电子元器件数据表 IC PDF查询
English 中文版
  品牌   我要上传
型号:  
描述:
V23040-B0001B201  V23040-C5102B201  V23040-C5051B201  VFM40-D512_12  VLA513-01R  VFM40-T5245  V23040-A0002B201  V23040-C0103B201  V23040-C2004B201  VGS-50-15  
ML4830CP Electronic Ballast Controller
型号:   ML4830CP
PDF文件: 下载PDF文件   鼠标右键选目标另存为
网页直接浏览   不需安装PDF阅读软件
在线打开PDF文件   需安装PDF阅读软件
描述:   Electronic Ballast Controller
文件大小 :   221 K    15 页
Logo:   
品牌   MICRO-LINEAR [ MICRO LINEAR CORPORATION ]
购买 :   
  浏览型号ML4830CP的Datasheet PDF文件第2页 浏览型号ML4830CP的Datasheet PDF文件第3页 浏览型号ML4830CP的Datasheet PDF文件第4页 浏览型号ML4830CP的Datasheet PDF文件第5页 浏览型号ML4830CP的Datasheet PDF文件第6页 浏览型号ML4830CP的Datasheet PDF文件第7页 浏览型号ML4830CP的Datasheet PDF文件第8页 浏览型号ML4830CP的Datasheet PDF文件第9页  
100%
March 1997
ML4830*
Electronic Ballast Controller
GENERAL DESCRIPTION
The ML4830 is a complete solution for a dimmable, high
power factor, high efficiency electronic ballast.
Contained in the ML4830 are controllers for “boost” type
power factor correction as well as for a dimming ballast.
The Power factor circuit uses the average current sensing
method with a gain modulator and over-voltage
protection. This system produces power factors of better
than 0.99 with low input current THD at > 95%
efficiency. Special care has been taken in the design of
the ML4830 to increase system noise immunity by using a
high amplitude oscillator, and a gain modulator. An over-
voltage protection comparator stops the PFC section in
the event of sudden load decrease.
The ballast section provides for programmable starting
scenarios with programmable preheat and lamp out-of-
socket interrupt times. The IC controls lamp output
through either frequency or Pulse Width control using
lamp current feedback.
The ML4830 is designed using Micro Linear‘s Semi-
Standard tile array methodology. Customized versions of
this IC, optimized to specific ballast architectures can be
made available. Contact Micro Linear or an authorized
representative for more information.
FEATURES
s
Complete Power Factor Correction and Dimming
Ballast Control on one IC
Low Distortion, High Efficiency Continuous Boost,
Average Current sensing PFC section
Programmable Start Scenario for Rapid or Instant Start
Lamps
Selectable Variable Frequency dimming and starting
Programmable Restart for lamp out condition to
reduce ballast heating
Over-Temperature Shutdown replaces external heat
sensor for safety
PFC Over-Voltage comparator eliminates output
“runaway” due to load removal
Large oscillator amplitude and gain modulator
improves noise immunity
s
s
s
s
s
s
s
*This Part Is End Of Life As Of August 1, 2000
BLOCK DIAGRAM
MODE
7
9
R(SET)
R(T)/C(T)
OSCILLATOR
LAMP F.B.
LFB OUT
8
5
6
OUTPUT
DRIVERS
12
10
R(X)/C(X)
INTERRUPT
PRE-HEAT
AND INTERRUPT
TIMERS
PWM OR
FREQUENCY
MODULATOR
OUT B
OUT A
15
14
11
2
1
4
3
20
19
OVP/INHIBIT
IA OUT
IA–
IA+/I(LIM)
I(SINE)
EA OUT
EA–
POWER
FACTOR
CONTROLLER
UNDER-VOLTAGE
AND THERMAL
SHUTDOWN
PFC OUT
16
VCC
V
REF
GND
17
18
13
1
首页 - - 友情链接
Copyright© 2001 - 2014 ICPDF All Rights Reserved ICPDF.COM

粤公网安备 44030402000629号


粤ICP备13051289号-7