ISL6613 [RENESAS]
Advanced Synchronous Rectified Buck MOSFET Drivers with Protection Features;型号: | ISL6613 |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | Advanced Synchronous Rectified Buck MOSFET Drivers with Protection Features |
文件: | 总12页 (文件大小:601K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATASHEET
ISL6612, ISL6613
Advanced Synchronous Rectified Buck MOSFET Drivers with Protection Features
FN9153
Rev 9.00
June 15, 2010
The ISL6612 and ISL6613 are high frequency MOSFET
drivers specifically designed to drive upper and lower power
Features
• Pin-to-pin Compatible with HIP6601 SOIC family for Better
Performance and Extra Protection Features
N-Channel MOSFETs in a synchronous rectified buck
converter topology. These drivers combined with HIP63xx or
ISL65xx Multi-Phase Buck PWM controllers and N-Channel
MOSFETs form complete core-voltage regulator solutions for
advanced microprocessors.
• Dual MOSFET Drives for Synchronous Rectified Bridge
• Advanced Adaptive Zero Shoot-Through Protection
- Body Diode Detection
The ISL6612 drives the upper gate to 12V, while the lower
gate can be independently driven over a range from 5V to
12V. The ISL6613 drives both upper and lower gates over a
range of 5V to 12V. This drive-voltage provides the flexibility
necessary to optimize applications involving trade-offs
between gate charge and conduction losses.
- Auto-zero of r
DS(ON)
Conduction Offset Effect
• Adjustable Gate Voltage (5V to 12V) for Optimal Efficiency
• 36V Internal Bootstrap Schottky Diode
• Bootstrap Capacitor Overcharging Prevention
• Supports High Switching Frequency (up to 2MHz)
- 3A Sinking Current Capability
An advanced adaptive zero shoot-through protection is
integrated to prevent both the upper and lower MOSFETs from
conducting simultaneously and to minimize the dead time.
These products add an overvoltage protection feature
operational before VCC exceeds its turn-on threshold, at which
the PHASE node is connected to the gate of the low side
MOSFET (LGATE). The output voltage of the converter is then
limited by the threshold of the low side MOSFET, which
provides some protection to the microprocessor if the upper
MOSFET(s) is shorted during startup. The over-temperature
protection feature prevents failures resulting from excessive
power dissipation by shutting off the outputs when its junction
temperature exceeds +150°C (typically). The driver resets once
its junction temperature returns to +108°C (typically).
- Fast Rise/Fall Times and Low Propagation Delays
• Three-State PWM Input for Output Stage Shutdown
• Three-State PWM Input Hysteresis for Applications With
Power Sequencing Requirement
• Pre-POR Overvoltage Protection
• VCC Undervoltage Protection
• Over Temperature Protection (OTP) with +42°C
Hysteresis
• Expandable Bottom Copper Pad for Enhanced Heat
Sinking
• Dual Flat No-Lead (DFN) Package
These drivers also feature a three-state PWM input which,
working together with Intersil’s multi-phase PWM controllers,
prevents a negative transient on the output voltage when the
output is shut down. This feature eliminates the Schottky
diode that is used in some systems for protecting the load
from reversed output voltage events.
- Near Chip-Scale Package Footprint; Improves PCB
Efficiency and Thinner in Profile
• Pb-Free Available (RoHS Compliant)
Applications
• Core Regulators for Intel® and AMD® Microprocessors
• High Current DC/DC Converters
• High Frequency and High Efficiency VRM and VRD
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
• Technical Brief TB417 for Power Train Design, Layout
Guidelines, and Feedback Compensation Design
FN9153 Rev 9.00
June 15, 2010
Page 1 of 12
ISL6612, ISL6613
Ordering Information
PART
NUMBER
PART
MARKING
TEMP. RANGE
(°C)
PKG.
DWG. #
PACKAGE
8 Ld SOIC (Pb-Free)
ISL6612CBZ (Note 2)
6612 CBZ
6612 CBZ
6612 CBZ
0 to +85
0 to +85
M8.15
M8.15
M8.15
M8.15
ISL6612CBZ-T (Notes 1, 2)
ISL6612CBZA (Note 2)
8 Ld SOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
8 Ld EPSOIC
0 to +85
ISL6612CBZA-T (Notes 1, 2) 6612 CBZ
0 to +85
ISL6612CRZ (Note 2)
612Z
0 to +85
L10.3x3
L10.3x3
M8.15B
M8.15B
M8.15B
M8.15B
M8.15B
M8.15
ISL6612CRZ-T (Notes 1, 2)
ISL6612ECB-T (Note 1)
ISL6612ECBZ (Note 2)
612Z
0 to +85
ISL66 12ECB
6612 ECBZ
0 to +85
0 to +85
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
8 Ld SOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld EPSOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
8 Ld SOIC (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
10 Ld 3x3 DFN (Pb-Free)
ISL6612ECBZ-T (Notes 1, 2) 6612 ECBZ
0 to +85
ISL6612EIBZ (Note 2)
ISL6612EIBZ-T (Notes 1, 2)
ISL6612IBZ (Note 2)
6612 EIBZ
6612 EIBZ
6612 IBZ
6612 IBZ
12IZ
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
0 to +85
ISL6612IBZ-T (Notes 1, 2)
ISL6612IRZ (Note 2)
M8.15
L10.3x3
L10.3x3
M8.15
ISL6612IRZ-T (Notes 1, 2)
ISL6613CBZ (Note 2)
12IZ
6613 CBZ
6613 CBZ
613Z
ISL6613CBZ-T (Notes 1, 2)
ISL6613CRZ (Note 2)
0 to +85
M8.15
0 to +85
L10.3x3
L10.3x3
M8.15B
M8.15B
M8.15B
M8.15B
M8.15
ISL6613CRZ-T (Notes 1, 2)
ISL6613ECBZ (Note 2)
613Z
0 to +85
6613 ECBZ
0 to +85
ISL6613ECBZ-T (Notes 1, 2) 6613 ECBZ
0 to +85
ISL6613EIBZ (Note 2)
ISL6613EIBZ-T (Notes 1, 2)
ISL6613IBZ (Note 2)
ISL6613IBZ-T (Notes 1, 2)
ISL6613IRZ (Note 2)
ISL6613IRZ-T (Notes 1, 2)
NOTES:
6613 EIBZ
6613 EIBZ
6613 IBZ
6613 IBZ
13IZ
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
M8.15
L10.3x3
L10.3x3
13IZ
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-
020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6612, ISL6613. For more information on MSL please see
techbrief TB363.
FN9153 Rev 9.00
June 15, 2010
Page 2 of 12
ISL6612, ISL6613
Pinouts
ISL6612CB, ISL6613CB
(8 LD SOIC)
ISL6612ECB, ISL6613ECB
(8 LD EPSOIC)
ISL6612CR, ISL6613CR
(10 LD 3x3 DFN)
TOP VIEW
TOP VIEW
UGATE
BOOT
PWM
1
2
3
4
8
7
6
5
PHASE
PVCC
VCC
1
2
3
4
5
10
9
UGATE
BOOT
PHASE
PVCC
N/C
GND
GND
8
N/C
PWM
7
VCC
GND
LGATE
6
GND
LGATE
Block Diagram
ISL6612 AND ISL6613
UVCC
BOOT
VCC
UGATE
OTP AND
PRE-POR OVP
FEATURES
+5V
PHASE
PVCC
SHOOT-
THROUGH
(LVCC)
10k
PROTECTION
UVCC = VCC FOR ISL6612
UVCC = PVCC FOR ISL6613
POR/
CONTROL
LOGIC
PWM
LGATE
GND
8k
FOR DFN AND EPSOIC-DEVICES, THE PAD ON THE BOTTOM SIDE OF
THE PACKAGE MUST BE SOLDERED TO THE CIRCUIT’S GROUND.
PAD
FN9153 Rev 9.00
June 15, 2010
Page 3 of 12
ISL6612, ISL6613
Typical Application - 3 Channel Converter Using ISL65xx and ISL6612 Gate Drivers
+12V
+5V TO 12V
BOOT
UGATE
VCC
PVCC
PWM
PHASE
LGATE
ISL6612
GND
+12V
+5V TO 12V
+5V
+V
CORE
VCC
BOOT
VCC
VFB
COMP
PWM1
UGATE
PHASE
PVCC
PWM
VSEN
ISL6612
PWM2
PWM3
PGOOD
LGATE
MAIN
GND
CONTROL
ISL65xx
VID
ISEN1
ISEN2
ISEN3
FS
+12V
+5V TO 12V
GND
BOOT
VCC
UGATE
PHASE
PVCC
ISL6612
PWM
LGATE
GND
FN9153 Rev 9.00
June 15, 2010
Page 4 of 12
ISL6612, ISL6613
Absolute Maximum Ratings
Thermal Information
Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
Supply Voltage (PVCC) . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.3V
Thermal Resistance
(°C/W)
(°C/W)
JC
JA
8 Ld SOIC Package (Note 4) . . . . . . . .
8 Ld EPSOIC Package (Notes 5, 6). . .
10 Ld DFN Package (Notes 5, 6). . . . .
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
100
50
48
N/A
7
7
Input Voltage (V
) . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to 7V
PWM
BOOT Voltage (V
). . . . . . . . . . . . . . . . . . . . . . . . . . . .36V
BOOT-GND
BOOT To PHASE Voltage (V
). . . . . -0.3V to 15V (DC)
BOOT-PHASE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 16V (<10ns, 10µJ)
UGATE. . . . . . . . . . . . . . . . . . . V
- 0.3V
to V
+ 0.3V
+ 0.3V
+ 0.3V
+ 0.3V
PHASE
DC
BOOT
BOOT
PVCC
PVCC
V
- 3.5V (<100ns Pulse Width, 2µJ) to V
PHASE
LGATE . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V
to V
DC
GND - 5V (<100ns Pulse Width, 2µJ) to V
Recommended Operating Conditions
PHASE. . . . . . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3VDC to 24VDC
Ambient Temperature Range. . . . . . . . . . . . . . . . . . .-40°C to +85°C
Maximum Operating Junction Temperature. . . . . . . . . . . . . +125°C
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V 10%
Supply Voltage Range, PVCC . . . . . . . . . . . . . . . . 5V to 12V 10%
GND - 8V (<400ns, 20µJ) to 31V (<200ns, V < 36V)
ESD Rating
Human Body Model . . . . . . . . . . . . . . . . . . . . Class I JEDEC STD
BOOT-GND
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
4. is measured with the component mounted on a high effective thermal conductivity test board in free air.
JA
5. is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
JA
Tech Brief TB379.
6. For , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted.
MIN
MAX
PARAMETER
VCC SUPPLY CURRENT
SYMBOL
TEST CONDITIONS
(Note 8) TYP (Note 8) UNITS
Bias Supply Current
I
I
ISL6612, f
ISL6613, f
ISL6612, f
ISL6613, f
ISL6612, f
ISL6613, f
ISL6612, f
ISL6613, f
= 300kHz, V
= 300kHz, V
= 12V
= 12V
-
-
-
-
-
-
-
-
7.2
4.5
11
5
-
-
-
-
-
-
-
-
mA
mA
mA
mA
mA
mA
mA
mA
VCC
VCC
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
VCC
VCC
= 1MHz, V
= 1MHz, V
= 12V
VCC
VCC
= 12V
Gate Drive Bias Current
I
I
= 300kHz, V
= 300kHz, V
= 12V
2.5
5.2
7
PVCC
PVCC
PVCC
PVCC
= 12V
= 1MHz, V
= 12V
PVCC
PVCC
= 1MHz, V
= 12V
13
POWER-ON RESET AND ENABLE
VCC Rising Threshold
T
= 0°C to +85°C
= -40°C to +85°C
= 0°C to +85°C
T = -40°C to +85°C
A
9.35
8.35
7.35
6.35
9.80 10.00
9.80 10.00
V
V
V
V
A
VCC Rising Threshold
T
A
VCC Falling Threshold
T
7.60
7.60
8.00
8.00
A
VCC Falling Threshold
PWM INPUT (See “TIMING DIAGRAM” on page 7)
Input Current
I
V
V
= 5V
= 0V
-
450
-400
3.00
2.00
-
µA
µA
V
PWM
PWM
PWM
-
-
PWM Rising Threshold
VCC = 12V
VCC = 12V
VCC = 12V
VCC = 12V
VCC = 12V
VCC = 12V
VCC = 12V
-
-
PWM Falling Threshold
-
-
V
Typical Three-State Shutdown Window
Three-State Lower Gate Falling Threshold
Three-State Lower Gate Rising Threshold
Three-State Upper Gate Rising Threshold
Three-State Upper Gate Falling Threshold
1.80
2.40
V
-
-
-
-
1.50
1.00
3.20
2.60
-
-
-
-
V
V
V
V
FN9153 Rev 9.00
June 15, 2010
Page 5 of 12
ISL6612, ISL6613
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. (Continued)
MIN
MAX
PARAMETER
Shutdown Holdoff Time
SYMBOL
TEST CONDITIONS
(Note 8) TYP (Note 8) UNITS
t
-
-
-
-
-
-
-
-
-
-
245
26
18
18
12
10
10
10
10
10
-
-
-
-
-
-
-
-
-
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TSSHD
UGATE Rise Time
t
V
V
V
V
V
V
V
V
V
= 12V, 3nF Load, 10% to 90%
= 12V, 3nF Load, 10% to 90%
= 12V, 3nF Load, 90% to 10%
= 12V, 3nF Load, 90% to 10%
= 12V, 3nF Load, Adaptive
= 12V, 3nF Load, Adaptive
= 12V, 3nF Load
RU
PVCC
PVCC
PVCC
PVCC
PVCC
PVCC
PVCC
PVCC
PVCC
LGATE Rise Time
t
RL
UGATE Fall Time
t
FU
LGATE Fall Time
t
FL
UGATE Turn-On Propagation Delay (Note 7)
LGATE Turn-On Propagation Delay (Note 7)
UGATE Turn-Off Propagation Delay (Note 7)
LGATE Turn-Off Propagation Delay (Note 7)
LG/UG Three-State Propagation Delay (Note 7)
OUTPUT (Note 7)
t
PDHU
t
PDHL
PDLU
t
t
t
= 12V, 3nF Load
PDLL
= 12V, 3nF Load
PDTS
Upper Drive Source Current
Upper Drive Source Impedance
Upper Drive Sink Current
I
V
= 12V, 3nF Load
-
1.25
2.0
2
-
3.0
-
A
A
A
A
U_SOURCE
PVCC
R
150mA Source Current
1.25
U_SOURCE
I
V
= 12V, 3nF Load
PVCC
-
-
U_SINK
Upper Drive Transition Sink Impedance
Upper Drive DC Sink Impedance
Lower Drive Source Current
Lower Drive Source Impedance
Lower Drive Sink Current
R
70ns with Respect to PWM Falling
150mA Source Current
1.3
1.65
2
2.2
3.0
-
U_SINK_TR
U_SINK_DC
L_SOURCE
R
0.9
-
I
V
= 12V, 3nF Load
PVCC
R
150mA Source Current
0.85
-
1.25
3
2.2
-
L_SOURCE
I
V
= 12V, 3nF Load
L_SINK
PVCC
Lower Drive Sink Impedance
OVER TEMPERATURE SHUTDOWN
Thermal Shutdown Setpoint
Thermal Recovery Setpoint
NOTES:
R
150mA Sink Current
0.60
0.80
1.35
L_SINK
-
-
150
108
-
-
°C
°C
7. Limits should be considered typical and are not production tested.
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
Functional Pin Description
PACKAGE PIN #
PIN
SOIC
DFN
SYMBOL
FUNCTION
1
2
1
2
UGATE Upper gate drive output. Connect to gate of high-side power N-Channel MOSFET.
BOOT
Floating bootstrap supply pin for the upper gate drive. Connect the bootstrap capacitor between this pin and the
PHASE pin. The bootstrap capacitor provides the charge to turn on the upper MOSFET. See “Internal Bootstrap
Device” on page 8 for guidance in choosing the capacitor value.
-
3, 8
4
N/C
No Connection.
3
PWM
The PWM signal is the control input for the driver. The PWM signal can enter three distinct states during operation;
see “Three-State PWM Input” on page 7 for further details. Connect this pin to the PWM output of the controller.
4
5
6
7
5
6
7
9
GND
Bias and reference ground. All signals are referenced to this node. It is also the power ground return of the driver.
LGATE Lower gate drive output. Connect to gate of the low-side power N-Channel MOSFET.
VCC
Connect this pin to a +12V bias supply. Place a high quality low ESR ceramic capacitor from this pin to GND.
PVCC
This pin supplies power to both upper and lower gate drives in ISL6613; only the lower gate drive in ISL6612. Its
operating range is +5V to 12V. Place a high quality low ESR ceramic capacitor from this pin to GND.
8
9
10
11
PHASE Connect this pin to the SOURCE of the upper MOSFET and the DRAIN of the lower MOSFET. This pin provides
a return path for the upper gate drive.
PAD
Connect this pad to the power ground plane (GND) via thermally enhanced connection.
FN9153 Rev 9.00
June 15, 2010
Page 6 of 12
ISL6612, ISL6613
Description
1.5V<PWM<3.2V
1.0V<PWM<2.6V
PWM
t
t
PDLU
PDHU
t
TSSHD
t
PDTS
t
PDTS
t
FU
UGATE
LGATE
t
RU
t
t
FL
RL
t
t
TSSHD
PDLL
t
PDHL
FIGURE 1. TIMING DIAGRAM
Operation
Advanced Adaptive Zero Shoot-Through Deadtime
Control (Patent Pending)
Designed for versatility and speed, the ISL6612 and ISL6613
MOSFET drivers control both high-side and low-side
N-Channel FETs of a half-bridge power train from one
externally provided PWM signal.
These drivers incorporate a unique adaptive deadtime control
technique to minimize deadtime, resulting in high efficiency
from the reduced freewheeling time of the lower MOSFETs’
body-diode conduction, and to prevent the upper and lower
MOSFETs from conducting simultaneously. This is
accomplished by ensuring either rising gate turns on its
MOSFET with minimum and sufficient delay after the other
has turned off.
Prior to VCC exceeding its POR level, the Pre-POR
overvoltage protection function is activated; the upper gate
(UGATE) is held low and the lower gate (LGATE), controlled by
the Pre-POR overvoltage protection circuits, is connected to the
PHASE. Once the VCC voltage surpasses the VCC Rising
Threshold (see “Electrical Specifications” on page 5), the PWM
signal takes control of gate transitions. A rising edge on PWM
initiates the turn-off of the lower MOSFET (see Timing
During turn-off of the lower MOSFET, the PHASE voltage is
monitored until it reaches a -0.2V/+0.8V trip point for a
forward/reverse current, at which time the UGATE is released
Diagram). After a short propagation delay [t
], the lower
to rise. An auto-zero comparator is used to correct the r
PDLL
DS(ON)
gate begins to fall. Typical fall times [t ] are provided in
“Electrical Specifications” on page 5. Adaptive shoot-through
circuitry monitors the PHASE voltage and determines the upper
drop in the phase voltage preventing from false detection of the
-0.2V phase level during r conduction period. In the case
FL
DS(ON
of zero current, the UGATE is released after 35ns delay of the
LGATE dropping below 0.5V. During the phase detection, the
disturbance of LGATE’s falling transition on the PHASE node is
blanked out to prevent falsely tripping. Once the PHASE is
high, the advanced adaptive shoot-through circuitry monitors
the PHASE and UGATE voltages during a PWM falling edge
and the subsequent UGATE turn-off. If either the UGATE falls
to less than 1.75V above the PHASE or the PHASE falls to less
than +0.8V, the LGATE is released to turn on.
gate delay time [t
]. This prevents both the lower and
PDHU
upper MOSFETs from conducting simultaneously. Once this
delay period is complete, the upper gate drive begins to rise
[t ] and the upper MOSFET turns on.
RU
A falling transition on PWM results in the turn-off of the upper
MOSFET and the turn-on of the lower MOSFET. A short
propagation delay [t
] is encountered before the upper
PDLU
gate begins to fall [t ]. Again, the adaptive shoot-through
FU
circuitry determines the lower gate delay time, t
. The
Three-State PWM Input
PDHL
PHASE voltage and the UGATE voltage are monitored, and
the lower gate is allowed to rise after PHASE drops below a
level or the voltage of UGATE to PHASE reaches a level
depending upon the current direction (See the following
A unique feature of these drivers and other Intersil drivers is
the addition of a shutdown window to the PWM input. If the
PWM signal enters and remains within the shutdown window
for a set holdoff time, the driver outputs are disabled and
both MOSFET gates are pulled and held low. The shutdown
state is removed when the PWM signal moves outside the
shutdown window. Otherwise, the PWM rising and falling
thresholds (outlined in “Electrical Specifications” on page 5)
determine when the lower and upper gates are enabled.
section for details). The lower gate then rises [t ], turning on
RL
the lower MOSFET.
FN9153 Rev 9.00
June 15, 2010
Page 7 of 12
ISL6612, ISL6613
This feature helps prevent a negative transient on the output
voltage when the output is shut down, eliminating the
Schottky diode that is used in some systems for protecting
the load from reversed output voltage events.
As an example, suppose two IRLR7821 FETs are chosen as
the upper MOSFETs. The gate charge, Q , from the data
G
sheet is 10nC at 4.5V (V ) gate-source voltage. Then the
GS
Q
is calculated to be 53nC for UVCC (i.e. PVCC in
GATE
ISL6613, VCC in ISL6612) = 12V. We will assume a 200mV
droop in drive voltage over the PWM cycle. We find that a
bootstrap capacitance of at least 0.267µF is required.
1.6
In addition, more than 400mV hysteresis also incorporates
into the three-state shutdown window to eliminate PWM
input oscillations due to the capacitive load seen by the
PWM input through the body diode of the controller’s PWM
output when the power-up and/or power-down sequence of
bias supplies of the driver and PWM controller are required.
1.4
1.2
1.0
0.8
0.6
Power-On Reset (POR) Function
During initial startup, the VCC voltage rise is monitored.
Once the rising VCC voltage exceeds 9.8V (typically),
operation of the driver is enabled and the PWM input signal
takes control of the gate drives. If VCC drops below the
falling threshold of 7.6V (typically), operation of the driver is
disabled.
Q
= 100nC
GATE
0.4
50nC
Pre-POR Overvoltage Protection
0.2
0.0
20nC
Prior to VCC exceeding its POR level, the upper gate is held
low and the lower gate is controlled by the overvoltage
protection circuits during initial startup. The PHASE is
connected to the gate of the low side MOSFET (LGATE),
which provides some protection to the microprocessor if the
upper MOSFET(s) is shorted during initial startup. For
complete protection, the low side MOSFET should have a
gate threshold well below the maximum voltage rating of the
load/microprocessor.
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
V (V)
BOOT_CAP
FIGURE 2. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
Gate Drive Voltage Versatility
The ISL6612 and ISL6613 provide the user flexibility in
choosing the gate drive voltage for efficiency optimization.
The ISL6612 upper gate drive is fixed to VCC [+12V], but the
lower drive rail can range from 12V down to 5V depending
on what voltage is applied to PVCC. The ISL6613 ties the
upper and lower drive rails together. Simply applying a
voltage from 5V up to 12V on PVCC sets both gate drive rail
voltages simultaneously.
When VCC drops below its POR level, both gates pull low
and the Pre-POR overvoltage protection circuits are not
activated until VCC resets.
Internal Bootstrap Device
Both drivers feature an internal bootstrap schottky diode.
Simply adding an external capacitor across the BOOT and
PHASE pins completes the bootstrap circuit. The bootstrap
function is also designed to prevent the bootstrap capacitor
from overcharging due to the large negative swing at the
trailing-edge of the PHASE node. This reduces voltage
stress on the boot to phase pins.
Over-Temperature Protection (OTP)
When the junction temperature of the IC exceeds +150°C
(typically), both upper and lower gates turn off. The driver
stays off and does not return to normal operation until its
junction temperature comes down below +108°C (typically).
For high frequency applications, applying a lower voltage to
PVCC helps reduce the power dissipation and lower the
junction temperature of the IC. This method reduces the risk
of tripping OTP.
The bootstrap capacitor must have a maximum voltage
rating above UVCC + 5V and its capacitance value can be
chosen from Equation 1:
Q
GATE
-------------------------------------
C
BOOT_CAP
V
Power Dissipation
BOOT_CAP
(EQ. 1)
Package power dissipation is mainly a function of the
Q
UVCC
switching frequency (f ), the output drive impedance, the
G1
SW
-----------------------------------
Q
=
N
Q1
GATE
V
external gate resistance, and the selected MOSFET’s internal
gate resistance and total gate charge. Calculating the power
dissipation in the driver for a desired application is critical to
ensure safe operation. Exceeding the maximum allowable
power dissipation level will push the IC beyond the maximum
recommended operating junction temperature of +125°C. The
maximum allowable IC power dissipation for the SO8 package
GS1
where Q is the amount of gate charge per upper MOSFET
G1
at V
gate-source voltage and N is the number of
GS1
control MOSFETs. The V
Q1
term is defined as the
BOOT_CAP
allowable droop in the rail of the upper gate drive.
FN9153 Rev 9.00
June 15, 2010
Page 8 of 12
ISL6612, ISL6613
is approximately 800mW at room temperature, while the power
dissipation capacity in the EPSOIC and DFN packages, with an
exposed heat escape pad, is more than 2W and 1.5W,
respectively. Both EPSOIC and DFN packages are more
suitable for high frequency applications. See “Layout
UVCC
BOOT
D
C
GD
R
HI1
G
C
DS
Considerations” on page 9 for thermal transfer improvement
suggestions. When designing the driver into an application, it is
recommended that the following calculation is used to ensure
safe operation at the desired frequency for the selected
MOSFETs. The total gate drive power losses due to the gate
charge of MOSFETs and the driver’s internal circuitry and their
corresponding average driver current can be estimated using
Equation 2 and Equation 3, respectively,
R
R
LO1
R
GI1
C
G1
GS
Q
1
S
PHASE
FIGURE 3. TYPICAL UPPER-GATE DRIVE TURN-ON PATH
LVCC
(EQ. 2)
P
= P
+ P
+ I VCC
Q
Qg_TOT
Qg_Q1
Qg_Q2
2
D
Q
UVCC
G1
C
R
GD
---------------------------------------
P
=
F
N
N
Qg_Q1
SW
Q1
V
GS1
R
HI2
G
C
DS
2
Q
LVCC
R
G2
LO2
R
GI2
C
G2
--------------------------------------
P
=
F
Qg_Q2
SW
Q2
V
GS2
GS
Q
2
S
Q
UVCC N
Q
LVCC N
G2 Q2
G1
Q1
----------------------------------------------------- ----------------------------------------------------
I
=
+
F
+ I
DR
SW
Q
V
V
GS2
GS1
FIGURE 4. TYPICAL LOWER-GATE DRIVE TURN-ON PATH
(EQ. 3)
where the gate charge (Q and Q ) is defined at a particular
Layout Considerations
G1
G2
and V
gate to source voltage (V
) in the corresponding
GS1
GS2
For heat spreading, place copper underneath the IC whether it
has an exposed pad or not. The copper area can be extended
beyond the bottom area of the IC and/or connected to buried
copper plane(s) with thermal vias. This combination of vias for
vertical heat escape, extended copper plane, and buried
planes for heat spreading allows the IC to achieve its full
thermal potential.
MOSFET data sheet; I is the driver’s total quiescent current
Q
with no load at both drive outputs; N and N are number of
Q1 Q2
upper and lower MOSFETs, respectively; UVCC and LVCC are
the drive voltages for both upper and lower FETs, respectively.
The I VCC product is the quiescent power of the driver
Q*
without capacitive load and is typically 116mW at 300kHz.
The total gate drive power losses are dissipated among the
resistive components along the transition path. The drive
resistance dissipates a portion of the total gate drive power
losses, the rest will be dissipated by the external gate resistors
Place each channel power component as close to each other
as possible to reduce PCB copper losses and PCB parasitics:
shortest distance between DRAINs of upper FETs and
SOURCEs of lower FETs; shortest distance between DRAINs
of lower FETs and the power ground. Thus, smaller amplitudes
of positive and negative ringing are on the switching edges of
the PHASE node. However, some space in between the power
components is required for good airflow. The traces from the
drivers to the FETs should be kept short and wide to reduce the
inductance of the traces and to promote clean drive signals.
(R and R ) and the internal gate resistors (R
and R )
G1 G2 GI1
GI2
of MOSFETs. Figures 3 and 4 show the typical upper and lower
gate drives turn-on transition path. The power dissipation on the
driver can be roughly estimated as:
P
= P
+ P
+ I VCC
DR
DR_UP
DR_LOW
Q
R
R
P
Qg_Q1
HI1
LO1
-------------------------------------- --------------------------------------- ---------------------
P
=
+
DR_UP
R
+ R
R
+ R
EXT1
2
HI1
EXT1
LO1
R
R
P
Qg_Q2
HI2
LO2
-------------------------------------- --------------------------------------- ---------------------
P
R
=
+
DR_LOW
R
+ R
R
+ R
EXT2
2
HI2
EXT2
LO2
R
R
GI1
GI2
-------------
-------------
= R
+
R
= R +
G2
EXT1
G1
EXT2
N
N
Q1
Q2
(EQ. 4)
FN9153 Rev 9.00
June 15, 2010
Page 9 of 12
ISL6612, ISL6613
Package Outline Drawing
L10.3x3
10 LEAD DUAL FLAT PACKAGE (DFN)
Rev 6, 09/09
6
3.00
A
B
PIN #1 INDEX AREA
1
2
6
PIN 1
INDEX AREA
10 x 0.23
4
(4X)
0.10
1.60
10x 0.35
4
TOP VIEW
BOTTOM VIEW
C A B
M
0.10
(4X)
0.415
0.23
PACKAGE
OUTLINE
0.35
SEE DETAIL "X"
0.10
(10 x 0.55)
(10x 0.23)
C
C
BASE PLANE
0.20
SEATING PLANE
0.08 C
SIDE VIEW
(8x 0.50)
5
0.20 REF
0.05
C
1.60
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Lead width applies to the metallized terminal and is measured
between 0.18mm and 0.30mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature.
5.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 indentifier may be
either a mold or mark feature.
FN9153 Rev 9.00
June 15, 2010
Page 10 of 12
ISL6612, ISL6613
Small Outline Exposed Pad Plastic Packages (EPSOIC)
M8.15B
N
8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD
PLASTIC PACKAGE
INDEX
AREA
0.25(0.010)
M
B M
H
E
INCHES
MILLIMETERS
-B-
SYMBOL
MIN
MAX
MIN
1.43
0.03
0.35
0.19
4.80
3.81
MAX
1.68
0.13
0.49
0.25
4.98
3.99
NOTES
A
A1
B
C
D
E
e
0.056
0.001
0.0138
0.0075
0.189
0.150
0.066
0.005
0.0192
0.0098
0.196
0.157
-
1
2
3
-
TOP VIEW
9
-
L
3
SEATING PLANE
A
4
-A-
D
o
0.050 BSC
1.27 BSC
-
h x 45
H
h
0.230
0.010
0.016
0.244
0.016
0.035
5.84
0.25
0.41
6.20
0.41
0.64
-
-C-
5
L
6
e
B
A1
C
N
8
8
7
0.10(0.004)
0°
-
8°
0°
-
8°
-
11
P
0.25(0.010) M
SIDE VIEW
C A M B S
0.094
0.094
2.387
2.387
P1
-
-
11
Rev. 4 1/09
NOTES:
1
2
3
1. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
P1
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.15mm (0.006 inch) per side.
N
4. Dimension “E” does not include interlead flash or protrusions.
Interlead flash and protrusions shall not exceed 0.25mm (0.010
inch) per side.
P
BOTTOM VIEW
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: INCH. Converted millimeter dimensions
are not necessarily exact.
11. Dimensions “P” and “P1” are thermal and/or electrical enhanced
variations. Values shown are maximum size of exposed pad
within lead count and body size.
FN9153 Rev 9.00
June 15, 2010
Page 11 of 12
ISL6612, ISL6613
Small Outline Plastic Packages (SOIC)
M8.15 (JEDEC MS-012-AA ISSUE C)
N
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
0.25(0.010)
M
B M
H
INCHES
MILLIMETERS
E
SYMBOL
MIN
MAX
MIN
1.35
0.10
0.33
0.19
4.80
3.80
MAX
1.75
0.25
0.51
0.25
5.00
4.00
NOTES
-B-
A
A1
B
C
D
E
e
0.0532
0.0040
0.013
0.0688
0.0098
0.020
-
-
1
2
3
L
9
SEATING PLANE
A
0.0075
0.1890
0.1497
0.0098
0.1968
0.1574
-
-A-
3
h x 45°
D
4
-C-
0.050 BSC
1.27 BSC
-
H
h
0.2284
0.0099
0.016
0.2440
0.0196
0.050
5.80
0.25
0.40
6.20
0.50
1.27
-
e
A1
C
5
B
0.10(0.004)
L
6
0.25(0.010) M
C
A M B S
N
8
8
7
NOTES:
0°
8°
0°
8°
-
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Inter-
lead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
© Copyright Intersil Americas LLC 2005-2010. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN9153 Rev 9.00
June 15, 2010
Page 12 of 12
相关型号:
©2020 ICPDF网 联系我们和版权申明