ISL91117II7Z-T7A [RENESAS]
High Efficiency Synchronous Boost Converter with 4.2A Switches and Output Disconnect;![ISL91117II7Z-T7A](http://pdffile.icpdf.com/pdf2/p00327/img/icpdf/ISL91117_2009281_icpdf.jpg)
型号: | ISL91117II7Z-T7A |
厂家: | ![]() |
描述: | High Efficiency Synchronous Boost Converter with 4.2A Switches and Output Disconnect 开关 |
文件: | 总12页 (文件大小:806K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
DATASHEET
ISL91117
FN8569
Rev 3.00
March 7, 2014
High Efficiency Synchronous Boost Converter with 4.2A Switches and Output
Disconnect
The ISL91117 is a highly-integrated boost switching regulator
Features
for battery powered applications. The device provides a power
supply solution for products using dual-cell or three-cell
alkaline, NiCd or NiMH, or one-cell Li-ion or Li-polymer battery.
• Input voltage range: 1.8V to 4.8V
• Fixed 5V or adjustable output
• Output current: up to 1.5A (PVIN = 3.3V, VOUT = 5V)
• High efficiency: up to 96%
This device is capable of delivering an output current of 1.5A
with PVIN = 3.3V and VOUT = 5V. The use of a synchronous
rectifier maximizes efficiency at high loads. No-load quiescent
current of only 35µA optimizes efficiency under light-load
conditions. Forced PWM and/or synchronization to an external
clock may also be selected for noise sensitive applications.
• 35µA quiescent current maximizes light-load efficiency
• True input-output disconnect when disabled
• 2.6MHz switching frequency minimizes external component
size
The ISL91117 is designed for standalone applications and
supports 5V fixed output voltage or variable output voltages
with an external resistor divider. Power supply solution size is
minimized by a 2.34mm x 1.72mm WLCSP and a 2.6MHz
switching frequency, which allows for the use of tiny,
low-profile inductors and ceramic capacitors to minimize the
size of the solution.
• Selectable forced-PWM mode and external synchronization
• Fully protected for short-circuit, over-temperature and
undervoltage
• Small 2.34mm x 1.72mm WLCSP
Applications
• Smart phones and tablets
Related Literature
• AN1918, ISL91117II7-EVZ, ISL91117IIA-EVZ Evaluation
Boards
• Wireless communication devices
• Products including portable HDMI and USB-OTG
L1 1µH
100
VIN = 4.2V
95
90
VIN =
1.8V TO 4.8V
BLKG
PVIN
85
VIN = 3.6V
80
VOUT = 5V
VIN = 3.0V
C1
22µF
VOUT
FB
75
VIN = 2.7V
ISL91117
VIN
EN
70
65
60
55
50
C2
2x22µF
MODE
0.1
1
10
100
1000
LOAD CURRENT (mA)
FIGURE 1. TYPICAL FIXED OUTPUT APPLICATION
FIGURE 2. EFFICIENCY vs LOAD CURRENT (VOUT = 5V)
FN8569 Rev 3.00
March 7, 2014
Page 1 of 12
ISL91117
Block Diagram
BLKG
LX
A2 B2 C2
B4 C4
A4
A1
A5
B5
C5
PVIN
VOUT
PGND
B1
C1
Blocking FET
GATE
SOFT
DISCHARGE
DRIVERS
& ANTI-
SHOOT THRU
EN
EN
D2
D1
A3
B3
C3
EN
VIN
VREF
PVIN
MONITOR
VOUT
CLAMP
THERMAL
SHUTDOWN
PWM
CONTROL
CURRENT
DETECT
MODE
D3
EN
VOUT
MONITOR
EN
OSC
FB
D5
EN
PWM
REF
COMP
ERROR
AMP
VOLTAGE
PROG.
D4
GND
Pin Configuration
Pin Descriptions
ISL91117
PIN
(4x5 WLCSP)
TOP VIEW
PIN #
NAMES
DESCRIPTION
A5, B5, C5 VOUT Boost output. Connect 2x22µF capacitor to
PGND.
A1
B1 C1
D1
A4, B4, C4
LX
Switching node of the boost converter.
A2
A3
A4
C2
C3
D2
D3
D4
D5
B2
B3
A3, B3, C3 PGND Power ground for high switching current.
A2, B2, C2 BLKG Blocking FET terminal. Connect the input side of
the inductor.
B4 C4
B5 C5
A1, B1, C1
PVIN Power input. Range: 1.8V to 4.8V. Connect a 22µF
capacitor to PGND.
A5
D1
D2
D3
VIN
EN
Supply input. Range: 1.8V to 4.8V.
Logic input, drive HIGH to enable device.
MODE Logic input, HIGH for auto PFM mode. LOW for
forced PWM operation. Also, this pin can be used
with an external clock sync input. Range:
2.75MHz to 3.25MHz. Maximum voltage on this
pin should be limited to VIN.
D4
D5
GND Analog ground pin.
FB
Voltage feedback pin.
FN8569 Rev 3.00
March 7, 2014
Page 2 of 12
ISL91117
Ordering Information
PART NUMBER
PART
VOUT
(V)
TEMP RANGE
(°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
(Notes 1, 2, 3)
MARKING
ISL91117II7Z-T (Note 4)
ISL91117II7Z-T7A (Note 4)
ISL91117IIAZ-T
GAXC
5
-40 to +85
-40 to +85
-40 to +85
-40 to +85
20 Ball WLCSP
W4x5.20F
W4x5.20F
W4x5.20F
W4x5.20F
GAXC
GAXB
GAXB
5
20 Ball WLCSP
20 Ball WLCSP
20 Ball WLCSP
ADJ.
ADJ.
ISL91117IIAZ-T7A
ISL91117II7-EVZ (Note 4)
ISL91117IIA-EVZ
Evaluation Board for ISL91117II7Z
Evaluation Board for ISL91117IIAZ
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free WLCSP and BGA packaged products employ special Pb-free material sets; molding compounds/die attach materials and
SnAgCu - e1 solder ball terminals, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free
WLCSP and BGA packaged products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL91117 For more information on MSL please see techbrief TB363.
4. Contact Intersil for Availability.
FN8569 Rev 3.00
March 7, 2014
Page 3 of 12
ISL91117
Absolute Maximum Ratings
Thermal Information
PVIN, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V
LX (Note 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V
FB (ISL91117IIAZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.7V
FB (ISL91117II7Z) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V
MODE/SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VIN+0.3V
GND, PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 0.3V
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V
ESD Rating
Thermal Resistance (Typical)
20 Ball WLCSP (Notes 5, 6). . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+125°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
JA (°C/W)
66
JC (°C/W)
1.0
Recommended Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 4.8V
Load Current Range (DC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A to 1.5A
Human Body Model (Tested per JESD22-A114E). . . . . . . . . . . . . . .2.5kV
Machine Model (Tested per JESD22-A115-A). . . . . . . . . . . . . . . . . . 200V
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
JA
Brief TB379
6. For , the “case temp” location is taken at the package top center.
JC
7. LX pin can withstand switching transients of -1.5V for 100ns, and 7V for 20ms.
Analog Specifications VIN = PVIN = EN = 3.6V, VOUT = 5V, L1 = 1µH, C1 = 22µF, C2 = 2 x 22µF, T = +25°C. Boldface limits apply over
A
the operating temperature range, -40°C to +85°C and input voltage range (1.8V to 4.8V).
MIN
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
(Note 8) TYP (Note 8) UNITS
POWER SUPPLY
VIN
Input Voltage Range
1.8
4.8
V
V
V
VIN Undervoltage Lockout Threshold
Rising
Falling
1.725 1.775
UVLO
1.550 1.650
V
I
VIN Supply Current
PFM mode, no external load on VOUT (Note 9)
EN = GND, VIN = 3.6V
27.5
0.4
60
µA
µA
VIN
I
VIN Supply Current, Shutdown
1.0
SD
OUTPUT VOLTAGE REGULATION
Output Voltage Accuracy
I
I
= 0mA, PWM mode
= 1mA, PFM mode
-2
-3
+2
+4
%
%
OUT
OUT
V
FB Pin Voltage Regulation
FB Pin Bias Current
For adjustable output version (ISL91117IIAZ)
For adjustable output version (ISL91117IIAZ)
0.788
0.80
0.812
0.2
V
FB
I
µA
FB
VOUT/ Line Regulation, PWM Mode
VIN
I
= 500mA, MODE = GND, VIN step from 2.3V to 4.8V
±0.005
±0.005
±12.5
±0.4
mV/mV
OUT
VOUT/ Load Regulation, PWM Mode
VIN = 3.7V, MODE = GND, IOUT step from 0mA to 500mA
mV/mA
mV/V
I
OUT
VOUT/ Line Regulation, PFM Mode
VIN
I
= 100mA, MODE = VIN, VIN step from 2.3V to 4.8V
OUT
VOUT/ Load Regulation, PFM Mode
VIN = 3.7V, MODE = VIN, I
Rising
step from 0mA to 100mA
mV/mA
OUT
I
OUT
V
Output Voltage Clamp
5.25
5.95
V
CLAMP
Output Voltage Clamp Hysteresis
400
mV
DC/DC SWITCHING SPECIFICATIONS
f
Oscillator Frequency
Minimum On Time
2.4
2.6
80
2.9
MHz
ns
SW
t
ONMIN
INFETLEAK LX Pin Leakage Current
-0.5
+0.5
µA
FN8569 Rev 3.00
March 7, 2014
Page 4 of 12
ISL91117
Analog Specifications VIN = PVIN = EN = 3.6V, VOUT = 5V, L1 = 1µH, C1 = 22µF, C2 = 2 x 22µF, T = +25°C. Boldface limits apply over
A
the operating temperature range, -40°C to +85°C and input voltage range (1.8V to 4.8V). (Continued)
MIN
MAX
SYMBOL
PARAMETER
TEST CONDITIONS
(Note 8) TYP (Note 8) UNITS
SOFT-START and SOFT DISCHARGE
t
Soft-start Time
Time from when EN signal asserts to when output voltage
ramp starts.
1
2
ms
ms
SS
Time from when output voltage ramp starts to when
output voltage reaches 95% of its nominal value.
VIN = 2V, I
= 200mA
OUT
R
VOUT Soft-Discharge ON-Resistance
EN < VIL
120
Ω
DISCHG
POWER MOSFET
R
R
P-Channel MOSFET ON-Resistance
N-Channel MOSFET ON-Resistance
P-Channel MOSFET Peak Current Limit
I
I
= 200mA
= 200mA
90
75
mΩ
mΩ
A
DSON_P
DSON_N
PK_LMT
OUT
OUT
I
3.7
4.2
4.7
PFM/PWM TRANSITION
Load Current Threshold, PFM to PWM
200
75
mA
mA
MHz
°C
Load Current Threshold, PWM to PFM
External Synchronization Frequency Range
Thermal Shutdown
2.75
3.25
150
35
Thermal Shutdown Hysteresis
°C
LOGIC INPUTS
I
Input Leakage
0.03
0.5
0.4
µA
V
LEAK
V
Input HIGH Voltage
Input LOW Voltage
IH
1.4
V
V
IL
NOTES:
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
9. Quiescent current measurements are taken when the output is not switching.
FN8569 Rev 3.00
March 7, 2014
Page 5 of 12
ISL91117
Typical Performance Curves
100
90
80
70
60
50
40
30
20
10
0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
VIN = 2.7V
VIN = 3.0V
VIN = 3.6V
VIN = 4.2V
0.1
1
10
100
1000
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
LOAD CURRENT (mA)
VIN (V)
FIGURE 4. EFFICIENCY vs LOAD CURRENT
(VOUT = 5V, MODE = LOW, T = +25°C)
FIGURE 3. MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE (V
= 5V)
OUT
A
100
140
130
120
110
100
90
LOAD = 500mA
95
LOAD = 100mA
90
LOAD = 10mA
LOAD = 1000mA
85
80
75
70
65
60
+85°C
+25°C
80
70
60
-40°C
4.3
1.8
2.3
2.8
3.3
3.8
4.3
4.8
1.8
2.3
2.8
3.3
3.8
4.8
VIN (V)
VIN (V)
FIGURE 5. EFFICIENCY vs INPUT VOLTAGE (MODE = HIGH, T = +25°C)
A
FIGURE 6. INPUT CURRENT vs INPUT VOLTAGE (MODE = HIGH)
30
5.01
VIN = 4.2V
VIN = 2.7V
5.00
4.99
4.98
25
-40°C
+85°C
20
+25°C
15
10
VIN = 3.0V
VIN = 3.6V
4.97
4.96
5
0
4.95
4.94
1.8
2.3
2.8
3.3
3.8
4.3
4.8
0.1
1
10
100
1000
VIN (V)
LOAD CURRENT (mA)
FIGURE 7. INPUT CURRENT vs INPUT VOLTAGE (MODE = LOW)
FIGURE 8. OUTPUT VOLTAGE vs LOAD CURRENT
(MODE = HIGH, T = +25°C)
A
FN8569 Rev 3.00
March 7, 2014
Page 6 of 12
ISL91117
Typical Performance Curves (Continued)
5.00
4.99
4.98
4.97
5.02
5.01
5.00
4.99
4.98
4.97
4.96
4.95
4.94
4.93
LOAD = 100mA
VIN = 4.2V
VIN = 2.7V
4.96
4.95
4.94
4.93
4.92
4.91
4.90
LOAD = 10mA
LOAD = 500mA
VIN = 3.6V
VIN = 3.0V
LOAD = 1000mA
1.8
2.3
2.8
3.3
3.8
4.3
4.8
1
10
100
LOAD CURRENT (mA)
1000
VIN (V)
FIGURE 10. OUTPUT VOLTAGE vs INPUT VOLTAGE
(MODE = HIGH, TA = +25°C)
FIGURE 9. OUTPUT VOLTAGE vs LOAD CURRENT
(MODE = LOW, T = +25°C)
A
LX (5V/DIV)
LX (5V/DIV)
INDUCTOR CURRENT
(500mA/DIV)
INDUCTOR CURRENT
(500mA/DIV)
VOUT, 5V OFFSET
(20mV/DIV)
VOUT, 5V OFFSET
(20mV/DIV)
TIMESCALE (2µs/DIV)
TIMESCALE (0.5µs/DIV)
FIGURE 11. PFM MODE OPERATION
(VIN = 3.6V, VOUT = 5V, 10mA LOAD)
FIGURE 12. PWM MODE OPERATION
(VIN = 3.6V, VOUT = 5V, 200mA LOAD)
VIN (1V/DIV)
VIN (1V/DIV)
VOUT, 5V OFFSET
(50mV/DIV)
VOUT, 5V OFFSET
(200mV/DIV)
10mA – 1A
LOAD TRANSIENT
(240mA/µs SLEW RATE)
0mA – 50mA
LOAD TRANSIENT
LOAD CURRENT
(20mA/DIV)
INDUCTOR CURRENT
(1A/DIV)
TIMESCALE (200µs/DIV)
TIMESCALE (200µs/DIV)
FIGURE 13. LOAD TRANSIENT (VIN = 3.0V, VOUT = 5V)
FIGURE 14. LOAD TRANSIENT (VIN = 3.0V, VOUT = 5V)
FN8569 Rev 3.00
March 7, 2014
Page 7 of 12
ISL91117
Typical Performance Curves (Continued)
4.2V – 3.6V
LINE TRANSIENT
3.8V – 3.2V
LINE TRANSIENT
VIN (1V/DIV)
VIN (1V/DIV)
VOUT, 5V OFFSET
(200mV/DIV)
VOUT, 5V OFFSET
(100mV/DIV)
TIMESCALE (1ms/DIV)
TIMESCALE (500µs/DIV)
FIGURE 15. LINE TRANSIENT (VOUT = 5V)
FIGURE 16. LINE TRANSIENT (VOUT = 5V)
EN (2V/DIV)
EN (2V/DIV)
VOUT (1V/DIV)
VOUT (1V/DIV)
INDUCTOR CURRENT
(500mA/DIV)
INDUCTOR CURRENT
(500mA/DIV)
TIMESCALE (500µs/DIV)
TIMESCALE (500µs/DIV)
FIGURE 17. START-UP WITH NO LOAD (VIN = 3.6V, VOUT = 5V)
FIGURE 18. START-UP WITH 25 (VIN = 3.6V, VOUT = 5V)
FN8569 Rev 3.00
March 7, 2014
Page 8 of 12
ISL91117
guarantee proper operation. When the VIN voltage falls below the
UVLO threshold, the regulator is disabled.
Functional Description
Functional Overview
Thermal Shutdown
Refer to the “Block Diagram” on page 2. The ISL91117
implements a complete boost switching regulator, with PWM
controller, internal switches, references, protection circuitry, and
control inputs.
A built-in thermal protection feature protects the ISL91117 if the
die temperature reaches +150°C (typical). At this die
temperature, the regulator is completely shut down. The die
temperature continues to be monitored in this thermal-shutdown
mode. When the die temperature falls to +125°C (typical), the
device will resume normal operation.
Internal Supply and References
Referring to the “Block Diagram” on page 2, the ISL91117 provides
two power input pins. The PVIN pin supplies input power to the
DC/DC converter, while the VIN pin provides the operating voltage
When exiting thermal shutdown, the ISL91117 will execute its
soft-start sequence.
source required for stable V
(GND and PGND) are provided to avoid problems caused by ground
shift due to the high switching currents.
generation. Separate ground pins
REF
External Synchronization
An external sync feature is provided. Applying a clock signal with
a frequency between 2.75MHz and 3.25MHz at the MODE input,
forces the ISL91117 to synchronize to this external clock. The
MODE input supports standard logic levels.
Enable Input
A master enable pin EN allows the device to be enabled. Driving
the EN pin LOW invokes a power-down mode, where most
internal device functions, including input and output power-good
detection, are disabled.
PWM Operation
The control scheme of the device is based on the peak current
mode control, and the control loop is compensated internally.
The peak current of the N-channel MOSFET switch is sensed to
limit the maximum current flowing through the switch and the
inductor.
Soft Discharge
When the device is disabled by driving EN LOW, an internal
resistor between VOUT and GND is activated. This internal
resistor has typical 120Ω resistance.
The control circuit includes ramp generator, slope compensator,
error amplifier, PWM comparator (see “Block Diagram” on page 2).
The ramp signal is derived from the inductor current. This ramp
signal is then compared to the error amplifier output to generate
the PWM gating signals for driving both N-channel and P-channel
MOSFETs. The PWM operation is initialized by the clock from the
internal oscillator (typical 2.6MHz). The N-channel MOSFET is
turned ON at the beginning of a PWM cycle, the P-channel MOSFET
remains OFF, and the current starts ramping up. When the sum of
the ramp and the slope compensator output reaches the error
amplifier output voltage, the PWM comparator outputs a signal to
turn OFF the N-channel MOSFET. Here, both MOSFETs remain OFF
during the dead-time interval, and then the P-channel MOSFET is
turned ON and remains ON until the end of this PWM cycle. During
this time, the inductor current ramps down until the next clock. At
this point, following a short dead time, the N-channel MOSFET is
again turned ON, repeating as previously described.
POR Sequence and Soft-start
Bringing the EN pin HIGH allows the device to power-up. A
number of events occur during the start-up sequence. The
internal voltage reference powers up, and stabilizes. The device
then starts operating. There is a typical 1ms delay between
assertion of the EN pin and the start of switching regulator
soft-start ramp.
The soft-start feature minimizes output voltage overshoot and
input in-rush currents. During soft-start, the reference voltage is
ramped up to provide a ramping VOUT voltage. While the output
voltage is lower than approximately 20% of the target output
voltage, switching frequency is reduced to a fraction of the
normal switching frequency to aid in producing low duty cycles
necessary to avoid input in-rush current spikes. Once the output
voltage exceeds that threshold, switching frequency is increased
to its nominal value.
PFM Operation
The soft-start time is typically 3ms. Increasing the load current
will increase these typical soft-start times.
The boost converter enters the PFM mode of operation under light
load conditions. When the inductor current is sensed to cross zero,
the converter enters PFM mode. In this mode, each pulse cycle is
still synchronized by the PWM clock. The N-channel MOSFET is
turned ON at the rising edge of the clock and turned OFF when the
inductor peak current reaches a certain current limit. Then the
P-channel MOSFET is turned ON, and it stays ON until the inductor
current goes to zero. Subsequently, both N-channel and P-channel
MOSFETs are turned OFF until the next clock cycle starts, at which
time the N-channel MOSFET is turned ON again.
Short Circuit Protection
The ISL91117 provides short-circuit protection by monitoring the
feedback voltage. When feedback voltage is sensed to be lower
than a certain threshold, the PWM oscillator frequency is reduced
in order to protect the device from damage. The P-Channel
MOSFET peak current limit remains active during this state.
Undervoltage Lockout
The undervoltage lockout (UVLO) feature prevents abnormal
operation in the event that the supply voltage is too low to
In most operating conditions, there will be multiple PFM pulses
to charge up the output capacitor. In addition to the inductor
current limit for PFM operation, the PFM pulses are also
controlled by output voltage. These pulses continue until VOUT
FN8569 Rev 3.00
March 7, 2014
Page 9 of 12
ISL91117
has achieved the upper threshold of the PFM hysteretic
controller. Switching then stops, and remains stopped until VOUT
decays to the lower threshold of the hysteretic PFM controller.
Non-Adjustable Version FB Pin Connection
The fixed output version of the ISL91117 does not require
external resistors or a capacitor on the FB pin. Simply connect
VOUT to FB, as shown in Figure 20.
Applications Information
L1
1µH
Component Selection
The fixed-output version of the ISL91117 requires only three
external power components to implement the boost converter:
an inductor, an input capacitor, and an output capacitor.
VIN =
BLKG
1.8V TO 4.8V
PVIN
VOUT = 5V
C1
22µF
VOUT
FB
The adjustable ISL91117 versions require three additional
components to program the output voltage. Two external
resistors program the output voltage, and a small capacitor is
added to improve stability and response.
ISL91117
VIN
EN
C2
2x
22µF
MODE
L1
1µH
FIGURE 20. TYPICAL ISL91117II7Z APPLICATION
VIN = 1.8V
TO 4.8V
BLKG
PVIN
VOUT = 5V
C1
22µF
Inductor Selection
VOUT
FB
C3
R1
An inductor with high frequency core material (e.g., ferrite core)
should be used to minimize core losses and provide good
efficiency. The inductor must be able to handle the peak
switching currents without saturating.
ISL91117
VIN
EN
22pF
C2
2x
22µF
320k
MODE
R2
60.4k
A 1µH inductor with ≥4A saturation current rating is
recommended. Select an inductor with low DCR to provide good
efficiency. In applications where radiated noise must be
minimized, a toroidal or shielded inductor can be used.
FIGURE 19. TYPICAL ISL91117IIAZ APPLICATION
TABLE 1. INDUCTOR VENDOR INFORMATION
Output Voltage Programming, Adjustable
Version
Setting and controlling the output voltage of the ISL91117IIAZ
(adjustable output version) can be accomplished by selecting the
external resistor values.
MANUFACTURER
Coilcraft
SERIES
WEBSITE
XFL4020-102ME www.coilcraft.com
LQH5BPN1R0NT0 www.murata.com
Murata
PVIN and VOUT Capacitor Selection
Equation 1 can be used to derive the R1 and R2 resistor values:
The input and output capacitors should be ceramic X5R type with
low ESL and ESR. The recommended input capacitor value is
22µF. The recommended VOUT capacitor value is 2x22µF or
47µF.
R1
R2
-------
V
= 0.8V 1 +
(EQ. 1)
OUT
When designing a PCB, include a GND guard band around the
feedback resistor network to reduce noise and improve accuracy
and stability. Resistors R1 and R2 should be positioned close to
the FB pin.
TABLE 2. CAPACITOR VENDOR INFORMATION
MANUFACTURER
AVX
SERIES
WEBSITE
www.avx.com
X5R
X5R
X5R
X5R
Feed-Forward Capacitor Selection
Murata
Taiyo Yuden
TDK
www.murata.com
www.t-yuden.com
www.tdk.com
A small capacitor (C3 in Figure 19) in parallel with resistor R1 is
required to provide the specified load and line regulation. The
suggested value of this capacitor is 22pF for R1 = 320kΩ. An
NPO type capacitor is recommended.
FN8569 Rev 3.00
March 7, 2014
Page 10 of 12
ISL91117
Recommended PCB Layout
Correct PCB layout is critical for proper operation of the
ISL91117. The input and output capacitors should be positioned
as closely to the IC as possible. The ground connections of the
input and output capacitors should be kept as short as possible,
and should be on the component layer to avoid problems that are
caused by high switching currents flowing through PCB vias.
FIGURE 21. RECOMMENDED LAYOUT
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
FN8569.3
CHANGE
March 7, 2014
Updated Related Literature.
Figure 18 on page 8 Title changed from START-UP WITH NO LOAD (VIN = 3.6V, VOUT = 5V) to START-UP WITH
25 (VIN = 3.6V, VOUT = 5V).
February 4, 2014
FN8569.2
Initial Release.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
© Copyright Intersil Americas LLC 2014. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8569 Rev 3.00
March 7, 2014
Page 11 of 12
ISL91117
Package Outline Drawing
W4x5.20F
20 BALL WAFER LEVEL CHIP SCALE PACKAGE (WLCSP 0.4mm PITCH)
Rev 0, 5/13
1.200
X
1.72±0.030
Y
0.400
5
4
3
20x 0.265±0.035
2.335±0.030
1.600
2
1
0.3675
(4X)
0.10
A
B
C
D
0.260
0.200
PIN 1 (A1 CORNER)
TOP VIEW
BOTTOM VIEW
Z
SEATING PLANE
3
0.05 Z
PACKAGE OUTLINE
0.240
0.040 BSC
(BACKSIDE COATING)
0.400
0.290
0.265±0.035 x20
0.10M Z X Y
Z
0.05M
0.200±0.030
0.540±0.050
RECOMMENDED LAND PATTERN
SIDE VIEW
NOTES:
1.
Dimensions and tolerance per ASME Y 14.5M - 1994.
2. Dimension is measured at the maximum bump diameter
parallel to primary datum Z .
3. Primary datum Z and seating plane are defined by the spherical
crowns of the bump.
4. Bump position designation per JESD 95-1, SPP-010.
5. There shall be a minimum clearance of 0.10mm between
the edge of the bump and the body edge.
FN8569 Rev 3.00
March 7, 2014
Page 12 of 12
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_2.jpg)
ISL91117IIA-EVZ
High Efficiency Synchronous Boost Converter with 4.2A Switches and Output Disconnect
RENESAS
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_2.jpg)
ISL91117IIAZ-T
High Efficiency Synchronous Boost Converter with 4.2A Switches and Output Disconnect
RENESAS
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00327/img/page/ISL91117_2009281_files/ISL91117_2009281_2.jpg)
ISL91117IIAZ-T7A
High Efficiency Synchronous Boost Converter with 4.2A Switches and Output Disconnect
RENESAS
![](http://pdffile.icpdf.com/pdf1/p00176/img/page/ISL91_988231_files/ISL91_988231_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00176/img/page/ISL91_988231_files/ISL91_988231_2.jpg)
ISL9111AEH30Z-T
Low Input Voltage, High Efficiency Synchronous Boost Converter with 1A Switch
INTERSIL
![](http://pdffile.icpdf.com/pdf2/p00326/img/page/ISL9111AH30-_2002814_files/ISL9111AH30-_2002814_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00326/img/page/ISL9111AH30-_2002814_files/ISL9111AH30-_2002814_2.jpg)
ISL9111AEH30Z-T
Low Input Voltage, High Efficiency Synchronous Boost Converter with 1A Switch
RENESAS
![](http://pdffile.icpdf.com/pdf1/p00176/img/page/ISL91_988231_files/ISL91_988231_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00176/img/page/ISL91_988231_files/ISL91_988231_2.jpg)
ISL9111AEH30Z-T7A
Low Input Voltage, High Efficiency Synchronous Boost Converter with 1A Switch
INTERSIL
![](http://pdffile.icpdf.com/pdf2/p00326/img/page/ISL9111AH30-_2002814_files/ISL9111AH30-_2002814_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00326/img/page/ISL9111AH30-_2002814_files/ISL9111AH30-_2002814_2.jpg)
ISL9111AEH30Z-T7A
Low Input Voltage, High Efficiency Synchronous Boost Converter with 1A Switch
RENESAS
©2020 ICPDF网 联系我们和版权申明