QPA4586A [QORVO]
DC â 4000 MHz Cascadable SiGe HBT Amplifier;型号: | QPA4586A |
厂家: | Qorvo |
描述: | DC â 4000 MHz Cascadable SiGe HBT Amplifier |
文件: | 总9页 (文件大小:693K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
QPA4586A
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
®
General Description
The QPA4586A is a high performance SiGe HBT MMIC
Amplifier. A Darlington configuration provides high FT and
excellent thermal performance. The heterojunction
increases breakdown voltage and minimizes leakage
current between junctions. Cancellation of emitter junction
non-linearities results in higher suppression of
intermodulation products. Only two DC-blocking capacitors,
a bias resistor, and an optional RF choke are required for
operation.
4 Lead SOT-86 Package
Product Features
• High Gain: 19.9ꢀdB at 1950ꢀMHz
• Cascadable 50ꢀΩ
• Operates from Single Supply
• Low Thermal Resistance Package
Applications
• Instrumentation
• Repeaters
Functional Block Diagram
• Boosters
• PA Driver Amplifier
• Cellular, PCS, GSM, UMTS
• IF Amplifier
4
• Wireless Data, Satellite
1
3
2
Ordering Information
Part No.
Description
Top View
QPA4586ATR13
3000 pieces on a 13” reel (standard)
QPA4586APCK401 850ꢀMHz, +5ꢀV EVB with 5 Piece Sample Bag
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
1 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Rating
−55 to +150ꢁ°C
+5 V
Parameter
Min
Typ
Max Units
Storage Temp
Operating Temperature
Junction Temperature (TJ)
−55
+105
+125
°C
°C
V
Device Voltage (VD)
Device Current (ID)
RF Input Power
90 mA
Device Operating Voltage +3.2 +3.5 +3.8
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions.
+18 dBm
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability.
Electrical Specifications
Parameter
Conditions
Min
Typ
23.3
19.9
18.6
+15.7
+16.3
+29.7
+30.1
16.3
24.2
2.7
Max
Units
dB
850 MHz
1950 MHz
2400 MHz
850 MHz
1950 MHz
850 MHz
1950 MHz
1950 MHz
1950 MHz
1950 MHz
Small Signal Gain
dB
dB
dBm
dBm
dBm
dBm
dB
Output Power at 1dB Compression
Output Third Intercept Point
Input Return Loss
Output Return Loss
Noise Figure
dB
dB
Device Operating Current
Thermal Resistance, θjc
Notes:
45
mA
86
°C/W
1. Test conditions unless otherwise noted: VS = +8ꢀV, ID = 45ꢀmA Typ., OIP3 Tone Spacing=1ꢀMHz, POUT per tone = 0ꢀdBm, R1 = 100ꢀΩ, 50ꢀΩ system,
Tempꢀ=ꢀ+25ꢀ°C
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
2 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Evaluation Board and Schematicꢀ –ꢀ 850 MHz Application Circuit
Bill of Materialꢀ –ꢀ 850 MHz Application Circuit
Reference Value Description
Manufacturer
Qorvo
Part Number
n/a
n/a
PCB, QPA4586A
QPAXX86A-410(A)
GRM31MR71E105KA01L
GRM155R71H102KA01D
GRM1555C1H680JA01D
GRM1555C1H101JA01D
ERJ-14NF1400U
1ꢀμF
C1
CAP, 10%, 25V, X7R, 1206
CAP, 10%, 50V, X7R, 0402
CAP, 5%, 50V, C0G, 0402
CAP, 5%, 50V, C0G, 0402
RES, 5%, 1/2W, 1210
Murata Electronics
Murata Electronics
Murata Electronics
Murata Electronics
Panasonic Industrial Co
Murata Electronics
Amphenol RF Asia Corp
Qorvo
C2
1000 pF
68 pF
100 pF
100 Ω
33 nH
n/a
C3
C4, C5
R1
L1
IND, 5%, M/L, 0603
LL1608-FSL33NJ
901-10426
J1, J2
U1
CONN, SMA, EL, FLT, 0.068" SPE-000318
HBT MMIC Amplifier
n/a
QPA4586A
J3, J4
n/a
CONN, HDR, ST, 1x2, 0.100", Hi-temp, T/H
Samtec Inc
HTSW-102-07-G-S
Component Values for Specific Frequencies
Frequency
500 MHz
220 pF
100 pF
68 nH
850 MHz
100 pF
68 pF
1950 MHz
68 pF
2400 MHz
3500 MHz
39 pF
C4, C5
C3
56 pF
22 pF
18 nH
22 pF
15 pF
L1
33 nH
22 nH
15 nH
Recommended Bias Resistor Values for Various Supply Voltages
Vsupply
+6 V
+8ꢀV
+10ꢀV
150ꢀΩ
+12ꢀV
180ꢀΩ
R1
51 Ω
100ꢀΩ
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
3 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Typical Performanceꢀ –ꢀ 850 MHz Application Circuit
Parameter
Typical Value
1950
Units
MHz
dB
Frequency
500
24.1
+28.6
+15.2
20.5
13.4
26.5
2.6
850
23.3
+29.9
+15.7
30.0
20.4
25.8
2.4
2400
18.6
+29.6
+16.0
15.4
20.2
23.0
2.9
3500
15.9
+26.4
+14.4
13.0
17.9
21.9
3.2
Small Signal Gain
Output Third Intercept Point
Output Power at 1dB Compression
Input Return Loss
Output Return Loss
Reverse Isolation
Noise Figure
19.9
+30.1
+16.3
16.3
dBm
dBm
dB
24.2
dB
23.7
dB
2.7
dB
Notes:
1. Test conditions: VS = +8ꢀV, ID = 45ꢀmA Typ., OIP3 Tone Spacing=1ꢀMHz, POUT per tone = 0ꢀdBm, R1 = 100ꢀΩ, 50ꢀΩ system, Tempꢀ=ꢀ+25ꢀ°C
Performance Plotsꢀ –ꢀ 850 MHz Application Circuit
Test conditions unless otherwise noted: VS = +8.0 V, ID = 45 mA, Temp.=ꢁ+25ꢁ°C
|S21| vs. Frequency
|S11| vs. Frequency
|S22| vs. Frequency
25
20
15
10
0
-5
0
-5
+105°C
+85°C
+25°C
−40°C
-10
-15
-20
-25
-30
-35
-10
-15
-20
-25
-30
+105°C
+85°C
+25°C
−40°C
+105°C
+85°C
+25°C
−40°C
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
|S12| vs. Frequency
OIP3 vs Frequency
OP1dB vs Frequency
-15
-20
-25
-30
34
31
28
25
22
19
18
16
14
12
10
8
+105°C
+85°C
+25°C
−40°C
+105°C
+85°C
+25°C
−40°C
+105°C
+85°C
+25°C
−40°C
0
1000
2000
3000
4000
5000
500
1000
1500
2000
2500
3000
3500
500
1000
1500
2000
2500
3000
3500
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
Noise Figure vs Frequency
Current vs Voltage
5
4
3
2
1
0.06
0.05
0.04
0.03
0.02
0.01
0.00
+105°C
+85°C
+25°C
−40°C
+105°C
+85°C
+25°C
−40°C
0
1000
2000
3000
4000
0
1
2
3
4
5
6
7
8
9
Frequency (MHz)
VS (V)
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
4 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Pin Configuration and Description
4
1
3
2
Top View
Pad No.
Label
Description
RF Input Pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of
operation.
1
RFIN
Connection to ground. Use via holes in PCB for best performance to reduce lead inductance as close to
ground leads as possible
2, 4
3
GND
RF Output and Bias Input Pin. DC voltage is present on this pin; therefore a DC blocking capacitor is
necessary for proper operation.
RFOUT
Package Marking
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
5 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Package Dimensions
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Dimension and tolerance formats conform to ASME Y15.5-2009.
PCB Mounting Pattern
Notes:
1. All dimensions are in inches (millimeters). Angles are in degrees.
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
6 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Tape and Reel Information – Carrier and Cover Tape Dimensions
Feature
Measure
Symbol
Size (in)
0.257
0.247
0.073
0.314
0.079
0.217
0.366
0.472
Size (mm)
6.53
Length
A0
B0
K0
P1
P2
F
Width
6.27
Cavity
Depth
1.85
Pitch
8.00
Cavity to Perforation - Length Direction
2.00
Centerline Distance
Cavity to Perforation - Width Direction
5.50
Cover Tape
Carrier Tape
Width
Width
C
9.30
W
12.00
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
7 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Tape and Reel Information – Reel Dimensions (13”)
Standard T/R size = 3,000 pieces on a 13” reel.
Feature
Measure
Symbol
Size (in)
12.992
0.717
Size (mm)
330.0
18.2
Diameter
A
W2
W1
N
Flange
Thickness
Space Between Flange
Outer Diameter
Arbor Hole Diameter
Key Slit Width
Key Slit Diameter
0.504
12.8
4.016
102.0
13.0
C
0.512
Hub
B
0.079
2.0
D
0.795
20.2
Tape and Reel Information – Tape Length and Label Placement
Notes:
1. Empty part cavities at the trailing and leading ends are sealed with cover tape. See EIA 481-1-A.
2. Labels are placed on the flange opposite the sprockets in the carrier tape.
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
8 of 9
www.qorvo.com
QPA4586A
®
DCꢀ–ꢀ4000ꢀMHz Cascadable SiGe HBT Amplifier
Handling Precautions
Parameter
Rating
Standard
ESDꢀ–ꢀHuman Body Model (HBM)
Class 1C
ESDAꢁ/ꢁJEDEC JS-001-2014
ESDA / JEDEC JS-002-2014
IPC/JEDEC J-STD-020
Caution!
ESD-Sensitive Device
ESDꢀ–ꢀCharged Device Model (CDM) Class C3
MSLꢀ–ꢀMoisture Sensitivity Level
Level 1
Solderability
Compatible with lead-free (260°C max. reflow temp.) soldering process.
Solder profiles available upon request.
Contact plating: Matte Sn
RoHS Compliance
This part is compliant with 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment) as amended by Directive 2015/863/EU.
This product also has the following attributes:
• Lead Free
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• SVHC Free
Pb
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2021 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
Datasheet Rev. E, March 25, 2021 | Subject to change without notice
9 of 9
www.qorvo.com
相关型号:
©2020 ICPDF网 联系我们和版权申明