电子元器件数据表 IC PDF查询
English 中文版
  品牌   我要上传
型号:  
描述:
SP3232EHCT  SP3232EHCP  SP3232EHCA  SP3232EHCY  
4444 Transceiver for MIL-STD-1553 /MACAIR in a Chipscale Package
型号:   4444
PDF文件: 下载PDF文件   鼠标右键选目标另存为
网页直接浏览   不需安装PDF阅读软件
在线打开PDF文件   需安装PDF阅读软件
描述:   Transceiver for MIL-STD-1553 /MACAIR in a Chipscale Package
文件大小 :   212 K    10 页
Logo:   
品牌   AEROFLEX [ AEROFLEX CIRCUIT TECHNOLOGY ]
购买 :   
  浏览型号4444的Datasheet PDF文件第2页 浏览型号4444的Datasheet PDF文件第3页 浏览型号4444的Datasheet PDF文件第4页 浏览型号4444的Datasheet PDF文件第5页 浏览型号4444的Datasheet PDF文件第6页 浏览型号4444的Datasheet PDF文件第7页 浏览型号4444的Datasheet PDF文件第8页 浏览型号4444的Datasheet PDF文件第9页  
100%
Standard Products
ACT4444 Transceiver
for MIL-STD-1553 / MACAIR in a Chipscale Package
Preliminary
October 1, 2003
FEATURES
Transceiver meets MIL-STD-1553A & B, Macair A3818, A4905, A5232 and A5690 specs
Bipolar Supply ±15V to ±12V, Logic Supply +5V
Replacement for function of CT3232 & ACT4404 in new designs
Voltage source output
Monolithic construction
Aeroflex is a Class H & K MIL-PRF-38534 Manufacturer
Miniature Chipscale Package Bumped Chip Carrier
(BCC++)
NOTE: BCC++ and Bumped Chip Carrier are Trademarks of Fujitsu Ltd.
GENERAL DESCRIPTION
The Aeroflex Laboratories transceiver model ACT4444 is a monolithic transceiver which provides full compliance with Macair and
MIL-STD-1553 data bus requirements. The model ACT4444 performs the front-end analog function of inputting and outputting data through a
transformer to a MIL-STD-1553 or Macair data bus with a few external components.
The ACT4444 can be considered a "Universal" Transceiver in that it is compatible with MIL-STD-1553A, B, Macair A-3818, A-4905, A-5232
and A-5690.
Design of these transceivers reflects particular attention to active filter performance. This results in low bit and word error rate with superior
waveform purity and minimal zero crossover distortion. The ACT4444 active filter design has additional high frequency roll-off to provide the
required Macair low harmonic distortion waveform without increasing the pulse delay characteristics significantly.
Efficient transmitter electrical and thermal design provides low internal power dissipation and heat rise at high and well as low duty cycles.
An optional receiver input threshold adjustment can be accomplished by the use of the "External Threshold" terminals.
TRANSMITTER
The Transmitter section accepts bi-phase TTL data at the input and when coupled to the data bus with a 1:1 transformer, isolated on the data bus
side with two 55 Ohm fault isolation resistors, and loaded by two 70 thru 85 Ohm terminations plus additional receivers, the data bus signal
produced is 7.0 Volts minimum P-P at A-A’ (See Figure 3 or 4). When both DATA and DATA inputs are held low or high, the transmitter output
becomes a high impedance and is “removed” from the line. In addition, an overriding “INHIBIT" input provides for the removal of the
transmitter output from the line. A logic “1” applied to the “INHIBIT” takes priority over the condition of the data inputs and disables the
transmitter (See Transmitter Logic Waveforms - Figure 1).
The transmitter utilizes an active filter to suppress harmonics above 1 MHz to meet Macair specifications A-3818, A-4905, A-5232 and A-5690.
The transmitter may be safely operated for an indefinite period at 100% duty cycle into a data bus short circuit.
RECEIVER
The Receiver section accepts bi-phase differential data at the input and produces two TTL signals at the output. The outputs are DATA and
DATA, and represent positive and negative excursions of the input beyond a pre-determined threshold (See Receiver Logic Waveforms -
Figure 2).
The internal threshold is nominally set to detect data bus signals exceeding 1.05 Volts P-P and reject signals less than 0.6 Volts P-P when used
with a 1:1 turns ratio transformer (See Figure 3 or 4 for transformer data and typical connections). This threshold setting can be held by
grounding the appropriate pins or modified with the use of external resistors.
A low level at the Strobe input inhibits the DATA and DATA outputs. If unused, a 2K Ohm pull-up to +5 Volts is recommended.
SCD4444 Rev B
首页 - - 友情链接
Copyright© 2001 - 2014 ICPDF All Rights Reserved ICPDF.COM

粤公网安备 44030402000629号


粤ICP备13051289号-7