LMT3-8692125-5 [RADIOMETRIX]
NBFM Multi-channel transmitter for 868MHz SRD band;
| 型号： | LMT3-8692125-5 |
| 厂家： | 
RADIOMETRIX LTD |
| 描述： | NBFM Multi-channel transmitter for 868MHz SRD band |
| 文件： | 总7页 (文件大小：259K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Hartcran House, 231 Kenton Lane, Harrow, Middlesex, HA3 8RP, England
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233, www.radiometrix.com
Issue 1, 22 January 2013
NBFM Multi-channel transmitter for 868MHz SRD band
The LMT3 is a 25kHz channel narrowband
multichannel transmitter offering up to 25mW RF
power. LMT3 can be paired with the Category 1
compliant receiver intended for European 869.2-
869.25MHz Social Alarm application. It can also be
used for any 868 - 870MHz band Non-Specific SRD
applications. The module offers a low power,
reliable data link in an industry-standard pin out and
footprint.
Figure 1: LMT3 transmitter
Features
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Conforms to EN 300 220-3 and EN 301 489-3
PLL synthesizer with TCXO
Data rates up to 5 kbps for standard module
Usable range over 500m @ 25mW
Fully screened, Low profile
Low power requirements
Applications
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Social Alarm
Handheld terminals
EPOS equipment, barcode scanners
Data loggers
Industrial telemetry and telecommand
In-building environmental monitoring and control
High-end security and fire alarms
DGPS systems
Vehicle data up/download
Heavy vehicle/machinery controls
Technical Summary
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Social Alarm frequencies: CH0: 869.2125MHz, CH1: 869.2375MHz
Custom frequency within 865MHz - 870MHz
32 channels
Transmit power: +10dBm (10mW) / +14dBm (25mW)
Supply range: 3.1 – 15V (TX @ 10mW), 4.1 – 15V (TX @ 25mW)
Current consumption: 34mA @ 10mW, 68mA @ 25mW
Data bit rate: 5kbps max. (standard module)
Serial configuration by inverted RS232 at 3V CMOS level
Evaluation platforms: NBEK + LM Series carrier
Matching receiver: COR3-869-5
Radiometrix Ltd
LMT3 Data Sheet
page 1
Radiometrix Ltd
LMT3 Data Sheet
page 2
Figure 3: LMT3 footprint (top view)
Pin description – LMT3
Pin
1a
Name
Vcc
Function
3.1 – 15V power supply (@ 10mW)
4.1 – 15V power supply (@ 25mW)
Ground
Transmit Enable (active low)
DC coupled input for 3V CMOS logic. Rin=47kΩ
Not present in LMT3
2a
3a
4a
5a
0V
TXE
TXD
No pin
1b
P0/PGM
Parallel Channel select LSB
Serial frequency programming / configuration1
Parallel Channel select
Parallel Channel select
Parallel Channel select MSB
Not present in LMT3
2b
3b
4b
5b
P1
P2
P3
No pin
Notes:
1. Serial programming is by an inverted, CMOS logic level, 2400 baud RS232 datastream applied to
the P0 pin.
2. Channel select inputs have pullups (50kΩ) to 3v internal rail. Do not exceed 3V logic levels on this
port.
3. Channel select inputs are active low
4. TXE has a 100kΩ pullup to Vcc
5. All pins are on an 0.1" grid
6. The pins 5a/b are not present, but are included in footprint for compatibility with other units in this
family
7. In the 'off' state a PIN switch open circuits the RF output pin. There are no 'off' state spuri.
8. 10mW unit will operate (with marginally reduced specifications and lower (6-8mW) output power)
from a 3.0V rail. This must be well regulated and without noise or ripple, as in this state the unit's
internal regulator no longer operates, and provides no supply rejection.
Radiometrix Ltd
LMT3 Data Sheet
page 3
Serial interface commands
2400 baud RS232. 8 bit data, no parity, 1 start bit, 1 or 2 stop bits.
Serial data is sent to the unit on one of the parallel channel select pins (P0). It is very important that the unit
does not 'decode' switch bounce in ordinary operation as a command string, or spurious re-writing of the
e2prom will result. For this reason the user must send the 16 character string ENABLESERIALMODE
(followed by a carriage return) to activate the serial command mode before sending any of the command
strings listed below. Command mode is disabled on power down, or on reception of a # character. To
successfully program the unit, it must be enabled (TXE low).
GOCHAN aa
LOAD aa nnnnn
SETPAR
SETSER
RVALUE rrrr
SINGLE nnnnn
Serially select channel aa, where aa is ch0 to ch31
Set value of N register for channel aa, where aa is Channels 0 to 31
Channel selected by 4 bit parallel inputs (ch0 to ch15 only)
Channel selected by most recent GOCHAN operation
Set value for R register
Set value of N for single channel operation.
N value NOT stored in EEPROM
Process entry
<cr>
/
#
Clear all buffers
Disable command mode
aa = a two digit channel number from 00 to 31
nnnnn = synthesizer N register value (up to 65535)
rrrr = synthesizer R register value (up to 16383)
fTCXO
fRF
869.200MHz
25kHz
13MHz
25kHz
NTX
=
=
= 34768
R =
=
, So R=520
fChannelspacing
fchannelspacing
Note: A pause of at least 50ms must be allowed between command strings (EEPROM
programming time).
SINGLE mode does not store the N value in EEPROM. Therefore the unit is inoperative after
a power down until either another valid SINGLE command is received, or mode is changed
by a GOCHAN, SETPAR or SETSER command. SINGLE mode is intended for frequency
agile applications.
If an N value greater than 65535 is needed then an offset of +65536 can be selected by
setting bit 15 of the R value high (the N value is then reduced by 65536 of course)"
Example: Fout = 869.2125
Fcomp = 12.5KHz
N = 69537 This exceeds 65535, so:
Bit 15 of R is set : RVALUE 33808
65536 is subtracted: LOAD00 4001
Radiometrix Ltd
LMT3 Data Sheet
page 4
Condensed specifications
Frequency
Social Alarm (SAL) variant: CH0: 869.2125MHz, CH1: 869.2375MHz
User customisable frequencies: 865MHz – 870MHz
Frequency stability
Channel spacing
Number of channels
1.5kHz
25kHz
16 channels controlled by parallel port
or 32 via RS232 interface
Operating temperature
Spurious radiations
-10 ºC to +60 ºC (Storage -30 ºC to +70 ºC)
Compliant with ETSI EN 300 220-3 and EN 301 489-3
Transmitter
Output power
+10dBm (10mW) 1dB
+14dBm (25mW) 1dB
3kHz
Peak deviation
TX on switching time
Modulation type
TX modulation bandwidth
Adjacent channel TX power
TX spurious
30ms from TXE transition
FSK (F3D)
DC – 5kHz (3V CMOS compatible)
<-37dBm
<-45dBm (no RF output in Standby)
Supply
Voltage
3.1V – 15V (10mW)
4.1 – 15V (25mW)
Current
34mA @ 10mW (nominal)
68mA @ 25mW (nominal)
<5µA standby (TXE high or floating)
data (CMOS/TTL compatible)
33 x 23 x 9mm
10 (8) pin 0.1" pitch dual row (5+5) header
2pin 0.1” pitch
1.2mm
Inputs
Size
Interface
User
RF
Recommended PCB hole size
Ordering Information:
Part No.
Frequency
(MHz)
869.2125
RF power
(mW)
Channel spacing
(kHz)
Data rate
(kbps)
LMT3-869.2125-5
LMT3-869-5-SAL
LMT3-869-5
10
10
10
25
25
25
25
25
5
5
5
5
869.200 - 869.250
868 - 870
868 - 870
LMT3-869-5-25mW
Matching COR3 receiver
Part Number
Frequency
Module mounting
Horizontal Mounting,
Perpendicular pins
Pins
COR3-869.2125-5-H
869.2125MHz
RF, RFGND, RSSI, GND, VCC, AF, RXD
COR3-869-5-SAL
COR3-869-5-SAL-H
COR3-869-5
869.2-869.25MHz Vertical Mounting,
Parallel pins
RF, RFGND, RSSI, GND, VCC, AF, RXD
P0/PGM
869.2-869.25MHz Horizontal Mounting,
Perpendicular pins
RF, RFGND, RSSI, GND, VCC, AF, RXD
P0/PGM
868-870MHz
Vertical Mounting,
Parallel pins
RF, RFGND, RSSI, GND, VCC, AF, RXD
P3, P2, P1, P0/PGM
Radiometrix Ltd
LMT3 Data Sheet
page 5
Appendix
P ] E [ R E R W P O F R
Radiometrix Ltd
LMT3 Data Sheet
page 6
Radiometrix Ltd
Hartcran House
231 Kenton Lane
Harrow, Middlesex
HA3 8RP
ENGLAND
Tel: +44 (0) 20 8909 9595
Fax: +44 (0) 20 8909 2233
sales@radiometrix.com
www.radiometrix.com
Copyright notice
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in
whole or in part must give clear acknowledgement to the copyright owner.
Limitation of liability
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd
reserves the right to make changes or improvements in the design, specification or manufacture of its
subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the
application or use of any product or circuit described herein, nor for any infringements of patents or other
rights of third parties which may result from the use of its products. This data sheet neither states nor
implies warranty of any kind, including fitness for any particular application. These radio devices may be
subject to radio interference and may not function as intended if interference is present. We do NOT
recommend their use for life critical applications.
The Intrastat commodity code for all our modules is: 8542 6000.
R&TTE Directive
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of
the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance
to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular
equipment.
Further details are available on The Office of Communications (Ofcom) web site:
http://www.ofcom.org.uk/radiocomms/ifi/
Information Requests
Ofcom
Riverside House
2a Southwark Bridge Road
London SE1 9HA
Tel: +44 (0)845 456 3000 or 020 7981 3040
Fax: +44 (0)20 7783 4033
information.requests@ofcom.org.uk
European Radiocommunications Office (ERO)
Peblingehus
Nansensgade 19
DK 1366 Copenhagen
Tel. +45 33896300
Fax +45 33896330
ero@ero.dk
www.ero.dk
相关型号：
LMT393DR2
Comparator, 2 Func, 9000uV Offset-Max, 1300ns Response Time, PDSO8, PLASTIC, SO-8
MOTOROLA
©2020 ICPDF网 联系我们和版权申明