PE83501_06 [PSEMI]
3.5 GHz Low Power UltraCMOS Divide-by-2 Prescaler Military Operating Temperature Range; 3.5 GHz的低功耗的UltraCMOS分频预分频器军事工作温度范围型号: | PE83501_06 |
厂家: | Peregrine Semiconductor |
描述: | 3.5 GHz Low Power UltraCMOS Divide-by-2 Prescaler Military Operating Temperature Range |
文件: | 总8页 (文件大小:197K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Product Specification
PE83501
3.5 GHz Low Power UltraCMOS™
Divide-by-2 Prescaler
Product Description
Military Operating Temperature Range
The PE83501 is a high-performance dynamic UltraCMOS™
prescaler with a fixed divide ratio of 2. Its operating frequency
range is 400 MHz to 3.5 GHz. The PE83501 operates on a
nominal 3 V supply and draws only 12 mA. It is packaged in a
small 8-lead MSOP and is ideal for frequency scaling and
microwave PLL synthesis solutions.
Features
• High-frequency operation:
400 MHz to 3.5 GHz
• Fixed divide ratio of 2
The PE83501 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance
of GaAs with the economy and integration of conventional
CMOS.
• Low-power operation:
12 mA typical @ 3 V
• Small package: 8-lead MSOP
• Low cost
Figure 2. Package Type
Figure 1. Functional Schematic Diagram
8-lead MSOP
Fout
D
Q
Fin
CLK
DEC
DRIVER
OUTPUT BUFFER
QB
PREAMP
OFF-CHIP
BYPASS
Table 1. Electrical Specifications (ZS = ZL = 50 Ω)
2.85V ≤ VDD ≤ 3.15 V; -55° C ≤ TA ≤ 125° C, unless otherwise specified
Parameter
Conditions
Minimum
Typical
Maximum
3.15
Units
V
Supply Voltage
2.85
3.0
13
Supply Current
18
mA
Input Frequency (Fin)
Input Power (Pin)
400
3500
MHz
400 MHz ≤ Fin ≤ 2.0 GHz
2.0 GHz < Fin ≤ 2.8 GHz
2.8 GHz < Fin ≤ 3.5 GHz
400 MHz ≤ Fin ≤ 3.5 GHz
-10
0
+10
+10
+10
dBm
dBm
dBm
dBm
+5
-15
Output Power (Pout)
Document No. 70-0124-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 8
PE83501
Product Specification
Figure 3. Pin Configuration (Top View)
Electrostatic Discharge (ESD) Precautions
When handling this UltraCMOS™ device, observe
the same precautions that you would use with
other ESD-sensitive devices. Although this device
contains circuitry to protect it from damage due to
ESD, precautions should be taken to avoid
exceeding the rating specified in Table 3.
1
2
3
4
8
7
6
5
VDD
GND
Fout
Fin
PE83501
DEC
GND
GND
GND
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS™
devices are immune to latch-up.
Table 2. Pin Descriptions
Device Functional Considerations
Pin
No.
Pin
Name
Description
The PE83501 divides a 400 MHz to 3.5 GHz input
signal by two, producing a 200 MHz to 1.75 GHz
output signal. To work properly, pin 3 must be
supplied with a bypass capacitor to ground. In
addition, the input and output signals (pins 2 & 7)
must be AC coupled via an external capacitor, as
shown in the test circuit in Figure 4.
1
VDD
Power supply pin. Bypassing is required.
Input signal pin. DC blocking capacitor
required (15 pF typical)
2
Fin
Power supply decoupling pin. Place a
capacitor as close as possible and connect
directly to the ground plane.
3
4
DEC
GND
Ground pin. Ground pattern on the board
should be as wide as possible to reduce
ground impedance.
The ground pattern on the board should be made
as wide as possible to minimize ground
impedance. See Figure 9 for a layout example.
5
6
GND
GND
Ground pin.
Ground pin.
Divided frequency output pin. DC blocking
capacitor required (47 pF typical)
7
8
Fout
GND
Ground pin.
Table 3. Absolute Maximum Ratings
Symbol
Parameter/Conditions Min Max Units
VDD
Pin
Supply voltage
Input Power
4.0
15
V
dBm
Storage temperature
range
TST
TOP
-65
-55
150
125
°C
°C
Operating temperature
range
ESD voltage (Human
Body Model)
VESD
250
V
Absolute Maximum Ratings are those values
listed in the above table. Exceeding these values
may cause permanent device damage. Exposure
to absolute maximum ratings for extended periods
may affect device reliability.
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0124-02 │ UltraCMOS™ RFIC Solutions
Page 2 of 8
PE83501
Product Specification
Figure 4. Test Circuit Block Diagram
VDD
3 V +/- 0.15 V
10 pF 1000 pF
1
2
3
4
8
7
6
5
50 Ω
50 Ω
15 pF
47 pF
PE83501
Spectrum
Analyzer
N/C
8 Lead
MSOP
Signal Generator
10 nF
10 pF
Figure 5. High Frequency System Application
The wideband frequency of operation of the PE83501 makes it an ideal part for use in a
DBS downconverter system.
FM
DEMOD
BASEBAND
OUTPUT
INPUT FROM
DBS 1ST IF
BPF
SAW
AGC
DIVIDE-BY-2
PE3236
LOW NOISE
PLL SYNTH
PE83501
LPF
Document No. 70-0124-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 3 of 8
PE83501
Product Specification
Typical Performance Data: VDD = 3.0 V
Figure 6. Input Sensitivity
Figure 7. Device Current
Figure 8. Output Power
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0124-02 │ UltraCMOS™ RFIC Solutions
Page 4 of 8
PE83501
Product Specification
It is the responsibility of the customer to determine
proper supply decoupling for their design application.
Evaluation Kit
Evaluation Kit Operation
The DEC pin (3) must be connected to a low
impedance AC ground for proper device operation. On
the board, two decoupling capacitors (C6 = 10 nF, C4 =
10 pF), located on the back of the board, perform this
function.
The MSOP Prescaler Evaluation Board was designed
to help customers evaluate the PE83501 Divide-by-2
Prescaler. On this board, the device input (pin 2) is
connected to connector J1 through a 50 ꢀ transmission
line. A series capacitor (C3) provides the necessary
DC block for the device input. It is important to note
that the value of this capacitance will impact the
performance of the device. A value of 15 pF was found
to be optimal for this board layout; other applications
may require a different value.
Applications Support
If you have a problem with your evaluation kit or if you
have applications questions call (858) 731-9400 and
ask for applications support. You may also contact us
by fax or e-mail:
Fax: (858) 731-9499
E-Mail: help@psemi.com
The device output (pin 7) is connected to connector J3
through a 50 ꢀ transmission line. A series capacitor
(C1) provides the necessary DC block for the device
output. Note that this capacitor must be chosen to
have a low impedance at the desired output frequency
the device. The value of 47 pF was chosen to provide
a wide operating range for the evaluation board.
Figure 9. Evaluation Board Layouts
Peregrine Specification 101/0035
The board is constructed of a two-layer FR4 material
with a total thickness of 0.031”. The bottom layer
provides ground for the RF transmission lines. The
transmission lines were designed using a coplanar
waveguide above ground plane model with trace width
of 0.030”, trace gaps of 0.007”, dielectric thickness of
0.028”, metal thickness of 0.0014” and εr of 4.4. Note
that the predominate mode for these transmission lines
is coplanar waveguide.
J2 provides DC power to the device. Starting from the
lower left pin, the second pin to the right (J2-3) is
connected to the device VDD pin (1). Two decoupling
capacitors (10 pF, 1000 pF) are included on this trace.
Figure 10. Evaluation Board Schematic
Peregrine Specification 102/0200
Document No. 70-0124-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 5 of 8
PE83501
Product Specification
Figure 11. Package Drawing
8-lead MSOP
TOP VIEW
0.65BSC
.525BSC
8
7
6
5
2.45±0.10
2X
3.00±0.10
0.51±0.13
0.51±0.13
- B -
2
3
4
1
.25 A B C
- C -
2.95±0.10
0.86±0.08
2.95±0.10
1.10 MAX
- A -
+0.07
-0.08
3.00±0.10
4.90±0.15
0.10 A
0.33
0.08
0.10±0.05
A B C
3.00±0.10
FRONT VIEW
SIDE VIEW
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0124-02 │ UltraCMOS™ RFIC Solutions
Page 6 of 8
PE83501
Product Specification
Figure 12. Tape and Reel Specifications
8-lead MSOP
Pin1
Table 4. Ordering Information
Order Code
83501-11
Part Marking
PE83501
Description
Package
Shipping Method
50 pcs. / Tube
2000 pcs. / T&R
1 / Box
PE83501-08MSOP-100A
8-lead MSOP
83501-12
PE83501
PE83501-08MSOP-2000C
PE83501-08MSOP-EK
8-lead MSOP
83501-00
PE83501-EK
Evaluation Board
Document No. 70-0124-02 │ www.psemi.com
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Page 7 of 8
PE83501
Product Specification
Sales Offices
The Americas
North Asia Pacific
Peregrine Semiconductor Corporation
Peregrine Semiconductor K.K.
9450 Carroll Park Drive
San Diego, CA 92121
Tel: 858-731-9400
Teikoku Hotel Tower 10B-6
1-1-1 Uchisaiwai-cho, Chiyoda-ku
Tokyo 100-0011 Japan
Fax: 858-731-9499
Tel: +81-3-3502-5211
Fax: +81-3-3502-5213
Europe
Peregrine Semiconductor, Korea
#B-2402, Kolon Tripolis, #210
Geumgok-dong, Bundang-gu, Seongnam-si
Gyeonggi-do, 463-480 S. Korea
Tel: +82-31-728-4300
Peregrine Semiconductor Europe
Bâtiment Maine
13-15 rue des Quatre Vents
F-92380 Garches, France
Tel: +33-1-4741-9173
Fax : +33-1-4741-9173
Fax: +82-31-728-4305
South Asia Pacific
Space and Defense Products
Americas:
Peregrine Semiconductor, China
Shanghai, 200040, P.R. China
Tel: +86-21-5836-8276
Tel: 858-731-9453
Fax: +86-21-5836-7652
Europe, Asia Pacific:
180 Rue Jean de Guiramand
13852 Aix-En-Provence Cedex 3, France
Tel: +33-4-4239-3361
Fax: +33-4-4239-7227
For a list of representatives in your area, please refer to our Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The information in this data sheet is believed to be reliable.
However, Peregrine assumes no liability for the use of this
information. Use shall be entirely at the user’s own risk.
The product is in a formative or design stage. The data
sheet contains design target specifications for product
development. Specifications and features may change in
any manner without notice.
No patent rights or licenses to any circuits described in this
data sheet are implied or granted to any third party.
Preliminary Specification
Peregrine’s products are not designed or intended for use in
devices or systems intended for surgical implant, or in other
applications intended to support or sustain life, or in any
application in which the failure of the Peregrine product could
create a situation in which personal injury or death might occur.
Peregrine assumes no liability for damages, including
consequential or incidental damages, arising out of the use of
its products in such applications.
The data sheet contains preliminary data. Additional data
may be added at a later date. Peregrine reserves the right
to change specifications at any time without notice in order
to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine
decides to change the specifications, Peregrine will notify
customers of the intended changes by issuing a DCN
(Document Change Notice).
The Peregrine name, logo, and UTSi are registered trademarks
and UltraCMOS and HaRP are trademarks of Peregrine
Semiconductor Corp.
©2003-2006 Peregrine Semiconductor Corp. All rights reserved.
Document No. 70-0124-02 │ UltraCMOS™ RFIC Solutions
Page 8 of 8
相关型号:
PE83502_06
3.5 GHz Low Power UltraCMOS Divide-by-4 Prescaler Military Operating Temperature Range
PSEMI
PE83503
3.5 GHz Low Power UltraCMOS Divide-by-8 Prescaler Military Operating Temperature Range
PSEMI
PE83503_06
3.5 GHz Low Power UltraCMOS Divide-by-8 Prescaler Military Operating Temperature Range
PSEMI
PE83511
DC - 1500 MHz Low Power UltraCMOS Divide-by-2 Prescaler Military Operating Temperature Range
PSEMI
PE83511_06
DC - 1500 MHz Low Power UltraCMOS Divide-by-2 Prescaler Military Operating Temperature Range
PSEMI
PE83512
DC - 1500 MHz Low Power UltraCMOS Divide-by-4 Prescaler Military Operating Temperature Range
PSEMI
PE83512_06
DC - 1500 MHz Low Power UltraCMOS Divide-by-4 Prescaler Military Operating Temperature Range
PSEMI
©2020 ICPDF网 联系我们和版权申明