5962-86879013A [RAYTHEON]
Line Driver, 1 Func, 1 Driver, CQCC28,;
| 型号： | 5962-86879013A |
| 厂家： | 
RAYTHEON COMPANY |
| 描述： | Line Driver, 1 Func, 1 Driver, CQCC28, 驱动 接口集成电路 驱动器 |
| 文件： | 总13页 (文件大小：280K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
A
DESCRIPTION
DATE (YR-MO-DA)
89-01-30
APPROVED
M. A. FRYE
Make changes to paragraphs 1.3, 4.3.1c, table I, and figure 3.
Make editorial changes throughout.
B
Add one vendor, CAGE 07933. Make changes to table I and editorial changes
throughout. Remove vendor CAGE 34371. Device 013X is not available from
an approved source of supply.
90-05-30
M. A. FRYE
C
D
Changes in accordance with N.O.R. 5962-R013-91.
Drawing updated to reflect current requirements. - ro
91-09-27
02-07-08
M. A. FRYE
R. MONNIN
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
D
1
D
2
D
3
D
4
D
5
D
6
D
7
D
8
D
9
D
D
D
SHEET
10
11
12
PREPARED BY
DONALD R. OSBORNE
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
CHECKED BY
RAY MONNIN
STANDARD
MICROCIRCUIT
DRAWING
http://www.dscc.dla.mil
APPROVED BY
MICHAEL A. FRYE
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
MICROCIRCUIT, LINEAR, BUS INTERFACE
DRIVER CIRCUIT, MONOLITHIC SILICON
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
88-05-05
AMSC N/A
REVISION LEVEL
D
SIZE
A
CAGE CODE
5962-86879
67268
SHEET
1
OF
12
DSCC FORM 2233
APR 97
5962-E375-02
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-86879
01
E
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
Circuit function
HS-3182, HI-8382
Bus interface line driver circuit
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
E
3
GDIP1-T16 or CDIP2-T16
CQCC1-N28
16
28
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
V+ minus V- (differential voltage) ..................................................... 40 V dc
V
V
.................................................................................................... 7 V dc
1
.................................................................................................. 6 V dc
REF
Logic input voltage range ................................................................. (GND - 0.3 V) to (V + 0.3 V)
1
Maximum power dissipation (P ):
D
Case E .......................................................................................... 1.725 W 1/
Case 3 .......................................................................................... 1.12 W
1/
Junction temperature (T ) ................................................................ +175°C
J
Lead temperature (soldering, 10 seconds) ...................................... +275°C
Storage temperature range .............................................................. -65°C to +150°C
Thermal resistance, junction-to-case (θJC) ...................................... See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case E .......................................................................................... 86.5°C/W
Case 3 .......................................................................................... 133.7°C/W
_____
1/ Derate above +25°C, 11.5 mW/°C for case E, and 7.5 mW/°C for case 3.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-86879
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
2
DSCC FORM 2234
APR 97
1.4 Recommended operating conditions. 2/
Supply voltage:
V+ ................................................................................................ 15 V dc ±10%
V- ................................................................................................ -15 V dc ±10%
V
V
................................................................................................ 5 V dc ±5%
1
.............................................................................................. 5 V dc ±5%
REF
Ambient operating temperature range (T ) ...................................... -55°C to +125°C
A
Maximum load:
Data rate at 12.5 KBPS: R = 800 Ω, C = 30 nF; R = 400 Ω, C = 6.9 nF.
L
L
L
L
Data rate at 100 KBPS: R = 800 Ω, C = 4 nF.
L
L
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883
-
Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
_____
2/ All voltages referenced to GND
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
3
DSCC FORM 2234
APR 97
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Conditions
-55°C ≤ T ≤ +125°C
Group A
subgroups
Device
type
Limits
Unit
A
Test
Symbol
unless otherwise specified
No load (0-100 k bits/s)
No load (0-100 k bits/s)
No load (0-100 k bits/s)
Min
Max
16
Supply current V+
(operating)
1,2,3
1,2,3
1,2,3
01
01
01
mA
I
CCOP
(V+)
Supply current V-
(operating)
-16
mA
I
CCOP
(V-)
975
µA
Supply current V
(operating)
I
CCOP
1
(V )
1
No load (0-100 k bits/s)
1,2,3
01
-1.0
mA
Supply current V
(operating)
I
CCOP
REF
(V
REF
)
Supply current V-
Short to ground 1/
Short to ground 1/
Short to ground, 2/
1,2,3
1,2,3
1,2,3
01
01
01
-150
150
mA
mA
mA
I
SC
(during short circuit test)
(V-)
Supply current V+
I
SC
(during short circuit test)
(V+)
Output short circuit
current (output high)
-80
I
OSHC
V
min
= 0 V
Output short circuit
current (output low)
Short to ground, 2/
= 0 V
1,2,3
01
+80
mA
I
OSLC
V
min
Input current (input high)
Input current (input low)
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
4
01
01
01
01
01
01
01
10
µA
µA
V
I
I
IH
IL
-20
Output voltage high
(output to ground)
Output voltage low
(output to ground)
Output voltage null
No load (0-100 k bits/s)
No load (0-100 k bits/s)
No load (0-100 k bits/s)
V
V
V
+V
- .25
+V
REF
+ .25
OH
REF
V
-V
REF
-V
REF
OL
- .25
+ .25
-250
+250
mV
pF
NULL
Input capacitance
Functional tests
30
C
See 4.3.1c, T = +25°C
A
IN
7,8
V
V
= 2.0 V,
3/
IH
= 0.5 V, see 4.3.1d
IL
See footnotes at end of table.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Conditions
-55°C ≤ T ≤ +125°C
Group A
subgroups
Device
type
Limits
Max
Unit
A
Test
Symbol
unless otherwise specified
Min
0.9
See figure 4,
3/
3/
3/
3/
9,10,11
9,10,11
9,10,11
9,10,11
01
01
01
01
2.4
2.4
3.3
3.3
µs
Rise time (A
, B
)
t
OUT OUT
r
C = 75 pF
L
See figure 4,
0.9
µs
µs
µs
Fall time (A
, B
)
t
t
t
OUT OUT
f
C = 75 pF
L
Propagation delay input
to output
See figure 4,
PLH
PHL
C = 75 pF
L
Propagation delay input
to output
See figure 4,
C = 75 pF
L
1/ Not tested, but characterized at initial device design and after major process or design change which affects this
parameter.
2/ Interchangeability of force and sense is acceptable.
3/ V+ = 15 V, V- = 15 V, V = V
= 5.0 V.
1
REF
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015 of MIL-STD-883.
(2) T = +125°C, minimum.
A
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
6
DSCC FORM 2234
APR 97
Device type
Case outlines
Terminal
number
01
E
3
Terminal symbol
1
V
REF
V
REF
2
3
4
5
GND
SYNC
NC
GND
SYNC
NC
DATA (A)
C
A
6
DATA (A)
A
OUT
7
8
9
-V
NC
NC
GND
+V
C
A
10
11
NC
NC
NC
B
OUT
12
13
NC
C
B
DATA (B)
A
OUT
14
15
16
CLOCK
NC
-V
GND
+V
V
1
17
---
B
OUT
18
19
20
21
22
---
---
---
---
---
NC
NC
NC
NC
C
B
23
24
25
26
27
28
---
---
---
---
---
---
DATA (B)
NC
CLOCK
NC
NC
V
1
NC = No connection
FIGURE 1. Terminal connections.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
7
DSCC FORM 2234
APR 97
SYNC
CLOCK
DATA (A)
DATA (B)
COMMENTS
NULL
A
B
OUT
OUT
X
L
L
X
H
H
H
H
X
X
L
X
X
L
0 V
0 V
0 V
0 V
0 V
0 V
NULL
H
H
H
H
NULL
L
H
L
LOW
-V
+V
REF
REF
H
H
HIGH
+V
-V
REF
REF
H
0 V
0 V
NULL
FIGURE 2. Truth table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-86879
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
8
DSCC FORM 2234
APR 97
FIGURE 3. Logic diagram.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-86879
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
9
DSCC FORM 2234
APR 97
NOTE:
t measured 50 percent to 90 percent times two.
r
t measured 50 percent to 90 percent times two.
f
V
= 2.0 V
= 0.5 V
V
V
= -4.75 V to -5.25 V
= 4.75 V to 5.25 V
IH
IL
OL
V
OH
FIGURE 4. Switching waveforms.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
10
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
---
Interim electrical parameters
(method 5004)
Final electrical test parameters
(method 5004)
1*,2,3,7,8,9
1,2,3,4,7,8,9,10,11
1,2,3
Group A test requirements
(method 5005)
Groups C and D end-point
electrical parameters
(method 5005)
* PDA applies to subgroup 1.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c. Subgroup 4 (C measurement) shall be measured only for the initial test and after process or design changes which
IN
may affect input capacitance. Sample size is 15 devices, all input and output terminals tested, and no failures.
d. Subgroups 7 and 8 shall include verification of the truth table.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2)
T = +125°C, minimum.
A
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
11
DSCC FORM 2234
APR 97
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
SIZE
STANDARD
5962-86879
A
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
SHEET
D
12
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 02-07-08
Approved sources of supply for SMD 5962-86879 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
34371
Vendor
similar
PIN 2/
5962-8687901EA
HS1-3182/883
44270
3/
HI-8382CM-03
HI-8382CM-02
RM3182S/883B
HI-8382SM-02
HS4-3182/883
3/
5962-86879013A
3/
3/
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item acquisition.
Items acquired to this number may not satisfy the
performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
34371
Intersil Corporation
P.O. Box 883
Melbourne, FL 32902-0883
44270
Holt Integrated Circuits, Inc.
23351 Madero
Mission Viejo, CA 92691-2730
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
5962-8688001XX
Serial I/O Controller, 1 Channel(s), 0.01220703125MBps, CMOS, CQCC44, CERAMIC, LCC-44
WEDC
©2020 ICPDF网 联系我们和版权申明