ISL22416WFU10Z-TK [RENESAS]
Low Noise, Low Power, SPI® Bus, 128 Taps; DFN10, MSOP10; Temp Range: -40° to 125°C;型号: | ISL22416WFU10Z-TK |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | Low Noise, Low Power, SPI® Bus, 128 Taps; DFN10, MSOP10; Temp Range: -40° to 125°C 光电二极管 转换器 电阻器 |
文件: | 总14页 (文件大小:862K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATASHEET
NOT RECOMMENDED FOR NEW DESIGNS
POSSIBLE SUBSTITUTE PRODUCT
ISL22316
ISL22416
FN6227
Rev 2.00
September 9, 2009
Single Digitally Controlled Potentiometer (XDCP™) Low Noise, Low Power, SPI®
Bus, 128 Taps
The ISL22416 integrates a single digitally controlled
potentiometer (DCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
Features
• 128 resistor taps
• SPI serial interface
The digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wiper is controlled by the user through the SPI
serial interface. The potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up, the device recalls the contents of the
DCP’s IVR to the WR.
• Non-volatile storage of wiper position
• Wiper resistance: 70 typical @ V
• Shutdown mode
= 3.3V
CC
• Shutdown current 5µA max
• Power supply: 2.7V to 5.5V
• 50kor 10k total resistance
• High reliability
The DCP can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide variety of
applications including control, parameter adjustments, and
signal processing.
- Endurance: 1,000,000 data changes per bit per register
- Register data retention: 50 years @ T +55°C
• 10 Ld MSOP and 10 Ld TDFN package
• Pb-free (RoHS compliant)
Pinout
ISL22416
(10 LD MSOP)
TOP VIEW
ISL22416
(10 LD TDFN)
TOP VIEW
O
10
10
1
2
3
4
5
SCK
SDO
SDI
VCC
SCK
SDO
SDI
VCC
RH
1
2
3
4
5
9
8
RH
9
RW
RW
RL
8
7
7
6
CS
CS
RL
SHDN
SHDN
GND
GND
6
Ordering Information
PART NUMBER
(Note)
RESISTANCE OPTION
TEMP. RANGE
(°C)
PACKAGE
(Pb-free)
PART MARKING
416UZ
(k)
PKG. DWG. #
M10.118
ISL22416UFU10Z*
ISL22416UFRT10Z*
ISL22416WFU10Z*
ISL22416WFRT10Z*
50
50
10
10
-40 to +125
-40 to +125
-40 to +125
-40 to +125
10 Ld MSOP
416U
10 Ld 3x3 TDFN
10 Ld MSOP
L10.3x3B
M10.118
416WZ
416W
10 Ld 3x3 TDFN
L10.3x3B
*Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN6227 Rev 2.00
September 9, 2009
Page 1 of 14
ISL22416
Block Diagram
V
CC
SCK
SDO
SDI
POWER-UP
INTERFACE,
CONTROL
AND
RH
SPI
INTERFACE
STATUS
LOGIC
CS
RW
RL
WR
IVR
NON-VOLATILE
REGISTER
SHDN
GND
Pin Descriptions
MSOP/TDFN PIN NUMBER
SYMBOL
SCK
SDO
SDI
DESCRIPTION
1
2
SPI interface clock input
Push-pull/Open Drain Data Output of the SPI serial interface
Data Input of the SPI serial interface
Chip Select active low input
Shutdown active low input
Device ground pin
3
4
CS
5
SHDN
GND
RL
6
7
“Low” terminal of DCP
8
RW
“Wiper” terminal of DCP
9
RH
“High” terminal of DCP
10
V
Power supply pin
CC
FN6227 Rev 2.00
September 9, 2009
Page 2 of 14
ISL22416
Absolute Maximum Ratings
Thermal Information
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
Thermal Resistance (Typical)
(°C/W)
(°C/W)
JC
JA
10 Lead MSOP (Note 2). . . . . . . . . . . .
10 Lead TDFN (Notes 2, 3) . . . . . . . . .
Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
162
74
N/A
7
with Respect to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to V +0.3
CC
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to +6V
CC
Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to V
CC
(10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
I
W
Latchup (Note 1) . . . . . . . . . . . . . . . . . . Class II, Level B @ +125°C
ESD
Recommended Operating Conditions
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5kV
Charge Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV
Temperature Range (Extended Industrial). . . . . . . .-40°C to +125°C
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CC
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±3.0mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -1V for all pins.
2. is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
JA
Tech Brief TB379.
3. For , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
Analog Specifications Over recommended operating conditions, unless otherwise stated. Parameters with MIN and/or MAX limits are
100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not
production tested.
TYP
SYMBOL
PARAMETER
to R Resistance
TEST CONDITIONS
MIN
(Note 4)
MAX
UNIT
k
R
R
R
W option
U option
10
TOTAL
H
L
50
k
to R Resistance Tolerance
W and U option
W option
-20
+20
%
H
L
End-to-End Temperature Coefficient
±50
±80
70
ppm/°C
(Note 18)
U option
ppm/°C
(Note 18)
R
Wiper Resistance
V
V
= 3.3V, wiper current = V /R
CC TOTAL
200
V
W
CC
RH
V
, V
RH RL
V
and V Terminal Voltages
RL
and V to GND
RL
0
V
CC
RH
C /C /C
W
(Note 18)
Potentiometer Capacitance
10/10/25
0.1
pF
H
L
I
Leakage on DCP Pins
Voltage at pin from GND to V
1
1
µA
LkgDCP
CC
VOLTAGE DIVIDER MODE (0V @ R ; V
CC
@ R ; measured at R , unloaded)
H W
L
INL
(Note 9)
Integral Non-linearity
Differential Non-linearity
Zero-scale Error
Monotonic over all tap positions, W and U
option
-1
LSB
(Note 5)
DNL
(Note 8)
Monotonic over all tap positions, W and U
option
-0.5
0.5
LSB
(Note 5)
ZSerror
(Note 6)
W option
U option
W option
U option
0
0
1
0.5
-1
5
2
0
0
LSB
(Note 5)
FSerror
(Note 7)
Full-scale Error
-5
-2
LSB
(Note 5)
-1
TC
Ratiometric Temperature Coefficient
DCP register set to 40 hex for W and U
option
±4
ppm/°C
V
(Note 10, 18)
FN6227 Rev 2.00
September 9, 2009
Page 3 of 14
ISL22416
Analog Specifications Over recommended operating conditions, unless otherwise stated. Parameters with MIN and/or MAX limits are
100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not
production tested. (Continued)
TYP
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 4)
MAX
UNIT
RESISTOR MODE (Measurements between R and R with R not connected, or between R and R with R not connected)
W
L
H
W
H
L
RINL
(Note 14)
Integral Non-linearity
DCP register set between 10 hex and 7F
hex; monotonic over all tap positions;
W and U option
-1
-1
1
MI
(Note 11)
RDNL
(Note 13)
Differential Non-linearity
W option
U option
W option
U option
1
0.5
5
MI
(Note 11)
-0.5
0
MI
(Note 11)
Roffset
(Note 12)
Offset
1
MI
(Note 11)
0
0.5
2
MI
(Note 11)
Operating Specifications Over the recommended operating conditions, unless otherwise specified. Parameters with MIN and/or MAX
limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
TYP
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 4)
MAX
UNIT
I
V
Supply Current (Volatile
f = 5MHz; (for SPI Active, Read and
SCK
0.5
mA
CC1
CC
Write/Read)
Volatile Write states only)
I
V
Supply Current (Non-volatile
f
= 5MHz; (for SPI Active, Read and
3
5
7
3
5
3
5
2
4
1
mA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µs
CC2
CC
Write/Read)
SCK
Non-volatile Write states only)
I
V
Current (Standby)
V
= +5.5V @ +85°C, SPI interface in
SB
CC
CC
standby state
V
= +5.5V @ +125°C, SPI interface in
CC
standby state
V
= +3.6V @ +85°C, SPI interface in
CC
standby state
V
= +3.6V @ +125°C, SPI interface in
CC
standby state
I
V
Current (Shutdown)
V
= +5.5V @ +85°C, SPI interface in
SD
CC
CC
standby state
V
= +5.5V @ +125°C, SPI interface in
CC
standby state
V
= +3.6V @ +85°C, SPI interface in
CC
standby state
V
= +3.6V @ +125°C, SPI interface in
CC
standby state
I
Leakage Current, at Pins SHDN, SCK, Voltage at pin from GND to V
SDI, SDO and CS
-1
LkgDig
CC,
SDO is inactive
t
Wiper Response Time
Wiper Response Time after SPI write to WR
register
1.5
1.5
1.5
WRT
(Note 18)
t
DCP Recall Time from Shutdown
From rising edge of SHDN signal to wiper
stored position and RH connection
µs
ShdnRec
(Note 18) Mode
SCK rising edge of last bit of ACR data byte
to wiper stored position and RH connection
µs
V
Power-on Recall Voltage
Ramp Rate
Minimum V
at which memory recall occurs
CC
2.0
0.2
2.6
V
POR
V
Ramp
V
V/ms
CC
CC
FN6227 Rev 2.00
September 9, 2009
Page 4 of 14
ISL22416
Operating Specifications Over the recommended operating conditions, unless otherwise specified. Parameters with MIN and/or MAX
limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested. (Continued)
TYP
SYMBOL
PARAMETER
Power-up Delay
TEST CONDITIONS
above V , to DCP Initial Value
MIN
(Note 4)
MAX
UNIT
t
V
3
ms
D
CC
POR
Register recall completed, and SPI Interface
in standby state
EEPROM SPECIFICATION
EEPROM Endurance
1,000,000
50
Cycles
Years
ms
EEPROM Retention
Temperature T +55°C
t
Non-volatile Write Cycle Time
12
20
WC
(Note 16)
SERIAL INTERFACE SPECIFICATIONS
V
SHDN, SCK, SDI, and CS Input Buffer
LOW Voltage
-0.3
0.3*V
CC
V
V
V
IL
V
SHDN, SCK, SDI, and CS Input Buffer
HIGH Voltage
0.7*V
V
+ 0.3
CC
IH
CC
Hysteresis SHDN, SCK, SDI, and CS Input Buffer
Hysteresis
0.05*
V
CC
V
SDO Output Buffer LOW Voltage
SDO Pull-up Resistor Off-chip
I
= 4mA
0
0.4
V
OL
OL
R
Maximum is determined by t
and t with
FO
2
10
5
k
pu
RO
maximum bus load Cb = 30pF, f
(Note 17)
= 5MHz
SCK
Cpin
SHDN, SCK, SDI, SDO and CS Pin
pF
(Note 18) Capacitance
f
SPI Frequency
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
SCK
t
SPI Clock Cycle Time
SPI Clock High Time
200
100
100
250
250
50
CYC
t
WH
t
SPI Clock Low Time
WL
t
Lead Time
LEAD
t
Lag Time
LAG
t
SDI, SCK and CS Input Setup Time
SDI, SCK and CS Input Hold Time
SDI, SCK and CS Input Rise Time
SDI, SCK and CS Input Fall Time
SDO Output Disable Time
SDO Output Valid Time
SDO Output Hold Time
SDO Output Rise Time
SDO Output Fall Time
CS Deselect Time
SU
t
50
H
t
10
RI
t
10
20
FI
t
0
100
350
DIS
t
V
t
0
2
HO
RO
t
R
R
= 2k, Cbus = 30pF
= 2k, Cbus = 30pF
60
60
pu
t
t
FO
CS
pu
NOTES:
4. Typical values are for T = +25°C and 3.3V supply voltage.
A
5. LSB: [V(R
)
– V(R ) ]/127. V(R
)
and V(R ) are V(R ) for the DCP register set to 7F hex and 00 hex respectively. LSB is the
W 0
W 127
W 0 W 127
W
incremental voltage when changing from one tap to an adjacent tap.
6. ZS error = V(RW) /LSB.
0
7. FS error = [V(RW)
– V ]/LSB.
CC
127
FN6227 Rev 2.00
Page 5 of 14
September 9, 2009
ISL22416
NOTES: (Continued)
8. DNL = [V(RW) – V(RW) ]/LSB-1, for i = 1 to 127. i is the DCP register setting.
i-1
i
9. INL = [V(RW) – (i • LSB) – V(RW) ]/LSB for i = 1 to 127
i
0
MaxVRW – MinVRW
6
10
i
i
10.
--------------------------------------------------------------------------------------------- -------------------- for i = 16 to 127 decimal, T = -40°C to 125°C. Max( ) is the maximum value of the wiper
TC
=
V
MaxVRW + MinVRW 2 +165°C
i
i
voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range.
and RW are the measured resistances for the DCP register set to 7F hex and
11. MI = |RW
– RW |/127. MI is a minimum increment. RW
127
127
0
0
00 hex respectively.
12. Roffset = RW /MI, when measuring between RW and RL.
0
Roffset = RW
/MI, when measuring between RW and RH.
127
13. RDNL = (RW – RW )/MI -1, for i = 1 to 127.
i-1
i
14. RINL = [RW – (MI • i) – RW ]/MI, for i = 1 to 127.
i
0
6
MaxRi – MinRi
10
15.
for i = 16 to 127, T = -40°C to 125°C. Max( ) is the maximum value of the resistance and Min ( ) is
the minimum value of the resistance over the temperature range.
--------------------------------------------------------------- ----------------
TC
=
R
165°C
MaxRi + MinRi 2
16. t
is the time from the end of a Write sequence of SPI serial interface, to the end of the self-timed internal non-volatile write cycle.
WC
17. R is specified for the highest data rate transfer for the device. Higher value pull-up can be used at lower data rates.
pu
18. Limits should be considered typical and are not production tested.
Timing Diagrams
Input Timing
t
CS
CS
t
t
t
LAG
LEAD
t
CYC
...
t
WH
SCK
SDI
t
t
t
RI
FI
t
WL
SU
H
...
MSB
LSB
HIGH IMPEDANCE
SDO
Output Timing
CS
SCK
SDO
...
...
t
t
t
DIS
V
HO
MSB
LSB
SDI
ADDR
FN6227 Rev 2.00
September 9, 2009
Page 6 of 14
ISL22416
XDCP Timing (for All Load Instructions)
CS
t
WC
SCK
...
...
t
WRT
MSB
LSB
SDI
V
W
HIGH IMPEDANCE
SDO
Typical Performance Curves
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
100
V
CC
= 3.3V, T = +125°C
90
80
70
60
50
40
30
20
10
0
T = +125°C
T = +25°C
V
= 3.3V, T = -40°C
V
CC
= 3.3V, T = +20°C
CC
2.7
3.2
3.7
4.2
(V)
4.7
CC
5.2
0
20
40
60
80
100
120
TAP POSITION (DECIMAL)
V
CC
FIGURE 1. WIPER RESISTANCE vs TAP POSITION
[ I(RW) = V /R ] FOR 10k (W)
FIGURE 2. STANDBY I
vs V
CC
CC TOTAL
0.2
0.1
0
0.2
0.1
0
T = +25°C
T = +25°C
V
= 2.7V
CC
V
= 2.7V
CC
-0.1
-0.2
-0.1
-0.2
V
= 5.5V
40
V
= 5.5V
CC
CC
0
20
40
60
80
100
120
0
20
60
80
100
120
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER
FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER
MODE FOR 10k (W)
MODE FOR 10k (W)
FN6227 Rev 2.00
September 9, 2009
Page 7 of 14
ISL22416
Typical Performance Curves (Continued)
1.3
10k
1.1
0.0
-0.3
-0.6
-0.9
-1.2
-1.5
V
= 2.7V
CC
0.9
0.7
V
= 5.5V
CC
50k
V
= 2.7V
CC
0.5
0.3
V
= 5.5V
CC
10k
40
0.1
50k
-0.1
-0.3
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (ºC)
FIGURE 5. ZS
vs TEMPERATURE
FIGURE 6. FS
vs TEMPERATURE
ERROR
ERROR
0.4
0.2
0
0.4
0.2
0
T = +25°C
T = +25°C
V
= 5.5V
V
= 5.5V
CC
CC
-0.2
-0.4
-0.6
-0.2
-0.4
-0.6
V
= 2.7V
CC
V
= 2.7V
CC
16
36
56
76
96
116
16
36
56
76
96
116
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 7. DNL vs TAP POSITION IN RHEOSTAT MODE FOR
FIGURE 8. INL vs TAP POSITION IN RHEOSTAT MODE FOR
10k (W)
10k (W)
1.0
0.5
105
90
75
60
45
V
= 2.7V
CC
50k
0.0
-0.5
-1.0
V
= 5.5V
CC
10k
50k
30
15
0
10k
16
36
56
76
96
-40
-20
0
20
40
60
80
100
120
TEMPERATURE (ºC)
TAP POSITION (DECIMAL)
FIGURE 9. END TO END R
% CHANGE vs
FIGURE 10. TC FOR VOLTAGE DIVIDER MODE IN ppm
TOTAL
TEMPERATURE
FN6227 Rev 2.00
September 9, 2009
Page 8 of 14
ISL22416
Typical Performance Curves (Continued)
OUTPUT
INPUT
300
250
200
150
100
50k
10k
WIPER AT MID POINT (POSITION 40h)
= 9.5k
R
TOTAL
50
0
16
36
56
76
96
TAP POSITION (DECIMAL)
FIGURE 11. TC FOR RHEOSTAT MODE IN ppm
FIGURE 12. FREQUENCY RESPONSE (2.6MHz)
SCL
SIGNAL AT WIPER
(WIPER UNLOADED)
SIGNAL AT WIPER
(WIPER UNLOADED MOVEMENT
FROM 7Fh TO 00h)
WIPER MID POINT MOVEMENT
FROM 3Fh TO 40h
FIGURE 13. MIDSCALE GLITCH, CODE 3Fh TO 40h
FIGURE 14. LARGE SIGNAL SETTLING TIME
to logic high, the previous latch settings put RW at the same
resistance setting prior to shutdown. This pin is logically
ANDed with SHDN bit in ACR register. SPI interface is still
available in shutdown mode and all registers are accessible.
This pin must remain HIGH for normal operation.
Pin Description
Potentiometer Pins
RH AND RL
The high (RH) and low (RL) terminals of the ISL22416 are
equivalent to the fixed terminals of a mechanical
RH
potentiometer. RH and RL are referenced to the relative
position of the wiper and not the voltage potential on the
terminals. With WR set to 127 decimal, the wiper will be closest
to RH, and with the WR set to 0, the wiper is closest to RL.
RW
RW
RL
RW is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WR register.
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
SHDN
The SHDN pin forces the resistor to end-to-end open circuit
condition on RH and shorts RW to RL. When SHDN is returned
FN6227 Rev 2.00
September 9, 2009
Page 9 of 14
ISL22416
monotonically from the position closest to RL to the closest to
RH. At the same time, the resistance between RW and RL
increases monotonically, while the resistance between RH and
RW decreases monotonically.
Bus Interface Pins
SERIAL CLOCK (SCK)
This is the serial clock input of the SPI serial interface.
SERIAL DATA OUTPUT (SDO)
While the ISL22416 is being powered up, the WR is reset to
40h (64 decimal), which locates RW roughly at the center
between RL and RH. After the power supply voltage becomes
large enough for reliable non-volatile memory reading, the WR
will be reload with the value stored in a non-volatile Initial Value
Register (IVR).
The SDO is an open drain serial data output pin. During a read
cycle, the data bits are shifted out at the falling edge of the
serial clock SCK, while the CS input is low.
SDO requires an external pull-up resistor for proper operation.
SERIAL DATA INPUT (SDI)
The WR and IVR can be read or written to directly using the
SPI serial interface as described in the following sections.
The SDI is the serial data input pin for the SPI interface. It
receives device address, operation code, wiper address and
data from the SPI external host device. The data bits are
shifted in at the rising edge of the serial clock SCK, while the
CS input is low.
Memory Description
The ISL22416 contains one non-volatile 7-bit register, known as
the Initial Value Register (IVR), volatile 7-bit Wiper Register
(WR), and volatile 8-bit Access Control Register (ACR). The
memory map is shown in Table 1. The non-volatile register (IVR)
at address 0, contain initial wiper position and volatile registers
(WR) contain current wiper position.
CHIP SELECT (CS)
CS LOW enables the ISL22416, placing it in the active power
mode. A HIGH to LOW transition on CS is required prior to the
start of any operation after power up. When CS is HIGH, the
ISL22416 is deselected and the SDO pin is at high impedance,
and (unless an internal write cycle is underway) the device will
be in the standby state.
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
2
1
0
—
ACR
Reserved
Principles of Operation
IVR
WR
The ISL22416 is an integrated circuit incorporating one DCP
with its associated registers, non-volatile memory and the SPI
serial interface providing direct communication between host
and potentiometer and memory. The resistor array is
The non-volatile IVR and volatile WR registers are accessible
with the same address.
comprised of individual resistors connected in series. At either
end of the array and between each resistor is an electronic
switch that transfers the potential at that point to the wiper.
The Access Control Register (ACR) contains information and
control bits described in Table 2.
The VOL bit (ACR<7>) determines whether the access is to
wiper registers WR or initial value registers IVR.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
TABLE 2. ACCESS CONTROL REGISTER (ACR)
When the device is powered down, the last value stored in IVR
will be maintained in the non-volatile memory. When power is
restored, the contents of the IVR is recalled and loaded into the
WR to set the wiper to the initial value.
BIT #
7
6
5
4
0
3
0
2
0
1
0
0
0
BIT NAME VOL SHDN WIP
If VOL bit is 0, the non-volatile IVR register is accessible. If
VOL bit is 1, only the volatile WR is accessible. Note, value is
written to IVR register also is written to the WR. The default
value of this bit is 0.
DCP Description
The DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each DCP
are equivalent to the fixed terminals of a mechanical
The SHDN bit (ACR<6>) disables or enables Shutdown mode.
This bit is logically ANDed with SHDN pin. When this bit is 0, DCP
is in Shutdown mode. Default value of SHDN bit is 1.
potentiometer (RH and RL pins). The RW pin of the DCP is
connected to intermediate nodes, and is equivalent to the wiper
terminal of a mechanical potentiometer. The position of the
wiper terminal within the DCP is controlled by a 7-bit volatile
Wiper Register (WR). When the WR of a DCP contains all
zeroes (WR<6:0>: 00h), its wiper terminal (RW) is closest to its
“Low” terminal (RL). When the WR register of a DCP contains all
ones (WR<6:0>: 7Fh), its wiper terminal (RW) is closest to its
“High” terminal (RH). As the value of the WR increases from all
zeroes (0) to all ones (127 decimal), the wiper moves
The WIP bit (ACR<5>) is read only bit. It indicates that
non-volatile write operation is in progress. The WIP bit can be
read repeatedly after a non-volatile write to determine if the write
has been completed. It is impossible to write to the WR or ACR
while WIP bit is 1.
FN6227 Rev 2.00
September 9, 2009
Page 10 of 14
ISL22416
operation by pulling the CS pin from LOW to HIGH. For a write
to address 0 (WR), the byte at address 2 (ACR<7>)
determines if the Data Byte is to be written to volatile or both
volatile and non-volatile registers. Refer to “Memory
Description” on page 10 and Figure 16.
Shutdown Mode
The device can be put in Shutdown mode either by pulling the
SHDN pin to GND or setting the SHDN bit in the ACR register to
0. The truth table for Shutdown mode is in Table 3.
TABLE 3. SHUTDOWN MODE
The internal non-volatile write cycle starts after rising edge of
CS and takes up to 20ms.
SHDN PIN
High
SHDN BIT
MODE
Normal operation
Shutdown
1
1
0
0
Read Operation
Low
A read operation to the ISL22416 is a three byte operation. It
requires first, the CS transition from HIGH to LOW, then a valid
Identification Byte, then a valid instruction byte followed by
“dummy” Data Byte is sent to SDI pin. The SPI host reads the
data from SDO pin on falling edge of SCK. The host terminates
the read operation by pulling the CS pin from LOW to HIGH
(see Figure 17).
High
Shutdown
Low
Shutdown
SPI Serial Interface
The ISL22416 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output with data
clocked in on the rising edge of SCK, and clocked out on the
falling edge of SCK. CS must be LOW during communication
with the ISL22416. SCK and CS lines are controlled by the
host or master. The ISL22416 operates only as a slave device.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit is
0. If the WIP bit (ACR[5]) is not 0, the host should repeat its
reading sequence again.
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Applications Information
Communicating with ISL22416
Protocol Conventions
Communication with ISL22416 proceeds using SPI interface
through the ACR (address 10b), IVR (address 00b) and WR
(address 00b) registers.
The first byte sent to the ISL22416 from the SPI host is the
Identification Byte. A valid Identification Byte contains 0101 as
the four MSBs, with the following four bits set to 0.
The wiper of the potentiometer is controlled by the WR register.
Writes and reads can be made directly to this register to control
and monitor the wiper position without any non-volatile
memory changes. This is done by setting MSB bit at address
10b to 1.
TABLE 4. IDENTIFICATION BYTE FORMAT
0
1
0
1
0
0
0
0
(MSB)
(LSB)
The next byte sent to the ISL22416 contains the instruction
and register pointer information. The four MSBs are the
instruction and two LSBs are register address (see Table 5).
The non-volatile IVR stores the power up value of the wiper.
IVR is accessible when MSB bit at address 10b is set to 0.
Writing a new value to the IVR register will set a new power up
position for the wiper. Also, writing to this register will load the
same value into the WR as the IVR. Reading from the IVR will
not change the WR, if its contents are different.
TABLE 5. IDENTIFICATION BYTE FORMAT
7
6
5
4
3
0
2
0
1
0
I3
I2
I1
I0
R1
R0
There are only two valid instruction sets:
1011(binary) - is a Read operation
1100(binary) - is a Write operation
There are only two registers address possible for this DCP. If the
R1, R0 bits are zero, then the read or write is to either the IVR or
the WR register (depends of VOL bit at ACR). If the R1 bit is 1
and R0 bit is 0, then the operation is on the ACR.
Write Operation
A Write operation to the ISL22416 is a three-byte operation. It
requires first, the CS transition from HIGH to LOW, then a valid
Identification Byte, then a valid instruction byte followed by
Data Byte is sent to SDI pin. The host terminates the write
FN6227 Rev 2.00
September 9, 2009
Page 11 of 14
ISL22416
CS
SCK
SDI
0
0
0
1
0
1
0
0
0
I3 I2
I1 I0
0
0
R1 R0
0
D6 D5 D4 D3 D2 D1 D0
FIGURE 16. THREE BYTE WRITE SEQUENCE
CS
SCK
SDI
DON’T CARE
0
0
0
0
1
0
1
0
0
I3 I2
I1 I0
0
0
R1 R0
SDO
0
D6 D5 D4 D3 D2 D1 D0
FIGURE 17. THREE BYTE READ SEQUENCE
B. Reading from the WR
Examples
This sequence will read the value from the WR (volatile):
A. Writing to the IVR
Write to ACR first to access the WR
This sequence will write a new value (77h) to the IVR
(non-volatile):
Send the ID byte, Instruction Byte, then the Data byte
Set the ACR (Addr 02h) for NV write (40h)
0 1 0 1 0 0 0 0 1 1 0 0 0 0 1 0 1 1 0 0 0 0 0 0
Send the ID byte, Instruction Byte, then the Data byte
(Sent to DI)
0 1 0 1 0 0 0 0 1 1 0 0 0 0 1 0 0 1 0 0 0 0 0 0
Read the data from WR (Addr 00h)
(Sent to DI)
Send the ID byte, Instruction Byte, then Read the Data byte
Set the IVR (Addr 00h) to 77h
0 1 0 1 0 0 0 0 1 0 1 1 0 0 0 0 x x x x x x x x
Send the ID byte, Instruction Byte, then the Data byte
(Out on DO)
0 1 0 1 0 0 0 0 1 1 0 0 0 0 0 0 0 1 1 1 0 1 1 1
(Sent to DI)
FN6227 Rev 2.00
September 9, 2009
Page 12 of 14
ISL22416
Mini Small Outline Plastic Packages (MSOP)
N
M10.118 (JEDEC MO-187BA)
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
E1
E
INCHES
MILLIMETERS
SYMBOL
MIN
MAX
MIN
0.94
0.05
0.75
0.18
0.09
2.95
2.95
MAX
1.10
0.15
0.95
0.27
0.20
3.05
3.05
NOTES
-B-
0.20 (0.008)
INDEX
AREA
A
A1
A2
b
0.037
0.002
0.030
0.007
0.004
0.116
0.116
0.043
0.006
0.037
0.011
0.008
0.120
0.120
-
1 2
A
B
C
-
TOP VIEW
-
4X
0.25
(0.010)
R1
9
R
GAUGE
PLANE
c
-
D
3
SEATING
PLANE
E1
e
4
L
-C-
4X
0.020 BSC
0.50 BSC
-
L1
A
A2
E
0.187
0.016
0.199
0.028
4.75
0.40
5.05
0.70
-
SEATING
PLANE
L
6
0.10 (0.004)
-A-
C
C
L1
N
0.037 REF
10
0.95 REF
10
-
b
-H-
A1
7
e
D
R
0.003
0.003
-
-
0.07
0.07
-
-
-
0.20 (0.008)
C
R1
-
a
SIDE VIEW
o
o
o
o
C
L
5
15
5
15
-
o
o
o
o
E
1
0
6
0
6
-
-B-
0.20 (0.008)
C
D
END VIEW
Rev. 0 12/02
NOTES:
1. These package dimensions are within allowable dimensions of
JEDEC MO-187BA.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs and are measured at Datum Plane. Mold flash, protrusion
and gate burrs shall not exceed 0.15mm (0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions
- H -
and are measured at Datum Plane.
Interlead flash and
protrusions shall not exceed 0.15mm (0.006 inch) per side.
5. Formed leads shall be planar with respect to one another within
0.10mm (.004) at seating Plane.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.08mm (0.003 inch) total in excess
of “b” dimension at maximum material condition. Minimum space
between protrusion and adjacent lead is 0.07mm (0.0027 inch).
- B -
-A -
10. Datums
and
to be determined at Datum plane
.
- H -
11. Controlling dimension: MILLIMETER. Converted inch dimen-
sions are for reference only
FN6227 Rev 2.00
September 9, 2009
Page 13 of 14
ISL22416
Thin Dual Flat No-Lead Plastic Package (TDFN)
2X
L10.3x3B
0.15 C
A
10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
A
D
2X
MILLIMETERS
0.15
C B
SYMBOL
MIN
0.70
-
NOMINAL
0.75
MAX
0.80
0.05
NOTES
A
A1
A3
b
-
-
-
E
0.20 REF
0.25
-
6
INDEX
AREA
0.18
2.23
1.49
0.30
2.48
1.74
5, 8
D
3.00 BSC
2.38
-
TOP VIEW
B
A
D2
E
7, 8
3.00 BSC
1.64
-
// 0.10
0.08
C
E2
e
7, 8
0.50 BSC
-
-
C
k
0.20
0.30
-
-
A3
C
SIDE VIEW
L
0.40
0.50
8
SEATING
PLANE
N
10
2
D2
D2/2
2
7
8
Nd
5
3
(DATUM B)
Rev. 0 2/06
NOTES:
1
6
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
INDEX
AREA
NX k
E2
3. Nd refers to the number of terminals on D.
(DATUM A)
4. All dimensions are in millimeters. Angles are in degrees.
E2/2
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
NX L
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
N
N-1
NX b
8
e
5
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
(Nd-1)Xe
REF.
M
0.10
C A B
BOTTOM VIEW
8. Nominal dimensions are provided to assist with PCB Land
Pattern Design efforts, see Intersil Technical Brief TB389.
C
9. COMPLIANT TO JEDEC MO-229-WEED-3 except for
dimensions E2 & D2.
L
(A1)
NX (b)
L
9
5
e
SECTION "C-C"
TERMINAL TIP
C C
FOR ODD TERMINAL/SIDE
© Copyright Intersil Americas LLC 2006-2009. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6227 Rev 2.00
September 9, 2009
Page 14 of 14
相关型号:
ISL22419
Single Digitally Controlled Potentiometer(XDCP) Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only
INTERSIL
ISL22419UFU8Z
Single Digitally Controlled Potentiometer(XDCP) Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only
INTERSIL
ISL22419WFU8Z
Single Digitally Controlled Potentiometer(XDCP) Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only
INTERSIL
ISL22424TFR16Z
Dual Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, SPI® Bus, 256 Taps; QFN16, TSSOP14; Temp Range: -40° to 125°C
RENESAS
ISL22424TFR16Z-TK
Dual Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, SPI® Bus, 256 Taps; QFN16, TSSOP14; Temp Range: -40° to 125°C
RENESAS
ISL22424TFV14Z-TK
Dual Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, SPI® Bus, 256 Taps; QFN16, TSSOP14; Temp Range: -40° to 125°C
RENESAS
ISL22424UFR16Z
Dual Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, SPI® Bus, 256 Taps; QFN16, TSSOP14; Temp Range: -40° to 125°C
RENESAS
ISL22424UFR16Z-TK
Dual Digitally Controlled Potentiometer (XDCP™), Low Noise, Low Power, SPI® Bus, 256 Taps; QFN16, TSSOP14; Temp Range: -40° to 125°C
RENESAS
©2020 ICPDF网 联系我们和版权申明