RACV12-24-LP [RECOM]
Terminal Block Input/Output with Cable Clamps;
| 型号： | RACV12-24-LP |
| 厂家： | 
RECOM INTERNATIONAL POWER |
| 描述： | Terminal Block Input/Output with Cable Clamps |
| 文件： | 总4页 (文件大小：465K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
• Low Profile Case (13mm height max.)
• 12V and 24V Constant Voltage Outputs
• Terminal Block Input/Output with Cable Clamps
• Fully Protected (OLP, SCP, OCP, OTP)
• low Standby Power, ErP conform
• low cost
Features
AC/DC Converter
LED
Driver
RACV12-LP
12 Watt
Constant
Description
These low profile constant voltage LED drivers have been designed for cost-sensitive applications.
The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.
Their low profile design allows them to be invisibly built into furniture, discreetly mounted under shelves
or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lighting sys-
tems. The power supplies are short circuit and overload protected and come with a full 3-year warranty.
Voltage Single
Output
Selection Guide
Part
Number
nom. Input
Voltage
[VAC]
Input
Current
[mA]
Output
Voltage
[VDC]
Output
Current Range
[mA]
Efficiency
typ.
Output
Power max.
[W]
[%]
RACV12-12-LP
RACV12-24-LP
230
230
130
130
12
24
0-1000
0-500
78
80
12W
12W
All LED Drivers may not be used without a load. They must be switched on the primary side only.
Noncompliance may damage the LED or reduce its lifetime.
Specifications (measured @ ta= 25°C, 240VAC and rated load)
BASIC CHARACTERISTICS
Parameter
Input Voltage Range
Inrush Current
Condition
Min.
198VAC
Typ.
230VAC
Max.
264VAC
8A
ERP
compliant
Start-up Time
50ms
63Hz
Input Frequency Range
No Load Power Consumption
Power Factor
47Hz
0.4W
0.55
full load, 230VAC
full load
Internal Operating Frequency
35kHz
140kHz
IEC/EN61347-1 Certified
IEC/EN61347-2-13 Certified
ENEC Certified
12Vout
24Vout
600mVp-p
500mVp-p
Output Ripple Voltage(1)
CB Report
Notes:
EN55015 Compliant
Note1: Measured at 20MHz BW using 0.1µF & 47µF parallel capacitor.
REGULATIONS
Parameter
Output Voltage Accuracy
Line Regulation
Condition
Value
5ꢀ maꢁ.
3ꢀ maꢁ.
3ꢀ maꢁ.
Load Regulation
www.recom-power.com
REV.: 0/2016
L-1
RACV12-LP
AC/DC Converter
Specifications (measured @ ta= 25°C, 240VAC and rated load)
Series
PROTECTION
Parameter
Condition
Value
Input Fuse
eꢁternal fuse is recommended
T1A
Open Circuit Protection (OCP)
Over Load Protection (OLP)
Over Voltage Protection (OVP)
Over Temperature Protection (OTP)
Isolation Voltage
auto recovery after fault condition is removed
auto recovery after fault condition is removed
auto recovery after fault condition is removed
auto recovery after fault condition is removed
3.75kVAC / 1 minute
110°C Tcase
I/P to O/P
Maximum loading of automatic circuit breakers
@ 230VAC, 1Ohm, 90° phase angle and max. load
Circuit Breaker
Circuit Breaker Current
Typ
B
10A
17
16A
28
20A
35
25A
44
C
37
59
74
92
ENVIRONMENTAL
Parameter
Condition
Value
Operating Temperature Range
Maꢁimum Case Temperature
Operating Altitude
Operating Humidity
IP Rating
-20°C to +50°C, Ambient
+85°C
2000m
5ꢀ to 85ꢀ RH, non condensing
IP20
PD2
Pollution Degree
Design Lifetime
30 ꢁ 10³ hours
Derating Graph
100
80
60
40
20
0
-20 -10
0
10
20 30
40
50 60
Ambient Temperature [°C]
SAFETY AND CERTIFICATIONS
Certificate Type
Report Number
Standard
IEC61347-1, 2nd Edition, 2012
EN61347-1, 2nd Edition 2013
Lamp Controlgear General Requirments for Safety
305987
+
305985
IEC61347-2-13, 2nd Edition, 2014
EN61347-2-13, 2014
Lamp Controlgear Particular Requirements
D.C. or A.C. Controlgears for LED Performance Requirements
RoHS 2.1
305984-1 + 305984-1
LCS1606201548R
IEC/EN62384, 1st Edition, 2009
RoHS-2011/65/EU + AM-2015/863
continued on next page
REV.: 0/2016
L-2
www.recom-power.com
RACV12-LP
AC/DC Converter
Specifications (measured @ ta= 25°C, 240VAC and rated load)
Series
EMI Compliance
Standard / Criterion
Equipment for general Lighting Purpose - EMC Immunity Requirements
EN61547, 2009
305984
Limits and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment
+
EN55015, 2015
305985
Assessment of lighting equipment related to human eꢁposure to electromagnetic fields
EN61493, 2015
8kV Air Discharge,
4kV Contact Discharge
ESD Electrostatic discharge immunity test
EN61000-4-2, 2009, Criteria B
EN61000-4-3, 2010, Criteria A
EN61000-4-4, 2012, Criteria B
Radiated, radio-frequency, electromagnetic field immunity test
Fast Transient and Burst Immunity
3V/m
0.5kV (DC Output)
1kV (AC Input)
Surge Immunity
0.5kV (AC Input)
3V
EN61000-4-5, 2014, Criteria C
EN61000-4-6, 2014, Criteria A
Immunity to conducted disturbances, induced by radio-frequency fields
95ꢀ reduction
30ꢀ reduction
EN61000-4-11, 2014, Criteria B
EN61000-4-11, 2014, Criteria C
Voltage Dips and Interuptions
Limits of Harmonic Current Emissions
EN61000-3-2, Class C, 2014
EN61000-3-3, 2013
Voltage Fluctuations and Flicker in Public Low-Voltage Systems <=16A per phase
DIMENSION and PHYSICAL CHARACTERISTICS
Parameter
Material
Type
Case
Value
Plastic (UL94V-2)
128.0 ꢁ 50.0 ꢁ 13.0mm
70g
Package Dimension (LꢁWꢁH)
Package Weight
Mechanical Dimensions
tc
52.0
3
4
1
2
wire preparation
M3 Screws
6-7mm
FC 115.0
128.0
50.0
2 mounting screws are included
Connection via Screw Terminal
wire stripping length: 6-7mm
#
Function
Solid Wire
Stranded Wire (2)
0.75-1.5mm²
0.75-1.5mm²
0.5-1.5mm²
AWG
20-16
20-16
21-16
21-16
recommended tightening torque: 0.25Nm
tc= case temperature measuring point
FC= fiꢁing centers
1
VAC in (N) 0.75-1.5mm²
2
VAC in (L) 0.75-1.5mm²
NC= no connection
3
4
LED+
LED-
0.5-1.5mm²
0.5-1.5mm²
Tolerance: ꢁꢁ.ꢁ=
0.5mm
0.5-1.5mm²
ꢁꢁ.ꢁꢁ= 0.35mm
Notes:
Note2: The use of sleeve or ferrule terminations is recommended.
www.recom-power.com
REV.: 0/2016
L-3
RACV12-LP
AC/DC Converter
Specifications (measured @ ta= 25°C, 240VAC and rated load)
Series
INSTALLATION and APPLICATION
Connection
L N
LED+
LED-
PACKAGING INFORMATION
Parameter
Packaging Dimension (LꢁWꢁH)
Packaging Quantity
Type
Value
265.0 ꢁ 139.0 ꢁ 62.0mm
10pcs
Cardboard Boꢁ
Storage Temperature Range
Storage Humidity
-20°C to +70°C
5ꢀ - 85ꢀ RH
The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s eꢁplicit written
consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be eꢁpected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer
shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.
L-4
REV.: 0/2016
www.recom-power.com
相关型号：
©2020 ICPDF网 联系我们和版权申明