = 4 mA
36
DRAIN Supply Voltage
Shunt Regulator
Voltage
VC(SHUNT)
5.5
5.7
50
6.0
Shunt Regulator
Temperature Drift
ppm/°C
Output
TOP221-224
TOP225-227
0.6
0.7
1.2
1.4
1.6
1.8
ICD1
CONTROL Supply/
Discharge Current
MOSFET Enabled
mA
ICD2
0.5
0.8
1.1
Output MOSFET Disabled
NOTES:
A. For specifications with negative values, a negative temperature coefficient corresponds to an increase in
magnitude with increasing temperature, and a positive temperature coefficient corresponds to a decrease in
magnitude with increasing temperature.
B. The breakdown voltage and leakage current measurements can be accomplished as shown in Figure 15 by
using the following sequence:
i. The curve tracer should initially be set at 0 V. The base output should be adjusted through a voltage
sequence of 0 V, 6.5 V, 4.3 V, and 6.5 V, as shown. The base current from the curve tracer should not
exceed 100 mA. This CONTROL pin sequence interrupts the Auto-restart sequence and locks the
TOPSwitch internal MOSFET in th OFF-state.
ii. The breakdown and the leakage measurements can now be taken with the curve tracer. The maximum
voltage from the curve tracer must be limited to 700 V under all conditions.
C. It is possible to start up and operate TOPSwitch at DRAIN voltages well below 36 V. However, the CONTROL
pin charging current is reduced, which affects start-up time, auto-restart frequency, and auto-restart duty cycle.
Refer to the characteristic graph on CONTROL pin charge current (IC) vs. DRAIN voltage for low voltage opera-
tion characteristics.
13
Rev. G 08/16
www.power.com
TOP221-227
120
100
80
60
ꢀ0
20
0
t
ꢄ
t
ꢅ
HV
90%
90%
t
t
ꢀRAIN
ꢁꢂLTAꢃE
1
2
D =
1
Dynamic
ꢃ
10%
Impedance Slope
0 V
PI-2039-033001
0
2
ꢀ
6
8
10
Figure 10. TOPSwitch Duty Cycle Measurement.
CONTROL Pin Voltage (V)
Figure 11. TOPSwitch CONTROL Pin I-V Characteristic.
t
(ꢅlanking Time)
LEꢅ
1.3
1.2
1.1
1.0
0.ꢀ
0.8
0.ꢃ
0.6
0.ꢂ
0.ꢁ
0.3
0.2
0.1
100 ꢇꢈ
ꢉꢊꢋꢌ
∆ꢁꢆ
IINIT(MIN) @ 85 VAC
IINIT(MIN) @ 265 VAC
DRAIN
CURRENT
ILIMIT(MAꢄ) @ 25 ˚C
ILIMIT(MIN) @ 25 ˚C
0 ꢍ
0
0
1
2
3
ꢁ
ꢂ
6
ꢃ
8
ꢀꢁꢂꢃ0ꢄ1ꢂ0ꢅ0ꢅ01
Time (µs)
Figure 13. Example of ∆ID on Drain Current Waveform with
Figure 12. Self-protection Current Limit Envelope.
Saturated Transformer.
14
Rev. G 08/16
www.power.com
TOP221-227
ꢄꢆ0 Ω
ꢇ ꢉ
ꢊꢋ
ꢄ
ꢂ
ꢅOꢀTꢆOꢇ
ꢄꢆ0 Ω
ꢅ
TOPꢂꢈꢉꢊꢋꢌ
ꢊ1
ꢄ0 ꢈ
0.1 µꢅ
ꢄꢆ µꢅ
0ꢂꢇ0 ꢈ
ꢀOTꢁꢂꢃ 1. ꢌꢍꢎꢏ ꢐeꢏꢐ ꢑꢎꢒꢑꢓꢎꢐ ꢎꢏ ꢔꢕꢐ ꢖꢗꢗꢘꢎꢑꢖꢙꢘe ꢚꢕꢒ ꢑꢓꢒꢒeꢔꢐ ꢘꢎꢛꢎꢐ ꢕꢒ ꢕꢓꢐꢗꢓꢐ ꢑꢍꢖꢒꢖꢑꢐeꢒꢎꢏꢐꢎꢑ ꢛeꢖꢏꢓꢒeꢛeꢔꢐꢏ.
ꢋ. ꢅꢕꢒ ꢀ ꢗꢖꢑꢜꢖꢝeꢞ ꢏꢍꢕꢒꢐ ꢖꢘꢘ ꢊꢟꢠRꢡꢢ ꢖꢔꢣ ꢊꢟꢠRꢡꢢ ꢤꢥꢈ Rꢌꢦꢧ ꢗꢎꢔꢏ ꢐꢕꢝeꢐꢍeꢒ.
ꢀꢁꢂ1ꢃ6ꢄꢂ1106ꢃ6
Figure 14. TOPSwitch General Test Circuit.
ꢆꢇꢈve
ꢉꢈꢊꢋeꢈ
ꢆ
ꢠ
ꢟ
ꢃ
ꢄ
ꢅOꢀTꢆOꢇ
ꢅ
TOPꢄꢈꢉꢊꢋꢌ
6.ꢡ ꢢ
ꢅ.ꢣ ꢢ
ꢀOTꢁꢂ ꢉꢌꢍꢎ ꢆꢏꢐꢉRꢏꢑ ꢒꢍꢓ ꢎeꢔꢇeꢓꢋe ꢍꢓꢕeꢈꢈꢇꢒꢕꢎ ꢕꢌe ꢖꢇꢕꢗꢂꢈeꢎꢕꢊꢈꢕ ꢎeꢔꢇeꢓꢋe ꢊꢓꢘ
ꢙꢗꢋꢚꢎ ꢕꢌe ꢉꢏꢀꢛꢜꢍꢕꢋꢌ ꢍꢓꢕeꢈꢓꢊꢙ ꢝꢏꢛꢞꢟꢉ ꢍꢓ ꢕꢌe ꢏꢞꢞꢂꢛꢕꢊꢕe.
ꢀꢁꢂꢃ10ꢄꢂ0ꢅ0ꢅ01
Figure 15. Breakdown Voltage and Leakage Current Measurement Test Circuit.
15
Rev. G 08/16
www.power.com
TOP221-227
BENCH TEST PRECAUTIONS FOR EVALUATION OF ELECTRICAL CHARACTERISTICS
The following precautions should be followed when testing
TOPSwitch by itself outside of a power supply. The sche-
matic shown in Figure 14 is suggested for laboratory testing
of TOPSwitch.
in this Auto-restart mode, there is only a 12.5% chance that
the control pin oscillation will be in the correct state (DRAIN
active state) so that the continuous DRAIN voltage waveform
may be observed. It is recommended that the VC power sup-
ply be turned on first and the DRAIN power supply second
if continuous drain voltage waveforms are to be observed.
The 12.5% chance of being in the correct state is due to the
8:1 counter. Temporarily shorting the CONTROL pin to the
SOURCE pin will reset TOPSwitch, which then will come up
in the correct state.
When the DRAIN supply is turned on, the part will be in the
Auto-restart mode. The CONTROL pin voltage will be oscil-
lating at a low frequency from 4.7 to 5.7 V and the DRAIN is
turned on every eighth cycle of the CONTROL pin oscilla-
tion. If the CONTROL pin power supply is turned on while
Typical Performance Characteristics
FREQUENCY vs. TEMPERATURE
BREAKDOWN vs. TEMPERATURE
Junction Temperature (°C)
Junction Temperature (°C)
CURRENT LIMIT vs. TEMPERATURE
ꢃ ꢖꢗꢘ ꢀꢁꢂꢃꢄ ꢅOꢏTꢂꢙꢚ
ꢎ
ꢀ
ꢂ
ꢄ ꢅ ꢂ
ꢃ
1.6
1.ꢀ
0.8
0.ꢁ
0
0
ꢀ0
ꢁ0
60
80
100
Junction Temperature (°C)
ꢀꢁꢂꢃꢄ ꢅꢆꢇꢈꢉꢊꢋ ꢌꢅꢍ
16
Rev. G 08/16
www.power.com
TOP221-227
Typical Performance Characteristics (cont.)
OUTPUT CHARACTERISTICS
C
OSS
vs. DRAIN VOLTAGE
°
°
DRAIN Voltage (V)
DRAIN Voltage (V)
DRAIN CAPACITANCE POWER
DRAIN Voltage (V)
17
Rev. G 08/16
www.power.com
TOP221-227
Plastic TO-220/3
J
mm
DIM
inches
B
K
P
11.68-12.19
10.16-10.54
5.99-6.60
6.10 - REF.
13.21-14.22
.71-.97
A
B
C
D
E
F
.460-.480
.400-.415
.236-.260
.240 - REF.
.520-.560
.028-.038
.045-.055
.090-.110
.165-.185
.045-.055
.095-.115
.015-.020
.705-.715
.146-.156
.103-.113
Notes:
C
1. Package dimensions conform
to JEDEC specification TO-220
AB for standard flange
mounted, peripheral lead
package; .100 inch lead
spacing (Plastic) 3 leads (issue
J, March 1987).
O
A
N
2. Controlling dimensions are
inches.
1.14-1.40
2.29-2.79
4.19-4.70
1.14-1.40
2.41-2.92
.38-.51
G
H
J
3. Pin numbers start with Pin 1,
and continue from left to right
when viewed from the top.
4. Dimensions shown do not
include mold flash or other
protrusions. Mold flash or
protrusions shall not exceed
.006 (.15 mm) on any side.
5. Position of terminals to be
measured at a position .25
(6.35 mm) from the body.
6. All terminals are solder plated.
7. Bent lead should be 12 mil
max.
L
D
K
L
E
M
N
O
P
17.91-18.16
3.71-3.96
2.62-2.87
F
M
H
G
Y03A
PI-1848-050602
PDIP-8 (P Package)
D S .004 (.10)
DIM
Inches
mm
8
5
-E-
A
B
C
G
H
J1
J2
K
L
M
N
P
Q
0.356-0.387
0.240-0.260
0.125-0.145
0.015-0.040
0.118-0.140
0.057-0.068
0.014-0.022
0.008-0.015
0.100 BSC
0.030 (MIN)
0.300-0.320
0.300-0.390
0.300 BSC
9.05-9.83
6.10-6.60
3.18-3.68
0.38-1.02
3.00-3.56
1.45-1.73
0.36-0.56
0.20-0.38
2.54 BSC
0.76 (MIN)
7.62-8.13
7.62-9.91
7.62 BSC
B
1
4
A
-D-
-F-
M
J1
N
Notes:
1. Package dimensions conform to JEDEC
C
specification MS-001-AB for standard dual in-line
(DIP) package .300 inch row spacing (PLASTIC)
8 leads (issue B, 7/85).
2. Controlling dimensions are inches.
3. Dimensions shown do not include mold flash
or other protrusions. Mold flash or protrusions
shall not exceed .006 (.15) on any side.
4. D, E and F are reference datums on the molded
body.
H
K
G
Q
J2
P08A
L
P
PI-2076-081716
18
Rev. G 08/16
www.power.com
TOP221-227
SMD-8 (G Package)
D S .004 (.10)
DIM
Inches
mm
8
5
-E-
A
B
C
G
H
J1
J2
J3
J4
K
L
M
P
0.356-0.387
0.240-0.260
0.125-0.145
0.004-0.012
0.036-0.044
0.057-0.068
0.048-0.053
0.032-0.037
0.007-0.011
0.010-0.012
0.100 BSC
0.030 (MIN)
0.372-0.388
0-8°
9.05-9.83
6.10-6.60
3.18-3.68
0.10-0.30
0.91-1.12
1.45-1.73
1.22-1.35
0.81-0.94
0.18-0.28
0.25-0.30
2.54 BSC
0.76 (MIN)
9.45-9.86
0-8°
.420
P
B
.046
.060 .046
.060
.080
Pin 1
1
4
L
.086
.186
.286
α
A
-D-
-F-
Solder Pad Dimensions
M
J1
Notes:
1. Package dimensions conform to JEDEC
specification MS-001-AB (issue B, 7/85)
except for lead shape and size.
2. Controlling dimensions are inches.
3. Dimensions shown do not include mold
flash or other protrusions. Mold flash or
protrusions shall not exceed .006 (.15) on
any side.
C
K
.004 (.10)
H
J3
J4
.010 (.25) M A S
α
G
4. D, E and F are reference datums on the
molded body.
G08A
J2
PI-2077-081716
Part Ordering Information
• TOPSwitch Product Family
• II Series Number
• Package Identifier
G
P
Y
Plastic SMD-8
Plastic DIP-8
Plastic TO-220/3
• Lead Finish
N
Lead Free
• Tape & Reel and Other Options
Blank
TL
Standard Configurations
Tape & Reel, 1000 pcs minimum, G Package only
TOP 222
G N TL
19
Rev. G 08/16
www.power.com
TOP221-227
Revision Notes
Date
C
-
12/97
Updated package references, corrected spelling, storage temperature and 0JC and updated nomenclature in param-
eter table. Added G package references to Self-Protection Current Limit parameter. Corrected font sizes in figures.
D
07/01
E
F
Updated with new Brand Style.
07/15
10/15
08/16
Updated part numbers with the "N" suffix. Added Y, P and G package drawings.
Updated PDIP-8 (P Package) and SMD-8 (G Package) per PCN-16232.
G
For the latest updates, visit our website: www.power.com
Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations
does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES NO WARRANTY
HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
Patent Information
The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered by one
or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of
Power Integrations patents may be found at www.power.com. Power Integrations grants its customers a license under certain patent rights as set
forth at http://www.power.com/ip.htm.
Life Support Policy
POWER INTEGRATIONS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein:
1. A Life support device or system is one which, (i) is intended for surgical implant into the body, or (ii) supports or sustains life, and (iii)
whose failure to perform, when properly used in accordance with instructions for use, can be reasonably expected to result in significant injury
or death to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or system, or to affect its safety or effectiveness.
The PI logo, TOPSwitch, TinySwitch, SENZero, SCALE-iDriver, Qspeed, PeakSwitch, LYTSwitch, LinkZero, LinkSwitch, InnoSwitch, HiperTFS,
HiperPFS, HiperLCS, DPA-Switch, CAPZero, Clampless, EcoSmart, E-Shield, Filterfuse, FluxLink, StakFET, PI Expert and PI FACTS are trademarks of
Power Integrations, Inc. Other trademarks are property of their respective companies. ©2016, Power Integrations, Inc.
Power Integrations Worldwide Sales Support Locations
World Headquarters
5245 Hellyer Avenue
San Jose, CA 95138, USA.
Main: +1-408-414-9200
Customer Service:
Phone: +1-408-414-9665
Fax: +1-408-414-9765
e-mail: usasales@power.com
Germany
Lindwurmstrasse 114
80337 Munich
Japan
Kosei Dai-3 Bldg.
2-12-11, Shin-Yokohama,
Kohoku-ku
Yokohama-shi Kanagawa
222-0033 Japan
Phone: +81-45-471-1021
Fax: +81-45-471-3717
e-mail: japansales@power.com
Taiwan
5F, No. 318, Nei Hu Rd., Sec. 1
Nei Hu Dist.
Taipei 11493, Taiwan R.O.C.
Phone: +886-2-2659-4570
Fax: +886-2-2659-4550
e-mail: taiwansales@power.com
Germany
Phone: +49-895-527-39110
Fax: +49-895-527-39200
e-mail: eurosales@power.com
India
UK
China (Shanghai)
Rm 1601/1610, Tower 1,
Kerry Everbright City
No. 218 Tianmu Road West,
Shanghai, P.R.C. 200070
Phone: +86-21-6354-6323
Fax: +86-21-6354-6325
e-mail: chinasales@power.com
#1, 14th Main Road
Vasanthanagar
Bangalore-560052 India
Phone: +91-80-4113-8020
Fax: +91-80-4113-8023
e-mail: indiasales@power.com
Cambridge Semiconductor,
a Power Integrations company
Westbrook Centre, Block 5, 2nd Floor
Korea
RM 602, 6FL
Korea City Air Terminal B/D, 159-6 Milton Road
Samsung-Dong, Kangnam-Gu,
Seoul, 135-728, Korea
Phone: +82-2-2016-6610
Fax: +82-2-2016-6630
Cambridge CB4 1YG
Phone: +44 (0) 1223-446483
e-mail: eurosales@power.com
Italy
Via Milanese 20, 3rd. Fl.
20099 Sesto San Giovanni
(MI) Italy
e-mail: koreasales@power.com
China (Shenzhen)
17/F, Hivac Building, No. 2,
Keji Nan 8th Road, Nanshan
Singapore
51 Newton Road
Phone: +39-024-550-8701
District, Shenzhen, China, 518057 Fax: +39-028-928-6009
#19-01/05 Goldhill Plaza
Singapore, 308900
Phone: +65-6358-2160
Fax: +65-6358-2015
e-mail: singaporesales@power.com
Phone: +86-755-8672-8689
Fax: +86-755-8672-8690
e-mail: eurosales@power.com
e-mail: chinasales@power.com
20
Rev. G 08/16
www.power.com
相关型号:
©2020 ICPDF网 联系我们和版权申明