概述
规格参数
数据手册ISL88731AHRZ-T7 概述
Power Supply Support Circuit 电源管理电路
ISL88731AHRZ-T7 规格参数
| 是否Rohs认证： | 符合 | 生命周期： | Transferred |
| 包装说明： | HVQCCN, | Reach Compliance Code： | compliant |
| 风险等级： | 5.68 | 可调阈值： | NO |
| 模拟集成电路 - 其他类型： | POWER SUPPLY SUPPORT CIRCUIT | JESD-30 代码： | S-PQCC-N28 |
| JESD-609代码： | e3 | 长度： | 5 mm |
| 湿度敏感等级： | 3 | 信道数量： | 1 |
| 功能数量： | 1 | 端子数量： | 28 |
| 最高工作温度： | 100 °C | 最低工作温度： | -10 °C |
| 封装主体材料： | PLASTIC/EPOXY | 封装代码： | HVQCCN |
| 封装形状： | SQUARE | 封装形式： | CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE |
| 座面最大高度： | 0.8 mm | 最大供电电压 (Vsup)： | 26 V |
| 最小供电电压 (Vsup)： | 8 V | 标称供电电压 (Vsup)： | 18 V |
| 表面贴装： | YES | 温度等级： | OTHER |
| 端子面层： | Matte Tin (Sn) - annealed | 端子形式： | NO LEAD |
| 端子节距： | 0.5 mm | 端子位置： | QUAD |
| 宽度： | 5 mm | Base Number Matches： | 1 |
ISL88731AHRZ-T7 数据手册
通过下载ISL88731AHRZ-T7数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载SMBus Level 2 Battery Charger
ISL88731A
Features
The ISL88731A is a highly integrated Lithium-ion battery
charger controller, programmable over the SMBus system
management bus (SMBus). The ISL88731A is intended to be
used in a smart battery charger (SBC) within a smart battery
system (SBS) that throttles the charge power such that the
current from the AC-adapter is automatically limited. High
efficiency is achieved with a DC/DC synchronous-rectifier buck
converter, equipped with diode emulation for enhanced light
load efficiency and system bus boosting prevention. The
ISL88731A charges one to four Lithium-ion series cells, and
delivers up to 8A charge current. Integrated MOSFET drivers
and bootstrap diode result in fewer components and smaller
implementation area. Low offset current-sense amplifiers
provide high accuracy with 10mΩ sense resistors. The
ISL88731A provides 0.5% end-of-charge battery voltage
accuracy.
• 0.5% Battery Voltage Accuracy
• 3% Adapter Current Limit Accuracy
• 3% Charge Current Accuracy
• SMBus 2 Wire Serial Interface
• Battery Short Circuit Protection
• Fast Response for Pulse-Charging
• Fast System-Load Transient Response
• Monitor Outputs
- Adapter Current (3% Accuracy)
- AC-Adapter Detection
• 11-Bit Battery Voltage Setting
• 6 Bit Charge Current/Adapter Current Setting
• 8A Maximum Battery Charger Current
• 11A Maximum Adapter Current
• +8V to +28V Adapter Voltage Range
• Pb-Free (RoHS compliant)
The ISL88731A provides a digital output that indicates the
presence of the AC-adapter as well as an analog output which
indicates the adapter current within 4% accuracy.
The ISL88731A is available in a small 5mmx5mm 28 Ld thin
(0.8mm) QFN package. An evaluation kit is available to reduce
design time. The ISL88731A is available in Pb-Free packages.
Applications
• Notebook Computers
Pin Configuration
• Tablet PCs
ISL88731A
(28 LD TQFN)
TOP VIEW
• Portable Equipment with Rechargeable Batteries
Ordering Information
PART
NUMBER
(Notes 1, 2, 3)
TEMP
RANGE
(°C)
28 27 26 25 24 23 22
PART
MARKING
PACKAGE
(Pb-Free)
PKG.
DWG. #
NC
ACIN
VREF
ICOMP
NC
VDDP
LGATE
PGND
CSOP
CSON
NC
1
2
3
4
5
6
7
21
20
19
18
17
16
15
ISL88731AHRZ ISL887 31AHRZ -10 to +100 28 Ld 5x5 TQFN L28.5x5B
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
2. These Intersil Pb-free plastic packaged products employ special
Pb-free material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is
RoHS compliant and compatible with both SnPb and Pb-free soldering
operations). Intersil Pb-free products are MSL classified at Pb-free
peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
VCOMP
NC
VFB
8
9
10
11 12 13 14
3. For Moisture Sensitivity Level (MSL), please see device information
page for ISL88731A. For more information on MSL please see
techbrief TB363.
June 8, 2011
FN6738.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2008, 2009, 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1
ISL88731A
VCC
REF
DCIN
LINEAR
REGULATOR
REFERENCE
VDDP
VREF
11
DACV
DACS
DACI
VDDSMB
DACV
6
6
DACS
DACI
SMBUS
SDA
SCL
ACOK
+
-
EN
ACIN
ICM
BUFF
CSSP
CSSN
LEVEL
SHIFTER
20x
-
EN
GMS
DACS
DACI
+
BOOT
ICOMP
CSO
UGATE
PHASE
CSOP
CSON
LEVEL
SHIFTER
20x
-
GMI
DC/DC
CONVERTER
+
LVB
VDDP
LVB
DACV
+
GMV
LGATE
-
PGND
GND
VFB
500k 100k
EN
CSSP
VCOMP
FIGURE 1. FUNCTIONAL BLOCK DIAGRAM
AC ADAPTER
TO SYSTEM
RS1
CSSP
ACIN
CSSN
UGATE
PHASE
RS2
TO BATTERY
DCIN
ISL88731A
BOOT
LGATE
CSOP
CSON
VFB
AGND
ICOMP
VCOMP
VDDP
PGND
PGND
VREF
ACOK
ICM
SDA
SCL
VDDSMB
VCC
GND
AGND
FIGURE 2. TYPICAL APPLICATION CIRCUIT
FN6738.3
June 8, 2011
2
ISL88731A
Absolute Maximum Ratings
Thermal Information
DCIN, CSSP, CSSN, CSOP, CSON, VFB . . . . . . . . . . . . . . . . . . . -0.3V to +28V
CSSP-CSSN, CSOP-CSON, PGND-GND . . . . . . . . . . . . . . . . . . -0.3V to +0.3V
PHASE to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -6V to +30V
BOOT to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +33V
BOOT to PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
UGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PHASE - 0.3V to BOOT +0.3V
LGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PGND - 0.3V to VDDP +0.3V
ICOMP, VCOMP, VREF, to GND. . . . . . . . . . . . . . . . . . . . . -0.3V to VCC +0.3V
VDDSMB, SCL, SDA, ACIN, ACOK . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
VDDP, ICM, VCC to GND, VDDP to PGND . . . . . . . . . . . . . . . . . . -0.3V to +6V
Thermal Resistance (Typical, Notes 4, 5)
QFN Package . . . . . . . . . . . . . . . . . . . . . . . .
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -55°C to +150°C
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . -10°C to +100°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
θ
(°C/W)
36
θ
(°C/W)
6
JA
JC
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θ is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
JA
Brief TB379
5. For θ , the “case temp” location is the center of the exposed metal pad on the package underside.
JC
Electrical Specifications DCIN = CSSP = CSSN = 18V, CSOP = CSON = 12V, VDDP = 5V, BOOT-PHASE = 5.0V, GND = PGND = 0V,
CVDDP = 1µF, IVDDP = 0mA, T = -10°C to +100°C. Boldface limits apply over the operating temperature range, -10°C to +100°C.
A
MIN
MAX
PARAMETER
CONDITIONS
(Note 6)
TYP
(Note 6) UNITS
CHARGE VOLTAGE REGULATION
Battery Full Charge Voltage and Accuracy
ChargeVoltage = 0x41A0
16.716
-0.5
16.8
16.884
0.5
V
%
V
ChargeVoltage = 0x3130
ChargeVoltage = 0x20D0
ChargeVoltage = 0x1060
12.529 12.592 12.655
-0.5
8.350
-0.6
0.5
8.450
0.6
%
V
8.4
%
V
4.163
-0.7
4.192
4.221
0.7
%
V
Battery Undervoltage Lockout Trip Point for Trickle VFB rising
Charge
2.55
2.7
2.85
Battery Undervoltage Lockout Trip Point Hysteresis
CHARGE CURRENT REGULATION
100
250
400
mV
CSOP to CSON Full-Scale Current-Sense Voltage
78.22
7.822
-3
80.64
8.064
83.06
8.306
3
mV
A
Charge Current and Accuracy
RS2 = 10mΩ (see Figure 2)
ChargingCurrent = 0x1f80
%
RS2 = 10mΩ (see Figure 2)
ChargingCurrent = 0x0f80
3.809
-4
3.968
128
4.126
4
A
%
RS2 = 10mΩ (see Figure 2)
64
220
mA
ChargingCurrent = 0x0080
Charge Current Gain Error
Based on charge current = 128mA and 8.064A
-1.6
0
1.4
19
%
V
CSOP/CSON Input Voltage Range
FN6738.3
June 8, 2011
3
ISL88731A
Electrical Specifications DCIN = CSSP = CSSN = 18V, CSOP = CSON = 12V, VDDP = 5V, BOOT-PHASE = 5.0V, GND = PGND = 0V,
CVDDP = 1µF, IVDDP = 0mA, T = -10°C to +100°C. Boldface limits apply over the operating temperature range, -10°C to +100°C. (Continued)
A
MIN
MAX
PARAMETER
Battery Quiescent Current
CONDITIONS
Adapter present, not charging,
(Note 6)
TYP
135
(Note 6) UNITS
400
µA
I
+ I + I + I
+ I
+ I
CSOP CSON PHASE CSSP CSSN
FB
V
= V = V = V = 19V, V
= 5V
PHASE
CSON CSOP
DCIN
ACIN
Adapter Absent
+ I + I
-1
0.2
3
4
µA
I
+ I
+ I
DCIN
+ I
FB
CSOP CSON
= V
PHASE CSSP CSSN
V
= V = 19V, V = 0V
PHASE
+I
ADAPTER
CSON
CSOP
Adapter Quiescent Current
I
V
+I
10
mA
DCIN CSSP CSSN
= 8V to 26V, V
4V to 16.8V
BATTERY
INPUT CURRENT REGULATION
CSSP to CSSN Full-Scale Current-Sense Voltage
Input Current Accuracy
CSSP = 19V
RS1 = 10mΩ (see Figure 2)
106.7
-3
110
113.3
3
mV
%
Adapter Current = 11004mA or 3584mA
RS1 = 10mΩ (see Figure 2)
-5
5
%
Adapter Current = 2048mA
Input Current Limit Gain Error
Input Current Limit Offset
CSSP/CSSN Input Voltage Range
ICM Gain
Based on InputCurrent = 1024mA and 11004mA
-1.5
-1
1.5
1
%
mV
V
8
26
V
V
V
V
V
= 110mV
= 110mV
= 55mV or 35mV
= 20mV
20
V/V
%
CSSP-CSSN
CSSP-CSSN
CSSP-CSSN
CSSP-CSSN
CSSP-CSSN
ICM Accuracy
-2.5
-4
2.5
4
%
-8
8
%
ICM Max Output Current
SUPPLY AND LINEAR REGULATOR
DCIN, Input Voltage Range
VDDP Output Voltage
VDDP Load Regulation
VDDSMB Range
= 0.1V
500
µA
8
26
5.3
100
5.5
2.6
150
27
V
V
8.0V < V
< 28V, no load
< 30mA
4.9
5.1
35
DCIN
0 < I
VDDP
mV
V
2.7
2.4
40
VDDSMB UVLO Rising
VDDSMB UVLO Hysteresis
VDDSMB Quiescent Current
V REFERENCE
2.5
100
20
V
mV
µA
VDDP = SCL = SDA = 5.5V
VREF Output Voltage
ACOK
0 < I
< 300µA
3.1
2
3.2
8
3.3
1
V
VREF
ACOK Sink Current
V
= 0.4V, ACIN = 1.5V
= 5.5V, ACIN = 3.7V
mA
µA
ACOK
ACOK Leakage Current
ACIN
V
ACOK
ACIN Rising Threshold
ACIN Threshold Hysteresis
ACIN Input Bias Current
SWITCHING REGULATOR
Frequency
3.1
40
-1
3.2
60
3.3
90
1
V
mV
µA
330
400
440
kHz
FN6738.3
June 8, 2011
4
ISL88731A
Electrical Specifications DCIN = CSSP = CSSN = 18V, CSOP = CSON = 12V, VDDP = 5V, BOOT-PHASE = 5.0V, GND = PGND = 0V,
CVDDP = 1µF, IVDDP = 0mA, T = -10°C to +100°C. Boldface limits apply over the operating temperature range, -10°C to +100°C. (Continued)
A
MIN
MAX
PARAMETER
BOOT Supply Current
CONDITIONS
(Note 6)
TYP
290
0
(Note 6) UNITS
UGATE High
170
400
2
µA
µA
Ω
PHASE Input Bias Current
UGATE ON-Resistance Low
UGATE ON-Resistance High
LGATE ON-Resistance High
LGATE ON-Resistance Low
Dead Time
V
= 28V, V
CSON
= V
= 20V
PHASE
DCON
UGATE
UGATE
LGATE
LGATE
I
I
I
I
= -100mA
= 10mA
0.9
1.4
1.4
0.9
50
1.6
2.5
2.5
1.6
80
Ω
= +10mA
= -100mA
Ω
Ω
Falling UGATE to rising LGATE or
falling LGATE to rising UGATE
35
ns
ERROR AMPLIFIERS
GMV Amplifier Transconductance
GMI Amplifier Transconductance
GMS Amplifier Transconductance
GMI/GMS Saturation Current
GMV Saturation Current
ICOMP, VCOMP Clamp Voltage
LOGIC LEVELS
200
40
250
50
300
60
µA/V
µA/V
µA/V
µA
40
50
60
15
21
25
10
17
30
µA
0.25V < V
< 3.5V
200
300
400
mV
ICOMP, VCOMP
SDA/SCL Input Low Voltage
SDA/SCL Input High Voltage
SDA/SCL Input Bias Current
SDA, Output Sink Current
NOTE:
VDDSMB = 2.7V to 5.5V
VDDSMB = 2.7V to 5.5V
VDDSMB = 2.7V to 5.5V
0.8
1
V
V
2
-1
7
µA
mA
V
= 0.4V
15
SDA
6. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
SMBus Timing Specification VDDSMB = 2.7V TO 5.5V
PARAMETERS
SYMBOL
CONDITIONS
MIN
10
TYP
MAX
100
UNITS
kHz
µs
SMBus Frequency
Bus Free Time
FSMB
TBUF
4.7
4
Start Condition Hold Time from SCL
Start Condition Setup Time from SCL
Stop Condition Setup Time from SCL
SDA Hold Time from SCL
SDA Setup Time from SCL
SCL Low Timeout (Note 7)
SCL Low Period
THD:STA
TSU:STA
TSU:STO
THD:DAT
TSU:DAT
TTIMEOUT
TLOW
µs
4.7
4
µs
µs
300
250
22
4.7
4
ns
ns
25
30
ms
µs
SCL High Period
THIGH
µs
Maximum Charging Period Without a SMBus Write to
ChargeVoltage or ChargeCurrent Register
140
180
220
s
NOTES:
7. If SCL is low for longer than the specified time, the charger is disabled.
FN6738.3
June 8, 2011
5
ISL88731A
Typical Operating Performance
DCIN = 20V, 3S2P Li-Battery, T = +25°C, unless otherwise noted.
A
5.15
1.0%
0.5%
0.0%
3.23
3.22
5.10
5.05
5.00
4.95
3.21
3.20
3.19
3.18
3.17
-0.5%
-1.0%
4.90
4.85
0
20
40
60
80
100
0
50
100
150
200
VDDP LOAD CURRENT (mA)
I VREF (µA)
FIGURE 3. VDD LOAD REGULATION
FIGURE 4. VREF LOAD REGULATION
3.5
15
10
5
13.0
12.5
12.0
11.5
11.0
10.5
10.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
VCHG (V)
0
-5
-10
-15
ICHG (A)
1
2
3
4
5
6
7
8
0
20
40
60
80
100
120
140
160
ADAPTER CURRENT (A)
TIME (MINUTES)
FIGURE 5. ICM ACCURACY vs AC-ADAPTER CURRENT
FIGURE 6. TYPICAL CHARGING VOLTAGE AND CURRENT
VCOMP
ICOMP
VCOMP
ICOMP
CHARGE
CURRENT
CHARGE
CURRENT
INDUCTOR
CURRENT
INDUCTOR
CURRENT
FIGURE 8. CHARGE DISABLE
FIGURE 7. CHARGE ENABLE
FN6738.3
June 8, 2011
6
ISL88731A
Typical Operating Performance
DCIN = 20V, 3S2P Li-Battery, T = +25°C, unless otherwise noted.
A
UGATE
UGATE
LGATE
INDUCTOR
CURRENT
LGATE
PHASE
INDUCTOR
CURRENT
PHASE
FIGURE 10. SWITCHING WAVEFORMS IN CC MODE
FIGURE 9. SWITCHING WAVEFORMS AT DIODE EMULATION
CSON/
V
BATTERY
CSON/
V
BATTERY
BATTERY
CURRENT
BATTERY
CURRENT
FIGURE 11. BATTERY REMOVAL
FIGURE 12. BATTERY INSERTION
100
95
SYSTEM
LOAD
90
BATTERY
VOLTAGE
16.8V
BATTERY
85
80
CHARGE
CURRENT
12.6V
BATTERY
8.4V
ADAPTER
CURRENT
BATTERY
75
70
4.2V
BATTERY
0
2
4
6
8
CHARGE CURRENT (A)
FIGURE 14. EFFICIENCY vs CHARGE CURRENT AND BATTERY
VOLTAGE (EFFICIENCY DCIN = 20V)
FIGURE 13. LOAD TRANSIENT RESPONSE
FN6738.3
June 8, 2011
7
ISL88731A
PGND
Functional Pin Descriptions
BOOT
Power Ground. Connect PGND to the source of the low side
MOSFET.
High-Side Power MOSFET Driver Power-Supply Connection.
Connect a 0.1µF capacitor from BOOT to PHASE.
VCC
Power input for internal analog circuits. Connect a 4.7Ω resistor
from VCC to VDDP and a 1µF ceramic capacitor from VCC to
ground.
UGATE
High-Side Power MOSFET Driver Output. Connect to the high-side
N-Channel MOSFET gate.
VDDP
LGATE
Linear Regulator Output. VDDP is the output of the 5.2V linear
regulator supplied from DCIN. VDDP also directly supplies the
LGATE driver and the BOOT strap diode. Bypass with a 1µF
ceramic capacitor from VDDP to PGND.
Low-Side Power MOSFET Driver Output. Connect to low-side
N-Channel MOSFET. LGATE drives between VDDP and PGND.
PHASE
ICOMP
High-Side Power MOSFET Driver Source Connection. Connect to
the source of the high-side N-Channel MOSFET.
Compensation Point for the charging current and adapter current
regulation Loop. Connect 0.01µF to GND. See “Voltage Control
Loop” on page 20 for details of selecting the ICOMP capacitor.
CSOP
Charge Current-Sense Positive Input.
VCOMP
CSON
Compensation Point for the voltage regulation loop. Connect
4.7kΩ in series with 0.01µF to GND. See “Voltage Control Loop”
on page 20 for details on selecting VCOMP components.
Charge Current-Sense Negative Input.
CSSP
VFB
Input Current-Sense Positive Input.
Feedback for the Battery Voltage.
CSSN
VDDSMB
Input Current-Sense Negative Input.
SMBus interface Supply Voltage Input. Bypass with a 0.1µF
capacitor to GND.
DCIN
Charger Bias Supply Input. Bypass DCIN with a 0.1µF capacitor to
GND.
SDA
SMBus Data I/O. Open-drain Output. Connect an external pull-up
resistor according to SMBus specifications.
ACIN
AC-adapter Detection Input. Connect to a resistor divider from the
AC-adapter output.
SCL
SMBus Clock Input. Connect an external pull-up resistor
according to SMBus specifications.
ACOK
AC Detect Output. This open drain output is high impedance
when ACIN is greater than 3.2V. The ACOK output remains low
when the ISL88731A is powered down. Connect a 10k pull-up
resistor from ACOK to VDDSMB.
GND
Analog Ground. Connect directly to the backside paddle. Connect
to PGND close to the output capacitor.
Back Side Paddle
Connect the backside paddle to GND.
ICM
Input Current Monitor Output. ICM voltage equals 20 x (V
-
CSSP
V
).
CSSN
NC
VREF
No Connect. Pins 1, 5, 7 and 14 are not connected.
VREF is a reference output pin. It is internally compensated. Do
not connect a decoupling capacitor.
FN6738.3
June 8, 2011
8
ISL88731A
driver to MOSFET gate, and from the source of MOSFET to PGND.
An internal Schottky diode between the VDDP pin and BOOT pin
keeps the bootstrap capacitor charged.
Theory of Operation
Introduction
The ISL88731A includes all of the functions necessary to charge
1-to-4 cell Li-ion and Li-polymer batteries. A high efficiency
synchronous buck converter is used to control the charging
voltage up to 19.2V and charging current up to 8A. The
ISL88731A also has input current limiting up to 11A. The Input
current limit, charge current limit and charge voltage limit are set
by internal registers written with SMBus. Figure 2 shows the
ISL88731A “Typical Application Circuit”.
AC-Adapter Detection
Connect the AC-adapter voltage through a resistor divider to ACIN
to detect when AC power is available, as shown in Figure 2. ACOK
is an open-drain output and is active low when ACIN is less than
V
, and high when ACIN is above V . The ACIN rising
th,fall
th,rise
threshold is 3.2V (typ) with 57mV hysteresis.
Current Measurement
The ISL88731A charges the battery with constant charge current,
set by the ChargeCurrent register, until the battery voltage rises to
a voltage set by the ChargeVoltage register. The charger will then
operate at a constant voltage. The adapter current is monitored
and if the adapter current rises to the limit set by the InputCurrent
register, battery charge current is reduced so the charger does not
reduce the adapter current available to the system.
Use ICM to monitor the adapter current being sensed across
CSSP and CSSN. The output voltage range is 0V to 2.5V. The
voltage of ICM is proportional to the voltage drop across CSSP
and CSSN, and is given by Equation 1:
(EQ. 1)
ICM = 20 ⋅ I
⋅ R
S1
INPUT
The ISL88731A features a voltage regulation loop (VCOMP) and
two current regulation loops (ICOMP). The VCOMP voltage
regulation loop monitors VFB to limit the battery charge voltage.
The ICOMP current regulation loop limits the battery charging
current delivered to the battery to ensure that it never exceeds
the current set by the ChargeCurrent register. The ICOMP current
regulation loop also limits the input current drawn from the
AC-adapter to ensure that it never exceeds the limit set by the
InputCurrent register, and to prevent a system crash and
AC-adapter overload.
where I
is the DC current drawn from the AC-adapter. It
ADAPTER
is recommended to have an RC filter at the ICM output for
minimizing the switching noise.
VDDP Regulator
VDDP provides a 5.2V supply voltage from the internal LDO
regulator from DCIN and can deliver up to 30mA of continuous
current. The MOSFET drivers are powered by VDDP. VDDP also
supplies power to VCC through a low-pass filter as shown in the
“Typical Application Circuit” (see Figure 2) on page 2. Bypass
VDDP and VCC with a 1µF capacitor.
PWM Control
The ISL88731A employs a fixed frequency PWM control
architecture with a feed-forward function. The feed-forward
function maintains a constant modulator gain of 11 to achieve fast
line regulation as the input voltage changes.
VDDSMB Supply
The VDDSMB input provides power to the SMBus interface.
Connect VDDSMB to VCC, or apply an external supply to VDDSMB.
Bypass VDDSMB to GND with a 0.1µF or greater ceramic
capacitor.
The duty cycle of the buck regulator is controlled by the lower of
the voltages on ICOMP and VCOMP. The voltage on ICOMP and
VCOMP are inputs to a Lower Voltage Buffer (LVB) who’s output is
the lower of the two inputs. The output of the LVB is compared to
an internal 400kHz ramp to produce the Pulse Width Modulated
signal that controls the UGATE and LGATE drivers. An internal
clamp holds the higher of the two voltages (0.3V) above the lower
voltage. This speeds the transition from voltage loop control to
current loop control or vice versa.
The typical application connects VDDSMB to the same power
source as the SMBus master. This supply should be active and
greater than 2.5V when either the adapter or the battery is
present.
ISL88731A does not function when VDDSMB is below its
specified Under Voltage Lockout (UVLO) voltage. All of the SMBus
registers in ISL88731A are powered by VDDSMB and are set to
zero when it is below the UVLO threshold. Other functions are
unpredictable when VDDSMB is below the UVLO threshold.
The ISL88731A can operate up to 99.6% duty cycle if the input
voltage drops close to or below the battery charge voltage (drop
out mode). The DC/DC converter has a timer to prevent the
frequency from dropping into the audible frequency range.
Short Circuit Protection and 0V Battery
Charging
Since the battery charger will regulate the charge current to the
limit set by the ChargeCurrent register, it automatically has short
circuit protection and is able to provide the charge current to
wake up an extremely discharged battery. Undervoltage trickle
charge folds back current if there is a short circuit on the output.
To prevent boosting of the system bus voltage, the battery
charger drives the lower FET in a way that prevents negative
inductor current.
An adaptive gate drive scheme is used to control the dead time
between two switches. The dead time control circuit monitors the
LGATE output and prevents the upper side MOSFET from turning
on until 20ns after LGATE falls below 1V V , preventing
GS
cross-conduction and shoot-through. The same occurs for LGATE
turn on. In order for the dead time circuit to work properly, there
must be a low resistance, low inductance path from the LGATE
FN6738.3
June 8, 2011
9
ISL88731A
Undervoltage Detect and Battery Trickle
Charging
If the voltage at CSON falls below 2.5V, the ISL88731A reduces
the charge current limit to 128mA to trickle charge the battery.
When the voltage rises above 2.7V the charge current reverts to
the programmed value in the ChargeCurrent register.
Overvoltage Protection
ISL88731A has an Overvoltage Protection circuit that limits the
output voltage when the battery is removed or disconnected by a
pulse charging circuit. If CSON exceeds the output voltage set
point in the charge voltage register by more than 300mV an
internal comparator pulls VCOMP down and turns off both upper
and lower FETs of the buck as in Figure 15. There is a delay of
approximately 1µs between V
and pulling VCOMP, LGATE and UGATE low. After UGATE and
LGATE are turned OFF inductor current continues to flow through
the body diode of the lower FET and V
inductor current reaches zero.
exceeding the OVP trip point
Over-Temperature Protection
If the die temperature exceeds +150°C, it stops charging. Once
the die temperature drops below +125°C, charging will start up
again.
OUT
continues to rise until
OUT
FIGURE 15. OVERVOLTAGE PROTECTION IN ISL88731A
FN6738.3
June 8, 2011
10
ISL88731A
The System Management Bus
The System Management Bus (SMBus) is a 2-wire bus that
supports bidirectional communications. The protocol is described
briefly here. More detail is available from www.smbus.org.
SDA
SCL
General SMBus Architecture
S
P
VDDSMB
START
CONDITION
STOP
CONDITION
SMBUS SLAVE
INPUT
STATE
MACHINE,
REGISTERS,
MEMORY,
ETC
SCL
FIGURE 17. START AND STOP WAVEFORMS
OUTPUT
INPUT
CONTROL
SMBUS MASTER
Acknowledge
INPUT
SDA
SCL
OUTPUT
INPUT
OUTPUTCONTROL
CONTROL
Each address and data transmission uses 9-clock pulses. The ninth
pulse is the acknowledge bit (ACK). After the start condition, the
master sends 7-slave address bits and a R/W bit during the next 8-
clock pulses. During the ninth clock pulse, the device that recognizes
its own address holds the data line low to acknowledge. The
acknowledge bit is also used by both the master and the slave to
acknowledge receipt of register addresses and data (see Figure 18).
CPU
SDA
OUTPUT
CONTROL
SMBUS SLAVE
INPUT
OUTPUT
INPUT
STATE
MACHINE,
REGISTERS,
MEMORY,
ETC
SCL
CONTROL
SDA
OUTPUT
CONTROL
SCL
2
8
1
9
TO OTHER
SDA
SLAVE DEVICES
MSB
Data Validity
START
ACKNOWLEDGE
FROM SLAVE
The data on the SDA line must be stable during the HIGH period
of the SCL, unless generating a START or STOP condition. The
HIGH or LOW state of the data line can only change when the
clock signal on the SCL line is LOW. Refer to Figure 16.
2
FIGURE 18. ACKNOWLEDGE ON THE I C BUS
SMBus Transactions
All transactions start with a control byte sent from the SMBus
master device. The control byte begins with a Start condition,
followed by 7-bits of slave address (0001001 for the ISL88731A)
followed by the R/W bit. The R/W bit is 0 for a write or 1 for a read. If
any slave devices on the SMBus bus recognize their address, they
will Acknowledge by pulling the serial data (SDA) line low for the last
clock cycle in the control byte. If no slaves exist at that address or
are not ready to communicate, the data line will be 1, indicating a
Not Acknowledge condition.
SDA
SCL
DATA LINE CHANGE
STABLE
OF DATA
DATA VALID ALLOWED
FIGURE 16. DATA VALIDITY
Once the control byte is sent, and the ISL88731A acknowledges
it, the 2nd byte sent by the master must be a register address
byte such as 0x14 for the ChargeCurrent register. The register
address byte tells the ISL88731A which register the master will
write or read. See Table 1 for details of the registers. Once the
ISL88731A receives a register address byte it responds with an
acknowledge.
START and STOP Conditions
As shown in Figure 17, START condition is a HIGH-to-LOW transition
of the SDA line while SCL is HIGH.
The STOP condition is a LOW-to-HIGH transition on the SDA line
while SCL is HIGH. A STOP condition must be sent before each
START condition.
FN6738.3
June 8, 2011
11
ISL88731A
Write To A Register
SLAVE
ADDR + W
REGISTER
ADDR
LO BYTE
DATA
HI BYTE
DATA
S
S
A
A
A
A
A
P
Read From A Register
SLAVE
ADDR + W
REGISTER
ADDR
SLAVE
LO BYTE
DATA
HI BYTE
DATA
A
P
S
A
A
N
P
ADDR + R
S
P
START
STOP
A
N
ACKNOWLEDGE
DRIVEN BY THE MASTER
DRIVEN BY ISL88731
NO ACKNOWLEDGE
FIGURE 19. SMBus/ISL88731A READ AND WRITE PROTOCOL
The data (SDA) and clock (SCL) pins have Schmitt-trigger inputs
that can accommodate slow edges. Choose pull-up resistors for
SDA and SCL to achieve rise times according to the SMBus
specifications. The ISL88731A is controlled by the data written to
the registers described in Table 1.
Byte Format
Every byte put on the SDA line must be eight bits long and must
be followed by an acknowledge bit. Data is transferred with the
most significant bit first (MSB) and the least significant bit last
(LSB).
Battery Charger Registers
ISL88731A and SMBus
The ISL88731A supports five battery-charger registers that use
either Write-Word or Read-Word protocols, as summarized in
Table 1. ManufacturerID and DeviceID are “read only” registers
and can be used to identify the ISL88731A. On the ISL88731A,
ManufacturerID always returns 0x0049 (ASCII code for “I” for
Intersil) and DeviceID always returns 0x0001.
The ISL88731A receives control inputs from the SMBus
interface. The serial interface complies with the SMBus protocols
as documented in the System Management Bus Specification
V1.1, which can be downloaded from www.smbus.org. The
ISL88731A uses the SMBus Read-Word and Write-Word
protocols (Figure 19) to communicate with the smart battery. The
ISL88731A is an SMBus slave device and does not initiate
communication on the bus. It responds to the 7-bit address
0b0001001_ (0x12).
Enabling and Disabling Charging
After applying power to ISL88731A, the internal registers contain
their POR values (see Table 1). The POR values for charge current
and charge voltage are 0x0000. These values disable charging.
To enable charging, the ChargeCurrent register must be written
with a number >0x007F and the ChargeVoltage register must be
written with a number >0x000F. Charging can be disabled by
writing 0x0000 to either of these registers.
Read address = 0b00010011 and
Write address = 0b00010010.
In addition, the ISL88731A has two identification (ID) registers: a
16-bit device ID register and a 16-bit manufacturer ID register.
TABLE 1. BATTERY CHARGER REGISTER SUMMARY
REGISTER
ADDRESS
REGISTER NAME
ChargeCurrent
READ/WRITE
Read or Write
DESCRIPTION
6-bit Charge Current Setting
POR STATE
0x0000
0x0000
0x0080
0x0049
0x0001
0x14
0x15
0x3F
0xFE
0xFF
ChargeVoltage
InputCurrent
ManufacturerID
DeviceID
Read or Write
Read or Write
Read Only
11-bit Charge Voltage Setting
6-bit Charge Current Setting
Manufacturer ID
Read Only
Device ID
FN6738.3
June 8, 2011
12
ISL88731A
the ChargeVoltage and ChargeCurrent registers. Use the
Setting Charge Voltage
Write-Word protocol (Figure 19) to write to the ChargeVoltage
register. The register address for ChargeVoltage is 0x15. The
16-bit binary number formed by D15–D0 represents the charge
voltage set point in mV. However, the resolution of the
ISL88731A is 16mV because the D0–D3 bits are ignored as
shown in Table 2. The D-5 bit is also ignored because it is not
needed to span the 1.024V to 19.2V range. Table 2 shows the
mapping between the charge-voltage set point and the 16-bit
number written to the ChargeVoltage register. The ChargeVoltage
register can be read back to verify its contents.
Charge voltage is set by writing a valid 16-bit number to the
ChargeVoltage register. This 16-bit number translates to a
65.535V full-scale voltage. The ISL88731A ignores the first 4
LSBs and uses the next 11 bits to set the voltage DAC. The
charge voltage range of the ISL88731A is 1.024V to 19.200V.
Numbers requesting charge voltage greater than 19.200V result
in a ChargeVoltage of 19.200V. All numbers requesting charge
voltage below 1.024V result in a voltage set point of zero, which
terminates charging. Upon initial power-up or reset, the
ChargeVoltage and ChargeCurrent registers are reset to 0 and
the charger remains shut down until valid numbers are sent to
TABLE 2. CHARGEVOLTAGE (REGISTER 0x15)
DESCRIPTION
BIT
0
BIT NAME
Not used
Not used
Not used
Not used
1
2
3
4
Charge Voltage, DACV 0
Charge Voltage, DACV 1
Charge Voltage, DACV 2
Charge Voltage, DACV 3
Charge Voltage, DACV 4
Charge Voltage, DACV 5
Charge Voltage, DACV 6
Charge Voltage, DACV 7
Charge Voltage, DACV 8
Charge Voltage, DACV 9
Charge Voltage, DACV 10
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 16mV of charger voltage
5
6
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 32mV of charger voltage
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 64mV of charger voltage
7
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 128mV of charger voltage
8
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 256mV of charger voltage
9
0 = Adds 0mV of charger voltage, 1024mV min
1 = Adds 512mV of charger voltage
10
11
12
13
14
15
0 = Adds 0mA of charger voltage
1 = Adds 1024mV of charger voltage
0 = Adds 0mV of charger voltage
1 = Adds 2048mV of charger voltage
0 = Adds 0mV of charger voltage
1 = Adds 4096mV of charger voltage
0 = Adds 0mV of charger voltage
1 = Adds 8192mV of charger voltage
0 = Adds 0mV of charger voltage
1 = Adds 16384mV of charger voltage, 19200mV max
Not used. Normally a 32768mV weight
FN6738.3
June 8, 2011
13
ISL88731A
disabled. To start the charger, write valid numbers to the
Setting Charge Current
ChargeVoltage and ChargeCurrent registers. The ChargeCurrent
register uses the Write-Word protocol (see Figure 19). The
register code for ChargeCurrent is 0x14 (0b00010100). Table 3
shows the mapping between the charge current set point and the
ChargeCurrent number. The ChargeCurrent register can be read
back to verify its contents.
ISL88731A has a 16-bit ChargeCurrent register that sets the
battery charging current. ISL88731A controls the charge current
by controlling the CSOP-CSON voltage. The register’s LSB
translates to 10µV at CSON-CSOP. With a 10mΩ charge current
R
resistor (RS2 in Figure 2), the LSB translates to 1mA
sense
charge current. The ISL88731A ignores the first 7 LSBs and uses
the next 6 bits to control the current DAC. The charge-current
range of the ISL88731A is 0 to 8.064A (using a 10mΩ current-
sense resistor). All numbers requesting charge current above
8.064A result in a current setting of 8.064A. All numbers
requesting charge current between 0mA to 128mA result in a
current setting of 0mA. The default charge current setting at
Power-On Reset (POR) is 0mA. To stop charging, set
The ISL88731A includes a fault limiter for low battery conditions.
If the battery voltage is less than 2.5V, the charge current is
temporarily set to 128mA. The ChargeCurrent register is
preserved and becomes active again when the battery voltage is
higher than 2.7V. This function effectively provides a foldback
current limit, which protects the charger during short circuit and
overload.
ChargeCurrent to 0. Upon initial power-up, the ChargeVoltage and
ChargeCurrent registers are reset to 0 and the charger is
TABLE 3. CHARGE CURRENT (REGISTER 0x14) (10mΩ SENSE RESISTOR, RS2)
BIT
0
BIT NAME
DESCRIPTION
Not used
Not used
Not used
Not used
Not used
Not used
Not used
1
2
3
4
5
6
7
Charge Current, DACI 0
Charge Current, DACI 1
Charge Current, DACI 2
Charge Current, DACI 3
Charge Current, DACI 4
Charge Current, DACI 5
0 = Adds 0mA of charger current
1 = Adds 128mA of charger current
8
0 = Adds 0mA of charger current
1 = Adds 256mA of charger current
9
0 = Adds 0mA of charger current
1 = Adds 512mA of charger current
10
11
12
0 = Adds 0mA of charger current
1 = Adds 1024mA of charger current
0 = Adds 0mA of charger current
1 = Adds 2048mA of charger current
0 = Adds 0mA of charger current
1 = Adds 4096mA of charger current, 8064mA max
13
14
15
Not used
Not used
Not used
FN6738.3
June 8, 2011
14
ISL88731A
inputs in 20µV per LSB increments. To set the input current limit
Setting Input-Current Limit
use the SMBus to write a 16-bit InputCurrent register using the
data format listed in Table 4. The InputCurrent register uses the
Write-Word protocol (see Figure 19). The register code for
InputCurrent is 0x3F (0b00111111). The InputCurrent register
can be read back to verify its contents.
The total power from an AC-adapter is the sum of the power
supplied to the system and the power into the charger and battery.
When the input current exceeds the set input current limit, the
ISL88731A decreases the charge current to provide priority to
system load current. As the system load rises, the available charge
current drops linearly to zero. Thereafter, the total input current
can increase to the limit of the AC-adapter.
The ISL88731A ignores the first 7 LSBs and uses the next
6 bits to control the input-current DAC. The input-current range of
the ISL88731A is from 256mA to 11.004A. All 16-bit numbers
requesting input current above 11.004A result in an input-
current setting of 11.004A. All 16-bit numbers requesting input
current between 0mA to 256mA result in an input-current setting
of 0mA. The default input-current-limit setting at POR is 256mA.
When choosing the current-sense resistor RS1, carefully
calculate its power rating. Take into account variations in the
system’s load current and the overall accuracy of the sense
amplifier. Note that the voltage drop across RS1 contributes
additional power loss, which reduces efficiency. System currents
normally fluctuate as portions of the system are powered up or
put to sleep. Without input current regulation, the input source
must be able to deliver the maximum system current and the
maximum charger-input current. By using the input-current-limit
circuit, the output-current capability of the AC wall adapter can
be lowered, reducing system cost.
The internal amplifier compares the differential voltage between
CSSP and CSSN to a scaled voltage set by the InputCurrent
register. The total input current is the sum of the device supply
current, the charger input current, and the system load current.
The total input current can be estimated by using Equation 2.
I
= I
+ [(I
× V
) ⁄ (V × η)]
BATTERY IN
INPUT
SYSTEM
CHARGE
(EQ. 2)
Where η is the efficiency of the DC/DC converter (typically 85%
to 95%).
The ISL88731A has a 16-bit InputCurrent register that translates
to a 2mA LSB and a 131.071A full-scale current using a 10mΩ
current-sense resistor (RS1 in Figure 2). Equivalently, the 16-bit
InputCurrent number sets the voltage across CSSP and CSSN
TABLE 4. INPUT CURRENT (REGISTER 0x3F) (10mΩ SENSE RESISTOR, RS1)
BIT
0
BIT NAME
DESCRIPTION
Not used
Not used
Not used
Not used
Not used
Not used
Not used
1
2
3
4
5
6
7
Input Current, DACS 0
Input Current, DACS 1
Input Current, DACS 2
Input Current, DACS 3
Input Current, DACS 4
Input Current, DACS 5
0 = Adds 0mA of input current
1 = Adds 256mA of input current
8
0 = Adds 0mA of input current
1 = Adds 512mA of input current
9
0 = Adds 0mA of input current
1 = Adds 1024mA of input current
10
11
12
0 = Adds 0mA of input current
1 = Adds 2048mA of input current
0 = Adds 0mA of input current
1 = Adds 4096mA of input current
0 = Adds 0mA of input current
1 = Adds 8192mA of input current, 11004mA max
13
14
15
Not used
Not used
Not used
FN6738.3
June 8, 2011
15
ISL88731A
Acknowledge). The master will then produce a Stop condition to
end the read transaction.
Charger Timeout
The ISL88731A includes 2 timers to insure the SMBus master is
active and to prevent overcharging the battery. ISL88731A will
terminate charging if the charger has not received a write to the
ChargeVoltage or ChargeCurrent register within 175s or if the
SCL line is low for more than 25ms. If a time-out occurs, either
ChargeVoltage or ChargeCurrent registers must be written to
re-enable charging.
ISL88731A does not support reading more than 1 register per
transaction.
Application Information
The following battery charger design refers to the ”Typical
Application Circuit” (see Figure 2) on page 2, where typical
battery configuration of 3S2P is used. This section describes how
to select the external components including the inductor, input
and output capacitors, switching MOSFETs and current sensing
resistors.
ISL88731A Data Byte Order
Each register in ISL88731A contains 16bits or 2, 8 bit bytes. All
data sent on the SMBus is in 8-bit bytes and 2 bytes must be
written or read from each register in ISL88731A. The order in
which these bytes are transmitted appears reversed from the
way they are normally written. The LOW byte is sent first and the
HI byte is sent second. For example, When writing 0x41A0, 0xA0
is written first and 0x41 is sent second.
Inductor Selection
The inductor selection has trade-offs between cost, size,
crossover frequency and efficiency. For example, the lower the
inductance, the smaller the size, but ripple current is higher. This
also results in higher AC losses in the magnetic core and the
windings, which decreases the system efficiency. On the other
hand, the higher inductance results in lower ripple current and
smaller output filter capacitors, but it has higher DCR (DC
resistance of the inductor) loss, lower saturation current and has
slower transient response. So, the practical inductor design is
based on the inductor ripple current being ±15% to ±20% of the
maximum operating DC current at maximum input voltage.
Writing to the Internal Registers
In order to set the charge current, charge voltage or input current,
valid 16-bit numbers must be written to ISL88731A’s internal
registers via the SMBus.
To write to a register in the ISL88731A, the master sends a
control byte with the R/W bit set to 0, indicating a write. If it
receives an Acknowledge from the ISL88731A it sends a register
address byte setting the register to be written (i.e. 0x14 for the
ChargeCurrent register). The ISL88731A will respond with an
Acknowledge. The master then sends the lower data byte to be
written into the desired register. The ISL88731A will respond with
an Acknowledge. The master then sends the higher data byte to
be written into the desired register. The ISL88731A will respond
with an Acknowledge. The master then issues a Stop condition,
indicating to the ISL88731A that the current transaction is
complete. Once this transaction completes, the ISL88731A will
begin operating at the new current or voltage.
Maximum ripple is at 50% duty cycle or V
= V /2. The
BAT
IN,MAX
required inductance for ±15% ripple current can be calculated
from Equation 3:
V
IN, MAX
⋅ 0.3 ⋅ I
L, MAX
------------------------------------------------------
L =
4 ⋅ F
(EQ. 3)
SW
Where, V
switching frequency and I
inductor.
is the maximum input voltage, F
is the
is the max DC current in the
IN,(MAX)
SW
L,(MAX)
For V
= 20V, V
= 12.6V, I
= 4.5A, and
BAT,(MAX)
IN,(MAX)
BAT
f = 400kHz, the calculated inductance is 9.3µH. Choosing the
s
closest standard value gives L = 10µH. Ferrite cores are often the
best choice since they are optimized at 400kHz to 600kHz
operation with low core loss. The core must be large enough not
ISL88731A does not support writing more than one register per
transaction.
to saturate at the peak inductor current I
in Equation 4:
Peak
Reading from the Internal
Registers
1
--
⋅ I
RIPPLE
I
= I
+
PEAK
L, MAX
2
(EQ. 4)
The ISL88731A has the ability to read from 5 internal registers.
Prior to reading from an internal register, the master must first
select the desired register by writing to it and sending the registers
address byte. This process begins by the master sending a control
byte with the R/W bit set to 0, indicating a write. Once it receives
an Acknowledge from the ISL88731A it sends a register address
byte representing the internal register it wants to read. The
ISL88731A will respond with an Acknowledge. The master must
then respond with a Stop condition. After the Stop condition, the
master follows with a new Start condition, then sends a new
control byte with the ISL88731A slave address and the R/W bit set
to 1, indicating a read. The ISL88731A will Acknowledge then
send the lower byte stored in that register. After receiving the byte,
the master Acknowledges by holding SDA low during the 9th clock
pulse. ISL88731A then sends the higher byte stored in the register.
After the second byte, neither device holds SDA low (No
Inductor saturation can lead to cascade failures due to very high
currents. Conservative design limits the peak and RMS current in
the inductor to less than 90% of the rated saturation current.
Crossover frequency is heavily dependent on the inductor value.
F
should be less than 20% of the switching frequency and a
CO
conservative design has F less than 10% of the switching
CO
frequency. The highest F is in voltage control mode with the
CO
battery removed and may be calculated (approximately) from
Equation 5:
5 ⋅ 11 ⋅ R
SENSE
---------------------------------------
=
F
CO
2π ⋅ L
(EQ. 5)
FN6738.3
June 8, 2011
16
ISL88731A
Although LGATE sink current (1.8A typical) is more than enough
Output Capacitor Selection
The output capacitor in parallel with the battery is used to absorb
the high frequency switching ripple current and smooth the
output voltage. The RMS value of the output ripple current I
is given by Equation 6:
to switch the FET off quickly, voltage drops across parasitic
impedances between LGATE and the MOSFET can allow the gate
to rise during the fast rising edge of voltage on the drain.
MOSFETs with low threshold voltage (<1.5V) and low ratio of
RMS
C
/C (<5) and high gate resistance (>4Ω) may be turned on
gs gd
V
for a few ns by the high dV/dt (rising edge) on their drain. This
IN, MAX
---------------------------------
I
=
⋅ D ⋅ (1 – D)
RMS
can be avoided with higher threshold voltage and C /C ratio.
gs gd
12 ⋅ L ⋅ F
(EQ. 6)
SW
Another way to avoid cross conduction is slowing the turn-on
speed of the high-side MOSFET by connecting a resistor between
the BOOT pin and the boot strap capacitor.
Where the duty cycle D is the ratio of the output voltage (battery
voltage) over the input voltage for continuous conduction mode
which is typical operation for the battery charger. During the
battery charge period, the output voltage varies from its initial
battery voltage to the rated battery voltage. So, the duty cycle
varies from 0.53 for the minimum battery voltage of 7.5V
(2.5V/Cell) to 0.88 for the maximum battery voltage of 12.6V.
The maximum RMS value of the output ripple current occurs at
the duty cycle of 0.5 and is expressed as Equation 7:
For the high-side MOSFET, the worst-case conduction losses
occur at the minimum input voltage, as shown in Equation 8:
V
2
OUT
------------
(EQ. 8)
P
=
⋅ I
⋅ r
BAT DS(ON)
Q1, conduction
V
IN
The optimum efficiency occurs when the switching losses equal
the conduction losses. However, it is difficult to calculate the
switching losses in the high-side MOSFET since it must allow for
difficult-to-quantify factors that influence the turn-on and turn-off
times. These factors include the MOSFET internal gate
V
IN, MAX
-----------------------------------------
I
=
RMS
4 ⋅ 12 ⋅ L ⋅ F
(EQ. 7)
SW
For V
= 19V, V
= 16.8V, L = 10µH, and f = 400kHz,
BAT s
IN,(MAX)
resistance, gate charge, threshold voltage, stray inductance and
the pull-up and pull-down resistance of the gate driver.
the maximum RMS current is 0.19A. A typical 20µF ceramic
capacitor is a good choice to absorb this current and also has
very small size. Organic polymer capacitors have high
capacitance with small size and have a significant equivalent
series resistance (ESR). Although ESR adds to ripple voltage, it
also creates a high frequency zero that helps the closed loop
operation of the buck regulator.
The following switching loss calculation (Equation 9) provides a
rough estimate.
P
=
Q1, Switching
Q
Q
gd
⎛
⎞
⎟
⎠
⎛
⎜
⎝
⎞
⎟
⎠
1
2
1
2
gd
--
-----------------------
--
----------------
V
I
f
+
V
I
f
+ Q V f
rr IN sw
⎜
⎝
IN LV sw
IN LP sw
I
I
EMI considerations usually make it desirable to minimize ripple
current in the battery leads. Beads may be added in series with
the battery pack to increase the battery impedance at 400kHz
switching frequency. Switching ripple current splits between the
battery and the output capacitor depending on the ESR of the
output capacitor and battery impedance. If the ESR of the output
capacitor is 10mΩ and battery impedance is raised to 2Ω with a
bead, then only 0.5% of the ripple current will flow in the battery.
g, source
g, sink
(EQ. 9)
Where, the following are the peak gate-drive source/sink current
of Q , respectively:
1
• Q : drain-to-gate charge,
gd
• Q : total reverse recovery charge of the body-diode in low-side
rr
MOSFET,
• I : inductor valley current,
LV
MOSFET Selection
• I : Inductor peak current,
LP
The Notebook battery charger synchronous buck converter has
the input voltage from the AC-adapter output. The maximum
AC-adapter output voltage does not exceed 25V. Therefore, 30V
logic MOSFET should be used.
• I
g,sink
• I ,
g source
Low switching loss requires low drain-to-gate charge Q
gd
.
Generally, the lower the drain-to-gate charge, the higher the
ON-resistance. Therefore, there is a trade-off between the
ON-resistance and drain-to-gate charge. Good MOSFET selection
is based on the Figure of Merit (FOM), which is a product of the
total gate charge and ON-resistance. Usually, the smaller the
value of FOM, the higher the efficiency for the same application.
The high-side MOSFET must be able to dissipate the conduction
losses plus the switching losses. For the battery charger
application, the input voltage of the synchronous buck converter
is equal to the AC-adapter output voltage, which is relatively
constant. The maximum efficiency is achieved by selecting a
high-side MOSFET that has the conduction losses equal to the
switching losses. Switching losses in the low-side FET are very
small. The choice of low-side FET is a trade-off between
For the low-side MOSFET, the worst-case power dissipation
occurs at minimum battery voltage and maximum input voltage
(Equation 10):
conduction losses (r
) and cost. A good rule of thumb for
DS(ON)
of the low-side FET is 2x the r
the r
FET.
of the high-side
DS(ON)
DS(ON)
V
⎛
⎜
⎝
⎞
⎟
⎠
2
OUT
------------
P
=
1 –
⋅ I
⋅ r
BAT DS(ON)
Q2
V
IN
(EQ. 10)
The LGATE gate driver can drive sufficient gate current to switch
most MOSFETs efficiently. However, some FETs may exhibit cross
conduction (or shoot-through) due to current injected into the
Choose a low-side MOSFET that has the lowest possible
ON-resistance with a moderate-sized package like the SO-8 and
is reasonably priced. The switching losses are not an issue for the
low-side MOSFET because it operates at zero-voltage-switching.
drain-to-source parasitic capacitor (C ) by the high dV/dt rising
gd
edge at the phase node when the high-side MOSFET turns on.
FN6738.3
June 8, 2011
17
ISL88731A
Ensure that the required total gate drive current for the selected
MOSFETs should be less than 24mA. So, the total gate charge for
the high-side and low-side MOSFETs is limited by Equation 11:
Diagram” (see Figure 1) on page 2. These three loops will be
described separately.
Transconductance Amplifiers GMV, GMI and
GMS
ISL88731A uses several transconductance amplifiers (also
known as gm amps). Most commercially available op amps are
voltage controlled voltage sources with gain expressed as
I
GATE
--------------
Q
≤
GATE
f
(EQ. 11)
sw
Where I
is the total gate drive current and should be less
than 24mA. Substituting I = 24mA and f = 400kHz into
GATE
GATE
s
Equation 11 yields that the total gate charge should be less than
80nC. Therefore, the ISL88731A easily drives the battery charge
current up to 8A.
A = V
/V . gm amps are voltage controlled current sources
/V . gm will appear in some of
OUT IN
with gain expressed as gm = I
OUT IN
the equations for poles and zeros in the compensation.
PWM Gain F
m
Snubber Design
The Pulse Width Modulator in the ISL88731A converts voltage at
VCOMP to a duty cycle by comparing VCOMP to a triangle wave
ISL88731A's buck regulator operates in discontinuous current
mode (DCM) when the load current is less than half the
peak-to-peak current in the inductor. After the low-side FET turns
off, the phase voltage rings due to the high impedance with both
FETs off. This can be seen in Figure 9. Adding a snubber (resistor
in series with a capacitor) from the phase node to ground can
greatly reduce the ringing. In some situations a snubber can
improve output ripple and regulation.
(duty = VCOMP/V
). The low-pass filter formed by L and
convert the duty cycle to a DC output voltage
P-P RAMP
C
O
(Vo = V
*duty). In ISL88731A, the triangle wave amplitude is
proportional to V . Making the ramp amplitude proportional
DCIN
DCIN
to DCIN makes the gain from VCOMP to the PHASE output a
constant 11 and is independent of DCIN. For small signal AC
analysis, the battery is modeled by its internal resistance. The
total output resistance is the sum of the sense resistor and the
internal resistance of the MOSFETs, inductor and capacitor.
Figure 20 shows the small signal model of the pulse width
modulator (PWM), power stage, output filter and battery.
The snubber capacitor should be approximately twice the
parasitic capacitance on the phase node. This can be estimated
by operating at very low load current (100mA) and measuring the
ringing frequency.
C
C
and R
can be calculated from Equations 12 and 13:
SNUB
SNUB
2
2 ⋅ L
-----------------------------------
VDD
=
R
=
-----------------
SNUB
SNUB
2
SNUB
C
(2πF
)
⋅ L
ring
RAMP GEN
VRAMP = VDD/11
(EQ. 13)
(EQ. 12)
L
Input Capacitor Selection
-
The input capacitor absorbs the ripple current from the
synchronous buck converter, which is given by Equation 14:
+
CO
PWM
INPUT
V
(V – V
)
OUT
OUT IN
(EQ. 14)
--------------------------------------------------
I
= I
BAT
rms
V
IN
This RMS ripple current must be smaller than the rated RMS
current in the capacitor datasheet. Non-tantalum chemistries
(ceramic, aluminum, or OSCON) are preferred due to their
resistance to power-up surge currents when the AC-adapter is
plugged into the battery charger. For Notebook battery charger
applications, it is recommended that ceramic capacitors or
polymer capacitors from Sanyo be used due to their small size
and reasonable cost.
PWM
GAIN=11
L
RSENSE
11
RFET_RDSON
RL_DCR
CO
RBAT
PWM
INPUT
RESR
Loop Compensation Design
FIGURE 20. SMALL SIGNAL AC MODEL
ISL88731A has three closed loop control modes. One controls
the output voltage when the battery is fully charged or absent. A
second controls the current into the battery when charging and
the third limits current drawn from the adapter. The charge
current and input current control loops are compensated by a
single capacitor on the ICOMP pin. The voltage control loop is
compensated by a network on the VCOMP pin. Descriptions of
these control loops and guidelines for selecting compensation
components will be given in the following sections. Which loop
controls the output is determined by the minimum current buffer
and the minimum voltage buffer shown in the “Functional Block
In most cases the Battery resistance is very small (<200mΩ)
resulting in a very low Q in the output filter. This results in a
frequency response from the input of the PWM to the inductor
current with a single pole at the frequency calculated in
Equation 15:
(R
+ r
+ R
+ R
)
BAT
SENSE
DS(ON)
DCR
---------------------------------------------------------------------------------------------
=
F
POLE1
2π ⋅ L
(EQ. 15)
FN6738.3
June 8, 2011
18
ISL88731A
The output capacitor creates a pole at a very high frequency due
to the small resistance in parallel with it. The frequency of this
pole is calculated in Equation 16:
A filter should be added between RS2 and CSOP and CSON to
reduce switching noise. The filter roll-off frequency should be
between the crossover frequency and the switching frequency
(~100kHz). RF2 should be small (<10Ω) to minimize offsets due
to leakage current into CSOP. The filter cut off frequency is
calculated using Equation 19:
1
-----------------------------------
F
=
POLE2
2π ⋅ C ⋅ R
o
BAT
(EQ. 16)
1
----------------------------------------
F
=
Charge Current Control Loop
FILTER
(2π ⋅ C ⋅ R
)
F2
F2
(EQ. 19)
When the battery is less than the fully charged, the voltage error
amplifier goes to it’s maximum output (limited to 0.3V above
ICOMP) and the ICOMP voltage controls the loop through the
minimum voltage buffer. Figure 22 shows the charge current
control loop.
The crossover frequency is determined by the DC gain of the
modulator and output filter and the pole in Equation 16. The DC
gain is calculated in Equation 20 and the crossover frequency is
calculated with Equation 21:
The compensation capacitor (C
) gives the error amplifier
11 ⋅ R
ICOMP
SENSE
---------------------------------------------------------------------------------------------
=
A
(GMI) a pole at a very low frequency (<<1Hz) and a a zero at FZ1
FZ1 is created by the 0.25*CA2 output added to ICOMP. The
frequency can be calculated from Equation 17:
.
DC
(R
+ r
+ R
+ R
)
BAT
SENSE
DS(ON)
DCR
(EQ. 20)
11 ⋅ R
SENSE
2π ⋅ L
-------------------------------
=
F
= A ⋅ F
CO
DC POLE
4 ⋅ gm2
(EQ. 21)
------------------------------------
=
F
gm2 = 50μA ⁄ V
ZERO
(2π ⋅ C
)
ICOMP
(EQ. 17)
The Bode plot of the loop gain, the compensator gain and the
power stage gain is shown in Figure 22.
L
PHASE
Adapter Current Limit Control Loop
11
If the combined battery charge current and system load current
draws current that equals the adapter current limit set by the
InputCurrent register, ISL88731A will reduce the current to the
battery and/or reduce the output voltage to hold the adapter
current at the limit. Above the adapter current limit, the
minimum current buffer equals the output of GMS and ICOMP
controls the charger output. Figure 23 shows the adapter current
limit control loop.
RFET_RDSON
RL_DCR
CA2
R
+
CSOP
F2
0.25
+
S
Σ
20X
-
C
F2
R
S2
-
CSON
ICOMP
-
GMI
R
BAT
CO
DACI
+
60
Compensator
CICOMP
RESR
Modulator
40
20
0
Loop
F
ZERO
FIGURE 21. CHARGE CURRENT LIMIT LOOP
Placing this zero at a frequency equal to the pole calculated in
Equation 16 will result in maximum gain at low frequencies and
phase margin near 90°. If the zero is at a higher frequency
(smaller C
), the DC gain will be higher but the phase
ICOMP
margin will be lower. Use a capacitor on ICOMP that is equal to or
greater than the value calculated in Equation 18. The factor of
1.5 is to ensure the zero is at a frequency lower than the pole
including tolerance variations.
-20
-40
-60
F
F
F
FILTER
POLE1
POLE2
1.5 ⋅ 4 ⋅ (50μA ⁄ V) ⋅ L
---------------------------------------------------------------------------------------------
=
C
ICOMP
(R
+ r
+ R
+ R
)
BAT
SENSE
DS(ON)
DCR
0.01
0.1
1
10
100
1000
(EQ. 18)
FREQUENCY (kHz)
FIGURE 22. CHARGE CURRENT LOOP BODE PLOTS
FN6738.3
June 8, 2011
19
ISL88731A
L
DCIN
PHASE
11
L
PHASE
RFET_RDSON
RS1
RL_DCR
RFET_RDSON
11
RL_DCR
RF1
CA2
RF2
+
0.25
CSOP
CSON
CF1
Σ
CA2
+
RF2
CSOP
CSON
+
-
0.25
20x
+
Σ
CF2
RS2
20X
-
-
CF2
RS2
-
CSSN
CSSP
R3
-
+
VCOMP
20
RBAT
-
CO
CO
RESR
RBAT
GMV
CA1
+
R4
RESR
CVCOMP
RVCOMP
-
+
GMS
DACV
DACS
ICOMP
CICOMP
FIGURE 24. VOLTAGE CONTROL LOOP
FIGURE 23. ADAPTER CURRENT LIMIT CONTROL LOOP
The loop response equations, bode plots and the selection of
CICOMP are the same as the charge current control loop with loop
Output LC Filter Transfer Functions
The gain from the phase node to the system output and battery
depend entirely on external components. Typical output LC filter
response is shown in Figure 25. Transfer function ALC(s) is shown
in Equation 22:
gain reduced by the duty cycle and the ratio of R /R . In other
S1 S2
words, if R = R and the duty cycle D = 50%, the loop gain will
S1 S2
be 6dB lower than the loop gain in Figure 23. This gives lower
crossover frequency and higher phase margin in this mode. If
s
R
/R = 2 and the duty cycle is 50% then the adapter current
⎛
⎝
⎞
⎠
S1 S2
-------------
1 –
ω
loop gain will be identical to the gain in Figure 23.
ESR
--------------------------------------------------------
A
=
LC
2
⎛
⎜
⎝
⎞
s
ω
s
A filter should be added between RS1 and CSIP and CSIN to
reduce switching noise. The filter roll off frequency should be
between the crossover frequency and the switching frequency
(~100kHz).
---------- -----------------------
+
+ 1
⎟
⎠
(ω ⋅ Q)
LC
DP
1
L
C
o
1
----------------------
=
ω
Q = R
⋅
-----
-----------------------------
ω
=
LC
o
ESR
(R
⋅ C )
( L ⋅ C )
o
ESR
o
Voltage Control Loop
(EQ. 22)
When the battery is charged to the voltage set by ChargeVoltage
register the voltage error amplifier (GMV) takes control of the
output (assuming that the adapter current is below the limit set
by ACLIM). The voltage error amplifier (GMV) discharges the
capacitor on VCOMP to limit the output voltage. The current to
the battery decreases as the cells charge to the fixed voltage and
the voltage across the internal battery resistance decreases. As
battery current decreases the two current error amplifiers (GMI
and GMS) output their maximum current and charge the
capacitor on ICOMP to its maximum voltage (limited to 0.3V
above VCOMP). With high voltage on ICOMP, the minimum
voltage buffer output equals the voltage on VCOMP.
The resistance RO is a combination of MOSFET r
, inductor
DS(ON)
DCR, R
and the internal resistance of the battery (normally
SENSE
between 50mΩ and 200mΩ) The worst case for voltage mode
control is when the battery is absent. This results in the highest Q
of the LC filter and the lowest phase margin.
The compensation network consists of the voltage error amplifier
GMV and the compensation network R which give
, C
VCOMP VCOMP
the loop very high DC gain, a very low frequency pole and a zero
at F . Inductor current information is added to the feedback
ZERO1
to create a second zero F
. The low pass filter R , C
ZERO2 F2 F2
between R and ISL88731A add a pole at F
. R and R
3 4
S2 FILTER
are internal divider resistors that set the DC output voltage. For a
The voltage control loop is shown in Figure 24.
3-cell battery, R = 500kΩ and R = 100kΩ. Equations 23
3
4
through 30 relate the compensation network’s poles, zeros and
gain to the components in Figure 24. Figure 26 shows an
asymptotic Bode plot of the DC/DC converter’s gain vs frequency.
It is strongly recommended that FZERO1 is approximately 30% of
FLC and FZERO2 is approximately 70% of FLC.
FN6738.3
June 8, 2011
20
ISL88731A
Compensation Break Frequency Equations
1
-----------------------------------------------------------------
F
F
F
=
NO BATTERY
ZERO1
ZERO2
(2π ⋅ C
⋅ R
)
VCOMP
1COMP
(EQ. 23)
R
BATTERY
R
R
⎛
⎜
⎝
⎞
⎟
⎠
⎛
⎜
⎝
⎞
⎟
⎠
gm1
5
VCOMP
4
= 200mΩ
⎛
⎝
⎞
⎠
------------------------------------------
--------------------
------------
=
⋅
⋅
2π ⋅ R
⋅ C
R
+ R
3
R
BATTERY
SENSE
4
o
= 50mΩ
(EQ. 24)
(EQ. 25)
1
------------------------------
=
LC
(2π L ⋅ C )
o
1
----------------------------------------
F
F
=
=
FILTER
POLE1
(2π ⋅ R ⋅ C
)
F2
(EQ. 26)
(EQ. 27)
F2
1
-----------------------------------------------
(2π ⋅ R
⋅ C )
o
SENSE
1
-----------------------------------------
F
=
ESR
(2π ⋅ C ⋅ R
)
ESR
(EQ. 28)
o
Choose R
VCOMP
Equation 29.
equal or lower than the value calculated from
FREQUENCY
FIGURE 25. FREQUENCY RESPONSE OF THE LC OUTPUT FILTER
R
+ R
4
R
4
⎛
⎜
⎝
⎞
⎟
⎠
5
gm1
3
⎛
⎝
⎞
⎠
------------
--------------------
R
= (0.7 ⋅ F ) ⋅ (2π ⋅ C ⋅ R ) ⋅
SENSE
⋅
VCOMP
LC
o
(EQ. 29)
60
Next choose C
from Equation 30.
equal or higher than the value calculated
VCOMP
Compensator
Modulator
40
20
1
Loop
----------------------------------------------------------------------
=
C
VCOMP
FPOLE1
FFILTER
ESR
(0.3 ⋅ F ) ⋅ (2π ⋅ R
)
VCOMP
LC
(EQ. 30)
F
LC
PCB Layout Considerations
Power and Signal Layers Placement on the
PCB
As a general rule, power layers should be close together, either
on the top or bottom of the board, with signal layers on the
opposite side of the board. As an example, layer arrangement on
a 4-layer board is shown below:
0
-20
-40
-60
F
ZERO1
F
ZERO2
F
1. Top Layer: signal lines, or half board for signal lines and the
other half board for power lines
0.1
1
10
FREQUENCY (kHz)
100
1000
2. Signal Ground
FIGURE 26. ASYMPTOTIC BODE PLOT OF THE VOLTAGE CONTROL
LOOP GAIN
3. Power Layers: Power Ground
4. Bottom Layer: Power MOSFET, Inductors and other Power
traces
Separate the power voltage and current flowing path from the
control and logic level signal path. The controller IC will stay on
the signal layer, which is isolated by the signal ground to the
power signal traces.
Component Placement
The power MOSFET should be close to the IC so that the gate
drive signal, the LGATE, UGATE, PHASE, and BOOT, traces can be
short.
Place the components in such a way that the area under the IC
has less noise traces with high dv/dt and di/dt, such as gate
signals and phase node signals.
FN6738.3
June 8, 2011
21
ISL88731A
Signal Ground and Power Ground Connection
At minimum, a reasonably large area of copper, which will shield
other noise couplings through the IC, should be used as signal
ground beneath the IC. The best tie-point between the signal
ground and the power ground is at the negative side of the output
capacitor on each side, where there is little noise; a noisy trace
beneath the IC is not recommended.
SENSE
RESISTOR
HIGH
CURRENT
TRACE
HIGH
CURRENT
TRACE
KELVIN CONNECTION TRACES
TO THE LOW PASS FILTER AND
CSOP AND CSON
GND and VCC Pin
At least one high quality ceramic decoupling capacitor should be
used to cross these two pins. The decoupling capacitor can be
put close to the IC.
FIGURE 27. CURRENT SENSE RESISTOR LAYOUT
CSOP, CSON, CSSP and CSSN Pins
LGATE Pin
Accurate charge current and adapter current sensing is critical
for good performance. The current sense resistor connects to the
CSON and the CSOP pins through a low pass filter with the filter
capacitor very near the IC (see Figure 2). Traces from the sense
resister should start at the pads of the sense resister and should
be routed close together, through the low pass filter and to the
CSOP and CSON pins (see Figure 27). The CSON pin is also used
as the battery voltage feedback. The traces should be routed
away from the high dv/dt and di/dt pins like PHASE, BOOT pins.
In general, the current sense resistor should be close to the IC.
These guidelines should also be followed for the adapter current
sense resister and CSSP and CSSN. Other layout arrangements
should be adjusted accordingly.
This is the gate drive signal for the bottom MOSFET of the buck
converter. The signal going through this trace has both high dv/dt
and high di/dt, and the peak charging and discharging current is
very high. These two traces should be short, wide, and away from
other traces. There should be no other traces in parallel with
these traces on any layer.
PGND Pin
PGND pin should be laid out to the negative side of the relevant
output capacitor with separate traces.The negative side of the
output capacitor must be close to the source node of the bottom
MOSFET. This trace is the return path of LGATE.
PHASE Pin
DCIN Pin
This trace should be short, and positioned away from other weak
signal traces. This node has a very high dv/dt with a voltage
swing from the input voltage to ground. No trace should be in
parallel with it. This trace is also the return path for UGATE.
Connect this pin to the high-side MOSFET source.
This pin connects to AC-adapter output voltage, and should be
less noise sensitive.
Copper Size for the Phase Node
The capacitance of PHASE should be kept very low to minimize
ringing. It would be best to limit the size of the PHASE node
copper in strict accordance with the current and thermal
management of the application.
UGATE Pin
This pin has a square shape waveform with high dv/dt. It
provides the gate drive current to charge and discharge the top
MOSFET with high di/dt. This trace should be wide, short, and
away from other traces, similar to the LGATE.
Identify the Power and Signal Ground
The input and output capacitors of the converters, the source
terminal of the bottom switching MOSFET PGND should connect
to the power ground. The other components should connect to
signal ground. Signal and power ground are tied together at one
point.
BOOT Pin
This pin’s di/dt is as high as the UGATE; therefore, this trace
should be as short as possible.
Clamping Capacitor for Switching MOSFET
It is recommended that ceramic capacitors be used closely
connected to the drain of the high-side MOSFET, and the source
of the low-side MOSFET. This capacitor reduces the noise and the
power loss of the MOSFET.
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6738.3
June 8, 2011
22
ISL88731A
Package Outline Drawing
L28.5x5B
28 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 1, 10/07
4X
3.0
5.00
0.50
24X
A
6
B
PIN #1 INDEX AREA
28
22
6
PIN 1
INDEX AREA
1
21
3 .25 ± 0 . 10
15
7
(4X)
0.15
8
14
0.10 M C A B
4
28X 0.25 ± 0.05
TOP VIEW
28X 0.55 ± 0.05
BOTTOM VIEW
SEE DETAIL "X"
C
0.10
0 . 75 ± 0.05
C
BASE PLANE
SEATING PLANE
0.08
C
( 4. 65 TYP )
(
( 24X 0 . 50)
SIDE VIEW
3. 25)
(28X 0 . 25 )
( 28X 0 . 75)
5
C
0 . 2 REF
0 . 00 MIN.
0 . 05 MAX.
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
Tiebar shown (if present) is a non-functional feature.
5.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN6738.3
June 8, 2011
23
ISL88731AHRZ-T7 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| ISL88731C | INTERSIL | SMBus Level 2 Battery Charger | 获取价格 |
|
| ISL88731CEVAL2Z | INTERSIL | SMBus Level 2 Battery Charger | 获取价格 |
|
| ISL88731CHRTZ | INTERSIL | SMBus Level 2 Battery Charger | 获取价格 |
|
| ISL88731CHRTZ-T13 | RENESAS | Power Supply Support Circuit | 获取价格 |
|
| ISL88731CHRTZ-T7 | RENESAS | Power Supply Support Circuit | 获取价格 |
|
| ISL88731HRZ | INTERSIL | SMBus Level 2 Battery Charger | 获取价格 |
|
| ISL88731HRZ-13 | RENESAS | Power Supply Support Circuit | 获取价格 |
|
| ISL88731HRZ-7 | RENESAS | Power Supply Support Circuit | 获取价格 |
|
| ISL88731HRZ-T | INTERSIL | SMBus Level 2 Battery Charger | 获取价格 |
|
| ISL88732 | RENESAS | SMBus Level 2 Battery Charger with Boost Mode | 获取价格 |
|
ISL88731AHRZ-T7 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 6
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 9
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
