ISL29035 [RENESAS]
Integrated Digital Light Sensor with Interrupt;
| 型号： | ISL29035 |
| 厂家： | 
RENESAS TECHNOLOGY CORP |
| 描述： | Integrated Digital Light Sensor with Interrupt |
| 文件： | 总17页 (文件大小：774K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DATASHEET
ISL29035
Integrated Digital Light Sensor with Interrupt
FN8371
Rev 3.00
December 12, 2016
The ISL29035 is an integrated ambient and infrared
Features
light-to-digital converter with I2C (SMBus compatible) Interface. Its
advanced self-calibrated photodiode array emulates human eye
response with excellent IR rejection. The on-chip ADC is capable
of rejecting 50Hz and 60Hz flicker caused by artificial light
sources. The Lux range select feature allows users to program the
Lux range for optimized counts/Lux.
• Resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-bit ADC
• Wide dynamic range . . . . . . . . . . . . . . . . . . . . . . . . . .1:4,200,000
• Integrated noise reduction . . . . . . . . . . . . . . . . . . . . . 50/60Hz
• Close to human eye response with excellent IR/UV rejection
• Shutdown modes. . . . . . . . . . . . . . . . . . . .software and automatic
• Programmable interrupt threshold with persistence filter
• Supply current (typical) . . . . . . . . . . . . . . . . . . . . . . . . . . . 57µA
• Shutdown current (maximum) . . . . . . . . . . . . . . . . . . . 0.51µA
• I2C (SMB compatible) power supply . . . . . . . . . 1.7V to 3.63V
• Sensor power supply . . . . . . . . . . . . . . . . . . . . .2.25V to 3.63V
• Operating temperature range. . . . . . . . . . . . . -40°C to +85°C
• Small form factor package. . . . . . . 6 Ld 1.5x1.6x0.75 ODFN
For ambient light sensing, an internal 16-bit ADC has been
designed based upon the charge-balancing technique. The
ADC conversion time is nominally 105ms and is user
adjustable from 11µs to 105ms, depending on oscillator
frequency and ADC resolution. In normal operation, typical
current consumption is 57µA. In order to further minimize
power consumption, two power-down modes have been
provided. If polling is chosen over continuous measurement of
light, the auto power-down function shuts down the whole chip
after each ADC conversion for the measurement. The other
power-down mode is controlled by software via the I2C
interface. The power consumption can be reduced to less than
0.3µA when powered down.
Applications
• Mobile devices: smart phone, PDA, GPS
• Computing devices: notebook PC, MacBook, tablets
• Consumer devices: LCD-TV, digital camera
• Industrial and medical light sensing
The ISL29035 supports a software brownout condition
detection. The device powers up with the brownout bit asserted
until the host clears it through the I2C interface.
The ISL29035 supports a software and hardware interrupt that
remains asserted until the host clears it through the I2C
interface. Function of ADC conversion continues without
stopping after interrupt is asserted.
Related Literature
• AN1591, “Evaluation Hardware/Software Manual for ALS
and Proximity Sensor”
Designed to operate on supplies from 2.25V to 3.63V with an I2C
supply from 1.7V to 3.63V, the ISL29035 is specified for
operation across the -40°C to +85°C ambient temperature
range.
TABLE 1. KEY DIFFERENCES BETWEEN FAMILY OF PARTS
NUMBER OF
PART NUMBER ALS SENSING INTERRUPT PIN
PINS
4 Ld
6 Ld
ISL29034
ISL29035
Yes
Yes
No
Yes
FN8371 Rev 3.00
December 12, 2016
Page 1 of 17
ISL29035
100
VDD
VDD_PULLUP
4.7k 4.7k
1.2
1.0
0.8
0.6
0.4
0.2
0
1µF
4.7k
1
HUMAN EYE
VDD
SDA
SCL
SDA
SCL
INT
6
5
4
AMBIENT LIGHT SENSOR
3
ISL29035
NC
MCU
GPIO
GND
2
300
400
500
600
700
800
900
1000 1100
WAVELENGTH (nm)
FIGURE 2. NORMALIZED SPECTRAL RESPONSE FOR AMBIENT
LIGHT SENSING
FIGURE 1. ISL29035 TYPICAL APPLICATION DIAGRAM
FN8371 Rev 3.00
December 12, 2016
Page 2 of 17
ISL29035
Block Diagram
VDD
1
IREF
fOSC
COMMAND
REGISTER
R
5
6
SCL
SDA
500k
I2C/SMB
PHOTODIODE
ARRAY
INTEGRATING
ADC
DATA
Register
LIGHT DATA
PROCESS
INTERRUPT
2
4
GND
INT
FIGURE 3. BLOCK DIAGRAM
Pin Configuration
Pin Descriptions
ISL29035
PIN
(6 LD ODFN)
TOP VIEW
NUMBER PIN NAME
DESCRIPTION
1
2
3
4
VDD
GND
NC
Positive supply
Ground pin
VDD
GND
NC
1
2
3
6
5
4
SDA
SCL
INT
No connect
INT
Interrupt pin; LOW for interrupt alarming. INTpin
is an open-drain. INT remains asserted until the
interrupt status bit is reset.
5
6
SCL
SDA
I2C serial clock
I2C serial data
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
TEMP RANGE
TAPE AND REEL
(UNITS)
PACKAGE
(RoHS COMPLIANT)
PKG.
DWG. #
(°C)
ISL29035IROZ-T7
ISL29035IROZ-T7A
ISL29035EVAL1Z
NOTES:
-40 to +85
3k units
6 Ld ODFN
6 Ld ODFN
L6.1.5x1.6
L6.1.5x1.6
-40 to +85
250 units
Evaluation Board
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu-Ag
plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are
MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see product information page for ISL29035. For more information on MSL, please see tech brief TB477.
FN8371 Rev 3.00
December 12, 2016
Page 3 of 17
ISL29035
Absolute Maximum Ratings
Thermal Information
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.0V
I2C Bus (SCL, SDA) and INT Pin Voltage. . . . . . . . . . . . . . . . . . -0.2V to 4.0V
I2C Bus (SCL, SDA) and INT Pin Current. . . . . . . . . . . . . . . . . . . . . . . <10mA
Input Voltage Slew Rate (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1V/µs
ESD Ratings
Thermal Resistance (Typical)
JA (°C/W)
210
6 Ld ODFN Package (Note 4) . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (TJMAX). . . . . . . . . . . . . . . . . . . . . . .+90°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB477
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3kV
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTE:
4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
Electrical Specifications VDD = 3.0V, TA = +25°C, 16-bit ADC operation, unless otherwise specified.
MIN
MAX
DESCRIPTION
Power Supply Range
PARAMETER
TEST CONDITIONS
(Note 7)
TYP
(Note 7)
UNIT
V
VDD
IDD
2.25
3.63
85
Supply Current
57
µA
Supply Current when Powered Down
Supply Voltage Range for I2C Interface
ADC Integration/Conversion Time
I2C Clock Rate Range
IDD1
VI2C
tint
Software disabled or auto power-down
16-bit ADC data
0.24
0.51
3.63
µA
1.7
V
105
400
1
ms
FI2
kHz
Counts
Counts
%
C
Count Output when Dark
DATA_0
DATA_F
%/Value
E = 0 Lux, Range 0 (1k Lux)
5
Full Scale ADC Code
65535
Part-to-Part Variation (3 Population)
E = 300 Lux, cold white LED
Range 0 (1k Lux)
±5
Light Count Output with LSB of 0.015 Lux/Count
Light Count Output with LSB of 0.06 Lux/Count
Light Count Output with LSB of 0.24 Lux/Count
Light Count Output with LSB of 0.96 Lux/Count
ADCR0
ADCR1
ADCR2
ADCR3
E = 300 Lux, cold white LED (Note 5),
ALS Range 0 (1k Lux)
20473
5100
1400
366
Counts
Counts
Counts
Counts
E = 300 Lux, cold white LED (Note 5),
ALS Range 1 (4k Lux)
E = 300 Lux, cold white LED (Note 5),
ALS Range 2 (16k Lux)
E = 300 Lux, cold white LED (Note 5),
ALS Range 3 (64k Lux)
Infrared Count Output (Note 6)
Infrared Count Output (Note 6)
Infrared Count Output (Note 6)
Infrared Count Output (Note 6)
SDA Current Sinking Capability
INT Current Sinking Capability
NOTES:
ADC_IRR0 Range 0 (1k Lux)
ADC_IRR1 Range 1 (4k Lux)
ADC_IRR2 Range 2 (16k Lux)
ADC_IRR3 Range 3 (64k Lux)
ISDA
1402
1997
481
148
42
2598
Counts
Counts
Counts
Counts
mA
4
4
5
IINT
5
mA
5. 550nm green LED is used in production test. The 550nm LED irradiance is calibrated to produce the same DATA count against an illuminance level
of 300 Lux Cold White LED.
6. 850nm IR LED is used in production test. The 850nm LED irradiance is calibrated to produce the same DATA_IR count against and illuminance level
of 210 lux sunlight at sea level.
7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
FN8371 Rev 3.00
December 12, 2016
Page 4 of 17
ISL29035
2
I C Interface Specifications VDD = 3.0V, TA = +25°C, 16-bit ADC operation, unless otherwise specified.
MIN
MAX
PARAMETER
SYMBOL
VIL
TEST CONDITIONS
(Note 7)
TYP
(Note 7) UNIT
SDA and SCL Input Buffer LOW Voltage
SDA and SCL Input Buffer HIGH Voltage
SDA and SCL Input Buffer Hysteresis
0.55
V
V
V
VIH
1.25
VHys
(Note 8)
0.05 x
VDD
SDA Output Buffer LOW Voltage
(Open-Drain), Sinking 4mA
VOL
(Note 8)
0
0.06
0.4
10
V
SDA and SCL Pin Capacitance
CPIN
TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V,
pF
(Note 8)
VOUT = 0V
SCL Frequency
fSCL
tIN
400
50
kHz
ns
Pulse Width Suppression Time at SDA
and SCL Inputs
Any pulse narrower than the maximum
specification is suppressed
SCL Falling Edge to SDA Output Data Valid
tAA
900
ns
ns
Time the Bus Must be Free before the
Start of a New Transmission
tBUF
1300
Clock LOW Time
tLOW
tHIGH
1300
600
600
600
100
30
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock HIGH Time
START Condition Set-Up Time
START Condition Hold Time
Input Data Set-Up Time
Input Data Hold Time
tSU:STA
tHD:STA
tSU:DAT
tHD:DAT
tSU:STO
tHD:STO
tDH
STOP Condition Set-Up Time
STOP Condition Hold Time
Output Data Hold Time
SDA and SCL Rise Time
600
600
0
tR
20 + 0.1 x
Cb
(Note 8)
SDA and SCL Fall Time
tF
20 + 0.1 x
Cb
ns
pF
k
(Note 8)
Capacitive Loading of SDA or SCL
Cb
(Note 10)
Total on-chip and off-chip
400
SDA and SCL Bus Pull-Up Resistor
Off-Chip
RPU
(Note 8)
Maximum is determined by tR and tF.
For Cb = 400pF, max is about 2kΩ ~ 2.5kΩ
For Cb = 40pF, max is about 15kΩ ~ 20kΩ
1
NOTES:
8. Limits should be considered typical and are not production tested.
9. These are I2C specific parameters and are not tested, however, they are used to set conditions for testing devices to validate specification.
10. Cb is the capacitance of the bus in pF.
FN8371 Rev 3.00
December 12, 2016
Page 5 of 17
ISL29035
SDA vs SCL Timing
t
t
LOW
HIGH
t
HD:STO
t
t
R
F
SCL
t
SU:DAT
t
t
HD:DAT
t
SU:STA
SU:STO
t
HD:STA
SDA
(INPUT TIMING)
t
t
BUF
DH
t
AA
SDA
(OUTPUT TIMING)
FIGURE 4. I2C BUS TIMING
SCL
SDA
ACK
TH
8
BIT OF LAST BYTE
t
WC
STOP
CONDITION
START
CONDITION
FIGURE 5. I2C WRITE CYCLE TIMING
FN8371 Rev 3.00
December 12, 2016
Page 6 of 17
ISL29035
Typical Performance Curves
1.2
1.2
1.0
0.8
0.6
0.4
0.2
0
1.0
HUMAN EYE
0.8
AMBIENT LIGHT SENSOR
0.6
0.4
0.2
0
300
400
500
600
700
800
900
1000 1100
-60 -50 -40 -30 -20 -10
0
10 20 30 40 50 60
WAVELENGTH (nm)
ANGLE (°)
FIGURE 6. NORMALIZED SPECTRAL RESPONSE FOR AMBIENT
LIGHT SENSING
FIGURE 7. NORMALIZED RADIATION PATTERN
14
1000
800
600
400
12
1000 LUX RANGE
10
1000 LUX RANGE
8
6
4
2
0
200
0
-60 -50 -40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100
0
200
400
600
800
1000
TEMPERATURE (°C)
AMBIENT LIGHT (LUX)
FIGURE 8. TEMPERATURE TEST IN DARK CONDITION
FIGURE 9. ALS TRANSFER FUNCTION
FN8371 Rev 3.00
December 12, 2016
Page 7 of 17
ISL29035
Interrupt Function
The active low interrupt pin is an open-drain pull-down
Principles of Operation
Photodiodes and ADC
The ISL29035 contains two photodiode arrays, which convert
light into current. The spectral response for ambient light sensing
is shown in Figure 6 on page 7. After light is converted to current
during the light signal process, the current output is converted to
digital by a built-in 16-bit Analog-to-Digital Converter (ADC). An
I2C command reads the ambient light or IR intensity in counts.
configuration. The interrupt pin serves as an alarm or monitoring
function to determine whether the ambient light level exceeds
the upper threshold or goes below the lower threshold. It should
be noted that the function of ADC conversion continues without
stopping after interrupt is asserted. If the user needs to read the
ADC count that triggers the interrupt, the reading should be done
before the data registers are refreshed by the following
conversions. The user can also configure the persistence of the
interrupt pin. This reduces the possibility of false triggers, such as
noise or sudden spikes in ambient light conditions. An
The converter is a charge-balancing integrating type 16-bit ADC.
The chosen method for conversion is best for converting small
current signals in the presence of an AC periodic noise. A 105ms
integration time, for instance, highly rejects 50Hz and 60Hz
power line noise simultaneously.
unexpected camera flash, for example, can be ignored by setting
the persistence to 8 integration cycles.
Serial Interface
The integration time of the built-in ADC is determined by the
internal oscillator, and the n-bit (n = 4, 8, 12, 16) counter inside
the ADC. A good balancing act of integration time and resolution
(depending on the application) is required for optimal results.
The ISL29035 supports the Inter-Integrated Circuit (I2C) bus data
transmission protocol. The I2C bus is a two-wire serial
bidirectional interface consisting of SCL (Clock) and SDA (Data).
Both the wires are connected to the device supply via pull-up
resistors. The I2C protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and the
device being controlled is the slave. The transmitting device pulls
down the SDA line to transmit a “0” and releases it to transmit a
“1”. The master always initiates the data transfer, only when the
bus is not busy, and provides the clock for both transmitting and
receiving operations. The ISL29035 operates as a slave device in
all applications. The serial communication over the I2C interface
is conducted by sending the Most Significant Bit (MSB) of each
byte of data first.
The ADC has I2C programmable range select to dynamically
accommodate various lighting conditions. For very dim
conditions, the ADC can be configured at its lowest range
(Range 0) in the ambient light sensing.
Low-Power Operation
The ISL29035 initial operation is at the power-down mode after a
supply voltage is provided. The data registers contain the default
value of 0. When the ISL29035 receives an I2C command to do a
one-time measurement from an I2C master, it will start ADC
conversion with light sensing. The ISL29035 will go to the
power-down mode automatically after one conversion is finished
and keep the conversion data available for the master to fetch
anytime afterwards. When receiving an I2C command of
continuous measurement, the device will continuously do ADC
conversions with light sensing and will continuously update the
data registers with the latest conversion data. The device will go
into power-down mode after receiving the power-down I2C
command.
Start Condition
During data transfer, the SDA line must remain stable while the
SCL line is HIGH. All I2C interface operations must begin with a
START condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH (refer to Figure 12 on page 9). The ISL29035
continuously monitors the SDA and SCL lines for the START
condition and does not respond to any command until this
condition is met (refer to Figure 12). A START condition is ignored
during the power-up sequence.
Ambient Light and IR Sensing
There are four operational modes in ISL29035: Programmable
ALS once with auto power-down, programmable IR sensing once
with auto power-down, programmable continuous ALS sensing
and programmable continuous IR sensing. These four modes can
be programmed in series to fulfill the application needs. The
detailed program configuration is listed in “Command-I Register
(Address: 0x00)” on page 11.
Stop Condition
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL is
HIGH (refer to Figure 12). A STOP condition at the end of a
read/write operation places the device in its standby mode. If a
stop is issued in the middle of a Data byte, or before 1 full Data
byte + ACK is sent, then the serial communication of the
ISL29035 resets itself without performing the read/write. The
contents of the array are not affected.
When the part is programmed for ambient light sensing, the
ambient light wavelength within the “Ambient Light Sensing”
spectral response curve in Figure 15 is converted into current.
With ADC, the current is converted to an unsigned n-bit (up to 16
bits) digital output.
Acknowledge
When the part is programmed for Infrared (IR) sensing, the IR
light wavelength within the “IR Sensing” spectral response curve
in Figure 15 is converted into current. With ADC, the current is
converted to an unsigned n-bit (up to 16 bits) digital output.
An Acknowledge (ACK) is a software convention used to indicate
a successful data transfer. The transmitting device releases the
SDA bus after transmitting 8 bits. During the ninth clock cycle,
the receiver pulls the SDA line LOW to acknowledge the reception
of the 8 bits of data (refer to Figure 12). The ISL29035 responds
with an ACK after recognition of a START condition followed by a
FN8371 Rev 3.00
December 12, 2016
Page 8 of 17
ISL29035
valid Identification Byte, and once again, after successful receipt
of an Address Byte. The ISL29035 also responds with an ACK
after receiving a Data byte of a write operation. The master must
respond with an ACK after receiving a Data byte of a read
operation.
Write Operation
BYTE WRITE
In a byte write operation, the ISL29035 requires the Device
Address byte, Register Address byte and the Data byte. The
master starts the communication with a START condition. Upon
receipt of the Device Address byte, Register Address byte and the
Data byte, the ISL29035 responds with an Acknowledge (ACK).
Following the ISL29035 data acknowledge response, the master
terminates the transfer by generating a STOP condition. The
ISL29035 then begins an internal write cycle of the data to the
volatile memory. During the internal write cycle, the device inputs
are disabled and the SDA line is in a high impedance state, so
the device will not respond to any requests from the master (refer
to Figure 11).
Device Addressing
Following a START condition, the master must output a Device
Address byte. The 7 MSBs of the Device Address byte are known
as the device identifier. The device identifier bits of the ISL29035
are internally hard-wired as “1000100”. The LSB of the Device
Address byte is defined as a Read or Write (R/W) bit. When this
R/W bit is a “1”, a read operation is selected and when “0”, a write
operation is selected (refer to Figure 10). The master generates a
START condition followed by Device Address byte 1000100x (x as
R/W) and the ISL29035 compares it with the internal device
identifier. Upon a correct comparison, the device outputs an
acknowledge (LOW) on the SDA line (refer to Figure 12).
BURST WRITE
The ISL29035 has a burst write operation, which allows the
master to write multiple consecutive bytes from a specific
address location. It is initiated in the same manner as the byte
write operation, but instead of terminating the write cycle after
the first Data byte is transferred, the master can write to the
whole register array. After the receipt of each byte, the ISL29035
responds with an acknowledge, and the address is internally
incremented by one. The address pointer remains at the last
address byte written. When the counter reaches the end of the
register address list, it “rolls over” and goes back to the first
Register Address.
DEVICE
ADDRESS BYTE
1
0
0
0
1
0
0
R/W
A0
REGISTER
ADDRESS BYTE
A7 A6 A5 A4 A3
D7 D6 D5 D4 D3
A2 A1
D2 D1
D0 DATA BYTE
FIGURE 10. DEVICE ADDRESS, REGISTER ADDRESS AND DATA BYTE
S
T
A
R
T
S
T
O
P
SIGNAL FROM
MASTER DEVICE
DEVICE ADDRESS
BYTE
ADDRESS BYTE
DATA BYTE
1 0 0 0 1 0 0 0
SIGNAL AT SDA
A
C
K
A
C
K
A
C
K
SIGNALS FROM
SLAVE DEVICE
FIGURE 11. BYTE WRITE SEQUENCE
8th
CLK
9th
CLK
SCL FROM
MASTER
HIGH
IMPEDANCE
SDA FROM
TRANSMITTER
SDA FROM
RECEIVER
DATA
STABLE
DATA
STABLE CHANGE
DATA
ACK
STOP
START
FIGURE 12. START, DATA STABLE, ACKNOWLEDGE AND STOP CONDITION
FN8371 Rev 3.00
December 12, 2016
Page 9 of 17
ISL29035
an acknowledge but issuing a STOP condition (refer to
Figure 14).
Read Operation
The ISL29035 has two basic read operations: Byte Read and
Burst Read.
For more information about the I2C standard, please consult the
Phillips™ I2C specification documents.
BYTE READ
Byte read operations allow the master to access any register
location in the ISL29035. The Byte read operation is a two step
process. The master issues the START condition and the Device
Address byte with the R/W bit set to “0”, receives an
acknowledge, then issues the Register Address byte. After
acknowledging receipt of the register address byte, the master
immediately issues another START condition and the Device
Address byte with the R/W bit set to “1”. This is followed by an
acknowledge from the device and then by the 8-bit data word.
The master terminates the read operation by not responding with
an acknowledge and then issuing a stop condition (refer to
Figure 13).
Power-On Reset
The Power-On Reset (POR) circuitry protects the internal logic
against powering up in the incorrect state. The ISL29035 will
power up into Standby mode after VDD exceeds the POR trigger
level and will power down into Reset mode when VDD drops
below the POR trigger level. This bidirectional POR feature
protects the device against ‘brown-out’ failure following a
temporary loss of power.
The POR is an important feature because it prevents the
ISL29035 from starting to operate with insufficient voltage, prior
to stabilization of the internal bandgap. The ISL29035 prevents
communication to its registers and greatly reduces the likelihood
of data corruption on power-up.
BURST READ
Burst read operation is identical to the Byte Read operation.
After the first Data byte is transmitted, the master now responds
with an acknowledge, indicating it requires additional data. The
device continues to output data for each acknowledge received.
The master terminates the read operation by not responding with
S
T
A
R
T
S
S
T
O
P
T
A
R
T
DEVICE ADDRESS
WRITE
DEVICE ADDRESS
READ
SIGNAL FROM
MASTER DEVICE
ADDRESS BYTE
DATA BYTE
1 0 0 0 1 0 0 0
1 0 0 0 1 0 0 1
SIGNAL AT SDA
A
C
K
A
C
K
A
C
K
SIGNALS FROM
SLAVE DEVICE
FIGURE 13. BYTE ADDRESS READ SEQUENCE
S
T
A
R
T
S
T
A
R
T
S
T
O
P
DEVICE ADDRESS
WRITE
DEVICE
ADDRESS READ
SIGNAL FROM
MASTER DEVICE
ADDRESS BYTE
DATA BYTE 1
DATA BYTE 2
DATA BYTE n
1 0 0 0 1 0 0 0
1 0 0 0 1 0 0 1
SIGNAL AT SDA
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
SIGNALS FROM
SLAVE DEVICE
[(n) is any integer
greater than 1]
FIGURE 14. BURST READ SEQUENCE
FN8371 Rev 3.00
December 12, 2016
Page 10 of 17
ISL29035
TABLE 2. REGISTER MAP
REGISTER BITS
REGISTER
ADDRESS
NAME
COMMAND-I
COMMAND-II
DATALSB
DEC
HEX
B7
B6
B5
B4
B3
B2
INT
B1
B0
DEFAULT ACCESS
0
1
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x0F
OP2
OP1
OP0
RESERVED
PRST1
PRST0
0x00
0x00
RW
RW
RO
RESERVED
RES1
D3
RES0
D2
RANGE1 RANGE0
2
D7
D15
TL7
D6
D14
D5
D13
TL5
TL13
TH5
TH13
1
D4
D12
TL4
TL12
TH4
TH12
0
D1
D9
D0
D8
0x00
DATAMSB
3
D11
TL3
TL11
TH3
TH11
1
D10
TL2
0x00
RO
INT_LT_LSB
INT_LT_MSB
INT_HT_LSB
INT_HT_MSB
ID
4
TL6
TL1
TL0
TL8
TH0
TH8
0x00
RW
RW
RW
RW
RW
5
TL15
TH7
TL14
TL10
TH2
TH10
TL9
0x00
6
TH6
TH1
0xFF
7
TH15
BOUT
TH14
RESERVED
TH9
0xFF
15
RESERVED
1x101xxx
INTERRUPT PERSIST BITS (B0-B1)
Register Description
The interrupt persist bits provide control over when interrupts
occur. There are four different selections for this feature. A value
of n (where n is 1, 4, 8, and 16) results in an interrupt only if the
value remains outside the threshold window for n consecutive
integration cycles. For example, if n is equal to 16 and the ADC
resolution is set to 16-bits, then the integration time is 105ms.
An interrupt is generated whenever the last conversion results in
a value outside of the programmed threshold window. The
interrupt is active-low and remains asserted until cleared by
writing the COMMAND register with the CLEAR bit set. Table 5
lists the possible interrupt persist bits.
Following are detailed descriptions of the control registers
related to the operation of the ISL29035 ambient light sensor
device. These registers are accessed by the I2C serial interface.
For details on the I2C interface, refer to “Serial Interface” on
page 8.
All the features of the device are controlled by the registers. The
ADC data can also be read. The following sections explain the
details of each register bit. All RESERVED bits are Intersil used
bits ONLY. The value of the reserved bit can change without
notice.
TABLE 5. INTERRUPT PERSIST BITS
Decimal to Hexadecimal Conversion
NUMBER OF INTEGRATION
To convert decimal value to hexadecimal value, divide the
decimal number by 16 and write the remainder on the side as
the least significant digit. This process is continued by dividing
the quotient by 16 and writing the remainder until the quotient
is 0. When performing the division, the remainders, which will
represent the hexadecimal equivalent of the decimal number,
are written beginning with the least significant digit (right) and
each new digit is written to the next most significant digit (the
left) of the previous digit. Consider the number 175 decimal.
B1
0
B0
0
CYCLES (n)
1
4
0
1
1
0
8
1
1
16
INTERRUPT STATUS BIT (B2)
TABLE 3. DECIMAL TO HEXADECIMAL
The interrupt status bit (INT) is a status bit for light intensity
detection. The bit is set to logic HIGH when the light intensity
crosses the interrupt thresholds window (register address
0x04 - 0x07), and set to logic LOW when it is within the interrupt
thresholds window. Once the interrupt is triggered, the INT pin
goes low and the interrupt status bit goes HIGH until the status
bit is polled through the I2C read command. Both the INT pin and
the interrupt status bit are automatically cleared at the end of
the 8-bit Device Register byte (0x00) transfer. Table 6 shows the
interrupt status states.
DIVISION
175/16
QUOTIENT
10 = A
REMAINDER
15 = F
HEX NUMBER
0xAF
Command-I Register (Address: 0x00)
TABLE 4. COMMAND-I REGISTER ADDRESS
REGISTER BITS
ADDR
(HEX) B7 B6 B5 B4 B3 B2 B1
DFLT
B0 (HEX)
NAME
TABLE 6. INTERRUPT STATUS BIT (INT)
COMMAND-I 0x00 OP OP OP RESERVED INT PRST PRST 0x00
2
1
0
1
0
BIT 2
OPERATION
Interrupt is cleared or not triggered yet
Interrupt is triggered
0
1
The Command-I register consists of control and status bits. In
this register, there are two interrupt persist bits, one interrupt
status bit and three operation mode bits. The operation mode
bits and the interrupt persist bits are independent of each other.
The default register value is 0x00 at power-on.
FN8371 Rev 3.00
December 12, 2016
Page 11 of 17
ISL29035
changes the integration time, which is the period the device’s
Analog-to-Digital (A/D) converter samples the photodiode current
signal for a measurement. Table 10 lists the possible ADC
resolution. Only 16-bit ADC resolution can reject better 50/60Hz
noise flickering light source.
OPERATION MODE BITS (B5-B7)
The ISL29035 has different operating modes. These modes are
selected by setting B5 - B7 bits on register address 0x00. The
device powers up on a disable mode. Table 7 lists the possible
operating modes.
TABLE 10. ADC RESOLUTION DATA WIDTH
TABLE 7. OPERATING MODES BITS
B3
0
B2
0
NUMBER OF CLOCK CYCLES
216 = 65,536
n-BIT ADC
B7 B6 B5
OPERATION
Power-down the device (default)
16
12
8
0
0
0
0
0
1
0
1
212 = 4,096
The device measures ALS only once every integration cycle.
This is the lowest operating mode. (Note 11)
1
0
28 = 256
4 = 16
4
0
1
1
0
0
1
1
0
1
0
1
0
1
IR once
1
1
2
0
Reserved (Do Not Use)
Reserved (Do Not Use)
Measures ALS continuously
Measures IR continuous
Reserved (Do Not Use)
Integration Time
1
1
1
TABLE 11. INTEGRATION TIME OF n-BIT ADC
n # ADC BITS
INTEGRATION TIME (ms)
1
4
8
0.0256
0.41
6.5
NOTE:
11. Intersil does not recommend using this mode.
12
16
105
Command-II Register (Address: 0x01)
TABLE 8. COMMAND-II REGISTER BITS
REGISTER BITS
Data Registers (Addresses: 0x02 and 0x03)
TABLE 12. ADC REGISTER BITS
REGISTER BITS
ADDR
(HEX)
B
7
B
6
B
5
B
4
DFLT
(HEX)
NAME
B3
B2
B1
B0
ADDR
DFLT
NAME
(HEX) B7 B6 B5 B4 B3 B2 B1 B0 (HEX)
COMMAND-II 0x01 RESERVED RES RES RANGE RANGE 0x00
1
0
1
0
DATALSB 0x02 D7 D6 D5 D4 D3 D2 D1 D0 0x00
DATAMSB 0x03 D15 D14 D13 D12 D11 D10 D9 D8 0x00
The Command-II register consists of ADC control bits. In this
register, there are two range bits and two ADC resolution bits.
The default register value is 0x00 at power-on.
The ISL29035 has two 8-bit read-only registers to hold the upper
and lower byte of the ADC value. The upper byte is accessed at
address 0x03 and the lower byte is accessed at address 0x02.
For 16-bit resolution, the data is from D0 to D15; for 12-bit
resolution, the data is from D0 to D11; for 8-bit resolution, the
data is from D0 to D7 and for 4-bit resolution, the data is from D0
to D3. The registers are refreshed after every conversion cycle.
The default register value is 0x00 at power-on.
FULL SCALE LUX RANGE (B0-B1)
The full scale Lux range has four different selectable ranges. The
range determines the full scale Lux range (1k, 4k, 16k and 64k).
Each range has a maximum allowable Lux value. Lower range
values offer better resolution. Table 9 lists the possible values
of Lux.
TABLE 13. ADC DATA REGISTERS
TABLE 9. RANGE REGISTER BITS
FULL SCALE LUX RANGE
ADDRESS
(HEX)
0x02
CONTENTS
RANGE SELECTION
B1
B0
(Lux)
1,000
4,000
16,000
64,000
D0 is LSB for 4-, 8-, 12- or 16-bit resolution; D3 is MSB for
4-bit resolution; D7 is MSB for 8-bit resolution
0
1
2
3
0
0
0x03
D15 is MSB for 16-bit resolution; D11 is MSB for 12-bit
resolution
0
1
1
0
1
1
ADC RESOLUTION (B3-B2)
B2 and B3 determine the ADC’s resolution and the number of
clock cycles per conversion. Changing the number of clock cycles
does more than just change the resolution of the device; it also
FN8371 Rev 3.00
December 12, 2016
Page 12 of 17
ISL29035
software should mask the Bit0-Bit2 and Bit6-Bit7 to properly
identify the device.
Lower Interrupt Threshold Registers
(Address: 0x04 and 0x05)
DEVICE ID BITS (B3-B5)
TABLE 14. INTERRUPT REGISTER BITS
The ISL29035 provides 3 bits to identify the device in a system.
These bits are located on register address 0x0F, Bit3–Bit5. The
identification bit value for the ISL29035 is xx101xxx. The device
identification bits are read only bits. It is important to notice that
Bit7 is a status bit for Brownout condition (BOUT).
REGISTER BITS
ADDR
(HEX) B7 B6 B5 B4 B3 B2 B1 B0 (HEX)
DFLT
NAME
INT_LT_LSB 0x04 TL7 TL6 TL5 TL4 TL3 TL2 TL1 TL0 0x00
INT_LT_MSB 0x05 TL1 TL1 TL1 TL1 TL1 TL1 TL9 TL8 0x00
5
4
3
2
1
0
BROWNOUT STATUS BIT - BOUT (B7)
Bit7 on register address 0x0F is a status bit for Brownout
condition (BOUT). The default value of this bit is “BOUT = 1”
during the initial power-up, which indicates the device may
possibly have gone through a brownout condition. Therefore, the
status bit should be reset to “BOUT = 0” by an I2C write command
during the initial configuration of the device.
The lower interrupt threshold registers are used to set the lower
trigger point for interrupt generation. If the ALS value crosses
below or is equal to the lower threshold, an interrupt is asserted
on the interrupt pin and the interrupt status. Registers
INT_LT_LSB (0x04) and INT_LT_MSB (0x05) provide the LOW and
HIGH bytes, respectively, of the lower interrupt threshold. The
HIGH and LOW bytes from each set of registers are combined to
form a 16-bit threshold value. The interrupt threshold registers
default to 0x00 upon power-up.
The default register value is 0xA8 at power-on.
Applications Information
Figure 15 is a normalized spectral response of various types of
light sources for reference.
Upper Interrupt Threshold Registers
(Address: 0x06 and 0x07)
1.0
TABLE 15. INTERRUPT REGISTER BITS
REGISTER BITS
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
FLUORESCENT
ADDR
DFLT
NAME
(HEX) B7 B6 B5 B4 B3 B2 B1 B0 (HEX)
INT_HT_LSB 0x06 TH7 TH6 TH5 TH4 TH3 TH2 TH1 TH0 0xFF
INT_HT_MSB 0x07 TH1 TH1 TH1 TH1 TH1 TH1 TH9 TH8 0xFF
HALOGEN
INCAND.
SUN
5
4
3
2
1
0
The upper interrupt threshold registers are used to set the upper
trigger point for interrupt generation. If the ALS value crosses
above or is equal to the upper threshold, an interrupt is asserted
on the interrupt pin and the interrupt status. Registers
INT_HT_LSB (0x06) and INT_HT_MSB (0x07) provide the LOW
and HIGH bytes, respectively, of the upper interrupt threshold.
The HIGH and LOW bytes from each set of registers are combined
to form a 16-bit threshold value. The interrupt threshold registers
default to 0xFF on power-up.
350
550
750
950
WAVELENGTH (nm)
FIGURE 15. NORMALIZED SPECTRAL RESPONSE OF LIGHT SOURCES
Calculating Lux
The ISL29035’s ADC output codes, DATA, are directly
proportional to Lux in the ambient light sensing.
ID Register (Address: 0x0F)
(EQ. 1)
TABLE 16. ID REGISTER BITS
E
= DATA
cal
REGISTER BITS
ADDR
Where Ecal is the calculated Lux reading. The constant is
determined by the full-scale range and the ADC’s maximum
output counts. The constant is independent of the light sources
(fluorescent, incandescent and sunlight) because the light
sources’ IR component is removed during the light signal
process. The constant can also be viewed as the sensitivity (the
smallest Lux measurement the device can measure).
NAME (HEX) B7
B6
B5 B4 B3 B2 B1 B0
DFLT
ID 0x0F BOUT RESERVED
1
0
1
RESERVED 1x101xxx
The ID register has three different types of information, which is
discussed in the following.
RESERVED BITS (B0-B2 AND B6)
Range
Count
max
(EQ. 2)
----------------------------
=
All RESERVED bits on the ISL29035 are Intersil used bits only.
Bit0-Bit2 and Bit6 are RESERVED bits where their value might
change without any notification to the user. It is advised when
using the identification bits to identify the device in a system, the
Where Range is defined in Table 9 on page 12. Countmax is the
maximum output counts from the ADC.
FN8371 Rev 3.00
December 12, 2016
Page 13 of 17
ISL29035
The transfer function used for n-bits ADC becomes Equation 3:
Board Mounting Considerations
Range
For applications requiring the light measurement, the board
mounting location should be reviewed. The device uses an
Optical Dual Flat Pack No Lead (ODFN) package, which subjects
the die to mild stresses when the Printed Circuit (PC) board is
heated and cooled, which slightly changes the shape. Because of
these die stresses, placing the device in areas subject to slight
twisting can cause degradation of reference voltage accuracy. It
is normally best to place the device near the edge of a board, or
on the shortest side, because the axis of bending is most limited
in that location.
(EQ. 3)
------------------
E
=
DATA
cal
n
2
Where n = 4, 8, 12 or 16. This is the number of ADC bits
programmed in the command register. 2n represents the
maximum number of counts possible from the ADC output. Data is
the ADC output stored in the data registers (02 hex and 03 hex).
Enhancing EV Accuracy
The device has an on-chip passive optical filter designed to block
(reject) most of the incident Infrared. However, EV measurement
may vary under differing IR-content light sources. In order to
optimize the measurement variation between differing
IR-content light sources, ISL29035 provides IR channel, which is
programmed at COMMAND-I (Reg0x0) to measure the IR level of
differing IR-content light sources.
Layout Considerations
The ISL29035 is relatively insensitive to layout. Like other I2C
devices, it is intended to provide excellent performance even in
significantly noisy environments. There are only a few
considerations that will ensure best performance.
Route the supply and I2C traces as far as possible from all
sources of noise. Use two power-supply decoupling capacitors,
1µF and 0.1µF, placed close to the device.
The ISL29035’s ADC output codes, DATA, are directly
proportional to the IR intensity received in the IR sensing.
DATA = E
(EQ. 4)
(EQ. 5)
IR
IR
Soldering Considerations
Then EVAccuracy can be found in Equation 5:
Convection heating is recommended for reflow soldering; direct
infrared heating is not recommended. The plastic ODFN package
does not require a custom reflow soldering profile, and is
qualified to +260°C. A standard reflow soldering profile with a
+260°C maximum is recommended.
EV
= KxDATA
+ DATA
EV IR
Accuracy
Where DATAEV is the received ambient light intensity ADC output
codes. K is a resolution of visible portion. Its unit is Lux/count.
The typical value of K is 0.82. DATAIR is the received IR intensity.
The constant changes with the spectrum of background IR,
such as A, F2 and D65. The also changes with the ADC’s range
and resolution selections. A typical for Range1 and Range2 is
-11292.86 and for Range3 and Range4 it is 2137.14 without IR
tinted glass.
Typical Circuit
A typical application for the ISL29035 is shown in Figure 16 on
page 15. The ISL29035’s I2C address is internally hard-wired as
1000100. The device can be tied onto a system’s I2C bus,
together with other I2C compliant devices.
Noise Rejection
Electrical AC power worldwide is distributed at either 50Hz or
60Hz. Artificial light sources vary in intensity at the AC power
frequencies. The undesired interference frequencies are infused
on the electrical signals. This variation is one of the main sources
of noise for the light sensors. Integrating type ADC’s have
excellent noise-rejection characteristics for periodic noise
sources whose frequency is an integer multiple of the conversion
rate. By setting the sensor’s integration time to an integer
multiple of periodic noise signal, the performance of an ambient
light sensor can be improved greatly in the presence of noise. In
order to reject the AC noise, the integration time of the sensor
must be adjusted to match the AC noise cycle. For instance, a
60Hz AC unwanted signal’s sum from 0ms to k*16.66ms
(k = 1,2...ki) is zero. Similarly, setting the device’s integration
time to be an integer multiple of the periodic noise signal, greatly
improves the light sensor output signal in the presence of noise.
Suggested PCB Footprint
It is important that users check the TB477, “Surface Mount
Assembly Guidelines for Optical Dual Flat Pack No Lead (ODFN)
Package” before starting ODFN product board mounting.
FN8371 Rev 3.00
December 12, 2016
Page 14 of 17
ISL29035
100
VDD_PULLUP
4.7k 4.7k 4.7k
VDD
1µF
1
VDD
SDA
SCL
SDA
6
5
4
SCL
INT
3
ISL29035
NC
MCU
SENSOR
GPIO
GND
2
FIGURE 16. ISL29035 TYPICAL CIRCUIT
FIGURE 17. 6 LD ODFN SENSOR LOCATION OUTLINE
© Copyright Intersil Americas LLC 2013-2016 All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8371 Rev 3.00
December 12, 2016
Page 15 of 17
ISL29035
Revision History The revision history provided is for informational purposes only and is believed to be accurate, however, not
warranted. Please go to web to make sure you have the latest revision.
DATE
REVISION
CHANGE
December 12, 2016 FN8371.3 Updated related literature on page 1.
Added Table 1 on page 1.
Added Note 6 on page 4 and referenced it in EC table.
Removed Note 7 on page 3.
Updated y-axis titles and added labels of Figures 7, 8 and 9. Updated title of Figure 9 (removed under F2 light
source) on page 7.
December 24, 2015 FN8371.2 Removed sections “Digital Inputs and Termination” and “Temperature Coefficient” from “Applications Information”
on page 13.
Added Related Literature on page 1
Updated Ordering Information table on page 3 by adding T&R quantity column and adding T7A part
Removed IR sensing from Figure 6 on page 7 and from “Photodiodes and ADC” on page 8
Removed 4 notes that were unrelated from Electrical Specifications table on page 4 and removed note referencing
removed notes from paragraph after Equation 5 on page 14.
Updated POD L6.1.5x1.6 to most current revision with rev change listed as follows:
Tiebar Note updated
From: Tiebar shown (if present) is a non-functional feature.
To: Tiebar shown (if present) is a non-functional feature and may be located on any of the 4 sides (or ends).
November 12, 2014 FN8371.1 On page 1 updated: 90ms to 105ms and changed Shutdown current from 0.3 to 0.51 and corrected the Labels on
Figure 2.
Updated the Ordering Information on page 3.
On page 3 updated pin configuration to show that Pin 1 is the longest pin.
In “Electrical Specifications” on page 4 updated:
- “Light Source Variation” to “Part-to-part Variation”.
- test conditions for %/Value, ADCR0, ADCR1,ADCR2, ADCR3, ADC_IRR0, ADC_IRR1,ADC_IRR2, and ADC_IRR3
On page 7 corrected the labels on Figure 6.
On page 8 updated:
- under Photodiodes and ADC section Figure reference, changed from 100ms to 105ms, changed from Range 1 to
Range 0.
On page 11 under Interrupt Persist Bits (B0-B1) section, updated from 100ms to 105ms
On page 12 added note for Table 7 and verbiage under ADC Resolution (B3-B2) section
On page 14 updated the Temperature Coefficient section.
September 18, 2013 FN8371.0 Initial Release.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
FN8371 Rev 3.00
December 12, 2016
Page 16 of 17
ISL29035
For the most recent package outline drawing, see L6.1.5x1.6.
Package Outline Drawing
L6.1.5x1.6
6 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN)
Rev 1, 4/15
1.50
0.55
PIN #1 INDEX AREA
6
PIN 1
0.50
1.60
(2X)
0.10
0.10 M C A B
0.25
4
TOP VIEW
0.40
0.70
BOTTOM VIEW
2.00
0.18
SEE DETAIL "X"
0.80
0.10 C
C
0.70 ± 0.05
BASE PLANE
0.50
SEATING PLANE
0.08 C
SIDE VIEW
0.25
PACKAGE
OUTLINE
0.25
5
C
0 . 2 REF
0.70
0.65
0 . 00 MIN.
0 . 05 MAX.
TYPICAL RECOMMENDED LAND PATTERN
DETAIL “X”
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to ASME Y14.5m-1994.
3.
4.
Unless otherwise specified, tolerance : Decimal ± 0.05
Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature and may
be located on any of the 4 sides (or ends)..
5.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN8371 Rev 3.00
December 12, 2016
Page 17 of 17
相关型号：
ISL29038IROZ-EVALZ
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
INTERSIL
ISL29038IROZ-EVALZ
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
XICOR
ISL29038IROZ-EVALZ
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
RENESAS
ISL29038IROZ-T7
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
INTERSIL
ISL29038IROZ-T7
Low Power Ambient Light and Proximity Sensor with Enhanced Infrared Rejection
RENESAS
©2020 ICPDF网 联系我们和版权申明