ISL23418UFUZ-T [RENESAS]
50K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 128 POSITIONS, PDSO10, ROHS COMPLIANT, PLASTIC, MO-187BA, MSOP-10;型号: | ISL23418UFUZ-T |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | 50K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 128 POSITIONS, PDSO10, ROHS COMPLIANT, PLASTIC, MO-187BA, MSOP-10 光电二极管 转换器 电阻器 |
文件: | 总20页 (文件大小:923K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Single, 128-Tap, Low Voltage Digitally Controlled
Potentiometer (XDCP™)
ISL23418
The ISL23418 is a volatile, low voltage, low noise, low power,
SPI™ bus, 128 taps, single digitally controlled potentiometer
(DCP), which integrates DCP core, wiper switches, and control
logic on a monolithic CMOS integrated circuit.
Features
• 128 Resistor Taps
• SPI Serial Interface
- No Additional Level Translator for Low Bus Supply
- Daisy Chaining of Multiple DCP
The digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wiper is controlled by the user through the SPI
bus interface. The potentiometer has an associated volatile
Wiper Register (WR) that can be directly written to and read by
the user. The contents of the WR controls the position of the
wiper. When powered on, the ISL23418 wiper always
commences at mid-scale (64-tap position).
• Wiper Resistance: 70Ω Typical @ V = 3.3V
CC
• Shutdown Mode: Forces DCP into End-to-end Open Circuit;
RW Shorted to RL Internally
• Power-on Preset to Mid-scale (64-tap Position)
• Shutdown and Standby Current <2.8µA Max
• Power Supply
- V = 1.7V to 5.5V Analog Power Supply
CC
The low voltage, low power consumption, and small package
size of the ISL23418 make it an ideal choice for use in battery
- V
LOGIC
= 1.2V to 5.5V SPI Bus/Logic Power Supply
operated equipment. The ISL23418 has a V
down to 1.2V bus operation, independent from the V value.
pin allowing
LOGIC
• DCP Terminal Voltage from 0V to V
CC
CC
• 10kΩ, 50kΩ or 100kΩ Total Resistance
• Extended Industrial Temperature Range: -40°C to +125°C
• 10 Ld MSOP or 10 Ld µTQFN Packages
• Pb-free (RoHS compliant)
This allows for low logic levels to be connected directly to the
ISL23418 without passing through a voltage level shifter.
The DCP can be used as a three-terminal potentiometer or as a
two-terminal variable resistor in a wide variety of applications
including control, parameter adjustments, and signal
processing.
Applications
• Power Supply Margining
Related Literature
• See ISL23415, “Single, Low Voltage Digitally Controlled
Potentiometer (XDCP™)”
• RF Power Amplifier Bias Compensation
• LCD Bias Compensation
• Gain Adjustment in Battery Powered Instruments
• Portable Medical Equipment Calibration
10000
8000
6000
4000
2000
0
VREF
RH1
-
VREF_M
RW1
ISL23418
+
ISL28114
RL1
0
25
50
75
100
125
TAP POSITION (DECIMAL)
FIGURE 1. FORWARD AND BACKWARD RESISTANCE vs TAP
POSITION, 10k
FIGURE 2. V
ADJUSTMENT
REF
August 3, 2011
FN7901.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
XDCP is a trademark of Intersil Americas Inc. Intersil (and design) is a trademark owned by Intersil Corporation
or one of its subsidiaries .All other trademarks mentioned are the property of their respective owners.
1
ISL23418
Block Diagram
V
V
CC
LOGIC
RH
SCK
SDI
POWER-UP
INTERFACE,
CONTROL
AND
STATUS
LOGIC
I/O BLOCK
LEVEL
SHIFTER
WR
SDO
CS
VOLATILE
REGISTER
AND
WIPER
CONTROL
CIRCUITRY
RL
RW
GND
Pin Configurations
Pin Description
ISL23418
(10 LD MSOP)
TOP VIEW
MSOP
µTQFN
SYMBOL
DESCRIPTION
1
10
V
SPI bus/logic supply; range 1.2V to
5.5V
LOGIC
O
10
GND
V
1
2
3
4
5
LOGIC
SCK
2
3
1
2
SCK
SDO
Logic pin: serial bus clock input
V
9
CC
Logic pin: serial bus data output
(configurable)
RH
SDO
SDI
CS
8
7
RW
RL
4
5
6
7
8
9
3
4
5
6
7
8
SDI
CS
Logic pin: serial bus data input
Logic pin: active low Chip Select
DCP “low” terminal
6
RL
ISL23418
(10 LD µTQFN)
TOP VIEW
RW
RH
DCP wiper terminal
DCP “high” terminal
V
Analog power supply; range 1.7V to
5.5V
CC
O
SCK
1
9
8
7
6
GND
10
9
GND
Ground pin
SDO
SDI
CS
2
3
4
V
CC
RH
RW
FN7901.0
August 3, 2011
2
ISL23418
Ordering Information
RESISTANCE
PART NUMBER
(Note 5)
PART
MARKING
OPTION
(kΩ)
TEMP. RANGE
PACKAGE
(Pb-free)
PKG.
DWG. #
(°C)
ISL23418TFUZ (Notes 1, 3)
ISL23418UFUZ (Notes 1, 3)
ISL23418WFUZ (Notes 1, 3)
ISL23418TFRUZ-T7A (Notes 2, 4)
ISL23418TFRUZ-TK (Notes 2, 4)
ISL23418UFRUZ-T7A (Notes 2, 4)
ISL23418UFRUZ-TK (Notes 2, 4)
ISL23418WFRUZ-T7A (Notes 2, 4)
ISL23418WFRUZ-TK (Notes 2, 4)
NOTES:
3418T
3418U
100
50
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
10 Ld MSOP
M10.118
10 Ld MSOP
M10.118
3418W
HL
10
10 Ld MSOP
M10.118
100
100
50
10 Ld 2.1x1.6 µTQFN
10 Ld 2.1x1.6 µTQFN
10 Ld 2.1x1.6 µTQFN
10 Ld 2.1x1.6 µTQFN
10 Ld 2.1x1.6 µTQFN
10 Ld 2.1x1.6 µTQFN
L10.2.1x1.6A
L10.2.1x1.6A
L10.2.1x1.6A
L10.2.1x1.6A
L10.2.1x1.6A
L10.2.1x1.6A
HL
HK
HK
50
HJ
10
HJ
10
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. Please refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
4. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate -
e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
5. For Moisture Sensitivity Level (MSL), please see device information page for ISL23418. For more information on MSL please see Tech Brief TB363.
FN7901.0
August 3, 2011
3
ISL23418
Absolute Maximum Ratings
Thermal Information
Supply Voltage Range
Thermal Resistance (Typical)
10 Ld MSOP Package (Notes 6, 7). . . . . . .
10 Ld µTQFN Package (Notes 6, 7) . . . . . .
θ
JA (°C/W)
170
θ
JC (°C/W)
V
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
70
90
CC
LOGIC
145
Voltage on any DCP Terminal Pin . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
Voltage on any Digital Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
Wiper Current I (10s). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
W
ESD Rating
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Human Body Model (Tested per JESD22-A114E). . . . . . . . . . . . . . .6.5kV
CDM Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . . . . . . . . 1kV
Machine Model (Tested per JESD22-A115-A). . . . . . . . . . . . . . . . . . 200V
Latch Up
Recommended Operating Conditions
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
(Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . 100mA @ +125°C
V
V
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7V to 5.5V
CC
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2V to 5.5V
LOGIC
DCP Terminal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to V
CC
Max Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
6. θ is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
JA
7. For θ , the “case temp” location is taken at the package top center.
JC
Analog Specifications
V
= 2.7V to 5.5V, V
= 1.2V to 5.5V over recommended operating conditions unless otherwise stated.
LOGIC
CC
Boldface limits apply over the operating temperature range, -40°C to +125°C.
MIN
TYP
MAX
SYMBOL
PARAMETER
to R Resistance
TEST CONDITIONS
(Note 20)
(Note 8)
(Note 20)
UNITS
R
R
W option
U option
T option
10
50
kΩ
TOTAL
H
L
kΩ
kΩ
100
±2
R
to R Resistance Tolerance
-20
+20
%
H
L
End-to-End Temperature Coefficient
W option
U option
T option
175
85
ppm/°C
ppm/°C
ppm/°C
V
70
V
, V
RH RL
DCP Terminal Voltage
Wiper Resistance
V
or V to GND
RL
0
V
CC
RH
R
RH - floating, V = 0V, force I current
RL
70
200
Ω
W
W
to the wiper, I = (V - V )/R
W
CC RL
TOTAL,
V
= 2.7V to 5.5V
CC
V
= 1.7V
580
32/32/32
<0.1
16
Ω
CC
C /C /C
W
Terminal Capacitance
Leakage on DCP Pins
Resistor Noise Density
See “DCP Macro Model” on page 8.
Voltage at pin from GND to V
pF
µA
H
L
I
-0.4
0.4
LkgDCP
Noise
CC
Wiper at middle point, W option
Wiper at middle point, U option
Wiper at middle point, T option
nV/ Hz
√
49
nV/ Hz
√
61
nV/ Hz
√
Feed Thru Digital Feedthrough from Bus to Wiper Wiper at middle point
-65
dB
dB
PSRR
Power Supply Reject Ratio
Wiper output change if V change
CC
-75
±10%; wiper at middle point
VOLTAGE DIVIDER MODE (0V @ RL; V @ RH; measured at RW, unloaded)
CC
INL
Integral Non-linearity, Guaranteed
W, U, T option
-0.5
±0.15
+0.5
LSB
(Note 13) Monotonic
(Note 9)
FN7901.0
August 3, 2011
4
ISL23418
Analog Specifications
V
= 2.7V to 5.5V, V
= 1.2V to 5.5V over recommended operating conditions unless otherwise stated.
LOGIC
CC
Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
MIN
TYP
MAX
SYMBOL
DNL
PARAMETER
TEST CONDITIONS
(Note 20)
(Note 8)
(Note 20)
UNITS
Differential Non-linearity, Guaranteed W, U, T option
-0.5
-2.5
-1.0
0
±0.15
-1.5
-0.7
+0.5
LSB
(Note 9)
(Note 12) Monotonic
FSerror
(Note 11)
Full-scale Error
W option
U, T option
W option
U, T option
0
LSB
(Note 9)
0
LSB
(Note 9)
ZSerror
(Note 10)
Zero-scale Error
-1.5
-0.7
2.5
1.0
LSB
(Note 9)
0
LSB
(Note 9)
TC
(Note 14)
Ratiometric Temperature Coefficient
W option, Wiper Register set to 40 hex
U option, Wiper Register set to 40 hex
T option, Wiper Register set to 40 hex
From code 0 to 7F hex
8
4
ppm/°C
ppm/°C
ppm/°C
ns
V
2.3
t
Large Signal Wiper Settling Time
-3dB Cutoff Frequency
300
1200
250
120
LS_Settling
f
Wiper at middle point W option
Wiper at middle point U option
Wiper at middle point T option
kHz
cutoff
kHz
kHz
RHEOSTAT MODE (Measurements between RW and RL pins with RH not connected, or between RW and RH with RL not connected)
Integral Non-linearity, Guaranteed W option; V = 2.7V to 5.5V
R
-1.0
-0.5
-0.5
-0.5
0
±0.5
±3.0
±0.15
±1.0
±0.15
±0.4
±0.15
±0.4
1.8
+1.0
+0.5
+0.5
+0.5
3.0
MI
INL
CC
(Note 18) Monotonic
(Note 15)
W option; V = 1.7V
CC
MI
(Note 15)
U, T option; V = 2.7V to 5.5V
CC
MI
(Note 15)
U, T option; V = 1.7V
CC
MI
(Note 15)
R
Differential Non-linearity, Guaranteed W option; V = 2.7V to 5.5V
CC
MI
(Note 15)
DNL
(Note 17) Monotonic
W option; V = 1.7V
CC
MI
(Note 15)
U, T option; V = 2.7V to 5.5V
CC
MI
(Note 15)
U, T option; V = 1.7V
CC
MI
(Note 15)
R
Offset, Wiper at 0 Position
W option; V = 2.7V to 5.5V
CC
MI
(Note 15)
offset
(Note 16)
W option; V = 1.7V
CC
3.0
MI
(Note 15)
U, T option; V = 2.7V to 5.5V
CC
0
0.3
1
MI
(Note 15)
U, T option; V = 1.7V
CC
0.5
MI
(Note 15)
FN7901.0
August 3, 2011
5
ISL23418
Analog Specifications
V
= 2.7V to 5.5V, V
= 1.2V to 5.5V over recommended operating conditions unless otherwise stated.
LOGIC
CC
Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
MIN
TYP
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
(Note 20)
(Note 8)
(Note 20)
UNITS
TCR
(Note 19)
Resistance Temperature Coefficient
W option; Wiper register set between
32 hex and 7F hex
220
100
75
ppm/°C
U option; Wiper register set between
32 hex and 7F hex
ppm/°C
ppm/°C
T option; Wiper register set between
32 hex and 7F hex
Operating Specifications
V
= 2.7V to 5.5V, V
= 1.2V to 5.5V over recommended operating conditions unless otherwise
CC
LOGIC
stated. Boldface limits apply over the operating temperature range, -40°C to +125°C.
MIN
TYP
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
(Note 20)
(Note 8)
(Note 20)
UNITS
mA
I
V
Supply Current (Write/Read)
V
= 5.5V, V = 5.5V,
1.5
LOGIC
LOGIC
LOGIC
CC
f
= 5MHz (for SPI active read and write)
SCK
V
= 1.2V, V = 1.7V,
CC
30
µA
LOGIC
= 1MHz (for SPI active read and write)
f
SCK
I
V
V
Supply Current (Write/Read)
V
V
V
= 5.5V, V = 5.5V
CC
100
10
µA
µA
µA
CC
CC
LOGIC
LOGIC
LOGIC
= 1.2V, V = 1.7V
CC
I
Standby Current
= V = 5.5V,
CC
1.3
LOGIC SB
LOGIC
SPI interface in standby
V
= 1.2V, V = 1.7V,
0.4
1.5
1
µA
µA
µA
µA
µA
µA
µA
µA
µs
LOGIC
CC
SPI interface in standby
I
V
Standby Current
V = V = 5.5V,
LOGIC CC
SPI interface in standby
CC SB
CC
V
= 1.2V, V = 1.7V,
LOGIC
CC
SPI interface in standby
I
V
Shutdown Current
V
= V = 5.5V,
LOGIC CC
1.3
0.4
1.5
1
LOGIC SHDN LOGIC
SPI interface in standby
V
= 1.2V, V = 1.7V,
LOGIC
CC
SPI interface in standby
I
V
Shutdown Current
V = V = 5.5V,
LOGIC CC
SPI interface in standby
CC SHDN
CC
V
= 1.2V, V = 1.7V,
LOGIC
CC
SPI interface in standby
I
Leakage Current, at Pins CS, SDO, SDI,
SCK
Voltage at pin from GND to V
-0.4
<0.1
0.4
1.5
3.5
1.5
0.4
LkgDig
LOGIC
t
Wiper Response Time
W option; CS rising edge to wiper new position,
from 10% to 90% of final value.
DCP
U option; CS rising edge to wiper new position,
from 10% to 90% of final value.
µs
T option; CS rising edge to wiper new position,
from 10% to 90% of final value.
µs
tShdnRec DCP Recall Time from Shutdown Mode CS rising edge to wiper recalled position and
RH connection
µs
V
, V
V
, V
Ramp Rate
Ramp monotonic at any level
0.01
50
V/ms
CC LOGIC CC LOGIC
Ramp
FN7901.0
August 3, 2011
6
ISL23418
Serial Interface Specification For SCK, SDI, SDO, CS, unless otherwise noted.
MIN
TYP
MAX
SYMBOL
PARAMETER
Input LOW Voltage
TEST CONDITIONS
(Note 20)
(Note 8)
(Note 20)
UNITS
V
-0.3
0.3 x V
V
V
V
IL
LOGIC
V
Input HIGH Voltage
0.7 x V
V
LOGIC
+ 0.3
IH
LOGIC
Hysteresis
SDI and SCK Input Buffer Hysteresis
V
V
> 2V
< 2V
0.05 x V
LOGIC
LOGIC
0.1 x V
0
LOGIC
LOGIC
V
SDO Output Buffer LOW Voltage
SDO Pull-up Resistor Off-chip
I
I
= 3mA, V
> 2V
0.4
V
V
OL
OL
OL
LOGIC
= 1.5mA, V
< 2V
0.2 x V
LOGIC
LOGIC
R
Maximum is determined by t and t with
1.5
kΩ
pu
RO
FO
maximum bus load Cb = 30pF, f
= 5MHz
SCK
C
SCK, SDO, SDI, CS Pin Capacitance
SCK Frequency
10
pF
MHz
MHz
ns
pin
f
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
= 1.7V to 5.5V
= 1.2V to 1.6V
≥ 1.7V
5
1
SCK
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
LOGIC
t
SPI Clock Cycle Time
200
CYC
t
SPI Clock High Time
≥ 1.7V
100
100
250
250
50
ns
WH
t
SPI Clock Low Time
≥ 1.7V
ns
WL
t
Lead Time
≥ 1.7V
ns
LEAD
t
Lag Time
≥ 1.7V
ns
LAG
t
SDI, SCK and CS Input Setup Time
SDI, SCK and CS Input Hold Time
SDI, SCK and CS Input Rise Time
SDI, SCK and CS Input Fall Time
SDO Output Disable Time
SDO Output Setup Time
SDO Output Valid Time
SDO Output Hold Time
SDO Output Rise Time
SDO Output Fall Time
CS Deselect Time
≥ 1.7V
ns
SU
t
≥ 1.7V
50
ns
H
t
≥ 1.7V
10
ns
RI
t
≥ 1.7V
10
20
ns
FI
t
≥ 1.7V
0
100
ns
DIS
t
≥ 1.7V
50
ns
SO
t
≥ 1.7V
150
0
ns
V
t
≥ 1.7V
ns
HO
RO
t
R
= 1.5k, Cbus = 30pF
= 1.5k, Cbus = 30pF
60
60
ns
pu
pu
t
t
R
ns
FO
CS
2
µs
NOTES:
8. Typical values are for T = +25°C and 3.3V supply voltages.
A
9. LSB = [V(RW)
127
– V(RW) ]/127. V(RW) and V(RW) are V(RW) for the DCP register set to 7F hex and 00 hex, respectively. LSB is the incremental
0
127 0
voltage when changing from one tap to an adjacent tap.
10. ZS error = V(RW) /LSB.
0
11. FS error = [V(RW)
127
– V ]/LSB.
CC
12. DNL = [V(RW) – V(RW) ]/LSB-1, for i = 1 to 127. i is the DCP register setting.
i-1
i
13. INL = [V(RW) – i • LSB – V(RW) ]/LSB for i = 1 to 127
i
0
Max(V(RW) ) – Min(V(RW) )
6
10
14.
i
i
for i = 16 to 127 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper voltage
and Min( ) is the minimum value of the wiper voltage over the temperature range.
----------------------------------------------------------------------------- ---------------------
TC
=
×
V
V(RWi(+25°C))
+165°C
15. MI = |RW
– RW |/127. MI is a minimum increment. RW and RW are the measured resistances for the DCP register set to 7F hex and 00
127 0
127
hex, respectively.
0
16. Roffset = RW /MI, when measuring between RW and RL.
0
Roffset = RW
/MI, when measuring between RW and RH.
127
17. RDNL = (RW – RW )/MI -1, for i = 16 to 127.
i-1
i
18. RINL = [RW – (MI • i) – RW ]/MI, for i = 16 to 127.
i
0
6
[Max(Ri) – Min(Ri)]
10
19.
for i = 16 to 127, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min( ) is the
minimum value of the resistance over the temperature range.
------------------------------------------------------ ---------------------
TC
=
×
R
Ri(+25°C)
+165°C
20. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
FN7901.0
August 3, 2011
7
ISL23418
DCP Macro Model
R
TOTAL
RH
RL
C
L
C
H
C
W
32pF
32pF
32pF
RW
Timing Diagrams
Input Timing
t
CS
CS
t
t
t
LAG
LEAD
CYC
SCK
SDI
...
t
WH
t
t
t
RI
FI
t
t
WL
SU
H
...
MSB
LSB
SDO
Output Timing
CS
SCK
SDO
SDI
...
...
t
t
t
SO
HO
DIS
MSB
LSB
t
V
ADDR
XDCP™ Timing (for All Load Instructions)
CS
t
DCP
SCK
...
...
MSB
LSB
SDI
V
W
SDO
*When CS is HIGH
SDO at Z or Hi-Z state
FN7901.0
August 3, 2011
8
ISL23418
Typical Performance Curves
0.4
0.30
0.2
0
0.15
0
-0.2
-0.4
-0.15
-0.30
0
0
0
25
50
75
100
125
125
125
0
25
50
75
100
125
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 3. 10k DNL vs TAP POSITION, V = 5V
CC
FIGURE 4. 50k DNL vs TAP POSITION, V = 5V
CC
0.30
0.15
0
0.4
0.2
0
-0.2
-0.4
-0.15
-0.30
0
25
50
75
100
125
25
50
75
100
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 5. 10k INL vs TAP POSITION, V = 5V
CC
FIGURE 6. 50k INL vs TAP POSITION, V = 5V
CC
0.4
0.2
0
0.30
0.15
0
-0.2
-0.4
-0.15
-0.30
25
50
75
100
0
25
50
75
100
125
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 7. 10k RDNL vs TAP POSITION, V = 5V
CC
FIGURE 8. 50k RDNL vs TAP POSITION, V = 5V
CC
FN7901.0
August 3, 2011
9
ISL23418
Typical Performance Curves (Continued)
0.6
0.4
0.2
0
0.30
0.15
0
-0.2
-0.4
-0.6
-0.15
-0.30
0
25
50
75
100
125
0
25
50
75
100
125
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 9. 10k RINL vs TAP POSITION, V = 5V
CC
FIGURE 10. 50k RINL vs TAP POSITION, V = 5V
CC
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
+125°C
+125°C
+25°C
+25°C
-40°C
-40°C
0
25
50
75
100
125
0
25
50
75
100
125
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 11. 10k WIPER RESISTANCE vs TAP POSITION, V = 5V
CC
FIGURE 12. 50k WIPER RESISTANCE vs TAP POSITION, V = 5V
CC
300
250
200
150
100
50
70
60
50
40
30
20
10
0
0
7.5
32.5
57.5
82.5
107.5
7.5
32.5
57.5
82.5
107.5
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 13. 10k TCv vs TAP POSITION
FIGURE 14. 50k TCv vs TAP POSITION
FN7901.0
August 3, 2011
10
ISL23418
Typical Performance Curves (Continued)
600
500
400
300
200
100
0
200
150
100
50
0
7.5
7.5
32.5
57.5
82.5
107.5
32.5
57.5
82.5
107.5
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 15. 10k TCr vs TAP POSITION
FIGURE 16. 50k TCr vs TAP POSITION
35
30
25
20
15
10
5
120
90
60
30
0
0
7.5
32.5
57.5
82.5
107.5
7.5
32.5
57.5
82.5
107.5
TAP POSITION (DECIMAL)
TAP POSITION (DECIMAL)
FIGURE 17. 100k TCv vs TAP POSITION
FIGURE 18. 100k TCr vs TAP POSITION
SCK CLOCK
RW PIN
CH1: 1V/DIV, 1µs/DIV
CH2: 10mV/DIV, 1µs/DIV
20mV/DIV
5µs/DIV
FIGURE 19. WIPER DIGITAL FEEDTHROUGH
FIGURE 20. WIPER TRANSITION GLITCH
FN7901.0
August 3, 2011
11
ISL23418
Typical Performance Curves (Continued)
1V/DIV
1V/DIV
1µs/DIV
0.1s/DIV
VRW
CS RISING EDGE
FIGURE 21. WIPER LARGE SIGNAL SETTLING TIME
FIGURE 22. POWER-ON START-UP IN VOLTAGE DIVIDER MODE
1.2
1.0
0.8
CH1: 0.5V/DIV, 0.2µs/DIV RH PIN
CH2: 0.2V/DIV, 0.2µs/DIV RW PIN
V
= 5.5V, V
= 5.5V
LOGIC
CC
0.6
0.4
0.2
0
V
= 1.7V, V
= 1.2V
LOGIC
CC
R
= 10k
TOTAL
-40
-15
10
35
60
85
110
-3dB FREQUENCY = 1.4MHz AT MIDDLE TAP
TEMPERATURE (°C)
FIGURE 23. 10k -3dB CUT OFF FREQUENCY
FIGURE 24. STANDBY CURRENT vs TEMPERATURE
FN7901.0
August 3, 2011
12
ISL23418
Voltage at any DCP pins, RH, RL, or RW should not exceed V
CC
Functional Pin Descriptions
Potentiometers Pins
RH AND RL
level at any conditions during power-up and normal operation.
The V pin must be connected to the SPI bus supply, which
LOGIC
allows reliable communication with a wide range of
microcontrollers, independently of the V level. This is
CC
extremely important in systems in which the digital supply has
lower levels than the analog supply.
The high (RH) and low (RL) terminals of the ISL23418 are
equivalent to the fixed terminals of a mechanical potentiometer.
The RH and RL are referenced to the relative position of the wiper
and not to the voltage potential on the terminals. With the WR
register set to 127 decimal, the wiper is closest to RH, and with
the WR register set to 0, the wiper is closest to RL.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of DCP are
equivalent to the fixed terminals of a mechanical potentiometer
(RH and RL pins). The RW pin of the DCP is connected to
intermediate nodes and is equivalent to the wiper terminal of a
mechanical potentiometer. The position of the wiper terminal
within the DCP is controlled by the 8-bit volatile Wiper Register
(WR). When the WR of a DCP contains all zeroes (WR[7:0] = 00h),
its wiper terminal (RW) is closest to its “Low” terminal (RL). When
the WR register of a DCP contains all ones (WR[7:0] = 7Fh), its
wiper terminal (RW) is closest to its “High” terminal (RH). As the
value of WR increases from all zeroes (0) to all ones (127
decimal), the wiper moves monotonically from the position
closest to RL to the position closest to RH. At the same time, the
resistance between RW and RL increases monotonically, while
the resistance between RH and RW decreases monotonically.
RW
RW is the wiper terminal, and it is equivalent to the moveable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WR register.
Bus Interface Pins
SERIAL CLOCK (SCK)
The SCK input is the serial clock of the SPI serial interface.
SERIAL DATA INPUT (SDI)
SDI is a serial data input pin for the SPI interface. SDI receives
operation code, wiper address and data from the SPI remote
host device. The data bits are shifted in at the rising edge of the
serial clock, SCK, while CS input is low.
While the ISL23418 is being powered up, the WR is reset to 40h
(64 decimal), which locates RW to the mid value between RL and
RH.
SERIAL DATA OUTPUT (SDO)
WR can be read or written to directly using the SPI serial
interface as described in the following sections.
SDO is a serial data output pin. During a read cycle, the data bits
are shifted out on the falling edge of the serial clock SCK and are
available to the master on the following rising edge of SCK.
Memory Description
The output type is configured through ACR[1] bit for Push-Pull or
Open Drain operation. Default setting for this pin is Push-Pull. An
external pull-up resistor is required for Open Drain output
operation. When CS is HIGH, the SDO pin is in tri-state (Z) or
high-tri-state (Hi-Z), depending on the selected configuration.
The ISL23418 contains two volatile 8-bit registers: the Wiper
Register (WR) and the Access Control Register (ACR). A memory
map of ISL23418 is shown in Table 1. WR, at address 0, contains
the current wiper position of the DCP. ACR, at address 10h,
contains information and control bits as described in Table 2.
CHIP SELECT (CS)
TABLE 1. MEMORY MAP
CS LOW enables the ISL23418, placing it in the active power
mode. A HIGH to LOW transition on CS is required prior to the
start of any operation after power-up. When CS is HIGH, the
ISL23418 is deselected, the SDO pin is at high impedance, and
the device is in standby state.
ADDRESS
(hex)
DEFAULT SETTING
(hex)
VOLATILE
ACR
10
0
40
80
WR
VLOGIC
TABLE 2. ACCESS CONTROL REGISTER (ACR)
VLOGIC is an input pin that supplies an internal level translator
for serial bus operation from 1.2V to 5.5V.
BIT #
7
6
5
0
4
0
3
0
2
0
1
0
0
NAME
0
SHDN
SDO
Principles of Operation
Shutdown Function
The ISL23418 is an integrated circuit incorporating one DCP with
its associated registers and an SPI serial interface providing
direct communication between a host and the potentiometer.
The resistor array is composed of individual resistors connected
in series. At either end of the array and between each resistor is
an electronic switch that transfers the potential at that point to
the wiper. The electronic switches on the device operate in a
“make before break” mode when the wiper changes tap
positions.
The SHDN bit (ACR[6]) disables or enables shutdown mode for all
DCP channels simultaneously. When this bit is 0, DCP is forced to
end-to-end open circuit, and RW is connected to RL through a
2kΩ serial resistor, as shown in Figure 25. Default value of the
SHDN bit is 1.
FN7901.0
August 3, 2011
13
ISL23418
SPI Serial Interface
RH
The ISL23418 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output, with data
clocked in on the rising edge of SCK and clocked out on the
falling edge of SCK. CS must be LOW during communication with
the ISL23418. The SCK and CS lines are controlled by the host or
master. The ISL23418 operates only as a slave device. All
communication over the SPI interface is conducted by sending
the MSB of each byte of data first.
RW
RL
2kΩ
Protocol Conventions
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
The SPI protocol contains an Instruction Byte followed by one or
more Data Bytes. A valid Instruction Byte contains instruction as
the three MSBs, with the following five register address bits
(Table 3). The next byte sent to the ISL23418 is the Data Byte.
In shutdown mode, the RW terminal is shorted to the RL terminal
with around 2kΩ resistance, as shown in Figure 25. When the device
enters shutdown, all current DCP WR settings are maintained. When
the device exits shutdown, the wipers return to the previous WR
settings after a short settling time (Figure 26).
TABLE 3. INSTRUCTION BYTE FORMAT
BIT #
7
6
5
4
3
2
1
0
I2
I1
I0
R4
R3
R2
R1
R0
Table 4 contains a valid instruction set for ISL23418. If the
[R4:R0] bits are zero, then the read or write is to the WR register. If
the [R4:R0] bits are 10000, then the operation is to the ACR.
POWER-UP
MID SCALE = 40H
USER PROGRAMMED
AFTER SHDN
Write Operation
SHDN RELEASED
A write operation to the ISL23418 is a two or more bytes
operation. It first requires CS to transition from HIGH to LOW.
Then the host sends a valid Instruction Byte to the SDI pin,
followed by one or more Data Bytes. The host terminates the
write operation by pulling the CS pin from LOW to HIGH. The
instruction is executed on the rising edge of CS (Figure 27).
SHDN ACTIVATED
WIPER RESTORE TO
ORIGINAL POSITION
SHDN MODE
TIME (s)
0
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
Read Operation
In shutdown mode, if there is a glitch in the power supply that
causes it to drop below 1.3V for more than 0.2µs to 0.4µs, the
wipers are RESET to their mid position. This is done to avoid an
undefined state at the wiper outputs.
A read operation to the ISL23418 is a four-byte operation. First,
the CS transitions from HIGH to LOW. Then the host sends a valid
Instruction Byte to the SDI pin, followed by a “dummy” Data Byte,
an NOP Instruction Byte, and another “dummy” Data Byte. The
SPI host receives the Instruction Byte (instruction code + register
address) and the requested Data Byte from the SDO pin on the
rising edge of SCK during the third and fourth bytes, respectively.
The host terminates the read by pulling the CS pin from LOW to
HIGH (Figure 28).
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
I2
0
0
0
1
1
I1
0
0
1
0
1
I0
0
1
1
0
0
R4
X
R3
X
R2
X
R1
X
R0
X
OPERATION
NOP
X
X
X
X
X
ACR READ
X
X
X
X
X
ACR WRTE
R4
R4
R3
R3
R2
R2
R1
R1
R0
R0
WR or ACR READ
WR or ACR WRTE
where “X” means “do not care.”
FN7901.0
August 3, 2011
14
ISL23418
CS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SCK
DATA BYTE
WR INSTRUCTION
ADDR
SDI
SDO
FIGURE 27. TWO-BYTE WRITE SEQUENCE
1
8
16
24
32
CS
SCK
NOP
RD
ADDR
SDI
RD
ADDR
READ DATA
SDO
FIGURE 28. FOUR-BYTE READ SEQUENCE
FN7901.0
August 3, 2011
15
ISL23418
First there is a HIGH-to-LOW transition on the CS line, followed by
Applications Information
Communicating with ISL23418
Communication with ISL23418 is accomplished by using the SPI
interface through the ACR (address 10000b) and WR (address
00000b) registers.
N two-byte read instructions on the SDI line, with reversed chain
access sequence. The instruction byte + dummy data byte for the
last DCP in the chain goes first, followed by a LOW-to-HIGH
transition on the CS line. The read instructions are executed
during the second part of the read sequence. It also starts by a
HIGH-to-LOW transition on the CS line, followed by N number of
two-byte NOP instructions on the SDI line and a LOW-to-HIGH
transition of CS. The data is read on every even byte during the
second part of the read sequence, while every odd byte contains
code 111b followed by the address from which the data is being
read.
The wiper of the potentiometer is controlled by the WR register.
Writes and reads can be made directly to these registers to
control and monitor the wiper position.
Daisy Chain Configuration
When an application needs more than one ISL23418, it can
communicate with all of them without additional CS lines by
daisy chaining the DCPs, as shown in Figure 29. In daisy chain
configuration, the SDO pin of the previous chip is connected to
the SDI pin of the following chip, and each CS and SCK pin is
connected to the corresponding microcontroller pin in parallel,
like regular SPI interface implementation. The daisy chain
configuration can also be used for simultaneous setting of
multiple DCPs. Note that the number of daisy chained DCPs is
limited only by the driving capabilities of the SCK and CS pins of
the microcontroller. For a larger number of SPI devices, buffering
of the SCK and CS lines is required.
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can exhibit noticeable voltage
transients or overshoot/undershoot, which results from the
sudden transition from a very low impedance “make” to a much
higher impedance “break” within a short period of time (<1µs).
Several code transitions, such as 0Fh to 10h, 1Fh to 20h,..., and
EFh to 7Fh, have higher transient glitch. Note that all switching
transients settle well within the settling time as stated in the
datasheet. A small capacitor can be added externally to reduce
the amplitude of these voltage transients, but this also reduces
the useful bandwidth of the circuit, which may not be a good
solution for some applications. Using fast amplifiers in a signal
chain for fast recovery may be a good idea in these cases.
Daisy Chain Write Operation
The write operation starts with a HIGH to LOW transition on the
CS line, followed by N number of two-byte write instructions on
the SDI line, with reversed chain access sequence. The
instruction byte + data byte for the last DCP in the chain go first,
as shown in Figure 30, where N is the number of DCPs in the
chain. Serial data is going through the DCPs from DCP0 to
DCP(N-1) as follows: DCP0 --> DCP1 --> DCP2 --> ... --> DCP(N-1).
The write instruction is executed on the rising edge of CS for all N
DCPs simultaneously.
V
Requirements
LOGIC
Keeping V
powered all the time during normal operation is
LOGIC
recommended. In cases in which turning V
necessary, grounding the V
OFF is
LOGIC
pin is recommended. Grounding
LOGIC
the V
LOGIC
pin or both V
LOGIC
and V does not affect other
CC
devices on the same bus. It is good practice to put a 1µF capacitor
in parallel with a 0.1µF decoupling capacitor close to the V pin.
LOGIC
V
Requirements and Placement
Daisy Chain Read Operation
CC
Putting a 1µF capacitor in parallel with a 0.1µF decoupling capacitor
The read operation consists of two parts. First, the read
instructions (N two-byte operations) are sent with a valid address.
Second, the requested data is read while sending NOP
instructions (N two-byte operations), as shown in
Figures 31 and 32.
close to the V pin is recommended.
CC
N DCP IN A CHAIN
CS
SCK
DCP0
DCP1
DCP2
DCP(N-1)
CS
MOSI
MISO
CS
CS
CS
SCK
SDI
SCK
SDI
SCK
SDI
SCK
SDI
µC
SDO
SDO
SDO
SDO
FIGURE 29. DAISY CHAIN CONFIGURATION
FN7901.0
August 3, 2011
16
ISL23418
CS
SCK
16 CLKS
C P0
16 CLKLS
P2
16 CLKS
WR
D C
WR
WR
D
D
C
C
P1
P2
WR
WR
D
SDI
D
C P1
SDO 0
WR
D C P2
SDO 1
SDO 2
FIGURE 30. DAISY CHAIN WRITE SEQUENCE OF N = 3 DCP
CS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SCK
SDI
INSTRUCTION
ADDR
DATA IN
SDO
DATA OUT
FIGURE 31. TWO-BYTE READ INSTRUCTION
CS
SCK
SDI
16 CLKS
RD DCP2
16 CLKS
RD DCP1
16 CLKS
RD DCP0
16 CLKS
NOP
16 CLKS
NOP
16 CLKS
NOP
DCP0 OUT
DCP2 OUT
DCP1 OUT
SDO
FIGURE 32. DAISY CHAIN READ SEQUENCE OF N = 3 DCP
FN7901.0
August 3, 2011
17
ISL23418
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest revision.
DATE
REVISION
FN7901.0
CHANGE
8/3/2011
Initial Release
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on
intersil.com: ISL23418
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7901.0
August 3, 2011
18
ISL23418
Mini Small Outline Plastic Packages (MSOP)
N
M10.118 (JEDEC MO-187BA)
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE
INCHES
MILLIMETERS
E1
E
SYMBOL
MIN
MAX
MIN
0.94
0.05
0.75
0.18
0.09
2.95
2.95
MAX
1.10
0.15
0.95
0.27
0.20
3.05
3.05
NOTES
A
A1
A2
b
0.037
0.002
0.030
0.007
0.004
0.116
0.116
0.043
0.006
0.037
0.011
0.008
0.120
0.120
-
-B-
0.20 (0.008)
INDEX
AREA
1 2
A
B
C
-
-
TOP VIEW
4X θ
9
0.25
(0.010)
R1
c
-
R
GAUGE
PLANE
D
3
E1
e
4
SEATING
PLANE
L
0.020 BSC
0.50 BSC
-
-C-
4X θ
L1
A
A2
E
0.187
0.016
0.199
0.028
4.75
0.40
5.05
0.70
-
L
6
SEATING
PLANE
L1
N
0.037 REF
10
0.95 REF
10
-
0.10 (0.004)
-A-
C
C
b
7
-H-
A1
e
R
0.003
0.003
-
-
0.07
0.07
-
-
-
D
0.20 (0.008)
C
R1
θ
-
o
o
o
o
a
SIDE VIEW
5
15
5
15
-
C
L
o
o
o
o
0
6
0
6
-
α
E
1
-B-
Rev. 0 12/02
0.20 (0.008)
C
D
END VIEW
NOTES:
1. These package dimensions are within allowable dimensions of
JEDEC MO-187BA.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs and are measured at Datum Plane. Mold flash, protrusion
and gate burrs shall not exceed 0.15mm (0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions
- H -
and are measured at Datum Plane.
Interlead flash and
protrusions shall not exceed 0.15mm (0.006 inch) per side.
5. Formed leads shall be planar with respect to one another within
0.10mm (.004) at seating Plane.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.08mm (0.003 inch) total in excess
of “b” dimension at maximum material condition. Minimum space
between protrusion and adjacent lead is 0.07mm (0.0027 inch).
- B -
-A -
10. Datums
and
to be determined at Datum plane
.
- H -
11. Controlling dimension: MILLIMETER. Converted inch dimen-
sions are for reference only
FN7901.0
August 3, 2011
19
ISL23418
Package Outline Drawing
L10.2.1x1.6A
10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 5, 3/10
8.
PIN 1
INDEX AREA
2.10
A
PIN #1 ID
8.
0.05 MIN.
B
1
4
1
4X 0.20 MIN.
0.10 MIN.
10
5
0.80
10X 0.40
10 X 0.20
0.10
6
9
2X
6X 0.50
4
TOP VIEW
(10 X 0.20)
0.10 M C A B
M C
BOTTOM VIEW
SEE DETAIL "X"
(0.05 MIN)
(0.10 MIN.)
MAX. 0.55
PACKAGE
OUTLINE
1
0.10 C
C
(10X 0.60)
SEATING PLANE
0.08 C
(2.00)
SIDE VIEW
0 . 125 REF
(0.80)
(1.30)
C
(6X 0.50 )
(2.50)
0-0.05
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5M-1994.
2. All Dimensions are in millimeters. Angles are in degrees.
Dimensions in ( ) for Reference Only.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Lead width dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Maximum package warpage is 0.05mm.
6. Maximum allowable burrs is 0.076mm in all directions.
7. Same as JEDEC MO-255UABD except:
No lead-pull-back, MIN. Package thickness = 0.45 not 0.50mm
Lead Length dim. = 0.45mm max. not 0.42mm.
8. The configuration of the pin #1 identifier is optional, but must be located within
the zone indicated. The pin #1 identifier may be either a mold or mark feature.
FN7901.0
August 3, 2011
20
相关型号:
ISL23418UFUZ-T7A
Single, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCP™); MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL23418UFUZ-TK
Single, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCP™); MSOP10; Temp Range: -40° to 125°C
RENESAS
ISL23418WFRUZ-T7A
Single, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCPâ¢)
INTERSIL
ISL23418WFUZ-T
10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 128 POSITIONS, PDSO10, ROHS COMPLIANT, PLASTIC, MO-187BA, MSOP-10
RENESAS
ISL23418WFUZ-T7A
Single, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCP™); MSOP10, uTQFN10; Temp Range: -40° to 125°C
RENESAS
©2020 ICPDF网 联系我们和版权申明