RPA30-2412SAW [RECOM]
4:1 Wide Input Voltage Range;型号: | RPA30-2412SAW |
厂家: | RECOM INTERNATIONAL POWER |
描述: | 4:1 Wide Input Voltage Range |
文件: | 总6页 (文件大小:1038K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
• 4:1 Wide Input Voltage Range
• 1.6kVDC Isolation
Features
DC/DC Converter
• UL, IEC/EN & EN50155 Pending
• Efficiency up to 89%
Regulated
Converters
• OVP, OCP & OTP
• +105°C max Case Temperature
RPA30-AW
30 Watt
1“x1“
Single & Dual
Output
Description
The RPA30-AW series are high power density, wide input voltage range 30W DC/DC converters in
an industry standard 1”x1” case size. Despite their small size, the RPA30-AW converters are fully
specified devices with output currents up to 7.5Amps, up to 89% efficiency, no minimum load, 1600VDC
isolation, tight regulation and low ripple/noise figures. The outputs are also fully protected against
over-temperature, short circuits, overcurrent and overvoltage and the single output version
offers a 10% trim range. A heatsink option is available to extend the operating temperature range.
The converters are UL and EN50155 pending and will find many uses in railway and industrial
applications where board space is at a premium.
Selection Guide
Part Number
Input
Output
Output
Current
[mA]
7500
6000
2500
2000
1250
1000
Input(1) Efficiency(1) Max. Capacitive
Voltage Range Voltage
Current
[mA]
typ.
[%]
Load
[µF]
[VDC]
9-36
9-36
9-36
9-36
9-36
9-36
[VDC]
3.3
5
12
15
RPA30-243.3SAW(2,3)
RPA30-2405SAW(2,3)
RPA30-2412SAW(2,3)
RPA30-2415SAW(2,3)
RPA30-2412DAW(2,3)
RPA30-2415DAW(2,3)
1170
1450
1450
1450
1450
1450
88
89
88
88
88
88
10000
10000
1000
1000
1000
680
12
15
Notes:
Note1:
Efficiency is tested by nominal Vin, full load and at 25°C.
E224736
UL60950-1 Pending
IEC/EN60950 Pending
EN50155 Pending
Model Numbering
RPA30-__ __ _AW/_ _
Package(3)
Input Voltage
CTRL Logic(2)
Output Voltage
Single or Dual
Ordering Examples
RPA30-243.3SAW = 24V Input, 3.3V Output, Single, no CTRL pin
RPA30-2405SAW/P = 24V Input, 5V Output, Single, Pos. CTRL function
RPA30-2415SAW-HC = 24V Input, 15V Output, Single, no CTRL pin, glued Heat-sink
RPA30-2415DAW/N-HC = 24V Input, 15V Output, Dual, Neg. CTRL function, glued Heat-sink
Notes:
Note2: part without suffixes is without CTRL pin, trim pin fitted
add suffix “P” for positive CTRL function (1=ON, 0=OFF), trim pin fitted
add suffix “N” for negative CTRL function (0=ON, 1=OFF), trim pin fitted
trim pin is only available for single outputs
Note3: add suffix “-HC” for glued Heat-sink (compatible with all other suffixes)
www.recom-power.com
REV.: 0/2016
PD-1
RPA30-AW
DC/DC Converter
Specifications measured @ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted
Series
BASIC CHARACTERISTICS
Parameter
Condition
Min.
Typ.
Max.
Internal Input Filter
Input Voltage Range
Input Surge Voltage
Quiescent Current
Pi-Type
9VDC
24VDC
36VDC
50VDC
100ms
Power up
CTRL ON/OFF
Start-up time
8ms
16ms
Internal Operating Frequency
Minimum Load
550kHz
0%
Ripple and Noise
20MHz BW, 10µF tantalum capacitor and 1µF ceramic capacitor
50mVp-p
DC-DC ON
DC-DC OFF
8VDC
7VDC
8.5VDC
7.5VDC
9VDC
8VDC
Under Voltage Lockout (UVLO)
ON/OFF Control
DC-DC ON
Positive Logic
2.4VDC
-0.7VDC
10VDC
0.8VDC
DC-DC OFF
DC-DC ON
Negative Logic
-0.7VDC
2.4VDC
0.8VDC
10VDC
DC-DC OFF
6mA
Input current of CTRL pin
Output Trim
Single Outputs
-10%
+10%
RPA30-2405SAW
Efficiency vs. Output Current
Power Dissipation vs Output Current
5.5
100
90
80
70
60
50
40
30
20
10
0
5
4.5
4
3.5
3
2.5
2
9Vin
24Vin
36Vin
1.5
9Vin
24Vin
36Vin
1
0.5
0
0
10
20
30
40
50
60
70
80
90
100
0
1
2
3
4
5
6
Output Current [%]
Output Current [A]
RPA30-2412SAW
Efficiency vs. Output Current
Power Dissipation vs Output Current
5.5
100
90
5
4.5
4
80
70
60
50
40
30
20
10
0
3.5
3
2.5
2
1.5
1
9Vin
24Vin
36Vin
9Vin
24Vin
36Vin
0.5
0
0
0.5
1
1.5
2
2.5
0
10
20
30
40
50
60
70
80
90
100
Output Current [%]
Output Current [A]
continued on next page
REV.: 0/2016
PD-2
www.recom-power.com
RPA30-AW
DC/DC Converter
Specifications measured @ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted
Series
OUTPUT TRIM
Output Voltage Trimming
RPA30-AW converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim
resistors. The values for trim resistors shown in trim tables below are according to standard E96 values; therefore, the specified voltage may
slightly vary.
5
5
R
U
R
D
6
4
RPA30-243.3SAW
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
%
3.33
402
3.36
169
3.39
100
3.43
75
3.46
47.5
3.49
34.8
3.53
26.1
3.56
17.8
3.59
12.1
3.63
8.06
Volts
KOhms
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
%
3.27
402
3.23
191
3.20
113
3.17
75
3.14
52.3
3.10
39.2
3.07
26.7
3.04
20
3.0
12.1
2.97
8.06
Volts
KOhms
RPA30-2405SAW
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
%
5.05
604
5.10
243
5.15
147
5.20
95.3
5.25
68.1
5.30
39.2
5.35
34.8
5.40
22.1
5.45
15
5.50
8.06
Volts
KOhms
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
4.50
0.5
%
4.95
604
4.90
287
4.85
169
4.80
124
4.75
105
4.70
78.7
4.65
54.9
4.60
39.2
4.55
15
Volts
KOhms
RPA30-2412SAW
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
13.20
10
%
12.12
604
12.24
267
12.36
162
12.48
105
12.6
75
12.72
499
12.84
40.2
12.96
24.9
13.08
18.2
Volts
KOhms
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
%
11.88
750
11.76
309
11.64
200
11.52
124
11.40
90.9
11.28
64.9
11.16
45.3
11.04
32.4
10.92
20
10.80
12.1
Volts
KOhms
RPA30-2415SAW
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
16.50
10
%
15.15
1000
15.30
243
15.45
200
15.60
130
15.75
90.9
15.90
61.9
16.05
40.2
16.20
30.1
16.35
24.9
Volts
KOhms
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
%
14.85
1000
14.70
348
14.55
210
14.40
140
14.25
95.3
14.10
68.1
13.95
45.3
13.80
30.1
13.65
18.2
13.50
8.06
Volts
KOhms
www.recom-power.com
REV.: 0/2016
PD-3
RPA30-AW
DC/DC Converter
Specifications measured @ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted
Series
REGULATION
Parameter
Output Accuracy
Condition
Single & Dual
Single
Value
2.0% max.
0.2% max.
0.5% max.
Line Regulation
Load Regulation
low line to high line
Dual
3.3Vout
5Vout
12Vout, 15Vout
12Vout, 15Vout
0.3%
0.2%
0.1%
1.0%
Cross Regulation
asymmetrical 25%<>100% load
50-75%, full load, 0.1A/µs
25% load step change
3.0% max.
3.0% Vout typ.
250µs typ.
Transient Response
PROTECTION
Parameter
Condition
below 100mΩ
Value
continuous, auto recovery
115%-150% Output Voltage, Hiccup, auto recovery
110%-160% Output Current, Hiccup
115°C 5°C
Short Circuit Protection (SCP)
Over Voltage Protection (OVP)
Over Current Protection (OCP)
Over Temperature Protection (OTP)
Isolation Voltage
Output Voltage 10% low
I/P to O/P
1.6kVDC/1 minute
Isolation Resistance
10MΩ min.
Isolation Capacitance
Notes:
1100pF typ.
Note4: An input fuse is required if the mains supply is not over-current protected. Recommended fuse: 4A slow blow type.
ENVIRONMENTAL
Parameter
Operating Temperature Range (5)
Maximum Case Temperature
Temperature Coefficient
Condition
Value
refer to derating graph
+105°C
0.02%/°C
vertical direction by natural convection without Heat-sink
vertical direction by natural convection with Heat-sink
18°C/W
16°C/W
Thermal Impedance
Operating Altitude
Operating Humidity
MTBF
2134m
95% RH
5888x 103h
Derating Graph (5)
(@ Chamber and natural convection 0.1m/s)
RPA30-24xxSAW
RPA30-24xxSAW-HC
100
100
80
80
60
40
60
40
30
30
20
20
0
0
120
120
60
-40 -20
0
20 40
38
60 80 100
73
-40 -20
0
20 40
46
80 100
77
Ambient Temperature [°C]
Ambient Temperature [°C]
Notes:
Note5: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not
shown here please contact our technical support service team at techsupportAT@recom-power.com
PD-4
REV.: 0/2016
www.recom-power.com
RPA30-AW
DC/DC Converter
Specifications measured @ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted
Series
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
Report / File Number
Standard
E224736
pending
UL60950-1, 2nd Edition, 2014
CSA C22.2 No. 60950, 2nd Edition, 2014
Information Technology Equipment, General Requirements for Safety
E224736-A42+A43
pending
IEC60950-1, 2nd Edition, 2005
EN60950-1, 1st Edition, 2005
IEC/EN Information Technology Equipment - General Requirments for Safety (CB Scheme)
EN Information Technology Equipment - General Requirments for Safety (LVD Directive)
Railway Applications - Electrical Equipment used on rolling stock
pending
pending
EN60950-1, 1st Edition, 2006
EN50155, 1st Edition, 2007
EMC Compliance (designed to meet)
Condition
Standard / Criterion
Information technology equipment - Radio disturbance characteristics Limits and methods
of measurement
with external filter
EN55022, Class A, 2010
EMI Filtering EN55022 Class A
L1
Fuse
+V
IN
C1
-V
IN
L1
Fuse
+V
IN
C1
-V
IN
MODEL
C1
L1
47µF/50V
electrolyt capacitor
RPA30-xxyyS_DAW
1µH
DIMENSIONS and PHYSICAL CHARACTERISTICS
Parameter
Type
Case
Baseplate
Value
Al Alloy, anodize black
non-conductive FR4
Silicone
Material
Potting
without Heat-sink
with Heat-sink
25.4 x 25.4 x 10.2mm
25.4 x 25.4 x 16.8mm
Package Dimensions (LxWxH)
Package Weight
without Heat-sink
with Heat-sink
17g
21g
continued next page
REV.: 0/2016
www.recom-power.com
PD-5
RPA30-AW
DC/DC Converter
Specifications measured @ta = 25°C, resistive load, nominal Vin and rated Iout unless otherwise noted
Series
Dimension Drawing (mm)
25.4
Ø 1.0
Pin Connections
recommended Layout:
Top View
Pin #
Single
+Vin
Dual
+Vin
2.54
20.32
6 x Ø1.5
1
2
3
4
5
6
-Vin
-Vin
6
5
4
3
4
5
6
CTRL(2)
-Vout
Trim
CTRL(2)
-Vout
Com
2
1
1
2
Bottom View
+Vout
+Vout
Pin Pitch Tolerance 0.25mm
Pin dimension tolerance 0.1mm
XX.X 0.5mm
3
XX.XX 0.25mm
Heat-sink Dimension Drawing (mm)
Top View
Heat-sink
25.4
25.4
PACKAGING INFORMATION
Parameter
Type
Value
without Heat-sink
with Heat-sink
285.0 x 27.6 x 19.0mm
285.0 x 27.6 x 25.8mm
Packaging Dimensions (LxWxH)
Tube
Packaging Quantity
10pcs
-55°C to +125°C
5% - 95% RH
Storage Temperature Range
Storage Humidity
The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written
consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer
shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.
PD-6
REV.: 0/2016
www.recom-power.com
相关型号:
©2020 ICPDF网 联系我们和版权申明