83503-21 [PSEMI]
3.5 GHz Low Power UltraCMOS Divide-by-8 Prescaler Military Operating Temperature Range; 3.5 GHz的低功耗的UltraCMOS分频预分频器的8军用工作温度范围
| 型号： | 83503-21 |
| 厂家： | 
Peregrine Semiconductor |
| 描述： | 3.5 GHz Low Power UltraCMOS Divide-by-8 Prescaler Military Operating Temperature Range |
| 文件： | 总8页 (文件大小：186K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Product Specification
PE83503
3.5 GHz Low Power UltraCMOS™
Divide-by-8 Prescaler
Product Description
Military Operating Temperature Range
The PE83503 is a high-performance monolithic UltraCMOS™
prescaler with a fixed divide ratio of 8. Its operating frequency
range is 1.5 GHz to 3.5 GHz. The PE83503 operates on a
nominal 3 V supply and draws only 12 mA. It is packaged in a
small 8-lead MSOP and is ideal for microwave PLL synthesis
solutions.
Features
• High-frequency operation:
1.5 GHz to 3.5 GHz
• Fixed divide ratio of 8
The PE83503 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance
of GaAs with the economy and integration of conventional
CMOS.
• Low-power operation: 12 mA typical
@ 3 V across frequency
• Small package: 8-lead MSOP
• Low Cost
Figure 2. Package Type
Figure 1. Functional Schematic Diagram
8-lead MSOP
D
Q
D
Q
D
Q
IN
OUT
CLK QB
CLK QB
CLK QB
Output
Buffer
Pre-Amp
Table 1. Electrical Specifications (ZS = ZL = 50 Ω)
2.85 V ≤ VDD ≤ 3.15 V; -55° C ≤ TA ≤ 125° C, unless otherwise specified
Parameter
Supply Voltage
Conditions
Minimum
Typical
Maximum
Units
V
2.85
3.0
13
3.15
19
Supply Current
mA
Input Frequency (FIN)
1.5
-5
3.5
GHz
Input Power (PIN)
1500 MHz ≤ Fin ≤ 2800 MHz
2800 MHz < Fin ≤ 3500 MHz
+10
+10
dBm
0
0
dBm
dBm
Output Power
Document No. 70-0126-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 8
PE83503
Product Specification
Figure 3. Pin Configuration (Top View)
Electrostatic Discharge (ESD) Precautions
When handling this UltraCMOS™ device, observe
the same precautions that you would use with
other ESD-sensitive devices. Although this device
contains circuitry to protect it from damage due to
ESD, precautions should be taken to avoid
exceeding the rating specified in Table 3.
1
2
3
4
8
7
6
5
VDD
GND
OUT
GND
GND
IN
PE83503
DEC
GND
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS™
devices are immune to latch-up.
Table 2. Pin Descriptions
Device Functional Considerations
Pin
No.
Pin
Name
Description
The PE83503 takes an input signal frequency
from 1.5 GHz to 3.5 GHz and produces an output
signal frequency one-eighth that of the supplied
input. In order for the prescaler to work properly,
several conditions need to be adhered to. It is
crucial that pin 3 be supplied with a bypass
capacitor to ground. In addition, the input and
output signals (pins 2 & 7, respectively) need to
be AC coupled via an external capacitor as shown
in the test circuit in Figure 7.
1
VDD
Power supply pin. Bypassing is required.
Input signal pin. Should be coupled with a
capacitor (eg 15pF)
2
IN
Power supply decoupling pin. Place a
capacitor as close as possible and connect
directly to the ground plane (eg 10 nF and
10 pF).
3
4
DEC
GND
Ground pin. Ground pattern on the board
should be as wide as possible to reduce
ground impedance.
5
6
GND
GND
Ground pin.
Ground pin.
The ground pattern on the board should be made
as wide as possible to minimize ground
impedance.
Divided frequency output pin. This pin
should be coupled with a capacitor (eg 100
pF).
7
8
OUT
GND
Ground pin.
Table 3. Absolute Maximum Ratings
Symbol
Parameter/Conditions Min Max Units
VDD
Supply voltage
4.0
V
Storage temperature
range
TST
TOP
-65
-55
150
°C
Operating temperature
range
125
°C
ESD voltage (Human
Body Model)
VESD
250
15
V
PINMAX
Maximum input power
dBm
Absolute Maximum Ratings are those values
listed in the above table. Exceeding these values
may cause permanent device damage. Exposure
to absolute maximum ratings for extended periods
may affect device reliability.
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0126-02 │ UltraCMOS™ RFIC Solutions
Page 2 of 8
PE83503
Product Specification
Figure 4. Test Circuit Block Diagram
VDD
+
-
3 V +/- 0.15 V
10 pF
1000 pF
15 pF
1
2
3
4
8
7
6
5
50 Ω
100 pF
50 Ω
PE83503
Spectrum
Analyzer
Signal Generator
10 nF
10 pF
Figure 5. High Frequency System Application
The wideband frequency of operation of the PE83503 makes it an ideal part for use in a
DBS downconverter system.
BASEBAND
OUTPUT
FM
DEMOD
INPUT FROM
DBS 1ST IF
BPF
SAW
AGC
DIVIDE-BY-8
PE3291
PE83503
Low Noise
PLL SYNTH
LPF
Document No. 70-0126-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 3 of 8
PE83503
Product Specification
Typical Performance Data: VDD = 3.0 V
Figure 6. Input Sensitivity
Figure 7. Device Current
Figure 8. Output Power
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0126-02 │ UltraCMOS™ RFIC Solutions
Page 4 of 8
PE83503
Product Specification
It is the responsibility of the customer to determine
proper supply decoupling for their design application.
Evaluation Kit
Evaluation Kit Operation
The DEC pin (3) must be connected to a low
impedance AC ground for proper device operation. On
the board, two decoupling capacitors (C6 = 10 nF, C4 =
10 pF), located on the back of the board, perform this
function.
The MSOP Prescaler Evaluation Board was designed
to help customers evaluate the PE83503 Divide-by-8
Prescaler. On this board, the device input (pin 2) is
connected to connector J1 through a 50 ꢀ transmission
line. A series capacitor (C3) provides the necessary
DC block for the device input. It is important to note
that the value of this capacitance will impact the
performance of the device. A value of 15pF was found
to be optimal for this board layout; other applications
may require a different value.
Applications Support
If you have a problem with your evaluation kit or if you
have applications questions call (858) 731-9400 and
ask for applications support. You may also contact us
by fax or e-mail:
Fax: (858) 731-9499
E-Mail: help@psemi.com
The device output (pin 7) is connected to connector J3
through a 50 ꢀ transmission line. A series capacitor
(C1) provides the necessary DC block for the device
output. Note that this capacitor must be chosen to
have a low impedance at the desired output frequency
the device. The value of 100pF was chosen to provide
a wide operating range for the evaluation board.
Figure 9. Evaluation Board Layouts
Peregrine Specification 101/0035
The board is constructed of a two-layer FR4 material
with a total thickness of 0.031”. The bottom layer
provides ground for the RF transmission lines. The
transmission lines were designed using a coplanar
waveguide above ground plane model with trace width
of 0.030”, trace gaps of 0.007”, dielectric thickness of
0.028”, metal thickness of 0.0014” and εr of 4.4. Note
that the predominate mode for these transmission lines
is coplanar waveguide.
J2 provides DC power to the device. Starting from the
lower left pin, the second pin to the right (J2-3) is
connected to the device VDD pin (1). Two decoupling
capacitors (10 pF, 1000 pF) are included on this trace.
Figure 10. Evaluation Board Schematic
Peregrine Specification 102/0200
Document No. 70-0126-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 5 of 8
PE83503
Product Specification
Figure 11. Package Drawing
8-lead MSOP
TOP VIEW
0.65BSC
.525BSC
8
7
6
5
2.45±0.10
2X
3.00±0.10
0.51±0.13
0.51±0.13
- B -
2
3
4
1
.25 A B C
- C -
2.95±0.10
0.86±0.08
2.95±0.10
1.10 MAX
- A -
+0.07
-0.08
3.00±0.10
4.90±0.15
0.10 A
0.33
0.08
0.10±0.05
A B C
3.00±0.10
FRONT VIEW
SIDE VIEW
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0126-02 │ UltraCMOS™ RFIC Solutions
Page 6 of 8
PE83503
Product Specification
Figure 12. Tape and Reel Specifications
8-lead MSOP
Pin1
Table 4. Ordering Information
Order Code
83503-21
Part Marking
83503
Description
Package
Shipping Method
50 pcs. / Tube
2000 pcs. / T&R
1 / Box
PE83503-08MSOP-100A
8-lead MSOP
83503-22
83503
PE83503-08MSOP-2000C
PE83503-08MSOP-EK
8-lead MSOP
83503-00
PE83503-EK
Evaluation Board
Document No. 70-0126-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 7 of 8
PE83503
Product Specification
Sales Offices
The Americas
North Asia Pacific
Peregrine Semiconductor Corporation
Peregrine Semiconductor K.K.
9450 Carroll Park Drive
San Diego, CA 92121
Tel: 858-731-9400
Teikoku Hotel Tower 10B-6
1-1-1 Uchisaiwai-cho, Chiyoda-ku
Tokyo 100-0011 Japan
Fax: 858-731-9499
Tel: +81-3-3502-5211
Fax: +81-3-3502-5213
Europe
Peregrine Semiconductor, Korea
#B-2402, Kolon Tripolis, #210
Geumgok-dong, Bundang-gu, Seongnam-si
Gyeonggi-do, 463-480 S. Korea
Tel: +82-31-728-4300
Peregrine Semiconductor Europe
Bâtiment Maine
13-15 rue des Quatre Vents
F-92380 Garches, France
Tel: +33-1-4741-9173
Fax : +33-1-4741-9173
Fax: +82-31-728-4305
South Asia Pacific
Space and Defense Products
Americas:
Peregrine Semiconductor, China
Shanghai, 200040, P.R. China
Tel: +86-21-5836-8276
Tel: 858-731-9453
Fax: +86-21-5836-7652
Europe, Asia Pacific:
180 Rue Jean de Guiramand
13852 Aix-En-Provence Cedex 3, France
Tel: +33-4-4239-3361
Fax: +33-4-4239-7227
For a list of representatives in your area, please refer to our Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The information in this data sheet is believed to be reliable.
However, Peregrine assumes no liability for the use of this
information. Use shall be entirely at the user’s own risk.
The product is in a formative or design stage. The data
sheet contains design target specifications for product
development. Specifications and features may change in
any manner without notice.
No patent rights or licenses to any circuits described in this
data sheet are implied or granted to any third party.
Preliminary Specification
Peregrine’s products are not designed or intended for use in
devices or systems intended for surgical implant, or in other
applications intended to support or sustain life, or in any
application in which the failure of the Peregrine product could
create a situation in which personal injury or death might occur.
Peregrine assumes no liability for damages, including
consequential or incidental damages, arising out of the use of
its products in such applications.
The data sheet contains preliminary data. Additional data
may be added at a later date. Peregrine reserves the right
to change specifications at any time without notice in order
to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine
decides to change the specifications, Peregrine will notify
customers of the intended changes by issuing a DCN
(Document Change Notice).
The Peregrine name, logo, and UTSi are registered trademarks
and UltraCMOS and HaRP are trademarks of Peregrine
Semiconductor Corp.
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0126-02 │ UltraCMOS™ RFIC Solutions
Page 8 of 8
相关型号：
83503-22
3.5 GHz Low Power UltraCMOS Divide-by-8 Prescaler Military Operating Temperature Range
PSEMI
©2020 ICPDF网 联系我们和版权申明