M38048FDHFP [RENESAS]
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER; 单片8位CMOS微机型号: | M38048FDHFP |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
文件: | 总116页 (文件大小:1247K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3804 Group (Spec.H)
REJ03B0131-0101Z
Rev.1.01
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Jan 25, 2005
DESCRIPTION
The 3804 group (Spec. H) is the 8-bit microcomputer based on the
ꢀPower source voltage
In high-speed mode
740 family core technology.
At 16.8 MHz oscillation frequency ............................ 4.5 to 5.5 V
At 12.5 MHz oscillation frequency ............................ 4.0 to 5.5 V
At 8.4 MHz oscillation frequency) ............................. 2.7 to 5.5 V
In middle-speed mode
The 3804 group (Spec. H) is designed for household products, of-
fice automation equipment, and controlling systems that require
analog signal processing, including the A/D converter and D/A
converters.
At 16.8 MHz oscillation frequency ............................ 4.5 to 5.5 V
At 12.5 MHz oscillation frequency ............................ 2.7 to 5.5 V
In low-speed mode
FEATURES
ꢀBasic machine-language instructions ...................................... 71
ꢀMinimum instruction execution time ................................ 0.24 µs
(at 16.8 MHz oscillation frequency)
At 32 kHz oscillation frequency................................. 2.7 to 5.5 V
ꢀPower dissipation
In high-speed mode ............................................. 27.5 mW (typ.)
(at 16.8 MHz oscillation frequency, at 5 V power source voltage)
In low-speed mode ............................................... 1200 µW (typ.)
(at 32 kHz oscillation frequency, at 3 V power source voltage)
ꢀOperating temperature range....................................–20 to 85°C
ꢀPackages
ꢀMemory size
Flash memory.............................................................. 60 K bytes
RAM ............................................................................ 2048 bytes
ꢀProgrammable input/output ports ............................................ 56
ꢀSoftware pull-up resistors ................................................. Built-in
ꢀInterrupts
SP .................................................. 64P4B (64-pin 750 mil SDIP)
FP ....................................... 64P6N-A (64-pin 14 ꢀ 14 mm QFP)
HP ..................................... 64P6Q-A (64-pin 10 ꢀ 10 mm LQFP)
KP ..................................... 64P6U-A (64-pin 14 ꢀ 14 mm LQFP)
21 sources, 16 vectors .................................................................
(external 8, internal 12, software 1)
ꢀTimers ........................................................................... 16-bit ꢀ 1
8-bit ꢀ 4
(with 8-bit prescaler)
<Flash memory mode>
ꢀWatchdog timer ............................................................ 16-bit ꢀ 1
ꢀSerial interface
ꢀPower source voltage...................................... Vcc = 2.7 to 5.5 V
ꢀProgram/Erase voltage.................................... Vcc = 2.7 to 5.5 V
ꢀProgramming method ...................... Programming in unit of byte
ꢀErasing method ...................................................... Block erasing
ꢀProgram/Erase control by software command
Serial I/O1, 3 ............... 8-bit ꢀ 2 (UART or Clock-synchronized)
Serial I/O2 ...................................8-bit ꢀ 1 (Clock-synchronized)
ꢀPWM ............................................8-bit ꢀ 1 (with 8-bit prescaler)
2
ꢀMulti-master I C-BUS interface ................................... 1 channel
ꢀNumber of times for programming/erasing ............................ 100
ꢀA/D converter ............................................. 10-bit ꢀ 16 channels
(8-bit reading enabled)
ꢀNotes
ꢀD/A converter.................................................. 8-bit ꢀ 2 channels
ꢀLED direct drive port .................................................................. 8
ꢀClock generating circuit..................................... Built-in 2 circuits
(connect to external ceramic resonator or quartz-crystal oscillator)
Cannot be used for application embedded in the MCU card.
Currently support products are listed below.
Table 1 Support products
Flash memory size
Product name
RAM size (bytes)
2048
Package
Remarks
(bytes)
M38049FFHSP
M38049FFHFP
M38049FFHHP
M38049FFHKP
64P4B
64P6N-A
64P6Q-A
64P6U-A
61440
Vcc = 2.7 to 5.5 V
Rev.1.01 Jan 25, 2005 page 1 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
PIN CONFIGURATION (TOP VIEW)
49
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
P20(LED0)
P21(LED1)
P22(LED2)
P23(LED3)
P24(LED4)
P25(LED5)
P26(LED6)
P37/SRDY3
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
P36/SCLK3
P35/TXD3
P34/RXD3
P33/SCL
P32/SDA
P31/DA2
P30/DA1
VCC
P27(LED7)
VSS
M38049FFHFP/HP/KP
VREF
XOUT
XIN
AVSS
P67/AN7
P66/AN6
P65/AN5
P64/AN4
P63/AN3
P40/INT40/XCOUT
P41/INT00/XCIN
RESET
CNVSS
P42/INT1
Package type : 64P6N-A/64P6Q-A/64P6U-A
Fig. 1 3804 group (Spec. H) pin configuration
PIN CONFIGURATION (TOP VIEW)
1
2
3
4
5
6
7
8
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
V
V
AVSS
/AN
/AN
/AN
CC
P3
P3
0
1
/DA
/DA
1
2
REF
P3
2
/SDA
/SCL
/R
/T
/
/
P6
P6
P6
7
6
5
7
6
5
P3
P3
3
4
XD3
P35
XD
3
P64/AN4
P36
P37
P00
P01
P02
P03
P04
P05
P06
P07
S
S
CLK3
RDY3
P63
P62
P61
P60
/AN
/AN
/AN
/AN
7/INT
/PWM
3
2
1
0
3
9
/AN
/AN
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
/AN10
/AN11
/AN12
/AN13
/AN14
/AN15
/INT41
/INT01
P5
P56
P5
P5
5
/CNTR
/CNTR
1
4
0
P5
P5
P5
P5
CNTR
P4
P4
3
/SRDY2
/SCLK2
/SOUT2
/SIN2
2
P1
P1
P1
P1
P1
P1
P1
P1
P2
P2
P2
P2
P2
P2
P2
P2
0
1
2
3
4
5
6
7
1
0
P4
7
/SRDY1
/
2
6
/SCLK1
5
/T
/R
X
D
D
1
1
2
P4
P4
4
X
3
/INT
/INT
CNVSS
RESET
P42
1
0
(LED
(LED
(LED
(LED
(LED
(LED
(LED
(LED
0
)
)
)
)
)
)
)
)
1
2
3
4
5
6
7
1
2
3
4
5
6
7
P4
1
/INT00/XCIN
/INT40/XCOUT
P4
0
X
IN
OUT
SS
X
V
Package type : 64P4B
Fig. 2 3804 group (Spec. H) pin configuration
Rev.1.01 Jan 25, 2005 page 2 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
FUNCTIONAL BLOCK
Fig. 3 Functional block diagram
Rev.1.01 Jan 25, 2005 page 3 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
PIN DESCRIPTION
Table 2 Pin description
Functions
Pin
Name
Function except a port function
VCC, VSS
CNVSS
•Apply voltage of 2.7 V–5.5 V to Vcc, and 0 V to Vss.
•This pin controls the operation mode of the chip.
•Normally connected to VSS.
Power source
CNVSS input
VREF
AVSS
•Reference voltage input pin for A/D and D/A converters.
•Analog power source input pin for A/D and D/A converters.
•Connect to VSS.
Reference voltage
Analog power source
•Reset input pin for active “L”.
RESET
XIN
Reset input
Clock input
•Input and output pins for the clock generating circuit.
•Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set
the oscillation frequency.
XOUT
Clock output
•When an external clock is used, connect the clock source to the XIN pin and leave the XOUT
pin open.
•8-bit CMOS I/O port.
•A/D converter input pin
•Interrupt input pin
P00/AN8–
P07/AN15
I/O port P0
I/O port P1
•I/O direction register allows each pin to be individually
programmed as either input or output.
P10/INT41
P11/INT01
•CMOS compatible input level.
•CMOS 3-state output structure.
•Pull-up control is enabled in a bit unit.
P12–P17
P20–P27
I/O port P2
I/O port P3
•P20–P27 are enabled to output large current for LED drive.
P3
P3
0
1
/DA
/DA
1
2
•8-bit CMOS I/O port.
•D/A converter input pin
•I/O direction register allows each pin to be individually
programmed as either input or output.
2
P32/SDA
P33/SCL
•I C-BUS interface function pins
•CMOS compatible input level.
P34/RxD3
P35/TxD3
P36/SCLK3
P37/SRDY3
•P32 to P33 can be switched between CMOS compat-
ible input level or SMBUS input level in the I C-BUS
interface function.
•Serial I/O3 function pin
2
•P30, P31, P34–P37 are CMOS 3-state output structure.
•P32, P33 are N-channel open-drain output structure.
•Pull-up control of P30, P31, P34–P37 is enabled in a bit
unit.
•8-bit CMOS I/O port.
•Interrupt input pin
P40/INT40/
XCOUT
P41/INT00/
XCIN
I/O port P4
•I/O direction register allows each pin to be individually
programmed as either input or output.
•Sub-clock generating I/O pin
(resonator connected)
•Interrupt input pin
•CMOS compatible input level.
P42/INT1
P43/INT2
•CMOS 3-state output structure.
•Pull-up control is enabled in a bit unit.
P44/RxD1
P45/TxD1
P46/SCLK1
•Serial I/O1 function pin
P47/SRDY1
/CNTR2
•Serial I/O1, timer Z function pin
•Serial I/O2 function pin
P50/SIN2
I/O port P5
•8-bit CMOS I/O port.
P51/SOUT2
P52/SCLK2
P53/SRDY2
•I/O direction register allows each pin to be individually
programmed as either input or output.
•CMOS compatible input level.
P54/CNTR0
P55/CNTR1
P56/PWM
P57/INT3
•Timer X function pin
•Timer Y function pin
•PWM output pin
•CMOS 3-state output structure.
•Pull-up control is enabled in a bit unit.
•Interrupt input pin
I/O port P6
•A/D converter input pin
P60/AN0–
P67/AN7
Rev.1.01 Jan 25, 2005 page 4 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
PART NUMBERING
Product name
M3804 9
F
F
H
SP
Package type
SP : 64P4B
FP : 64P6N-A
HP : 64P6Q-A
KP : 64P6U-A
: standard
H : Minner spec. change product
ROM/PROM size
: 4096 bytes
: 8192 bytes
: 12288 bytes
: 16384 bytes
: 20480 bytes
: 24576 bytes
: 28672 bytes
: 32768 bytes
9: 36864 bytes
A: 40960 bytes
B: 45056 bytes
C: 49152 bytes
D: 53248 bytes
E: 57344 bytes
F: 61440 bytes
1
2
3
4
5
6
7
8
Memory type
F : Flash memory version
RAM size
0: 192 bytes
1: 256 bytes
2: 384 bytes
3: 512 bytes
4: 640 bytes
5 : 768 bytes
6 : 896 bytes
7 : 1024 bytes
8 : 1536 bytes
9 : 2048 bytes
Fig. 4 Part numbering
Rev.1.01 Jan 25, 2005 page 5 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
GROUP EXPANSION
Packages
64P4B ......................................... 64-pin shrink plastic-molded DIP
64P6N-A .................................... 0.8 mm-pitch plastic molded QFP
64P6Q-A .................................. 0.5 mm-pitch plastic molded LQFP
64P6U-A .................................. 0.8 mm-pitch plastic molded LQFP
Renesas plans to expand the 3804 group (Spec. H) as follows.
Memory Size
Flash memory size ......................................................... 60 K bytes
RAM size ....................................................................... 2048 bytes
Memory Expansion Plan
As of Jan. 2005
ROM size (bytes)
:
Under development
: Mass production
M38049FFH
M38049FF
60K
48K
32K
28K
24K
20K
16K
12K
8K
384
512
640
768
896
1024
1152
1280
1408
1536
2048
3072
4032
RAM size (bytes)
Fig. 5 Memory expansion plan
Rev.1.01 Jan 25, 2005 page 6 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
FUNCTIONAL DESCRIPTION
[Stack Pointer (S)]
CENTRAL PROCESSING UNIT (CPU)
The 3804 group (Spec. H) uses the standard 740 Family instruc-
tion set. Refer to the table of 740 Family addressing modes and
machine instructions or the 740 Family Software Manual for de-
tails on the instruction set.
The stack pointer is an 8-bit register used during subroutine calls
and interrupts. This register indicates start address of stored area
(stack) for storing registers during subroutine calls and interrupts.
The low-order 8 bits of the stack address are determined by the
contents of the stack pointer. The high-order 8 bits of the stack ad-
dress are determined by the stack page selection bit. If the stack
page selection bit is “0” , the high-order 8 bits becomes “0016”. If
the stack page selection bit is “1”, the high-order 8 bits becomes
“0116”.
Machine-resident 740 Family instructions are as follows:
The FST and SLW instructions cannot be used.
The STP, WIT, MUL, and DIV instructions can be used.
[Accumulator (A)]
The operations of pushing register contents onto the stack and
popping them from the stack are shown in Figure 7.
Store registers other than those described in Figure 6 with pro-
gram when the user needs them during interrupts or subroutine
calls (see Table 3).
The accumulator is an 8-bit register. Data operations such as data
transfer, etc. are executed mainly through the accumulator.
[Index Register X (X)]
The index register X is an 8-bit register. In the index addressing
modes, the value of the OPERAND is added to the contents of
register X and specifies the real address.
[Program Counter (PC)]
The program counter is a 16-bit counter consisting of two 8-bit
registers PCH and PCL. It is used to indicate the address of the
next instruction to be executed.
[Index Register Y (Y)]
The index register Y is an 8-bit register. In partial instruction, the
value of the OPERAND is added to the contents of register Y and
specifies the real address.
b0
b7
A
Accumulator
b0
b0
b0
b0
b0
b7
X
Index register X
Index register Y
b7
Y
b7
S
Stack pointer
b15
b7
b7
PCH
PC
L
Program counter
N V T B D I Z C
Processor status register (PS)
Carry flag
Zero flag
Interrupt disable flag
Decimal mode flag
Break flag
Index X mode flag
Overflow flag
Negative flag
Fig. 6 740 Family CPU register structure
Rev.1.01 Jan 25, 2005 page 7 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
On-going Routine
Execute JSR
Interrupt request
(Note)
M (S) (PCH)
(S) (S) – 1
M (S) (PCL)
(S) (S) – 1
M (S) (PS)
(S) (S) – 1
Push return address
on stack
M (S) (PCH)
(S) (S) – 1
M (S) (PCL)
(S) (S)– 1
Subroutine
Push return address
on stack
Push contents of processor
status register on stack
Interrupt
Service Routine
I Flag is set from “0” to “1”
Execute RTS
(S) (S) + 1
Fetch the jump vector
Execute RTI
(S) (S) + 1
POP return
address from stack
POP contents of
processor status
register from stack
(PCL) M (S)
(S) (S) + 1
(PCH) M (S)
(PS)
M (S)
(S) (S) + 1
(PCL) M (S)
(S) (S) + 1
(PCH) M (S)
POP return
address
from stack
Note: Condition for acceptance of an interrupt
Interrupt enable flag is “1”
Interrupt disable flag is “0”
Fig. 7 Register push and pop at interrupt generation and subroutine call
Table 3 Push and pop instructions of accumulator or processor status register
Push instruction to stack
Pop instruction from stack
Accumulator
PHA
PHP
PLA
PLP
Processor status register
Rev.1.01 Jan 25, 2005 page 8 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
•Bit 4: Break flag (B)
[Processor status register (PS)]
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
The processor status register is an 8-bit register consisting of 5
flags which indicate the status of the processor after an arithmetic
operation and 3 flags which decide MCU operation. Branch opera-
tions can be performed by testing the Carry (C) flag , Zero (Z) flag,
Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z,
V, N flags are not valid.
•Bit 5: Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed
between accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
•Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
•Bit 1: Zero flag (Z)
•Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
•Bit 7: Negative flag (N)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
•Bit 2: Interrupt disable flag (I)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is “1”.
•Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
and SBC instructions can execute decimal arithmetic.
Table 4 Set and clear instructions of each bit of processor status register
N flag
C flag
SEC
CLC
Z flag
I flag
SEI
D flag
SED
CLD
B flag
T flag
SET
CLT
V flag
–
–
–
–
–
–
–
Set instruction
CLI
CLV
Clear instruction
Rev.1.01 Jan 25, 2005 page 9 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
[CPU Mode Register (CPUM)] 003B16
The CPU mode register contains the stack page selection bit, etc.
The CPU mode register is allocated at address 003B16.
b7
b0
CPU mode register
1
(
CPUM : address 003B16)
Processor mode bits
b1 b0
0
0
1
1
0 : Single-chip mode
1 :
0 : Not available
1 :
Stack page selection bit
0 : 0 page
1 : 1 page
Fix this bit to “1”.
Port XC switch bit
0 : I/O port function (stop oscillating)
1 : XCIN–XCOUT oscillating function
Main clock (XIN–XOUT) stop bit
0 : Oscillating
1 : Stopped
Main clock division ratio selection bits
b7 b6
0
0
1
1
0 : φ = f(XIN)/2 (high-speed mode)
1 : φ = f(XIN)/8 (middle-speed mode)
0 : φ = f(XCIN)/2 (low-speed mode)
1 : Not available
Fig. 8 Structure of CPU mode register
Rev.1.01 Jan 25, 2005 page 10 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
MISRG
ꢀMiddle-speed mode automatic switch by SCL/SDA Interrupt
The SCL/SDA interrupt source enables an automatic switch when
the middle-speed mode automatic switch set bit (bit 1) of MISRG
(address 001016) is set to “1”. The conditions for an automatic
(1) Bit 0 of address 001016: Oscillation stabilizing time set af-
ter STP instruction released bit
When the MCU stops the clock oscillation by the STP instruction
and the STP instruction has been released by an external interrupt
source, usually, the fixed values of Timer 1 and Prescaler 12
(Timer 1 = 0116, Prescaler 12 = FF16) are automatically reloaded
in order for the oscillation to stabilize. The user can inhibit the au-
tomatic setting by setting “1” to bit 0 of MISRG (address 001016).
However, by setting this bit to “1”, the previous values, set just be-
fore the STP instruction was executed, will remain in Timer 1 and
Prescaler 12. Therefore, you will need to set an appropriate value
to each register, in accordance with the oscillation stabilizing time,
before executing the STP instruction.
2
switch execution depend on the settings of bits 5 and 6 of the I C
START/STOP condition control register (address 001616). Bit 5 is
the SCL/SDA interrupt pin polarity selection bit and bit 6 is the
SCL/SDA interrupt pin selection bit. The main clock oscillation sta-
bilizing time can also be selected by middle-speed mode
automatic switch wait time set bit (bit 2) of the MISRG.
ꢀMiddle-speed mode automatic switch by program
The middle-speed mode can also be automatically switched by
program while operating in low-speed mode. By setting the
middle-speed automatic switch start bit (bit 3) of MISRG (address
001016) to “1” in the condition that the middle-speed mode auto-
matic switch set bit is “1” while operating in low-speed mode, the
MCU will automatically switch to middle-speed mode. In this case,
the oscillation stabilizing time of the main clock can be selected by
the middle-speed automatic switch wait time set bit (bit 2) of
MISRG (address 001016).
Figure 9 shows the structure of MISRG.
(2) Bits 1, 2, 3 of address 001016: Middle-speed Mode Auto-
matic Switch Function
In order to switch the clock mode of an MCU which has a sub-
clock, the following procedure is necessary:
set CPU mode register (003B16) --> start main clock oscillation -->
wait for oscillation stabilization --> switch to middle-speed mode
(or high-speed mode).
However, the 3804 group (Spec. H) has the built-in function which
automatically switches from low to middle-speed mode either by
the SCL/SDA interrupt or by program.
b7
b0
MISRG
(MISRG : address 001016
)
Oscillation stabilizing time set after STP instruction
released bit
0: Automatically set “0116” to Timer 1, “FF16” to
Prescaler 12
1: Automatically set disabled
Middle-speed mode automatic switch set bit
0: Not set automatically
1: Automatic switching enabled (Note1, 2)
Middle-speed mode automatic switch wait time set bit
0: 4.5 to 5.5 machine cycles
1: 6.5 to 7.5 machine cycles
Middle-speed mode automatic switch start bit
(Depending on program)
0: Invalid
1: Automatic switch start (Note1)
Not used (return “0” when read)
(Do not write “1” to this bit)
Note 1: During operation in low-speed mode, it is possible automatically to
switch to middle-speed mode owing to SCL/SDA interrupt.
2: When automatic switch to middle-speed mode from low-speed
mode occurs, the values of CPU mode register (003B16) change.
Fig. 9 Structure of MISRG
Rev.1.01 Jan 25, 2005 page 11 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
MEMORY
Interrupt Vector Area
Special Function Register (SFR) Area
The Special Function Register area in the zero page contains con-
trol registers such as I/O ports and timers.
The interrupt vector area contains reset and interrupt vectors.
Zero Page
Access to this area with only 2 bytes is possible in the zero page
RAM
addressing mode.
The RAM is used for data storage and for stack area of subroutine
calls and interrupts.
Special Page
Access to this area with only 2 bytes is possible in the special
ROM
page addressing mode.
The ROM area can program/erase.
RAM area
RAM size
(bytes)
Address
XXXX16
000016
SFR area
192
256
384
512
640
768
896
1024
1536
2048
00FF16
013F16
01BF16
023F16
02BF16
033F16
03BF16
043F16
063F16
083F16
Zero page
004016
010016
RAM
XXXX16
Not used
0FF016
SFR area
0FFF16
Not used
YYYY16
ROM area
ROM size
(bytes)
Address
YYYY16
4096
8192
F00016
E00016
D00016
C00016
B00016
A00016
900016
800016
700016
600016
500016
400016
300016
200016
100016
12288
16384
20480
24576
28672
32768
36864
40960
45056
49152
53248
57344
61440
ROM
FF0016
FFDC16
Special page
Interrupt vector area
FFFE16
FFFF16
Fig. 10 Memory map diagram
Rev.1.01 Jan 25, 2005 page 12 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Port P0 (P0)
000016
Prescaler 12 (PRE12)
Timer 1 (T1)
002016
002116
002216
Port P0 direction register (P0D)
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
Port P1 (P1)
Timer 2 (T2)
Port P1 direction register (P1D)
Port P2 (P2)
002316 Timer XY mode register (TM)
Prescaler X (PREX)
Timer X (TX)
002416
002516
002616
Port P2 direction register (P2D)
Port P3 (P3)
Prescaler Y (PREY)
Port P3 direction register (P3D)
Port P4 (P4)
002716 Timer Y (TY)
Timer Z low-order (TZL)
Timer Z high-order (TZH)
002816
002916
Port P4 direction register (P4D)
Port P5 (P5)
002A16 Timer Z mode register (TZM)
Port P5 direction register (P5D)
Port P6 (P6)
002B16
002C16
PWM control register (PWMCON)
PWM prescaler (PREPWM)
Port P6 direction register (P6D)
Timer 12, X count source selection register (T12XCSS)
Timer Y, Z count source selection register (TYZCSS)
002D16 PWM register (PWM)
002E16
002F16
003016
003116
003216
Baud rate generator 3 (BRG3)
Transmit/Receive buffer register 3 (TB3/RB3)
001016 MISRG
2
001116
I C data shift register (S0)
2
Serial I/O3 status register (SIO3STS)
Serial I/O3 control register (SIO3CON)
001216 I C special mode status register (S3)
2
001316
001416
001516
001616
001716
003316 UART3 control register (UART3CON)
I C status register (S1)
2
AD/DA control register (ADCON)
AD conversion register 1 (AD1)
003416
003516
I C control register (S1D)
2
I C clock control register (S2)
2
003616 DA1 conversion register (DA1)
I C START/STOP condition control register (S2D)
2
DA2 conversion register (DA2)
AD conversion register 2 (AD2)
003716
003816
I C special mode control register (S3D)
001816 Transmit/Receive buffer register 1 (TB1/RB1)
001916 Serial I/O1 status register (SIO1STS)
003916 Interrupt source selection register (INTSEL)
003A16 Interrupt edge selection register (INTEDGE)
Serial I/O1 control register (SIO1CON)
UART1 control register (UART1CON)
001A16
001B16
CPU mode register (CPUM)
003B16
003C16
003D16
Interrupt request register 1 (IREQ1)
Interrupt request register 2 (IREQ2)
001C16 Baud rate generator 1 (BRG1)
001D16 Serial I/O2 control register (SIO2CON)
001E16 Watchdog timer control register (WDTCON)
003E16 Interrupt control register 1 (ICON1)
003F16 Interrupt control register 2 (ICON2)
001F16
Serial I/O2 register (SIO2)
Flash memory control register 0 (FMCR0)
Flash memory control register 1 (FMCR1)
Flash memory control register 2 (FMCR2)
Port P0 pull-up control register (PULL0)
Port P1 pull-up control register (PULL1)
Port P2 pull-up control register (PULL2)
Port P3 pull-up control register (PULL3)
Port P4 pull-up control register (PULL4)
Port P5 pull-up control register (PULL5)
Port P6 pull-up control register (PULL6)
0FE016
0FE116
0FE216
0FF016
0FF116
0FF216
0FF316
0FF416
0FF516
0FF616
0FF716
0FF816
0FF916
0FE316 Reserved ꢀ
0FE416
0FE516 Reserved ꢀ
0FE616
Reserved ꢀ
Reserved ꢀ
2
0FE716 Reserved ꢀ
0FE816 Reserved ꢀ
0FE916 Reserved ꢀ
0FEA16 Reserved ꢀ
I C slave address register 0 (S0D0)
2
I C slave address register 1 (S0D1)
2
I C slave address register 2 (S0D2)
Reserved ꢀ
0FEC16 Reserved ꢀ
Reserved ꢀ
ꢀ Reserved area: Do not write any data to these addresses,
0FEB16
because these areas are reserved.
0FED16
0FEE16 Reserved ꢀ
0FEF16 Reserved ꢀ
Fig. 11 Memory map of special function register (SFR)
Rev.1.01 Jan 25, 2005 page 13 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
I/O PORTS
comes an input pin. When “1” is written to that bit, that pin be-
comes an output pin.
The I/O ports have direction registers which determine the input/
output direction of each individual pin. Each bit in a direction reg-
ister corresponds to one pin, and each pin can be set to be input
port or output port.
If data is read from a pin which is set to output, the value of the
port output latch is read, not the value of the pin itself. Pins set to
input are floating. If a pin set to input is written to, only the port
output latch is written to and the pin remains floating.
When “0” is written to the bit corresponding to a pin, that pin be-
Table 5 I/O port function
Related SFRs
Ref.No.
(1)
Name
I/O Structure
CMOS compatible input level
CMOS 3-state output
Non-Port Function
A/D converter input
External interrupt input
Pin
P00/AN8–P07/AN15
P10/INT41
AD/DA control register
Port P0
Port P1
Interrupt edge selection
register
(2)
P11/INT01
P12–P17
(3)
Port P2
Port P3
P20/LED0–
P27/LED7
CMOS compatible input level
CMOS 3-state output
D/A converter output
AD/DA control register
(4)
(5)
P30/DA1
P31/DA2
P32/SDA
P33/SCL
2
2
CMOS compatible input level
N-channel open-drain output
CMOS/SMBUS input level (when
I C-BUS interface func-
I C control register
tion I/O
2
selecting I C-BUS interface function)
CMOS compatible input level
CMOS 3-state output
P34/RxD3
Serial I/O3 function I/O
Serial I/O3 control
register
(6)
(7)
P35/TxD3
UART3 control register
P36/SCLK3
(8)
P37/SRDY3
(9)
P40/INT40/XCIN
P41/INT00/XCOUT
Interrupt edge selection
register
(10)
(11)
CMOS compatible input level
CMOS 3-state output
External interrupt input
Port P4
Sub-clock generating
circuit
CPU mode register
P42/INT1
Interrupt edge selection
register
(2)
External interrupt input
P43/INT2
(6)
(7)
P44/RxD1
Serial I/O1 control
register
Serial I/O1 function I/O
P45/TxD1
UART1 control register
(8)
P46/SCLK1
P47/SRDY1/CNTR2
(12)
Serial I/O1 function I/O
Timer Z function I/O
Serial I/O1 control
register
Timer Z mode register
Serial I/O2 control
register
P50/SIN2
Port P5
Serial I/O2 function I/O
(13)
(14)
(15)
(16)
(17)
CMOS compatible input level
CMOS 3-state output
P51/SOUT2
P52/SCLK2
P53/SRDY2
P54/CNTR0
P55/CNTR1
P56/PWM
P57/INT3
Timer X, Y function I/O
Timer XY mode register
PWM control register
PWM output
(18)
(2)
External interrupt input
Interrupt edge selection
register
P60/AN0–P67/AN7
Port P6
CMOS compatible input level
CMOS 3-state output
A/D converter input
AD/DA control register
(1)
Notes 1: Refer to the applicable sections how to use double-function ports as function I/O ports.
2: Make sure that the input level at each pin is either 0 V or VCC during execution of the STP instruction.
When an input level is at an intermediate potential, a current will flow from VCC to VSS through the input-stage gate.
Rev.1.01 Jan 25, 2005 page 14 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(1) Ports P0, P6
(2) Ports P10, P11, P42, P43, P57
Pull-up control bit
Pull-up control bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
A/D converter input
Analog input pin
selection bit
Interrupt input
(3) Ports P1
2
to P1
7
, P2
(4) Ports P30, P31
Pull-up control bit
Pull-up control bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
D/A converter output
DA
DA
1
2
output enable (P3
0
)
)
output enable (P3
1
(6) Ports P34, P44
(5) Ports P32, P33
Pull-up control bit
2
I C-BUS interface enable bit
Serial I/O enable bit
Receive enable bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
SDA output
SCL output
SDA input
SCL input
Serial I/O input
(7) Ports P3
5
, P4
5
(8) Ports P36, P46
Pull-up control bit
Serial I/O synchronous clock
selection bit
Pull-up control bit
Serial I/O enable bit
P-channel output
disable bit
Serial I/O mode selection bit
Serial I/O enable bit
Serial I/O enable bit
Transmit enable bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Serial I/O clock output
Serial I/O output
Serial I/O external clock input
Fig. 12 Port block diagram (1)
Rev.1.01 Jan 25, 2005 page 15 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(9) Port P3
7
(10) Port P40
Pull-up control bit
Pull-up control bit
Serial I/O3 mode
selection bit
Serial I/O3 enable bit
Port X
C
switch bit
S
RDY3 output enable bit
Direction
register
Direction
register
Data bus
Port latch
Port latch
Data bus
INT40 interrupt input
Serial I/O3 ready output
Oscillator
Port P4
1
Port XC switch bit
(11) Port P4
1
(12) Port P47
Timer Z operating
mode bits
Bit 2
Pull-up control bit
Pull-up control bit
Bit 1
Bit 0
Port X
C
switch bit
Serial I/O1 mode selection bit
Serial I/O1 enable bit
Direction
register
SRDY1 output enable bit
Direction
register
Data bus
Port latch
Data bus
Port latch
INT00 interrupt input
Sub-clock generating circuit input
Timer output
Serial I/O1 ready output
CNTR2 interrupt input
(13) Port P5
0
(14) Port P51
Pull-up control bit
Pull-up control bit
Serial I/O2 transmit completion signal
Serial I/O2 port selection bit
P-channel output
disable bit
Direction
register
Direction
register
Port latch
Data bus
Data bus
Port latch
Serial I/O2 input
Serial I/O2 output
Fig. 13 Port block diagram (2)
Rev.1.01 Jan 25, 2005 page 16 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(15) Port P5
2
(16) Port P53
Pull-up control bit
Pull-up control bit
Serial I/O2 synchronous clock
selection bit
Serial I/O2 port selection bit
S
RDY2 enable bit
Direction
register
Direction
register
Port latch
Data bus
Data bus
Port latch
Serial I/O2 ready output
Serial I/O2 clock output
Serial I/O2 external clock input
(17) Ports P5
4
, P5
5
(18) Port P5
6
Pull-up control bit
Pull-up control bit
PWM output enable bit
Direction
register
Direction
register
Data bus
Port latch
Data bus
Port latch
Pulse output mode
Timer output
PWM output
CNTR interrupt input
Fig. 14 Port block diagram (3)
Rev.1.01 Jan 25, 2005 page 17 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Port P0 pull-up control register
(PULL0: address 0FF016)
P00 pull-up control bit
0: No pull-up
1: Pull-up
P01 pull-up control bit
0: No pull-up
1: Pull-up
P02 pull-up control bit
0: No pull-up
1: Pull-up
P03 pull-up control bit
0: No pull-up
1: Pull-up
P04 pull-up control bit
0: No pull-up
1: Pull-up
P05 pull-up control bit
0: No pull-up
1: Pull-up
P06 pull-up control bit
0: No pull-up
1: Pull-up
P07 pull-up control bit
0: No pull-up
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
1: Pull-up
b7
b0
Port P1 pull-up control register
(PULL1: address 0FF116)
P10 pull-up control bit
0: No pull-up
1: Pull-up
P11 pull-up control bit
0: No pull-up
1: Pull-up
P12 pull-up control bit
0: No pull-up
1: Pull-up
P13 pull-up control bit
0: No pull-up
1: Pull-up
P14 pull-up control bit
0: No pull-up
1: Pull-up
P15 pull-up control bit
0: No pull-up
1: Pull-up
P16 pull-up control bit
0: No pull-up
1: Pull-up
P17 pull-up control bit
0: No pull-up
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
1: Pull-up
Fig. 15 Structure of port pull-up control register (1)
Rev.1.01 Jan 25, 2005 page 18 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Port P2 pull-up control register
(PULL2: address 0FF216
)
P20 pull-up control bit
0: No pull-up
1: Pull-up
P21 pull-up control bit
0: No pull-up
1: Pull-up
P22 pull-up control bit
0: No pull-up
1: Pull-up
P23 pull-up control bit
0: No pull-up
1: Pull-up
P24 pull-up control bit
0: No pull-up
1: Pull-up
P25 pull-up control bit
0: No pull-up
1: Pull-up
P26 pull-up control bit
0: No pull-up
1: Pull-up
P27 pull-up control bit
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
0: No pull-up
1: Pull-up
b7
b0
Port P3 pull-up control register
(PULL3: address 0FF316
)
P30 pull-up control bit
0: No pull-up
1: Pull-up
P31 pull-up control bit
0: No pull-up
1: Pull-up
Not used
(return “0” when read)
P34 pull-up control bit
0: No pull-up
1: Pull-up
P35 pull-up control bit
0: No pull-up
1: Pull-up
P36 pull-up control bit
0: No pull-up
1: Pull-up
P37 pull-up control bit
0: No pull-up
1: Pull-up
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
Fig. 16 Structure of port pull-up control register (2)
Rev.1.01 Jan 25, 2005 page 19 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Port P4 pull-up control register
(PULL4: address 0FF416
)
P40 pull-up control bit
0: No pull-up
1: Pull-up
P41 pull-up control bit
0: No pull-up
1: Pull-up
P42 pull-up control bit
0: No pull-up
1: Pull-up
P43 pull-up control bit
0: No pull-up
1: Pull-up
P44 pull-up control bit
0: No pull-up
1: Pull-up
P45 pull-up control bit
0: No pull-up
1: Pull-up
P46 pull-up control bit
0: No pull-up
1: Pull-up
P47 pull-up control bit
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
0: No pull-up
1: Pull-up
b7
b0
Port P5 pull-up control register
(PULL5: address 0FF516
)
P50 pull-up control bit
0: No pull-up
1: Pull-up
P51 pull-up control bit
0: No pull-up
1: Pull-up
P52 pull-up control bit
0: No pull-up
1: Pull-up
P53 pull-up control bit
0: No pull-up
1: Pull-up
P54 pull-up control bit
0: No pull-up
1: Pull-up
P55 pull-up control bit
0: No pull-up
1: Pull-up
P56 pull-up control bit
0: No pull-up
1: Pull-up
P57 pull-up control bit
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
0: No pull-up
1: Pull-up
Fig. 17 Structure of port pull-up control register (3)
Rev.1.01 Jan 25, 2005 page 20 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Port P6 pull-up control register
(PULL6: address 0FF616
)
P60 pull-up control bit
0: No pull-up
1: Pull-up
P61 pull-up control bit
0: No pull-up
1: Pull-up
P62 pull-up control bit
0: No pull-up
1: Pull-up
P63 pull-up control bit
0: No pull-up
1: Pull-up
P64 pull-up control bit
0: No pull-up
1: Pull-up
P65 pull-up control bit
0: No pull-up
1: Pull-up
P66 pull-up control bit
0: No pull-up
1: Pull-up
P67 pull-up control bit
Note: Pull-up control is valid when the corresponding bit
of the port direction register is “0” (input).
When that bit is “1” (output), pull-up cannot be set
to the port of which pull-up is selected.
0: No pull-up
1: Pull-up
Fig. 18 Structure of port pull-up control register (4)
Rev.1.01 Jan 25, 2005 page 21 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
INTERRUPTS
ꢀ Notes
The 3804 group (Spaec. H)’s interrupts are a type of vector and
occur by 16 sources among 23 sources: nine external, thirteen in-
ternal, and one software.
When setting the followings, the interrupt request bit may be set to
“1”.
•When setting external interrupt active edge
Related register: Interrupt edge selection register (address 003A16)
Timer XY mode register (address 002316)
Timer Z mode register (address 002A16)
I2C START/STOP condition control register
(address 001616)
Interrupt Control
Each interrupt is controlled by an interrupt request bit, an interrupt
enable bit, and the interrupt disable flag except for the software in-
terrupt set by the BRK instruction. An interrupt occurs if the
corresponding interrupt request and enable bits are “1” and the in-
terrupt disable flag is “0”.
•When switching interrupt sources of an interrupt vector address
where two or more interrupt sources are allocated
Related register: Interrupt source selection register
(address 003916)
Interrupt enable bits can be set or cleared by software.
Interrupt request bits can be cleared by software, but cannot be
set by software.
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
ꢀSet the corresponding interrupt enable bit to “0” (disabled).
ꢀSet the interrupt edge select bit or the interrupt source select bit
to “1”.
The reset and the BRK instruction cannot be disabled with any
flag or bit. The I (interrupt disable) flag disables all interrupts ex-
cept the reset and the BRK instruction interrupt.
When several interrupt requests occur at the same time, the inter-
rupts are received according to priority.
ꢀSet the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Interrupt Operation
By acceptance of an interrupt, the following operations are auto-
ꢀSet the corresponding interrupt enable bit to “1” (enabled).
matically performed:
1. The contents of the program counter and the processor status
register are automatically pushed onto the stack.
2. The interrupt disable flag is set and the corresponding interrupt
request bit is cleared.
3. The interrupt jump destination address is read from the vector
table into the program counter.
Interrupt Source Selection
Which of each combination of the following interrupt sources can
be selected by the interrupt source selection register (address
003916).
1. INT0 or Timer Z
2. Serial I/O1 transmission or SCL, SDA
3. CNTR0 or SCL, SDA
4. CNTR1 or Serial I/O3 reception
5. Serial I/O2 or Timer Z
6. INT2 or I2C
7. INT4 or CNTR2
8. A/D converter or serial I/O3 transmission
External Interrupt Pin Selection
The occurrence sources of the external interrupt INT0 and INT4
can be selected from either input from INT00 and INT40 pin, or in-
put from INT01 and INT41 pin by the INT0, INT4 interrupt switch bit
of interrupt edge selection register (bit 6 of address 003A16).
Rev.1.01 Jan 25, 2005 page 22 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 6 Interrupt vector addresses and priority
Vector Addresses (Note 1)
Interrupt Request
Generating Conditions
Remarks
Non-maskable
Interrupt Source
Priority
High
Low
1
2
FFFD16
FFFB16
FFFC16
FFFA16
Reset (Note 2)
INT0
At reset
At detection of either rising or
falling edge of INT0 input
External interrupt
(active edge selectable)
Timer Z
INT1
At timer Z underflow
FFF916
FFF716
FFF516
FFF816
FFF616
FFF416
3
4
5
External interrupt
(active edge selectable)
At detection of either rising or
falling edge of INT1 input
Serial I/O1
reception
Valid when serial I/O1 is selected
At completion of serial I/O1 data
reception
Serial I/O1
transmission
Valid when serial I/O1 is selected
At completion of serial I/O1
transmission shift or when
transmission buffer is empty
At detection of either rising or
falling edge of SCL or SDA
SCL, SDA
External interrupt
(active edge selectable)
At timer X underflow
At timer Y underflow
At timer 1 underflow
At timer 2 underflow
Timer X
Timer Y
Timer 1
Timer 2
CNTR0
6
7
FFF316
FFF116
FFEF16
FFED16
FFEB16
FFF216
FFF016
FFEE16
FFEC16
FFEA16
8
STP release timer underflow
9
At detection of either rising or
falling edge of CNTR0 input
10
External interrupt
(active edge selectable)
SCL, SDA
CNTR1
At detection of either rising or
falling edge of SCL or SDA
External interrupt
(active edge selectable)
At detection of either rising or
falling edge of CNTR1 input
11
FFE816
External interrupt
(active edge selectable)
FFE916
Serial I/O3
reception
At completion of serial I/O3 data
reception
Valid when serial I/O3 is selected
12
13
Serial I/O2
FFE716
FFE516
FFE616
FFE416
At completion of serial I/O2 data
transmission or reception
Valid when serial I/O2 is selected
Timer Z
INT2
At timer Z underflow
At detection of either rising or External interrupt
falling edge of INT2 input
(active edge selectable)
2
At completion of data transfer
I C
At detection of either rising or External interrupt
INT3
14
15
FFE316
FFE116
FFE216
FFE016
falling edge of INT3 input
(active edge selectable)
At detection of either rising or External interrupt
INT4
falling edge of INT4 input
(active edge selectable)
External interrupt
(active edge selectable)
At detection of either rising or
falling edge of CNTR2 input
CNTR2
A/D converter
At completion of A/D conversion
16
17
FFDF16
FFDD16
FFDE16
FFDC16
Valid when serial I/O3 is selected
Non-maskable software interrupt
At completion of serial I/O3
transmission shift or when
transmission buffer is empty
Serial I/O3
transmission
At BRK instruction execution
BRK instruction
Notes 1: Vector addresses contain interrupt jump destination addresses.
2: Reset function in the same way as an interrupt with the highest priority.
Rev.1.01 Jan 25, 2005 page 23 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Interrupt request bit
Interrupt enable bit
Interrupt disable flag (I)
BRK instruction
Reset
Interrupt request
Fig. 19 Interrupt control
Rev.1.01 Jan 25, 2005 page 24 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Interrupt edge selection register
(INTEDGE : address 003A16)
0 : Falling edge active
1 : Rising edge active
INT0 active edge selection bit
INT1 active edge selection bit
Not used (returns “0” when read)
INT2 active edge selection bit
INT3 active edge selection bit
INT4 active edge selection bit
INT0, INT4 interrupt switch bit
0 : INT00, INT40 interrupt
0 : Falling edge active
1 : Rising edge active
1 : INT01, INT41 interrupt
Not used (returns “0” when read)
b7
b0
b7
b0
Interrupt request register 1
(IREQ1 : address 003C16)
Interrupt request register 2
(IREQ2 : address 003D16)
INT0/Timer Z interrupt request bit
INT1 interrupt request bit
Serial I/O1 receive interrupt request bit
Serial I/O1 transmit/SCL, SDA interrupt
request bit
Timer X interrupt request bit
Timer Y interrupt request bit
Timer 1 interrupt request bit
Timer 2 interrupt request bit
CNTR0/SCL, SDA interrupt request bit
CNTR1/Serial I/O3 receive interrupt
request bit
Serial I/O2/Timer Z interrupt request bit
INT2/I2C interrupt request bit
INT3 interrupt request bit
INT4/CNTR2 interrupt request bit
AD converter/Serial I/O3 transmit
interrupt request bit
Not used (returns “0” when read)
0 : No interrupt request issued
1 : Interrupt request issued
b7
b0
b7
b0
Interrupt control register 2
(ICON2 : address 003F16)
Interrupt control register 1
(ICON1 : address 003E16)
INT0/Timer Z interrupt enable bit
INT1 interrupt enable bit
Serial I/O1 receive interrupt enable bit
Serial I/O1 transmit/SCL, SDA interrupt
enable bit
Timer X interrupt enable bit
Timer Y interrupt enable bit
Timer 1 interrupt enable bit
Timer 2 interrupt enable bit
CNTR0/SCL, SDA interrupt enable bit
CNTR1/Serial I/O3 receive interrupt
enable bit
Serial I/O2/Timer Z interrupt enable bit
INT2/I2C interrupt enable bit
INT3 interrupt enable bit
INT4/CNTR2 interrupt enable bit
AD converter/Serial I/O3 transmit
interrupt enable bit
Not used (returns “0” when read)
0 : Interrupts disabled
1 : Interrupts enabled
b0
b7
Interrupt source selection register
(INTSEL: address 003916)
INT0/Timer Z interrupt source selection bit
0 : INT0 interrupt
1 : Timer Z interrupt
(Do not write “1” to these bits simultaneously.)
(Do not write “1” to these bits simultaneously.)
Serial I/O2/Timer Z interrupt source selection bit
0 : Serial I/O2 interrupt
1 : Timer Z interrupt
Serial I/O1 transmit/SCL, SDA interrupt source selection bit
0 : Serial I/O1 transmit interrupt
1 : SCL, SDA interrupt
CNTR0/SCL, SDA interrupt source selection bit
0 : CNTR0 interrupt
1 : SCL, SDA interrupt
INT4/CNTR2 interrupt source selection bit
0 : INT4 interrupt
1 : CNTR2 interrupt
INT2/I2C interrupt source selection bit
0 : INT2 interrupt
1 : I2C interrupt
CNTR1/Serial I/O3 receive interrupt source selection bit
0 : CNTR1 interrupt
1 : Serial I/O3 receive interrupt
AD converter/Serial I/O3 transmit interrupt source selection bit
0 : A/D converter interrupt
1 : Serial I/O3 transmit interrupt
Fig. 20 Structure of interrupt-related registers
Rev.1.01 Jan 25, 2005 page 25 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
TIMERS
Timer X and Timer Y
ꢀ8-bit Timers
The timer X and timer Y can each select one of four operating
The 3804 group (Spec. H) has four 8-bit timers: timer 1, timer 2,
modes by setting the timer XY mode register (address 002316).
timer X, and timer Y.
The timer 1 and timer 2 use one prescaler in common, and the
timer X and timer Y use each prescaler. Those are 8-bit
prescalers. Each of the timers and prescalers has a timer latch or
a prescaler latch.
(1) Timer mode
ꢀMode selection
This mode can be selected by setting “00” to the timer X operating
mode bits (bits 1 and 0) and the timer Y operating mode bits (bits
5 and 4) of the timer XY mode register (address 002316).
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are down-counters. When the timer reaches “0016”, an
underflow occurs at the next count pulse and the contents of the
corresponding timer latch are reloaded into the timer and the
count is continued. When the timer underflows, the interrupt re-
quest bit corresponding to that timer is set to “1”.
ꢀExplanation of operation
The timer count operation is started by setting “0” to the timer X
count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the
timer XY mode register (address 002316).
When the timer reaches “0016”, an underflow occurs at the next
count pulse and the contents of timer latch are reloaded into the
timer and the count is continued.
ꢀTimer divider
The divider count source is switched by the main clock division
ratio selection bits of CPU mode register (bits 7 and 6 at address
003B16). When these bits are “00” (high-speed mode) or “01”
(middle-speed mode), XIN is selected. When these bits are“10”
(low-speed mode), XCIN is selected.
(2) Pulse output mode
ꢀMode selection
This mode can be selected by setting “01” to the timer X operating
mode bits (bits 1 and 0) and the timer Y operating mode bits (bits
5 and 4) of the timer XY mode register (address 002316).
ꢀExplanation of operation
ꢀPrescaler 12
The prescaler 12 counts the output of the timer divider. The count
source is selected by the timer 12, X count source selection
register among 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512,
1/1024 of f(XIN) or f(XCIN).
The operation is the same as the timer mode’s. Moreover the
pulse which is inverted each time the timer underflows is output
from CNTR0/CNTR1 pin. Regardless of the timer counting or not
the output of CNTR0/CNTR1 pin is initialized to the level of speci-
fied by their active edge switch bits when writing to the timer.
When the CNTR0 active edge switch bit (bit 2) and the CNTR1 ac-
tive edge switch bit (bit 6) of the timer XY mode register (address
002316) is “0”, the output starts with “H” level. When it is “1”, the
output starts with “L” level.
Timer 1 and Timer 2
The timer 1 and timer 2 counts the output of prescaler 12 and pe-
riodically set the interrupt request bit.
ꢀPrescaler X and prescaler Y
Switching the CNTR0 or CNTR1 active edge switch bit will reverse
the output level of the corresponding CNTR0 or CNTR1 pin.
ꢀPrecautions
The prescaler X and prescaler Y count the output of the timer
divider or f(XCIN). The count source is selected by the timer 12, X
count source selection register (address 000E16) and the timer Y,
Z count source selection register (address 000F16) among 1/2,
1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, and 1/1024 of f(XIN)
or f(XCIN); and f(XCIN).
Set the double-function port of CNTR0/CNTR1 pin and port P54/
P55 to output in this mode.
Rev.1.01 Jan 25, 2005 page 26 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(3) Event counter mode
ꢀMode selection
This mode can be selected by setting “10” to the timer X operating
mode bits (bits 1 and 0) and the timer Y operating mode bits (bits
5 and 4) of the timer XY mode register (address 002316).
ꢀExplanation of operation
The operation is the same as the timer mode’s except that the
timer counts signals input from the CNTR0 or CNTR1 pin. The
valid edge for the count operation depends on the CNTR0 active
edge switch bit (bit 2) or the CNTR1 active edge switch bit (bit 6)
of the timer XY mode register (address 002316). When it is “0”, the
rising edge is valid. When it is “1”, the falling edge is valid.
ꢀPrecautions
Set the double-function port of CNTR0/CNTR1 pin and port P54/
P55 to input in this mode.
(4) Pulse width measurement mode
ꢀMode selection
This mode can be selected by setting “11” to the timer X operating
mode bits (bits 1 and 0) and the timer Y operating mode bits (bits
5 and 4) of the timer XY mode register (address 002316).
ꢀExplanation of operation
When the CNTR0 active edge switch bit (bit 2) or the CNTR1 ac-
tive edge switch bit (bit 6) of the timer XY mode register (address
002316) is “1”, the timer counts during the term of one falling edge
of CNTR0/CNTR1 pin input until the next rising edge of input (“L”
term). When it is “0”, the timer counts during the term of one rising
edge input until the next falling edge input (“H” term).
ꢀPrecautions
Set the double-function port of CNTR0/CNTR1 pin and port P54/
P55 to input in this mode.
The count operation can be stopped by setting “1” to the timer X
count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the
timer XY mode register (address 002316). The interrupt request bit
is set to “1” each time the timer underflows.
•Precautions when switching count source
When switching the count source by the timer 12, X and Y count
source selection bits, the value of timer count is altered in incon-
siderable amount owing to generating of thin pulses on the count
input signals.
Therefore, select the timer count source before setting the value
to the prescaler and the timer.
Rev.1.01 Jan 25, 2005 page 27 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
X
IN
“00”
“01”
(1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, 1/1024)
Divider
Count source
selection bit
“10”
X
CIN
Data bus
Main clock
division ratio
selection bits
Prescaler X latch (8)
Timer X latch (8)
Timer X (8)
f(XCIN
)
Pulse width
Timer mode
Pulse output mode
measurement
mode
To timer X interrupt
request bit
Prescaler X (8)
CNTR
switch bit
0 active edge
Event
counter
mode
Timer X count stop bit
P5
4
/CNTR
0
“0”
“1”
To CNTR
0 interrupt
request bit
CNTR
edge switch bit
0
active
“1”
Q
Q
T
Toggle flip-flop
R
“0”
Port P5
latch
4
Timer X latch write pulse
Pulse output mode
Port P5
4
direction register
Pulse output mode
Data bus
Count source selection bit
Clock for timer Y
f(XCIN
Timer Y latch (8)
Timer Y (8)
Prescaler Y latch (8)
Pulse width
measurement
mode
)
Timer mode
Pulse output mode
To timer Y interrupt
request bit
Prescaler Y (8)
CNTR
switch bit
1
active edge
Event
counter
mode
Timer Y count stop bit
P55/CNTR1
“0”
“1”
To CNTR
1 interrupt
request bit
CNTR
edge switch bit
1
active
“1”
Q
Q
T
Toggle flip-flop
R
“0”
Port P5
latch
5
Timer Y latch write pulse
Pulse output mode
Port P5
direction register
5
Pulse output mode
Data bus
Timer 1 latch (8)
Timer 1 (8)
Timer 2 latch (8)
Timer 2 (8)
Prescaler 12 latch (8)
Prescaler 12 (8)
To timer 2 interrupt
request bit
Clock for timer 12
To timer 1 interrupt
request bit
Fig. 21 Block diagram of timer X, timer Y, timer 1, and timer 2
Rev.1.01 Jan 25, 2005 page 28 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Timer XY mode register
(TM : address 002316
)
Timer X operating mode bits
b1 b0
0
0
1
1
0 : Timer mode
1 : Pulse output mode
0 : Event counter mode
1 : Pulse width measurement mode
CNTR0 active edge switch bit
0 : Interrupt at falling edge
Count at rising edge in event counter mode
1 : Interrupt at rising edge
Count at falling edge in event counter mode
Timer X count stop bit
0 : Count start
1 : Count stop
Timer Y operating mode bits
b5 b4
0
0
1
1
0 : Timer mode
1 : Pulse output mode
0 : Event counter mode
1 : Pulse width measurement mode
CNTR1 active edge switch bit
0 : Interrupt at falling edge
Count at rising edge in event counter mode
1 : Interrupt at rising edge
Count at falling edge in event counter mode
Timer Y count stop bit
0 : Count start
1 : Count stop
Fig. 22 Structure of timer XY mode register
Rev.1.01 Jan 25, 2005 page 29 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Timer 12, X count source selection register
(T12XCSS : address 000E16
)
Timer 12 count source selection bits
b3b2b1b0
1010 :
1011 :
1100 :
1101 :
1110 :
1111 :
0 0 0 0 : f(X )/2 or f(X )/2
0 0 0 1 : f(XIN)/4 or f(XCIN)/4
0 0 1 0 : f(XIN)/8 or f(XCCIINN)/8
0 0 1 1 : f(XIN)/16 or f(X )/16
0 1 0 0 : f(XIN)/32 or f(XCIN)/32
0 1 0 1 : f(XIN)/64 or f(XCCIINN)/64
0 1 1 0 : f(XIN)/128 or f(X )/128
0 1 1 1 : f(XIN)/256 or f(XCIN)/256
1 0 0 0 : f(XIN)/512 or f(XCCIINN)/512
1 0 0 1 : f(XIINN)/1024 or f(XCIN)/1024
Not used
Timer X count source selection bits
b7b6b5b4
0 0 0 0 : f(X )/2 or f(X )/2
0 0 0 1 : f(XIN)/4 or f(XCIN)/4
0 0 1 0 : f(XIN)/8 or f(XCCIINN)/8
0 0 1 1 : f(XIN)/16 or f(X )/16
0 1 0 0 : f(XIN)/32 or f(XCIN)/32
0 1 0 1 : f(XIN)/64 or f(XCCIINN)/64
0 1 1 0 : f(XIN)/128 or f(X )/128
0 1 1 1 : f(XIN)/256 or f(XCIN)/256
1 0 0 0 : f(XIN)/512 or f(XCCIINN)/512
1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024
1011 :
1100 :
1101 : Not used
1110 :
1111 :
1 0 1 0 : f(XCININ
)
b7
b0
Timer Y, Z count source selection register
(TYZCSS : address 000F16
)
Timer Y count source selection bits
b3b2b1b0
0 0 0 0 : f(X )/2 or f(X )/2
0 0 0 1 : f(XIN)/4 or f(XCIN)/4
0 0 1 0 : f(XIN)/8 or f(XCCIINN)/8
0 0 1 1 : f(XIN)/16 or f(X )/16
0 1 0 0 : f(XIN)/32 or f(XCIN)/32
0 1 0 1 : f(XIN)/64 or f(XCCIINN)/64
0 1 1 0 : f(XIN)/128 or f(X )/128
0 1 1 1 : f(XIN)/256 or f(XCIN)/256
1 0 0 0 : f(XIN)/512 or f(XCCIINN)/512
1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024
1011 :
1100 :
1101 :
1110 :
1111 :
Not used
1 0 1 0 : f(XCININ
)
Timer Z count source selection bits
b7b6b5b4
0 0 0 0 : f(X )/2 or f(X )/2
0 0 0 1 : f(XIN)/4 or f(XCIN)/4
0 0 1 0 : f(XIN)/8 or f(XCCIINN)/8
0 0 1 1 : f(XIN)/16 or f(X )/16
0 1 0 0 : f(XIN)/32 or f(XCIN)/32
0 1 0 1 : f(XIN)/64 or f(XCCIINN)/64
0 1 1 0 : f(XIN)/128 or f(X )/128
0 1 1 1 : f(XIN)/256 or f(XCIN)/256
1 0 0 0 : f(XIN)/512 or f(XCCIINN)/512
1 0 0 1 : f(XIN)/1024 or f(XCIN)/1024
1011 :
1100 :
1101 : Not used
1110 :
1111 :
1 0 1 0 : f(XCININ
)
Fig. 23 Structure of timer 12, X and timer Y, Z count source selection registers
Rev.1.01 Jan 25, 2005 page 30 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
●16-bit Timer
(2) Event counter mode
The timer Z is a 16-bit timer. When the timer reaches “000016”, an
underflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When the timer underflows, the interrupt request bit corresponding
to the timer Z is set to “1”.
●Mode selection
This mode can be selected by setting “000” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “1” to the timer/event
counter mode switch bit (bit 7) of the timer Z mode register (ad-
dress 002A16).
When reading/writing to the timer Z, perform reading/writing to
both the high-order byte and the low-order byte. When reading the
timer Z, read from the high-order byte first, followed by the low-or-
der byte. Do not perform the writing to the timer Z between read
operation of the high-order byte and read operation of the low-or-
der byte. When writing to the timer Z, write to the low-order byte
first, followed by the high-order byte. Do not perform the reading
to the timer Z between write operation of the low-order byte and
write operation of the high-order byte.
The valid edge for the count operation depends on the CNTR2 ac-
tive edge switch bit (bit 5) of the timer Z mode register (address
002A16). When it is “0”, the rising edge is valid. When it is “1”, the
falling edge is valid.
●Interrupt
The interrupt at an underflow is the same as the timer mode’s.
●Explanation of operation
The operation is the same as the timer mode’s.
Set the double-function port of CNTR2 pin and port P47 to input in
this mode.
The timer Z can select the count source by the timer Z count
source selection bits of timer Y, Z count source selection register
(bits 7 to 4 at address 000F16).
Figure 26 shows the timing chart of the timer/event counter mode.
Timer Z can select one of seven operating modes by setting the
timer Z mode register (address 002A16).
(3) Pulse output mode
●Mode selection
This mode can be selected by setting “001” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
(1) Timer mode
●Mode selection
This mode can be selected by setting “000” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
●Count source selection
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/
128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as
the count source.
●Count source selection
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/
128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as
the count source.
In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/
512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count
source.
In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/
512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count
source.
●Interrupt
The interrupt at an underflow is the same as the timer mode’s.
●Explanation of operation
●Interrupt
The operation is the same as the timer mode’s. Moreover the
pulse which is inverted each time the timer underflows is output
from CNTR2 pin. When the CNTR2 active edge switch bit (bit 5) of
the timer Z mode register (address 002A16) is “0”, the output starts
with “H” level. When it is “1”, the output starts with “L” level.
●Precautions
When an underflow occurs, the INT0/timer Z interrupt request bit
(bit 0) of the interrupt request register 1 (address 003C16) is set to
“1”.
●Explanation of operation
During timer stop, usually write data to a latch and a timer at the
same time to set the timer value.
The double-function port of CNTR2 pin and port P47 is automati-
cally set to the timer pulse output port in this mode.
The output from CNTR2 pin is initialized to the level depending on
CNTR2 active edge switch bit by writing to the timer.
When the value of the CNTR2 active edge switch bit is changed,
the output level of CNTR2 pin is inverted.
The timer count operation is started by setting “0” to the timer Z
count stop bit (bit 6) of the timer Z mode register (address
002A16).
When the timer reaches “000016”, an underflow occurs at the next
count pulse and the contents of timer latch are reloaded into the
timer and the count is continued.
Figure 27 shows the timing chart of the pulse output mode.
When writing data to the timer during operation, the data is written
only into the latch. Then the new latch value is reloaded into the
timer at the next underflow.
Rev.1.01 Jan 25, 2005 page 31 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(4) Pulse period measurement mode
ꢀMode selection
(5) Pulse width measurement mode
ꢀMode selection
This mode can be selected by setting “010” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
This mode can be selected by setting “011” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
ꢀCount source selection
ꢀCount source selection
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64,
1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected
as the count source.
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64,
1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected
as the count source.
In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256,
1/512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count
source.
In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256,
1/512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count
source.
ꢀInterrupt
ꢀInterrupt
The interrupt at an underflow is the same as the timer mode’s.
When the pulse period measurement is completed, the INT4/
CNTR2 interrupt request bit (bit 5) of the interrupt request register
2 (address 003D16) is set to “1”.
The interrupt at an underflow is the same as the timer mode’s.
When the pulse widths measurement is completed, the INT4/
CNTR2 interrupt request bit (bit 5) of the interrupt request register
2 (address 003D16) is set to “1”.
ꢀExplanation of operation
ꢀExplanation of operation
The cycle of the pulse which is input from the CNTR2 pin is mea-
sured. When the CNTR2 active edge switch bit (bit 5) of the timer
Z mode register (address 002A16) is “0”, the timer counts during
the term from one falling edge of CNTR2 pin input to the next fall-
ing edge. When it is “1”, the timer counts during the term from one
rising edge input to the next rising edge input.
When the valid edge of measurement completion/start is detected,
the 1’s complement of the timer value is written to the timer latch
and “FFFF16” is set to the timer.
The pulse width which is input from the CNTR2 pin is measured.
When the CNTR2 active edge switch bit (bit 5) of the timer Z mode
register (address 002A16) is “0”, the timer counts during the term
from one rising edge input to the next falling edge input (“H” term).
When it is “1”, the timer counts during the term from one falling
edge of CNTR2 pin input to the next rising edge of input (“L” term).
When the valid edge of measurement completion is detected, the
1’s complement of the timer value is written to the timer latch.
When the valid edge of measurement completion/start is detected,
“FFFF16” is set to the timer.
Furthermore when the timer underflows, the timer Z interrupt re-
quest occurs and “FFFF16” is set to the timer. When reading the
timer Z, the value of the timer latch (measured value) is read. The
measured value is retained until the next measurement comple-
tion.
When the timer Z underflows, the timer Z interrupt occurs and
“FFFF16” is set to the timer Z. When reading the timer Z, the value
of the timer latch (measured value) is read. The measured value is
retained until the next measurement completion.
ꢀPrecautions
ꢀPrecautions
Set the double-function port of CNTR2 pin and port P47 to input in
this mode.
Set the double-function port of CNTR2 pin and port P47 to input in
this mode.
A read-out of timer value is impossible in this mode. The timer can
be written to only during timer stop (no measurement of pulse pe-
riod).
A read-out of timer value is impossible in this mode. The timer can
be written to only during timer stop (no measurement of pulse
widths).
Since the timer latch in this mode is specialized for the read-out of
measured values, do not perform any write operation during mea-
surement.
Since the timer latch in this mode is specialized for the read-out of
measured values, do not perform any write operation during mea-
surement.
“FFFF16” is set to the timer when the timer underflows or when the
valid edge of measurement start/completion is detected. Conse-
quently, the timer value at start of pulse period measurement
depends on the timer value just before measurement start.
Figure 28 shows the timing chart of the pulse period measurement
mode.
“FFFF16” is set to the timer when the timer underflows or when the
valid edge of measurement start/completion is detected. Conse-
quently, the timer value at start of pulse width measurement
depends on the timer value just before measurement start.
Figure 29 shows the timing chart of the pulse width measurement
mode.
Rev.1.01 Jan 25, 2005 page 32 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(6) Programmable waveform generating mode
●Mode selection
•“L” one-shot pulse; Bit 5 of timer Z mode register = “1”
The output level of the CNTR2 pin is initialized to “H” at mode se-
lection. When trigger generation (input signal to INT1 pin) is
detected, “L” is output from the CNTR2 pin. When an underflow
occurs, “H” is output. The “L” one-shot pulse width is set by the
setting value to the timer Z low-order and high-order. When trigger
generating is detected during timer count stop, although “L” is out-
put from the CNTR2 pin, “L” output state continues because an
underflow does not occur.
This mode can be selected by setting “100” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
●Count source selection
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64,
1/128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected
as the count source.
●Precautions
In low-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/
512 or 1/1024 of f(XCIN); or f(XCIN) can be selected as the count
source.
Set the double-function port of INT1 pin and port P42 to input in
this mode.
Set the double-function port of CNTR2 pin and port P22 is auto-
matically set to the programmable one-shot generating port in this
mode.
●Interrupt
The interrupt at an underflow is the same as the timer mode’s.
●Explanation of operation
This mode cannot be used in low-speed mode.
If the value of the CNTR2 active edge switch bit is changed during
one-shot generating enabled or generating one-shot pulse, then
the output level from CNTR2 pin changes.
The operation is the same as the timer mode’s. Moreover the
timer outputs the data set in the output level latch (bit 4) of the
timer Z mode register (address 002A16) from the CNTR2 pin each
time the timer underflows.
Figure 31 shows the timing chart of the programmable one-shot
generating mode.
Changing the value of the output level latch and the timer latch af-
ter an underflow makes it possible to output an optional waveform
from the CNTR2 pin.
●Notes regarding all modes
●Timer Z write control
●Precautions
The double-function port of CNTR2 pin and port P47 is automati-
cally set to the programmable waveform generating port in this
mode.
Which write control can be selected by the timer Z write control bit
(bit 3) of the timer Z mode register (address 002A16), writing data
to both the latch and the timer at the same time or writing data
only to the latch.
Figure 30 shows the timing chart of the programmable waveform
generating mode.
When the operation “writing data only to the latch” is selected, the
value is set to the timer latch by writing data to the address of
timer Z and the timer is updated at next underflow. After reset re-
lease, the operation “writing data to both the latch and the timer at
the same time” is selected, and the value is set to both the latch
and the timer at the same time by writing data to the address of
timer Z.
(7) Programmable one-shot generating mode
●Mode selection
This mode can be selected by setting “101” to the timer Z operat-
ing mode bits (bits 2 to 0) and setting “0” to the timer/event
counter mode switch bit (b7) of the timer Z mode register (address
002A16).
In the case of writing data only to the latch, if writing data to the
latch and an underflow are performed almost at the same time,
the timer value may become undefined.
●Count source selection
In high- or middle-speed mode, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/
128, 1/256, 1/512 or 1/1024 of f(XIN); or f(XCIN) can be selected as
the count source.
●Timer Z read control
A read-out of timer value is impossible in pulse period measure-
ment mode and pulse width measurement mode. In the other
modes, a read-out of timer value is possible regardless of count
operating or stopped.
●Interrupt
The interrupt at an underflow is the same as the timer mode’s.
The trigger to generate one-shot pulse can be selected by the
INT1 active edge selection bit (bit 1) of the interrupt edge selection
register (address 003A16). When it is “0”, the falling edge active is
selected; when it is “1”, the rising edge active is selected.
When the valid edge of the INT1 pin is detected, the INT1 interrupt
request bit (bit 1) of the interrupt request register 1 (address
003C16) is set to “1”.
However, a read-out of timer latch value is impossible.
●Switch of interrupt active edge of CNTR2 and INT1
Each interrupt active edge depends on setting of the CNTR2 ac-
tive edge switch bit and the INT1 active edge selection bit.
●Switch of count source
When switching the count source by the timer Z count source se-
lection bits, the value of timer count is altered in inconsiderable
amount owing to generating of thin pulses on the count input sig-
nals.
●Explanation of operation
•“H” one-shot pulse; Bit 5 of timer Z mode register = “0”
The output level of the CNTR2 pin is initialized to “L” at mode se-
lection. When trigger generation (input signal to INT1 pin) is
detected, “H” is output from the CNTR2 pin. When an underflow
occurs, “L” is output. The “H” one-shot pulse width is set by the
setting value to the timer Z register low-order and high-order.
When trigger generating is detected during timer count stop, al-
though “H” is output from the CNTR2 pin, “H” output state
continues because an underflow does not occur.
Therefore, select the timer count source before setting the value
to the prescaler and the timer.
●Usage of CNTR2 pin as normal I/O port
To use the CNTR2 pin as normal I/O port P47, set timer Z operat-
ing mode bits (b2, b1, b0) of timer Z mode register (address
002A16) to “000”.
Rev.1.01 Jan 25, 2005 page 33 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
CNTR
2 active edge
Data bus
Programmable one-shot
generating mode
switch bit
“1”
P42/INT1
Programmable one-shot
generating circuit
Programmable one-shot
generating mode
“0”
To INT1 interrupt
request bit
Programmable waveform
generating mode
D
T
Output level latch
Q
Pulse output mode
CNTR
2
active edge switch bit
Pulse output mode
S
“0”
Q
Q
T
“1”
“001”
“100”
“101”
Timer Z operating
mode bits
Timer Z low-order latch Timer Z high-order latch
Timer Z low-order Timer Z high-order
Port P4
latch
7
To timer Z interrupt
request bit
Port P4
7
direction register
Pulse period measurement mode
Pulse width measurement mode
Edge detection circuit
To CNTR
request bit
2 interrupt
“1”
“0”
“1”
f(XCIN
)
P47/CNTR2
“0”
Timer Z count stop bit
CNTR
switch bit
2 active edge
Timer/Event
counter mode
switch bit
XIN
Count source
selection bit
Divider
(1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, 1/1024)
XCIN
Fig. 24 Block diagram of timer Z
Rev.1.01 Jan 25, 2005 page 34 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Timer Z mode register
(TZM : address 002A16
)
Timer Z operating mode bits
b2b1b0
0 0 0 : Timer/Event counter mode
0 0 1 : Pulse output mode
0 1 0 : Pulse period measurement mode
0 1 1 : Pulse width measurement mode
1 0 0 : Programmable waveform generating mode
1 0 1 : Programmable one-shot generating mode
1 1 0 : Not available
1 1 1 : Not available
Timer Z write control bit
0 : Writing data to both latch and timer simultaneously
1 : Writing data only to latch
Output level latch
0 : “L” output
1 : “H” output
CNTR active edge switch bit
2
0 : •Event counter mode: Count at rising edge
•Pulse output mode: Start outputting “H”
•Pulse period measurement mode: Measurement
between two falling edges
•Pulse width measurement mode: Measurement of
“H” term
•Programmable one-shot generating mode: After
start outputting “L”, “H” one-shot pulse generated
•Interrupt at falling edge
1 : •Event counter mode: Count at falling edge
•Pulse output mode: Start outputting “L”
•Pulse period measurement mode: Measurement
between two rising edges
•Pulse width measurement mode: Measurement of
“L” term
•Programmable one-shot generating mode: After
start outputting “H”, “L” one-shot pulse generated
•Interrupt at rising edge
Timer Z count stop bit
0 : Count start
1 : Count stop
Timer/Event counter mode switch bit (Note)
0 : Timer mode
1 : Event counter mode
Note: When selecting the modes except the timer/event
counter mode, set “0” to this bit.
Fig. 25 Structure of timer Z mode register
Rev.1.01 Jan 25, 2005 page 35 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
FFFF16
TL
000016
TR
TR
TR
TL : Value set to timer latch
TR : Timer interrupt request
Fig. 26 Timing chart of timer/event counter mode
FFFF16
TL
000016
TR
TR
TR
TR
Waveform output
from CNTR pin
2
CNTR
2
CNTR
2
TL : Value set to timer latch
TR : Timer interrupt request
CNTR
2
: CNTR
2 interrupt request
(CNTR
2
active edge switch bit = “0”; Falling edge active)
Fig. 27 Timing chart of pulse output mode
Rev.1.01 Jan 25, 2005 page 36 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
000016
T3
T2
T1
FFFF16
TR
TR
T2
T3
FFFF16 + T1
FFFF16
Signal input from
CNTR pin
2
CNTR
2
CNTR
2
CNTR
2
CNTR2
CNTR
TR : Timer interrupt request
CNTR : CNTR interrupt request
2 of rising edge active
2
2
Fig. 28 Timing chart of pulse period measurement mode (Measuring term between two rising edges)
000016
T3
T2
T1
FFFF16
TR
T1
FFFF16 + T2
T3
Signal input from
CNTR pin
2
CNTR
2
CNTR
interrupt of rising edge active; Measurement of “L” width
TR : Timer interrupt request
CNTR : CNTR interrupt request
2
CNTR2
CNTR
2
2
2
Fig. 29 Timing chart of pulse width measurement mode (Measuring “L” term)
Rev.1.01 Jan 25, 2005 page 37 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
FFFF16
T3
L
T2
T1
000016
Signal output
from CNTR2 pin
L
T3
T1
TR
CNTR2
L : Timer initial value
T2
TR
TR
TR
CNTR2
TR : Timer interrupt request
CNTR2 : CNTR2 interrupt request
(CNTR2 active edge switch bit = “0”; Falling edge active)
Fig. 30 Timing chart of programmable waveform generating mode
FFFF16
L
TR
TR
TR
Signal input from
INT pin
1
Signal output
from CNTR pin
L
L
L
2
CNTR
2
CNTR2
L : One-shot pulse width
TR : Timer interrupt request
CNTR : CNTR interrupt request
(CNTR active edge switch bit = “0”; Falling edge active)
2
2
2
Fig. 31 Timing chart of programmable one-shot generating mode (“H” one-shot pulse generating)
Rev.1.01 Jan 25, 2005 page 38 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
SERIAL INTERFACE
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O1 mode can be selected by setting
the serial I/O1 mode selection bit of the serial I/O1 control register
(bit 6 of address 001A16) to “1”.
Serial I/O1
Serial I/O1 can be used as either clock synchronous or asynchro-
nous (UART) serial I/O1. A dedicated timer is also provided for
baud rate generation.
For clock synchronous serial I/O, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the transmit/receive buffer register.
Data bus
Serial I/O1 control register
Receive buffer full flag (RBF)
Address 001A16
Address 001816
Receive buffer register 1
Receive shift register 1
Receive interrupt request (RI)
P44/RXD1
Shift clock
Clock control circuit
P46/SCLK1
Serial I/O1 synchronous
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
(f(XCIN) in low-speed mode)
f(XIN
)
Baud rate generator 1
Address 001C16
1/4
1/4
Clock control circuit
Falling-edge detector
P47/SRDY1
F/F
Shift clock
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
P4
5/T
XD1
Transmit shift register 1
Transmit buffer register 1
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Serial I/O1 status register
Address 001916
Address 001816
Data bus
Fig. 32 Block diagram of clock synchronous serial I/O1
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD1
Serial input RxD1
D0
D0
D1
D1
D2
D2
D3
D3
D4
D4
D5
D5
D6
D6
D7
D7
Receive enable signal SRDY1
Write pulse to receive/transmit
buffer register (address 001816)
RBF = 1
TSC = 1
TBE = 0
TBE = 1
TSC = 0
Overrun error (OE)
detection
Notes
1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the
transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1
control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data
is output continuously from the TxD pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 33 Operation of clock synchronous serial I/O1
Rev.1.01 Jan 25, 2005 page 39 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O1 mode selection bit of the serial I/O1 control
register to “0”.
two buffers have the same address in a memory. Since the shift
register cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but the
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Data bus
Address 001816
Address 001A16
Serial I/O1 control register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
OE
Receive buffer register 1
Character length selection bit
7 bits
P44/RX
D
1
ST detector
Receive shift register 1
1/16
8 bits
UART1 control register
PE FE
SP detector
Address 001B16
Clock control circuit
Serial I/O1 synchronous clock selection bit
P46/SCLK1
Frequency division ratio 1/(n+1)
BRG count source selection bit
f(XIN
)
Baud rate generator
Address 001C16
(f(XCIN) in low-speed mode)
1/4
ST/SP/PA generator
1/16
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
P45/TXD1
Transmit shift register 1
Transmit interrupt request (TI)
Character length selection bit
Transmit buffer empty flag (TBE)
Transmit buffer register 1
Address 001816
Address 001916
Serial I/O1 status register
Data bus
Fig. 34 Block diagram of UART serial I/O1
Transmit or receive clock
Transmit buffer write
signal
TBE=0
TSC=0
TBE=0
TSC=1ꢀ
TBE=1
TBE=1
Serial output TXD1
ST
SP
D0
D1
ST
D0
D1
SP
ꢀ Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Receive buffer read
signal
RBF=0
RBF=1
SP
RBF=1
SP
ST
Serial input RXD1
D0
D1
ST
D0
D1
Notes
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0.
Fig. 35 Operation of UART serial I/O1
Rev.1.01 Jan 25, 2005 page 40 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
[Serial I/O1 Control Register (SIO1CON)]
001A16
The serial I/O1 control register consists of eight control bits for the
serial I/O1 function.
[UART1 Control Register (UART1CON)]
001B16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer, and one bit (bit 4) which is al-
ways valid and sets the output structure of the P45/TXD1 pin.
[Serial I/O1 Status Register (SIO1STS)]
001916
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O1
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O1
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE
(bit 7 of the serial I/O1 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O1 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
[Transmit Buffer Register 1/Receive Buffer
Register 1 (TB1/RB1)] 001816
The transmit buffer register 1 and the receive buffer register 1 are
located at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Baud Rate Generator 1 (BRG1)] 001C16
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
Rev.1.01 Jan 25, 2005 page 41 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
b0
b7
Serial I/O1 status register
(SIO1STS : address 001916
Serial I/O1 control register
(SIO1CON : address 001A16
)
)
BRG count source selection bit (CSS)
0: f(XIN) (f(XCIN) in low-speed mode)
1: f(XIN)/4 (f(XCIN)/4 in low-speed mode)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
Serial I/O1 synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous
serial I/O is selected, BRG output divided by 16
when UART is selected.
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
1: External clock input when clock synchronous serial
I/O is selected, external clock input divided by 16
when UART is selected.
Transmit shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
S
0: P4
1: P4
RDY1 output enable bit (SRDY)
Overrun error flag (OE)
0: No error
1: Overrun error
7
pin operates as normal I/O pin
pin operates as SRDY1 output pin
7
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Parity error flag (PE)
0: No error
1: Parity error
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Framing error flag (FE)
0: No error
1: Framing error
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Summing error flag (SE)
0: (OE) U (PE) U (FE)=0
1: (OE) U (PE) U (FE)=1
Serial I/O1 mode selection bit (SIOM)
0: Clock asynchronous (UART) serial I/O
1: Clock synchronous serial I/O
Not used (returns “1” when read)
Serial I/O1 enable bit (SIOE)
0: Serial I/O1 disabled
(pins P4
1: Serial I/O1 enabled
(pins P4 to P4 operate as serial I/O pins)
4 to P47 operate as normal I/O pins)
4
7
b7
b0
UART1 control register
(UART1CON : address 001B16
)
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (STPS)
0: 1 stop bit
1: 2 stop bits
P45/TXD1 P-channel output disable bit (POFF)
0: CMOS output (in output mode)
1: N-channel open drain output (in output mode)
Not used (return “1” when read)
Fig. 36 Structure of serial I/O1 control registers
Rev.1.01 Jan 25, 2005 page 42 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀ Notes concerning serial I/O1
1. Notes when selecting clock synchronous serial I/O
1.1 Stop of transmission operation
2. Notes when selecting clock asynchronous serial I/O
2.1 Stop of transmission operation
ꢀ Note
ꢀ Note
Clear the transmit enable bit to “0” (transmit disabled). The trans-
mission operation does not stop by clearing the serial I/O1 enable
bit to “0”.
Clear the serial I/O1 enable bit and the transmit enable bit to “0”
(serial I/O and transmit disabled).
ꢀ Reason
ꢀ Reason
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O1 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O1 enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD1 pin and an operation failure occurs.
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O1 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O1 enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD1 pin and an operation failure occurs.
1.2 Stop of receive operation
2.2 Stop of receive operation
ꢀ Note
ꢀ Note
Clear the receive enable bit to “0” (receive disabled), or clear the
serial I/O1 enable bit to “0” (serial I/O disabled).
Clear the receive enable bit to “0” (receive disabled).
2.3 Stop of transmit/receive operation
1.3 Stop of transmit/receive operation
ꢀ Note
ꢀ Note 1 (only transmission operation is stopped)
Clear the transmit enable bit to “0” (transmit disabled). The trans-
mission operation does not stop by clearing the serial I/O1 enable
bit to “0”.
Clear both the transmit enable bit and receive enable bit to “0”
(transmit and receive disabled).
(when data is transmitted and received in the clock synchronous
serial I/O mode, any one of data transmission and reception can-
not be stopped.)
ꢀ Reason
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O1 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD1, RxD1, SCLK1, and SRDY1 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O1 enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD1 pin and an operation failure occurs.
ꢀ Reason
In the clock synchronous serial I/O mode, the same clock is used
for transmission and reception. If any one of transmission and re-
ception is disabled, a bit error occurs because transmission and
reception cannot be synchronized.
In this mode, the clock circuit of the transmission circuit also oper-
ates for data reception. Accordingly, the transmission circuit does
not stop by clearing only the transmit enable bit to “0” (transmit
disabled). Also, the transmission circuit is not initialized by clear-
ing the serial I/O1 enable bit to “0” (serial I/O disabled) (refer to
1.1).
ꢀ Note 2 (only receive operation is stopped)
Clear the receive enable bit to “0” (receive disabled).
Rev.1.01 Jan 25, 2005 page 43 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
3. SRDY1 output of reception side
7. Transmit interrupt request when transmit enable bit is set
ꢀ Note
ꢀ Note
When signals are output from the SRDY1 pin on the reception side
by using an external clock in the clock synchronous serial I/O
mode, set all of the receive enable bit, the SRDY1 output enable
bit, and the transmit enable bit to “1” (transmit enabled).
When using the transmit interrupt, take the following sequence.
ꢀ Set the serial I/O1 transmit interrupt enable bit to “0” (disabled).
ꢀ Set the transmit enable bit to “1”.
ꢀ Set the serial I/O1 transmit interrupt request bit to “0” after 1 or
more instruction has executed.
4. Setting serial I/O1 control register again
ꢀ Note
ꢀ Set the serial I/O1 transmit interrupt enable bit to “1” (enabled).
ꢀ Reason
Set the serial I/O1 control register again after the transmission and
the reception circuits are reset by clearing both the transmit en-
able bit and the receive enable bit to “0.”
When the transmit enable bit is set to “1”, the transmit buffer
empty flag and the transmit shift register shift completion flag are
also set to “1”. Therefore, regardless of selecting which timing for
the generating of transmit interrupts, the interrupt request is gener-
ated and the transmit interrupt request bit is set at this point.
Clear both the transmit enable bit
(TE) and the receive enable bit
(RE) to “0”
↓
Set the bits 0 to 3 and bit 6 of the
serial I/O control register
Can be set with the
↓
LDM instruction at the
same time
Set both the transmit enable bit
(TE) and the receive enable bit
(RE), or one of them to “1”
5. Data transmission control with referring to transmit shift
register completion flag
ꢀ Note
After the transmit data is written to the transmit buffer register, the
transmit shift register completion flag changes from “1” to “0” with
a delay of 0.5 to 1.5 shift clocks. When data transmission is con-
trolled with referring to the flag after writing the data to the transmit
buffer register, note the delay.
6. Transmission control when external clock is selected
ꢀ Note
When an external clock is used as the synchronous clock for data
transmission, set the transmit enable bit to “1” at “H” of the SCLK1
input level. Also, write data to the transmit buffer register at “H” of
the SCLK1 input level.
Rev.1.01 Jan 25, 2005 page 44 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
Serial I/O2
b0
Serial I/O2 control register
(SIO2CON : address 001D16)
The serial I/O2 function can be used only for clock synchronous
serial I/O2.
Internal synchronous clock selection bits
b2 b1 b0
For clock synchronous serial I/O2, the transmitter and the receiver
must use the same clock. If the internal clock is used, transfer is
started by a write signal to the serial I/O2 register.
0 0 0: f(XIN)/8 (f(XCIN)/8 in low-speed mode)
0 0 1: f(XIN)/16 (f(XCIN)/16 in low-speed mode)
0 1 0: f(XIN)/32 (f(XCIN)/32 in low-speed mode)
0 1 1: f(XIN)/64 (f(XCIN)/64 in low-speed mode)
1 1 0: f(XIN)/128 (f(XCIN)/128 in low-speed mode)
1 1 1: f(XIN)/256 (f(XCIN)/256 in low-speed mode)
[Serial I/O2 Control Register (SIO2CON)]
001D16
Serial I/O2 port selection bit
0: I/O port
1: SOUT2,SCLK2 signal output
The serial I/O2 control register contains eight bits which control
various serial I/O2 functions.
SRDY2 output enable bit
0: I/O port
1: SRDY2 signal output
Transfer direction selection bit
0: LSB first
1: MSB first
Serial I/O2 synchronous clock selection bit
0: External clock
1: Internal clock
P51/SOUT2 P-channel output disable bit
0: CMOS output (in output mode)
1: N-channel open drain output (in output mode)
Fig. 37 Structure of serial I/O2 control register
Internal synchronous
clock selection bits
1/8
1/16
Data bus
1/32
f(XIN
)
1/64
(f(XCIN) in low-speed mode)
1/128
1/256
P53 latch
Serial I/O2 synchronous
clock selection bit
“0”
“1”
P53/SRDY2
S
RDY2
Synchronization
circuit
“1”
SRDY2 output enable bit
“0”
External clock
P52 latch
“0”
P52/SCLK2
Serial I/O2
interrupt request
Serial I/O counter 2 (3)
“1”
Serial I/O2 port selection bit
P51 latch
“0”
P51/SOUT2
“1”
Serial I/O2 port selection bit
Serial I/O2 register (8)
P50/SIN2
Address 001F16
Fig. 38 Block diagram of serial I/O2
Rev.1.01 Jan 25, 2005 page 45 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Transfer clock (Note 1)
Serial I/O2 register
write signal
(Note 2)
Serial I/O2 output
SOUT2
D2
D0
D1
D3
D4
D5
D6
D7
Serial I/O2 input SIN2
Receive enable signal SRDY2
Serial I/O2 interrupt request bit set
Notes 1: When the internal clock is selected as the transfer clock, the divide ratio of f(XIN), or f(XCIN) in low-speed mode, can be
selected by setting bits 0 to 2 of the serial I/O2 control register.
2: When the internal clock is selected as the transfer clock, the SOUT2 pin goes to high impedance after transfer completion.
Fig. 39 Timing of serial I/O2
Rev.1.01 Jan 25, 2005 page 46 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Serial I/O3
(1) Clock Synchronous Serial I/O Mode
Clock synchronous serial I/O3 mode can be selected by setting
the serial I/O3 mode selection bit of the serial I/O3 control register
(bit 6 of address 003216) to “1”.
Serial I/O3 can be used as either clock synchronous or asynchro-
nous (UART) serial I/O3. A dedicated timer is also provided for
baud rate generation.
For clock synchronous serial I/O, the transmitter and the receiver
must use the same clock. If an internal clock is used, transfer is
started by a write signal to the transmit/receive buffer register.
Data bus
Serial I/O3 control register
Receive buffer full flag (RBF)
Address 003216
Address 003016
Receive buffer register 3
Receive shift register 3
Receive interrupt request (RI)
P34/RXD3
Shift clock
Clock control circuit
P36/SCLK3
Serial I/O3 synchronous
clock selection bit
Frequency division ratio 1/(n+1)
BRG count source selection bit
(f(XCIN) in low-speed mode)
f(XIN
)
Baud rate generator 3
Address 002F16
1/4
1/4
Clock control circuit
Falling-edge detector
P37/SRDY3
F/F
Shift clock
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
P3
5/T
XD3
Transmit shift register 3
Transmit buffer register 3
Transmit interrupt request (TI)
Transmit buffer empty flag (TBE)
Serial I/O3 status register
Address 003116
Address 003016
Data bus
Fig. 40 Block diagram of clock synchronous serial I/O3
Transfer shift clock
(1/2 to 1/2048 of the internal
clock, or an external clock)
Serial output TxD
Serial input RxD
3
3
D
0
0
D
1
D
2
2
D
3
3
D
4
4
D
5
5
D
6
6
D
7
7
D
D1
D
D
D
D
D
D
Receive enable signal SRDY3
Write pulse to receive/transmit
buffer register (address 003016
)
RBF = 1
TSC = 1
TBE = 0
TBE = 1
TSC = 0
Overrun error (OE)
detection
Notes
1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the
transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O3
control register.
2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data
is output continuously from the TxD pin.
3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .
Fig. 41 Operation of clock synchronous serial I/O3
Rev.1.01 Jan 25, 2005 page 47 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O3 mode selection bit of the serial I/O3 control
register to “0”.
two buffers have the same address in a memory. Since the shift
register cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but the
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Data bus
Serial I/O3 control register Address 003216
Address 003016
Receive buffer register 3
Receive buffer full flag (RBF)
Receive interrupt request (RI)
OE
Character length selection bit
P34/RXD3
ST detector
7 bits
8 bits
Receive shift register 3
1/16
UART3 control register
PE FE SP detector
Address 003316
Clock control circuit
Serial I/O3 synchronous clock selection bit
P36/SCLK3
f(XIN)
Frequency division ratio 1/(n+1)
BRG count source selection bit
Baud rate generator 3
Address 002F16
(f(XCIN) in low-speed mode)
1/4
ST/SP/PA generator
1/16
Transmit shift completion flag (TSC)
Transmit interrupt source selection bit
Transmit shift register 3
P35/TXD3
Transmit interrupt request (TI)
Character length selection bit
Transmit buffer empty flag (TBE)
Transmit buffer register 3
Address 003016
Address 003116
Serial I/O3 status register
Data bus
Fig. 42 Block diagram of UART serial I/O3
Transmit or receive clock
Transmit buffer write
signal
TBE=0
TSC=0
TBE=0
TSC=1ꢀ
SP
TBE=1
TBE=1
Serial output TXD3
ST
D0
D1
ST
D0
D1
SP
ꢀ Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
Receive buffer read
signal
RBF=0
RBF=1
SP
RBF=1
SP
ST
Serial input R
X
D3
D0
D1
ST
D0
D1
Notes
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O3 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0.
Fig. 43 Operation of UART serial I/O3
Rev.1.01 Jan 25, 2005 page 48 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
[Serial I/O3 Control Register (SIO3CON)]
003216
The serial I/O3 control register consists of eight control bits for the
serial I/O3 function.
[UART3 Control Register (UART3CON)]
003316
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer, and one bit (bit 4) which is al-
ways valid and sets the output structure of the P35/TXD3 pin.
[Serial I/O3 Status Register (SIO3STS)] 003116
The read-only serial I/O3 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O3
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer register is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer reg-
ister, and the receive buffer full flag is set. A write to the serial I/O3
status register clears all the error flags OE, PE, FE, and SE (bit 3
to bit 6, respectively). Writing “0” to the serial I/O3 enable bit SIOE
(bit 7 of the serial I/O3 control register) also clears all the status
flags, including the error flags.
Bits 0 to 6 of the serial I/O3 status register are initialized to “0” at
reset, but if the transmit enable bit (bit 4) of the serial I/O3 control
register has been set to “1”, the transmit shift completion flag (bit
2) and the transmit buffer empty flag (bit 0) become “1”.
[Transmit Buffer Register 3/Receive Buffer
Register 3 (TB3/RB3)] 003016
The transmit buffer register 3 and the receive buffer register 3 are
located at the same address. The transmit buffer is write-only and
the receive buffer is read-only. If a character bit length is 7 bits, the
MSB of data stored in the receive buffer is “0”.
[Baud Rate Generator 3 (BRG3)] 002F16
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
Rev.1.01 Jan 25, 2005 page 49 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
b0
b7
Serial I/O3 status register
(SIO3STS : address 003116
Serial I/O3 control register
(SIO3CON : address 003216
)
)
BRG count source selection bit (CSS)
0: f(XIN) (f(XCIN) in low-speed mode)
1: f(XIN)/4 (f(XCIN)/4 in low-speed mode)
Transmit buffer empty flag (TBE)
0: Buffer full
1: Buffer empty
Serial I/O3 synchronous clock selection bit (SCS)
0: BRG output divided by 4 when clock synchronous
serial I/O is selected, BRG output divided by 16
when UART is selected.
Receive buffer full flag (RBF)
0: Buffer empty
1: Buffer full
1: External clock input when clock synchronous serial
I/O is selected, external clock input divided by 16
when UART is selected.
Transmit shift completion flag (TSC)
0: Transmit shift in progress
1: Transmit shift completed
S
0: P3
1: P3
RDY3 output enable bit (SRDY)
Overrun error flag (OE)
0: No error
1: Overrun error
7
pin operates as normal I/O pin
pin operates as SRDY3 output pin
7
Transmit interrupt source selection bit (TIC)
0: Interrupt when transmit buffer has emptied
1: Interrupt when transmit shift operation is completed
Parity error flag (PE)
0: No error
1: Parity error
Transmit enable bit (TE)
0: Transmit disabled
1: Transmit enabled
Framing error flag (FE)
0: No error
1: Framing error
Receive enable bit (RE)
0: Receive disabled
1: Receive enabled
Summing error flag (SE)
0: (OE) U (PE) U (FE)=0
1: (OE) U (PE) U (FE)=1
Serial I/O3 mode selection bit (SIOM)
0: Clock asynchronous (UART) serial I/O
1: Clock synchronous serial I/O
Not used (returns “1” when read)
Serial I/O3 enable bit (SIOE)
0: Serial I/O disabled
(pins P3
1: Serial I/O enabled
(pins P3 to P3 operate as serial I/O pins)
4 to P37 operate as normal I/O pins)
4
7
b7
b0
UART3 control register
(UART3CON : address 003316
)
Character length selection bit (CHAS)
0: 8 bits
1: 7 bits
Parity enable bit (PARE)
0: Parity checking disabled
1: Parity checking enabled
Parity selection bit (PARS)
0: Even parity
1: Odd parity
Stop bit length selection bit (STPS)
0: 1 stop bit
1: 2 stop bits
P35/TXD3 P-channel output disable bit (POFF)
0: CMOS output (in output mode)
1: N-channel open drain output (in output mode)
Not used (return “1” when read)
Fig. 44 Structure of serial I/O3 control registers
Rev.1.01 Jan 25, 2005 page 50 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀ Notes concerning serial I/O3
1. Notes when selecting clock synchronous serial I/O
1.1 Stop of transmission operation
2. Notes when selecting clock asynchronous serial I/O
2.1 Stop of transmission operation
ꢀ Note
ꢀ Note
Clear the transmit enable bit to “0” (transmit disabled). The trans-
mission operation does not stop by clearing the serial I/O3 enable
bit to “0”.
Clear the serial I/O3 enable bit and the transmit enable bit to “0”
(serial I/O and transmit disabled).
ꢀ Reason
ꢀ Reason
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O3 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD3 pin and an operation failure occurs.
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O3 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O3 enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD3 pin and an operation failure occurs.
1.2 Stop of receive operation
2.2 Stop of receive operation
ꢀ Note
ꢀ Note
Clear the receive enable bit to “0” (receive disabled), or clear the
serial I/O3 enable bit to “0” (serial I/O disabled).
Clear the receive enable bit to “0” (receive disabled).
2.3 Stop of transmit/receive operation
1.3 Stop of transmit/receive operation
ꢀ Note
ꢀ Note 1 (only transmission operation is stopped)
Clear the transmit enable bit to “0” (transmit disabled). The trans-
mission operation does not stop by clearing the serial I/O3 enable
bit to “0”.
Clear both the transmit enable bit and receive enable bit to “0”
(transmit and receive disabled).
(when data is transmitted and received in the clock synchronous
serial I/O mode, any one of data transmission and reception can-
not be stopped.)
ꢀ Reason
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O3 enable bit is cleared to “0”
(serial I/O disabled), the internal transmission is running (in this
case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O
ports, the transmission data is not output). When data is written to
the transmit buffer register in this state, data starts to be shifted to
the transmit shift register. When the serial I/O3 enable bit is set to
“1” at this time, the data during internally shifting is output to the
TxD3 pin and an operation failure occurs.
ꢀ Reason
In the clock synchronous serial I/O mode, the same clock is used
for transmission and reception. If any one of transmission and re-
ception is disabled, a bit error occurs because transmission and
reception cannot be synchronized.
In this mode, the clock circuit of the transmission circuit also oper-
ates for data reception. Accordingly, the transmission circuit does
not stop by clearing only the transmit enable bit to “0” (transmit
disabled). Also, the transmission circuit is not initialized by clear-
ing the serial I/O3 enable bit to “0” (serial I/O disabled) (refer to
1.1).
ꢀ Note 2 (only receive operation is stopped)
Clear the receive enable bit to “0” (receive disabled).
Rev.1.01 Jan 25, 2005 page 51 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
3. SRDY3 output of reception side
7. Transmit interrupt request when transmit enable bit is set
ꢀ Note
ꢀ Note
When signals are output from the SRDY3 pin on the reception side
by using an external clock in the clock synchronous serial I/O
mode, set all of the receive enable bit, the SRDY3 output enable
bit, and the transmit enable bit to “1” (transmit enabled).
When using the transmit interrupt, take the following sequence.
ꢀ Set the serial I/O3 transmit interrupt enable bit to “0” (disabled).
ꢀ Set the transmit enable bit to “1”.
ꢀ Set the serial I/O3 transmit interrupt request bit to “0” after 1 or
more instruction has executed.
4. Setting serial I/O3 control register again
ꢀ Note
ꢀ Set the serial I/O3 transmit interrupt enable bit to “1” (enabled).
ꢀ Reason
Set the serial I/O3 control register again after the transmission and
the reception circuits are reset by clearing both the transmit en-
able bit and the receive enable bit to “0.”
When the transmit enable bit is set to “1”, the transmit buffer
empty flag and the transmit shift register shift completion flag are
also set to “1”. Therefore, regardless of selecting which timing for
the generating of transmit interrupts, the interrupt request is gener-
ated and the transmit interrupt request bit is set at this point.
Clear both the transmit enable bit
(TE) and the receive enable bit
(RE) to “0”
↓
Set the bits 0 to 3 and bit 6 of the
serial I/O3 control register
Can be set with the
↓
LDM instruction at the
same time
Set both the transmit enable bit
(TE) and the receive enable bit
(RE), or one of them to “1”
5. Data transmission control with referring to transmit shift
register completion flag
ꢀ Note
After the transmit data is written to the transmit buffer register, the
transmit shift register completion flag changes from “1” to “0” with
a delay of 0.5 to 1.5 shift clocks. When data transmission is con-
trolled with referring to the flag after writing the data to the transmit
buffer register, note the delay.
6. Transmission control when external clock is selected
ꢀ Note
When an external clock is used as the synchronous clock for data
transmission, set the transmit enable bit to “1” at “H” of the SCLK3
input level. Also, write data to the transmit buffer register at “H” of
the SCLK input level.
Rev.1.01 Jan 25, 2005 page 52 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
PULSE WIDTH MODULATION (PWM)
The 3804 group (Spec. H) has PWM functions with an 8-bit reso-
lution, based on a signal that is the clock input XIN or that clock
input divided by 2 or the clock input XCIN or that clock input di-
vided by 2 in low-speed mode.
PWM Operation
When bit 0 (PWM enable bit) of the PWM control register is set to
“1”, operation starts by initializing the PWM output circuit, and
pulses are output starting at an “H”.
If the PWM register or PWM prescaler is updated during PWM
output, the pulses will change in the cycle after the one in which
the change was made.
Data Setting
The PWM output pin also functions as port P56. Set the PWM pe-
riod by the PWM prescaler, and set the “H” term of output pulse by
the PWM register.
31.875 ꢀ m ꢀ(n+1)
µs
If the value in the PWM prescaler is n and the value in the PWM
register is m (where n = 0 to 255 and m = 0 to 255) :
PWM period = 255 ꢀ (n+1) / f(XIN)
255
PWM output
= 31.875 ꢀ (n+1) µs (when f(XIN) = 8 MHz)
Output pulse “H” term = PWM period ꢀ m / 255
= 0.125 ꢀ (n+1) ꢀ m µs
T = [31.875 ꢀ (n+1)] µs
(when f(XIN) = 8 MHz)
m: Contents of PWM register
n : Contents of PWM prescaler
T : PWM period (when f(XIN) = 8 MHz
Fig. 45 Timing of PWM period
Data bus
PWM
prescaler pre-latch
PWM
register pre-latch
Transfer control circuit
PWM
prescaler latch
PWM
register latch
Count source
selection bit
Port P5
6
“0”
X
IN
or
CIN
PWM register
PWM prescaler
X
“1”
1/2
Port P56 latch
PWM enable bit
Fig. 46 Block diagram of PWM function
Rev.1.01 Jan 25, 2005 page 53 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
PWM control register
(PWMCON : address 002B16
)
PWM function enable bit
0: PWM disabled
1: PWM enabled
Count source selection bit
0: f(XIN
)
1: f(XIN)/2
Not used (return “0” when read)
Fig. 47 Structure of PWM control register
B
T
C
T2
=
A
B
C
PWM output
T
T2
T
PWM register
write signal
(Changes “H” term from “A” to “B”.)
PWM prescaler
write signal
(Changes PWM period from “T” to “T2”.)
When the contents of the PWM register or PWM prescaler have changed, the PWM
output will change from the next period after the change.
Fig. 48 PWM output timing when PWM register or PWM prescaler is changed
Rev.1.01 Jan 25, 2005 page 54 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
A/D CONVERTER
[AD Conversion Register 1, 2 (AD1, AD2)]
003516, 003816
Channel Selector
The channel selector selects one of ports P67/AN7 to P60/AN0 or
P07/AN15 to P00/AN8, and inputs the voltage to the comparator.
The AD conversion register is a read-only register that stores the
result of an A/D conversion. When reading this register during an
A/D conversion, the previous conversion result is read.
Bit 7 of the AD conversion register 2 is the conversion mode se-
lection bit. When this bit is set to “0,” the A/D converter becomes
the 10-bit A/D mode. When this bit is set to “1,” that becomes the
8-bit A/D mode. The conversion result of the 8-bit A/D mode is
stored in the AD conversion register 1. As for 10-bit A/D mode, not
only 10-bit reading but also only high-order 8-bit reading of con-
version result can be performed by selecting the reading
procedure of the AD conversion registers 1, 2 after A/D conversion
is completed (in Figure 50).
Comparator and Control Circuit
The comparator and control circuit compares an analog input volt-
age with the comparison voltage, and then stores the result in the
AD conversion registers 1, 2. When an A/D conversion is com-
pleted, the control circuit sets the AD conversion completion bit
and the AD interrupt request bit to “1”.
Note that because the comparator consists of a capacitor cou-
pling, set f(XIN) to 500 kHz or more during an A/D conversion.
b7
b0
AD/DA control register
(ADCON : address 003416
As for 10-bit A/D mode, the 8-bit reading inclined to MSB is per-
formed when reading the AD converter register 1 after A/D
conversion is started; and when the AD converter register 1 is
read after reading the AD converter register 2, the 8-bit reading in-
clined to LSB is performed.
)
Analog input pin selection bits 1
b2 b1 b0
0 0 0: P6
0 0 1: P6
0 1 0: P6
0 1 1: P6
1 0 0: P6
1 0 1: P6
1 1 0: P6
1 1 1: P6
0
1
2
3
4
5
6
7
/AN
/AN
/AN
/AN
/AN
/AN
/AN
/AN
0
1
2
3
4
5
6
7
or P0
or P0
or P0
or P0
or P0
or P0
or P0
or P0
0
1
2
3
4
5
6
7
/AN
/AN
8
9
/AN10
/AN11
/AN12
/AN13
/AN14
/AN15
[AD/DA Control Register (ADCON)] 003416
The AD/DA control register controls the A/D conversion process.
Bits 0 to 2 and bit 4 select a specific analog input pin. Bit 3 signals
the completion of an A/D conversion. The value of this bit remains
at “0” during an A/D conversion, and changes to “1” when an A/D
conversion ends. Writing “0” to this bit starts the A/D conversion.
AD conversion completion bit
0: Conversion in progress
1: Conversion completed
Analog input pin selection bit 2
0: AN
1: AN
0
to AN
to AN15 side
7 side
8
Comparison Voltage Generator
The comparison voltage generator divides the voltage between
VREF and AVSS into 1024, and that outputs the comparison voltage
in the 10-bit A/D mode (256 division in 8-bit A/D mode).
The A/D converter successively compares the comparison voltage
Vref in each mode, dividing the VREF voltage (see below), with the
input voltage.
Not used (returns “0” when read)
DA
1
output enable bit
0: DA
1
output disabled
output enabled
1: DA
1
DA
2
output enable bit
0: DA
2
output disabled
output enabled
1: DA
2
• 10-bit A/D mode (10-bit reading)
VREF
Vref =ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀn (n = 0–1023)
Fig. 49 Structure of AD/DA control register
1024
• 10-bit A/D mode (8-bit reading)
VREF
Vref =ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀn (n = 0–255)
10-bit reading
256
(Read address 003816 before 003516
)
• 8-bit A/D mode
b0
b9 b8
b0
b7
VREF
Vref =ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ(n–0.5) (n = 1–255)
AD conversion register 2
256
0
(AD2: address 003816
)
=0
(n = 0)
b7
AD conversion register 1
(AD1: address 003516
b7 b6 b5 b4 b3 b2 b1 b0
)
Note : Bits 2 to 6 of address 003816 become “0”
at reading.
8-bit reading
(Read only address 003516
AD conversion register 1
)
b7
b9 b8 b7 b6 b5 b4 b3 b2
b0
(AD1: address 003516
)
Fig. 50 Structure of 10-bit A/D mode reading
Rev.1.01 Jan 25, 2005 page 55 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Data bus
b7
4
b0
AD/DA control register
(Address 003416
)
AD converter interrupt request
A/D control circuit
P6
P6
0
/AN
0
1
/AN
1
P6
P6
2
3
/AN
/AN
2
3
(Address 003816
(Address 003516
)
)
AD conversion register 2
AD conversion register 1
Comparator
P6
P6
P6
4
/AN
/AN
/AN
4
10
5
5
6
6
Resistor ladder
P6
P0
P0
7
0
1
/AN
/AN
/AN
7
8
9
P0
P0
P0
2
/AN10
/AN11
/AN12
3
V
REF AVSS
4
P0
P0
P0
5/AN13
6/AN14
7/AN15
Fig. 51 Block diagram of A/D converter
Rev.1.01 Jan 25, 2005 page 56 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
D/A CONVERTER
The 3804 group (Spec. H) has two internal D/A converters (DA1
and DA2) with 8-bit resolution.
The D/A conversion is performed by setting the value in each DA
conversion register. The result of D/A conversion is output from
the DA1 or DA2 pin by setting the DA output enable bit to “1”.
When using the D/A converter, the corresponding port direction
register bit (P30/DA1 or P31/DA2) must be set to “0” (input status).
The output analog voltage V is determined by the value n (decimal
notation) in the DA conversion register as follows:
DA1 conversion register (8)
DA
1
output enable bit
P3 /DA
R-2R resistor ladder
0
1
V = VREF ꢀ n/256 (n = 0 to 255)
Where VREF is the reference voltage.
DA2 conversion register (8)
DA
At reset, the DA conversion registers are cleared to “0016”, and
the DA output enable bits are cleared to “0”, and the P30/DA1 and
P31/DA2 pins become high impedance.
2
output enable bit
P3 /DA
R-2R resistor ladder
1
2
The DA output does not have buffers. Accordingly, connect an ex-
ternal buffer when driving a low-impedance load.
Fig. 52 Block diagram of D/A converter
DA1
output enable bit
R
“0”
R
2R
R
R
R
R
R
P30/DA1
“1”
2R
2R
2R
2R
2R
2R
2R
2R
LSB
MSB
DA1 conversion register
“0”
“1”
AVSS
VREF
Fig. 53 Equivalent connection circuit of D/A converter (DA1)
Rev.1.01 Jan 25, 2005 page 57 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
WATCHDOG TIMER
When bit 6 of the watchdog timer control register is kept at “0”, the
STP instruction is enabled. When that is executed, both the clock
and the watchdog timer stop. Count re-starts at the same time as
the release of stop mode (Note). The watchdog timer does not
stop while a WIT instruction is executed. In addition, the STP in-
struction is disabled by writing “1” to this bit again. When the STP
instruction is executed at this time, it is processed as an undefined
instruction, and an internal reset occurs. Once a “1” is written to
this bit, it cannot be programmed to “0” again.
The watchdog timer gives a mean of returning to the reset status
when a program cannot run on a normal loop (for example, be-
cause of a software run-away). The watchdog timer consists of an
8-bit watchdog timer L and an 8-bit watchdog timer H.
Watchdog Timer Initial Value
Watchdog timer L is set to “FF16” and watchdog timer H is set to
“FF16” by writing to the watchdog timer control register (address
001E16) or at a reset. Any write instruction that causes a write sig-
nal can be used, such as the STA, LDM, CLB, etc. Data can only
be written to bits 6 and 7 of the watchdog timer control register.
Regardless of the value written to bits 0 to 5, the above-mentioned
value will be set to each timer.
The following shows the period between the write execution to the
watchdog timer control register and the underflow of watchdog
timer H.
Bit 7 of the watchdog timer control register is “0”:
when XCIN = 32.768 kHz; 32 s
Watchdog Timer Operations
when XIN = 16 MHz; 65.536 ms
The watchdog timer stops at reset and a countdown is started by
the writing to the watchdog timer control register. An internal reset
occurs when watchdog timer H underflows. The reset is released
after its release time. After the release, the program is restarted
from the reset vector address. Usually, write to the watchdog timer
control register by software before an underflow of the watchdog
timer H. The watchdog timer does not function if the watchdog
timer control register is not written to at least once.
Bit 7 of the watchdog timer control register is “1”:
when XCIN = 32.768 kHz; 125 ms
when XIN = 16 MHz; 256 µs
Note: The watchdog timer continues to count even while waiting for a stop
release. Therefore, make sure that watchdog timer H does not un-
derflow during this period.
“FF16” is set when
Data bus
watchdog timer
control register is
written to.
“FF16” is set when
watchdog timer
control register is
written to.
X
CIN
“0”
“1”
“10”
Watchdog timer L (8)
Main clock division
ratio selection bits
(Note)
Watchdog timer H (8)
1/16
“00”
“01”
Watchdog timer H count
source selection bit
X
IN
STP instruction disable bit
STP instruction
Reset
circuit
Internal reset
RESET
Reset release time waiting
Note: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
Fig. 54 Block diagram of Watchdog timer
b0
b7
Watchdog timer control register
(WDTCON : address 001E16
)
Watchdog timer H (for read-out of high-order 6 bit)
STP instruction disable bit
0: STP instruction enabled
1: STP instruction disabled
Watchdog timer H count source selection bit
0: Watchdog timer L underflow
1: f(XIN)/16 or f(XCIN)/16
Fig. 55 Structure of Watchdog timer control register
Rev.1.01 Jan 25, 2005 page 58 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
2
MULTI-MASTER I C-BUS INTERFACE
Table 7 Multi-master I C-BUS interface functions
2
The 3804 group (Spec. H) has the multi-master I C-BUS interface.
Item
Function
2
The multi-master I C-BUS interface is a serial communications cir-
2
In conformity with Philips I C-BUS
standard:
2
cuit, conforming to the Philips I C-BUS data transfer format. This
10-bit addressing format
7-bit addressing format
High-speed clock mode
Standard clock mode
interface, offering both arbitration lost detection and a synchro-
nous functions, is useful for the multi-master serial
communications.
Format
2
2
Figure 56 shows a block diagram of the multi-master I C-BUS in-
In conformity with Philips I C-BUS
standard:
2
terface and Table 7 lists the multi-master I C-BUS interface
Master transmission
Master reception
Slave transmission
Slave reception
functions.
Communication mode
SCL clock frequency
2
2
This multi-master I C-BUS interface consists of the I C slave ad-
2
2
dress registers 0 to 2, the I C data shift register, the I C clock
2
2
control register, the I C control register, the I C status register, the
16.1 kHz to 400 kHz (at φ= 4 MHz)
2
2
I C START/STOP condition control register, the I C special mode
System clock φ = f(XIN)/2 (high-speed mode)
φ = f(XIN)/8 (middle-speed mode)
2
control register, the I C special mode status register, and other
control circuits.
2
When using the multi-master I C-BUS interface, set 1 MHz or
more to the internal clock φ.
Interrupt
generating
circuit
Interrupt request signal
2
b7
b0
I C slave address registers 0 to 2
(SCL, SDA, IRQ)
Interrupt
generating
circuit
Interrupt request signal
(I2CIRQ)
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1SAD0 RWB
S0D0–2
Address comparator
I2C data shift register
Noise
elimination
circuit
Data
control
circuit
Serial data
(SDA)
b7
b0
b7
b0
S
0
AL AAS AD0 LRB
MST TRX BB PIN
S1
AL
circuit
SSC4 SSC3 SSC2 SSC1 SSC0
SIS SIP
I2C status register
2
I
C START/STOP condition control
S2D
register
Internal data bus
BB
circuit
Noise
elimination
circuit
Clock
control
circuit
Serial
clock
(SCL)
b7
ACK
S2
b0
b7
b0
ACK
BIT
FAST
MODE
CCR4 CCR3 CCR2 CCR1 CCR0
SPCF
PIN2
AAS2 AAS1 AAS0
I2C clock control register
I2C special mode status register
S3
Clock division
System clock (φ)
b7
b0
b7
b0
PIN2 PIN2
ACKI
HSLAD
CON
SPCFL
HD
IN
10BIT
SAD
TISS TSEL
ALS
BC2 BC1
ES0 BC0
I2 C special mode control register
S3D
S1D I2C control register
Bit counter
2
Fig. 56 Block diagram of multi-master I C-BUS interface
ꢀꢀ: Purchase of MITSUBISHI ELECTRIC CORPORATIONS I2C components conveys a license under the Philips I2C Patent Rights to use these components
an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
Rev.1.01 Jan 25, 2005 page 59 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C Data Shift Register (S0)] 001116
b7
b0
2
I2C slave address register 0
The I C data shift register (S0: address 001116) is an 8-bit shift
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1SAD0 RWB
(S0D0: address 0FF716
I2C slave address register 1
(S0D1: address 0FF816
I2C slave address register 2
)
register to store receive data and write transmit data.
When transmit data is written into this register, it is transferred to
the outside from bit 7 in synchronization with the SCL, and each
time one-bit data is output, the data of this register are shifted by
one bit to the left. When data is received, it is input to this register
from bit 0 in synchronization with the SCL, and each time one-bit
data is input, the data of this register are shifted by one bit to the
left. The minimum 2 cycles of the internal clock φ are required
from the rising of the SCL until input to this register.
)
(S0D2: address 0FF916
)
Read/write bit
Slave address
2
2
Fig. 57 Structure of I C slave address registers 0 to 2
The I C data shift register is in a write enable status only when the
2
2
I C-BUS interface enable bit (ES0 bit) of the I C control register
(S1D: address 001416) is “1”. The bit counter is reset by a write in-
2
struction to the I C data shift register. When both the ES0 bit and
2
the MST bit of the I C status register (S1: address 001316) are “1,”
2
the SCL is output by a write instruction to the I C data shift regis-
2
ter. Reading data from the I C data shift register is always enabled
regardless of the ES0 bit value.
2
[I CSlaveAddressRegisters0to2(S0D0toS0D2)]
0FF716 to 0FF916
2
The I C slave address registers 0 to 2 (S0D0 to S0D2: addresses
0FF716 to 0FF916) consists of a 7-bit slave address and a read/
write bit. In the addressing mode, the slave address written in this
register is compared with the address data to be received immedi-
ately after the START condition is detected.
•Bit 0: Read/write bit (RWB)
This is not used in the 7-bit addressing mode. In the 10-bit ad-
dressing mode, set RWB to “0” because the first address data to
be received is compared with the contents (SAD6 to SAD0 +
2
RWB) of the I C slave address registers 0 to 2.
When 2-byte address data match slave address, a 7-bit slave ad-
dress which is received after restart condition has detected and
R/W data can be matched by setting “1” to RWB with software.
The RWB is cleared to “0” automatically when the stop condition is
detected.
•Bits 1 to 7: Slave address (SAD0–SAD6)
These bits store slave addresses. Regardless of the 7-bit address-
ing mode or the 10-bit addressing mode, the address data
transmitted from the master is compared with these bits’ contents.
Rev.1.01 Jan 25, 2005 page 60 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C Clock Control Register (S2)] 001516
b7
b0
2
The I C clock control register (S2: address 001516) is used to set
I2C clock control register
(S2 : address 001516
ACK FAST
BIT MODE
ACK
CCR4 CCR3 CCR2 CCR1 CCR0
)
ACK control, SCL mode and SCL frequency.
•Bits 0 to 4: SCL frequency control bits (CCR0–CCR4)
These bits control the SCL frequency. Refer to Table 8.
•Bit 5: SCL mode specification bit (FAST MODE)
This bit specifies the SCL mode. When this bit is set to “0,” the
standard clock mode is selected. When the bit is set to “1,” the
high-speed clock mode is selected.
SCL frequency control bits
Refer to Table 8.
SCL mode specification bit
0 : Standard clock mode
1 : High-speed clock mode
ACK bit
2
When connecting the bus of the high-speed mode I C bus stan-
0 : ACK is returned.
1 : ACK is not returned.
dard (maximum 400 kbits/s), use 8 MHz or more oscillation
frequency f(XIN) in the high-speed mode (2 division clock).
•Bit 6: ACK bit (ACK BIT)
ACK clock bit
0 : No ACK clock
1 : ACK clock
ꢀ
This bit sets the SDA status when an ACK clock is generated.
When this bit is set to “0,” the ACK return mode is selected and
SDA goes to “L” at the occurrence of an ACK clock. When the bit
is set to “1,” the ACK non-return mode is selected. The SDA is
held in the “H” status at the occurrence of an ACK clock.
2
Fig. 58 Structure of I C clock control register
2
Table 8 Set values of I C clock control register and SCL
However, when the slave address agree with the address data in
the reception of address data at ACK BIT = “0,” the SDA is auto-
matically made “L” (ACK is returned). If there is a disagreement
between the slave address and the address data, the SDA is auto-
matically made “H” (ACK is not returned).
frequency
Setting value of
SCL frequency
CCR4–CCR0
(at φ = 4 MHz, unit : kHz) (Note 1)
Standard clock
mode
High-speed clock
mode
CCR4 CCR3 CCR2 CCR1 CCR0
Setting disabled Setting disabled
Setting disabled Setting disabled
Setting disabled Setting disabled
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
ꢀACK clock: Clock for acknowledgment
•Bit 7: ACK clock bit (ACK)
This bit specifies the mode of acknowledgment which is an ac-
knowledgment response of data transfer. When this bit is set to
“0,” the no ACK clock mode is selected. In this case, no ACK clock
occurs after data transmission. When the bit is set to “1,” the ACK
clock mode is selected and the master generates an ACK clock
each completion of each 1-byte data transfer. The device for
transmitting address data and control data releases the SDA at
the occurrence of an ACK clock (makes SDA “H”) and receives the
ACK bit generated by the data receiving device.
– (Note 2)
– (Note 2)
100
333
250
400 (Note 3)
166
83.3
500/CCR value 1000/CCR value
(Note 3)
(Note 3)
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
34.5
17.2
33.3
16.6
32.3
16.1
Note: Do not write data into the I2C clock control register during transfer. If
data is written during transfer, the I2C clock generator is reset, so
that data cannot be transferred normally.
Notes 1: Duty of SCL output is 50 %. The duty becomes 35 to 45 % only
when the high-speed clock mode is selected and CCR value = 5
(400 kHz, at φ = 4 MHz). “H” duration of the clock fluctuates from
–4 to +2 machine cycles in the standard clock mode, and fluctu-
ates from –2 to +2 machine cycles in the high-speed clock mode.
In the case of negative fluctuation, the frequency does not in-
crease because “L” duration is extended instead of “H” duration
reduction.
These are values when SCL synchronization by the synchronous
function is not performed. CCR value is the decimal notation
value of the SCL frequency control bits CCR4 to CCR0.
2: Each value of SCL frequency exceeds the limit at φ = 4 MHz or
more. When using these setting value, use φ of 4 MHz or less.
3: The data formula of SCL frequency is described below:
φ/(8 ꢀ CCR value) Standard clock mode
φ/(4 ꢀ CCR value) High-speed clock mode (CCR value ≠ 5)
φ/(2 ꢀ CCR value) High-speed clock mode (CCR value = 5)
Do not set 0 to 2 as CCR value regardless of φ frequency.
Set 100 kHz (max.) in the standard clock mode and 400 kHz
(max.) in the high-speed clock mode to the SCL frequency by
setting the SCL frequency control bits CCR4 to CCR0.
Rev.1.01 Jan 25, 2005 page 61 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C Control Register (S1D)] 001416
b7
b0
2
I2C control register
The I C control register (S1D: address 001416) controls data com-
10 BIT
SAD
ALS ES0 BC2 BC1 BC0
TISS
(S1D : address 001416
)
munication format.
•Bits 0 to 2: Bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
Bit counter (Number of
transmit/receive bits)
b2 b1 b0
2
transmitted. The I C interrupt request signal occurs immediately
after the number of count specified with these bits (ACK clock is
added to the number of count when ACK clock is selected by ACK
clock bit (bit 7 of S2, address 001516) have been transferred, and
BC0 to BC2 are returned to “0002”.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0 : 8
1 : 7
0 : 6
1 : 5
0 : 4
1 : 3
0 : 2
1 : 1
Also when a START condition is received, these bits become
“0002” and the address data is always transmitted and received in
8 bits.
I2C-BUS interface
enable bit
0 : Disabled
1 : Enabled
2
•Bit 3: I C interface enable bit (ES0)
2
This bit enables to use the multi-master I C-BUS interface. When
this bit is set to “0,” the use disable status is provided, so that the
SDA and the SCL become high-impedance. When the bit is set to
“1,” use of the interface is enabled.
Data format selection bit
0 : Addressing format
1 : Free data format
When ES0 = “0,” the following is performed.
2
• PIN = “1,” BB = “0” and AL = “0” are set (which are bits of the I C
Addressing format
selection bit
0 : 7-bit addressing
format
1 : 10-bit addressing
format
status register, S1, at address 001316 ).
2
• Writing data to the I C data shift register (S0: address 001116) is
disabled.
•Bit 4: Data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses.
When this bit is set to “0,” the addressing format is selected, so
that address data is recognized. When a match is found between
a slave address and address data as a result of comparison or
Not used
(return “0” when read)
I2C-BUS interface pin input
level selection bit
2
when a general call (refer to “I C Status Register,” bit 1) is re-
0 : CMOS input
1 : SMBUS input
ceived, transfer processing can be performed. When this bit is set
to “1,” the free data format is selected, so that slave addresses are
not recognized.
2
Fig. 59 Structure of I C control register
•Bit 5: Addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit
is set to “0,” the 7-bit addressing format is selected. In this case,
2
only the high-order 7 bits (slave address) of the I C slave address
registers 0 to 2 are compared with address data. When this bit is
set to “1,” the 10-bit addressing format is selected, and all the bits
2
of the I C slave address registers 0 to 2 are compared with ad-
dress data.
2
•Bit 7: I C-BUS interface pin input level selection bit (TISS)
This bit selects the input level of the SCL and SDA pins of the
2
multi-master I C-BUS interface.
Rev.1.01 Jan 25, 2005 page 62 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C Status Register (S1)] 001316
•Bit 4: SCL pin low hold bit (PIN)
2
2
The I C status register (S1: address 001316) controls the I C-BUS
interface status. The low-order 4 bits are read-only bits and the
high-order 4 bits can be read out and written to.
This bit generates an interrupt request signal. Each time 1-byte
data is transmitted, the PIN bit changes from “1” to “0.” At the
same time, an interrupt request signal occurs to the CPU. The PIN
bit is set to “0” in synchronization with a falling of the last clock (in-
cluding the ACK clock) of an internal clock and an interrupt
request signal occurs in synchronization with a falling of the PIN
bit. When the PIN bit is “0,” the SCL is kept in the “0” state and
clock generation is disabled. Figure 61 shows an interrupt request
signal generating timing chart.
Set “00002” to the low-order 4 bits, because these bits become the
reserved bits at writing.
•Bit 0: Last receive bit (LRB)
This bit stores the last bit value of received data and can also be
used for ACK receive confirmation. If ACK is returned when an
ACK clock occurs, the LRB bit is set to “0.” If ACK is not returned,
this bit is set to “1.” Except in the ACK mode, the last bit value of
received data is input. The state of this bit is changed from “1” to
The PIN bit is set to “1” in one of the following conditions:
2
• Executing a write instruction to the I C data shift register (S0:
2
“0” by executing a write instruction to the I C data shift register
address 001116). (This is the only condition which the prohibition
of the internal clock is released and data can be communicated
except for the start condition detection.)
(S0: address 001116).
•Bit 1: General call detecting flag (AD0)
ꢀ
When the ALS bit is “0”, this bit is set to “1” when a general call
whose address data is all “0” is received in the slave mode. By a
general call of the master device, every slave device receives con-
trol data after the general call. The AD0 bit is set to “0” by
detecting the STOP condition or START condition, or reset.
• When the ES0 bit is “0”
• At reset
• When writing “1” to the PIN bit by software
The PIN bit is set to “0” in one of the following conditions:
• Immediately after completion of 1-byte data transmission (includ-
ing when arbitration lost is detected)
ꢀGeneral call: The master transmits the general call address “0016” to all
• Immediately after completion of 1-byte data reception
• In the slave reception mode, with ALS = “0” and immediately af-
ter completion of slave address agreement or general call
address reception
slaves.
•Bit 2: Slave address comparison flag (AAS)
This flag indicates a comparison result of address data when the
ALS bit is “0”.
• In the slave reception mode, with ALS = “1” and immediately af-
ter completion of address data reception
ꢀ In the slave receive mode, when the 7-bit addressing format is
selected, this bit is set to “1” in one of the following conditions:
• The address data immediately after occurrence of a START
condition agrees with the slave address stored in the high-or-
•Bit 5: Bus busy flag (BB)
This bit indicates the status of use of the bus system. When this
bit is set to “0,” this bus system is not busy and a START condition
can be generated. The BB flag is set/reset by the SCL, SDA pins
input signal regardless of master/slave. This flag is set to “1” by
detecting the START condition, and is set to “0” by detecting the
STOP condition. The condition of these detecting is set by the
2
der 7 bits of the I C slave address register.
• A general call is received.
ꢀ In the slave receive mode, when the 10-bit addressing format is
selected, this bit is set to “1” with the following condition:
2
• When the address data is compared with the I C slave ad-
2
START/STOP condition setting bits (SSC4–SSC0) of the I C
dress register (8 bits consisting of slave address and RWB
bit), the first bytes agree.
START/STOP condition control register (S2D: address 001616).
2
When the ES0 bit of the I C control register (bit 3 of S1D, address
2
ꢀꢀThis bit is set to “0” by executing a write instruction to the I C data
001416) is “0” or reset, the BB flag is set to “0.”
shift register (S0: address 001116) when ES0 is set to “1” or reset.
For the writing function to the BB flag, refer to the sections
“START Condition Generating Method” and “STOP Condition Gen-
erating Method” described later.
ꢀ
•Bit 3: Arbitration lost detecting flag (AL)
In the master transmission mode, when the SDA is made “L” by
any other device, arbitration is judged to have been lost, so that
this bit is set to “1.” At the same time, the TRX bit is set to “0,” so
that immediately after transmission of the byte whose arbitration
was lost is completed, the MST bit is set to “0.” The arbitration lost
can be detected only in the master transmission mode. When ar-
bitration is lost during slave address transmission, the TRX bit is
set to “0” and the reception mode is set. Consequently, it becomes
possible to detect the agreement of its own slave address and ad-
dress data transmitted by another master device.
The AL bit is set to “0” in one of the following conditions:
2
•Executing a write instruction to the I C data shift register (S0: ad-
dress 001116)
•When the ES0 bit is “0”
•At reset
ꢀArbitration lost :The status in which communication as a master is dis-
abled.
Rev.1.01 Jan 25, 2005 page 63 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
•Bit 6: Communication mode specification bit (transfer direc-
tion specification bit: TRX)
b7
b0
I2C status register
(S1 : address 001316
MST TRX BB PIN AL AAS AD0 LRB
This bit decides a direction of transfer for data communication.
When this bit is “0,” the reception mode is selected and the data of
a transmitting device is received. When the bit is “1,” the transmis-
sion mode is selected and address data and control data are
output onto the SDA in synchronization with the clock generated
on the SCL.
)
Last receive bit (Note)
0 : Last bit = “0”
1 : Last bit = “1”
General call detecting flag
(Note)
0 : No general call detected
1 : General call detected
This bit is set/reset by software and hardware. About set/reset by
hardware is described below. This bit is set to “1” by hardware
when all the following conditions are satisfied:
• When ALS is “0”
Slave address comparison flag
(Note)
0 : Address disagreement
1 : Address agreement
• In the slave reception mode or the slave transmission mode
• When the R/W bit reception is “1”
This bit is set to “0” in one of the following conditions:
• When arbitration lost is detected.
Arbitration lost detecting flag
(Note)
• When a STOP condition is detected.
0 : Not detected
1 : Detected
• When writing “1” to this bit by software is invalid by the START
condition duplication preventing function (Note).
• With MST = “0” and when a START condition is detected.
• With MST = “0” and when ACK non-return is detected.
• At reset
SCL pin low hold bit
0 : SCL pin low hold
1 : SCL pin low release
•Bit 7: Communication mode specification bit (master/slave
specification bit: MST)
Bus busy flag
0 : Bus free
1 : Bus busy
This bit is used for master/slave specification for data communica-
tion. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are re-
ceived, and data communication is performed in synchronization
with the clock generated by the master. When this bit is “1,” the
master is specified and a START condition and a STOP condition
are generated. Additionally, the clocks required for data communi-
cation are generated on the SCL.
Communication mode
specification bits
00 : Slave receive mode
01 : Slave transmit mode
10 : Master receive mode
11 : Master transmit mode
Note: These bits and flags can be read out, but cannot be written.
Write “0” to these bits at writing.
This bit is set to “0” in one of the following conditions.
• Immediately after completion of the byte which has lost arbitra-
tion when arbitration lost is detected
2
Fig. 60 Structure of I C status register
• When a STOP condition is detected.
• Writing “1” to this bit by software is invalid by the START condi-
tion duplication preventing function (Note).
• At reset
SCL
PIN
Note: START condition duplication preventing function
The MST, TRX, and BB bits is set to “1” at the same time after con-
firming that the BB flag is “0” in the procedure of a START condition
occurrence. However, when a START condition by another master
device occurs and the BB flag is set to “1” immediately after the con-
tents of the BB flag is confirmed, the START condition duplication
preventing function makes the writing to the MST and TRX bits in-
valid. The duplication preventing function becomes valid from the
rising of the BB flag to reception completion of slave address.
I2CIRQ
Fig. 61 Interrupt request signal generating timing
Rev.1.01 Jan 25, 2005 page 64 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
STOP Condition Generating Method
START Condition Generating Method
2
2
When the ES0 bit of the I C control register (S1D: address
When writing “1” to the MST, TRX, and BB bits of the I C status
001416) is “1,” write “1” to the MST and TRX bits, and write “0” to
register (S1: address 001316) at the same time after writing the
2
2
the BB bit of the I C status register (S1: address 001316) simulta-
slave address to the I C data shift register (S0: address 001116)
2
neously. Then a STOP condition occurs. The STOP condition
generating timing is different in the standard clock mode and the
high-speed clock mode. Refer to Figure 63, the STOP condition
generating timing diagram, and Table 10, the STOP condition gen-
erating timing table.
with the condition in which the ES0 bit of the I C control register
(S1D: address 001416) is “1” and the BB flag is “0”, a START con-
dition occurs. After that, the bit counter becomes “0002” and an
SCL for 1 byte is output. The START condition generating timing is
different in the standard clock mode and the high-speed clock
mode. Refer to Figure 62, the START condition generating timing
diagram, and Table 9, the START condition generating timing
table.
I2C status register
write signal
SCL
Setup
time
Hold time
I2C status register
write signal
SDA
SCL
Setup
Hold time
time
Fig. 63 STOP condition generating timing diagram
Table 10 STOP condition generating timing table
SDA
Standard clock mode
5.0 µs (20 cycles)
4.5 µs (18 cycles)
High-speed clock mode
3.0 µs (12 cycles)
Item
Fig. 62 START condition generating timing diagram
Table 9 START condition generating timing table
Setup time
Hold time
2.5 µs (10 cycles)
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
Item
Standard clock mode High-speed clock mode
Setup time
Hold time
5.0 µs (20 cycles)
5.0 µs (20 cycles)
2.5 µs (10 cycles)
2.5 µs (10 cycles)
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
Rev.1.01 Jan 25, 2005 page 65 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
START/STOP Condition Detecting Operation
The START/STOP condition detection operations are shown in
Figures 64, 65, and Table 11. The START/STOP condition is set
by the START/STOP condition set bit.
SCL release time
SCL
SDA
Setup
Hold time
time
BB flag
set time
The START/STOP condition can be detected only when the input
signal of the SCL and SDA pins satisfy three conditions: SCL re-
lease time, setup time, and hold time (see Table 11).
The BB flag is set to “1” by detecting the START condition and is
reset to “0” by detecting the STOP condition.
BB flag
Fig. 64 START/STOP condition detecting timing diagram
The BB flag set/reset timing is different in the standard clock mode
and the high-speed clock mode. Refer to Table 11, the BB flag set/
reset time.
SCL release time
SCL
Setup
Hold time
time
Note: When a STOP condition is detected in the slave mode (MST = 0), an
interrupt request signal “I2CIRQ” occurs to the CPU.
SDA
BB flag
reset
time
BB flag
Table 11 START condition/STOP condition detecting conditions
Fig. 65 STOP condition detecting timing diagram
Standard clock mode
High-speed clock mode
SCL release time
SSC value + 1 cycle (6.25 µs)
4 cycles (1.0 µs)
SSC value + 1
Setup time
cycle < 4.0 µs (3.125 µs)
2 cycles (0.5 µs)
2 cycles (0.5 µs)
2
SSC value + 1
Hold time
cycle < 4.0 µs (3.125 µs)
2
BB flag set/
reset time
SSC value –1
3.5 cycles (0.875 µs)
+ 2 cycles (3.375 µs)
2
Note: Unit : Cycle number of internal clock φ
SSC value is the decimal notation value of the START/STOP condi-
tion set bits SSC4 to SSC0. Do not set “0” or an odd number to SSC
value. The value in parentheses is an example when the I2C START/
STOP condition control register is set to “1816” at φ = 4 MHz.
Rev.1.01 Jan 25, 2005 page 66 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C START/STOP Condition Control Register
•Bit 6: SCL/SDA interrupt pin selection bit (SIS)
(S2D)] 001616
The I C START/STOP condition control register (S2D: address
This bit selects the pin of which interrupt becomes valid between
2
the SCL pin and the SDA pin.
Note: When changing the setting of the SCL/SDA interrupt pin polarity se-
lection bit, the SCL/SDA interrupt pin selection bit, or the I2C-BUS
interface enable bit ES0, the SCL/SDA interrupt request bit may be
set. When selecting the SCL/SDA interrupt source, disable the inter-
rupt before the SCL/SDA interrupt pin polarity selection bit, the SCL/
SDA interrupt pin selection bit, or the I2C-BUS interface enable bit
ES0 is set. Reset the request bit to “0” after setting these bits, and
enable the interrupt.
001616) controls START/STOP condition detection.
•Bits 0 to 4: START/STOP condition set bits (SSC4–SSC0)
SCL release time, setup time, and hold time change the detection
condition by value of the main clock divide ratio selection bit and
the oscillation frequency f(XIN) because these time are measured
by the internal system clock. Accordingly, set the proper value to
the START/STOP condition set bits (SSC4 to SSC0) in considered
of the system clock frequency. Refer to Table 11.
Do not set “000002” or an odd number to the START/STOP condi-
tion set bits (SSC4 to SSC0).
Refer to Table 12, the recommended set value to START/STOP
condition set bits (SSC4–SSC0) for each oscillation frequency.
•Bit 5: SCL/SDA interrupt pin polarity selection bit (SIP)
An interrupt can occur when detecting the falling or rising edge of
the SCL or SDA pin. This bit selects the polarity of the SCL or SDA
pin interrupt pin.
b7
b0
I2C START/STOP condition
control register
SSC4 SSC3 SSC2 SSC1 SSC0
SIS SIP
(S2D : address 001616)
START/STOP condition set bits
SCL/SDA interrupt pin polarity
selection bit
0 : Falling edge active
1 : Rising edge active
SCL/SDA interrupt pin selection bit
0 : SDA valid
1 : SCL valid
Not used
(Fix this bit to “0”.)
2
Fig. 66 Structure of I C START/STOP condition control register
Table 12 Recommended set value to START/STOP condition set bits (SSC4–SSC0) for each oscillation frequency
Oscillation
frequency
f(XIN) (MHz)
START/STOP
condition
control register
Internal
clock φ
(MHz)
Main clock
divide ratio
SCL release time
Setup time
Hold time
(µs)
(µs)
(µs)
3.25 µs (13 cycles)
3.0 µs (12 cycles)
2.0 µs (2 cycles)
3.0 µs (6 cycles)
2.5 µs (5 cycles)
2.0 µs (2 cycles)
XXX11010
XXX11000
XXX00100
XXX01100
XXX01010
XXX00100
6.75 µs (27 cycles)
6.25 µs (25 cycles)
5.0 µs (5 cycles)
6.5 µs (13 cycles)
5.5 µs (11 cycles)
5.0 µs (5 cycles)
3.5 µs (14 cycles)
3.25 µs (13 cycles)
3.0 µs (3 cycles)
3.5 µs (7 cycles)
3.0 µs (6 cycles)
3.0 µs (3 cycles)
8
8
4
2
2
8
2
2
4
1
2
1
Note: Do not set an odd number to the START/STOP condition set bits (SSC4 to SSC0) and “000002”.
Rev.1.01 Jan 25, 2005 page 67 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
[I C Special Mode Status Register (S3)]
•Bit 5: SCL pin low hold 2 flag (PIN2)
001216
When the ACK interrupt control bit (ACKICON) and the ACK clock
bit (ACK) are “1”, this flag is set to “0” in synchronization with the
falling of the data’s last SCL clock, just before the ACK clock. The
2
The I C special mode status register (S3: address 001216) con-
2
2
sists of the flags indicating I C operating state in the I C special
2
2
mode, which is set by the I C special mode control register (S3D:
SCL pin is simultaneously held low, and the I C interrupt request
address 001716).
occurs.
The stop condition flag is valid in all operating modes.
•Bit 0: Slave address 0 comparison flag (AAS0)
Bit 1: Slave address 1 comparison flag (AAS1)
Bit 2: Slave address 2 comparison flag (AAS2)
These flags indicate a comparison result of address data. These
flags are valid only when the slave address control bit (MSLAD) is
“1”.
This flag is initialized to “1” at reset, when the ACK interrupt con-
trol bit (ACKICON) is “0”, or when writing “1” to the SCL pin low
hold 2 flag set bit (PIN2IN).
The SCL pin is held low when either the SCL pin low hold bit (PIN)
or the SCL pin low hold 2 flag (PIN2) becomes “0”. The low hold
state of the SCL pin is released when both the SCL pin low hold
bit (PIN) and the SCL pin low hold 2 flag (PIN2) are “1”.
•Bit 7: Stop condition flag (SPCF)
In the 7-bit addressing format of the slave reception mode, the re-
spective slave address i (i = 0, 1, 2) comparison flags
This flag is set to “1” when a STOP condition occurs.
2
2
corresponding to the I C slave address registers 0 to 2 are set to
This flag is initialized to “0” at reset, when the I C-BUS interface
“1” when an address data immediately after an occurrence of a
enable bit (ES0) is “0”, or when writing “1” to the STOP condition
START condition agrees with the high-order 7-bit slave address
flag clear bit (SPFCL).
2
stored in the I C slave address registers 0 to 2 (addresses 0FF716
to 0FF916).
In the 10-bit addressing format of the slave mode, the respective
slave address i (i = 0, 1, 2) comparison flags corresponding to the
2
I C slave address registers are set to “1” when an address data is
compared with the 8 bits consisting of the slave address stored in
2
the I C slave address registers 0 to 2 and the RWB bit, and the
first byte agrees.
These flags are initialized to “0” at reset, when the slave address
2
control bit (MSLAD) is “0”, or when writing data to the I C data
shift register (S0: address 001116).
b7
b0
I2C special mode status register
(S3 : address 001216
SPCF
PIN2
AAS2 AAS1 AAS0
)
Slave address 0 comparison flag
0 : Address disagreement
1 : Address agreement
Slave address 1 comparison flag
0 : Address disagreement
1 : Address agreement
Slave address 2 comparison flag
0 : Address disagreement
1 : Address agreement
Not used
(return “0” when read)
Not used
(return “0” when read)
SCL pin low hold 2 flag
0 : SCL pin low hold
1 : SCL pin low release (Note)
Not used
(return “0” when read)
STOP condition flag
0 : No detection
1 : Detection
Note: In order that the low hold state of the SCL pin may release, it is
necessary that the SCL pin low hold 2 flag and the SCL pin low
hold bit (PIN) are “1” simultaneously.
2
Fig. 67 Structure of I C special mode status register
Rev.1.01 Jan 25, 2005 page 68 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
2
[I C Special Mode Control Register (S3D)]
•Bit 2: I C slave address control bit (MSLAD)
2
001716
This bit controls a slave address. When this bit is “0”, only the I C
slave address register 0 (address 0FF716) becomes valid as a
slave address and a read/write bit.
2
The I C special mode control register (S3D: address 001716) con-
trols special functions such as occurrence timing of reception
interrupt request and extending slave address comparison to 3
bytes.
2
When this bit is “1”, all of the I C slave address registers 0 to 2
(addresses 0FF716 to 0FF916) become valid as a slave address
and a read/write bit. In this case, when an address data agrees
•Bit 1: ACK interrupt control bit (ACKICON)
2
2
This bit controls the timing of I C interrupt request occurrence at
with any one of the I C slave address registers 0 to 2, the slave
2
completion of data receiving due to master reception or slave re-
ception.
address comparison flag (AAS) is set to “1” and the I C slave ad-
2
dress comparison flag corresponding to the agreed I C slave
When this bit is “0”, the SCL pin low hold bit (PIN) is set to “0” in
synchronization with the falling of the last SCL clock, including the
address registers 0 to 2 is also set to “1”.
•Bit 5: SCL pin low hold 2 flag set bit (PIN2IN)
Writing “1” to this bit initializes the SCL pin low hold 2 flag (PIN2)
to “1”.
2
ACK clock. The SCL pin is simultaneously held low, and the I C
interrupt request occurs.
When this bit is “1” and the ACK clock bit (ACK) is “1”, the SCL pin
low hold 2 flag (PIN2) is set to “0” in synchronization with the fall-
ing of the data’s last SCL clock, just before the ACK clock. The
When writing “0”, nothing is generated.
•Bit 6: SCL pin low hold set bit (PIN2HD)
When the SCL pin low hold bit (PIN) becomes “0”, the SCL pin is
held low. However, the SCL pin low hold bit (PIN) cannot be set to
“0” by software. The SCL pin low hold set bit (PIN2HD) is used to ,
hold the SCL pin in the low state by software. When writing “1” to
this bit, the SCL pin low hold 2 flag (PIN2) becomes “0”, and the
SCL pin is held low. When writing “0”, nothing occurs.
•Bit 7: STOP condition flag clear bit (SPFCL)
Writing “1” to this bit initializes the STOP condition flag (SPCF) to
“0”.
2
SCL pin is simultaneously held low, and the I C interrupt request
occurs again. The ACK bit can be changed after the contents of
data are confirmed by using this function.
When writing “0”, nothing is generated.
b7
b0
I2C special mode control register
ACKI
CON
PIN2-
HD
SPFCL
MSLAD
PIN2IN
(S3D : address 001716
)
Not used
(Fix this bit to “0”.)
ACK interrupt control bit
0 : At communication completion
1 : At falling of ACK clock and communication
completion
Slave address control bit
0 : One-byte slave address compare mode
1 : Three-byte slave address compare mode
Not used
(return “0” when read)
Not used
(Fix this bit to “0”.)
SCL pin low hold 2 flag set bit (Notes 1, 2)
Writing “1” to this bit initializes the SCL pin low
hold 2 flag to “1”.
SCL pin low hold set bit (Notes 1, 2)
When writing “1” to this bit, the SCL pin low
hold 2 flag becomes “0” and the SCL pin is held
low.
STOP condition flag clear bit (Note 2)
Writing “1” to this bit initializes the STOP
condition flag to “0”.
Notes 1: Do not write “1” to these bits simultaneously.
2: return “0” when read
2
Fig. 68 Structure of I C special mode control register
Rev.1.01 Jan 25, 2005 page 69 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Address Data Communication
parison, an address comparison between the RWB bit of the
2
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective
address communication formats are described below.
ꢀ 7-bit addressing format
I C slave address register and the R/W bit which is the last bit
of the address data transmitted from the master is made. In the
10-bit addressing mode, the RWB bit which is the last bit of the
address data not only specifies the direction of communication
for control data, but also is processed as an address data bit.
When the first-byte address data agree with the slave address,
To adapt the 7-bit addressing format, set the 10BIT SAD bit of
2
the I C control register (S1D: address 001416) to “0”. The first 7-
2
bit address data transmitted from the master is compared with
the AAS bit of the I C status register (S1: address 001316) is
2
the high-order 7-bit slave address stored in the I C slave ad-
set to “1.” After the second-byte address data is stored into the
2
dress register. At the time of this comparison, address
I C data shift register (S0: address 001116), perform an ad-
2
comparison of the RWB bit of the I C slave address register is
dress comparison between the second-byte data and the slave
address by software. When the address data of the 2 bytes
not performed. For the data transmission format when the 7-bit
addressing format is selected, refer to Figure 69, (1) and (2).
ꢀ 10-bit addressing format
2
agree with the slave address, set the RWB bit of the I C slave
address register to “1” by software. This processing can make
the 7-bit slave address and R/W data agree, which are re-
ceived after a RESTART condition is detected, with the value of
To adapt the 10-bit addressing format, set the 10BIT SAD bit of
2
the I C control register (S1D: address 001416) to “1.” An ad-
2
dress comparison is performed between the first-byte address
data transmitted from the master and the 8-bit slave address
the I C slave address register. For the data transmission for-
mat when the 10-bit addressing format is selected, refer to
Figure 69, (3) and (4).
2
stored in the I C slave address register. At the time of this com-
(1) A master-transmitter transmits data to a slave-receiver
A
Data
A
Data
S
Slave address R/W
7 bits “0”
A/A
A
P
1 to 8 bits
1 to 8 bits
(2) A master-receiver receives data from a slave-transmitter
A
Data
A
Data
S
Slave address R/W
7 bits “1”
P
1 to 8 bits
1 to 8 bits
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address
Slave address
2nd bytes
Slave address
1st 7 bits
A/A
A
A
Data
Data
S
R/W
A
P
1 to 8 bits
1 to 8 bits
7 bits
“0”
8 bits
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address
Slave address
2nd bytes
Slave address
1st 7 bits
Slave address
1st 7 bits
Sr
A
A
A
Data
1 to 8 bits
Data
P
S
R/W
R/W
A
A
“1”
1 to 8 bits
7 bits
“0”
8 bits
7 bits
S : START condition
A : ACK bit
Sr : Restart condition
P : STOP condition
R/W : Read/Write bit
: Master to slave
: Slave to master
Fig. 69 Address data communication format
Rev.1.01 Jan 25, 2005 page 70 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Example of Master Transmission
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz and in the ACK return mode is
shown below.
Example of Slave Reception
An example of slave reception in the high-speed clock mode, at
the SCL frequency of 400 kHz, in the ACK non-return mode and
using the addressing format is shown below.
2
2
ꢀ Set a slave address in the high-order 7 bits of the I C slave ad-
ꢀ Set a slave address in the high-order 7 bits of the I C slave ad-
dress register and “0” into the RWB bit.
dress register and “0” in the RWB bit.
ꢀ Set the ACK return mode and SCL = 100 kHz by setting “8516”
ꢀ Set the no ACK clock mode and SCL = 400 kHz by setting
2
2
in the I C clock control register (S2: address 001516).
“2516” in the I C clock control register (S2: address 001516).
2
2
ꢀ Set “0016” in the I C status register (S1: address 001316) so
ꢀ Set “0016” in the I C status register (S1: address 001316) so
that transmission/reception mode can become initializing condi-
that transmission/reception mode can become initializing condi-
tion.
tion.
2
2
ꢀ Set a communication enable status by setting “0816” in the I C
ꢀ Set a communication enable status by setting “0816” in the I C
control register (S1D: address 001416).
control register (S1D: address 001416).
ꢀ When a START condition is received, an address comparison is
performed.
2
ꢀ Confirm the bus free condition by the BB flag of the I C status
register (S1: address 001316).
ꢀ Set the address data of the destination of transmission in the
ꢀꢀ•When all transmitted addresses are “0” (general call):
2
2
high-order 7 bits of the I C data shift register (S0: address
AD0 of the I C status register (S1: address 001316) is set to “1”
001116) and set “0” in the least significant bit.
and an interrupt request signal occurs.
2
ꢀ Set “F016” in the I C status register (S1: address 001316) to
• When the transmitted addresses agree with the address set in
ꢀ:
generate a START condition. At this time, an SCL for 1 byte and
2
an ACK clock automatically occur.
AAS of the I C status register (S1: address 001316) is set to
2
ꢀ Set transmit data in the I C data shift register (S0: address
“1” and an interrupt request signal occurs.
2
001116). At this time, an SCL and an ACK clock automatically
• In the cases other than the above AD0 and AAS of the I C sta-
occur.
tus register (S1: address 001316) are set to “0” and no interrupt
ꢀ When transmitting control data of more than 1 byte, repeat step
ꢀ.
request signal occurs.
2
ꢀ Set dummy data in the I C data shift register (S0: address
2
ꢀ Set “D016” in the I C status register (S1: address 001316) to
001116).
generate a STOP condition if ACK is not returned from slave re-
ception side or transmission ends.
ꢀ When receiving control data of more than 1 byte, repeat step ꢀ.
ꢀ When a STOP condition is detected, the communication ends.
Rev.1.01 Jan 25, 2005 page 71 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
2
ꢀPrecautions when using multi-master I C-
BUS interface
5. Disable interrupts during the following three process steps:
• BB flag confirming
• Writing of slave address value
(1) Read-modify-write instruction
The precautions when the read-modify-write instruction such as
SEB, CLB etc. is executed for each register of the multi-master
• Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
2
I C-BUS interface are described below.
2
• I C data shift register (S0: address 001116)
When executing the read-modify-write instruction for this regis-
ter during transfer, data may become a value not intended.
(3) RESTART condition generating procedure
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 4.)
Execute the following procedure when the PIN bit is “0.”
2
• I C slave address registers 0 to 2 (S0D0 to S0D2: addresses
0FF716 to0FF916)
:
When the read-modify-write instruction is executed for this regis-
ter at detecting the STOP condition, data may become a value
not intended. It is because H/W changes the read/write bit
(RWB) at the above timing.
:
LDM #$00, S1
LDA —
(Select slave receive mode)
(Taking out of slave address value)
(Interrupt disabled)
SEI
2
• I C status register (S1: address 001316)
STAS0
(Writing of slave address value)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by H/W.
LDM #$F0, S1
CLI
(
Trigger of RESTART condition generating
)
(Interrupt enabled)
2
:
:
• I C control register (S1D: address 001416)
When the read-modify-write instruction is executed for this regis-
ter at detecting the START condition or at completing the byte
transfer, data may become a value not intended. Because H/W
changes the bit counter (BC0-BC2) at the above timing.
2. Select the slave receive mode when the PIN bit is “0.” Do not
write “1” to the PIN bit. Neither “0” nor “1” is specified for the
writing to the BB bit.
The TRX bit becomes “0” and the SDA pin is released.
3. The SCL pin is released by writing the slave address value to
2
• I C clock control register (S2: address 001516)
2
The read-modify-write instruction can be executed for this regis-
ter.
the I C data shift register.
4. Disable interrupts during the following two process steps:
• Writing of slave address value
2
• I C START/STOP condition control register (S2D: address
001616)
• Trigger of RESTART condition generating
The read-modify-write instruction can be executed for this regis-
ter.
2
(4) Writing to I C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and
an instruction to set the MST and TRX bits to “0” from “1” simulta-
neously. It is because it may enter the state that the SCL pin is
released and the SDA pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to “0” from “1” simultaneously when the PIN bit is “1.” It is because
it may become the same as above.
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 5.
:
:
LDA —
(Taking out of slave address value)
(Interrupt disabled)
SEI
BBS 5, S1, BUSBUSY (BB flag confirming and branch process)
BUSFREE:
(5) Process of after STOP condition generating
2
2
STA S0
(Writing of slave address value)
(Trigger of START condition generating)
(Interrupt enabled)
Do not write data in the I C data shift register S0 and the I C sta-
tus register S1 until the bus busy flag BB becomes “0” after
generating the STOP condition in the master mode. It is because
the STOP condition waveform might not be normally generated.
Reading to the above registers does not have the problem.
LDM #$F0, S1
CLI
:
:
BUSBUSY:
CLI
(Interrupt enabled)
:
:
2. Use “Branch on Bit Set” of “BBS 5, S1, –” for the BB flag con-
firming and branch process.
3. Use “STA $12, STX $12” or “STY $12” of the zero page ad-
dressing instruction for writing the slave address value to the
2
I C data shift register.
4. Execute the branch instruction of above 2 and the store instruc-
tion of above 3 continuously shown the above procedure
example.
Rev.1.01 Jan 25, 2005 page 72 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
RESET CIRCUIT
To reset the microcomputer, RESET pin should be held at an “L”
level for 16 cycles or more of XIN. Then the RESET pin is returned
to an “H” level (the power source voltage should be between 2.7 V
to 5.5 V, and the oscillation should be stable), reset is released.
After the reset is completed, the program starts from the address
contained in address FFFD16 (high-order byte) and address
FFFC16 (low-order byte).
2.7 V
VCC
0V
RESET
VCC
RESET
0V
0.2VCC or less
td(P-R)+XIN 16 cycles or more
Input to the RESET pin in the following procedure.
ꢀWhen power source is stabilized
5V
2.7 V
(1) Input “L” level to RESET pin.
VCC
Power source
voltage detection
circuit
RESET
VCC
0V
5V
(2) Input “L” level for 16 cycles or more to XIN pin.
(3) Input “H” level to RESET pin.
RESET
0V
ꢀAt power-on
td(P-R)+XIN 16 cycles or more
(1) Input “L” level to RESET pin.
(2) Increase the power source voltage to 2.7 V.
(3) Wait for td(P-R) until internal power source has stabilized.
(4) Input “L” level for 16 cycles or more to XIN pin.
(5) Input “H” level to RESET pin.
Example at VCC = 5V
Fig. 70 Reset circuit example
X
IN
φ
RESET
Internal
reset
Address
AD
H,L
?
?
?
?
FFFC
FFFD
Reset address from the vector table.
Data
ADH
?
?
?
ADL
?
SYNC
XIN: 10.5 to 18.5 clock cycles
Notes
1: The frequency relation of f(XIN) and f(φ) is f(XIN)=8
• f(φ).
2: The question marks (?) indicate an undefined state that depends on the previous state.
Fig. 71 Reset sequence
Rev.1.01 Jan 25, 2005 page 73 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Address
Register contents
Register contents
Address
(1)
0016
Port P0 (P0)
FF16
FF16
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
001116
001216
001316
001416
001516
Timer Z (low-order) (TZL)
(41)
(42)
(43)
(44)
(45)
(46)
(47)
(48)
(49)
(50)
(51)
(52)
(53)
(54)
(55)
(56)
(57)
(58)
(59)
(60)
(61)
(62)
(63)
(64)
(65)
(66)
(67)
(68)
(69)
(70)
(71)
(72)
(73)
(74)
(75)
(76)
(77)
002816
002916
002A16
002B16
002C16
002D16
002F16
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
0FE016
0FE116
0FE216
0FF016
0FF116
0FF216
0FF316
0FF416
0FF516
0FF616
0FF716
0FF816
0FF916
(PS)
(2)
0016
Port P0 direction register (P0D)
Port P1 (P1)
Timer Z (high-order) (TZH)
(3)
0016
0016
Timer Z mode register (TZM)
PWM control register (PWMCON)
PWM prescaler (PREPWM)
(4)
0016
Port P1 direction register (P1D)
Port P2 (P2)
0016
(5)
0016
X X X X X X X X
X X X X X X X X
X X X X X X X X
(6)
0016
Port P2 direction register (P2D)
Port P3 (P3)
PWM register (PWM)
(7)
0016
Baud rate generator 3 (BRG3)
Transmit/Receive buffer register 3 (TB3/RB3)
Serial I/O3 status register (SIO3STS)
Serial I/O3 control register (SIO3CON)
UART3 control register (UART3CON)
AD/DA control register (ADCON)
AD conversion register 1 (AD1)
DA1 conversion register (DA1)
DA2 conversion register (DA2)
AD conversion register 2 (AD2)
Interrupt source selection register (INTSEL)
Interrupt edge selection register (INTEDGE)
CPU mode register (CPUM)
(8)
0016
Port P3 direction register (P3D)
Port P4 (P4)
X X X X X X X X
1 0 0 0 0 0 0 0
0016
(9)
0016
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
(30)
(31)
(32)
(33)
(34)
(35)
(36)
(37)
(38)
(39)
(40)
0016
0016
Port P4 direction register (P4D)
Port P5 (P5)
1 1 1 0 0 0 0 0
0016
Port P5 direction register (P5D)
Port P6 (P6)
0 0 0 0 1 0 0 0
X X X X X X X X
0016
0016
Port P6 direction register (P6D)
Timer 12, X count source selection register (T12XCSS)
Timer Y, Z count source selection register (TYZCSS)
MISRG
0016
0 0 1 1 0 0 1 1
0 0 1 1 0 0 1 1
0016
0016
0 0 0 0 0 0 X X
0016
I2C data shift register (S0)
I2C special mode status register (S3)
I2C status register (S1)
I2C control register (S1D)
X X X X X X X X
0 0 1 0 0 0 0 0
0016
0 1 0 0 1 0 0 0
0016
Interrupt request register 1 (IREQ1)
Interrupt request register 2 (IREQ2)
Interrupt control register 1 (ICON1)
Interrupt control register 2 (ICON2)
Flash memory control register 0 (FMCR0)
Flash memory control register 1 (FMCR1)
Flash memory control register 2 (FMCR2)
Port P0 pull-up control register (PULL0)
Port P1 pull-up control register (PULL1)
Port P2 pull-up control register (PULL2)
Port P3 pull-up control register (PULL3)
Port P4 pull-up control register (PULL4)
Port P5 pull-up control register (PULL5)
Port P6 pull-up control register (PULL6)
I2C slave address register 0 (S0D0)
I2C slave address register 1 (S0D1)
I2C slave address register 2 (S0D3)
Processor status register
0 0 0 1 0 0 0 X
0016
0016
I2C clock control register (S2)
2
0016
0016
0 0 0 1 1 0 1 0
I C START/STOP condition control register (S2D)
I2C special mode control register (S3D)
Transmit/Receive buffer register 1 (TB1/RB1)
Serial I/O1 status register (SIO1STS)
0016
001616
001716
001816
001916
001A16
001B16
001C16
001D16
001E16
001F16
002016
002116
002216
002316
002416
002516
002616
002716
0016
0116
X X X X X X X X
1 0 0 0 0 0 0 0
4016
4516
0016
Serial I/O1 control register (SIO1CON)
UART1 control register (UART1CON)
Baud rate generator 1 (BRG1)
Serial I/O2 control register (SIO2CON)
Watchdog timer control register (WDTCON)
Serial I/O2 register (SIO2)
Prescaler 12 (PRE12)
0016
1 1 1 0 0 0 0 0
0016
X X X X X X X X
0016
0016
0016
0 0 1 1 1 1 1 1
0016
X X X X X X X X
0016
FF16
0116
FF16
0016
FF16
FF16
FF16
FF16
0016
Timer 1 (T1)
0016
Timer 2 (T2)
0016
Timer XY mode register (TM)
Prescaler X (PREX)
0016
X X X X X
1 X X
Timer X (TX)
Program counter
(PCH)
FFFD16 contents
FFFC16 contents
Prescaler Y (PREY)
(PCL)
Timer Y (TY)
Note : X : Not fixed
Since the initial values for other than above mentioned registers and
RAM contents are indefinite at reset, they must be set.
Fig. 72 Internal status at reset
Rev.1.01 Jan 25, 2005 page 74 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
CLOCK GENERATING CIRCUIT
Oscillation Control
The 3804 group (Spec. H) has two built-in oscillation circuits: main
clock XIN-XOUT oscillation circuit and sub clock XCIN-XCOUT oscil-
lation circuit. An oscillation circuit can be formed by connecting a
resonator between XIN and XOUT (XCIN and XCOUT). Use the cir-
cuit constants in accordance with the resonator manufacturer’s
recommended values. No external resistor is needed between XIN
and XOUT since a feed-back resistor exists on-chip.(An external
feed-back resistor may be needed depending on conditions.)
However, an external feed-back resistor is needed between XCIN
and XCOUT.
(1) Stop mode
If the STP instruction is executed, the internal clock φ stops at an
“H” level, and XIN and XCIN oscillators stop. When the oscillation
stabilizing time set after STP instruction released bit is “0,” the
prescaler 12 is set to “FF16” and timer 1 is set to “0116.” When the
oscillation stabilizing time set after STP instruction released bit is
“1,” set the sufficient time for oscillation of used oscillator to stabi-
lize since nothing is set to the prescaler 12 and timer 1.
After STP instruction is released, the input of the prescaler 12 is
connected to count source which had set at executing the STP in-
struction, and the output of the prescaler 12 is connected to timer
1. Set the timer 1 interrupt enable bit to disabled (“0”) before ex-
ecuting the STP instruction. Oscillator restarts when an external
interrupt is received, but the internal clock φ is not supplied to the
CPU (remains at “H”) until timer 1 underflows. The internal clock φ
is supplied for the first time, when timer 1 underflows. Therefore
make sure not to set the timer 1 interrupt request bit to “1” before
the STP instruction stops the oscillator. When the oscillator is re-
started by reset, apply “L” level to the RESET pin until the
oscillation is stable since a wait time will not be generated.
The internal power supply circuit is changed to low power con-
sumption mode for consumption current reduction at the time of
STP instruction execution.
Immediately after power on, only the XIN oscillation circuit starts
oscillating, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
(1) Middle-speed mode
The internal clock φ is the frequency of XIN divided by 8. After re-
set is released, this mode is selected.
(2) High-speed mode
The internal clock φ is half the frequency of XIN.
(3) Low-speed mode
The internal clock φ is half the frequency of XCIN.
Although an internal power supply circuit is usually changed to the
normal operation mode at the time of the return from an STP in-
struction, since a certain time is required to start the power supply
to the flash memory and operation of flash memory to be enabled,
set wait time 100 µs or more by the oscillation stabilization time
set function after release of the STP instruction which used the
timer 1.
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping
the main clock XIN in low-speed mode. To stop the main clock, set
bit 5 of the CPU mode register to “1.” When the main clock XIN is
restarted (by setting the main clock stop bit to “0”), set sufficient
time for oscillation to stabilize.
(2) Wait mode
If the WIT instruction is executed, the internal clock φ stops at an
“H” level, but the oscillator does not stop. The internal clock φ re-
starts when an interrupt is received. Since the oscillator does not
stop, normal operation can be started immediately after the clock
is restarted.
ꢀNote
•If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The sufficient time
is required for the sub clock to stabilize, especially immediately
after power on and at returning from stop mode. When switching
the mode between middle/high-speed and low-speed, set the fre-
quency on condition that f(XIN) > 3f(XCIN).
•When using the quartz-crystal oscillator of high frequency, such
as 16 MHz etc., it may be necessary to select a specific oscillator
with the specification demanded.
Rev.1.01 Jan 25, 2005 page 75 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
X
CIN
X
COUT
XIN
XOUT
Rd (Note)
Rf
Rd
C
COUT
C
IN
COUT
C
CIN
Notes : Insert a damping resistor if required.
The resistance will vary depending on the oscillator and
the oscillation drive capacity setting.
Use the value recommended by the maker of the
oscillator.
Also, if the oscillator manufacturer's data sheet
specifies that a feedback resistor be added external to
the chip though a feedback resistor exists on-chip,
insert a feedback resistor between XIN and XOUT
following the instruction.
Fig. 73 Ceramic resonator circuit
X
CIN
X
COUT
XIN
XOUT
Open
Open
External oscillation
circuit
External oscillation
circuit
V
CC
SS
V
CC
SS
V
V
Fig. 74 External clock input circuit
Rev.1.01 Jan 25, 2005 page 76 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
X
COUT
XCIN
“0”
“1”
Port X
C
switch bit
X
OUT
X
IN
Main clock division ratio
selection bits (Note 1)
Low-speed
(Note 4)
Divider
mode
Prescaler 12
(Note 3)
Timer 1
1/2
1/4
High-speed or
middle-speed
mode
Reset or
STP instruction
(Note 2)
Main clock division ratio
selection bits (Note 1)
Middle-speed mode
Timing φ (internal clock)
High-speed or
low-speed mode
Main clock stop bit
Reset
Q
S
R
S
R
Q
Q
S
R
STP instruction
STP instruction
WIT instruction
Reset
Interrupt disable flag l
Interrupt request
Notes 1: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register.
When low-speed mode is selected, set port Xc switch bit (b4) to “1”.
2: f(XIN)/16 is supplied as the count source to the prescaler 12 at reset. The count source before executing the STP
instruction is supplied as the count source at executing STP instruction.
3: When bit 0 of MISRG is “0”, timer 1 is set “0116” and prescaler 12 is set “FF16” automatically. When bit 0 of MISRG is
“1”, set the appropriate value to them in accordance with oscillation stablizing time required by the using oscillator
because nothing is automatically set into timer 1 and prescaler 12.
4: Although a feed-back resistor exists on-chip, an external feed-back resistor may be needed depending on conditions.
Fig. 75 System clock generating circuit block diagram
Rev.1.01 Jan 25, 2005 page 77 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Reset
High-speed mode
Middle-speed mode
(f(φ)=4 MHz)
(f(φ)=1 MHz)
CM
6
“1”←→“0”
CM
CM
CM
CM
7
6
5
4
=0
=1
CM
CM
CM
CM
7
=0
6
5
4
=0
=0(8 MHz oscillating)
=0(32 kHz stopped)
=0(8 MHz oscillating)
=0(32 kHz stopped)
C
M
“
”
4
0
0
”
“
←
C
4
→
M
→
M
“
”
6
C
1
←
“
”
0
”
1
”
“
←
1
6
M
“
→
→
“
C
←
”
0
1
”
“
Middle-speed mode
(f(φ)=1 MHz)
High-speed mode
(f(φ)=4 MHz)
CM
6
“1”←→“0”
CM
CM
CM
CM
7
=0
CM
CM
CM
CM
7
=0
6=1
6
5
4
=0
5
=0(8 MHz oscillating)
=1(32 kHz oscillating)
=0(8 MHz oscillating)
=1(32 kHz oscillating)
4
C
M
“
7
0
”
←
C
M
→
“
6
1
“
1
”
←
”
→
“
0
”
Low-speed mode
(f(φ)=16 kHz)
CM
CM
CM
CM
7
=1
6
5
4
=0
b7
b4
=0(8 MHz oscillating)
=1(32 kHz oscillating)
CPU mode register
(CPUM : address 003B16
)
CM
CM
CM
4
5
7
: Port Xc switch bit
0 : I/O port function (stop oscillating)
1 : XCIN-XCOUT oscillating function
: Main clock (XIN- XOUT) stop bit
0 : Operating
1 : Stopped
, CM
6: Main clock division ratio selection bit
Low-speed mode
(f(φ)=16 kHz)
b7 b6
0
0
1
1
0 : φ = f(XIN)/2 ( High-speed mode)
1 : φ = f(XIN)/8 (Middle-speed mode)
0 : φ = f(XCIN)/2 (Low-speed mode)
1 : Not available
CM
CM
CM
CM
7
=1
=0
6
5
4
=1(8 MHz stopped)
=1(32 kHz oscillating)
Notes
1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.)
2 : The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is
ended.
3 : Timer operates in the wait mode.
4 : When the stop mode is ended, a delay of approximately 1 ms occurs by connecting prescaler 12 and Timer 1 in middle/high-speed mode.
5 : When the stop mode is ended, a delay of approximately 0.25 s occurs by Timer 1 and Timer 2 in low-speed mode.
6 : Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle/high-speed
mode.
7 : The example assumes that 8 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. φ indicates the internal clock.
Fig. 76 State transitions of system clock
Rev.1.01 Jan 25, 2005 page 78 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
FLASH MEMORY MODE
The 3804 group (spec. H) has the flash memory that can be re-
written with a single power source.
For this flash memory, three flash memory modes are available in
which to read, program, and erase: the parallel I/O and standard
serial I/O modes in which the flash memory can be manipulated
using a programmer and the CPU rewrite mode in which the flash
memory can be manipulated by the Central Processing Unit
(CPU).
This flash memory has some blocks on it as shown in Figure 77
and each block can be erased.
In addition to the ordinary User ROM area to store the MCU op-
eration control program, the flash memory has a Boot ROM area
that is used to store a program to control rewriting in CPU rewrite
and standard serial I/O modes. This Boot ROM area has had a
standard serial I/O mode control program stored in it when
shipped from the factory. However, the user can write a rewrite
control program in this area that suits the user’s application sys-
tem. This Boot ROM area can be rewritten in only parallel I/O
mode.
ꢀ Summary
Table 13 lists the summary of the 3804 Group (spec. H).
Table 13 Summary of 3804 group (spec. H)
Item
Specifications
Power source voltage (Vcc)
Program/Erase VPP voltage (VPP)
Flash memory mode
VCC = 2.7 to 5.5 V
VCC = 2.7 to 5.5 V
3 modes; Parallel I/O mode, Standard serial I/O mode, CPU rewrite mode
Erase block division
User ROM area/Data ROM area Refer to Fig. 77.
Boot ROM area (Note)
Not divided (4K bytes)
Program method
Erase method
In units of bytes
Block erase
Program/Erase control method
Number of commands
Program/Erase control by software command
5 commands
Number of program/Erase times
ROM code protection
100
Available in parallel I/O mode and standard serial I/O mode
Note: The Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory.
This Boot ROM area can be erased and written in only parallel I/O mode.
Rev.1.01 Jan 25, 2005 page 79 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀ Boot Mode
ꢀ CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated
on (read, program, or erase) under control of the Central Process-
ing Unit (CPU).
The control program for CPU rewrite mode must be written into
the User ROM or Boot ROM area in parallel I/O mode beforehand.
(If the control program is written into the Boot ROM area, the stan-
dard serial I/O mode becomes unusable.)
In CPU rewrite mode, only the User ROM area shown in Figure 77
can be rewritten; the Boot ROM area cannot be rewritten. Make
sure the program and block erase commands are issued for only
the User ROM area and each block area.
See Figure 77 for details about the Boot ROM area.
Normal microcomputer mode is entered when the microcomputer
is reset with pulling CNVSS pin low. In this case, the CPU starts
operating using the control program in the User ROM area.
When the microcomputer is reset and the CNVSS pin high after
pulling the P45/TxD1 pin and CNVss pin high, the CPU starts op-
erating (start address of program is stored into addresses FFFC16
and FFFD16) using the control program in the Boot ROM area.
This mode is called the “Boot mode”. Also, User ROM area can be
rewritten using the control program in the Boot ROM area.
The control program for CPU rewrite mode can be stored in either
User ROM or Boot ROM area. In the CPU rewrite mode, because
the flash memory cannot be read from the CPU, the rewrite con-
trol program must be transferred to internal RAM area before it
can be executed.
ꢀ Block Address
Block addresses refer to the maximum address of each block.
These addresses are used in the block erase command.
000016
User ROM area
Data block B:
2K bytes
Data block A:
2K bytes
SFR area
100016
180016
200016
004016
083F16
Internal RAM area
(2K bytes)
RAM
Block 3: 24K bytes
Notes 1: The boot ROM area can be rewritten in a paral-
lel I/O mode. (Access to except boot ROM
area is disablrd.)
0FE016
Block 2: 16K bytes
Block 1: 8 K bytes
SFR area
0FFF16
100016
2: To specify a block, use the maximum address
in the block.
C00016
E00016
FFFF16
Internal flash memory area
(60K bytes)
F00016
Boot ROM area
4K bytes
Block 0: 8 K bytes
FFFF16
FFFF16
Fig. 77 Block diagram of built-in flash memory
Rev.1.01 Jan 25, 2005 page 80 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
ꢀOutline Performance
CPU rewrite mode is usable in the single-chip or Boot mode. The
Flash memory control register 0
(FMCR0: address : 0FE016: initial value: 0116
)
RY/BY status flag
0 : Busy (being written or erased)
1 : Ready
only User ROM area can be rewritten.
In CPU rewrite mode, the CPU erases, programs and reads the in-
ternal flash memory as instructed by software commands. This
rewrite control program must be transferred to internal RAM area
before it can be executed.
CPU rewrite mode select bit (Note 1)
0 : CPU rewrite mode invalid
1 : CPU rewrite mode valid
8KB user block E/W enable bit (Notes 1, 2)
0 : E/W disabled
The MCU enters CPU rewrite mode by setting “1” to the CPU re-
write mode select bit (bit 1 of address 0FE016). Then, software
commands can be accepted.
1 : E/W enabled
Flash memory reset bit (Notes 3, 4)
0 : Normal operation
1 : reset
Not used (do not write “1” to this bit.)
Use software commands to control program and erase operations.
Whether a program or erase operation has terminated normally or
in error can be verified by reading the status register.
Figure 78 shows the flash memory control register 0.
Bit 0 of the flash memory control register 0 is the RY/BY status
flag used exclusively to read the operating status of the flash
memory. During programming and erase operations, it is “0”
(busy). Otherwise, it is “1” (ready).
User ROM area select bit (Note 5)
0 : Boot ROM area is accessed
1 : User ROM area is accessed
Program status flag
0: Pass
1: Error
Erase status flag
0: Pass
1: Error
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to
this bit.
Bit 1 of the flash memory control register 0 is the CPU rewrite
mode select bit. When this bit is set to “1”, the MCU enters CPU
rewrite mode. And then, software commands can be accepted. In
CPU rewrite mode, the CPU becomes unable to access the inter-
nal flash memory directly. Therefore, use the control program in
the internal RAM for write to bit 1. To set this bit 1 to “1”, it is nec-
essary to write “0” and then write “1” in succession to bit 1. The bit
can be set to “0” by only writing “0”.
2: This bit can be written only when CPU rewrite mode select bit is “1”.
3: Effective only when the CPU rewrite mode select bit = “1”. Fix this
bit to “0” when the CPU rewrite mode select bit is “0”.
4: When setting this bit to “1” (when the control circuit of flash memory
is reset), the flash memory cannot be accessed for 10 µs.
5: Write to this bit in program on RAM
Fig. 78 Structure of flash memory control register 0
b7
b0
Bit 2 of the flash memory control register 0 is the 8 KB user block
E/W enable bit. By setting combination of bit 4 of the flash memory
control register 2 and this bit as shown in Table 14, E/W is dis-
abled to user block in the CPU rewriting mode.
Flash memory control register 1
(FMCR1: address : 0FE116: initial value: 4016
)
Erase Suspend enble bit (Notes 1)
0 : Suspend invalid
1 : Suspend valid
Bit 3 of the flash memory control register 0 is the flash memory re-
set bit used to reset the control circuit of internal flash memory.
This bit is used when flash memory access has failed. When the
CPU rewrite mode select bit is “1”, setting “1” for this bit resets the
control circuit. To release the reset, it is necessary to set this bit to
“0”.
Erase Suspend request bit (Notes 2)
0 : Erase restart
1 : Suspend request
Not used (do not write “1” to this bit.)
Erase Suspend flag
0 : Erase active
1 : Erase inactive (Erase Suspend mode)
Bit 5 of the flash memory control register 0 is the User ROM area
select bit and is valid only in the boot mode. Setting this bit to “1”
in the boot mode switches an accessible area from the boot ROM
area to the user ROM area. To use the CPU rewrite mode in the
boot mode, set this bit to “1”. To rewrite bit 5, execute the user-
original reprogramming control software transferred to the internal
RAM in advance.
Not used (do not write “1” to this bit.)
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to
this bit.
2: Effective only when the suspend enable bit = “1”.
Fig. 79 Structure of flash memory control register 1
Bit 6 of the flash memory control register 0 is the program status
flag. This bit is set to “1” when writing to flash memory is failed.
When program error occurs, the block cannot be used.
Bit 7 of the flash memory control register 0 is the erase status flag.
This bit is set to “1” when erasing flash memory is failed. When
erase error occurs, the block cannot be used.
Figure 79 shows the flash memory control register 1.
Bit 0 of the flash memory control register 1 is the Erase suspend
enable bit. By setting this bit to “1”, the erase suspend mode to
suspend erase processing temporaly when block erase command
is executed can be used. In order to set this bit to “1”, writing “0”
and “1” in succession to bit 0. In order to set this bit to “0”, write “0”
only to bit 0.
Bit 1 of the flash memory control register 1 is the erase suspend
request bit. By setting this bit to “1” when erase suspend enable
bit is “1”, the erase processing is suspended.
Bit 6 of the flash memory control register 1 is the erase suspend
flag. This bit is cleared to “0” at the flash erasing.
Rev.1.01 Jan 25, 2005 page 81 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
b7
b0
Flash memory control register 2
(FMCR2: address : 0FE216: initial value: 4516)
Not used
Not used (do not write “1” to this bit.)
Not used
All user block E/W enable bit (Notes 1, 2)
0 : E/W disabled
1 : E/W enabled
Not used
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to
this bit.
2: Effective only when the CPU rewrite mode select bit = “1”.
Fig. 80 Structure of flash memory control register 2
Table 14 State of E/W inhibition function
All user block E/W
8 KB user block E/W
8 KB ꢀꢀ2 block
Addresses C00016 to FFFF16
E/W disabled
16 KB + 24 KB block
Data block
enable bit
enable bit
Addresses 200016 to BFFF16 Addresses 100016 to 1FFF16
0
0
1
1
0
1
0
1
E/W disabled
E/W disabled
E/W enabled
E/W enabled
E/W enabled
E/W enabled
E/W enabled
E/W enabled
E/W disabled
E/W disabled
E/W enabled
Figure 81 shows a flowchart for setting/releasing CPU rewrite
mode.
Start
Single-chip mode or Boot mode
Set CPU mode register (Note 1)
Transfer CPU rewrite mode control program to
internal RAM
Jump to control program transferred to internal
RAM
(Subsequent operations are executed by control
program in this RAM)
Set CPU rewrite mode select bit to “1” (by
writing “0” and then “1” in succession)
Set all user block E/W enable bit to “1”
(by writing “0” and then “1” in succession)
Set 8 KB user block E/W enable bit
(At E/W disabled; writing “0”, at E/W enabled;
writing “0” and then “1” in succession)
Using software command executes erase,
program, or other operation
Execute read array command (Note 2)
Set all user block E/W enable bit to “0”
Set 8 KB user block E/W enable bit to “0”
Write “0” to CPU rewrite mode select bit
End
Notes 1: Set the main clock as follows depending on the clock division ratio selection bits of CPU
mode register (bits 6, 7 of address 003B16).
2: Before exiting the CPU rewrite mode after completing erase or program operation, always
be sure to execute the read array command.
Fig. 81 CPU rewrite mode set/release flowchart
Rev.1.01 Jan 25, 2005 page 82 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀ Notes on CPU Rewrite Mode
Take the notes described below when rewriting the flash memory
in CPU rewrite mode.
ꢀOperation speed
During CPU rewrite mode, set the system clock φ to 4.0 MHz or
less using the clock division ratio selection bits (bits 6 and 7 of ad-
dress 003B16).
ꢀInstructions inhibited against use
The instructions which refer to the internal data of the flash
memory cannot be used during CPU rewrite mode.
ꢀInterrupts
The interrupts cannot be used during CPU rewrite mode because
they refer to the internal data of the flash memory.
ꢀWatchdog timer
If the watchdog timer has been already activated, internal reset
due to an underflow will not occur because the watchdog timer is
surely cleared during program or erase.
ꢀReset
Reset is always valid. The MCU is activated using the boot mode
at release of reset in the condition of CNVss = “H”, so that the pro-
gram will begin at the address which is stored in addresses
FFFC16 and FFFD16 of the boot ROM area.
Rev.1.01 Jan 25, 2005 page 83 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀSoftware Commands
The RY/BY status flag of the flash memory control register is “0”
during write operation and “1” when the write operation is com-
pleted as is the status register bit 7.
Table 15 lists the software commands.
After setting the CPU rewrite mode select bit to “1”, execute a soft-
ware command to specify an erase or program operation.
Each software command is explained below.
At program end, program results can be checked by reading the
status register.
• Read Array Command (FF16)
The read array mode is entered by writing the command code
“FF16” in the first bus cycle. When an address to be read is input
in one of the bus cycles that follow, the contents of the specified
address are read out at the data bus (D0 to D7).
Start
Write “4016
”
The read array mode is retained until another command is written.
• Read Status Register Command (7016)
Write address
Write data
Write
When the command code “7016” is written in the first bus cycle,
the contents of the status register are read out at the data bus (D0
to D7) by a read in the second bus cycle.
The status register is explained in the next section.
Read status register
• Clear Status Register Command (5016)
This command is used to clear the bits SR4 and SR5 of the status
register after they have been set. These bits indicate that opera-
tion has ended in an error. To use this command, write the
command code “5016” in the first bus cycle.
SR7 = “1”?
or
RY/BY = “1” ?
NO
NO
YES
SR4 = “0”?
YES
• Program Command (4016)
Program
error
Program operation starts when the command code “4016” is writ-
ten in the first bus cycle. Then, if the address and data to program
are written in the 2nd bus cycle, program operation (data program-
ming and verification) will start.
Whether the write operation is completed can be confirmed by
Program
_____
read status register or the RY/BY status flag. When the program
starts, the read status register mode is entered automatically and
the contents of the status register is read at the data bus (D0 to
D7). The status register bit 7 (SR7) is set to “0” at the same time
the write operation starts and is returned to “1” upon completion of
the write operation. In this case, the read status register mode re-
mains active until the read array command (FF16) is written.
completed
Fig. 82 Program flowchart
Table 15 List of software commands (CPU rewrite mode)
First bus cycle
Data
Second bus cycle
Command
Cycle number
Data
to D7)
Mode
Read
Address
Mode
Address
(D0 to D7)
(D0
(Note 4)
Read array
1
2
1
Write
Write
Write
X
FF16
7016
5016
(Note 1)
Read status register
Clear status register
X
X
X
SRD
(Note 2)
(Note 2)
Program
2
2
Write
Write
X
X
4016
2016
Write
Write
WA
WD
(Note 3)
Block erase
BA
D016
Notes 1: SRD = Status Register Data
2: WA = Write Address, WD = Write Data
3: BA = Block Address to be erased (Input the maximum address of each block.)
4: X denotes a given address in the User ROM area.
Rev.1.01 Jan 25, 2005 page 84 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
• Block Erase Command (2016/D016)
By writing the command code “2016” in the first bus cycle and the
confirmation command code “D016” and the block address in the
second bus cycle that follows, the block erase (erase and erase
verify) operation starts for the block address of the flash memory
to be specified.
Start
Write “2016
”
Whether the block erase operation is completed can be confirmed
by read status register or the RY/BY status flag of flash memory
control register. At the same time the block erase operation starts,
the read status register mode is automatically entered, so that the
contents of the status register can be read out. The status register
bit 7 (SR7) is set to “0” at the same time the block erase operation
starts and is returned to “1” upon completion of the block erase
operation. In this case, the read status register mode remains ac-
tive until the read array command (FF16) is written.
“D016
Block address
”
Write
Read status register
SR7 = “1”?
or
RY/BY = “1”?
NO
NO
The RY/BY status flag is “0” during block erase operation and “1”
when the block erase operation is completed as is the status reg-
ister bit 7.
YES
After the block erase ends, erase results can be checked by read-
ing the status register. For details, refer to the section where the
status register is detailed.
Erase error
SR5 = “0” ?
YES
Erase completed
(write read command
“FF16”)
Fig. 83 Erase flowchart
Rev.1.01 Jan 25, 2005 page 85 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀStatus Register
•Erase status (SR5)
The status register shows the operating status of the flash
memory and whether erase operations and programs ended suc-
cessfully or in error. It can be read in the following ways:
(1) By reading an arbitrary address from the User ROM area after
writing the read status register command (7016)
The erase status indicates the operating status of erase operation.
If an erase error occurs, it is set to “1”. When the erase status is
cleared, it is reset to “0”.
•Program status (SR4)
(2) By reading an arbitrary address from the User ROM area in the
period from when the program starts or erase operation starts
to when the read array command (FF16) is input.
The program status indicates the operating status of write opera-
tion. When a write error occurs, it is set to “1”.
The program status is reset to “0” when it is cleared.
Also, the status register can be cleared by writing the clear status
register command (5016).
If “1” is written for any of the SR5 and SR4 bits, the read array,
program, and block erase commands are not accepted. Before ex-
ecuting these commands, execute the clear status register
command (5016) and clear the status register.
After reset, the status register is set to “8016”.
Table 16 shows the status register. Each bit in this register is ex-
plained below.
Also, if any commands are not correct, both SR5 and SR4 are set
to “1”.
•Sequencer status (SR7)
The sequencer status indicates the operating status of the flash
memory. This bit is set to “0” (busy) during write or erase operation
and is set to “1” when these operations ends.
After power-on, the sequencer status is set to “1” (ready).
Table 16 Definition of each bit in status register
Definition
Each bit of
SRD bits
Status name
“1”
“0”
SR7 (bit7)
SR6 (bit6)
SR5 (bit5)
SR4 (bit4)
SR3 (bit3)
SR2 (bit2)
SR1 (bit1)
SR0 (bit0)
Sequencer status
Reserved
Ready
Busy
-
-
Erase status
Program status
Reserved
Terminated in error
Terminated normally
Terminated in error
Terminated normally
-
-
-
-
-
-
-
-
Reserved
Reserved
Reserved
Rev.1.01 Jan 25, 2005 page 86 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀFull Status Check
By performing full status check, it is possible to know the execu-
tion results of erase and program operations. Figure 84 shows a
full status check flowchart and the action to be taken when each
error occurs.
Read status register
YES
SR4 = “1” and
SR5 = “1” ?
Command
sequence error
Execute the clear status register command (5016
to clear the status register. Try performing the
)
operation one more time after confirming that the
command is entered correctly.
NO
NO
NO
Should an erase error occur, the block in error
cannot be used.
Erase error
SR5 = “0” ?
YES
Should a program error occur, the block in error
cannot be used.
Program error
SR4 = “0” ?
YES
End (block erase, program)
Note: When one of SR5 and SR4 is set to “1”, none of the read array, program,
and block erase commands is accepted. Execute the clear status register
command (5016) before executing these commands.
Fig. 84 Full status check flowchart and remedial procedure for errors
Rev.1.01 Jan 25, 2005 page 87 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀ Functions To Inhibit Rewriting Flash
Memory Version
To prevent the contents of internal flash memory from being read
out or rewritten easily, this MCU incorporates a ROM code protect
function for use in parallel I/O mode and an ID code check func-
tion for use in standard serial I/O mode.
If one or both of the pair of ROM code protect bits is set to “0”, the
ROM code protect is turned on, so that the contents of internal
flash memory are protected against readout and modification. The
ROM code protect is implemented in two levels. If level 2 is se-
lected, the flash memory is protected even against readout by a
shipment inspection LSI tester, etc. When an attempt is made to
select both level 1 and level 2, level 2 is selected by default.
If both of the two ROM code protect reset bits are set to “00”, the
ROM code protect is turned off, so that the contents of internal
flash memory can be readout or modified. Once the ROM code
protect is turned on, the contents of the ROM code protect reset
bits cannot be modified in parallel I/O mode. Use the serial I/O or
CPU rewrite mode to rewrite the contents of the ROM code protect
reset bits.
(1) ROM Code Protect Function
The ROM code protect function is the function to inhibit reading
out or modifying the contents of internal flash memory by using
the ROM code protect control address (address FFDB16) in paral-
lel I/O mode. Figure 85 shows the ROM code protect control
address (address FFDB16). (This address exists in the User ROM
area.)
Rewriting of only the ROM code protect control address (address
FFDB16) cannot be performed. When rewriting the ROM code pro-
tect reset bit, rewrite the whole user ROM area (block 0)
containing the ROM code protect control address.
b7
b0
ROM code protect control address (address FFDB16
ROMCP (FF16 when shipped)
)
1 1
Reserved bits (“1” at read/write)
ROM code protect level 2 set bits (ROMCP2) (Notes 1, 2)
b3b2
0 0: Protect enabled
0 1: Protect enabled
1 0: Protect enabled
1 1: Protect disabled
ROM code protect reset bits (ROMCR) (Note 3)
b5b4
0 0: Protect removed
0 1: Protect set bits effective
1 0: Protect set bits effective
1 1: Protect set bits effective
ROM code protect level 1 set bits (ROMCP1) (Note 1)
b7b6
0 0: Protect enabled
0 1: Protect enabled
1 0: Protect enabled
1 1: Protect disabled
Notes 1: When ROM code protect is turned on, the internal flash memory is protected
against readout or modification in parallel I/O mode.
2: When ROM code protect level 2 is turned on, ROM code readout by a shipment
inspection LSI tester, etc. also is inhibited.
3: The ROM code protect reset bits can be used to turn off ROM code protect level 1
and ROM code protect level 2. However, since these bits cannot be modified in
parallel I/O mode, they need to be rewritten in serial I/O mode or CPU rewrite
mode.
Fig. 85 Structure of ROM code protect control address
Rev.1.01 Jan 25, 2005 page 88 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
(2) ID Code Check Function
Use this function in standard serial I/O mode. When the contents
of the flash memory are not blank, the ID code sent from the pro-
grammer is compared with the ID code written in the flash memory
to see if they match. If the ID codes do not match, the commands
sent from the programmer are not accepted. The ID code consists
of 8-bit data, and its areas are FFD416 to FFDA16. Write a pro-
gram which has had the ID code preset at these addresses to the
flash memory.
Address
FFD416
FFD516
FFD616
ID1
ID2
ID3
ID4
ID5
ID6
FFD716
FFD816
FFD916
ID7
FFDA16
FFDB16
ROM code protect control
Interrupt vector area
Fig. 86 ID code store addresses
Rev.1.01 Jan 25, 2005 page 89 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀParallel I/O Mode
The parallel I/O mode is used to input/output software commands,
address and data in parallel for operation (read, program and
erase) to internal flash memory.
Use the external device (writer) only for 3804 Group (spec. H). For
details, refer to the user’s manual of each writer manufacturer.
• User ROM and Boot ROM Areas
In parallel I/O mode, the User ROM and Boot ROM areas shown
in Figure 77 can be rewritten. Both areas of flash memory can be
operated on in the same way.
The Boot ROM area is 4 Kbytes in size and located at addresses
F00016 through FFFF16. Make sure program and block erase op-
erations are always performed within this address range. (Access
to any location outside this address range is prohibited.)
In the Boot ROM area, an erase block operation is applied to only
one 4 Kbyte block. The boot ROM area has had a standard serial
I/O mode control program stored in it when shipped from the fac-tory.
Therefore, using the MCU in standard serial I/O mode, do not
rewrite to the Boot ROM area.
Rev.1.01 Jan 25, 2005 page 90 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ꢀꢀStandard serial I/O Mode
The standard serial I/O mode inputs and outputs the software
commands, addresses and data needed to operate (read, pro-
gram, erase, etc.) the internal flash memory. This I/O is clock
synchronized serial. This mode requires a purpose-specific pe-
ripheral unit.
The standard serial I/O mode is different from the parallel I/O
mode in that the CPU controls flash memory rewrite (uses the
CPU rewrite mode), rewrite data input and so forth. The standard
serial I/O mode is started by connecting “H” to the CNVss pin and
“H” to the P45 (BOOTENT) pin, and releasing the reset operation.
(In the ordinary microcomputer mode, set CNVss pin to “L” level.)
This control program is written in the Boot ROM area when the
product is shipped from Renesas. Accordingly, make note of the
fact that the standard serial I/O mode cannot be used if the Boot
ROM area is rewritten in parallel I/O mode. The standard serial I/
O mode has standard serial I/O mode 1 of the clock synchronous
serial and standard serial I/O mode 2 of the clock asynchronous
serial. Tables 17 and 18 show description of pin function (standard
serial I/O mode). Figures 87 to 90 show the pin connections for
the standard serial I/O mode.
In standard serial I/O mode, only the User ROM area shown in
Figure 77 can be rewritten. The Boot ROM area cannot be written.
In standard serial I/O mode, a 7-byte ID code is used. When there
is data in the flash memory, this function determines whether the
ID code sent from the peripheral unit (programmer) and those writ-
ten in the flash memory match. The commands sent from the
peripheral unit (programmer) are not accepted unless the ID code
matches.
Rev.1.01 Jan 25, 2005 page 91 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 17 Description of pin function (Flash Memory Serial I/O Mode 1)
Pin name
VCC,VSS
Signal name
Power supply
I/O
Function
Apply 2.7 to 5.5 V to the Vcc pin and 0 V to the Vss pin.
After input of port is set, input “H” level.
I
I
I
CNVSS
RESET
CNVSS
Reset input
Reset input pin. To reset the microcomputer, RESET pin should be held at an
“L” level for 16 cycles or more of XIN.
XIN
Clock input
I
Connect an oscillation circuit between the XIN and XOUT pins.
As for the connection method, refer to the “clock generating circuit”.
Connect AVss to Vss.
XOUT
AVSS
VREF
Clock output
O
Analog power supply input
Reference voltage input
I
Apply reference voltage of A/D to this pin.
P00–P07,P10–P17, I/O port
P20–P27,P30–P37,
P40–P43,P50–P57,
P60–P67
I/O
Input “L” or “H” level, or keep open.
P44
P45
P46
P47
RxD input
I
Serial data input pin.
Serial data output pin.
Serial clock input pin.
BUSY signal output pin.
TxD output
SCLK input
BUSY output
O
I
O
Table 18 Description of pin function (Flash Memory Serial I/O Mode 2)
Pin name
VCC,VSS
Signal name
Power supply
I/O
Function
Apply 2.7 to 5.5 V to the Vcc pin and 0 V to the Vss pin.
After input of port is set, input “H” level.
I
I
I
CNVSS
RESET
CNVSS
Reset input
Reset input pin. To reset the microcomputer, RESET pin should be held at an
“L” level for 16 cycles or more of XIN.
XIN
Clock input
I
Connect an oscillation circuit between the XIN and XOUT pins.
As for the connection method, refer to the “clock generating circuit”.
Connect AVss to Vss.
XOUT
AVss
VREF
Clock output
O
Analog power supply input
Reference voltage input
I
Apply reference voltage of A/D to this pin.
P00–P07,P10–P17, I/O port
P20–P27,P30–P37,
P40–P43,P50–P57,
P60–P67
I/O
Input “L” or “H” level, or keep open.
P44
P45
P46
P47
RxD input
I
Serial data input pin.
Serial data output pin.
Input “L” level.
TxD output
SCLK input
BUSY output
O
I
O
BUSY signal output pin.
Rev.1.01 Jan 25, 2005 page 92 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
P20(LED0)
P21(LED1)
P22(LED2)
P23(LED3)
P24(LED4)
P25(LED5)
P26(LED6)
P27(LED7)
P37/SRDY3
P36/SCLK3
P35/TXD3
P34/RXD3
P33/SCL
P32/SDA
P31/DA2
P30/DA1
M38049FFHFP/HP/KP
VSS
VCC
VCC
VREF
VSS
XOUT
ꢀ
XIN
AVSS
P40/INT40/XCOUT
P41/INT00/XCIN
RESET
P67/AN7
P66/AN6
P65/AN5
P64/AN4
P63/AN3
RESET
CNVss
CNVSS
P42/INT1
ꢀ Connect oscillation circuit.
indicates flash memory pin.
RxD
TxD
SCLK
BUSY
Package type: 64P6N-A/64P6Q-A/64P6U-A
Fig. 87 Connection for standard serial I/O mode 1 (M38049FFHFP/HP/KP)
Rev.1.01 Jan 25, 2005 page 93 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
49
50
51
32
31
P20(LED0)
P21(LED1)
P22(LED2)
P23(LED3)
P24(LED4)
P25(LED5)
P26(LED6)
P37/SRDY3
P36/SCLK3
P35/TXD3
P34/RXD3
30
29
28
27
26
25
24
23
22
21
20
19
18
17
52
53
54
55
56
57
58
P33/SCL
P32/SDA
P31/DA2
P30/DA1
P27(LED7)
M38049FFHFP/HP/KP
VCC
VCC
VSS
VSS
XOUT
VREF
AVSS
ꢀ
59
60
XIN
P40/INT40/XCOUT
P41/INT00/XCIN
RESET
P67/AN7
P66/AN6
P65/AN5
P64/AN4
P63/AN3
61
62
63
64
RESET
CNVss
CNVSS
P42/INT1
ꢀ Connect oscillation circuit.
RxD
indicates flash memory pin.
TxD
“L” input
BUSY
Package type: 64P6N-A/64P6Q-A/64P6U-A
Fig. 88 Connection for standard serial I/O mode 2 (M38049FFHFP/HP/KP)
Rev.1.01 Jan 25, 2005 page 94 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
V
CC
V
V
AVSS
/AN
/AN
/AN
CC
1
2
3
4
5
6
7
8
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P3
P3
P3
P3
P3
P3
P3
P3
P0
P0
P0
P0
P0
P0
P0
P0
P1
P1
P1
P1
P1
P1
P1
P1
P2
P2
P2
P2
P2
P2
P2
P2
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
/DA
/DA
/SDA
/SCL
1
2
REF
P6
P6
P6
7
6
5
7
6
5
/R
/T
X
D
3
X
D
3
P6
4
/AN
4
/
S
CLK3
P6
P6
P6
P6
3
2
1
0
/AN
/AN
/AN
/AN
/INT
/PWM
3
2
1
0
3
/
SRDY3
9
/AN
/AN
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
/AN10
/AN11
/AN12
/AN13
/AN14
/AN15
/INT41
/INT01
P5
7
P56
P5
P5
5
4
/CNTR
/CNTR
1
0
P5
P5
P5
P5
CNTR
P4
P4
3
/SRDY2
/SCLK2
/SOUT2
/SIN2
2
1
0
P4
7
/SRDY1
/
2
BUSY
S
CLK
6
/SCLK1
5
/T
/R
X
D
D
1
1
2
1
TXD
P4
P4
P4
4
X
R
X
D
3
/INT
/INT
CNVSS
2
(LED
(LED
(LED
(LED
(LED
(LED
(LED
(LED
0
)
)
)
)
)
)
)
)
CNVSS
1
2
3
4
5
6
7
RESET
/INT00/XCIN
P4 /INT40/XCOUT
RESET
P4
1
0
X
IN
OUT
SS
ꢀ
X
V
SS
V
ꢀ Connect oscillation circuit.
indicates flash memory pin.
Package type: 64P4B
Fig. 89 Connection for standard serial I/O mode 1 (M38049FFHSP)
Rev.1.01 Jan 25, 2005 page 95 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
V
V
AVSS
/AN
/AN
/AN
CC
1
2
3
4
5
6
7
8
V
CC
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P3
P3
P3
P3
P3
P3
P3
P3
P0
P0
P0
P0
P0
P0
P0
P0
P1
P1
P1
P1
P1
P1
P1
P1
P2
P2
P2
P2
P2
P2
P2
P2
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
/DA
/DA
/SDA
/SCL
1
2
REF
P6
P6
P6
7
6
5
7
6
5
/R
/T
X
D
3
X
D
3
P6 /AN4
4
/
S
CLK3
P6
P6
P6
P6
3
2
1
0
/AN
/AN
/AN
/AN
/INT
/PWM
3
2
1
0
3
/
SRDY3
9
/AN
/AN
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
/AN10
/AN11
/AN12
/AN13
/AN14
/AN15
/INT41
/INT01
P5
7
P56
P5
P5
5
4
/CNTR
/CNTR
1
0
P5
P5
P5
P5
CNTR
P4
P4
3
/SRDY2
/SCLK2
/SOUT2
/SIN2
2
1
0
P4
7
/SRDY1
/
2
BUSY
6
/SCLK1
“L” input
5
/T
/R
X
D
D
1
1
2
1
TXD
P4
P4
P4
4
X
RXD
3
/INT
/INT
CNVSS
2
(LED
(LED
(LED
(LED
(LED
(LED
(LED
(LED
0
)
)
)
)
)
)
)
)
CNVSS
1
2
3
4
5
6
7
RESET
RESET
/INT00/XCIN
P4 /INT40/XCOUT
P4
1
0
X
IN
OUT
SS
ꢀ
X
V
SS
V
ꢀ Connect oscillation circuit.
indicates flash memory pin.
Package type: 64P4B
Fig. 90 Connection for standard serial I/O mode 2 (M38049FFHSP)
Rev.1.01 Jan 25, 2005 page 96 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
td(CNVSS-RESET)
td(P4 -RESET)
5
Power source
RESET
CNVSS
P45(TXD)
P46(SCLK)
P47(BUSY)
P44(RXD)
Limits
Notes: In the standard serial I/O mode 1, input “H” to the P4
Be sure to set the CNVss pin to “H” before rising RESET.
Be sure to set the P4 pin to “H” before rising RESET.
6 pin.
Symbol
Unit
Min.
0
Typ. Max.
–
5
–
ms
ms
td(CNVss-RESET)
td(P4 -RESET)
5
0
Fig. 91 Operating waveform for standard serial I/O mode 1
td(CNVSS-RESET)
td(P45-RESET)
Power source
RESET
CNVSS
P45(TXD)
P46(SCLK)
P47(BUSY)
P44
(RX
D)
Limits
Notes: In the standard serial I/O mode 2, input “H” to the P4
Be sure to set the CNVss pin to “H” before rising RESET.
Be sure to set the P4 pin to “H” before rising RESET.
6 pin.
Symbol
Unit
Min.
0
Typ. Max.
5
–
ms
ms
–
td(CNVss-RESET)
td(P4 -RESET)
5
0
Fig. 92 Operating waveform for standard serial I/O mode 2
Rev.1.01 Jan 25, 2005 page 97 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
NOTES ON PROGRAMMING
Serial Interface
In clock synchronous serial I/O, if the receive side is using an ex-
ternal clock and it is to output the SRDY signal, set the transmit
enable bit, the receive enable bit, and the SRDY output enable bit
to “1.”
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1.” Af-
ter a reset, initialize flags which affect program execution. In
particular, it is essential to initialize the index X mode (T) and the
decimal mode (D) flags because of their effect on calculations.
Serial I/O continues to output the final bit from the TXD pin after
transmission is completed. SOUT2 pin for serial I/O2 goes to high
impedance after transfer is completed.
When in serial I/Os 1 and 3 (clock-synchronous mode) or in serial
I/O2, an external clock is used as synchronous clock, write trans-
mission data to the transmit buffer register or serial I/O2 register,
during transfer clock is “H.”
Interrupts
The contents of the interrupt request bits do not change immedi-
ately after they have been written. After writing to an interrupt
request register, execute at least one instruction before perform-
ing a BBC or BBS instruction.
A/D Converter
The comparator uses capacitive coupling amplifier whose charge
will be lost if the clock frequency is too low.
Therefore, make sure that f(XIN) is at least on 500 kHz during an
A/D conversion.
Decimal Calculations
• To calculate in decimal notation, set the decimal mode flag (D)
to “1”, then execute an ADC or SBC instruction. After executing
an ADC or SBC instruction, execute at least one instruction be-
fore executing a SEC, CLC, or CLD instruction.
Do not execute the STP instruction during an A/D conversion.
• In decimal mode, the values of the negative (N), overflow (V),
and zero (Z) flags are invalid.
D/A Converter
The accuracy of the D/A converter becomes rapidly poor under
the VCC = 4.0 V or less condition; a supply voltage of VCC ≥ 4.0 V
is recommended. When a D/A converter is not used, set all values
of D/Ai conversion registers (i=1, 2) to “0016.”
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n+1).
Instruction Execution Time
Multiplication and Division Instructions
• The index X mode (T) and the decimal mode (D) flags do not af-
fect the MUL and DIV instruction.
The instruction execution time is obtained by multiplying the pe-
riod of the internal clock φ by the number of cycles needed to
execute an instruction.
• The execution of these instructions does not change the con-
tents of the processor status register.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
The period of the internal clock φ is double of the XIN period in
high-speed mode.
Ports
The contents of the port direction registers cannot be read. The
following cannot be used:
• The data transfer instruction (LDA, etc.)
• The operation instruction when the index X mode flag (T) is “1”
• The instruction with the addressing mode which uses the value
of a direction register as an index
• The bit-test instruction (BBC or BBS, etc.) to a direction register
• The read-modify-write instructions (ROR, CLB, or SEB, etc.) to
a direction register.
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
Rev.1.01 Jan 25, 2005 page 98 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
NOTES ON USAGE
Handling of Power Source Pins
In order to avoid a latch-up occurrence, connect a capacitor suit-
able for high frequencies as bypass capacitor between power
source pin (VCC pin) and GND pin (VSS pin), and between power
source pin (VCC pin) and analog power source input pin (AVSS
pin). Besides, connect the capacitor to as close as possible. For
bypass capacitor which should not be located too far from the pins
to be connected, a ceramic capacitor of 0.01 µF–0.1 µF is recom-
mended.
Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and may
perform unstable operation.
In a system where the power source voltage drops slowly when
the power source voltage drops or the power supply is turned off,
reset a microcomputer when the power source voltage is less than
the recommended operating conditions and design a system not
to cause errors to the system by this unstable operation.
Flash Memory Version
The CNVss pin determines the flash memory mode. To improve
the noise reduction, connect a track between CNVss pin and Vss
pin or Vcc pin with 1 to 10 kΩ resistance. The mask ROM version
track of CNVss pin has no operational interference even if it is
connected to Vss pin or Vcc pin via a resistor.
Electric Characteristic Differences Between
Mask ROM and Flash Memory Version MCUs
There are differences in electric characteristics, operation margin,
noise immunity, and noise radiation between Mask ROM and
Flash Memory version MCUs due to the difference in the manufac-
turing processes, built-in ROM, and layout pattern etc.When
manufacturing an application system with the Flash Memory ver-
sion and then switching to use of the Mask ROM version, please
conduct evaluations equivalent to the system evaluations con-
ducted for the flash memory version.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM produc-
tion:
ꢀ
1.Mask ROM Confirmation Form
ꢀ
2.Mark Specification Form
3.Data to be written to ROM, in EPROM form (three identical cop-
ies)
ꢀ For the mask ROM confirmation and the mark specifications,
refer to the “Renesas Technology Corp.” Homepage
(http://www.renesas.com/en/rom).
Rev.1.01 Jan 25, 2005 page 99 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
ELECTRICAL CHARACTERISTICS
Absolute maximum ratings
Table 19 Absolute maximum ratings
Symbol
Parameter
Power source voltages
Conditions
Ratings
–0.3 to 6.5
Unit
V
VCC
All voltages are based on Vss.
Output transistors are cut off.
VI
Input voltage P00–P07, P10–P17, P20–P27,
P30, P31, P34–P37, P40–P47,
–0.3 to VCC +0.3
V
P50–P57, P60–P67, VREF
VI
Input voltage P32, P33
–0.3 to 5.8
V
V
V
V
____________
VI
Input voltage RESET, XIN
Input voltage CNVSS
–0.3 to VCC +0.3
–0.3 to VCC +0.3
–0.3 to VCC +0.3
VI
VO
Output voltage P00–P07, P10–P17, P20–P27,
P30, P31, P34–P37, P40–P47,
P50–P57, P60–P67, XOUT
VO
Output voltage P32, P33
Power dissipation
–0.3 to 5.8
1000 (Note)
–20 to 85
V
mW
°C
Pd
Ta = 25°C
Topr
Tstg
Operating temperature
Storage temperature
–65 to 125
°C
Note: This value is 300 mW except SP package.
Rev.1.01 Jan 25, 2005 page 100 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Recommended operating conditions
Table 20 Recommended operating conditions (1)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
5.0
5.0
5.0
5.0
5.0
5.0
0
Symbol
Parameter
Power source voltage
Conditions
Unit
Min.
2.7
2.7
4.0
4.5
2.7
4.5
Max.
5.5
5.5
5.5
5.5
5.5
5.5
When start oscillating (Note 2)
V
V
V
V
V
V
V
V
VCC
High-speed mode
f(XIN) ≤ 8.4 MHz
f(XIN) ≤ 12.5 MHz
f(XIN) ≤ 16.8 MHz
f(XIN) ≤ 12.5 MHz
f(XIN) ≤ 16.8 MHz
(Note 1)
f(φ) = f(XIN)/2
Middle-speed mode
f(φ) = f(XIN)/8
Power source voltage
“H” input voltage
VSS
VIH
VCC
0.8VCC
P00–P07, P10–P17, P20–P27,
P30, P31, P34–P37, P40–P47,
P50–P57, P60–P67
“H” input voltage
5.5
5.5
V
V
0.8VCC
0.7VCC
VIH
VIH
P32, P33
“H” input voltage
2
(when I C-BUS input level is selected)
SDA, SCL
5.5
VIH
VIH
“H” input voltage
(when SMBUS input level is selected)
SDA, SCL
1.4
V
“H” input voltage
VCC
VCC
V
V
V
0.8VCC
____________
RESET, XIN, CNVSS
“H” input voltage
XCIN
VIH
VIL
2
0
“L” input voltage
P00–P07, P10–P17, P20–P27,
P30–P37,P40–P47,
P50–P57, P60–P67
“L” input voltage
0.2VCC
VIL
VIL
0.3Vcc
0.6
V
V
0
0
0
2
(when I C-BUS input level is selected)
SDA, SCL
“L” input voltage
(when SMBUS input level is selected)
SDA, SCL
“L” input voltage
0.2VCC
0.16VCC
0.4
VIL
VIL
VIL
V
V
V
____________
RESET, CNVSS
“L” input voltage
XIN
“L” input voltage
XCIN
Notes 1: When using A/D converter, see A/D converter recommended operating conditions.
2: The start voltage and the start time for oscillation depend on the using oscillator, oscillation circuit constant value and operating
temperature range, etc.. Particularly a high-frequency oscillator might require some notes in the low voltage operation.
Rev.1.01 Jan 25, 2005 page 101 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 21 Recommended operating conditions (2)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Conditions
Symbol
f(XIN)
Parameter
Unit
Min.
Typ.
Max.
(9ꢀVCC-0.3)ꢀ1.05
Main clock input oscillation High-speed mode
MHz
2.7 ≤ VCC < 4.0 V
4.0 ≤ VCC < 4.5 V
3
frequency (Note 1)
f(φ) = f(XIN)/2
(24ꢀVCC-60)ꢀ1.05
MHz
3
16.8
MHz
MHz
4.5 ≤ VCC ≤ 5.5 V
2.7 ≤ VCC < 4.5 V
Middle-speed mode
(15ꢀVCC+39)ꢀ1.1
f(φ) = f(XIN)/8
7
16.8
50
MHz
kHz
4.5 ≤ VCC ≤ 5.5 V
Sub-clock input oscillation
32.768
f(XCIN)
frequency (Notes 1, 2)
Notes 1: When the oscillation frequency has a duty cycle of 50%.
2: When using the microcomputer in low-speed mode, set the sub-clock input oscillation frequency on condition that
f(XCIN) < f(XIN)/3.
Rev.1.01 Jan 25, 2005 page 102 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 22 Recommended operating conditions (3)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
Parameter
–P0 , P1 –P1
Unit
Min.
Max.
–80
–80
80
ΣIOH(peak)
ΣIOH(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOH(avg)
ΣIOH(avg)
ΣIOL(avg)
ΣIOL(avg)
ΣIOL(avg)
IOH(peak)
“H” total peak output current
“H” total peak output current
“L” total peak output current
“L” total peak output current
“L” total peak output current
P0
P40–P47, P50–P57, P60–P67 (Note 1)
P0 –P0 , P1 –P1 , P3 –P3 (Note 1)
P20–P27 (Note 1)
P40–P47,P50–P57, P60–P67 (Note 1)
–P0 , P1 –P1 , P2 –P2 , P3 , P3 , P3
“H” total average output current P40–P47,P50–P57, P60–P67 (Note 1)
“L” total average output current P0 –P0 , P1 –P1 , P3 –P3 (Note 1)
“L” total average output current P20–P27 (Note 1)
“L” total average output current P40–P47,P50–P57, P60–P67 (Note 1)
0
7
0
7
, P2
0
–P2
7
, P3
0
, P3
1
, P3
4
–P3
7
7
(Note 1)
(Note 1)
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
0
7
0
7
0
7
80
80
“H” total average output current P0
0
7
0
7
0
7
0
1
4
–P3
–40
–40
40
0
7
0
7
0
7
40
40
“H” peak output current
P00–P07, P10–P17, P20–P27, P30, P31, P34–P37,
P40–P47, P50–P57, P60–P67 (Note 2)
–10
IOL(peak)
“L” peak output current
P00–P07, P10–P17, P30–P37, P40–P47, P50–P57,
P60–P67 (Note 2)
10
mA
IOL(peak)
IOH(avg)
“L” peak output current
P20–P27 (Note 2)
20
mA
mA
“H” average output current
P00–P07, P10–P17, P20–P27, P30, P31, P34–P37,
P40–P47, P50–P57, P60–P67 (Note 3)
–5
IOL(avg)
IOL(avg)
“L” average output current
“L” average output current
P00–P07, P10–P17, P30–P37, P40–P47, P50–P57,
P60–P67 (Note 3)
5
mA
mA
P20–P27 (Note 3)
10
Notes 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an aver-
age value measured over 100 ms. The total peak current is the peak value of all the currents.
2: The peak output current is the peak current flowing in each port.
3: The average output current IOL(avg), IOH(avg) are average value measured over 100 ms.
Rev.1.01 Jan 25, 2005 page 103 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Electrical characteristics
Table 23 Electrical characteristics (1)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
Parameter
“H” output voltage
P00–P07, P10–P17, P20–P27,
P30, P31, P34–P37, P40–P47,
P50–P57, P60–P67 (Note 1)
Test conditions
IOH = –10 mA
VCC = 4.0 to 5.5 V
IOH = –1.0 mA
Unit
Min.
Max.
VOH
VOL
VOL
VCC–2.0
V
V
VCC–1.0
VCC = 1.8 to 5.5 V
“L” output voltage
IOL = 10 mA
VCC = 4.0 to 5.5 V
IOL = 1.6 mA
2.0
1.0
V
V
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
P60–P67
VCC = 1.8 to 5.5 V
“L” output voltage
P20–P27
IOL = 20 mA
VCC = 4.0 to 5.5 V
IOL = 1.6 mA
2.0
0.4
V
V
VCC = 1.8 to 5.5 V
VT+–VT–
VT+–VT–
Hysteresis
CNTR0, CNTR1, CNTR2,
INT0–INT4
0.4
0.5
0.5
V
V
Hysteresis
RxD1, SCLK1, SIN2, SCLK2, RxD3,
SCLK3
____________
VT+–VT–
Hysteresis RESET
V
IIH
“H” input current
VI = VCC
5.0
µA
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
(Pin floating. Pull-up
transistors “off”)
P60–P67
____________
IIH
IIH
IIL
“H” input current RESET, CNVSS
“H” input current XIN
VI = VCC
VI = VCC
5.0
µA
µA
µA
4.0
“L” input current
VI = VSS
–5.0
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P47, P50–P57,
(Pin floating. Pull-up
transistors “off”)
P60–P67
____________
IIL
IIL
IIL
“L” input current RESET,CNVSS
VI = VSS
VI = VSS
–5.0
µA
µA
µA
“L” input current
XIN
–4.0
“L” input current (at Pull-up)
P00–P07, P10–P17, P20–P27,
P30, P31, P34–P37, P40–P47,
P50–P57, P60–P67
VI = VSS
VCC = 5.0 V
VI = VSS
–80
–30
–210
–420
–140
–70
µA
VCC = 3.0 V
VRAM
RAM hold voltage
When clock stopped
1.8
VCC
V
Note 1: P35 is measured when the P35/TxD3 P-channel output disable bit of the UART3 control register (bit 4 of address 003316) is “0”.
P45 is measured when the P45/TxD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is “0”.
Rev.1.01 Jan 25, 2005 page 104 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 24 Electrical characteristics (2)
(VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, f(XCIN)=32.768kHZ (Stoped in middle-speed mode), Output transistors “off”,
AD converter not operated)
Limits
Unit
Symbol
ICC
Parameter
Test conditions
f(XIN) = 16.8 MHz
Max.
Typ.
Min.
Power source
current
High-speed
mode
VCC = 5V
5.5
4.5
3.5
2.2
2.2
2.7
1.8
1.1
3.0
2.4
2.0
2.1
1.7
1.5
1.3
410
4.5
400
3.7
0.55
0.75
1000
8,3
6.8
5.3
3.3
3.3
4.1
2.7
1.7
4.5
3.6
3.0
3.2
2.6
2.3
2.0
630
6.8
600
5.6
3.0
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
µA
f(XIN) = 12.5 MHz
f(XIN) = 8.4 MHz
f(XIN) = 4.2 MHz
f(XIN) = 16.8 MHz (in WIT state)
f(XIN) = 8.4 MHz
f(XIN) = 4.2 MHz
f(XIN) = 2.1 MHz
f(XIN) = 16.8 MHz
f(XIN) = 12.5 MHz
f(XIN) = 8.4 MHz
f(XIN) = 16.8 MHz (in WIT state)
f(XIN) = 12.5 MHz
f(XIN) = 8.4 MHz
f(XIN) = 6.3 MHz
f(XIN) = stopped
In WIT state
VCC = 3V
VCC = 5V
Middle-speed
mode
VCC = 3V
Low-speed
mode
VCC = 5V
VCC = 3V
µA
f(XIN) = stopped
In WIT state
µA
µA
In STP state
(All oscillation stopped)
Ta = 25 °C
µA
Ta = 85 °C
µA
Increment when A/D conversion
is executed
f(XIN) = 16.8 MHz, VCC = 5V
In Middle-, high-speed mode
µA
Rev.1.01 Jan 25, 2005 page 105 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
A/D converter characteristics
Table 25 A/D converter recommended operating conditions
(VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V,Ta = –20 to 85 °C, unless otherwise noted)
Limits
Unit
V
Conditions
8-bit A/D mode (Note 1)
Symbol
VCC
Parameter
Max.
Min.
Typ.
5.0
5.0
Power source voltage
2.7
2.7
2.0
5.5
5.5
VCC
(When A/D converter is used)
Analog reference voltage
Analog power source voltage
Analog input voltage
10-bit A/D mode (Note 2)
V
V
V
VREF
AVSS
VIA
0
0
VCC
MHZ
Main clock oscillation frequency
2.7 ≤ VCC < 4.0 V
4.0 ≤ VCC < 4.5 V
4.5 ≤ VCC ≤ 5.5 V
0.5
(9ꢀVCC-0.3)ꢀ1.05
f(XIN)
3
(When A/D converter is used)
0.5
0.5
(24ꢀVCC-60)ꢀ1.05
3
16.8
Note 1: 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”.
2: 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”.
Table 26 A/D converter characteristics
(VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Unit
Parameter
Test conditions
Min.
Typ.
Max.
–
Resolution
8-bit A/D mode (Note 1)
10-bit A/D mode (Note 2)
8
10
±2
±4
50
61
100
200
5
bit
–
Absolute accuracy
(excluding quantization error)
Conversion time
8-bit A/D mode (Note 1) 2.7 ≤ VREF ≤ 5.5 V
10-bit A/D mode (Note 2) 2.7 ≤ VREF ≤ 5.5 V
8-bit A/D mode (Note 1)
LSB
tCONV
2tc(XIN)
10-bit A/D mode (Note 2)
RLADDER Ladder resistor
12
50
35
kΩ
µA
µA
µA
IVREF
Reference power
atA/D converter operated VREF = 5.0 V
150
source input current atA/D converter stopped VREF = 5.0 V
A/D port inout current
II(AD)
5
Note 1: 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”.
2: 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”.
D/A converter characteristics
Table 27 D/A converter characteristics
(VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Parameter
Test conditions
Unit
Min.
Typ.
Max.
–
–
Resolution
Absolute accuracy
8
1.0
2.5
3
bit
%
4.0 ≤ VREF ≤ 5.5 V
2.7 ≤ VREF < 4.0 V
%
tsu
RO
Setting time
Output resistor
µs
kΩ
mA
2
3.5
5
IVREF
Reference power source input current (Note 1)
3.2
Note 1: Using one D/A converter, with the value in the DA conversion register of the other D/A converter being “0016”.
Power source circuit timing characteristics
Table 28 Power source circuit timing characteristics
(VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
td(P–R)
Parameter
Test conditions
Unit
ms
Min.
Max.
2
Internal power source stable time at power-on
2.7 ≤ Vcc < 5.5 V
Rev.1.01 Jan 25, 2005 page 106 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Timing requirements and switching characteristics
Table 29 Timing requirements (1)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Symbol
Parameter
Unit
Typ.
Min.
Max.
tW(RESET)
tC(XIN)
Reset input “L” pulse width
Main clock XIN
XIN cycle
ns
td(P-R) ms + 16
59.5
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
input cycle time
10000/(86VCC-219)
26ꢀ103/(82VCC-3)
tWH(XIN)
tWL(XIN)
Main clock XIN
ns
ns
25
input “H” pulse width
4000/(86VCC-219)
10000/(82VCC-3)
Main clock XIN
25
input “L” pulse width
4000/(86VCC-219)
10000/(82VCC-3)
tC(XCIN)
Sub-clock XCIN input cycle time
Sub-clock XCIN input “H” pulse width
Sub-clock XCIN input “L” pulse width
CNTR0–CNTR2
µs
µs
µs
ns
20
5
tWH(XCIN)
tWL(XCIN)
tC(CNTR)
5
120
160
250
48
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
input cycle time
tWH(CNTR)
tWL(CNTR)
tWH(INT)
CNTR0–CNTR2
ns
ns
ns
ns
input “H” pulse width
64
115
48
CNTR0–CNTR2
input “L” pulse width
64
115
48
INT00, INT01, INT1, INT2, INT3, INT40, INT41
input “H” pulse width
64
115
48
tWL(INT)
INT00, INT01, INT1, INT2, INT3, INT40, INT41
input “L” pulse width
64
115
Rev.1.01 Jan 25, 2005 page 107 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 30 Timing requirements (2)
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Typ.
Symbol
Parameter
Unit
ns
Min.
250
320
500
120
150
240
120
150
240
70
Max.
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
t
t
t
C(SCLK1), tC(SCLK3)
Serial I/O1, serial I/O3
clock input cycle time (Note)
ns
ns
ns
ns
ns
ns
ns
ns
ns
WH(SCLK1), tWH(SCLK3
)
Serial I/O1, serial I/O3
clock input “H” pulse width (Note)
WL(SCLK1), tWL(SCLK3
)
Serial I/O1, serial I/O3
clock input “L” pulse width (Note)
tsu(RxD1-SCLK1),
tsu(RxD3-SCLK3)
Serial I/O1, serial I/O3
clock input setup time
90
100
32
th(SCLK1-RxD1),
th(SCLK3-RxD3)
Serial I/O1, serial I/O3
clock input hold time
40
50
500
650
1000
200
260
400
200
260
400
100
130
200
100
130
150
tC(SCLK2)
Serial I/O2
clock input cycle time
tWH(SCLK2)
tWL(SCLK2)
Serial I/O2
clock input “H” pulse width
Serial I/O2
clock input “L” pulse width
tsu(SIN2-SCLK2)
th(SCLK2-SIN2)
Serial I/O2
clock input setup time
Serial I/O2
clock input hold time
Note : When bit 6 of address 001A16 and bit 6 of address 003216 are “1” (clock synchronous).
Divide this value by four when bit 6 of address 001A16 and bit 6 of address 003216 are “0” (UART).
Rev.1.01 Jan 25, 2005 page 108 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 31 Switching characteristics
(VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted)
Limits
Test
conditions
Symbol
Parameter
Serial I/O1, serial I/O3
Unit
ns
Min.
Typ.
Max.
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
4.5≤VCC≤5.5 V
4.0≤VCC<4.5 V
2.7≤VCC<4.0 V
tC(SCLK1)2-30, tC(SCLK3)/2-30
tC(SCLK1)2-35, tC(SCLK3)/2-35
tC(SCLK1)2-40, tC(SCLK3)/2-40
tC(SCLK1)2-30, tC(SCLK3)/2-30
tC(SCLK1)2-35, tC(SCLK3)/2-35
tC(SCLK1)2-40, tC(SCLK3)/2-40
t
t
WH(SCLK1
WH(SCLK3
)
)
clock output “H” pulse width
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
t
WL(SCLK1
WL(SCLK3
)
Serial I/O1, serial I/O3
)
clock output “L” pulse width
140
200
350
td(
td(
S
CLK1-TxD1)
CLK3-TxD3)
Serial I/O1, serial I/O3
S
output delay time (Note)
-30
-30
-30
tV(
tV(
S
CLK1-TxD1)
CLK3-TxD3)
Serial I/O1, serial I/O3
S
output valid time (Note)
30
35
40
30
35
40
tr(SCLK1)
tr(SCLK3)
Serial I/O1, serial I/O3
rise time of clock output
tf(SCLK1)
tf(SCLK3)
Serial I/O1, serial I/O3
fall time of clock output
Fig. 93
tC(SCLK2)/2-160
tC(SCLK2)/2-200
tC(SCLK2)/2-240
tC(SCLK2)/2-160
tC(SCLK2)/2-200
tC(SCLK2)/2-240
tWH(SCLK2)
tWL(SCLK2)
Serial I/O2
clock output “H” pulse width
Serial I/O2
clock output “L” pulse width
200
250
300
td(SCLK2-SOUT2)
Serial I/O2
output delay time
0
0
0
tV(SCLK2-SOUT2)
Serial I/O2
output valid time
30
35
40
30
35
40
30
35
40
t
t
t
f
(SCLK2
)
Serial I/O2
fall time of clock output
10
12
15
10
12
15
r
(CMOS)
CMOS
rise time of output (Note)
f
(CMOS)
CMOS
fall time of output (Note)
Note: When the P45/TxD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is “0”.
Rev.1.01 Jan 25, 2005 page 109 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Measurement output pin
1kΩ
Measurement output pin
100pF
100pF
CMOS output
N-channel open-drain output
Fig.93 Circuit for measuring output switching characteristics (1)
Fig.94 Circuit for measuring output switching characteristics (2)
Rev.1.01 Jan 25, 2005 page 110 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Single-chip mode timing diagram
t
C(CNTR)
t
WL(CNTR)
t
WH(CNTR)
0.8VCC
CNTR0, CNTR1, CNTR2
0.2VCC
0.2VCC
t
WL(INT)
t
WH(INT)
INT1,INT2,INT
3
0.8VCC
INT00,INT40
INT01,INT41
t
W(RESET)
0.8VCC
RESET
0.2VCC
t
t
C(XIN)
t
t
WL(XIN)
t
WH(XIN)
0.8VCC
X
IN
0.2VCC
0.2VCC
C(XCIN
)
WL(XCIN
)
t
WH(XCIN)
0.8VCC
X
CIN
t
C(SCLK1),
WL(SCLK3
t
C(SCLK2),
t
C(SCLK3),
t
f
t
WL(SCLK1),
t
WL(SCLK2),
t
)
t
WH(SCLK1), WH(SCLK2), tWH(SCLK3)
t
t
r
S
S
S
CLK1
CLK2
CLK3
0.8VCC
0.2VCC
t
t
t
su(R
su(SIN2-
su(R D3
x
D1
S
-
-
S
CLK1),
t
t
t
h(SCLK1-
h(SCLK2-
h(SCLK3-
R
S
R
x
D1),
IN2),
D3)
CLK2),
x
S
CLK3
)
x
R
X
X
IN2
D
1
3
0.8V
0.2VCCCC
R
D
S
t
t
t
v
v
v
(SCLK1-T
(SCLK2-SOUT2),
(SCLK3-T D3)
xD1),
t
d(SCLK1-T
x
D1), td(SCLK2-SOUT2), td(SCLK3-TxD3)
x
T
T
X
X
OUT2
D
1
3
D
S
Fig. 95 Timing diagram (in single-chip mode)
Rev.1.01 Jan 25, 2005 page 111 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
Table 32 Multi-master I2C-BUS bus line characteristics
Standard clock mode High-speed clock mode
Symbol
Parameter
Unit
Min.
4.7
Max.
Max.
Min.
1.3
tBUF
µs
µs
µs
ns
µs
µs
ns
ns
µs
µs
Bus free time
tHD;STA
tLOW
Hold time for START condition
Hold time for SCL clock = “0”
Rising time of both SCL and SDA signals
Data hold time
0.6
1.3
4.0
4.7
tR
20+0.1Cb
0
300
0.9
1000
300
tHD;DAT
tHIGH
tF
0
Hold time for SCL clock = “1”
Falling time of both SCL and SDA signals
Data setup time
0.6
4.0
20+0.1Cb
100
300
tSU;DAT
tSU;STA
tSU;STO
250
4.7
4.0
Setup time for repeated START condition
Setup time for STOP condition
0.6
0.6
Note: Cb = total capacitance of 1 bus line
SDA
t
HD:STA
tsu:STO
t
BUF
t
LOW
t
R
t
F
S
P
Sr
P
SCL
t
HD:DAT
t
HD:STA
t
HIGH
tsu:DAT
t
su:STA
S : START condition
Sr: RESTART condition
P : STOP condition
Fig. 96 Timing diagram of multi-master I2C-BUS
Rev.1.01 Jan 25, 2005 page 112 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
PACKAGE OUTLINE
64P6N-A
Plastic 64pin 14ꢀ14mm body QFP
EIAJ Package Code
QFP64-P-1414-0.80
JEDEC Code
Weight(g)
1.11
Lead Material
Alloy 42
–
MD
HD
D
64
49
1
48
I2
Recommended Mount Pad
Dimension in Millimeters
Symbol
Min
–
0
–
0.3
0.13
13.8
13.8
–
16.5
16.5
0.4
–
Nom
–
Max
3.05
0.2
–
0.45
0.2
14.2
14.2
–
17.1
17.1
0.8
–
0.1
10°
–
A
A1
A2
b
c
D
0.1
2.8
0.35
0.15
14.0
14.0
0.8
16.8
16.8
0.6
1.4
–
–
0.5
–
14.6
14.6
16
33
A
E
e
17
32
L1
HD
HE
L
L1
y
–
0°
–
1.3
–
F
e
b
b2
I2
MD
ME
L
–
–
–
y
Detail F
–
64P4B
Plastic 64pin 750mil SDIP
EIAJ Package Code
JEDEC Code
Weight(g)
Lead Material
SDIP64-P-750-1.78
–
7.9
Alloy 42/Cu Alloy
64
33
1
32
Dimension in Millimeters
Symbol
Min
–
0.38
–
Nom
–
–
Max
5.08
–
D
A
A1
A2
b
b1
b2
c
D
E
e
e1
3.8
–
0.4
0.9
0.65
0.2
56.2
16.85
–
–
2.8
0°
0.5
1.0
0.59
1.3
1.05
0.32
56.6
17.15
–
–
–
15°
0.75
0.25
56.4
17.0
1.778
19.05
–
e
b1
b
b2
SEATING PLANE
L
–
Rev.1.01 Jan 25, 2005 page 113 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
64P6Q-A
Plastic 64pin 10✕10mm body LQFP
EIAJ Package Code
LQFP64-P-1010-0.5
JEDEC Code
Weight(g)
Lead Material
Cu Alloy
MD
—
HD
D
48
33
I2
Recommended Mount Pad
49
32
Dimension in Millimeters
Symbol
Min
—
0
Nom
—
0.1
Max
1.7
0.2
—
0.28
0.175
10.1
10.1
—
A
A1
A2
b
c
D
—
1.4
0.13
0.105
9.9
9.9
—
0.18
0.125
10.0
10.0
0.5
64
17
E
e
1
16
A
HD
HE
L
L1
Lp
A3
x
11.8
11.8
0.3
—
0.45
—
—
—
0¡
—
12.0
12.0
0.5
1.0
0.6
0.25
—
—
—
0.225
—
12.2
12.2
0.7
—
0.75
—
0.08
0.1
10¡
—
F
e
L1
y
y
L
b
b2
I2
MD
ME
x
M
Lp
1.0
—
—
—
—
—
Detail F
10.4
10.4
64P6U-A
Plastic 64pin 14ꢀ14mm body LQFP
EIAJ Package Code
LQFP64-P-1414-0.8
JEDEC Code
Weight(g)
Lead Material
Cu Alloy
—
MD
HD
D
48
33
l2
49
32
Recommended Mount Pad
Dimension in Millimeters
Symbol
Min
—
0
Nom
—
0.1
Max
1.7
0.2
—
0.45
0.175
14.1
14.1
—
A
A1
A2
b
c
D
—
1.4
0.32
0.105
13.9
13.9
—
0.37
0.125
14.0
14.0
0.8
64
17
E
e
1
16
A
16.0
16.0
0.5
1.0
0.6
0.25
—
—
—
0.5
HD
HE
L
L1
Lp
A3
x
15.8
15.8
0.3
—
0.45
—
—
—
0¡
—
16.2
16.2
0.7
—
0.75
—
0.2
0.1
8¡
—
—
—
—
L1
F
e
L
b
y
y
M
x
Lp
b2
I2
MD
ME
0.95
—
—
—
14.4
14.4
Detail F
Rev.1.01 Jan 25, 2005 page 114 of 114
REJ03B0131-0101Z
3804 Group (Spec.H) Data Sheet
REVISION HISTORY
Rev.
Date
Description
Summary
Page
1.00 Dec.10, 2004
1.01 Jan.25, 2005
–
First edition issued
2
Fig.1, 2 pin configurations are partly revised. P32→P32/SDA, P33→P33/SCL
11
“ (2) Bits 1, 2, 3 of address 001016: Middle-speed Mode Automatic Switch Func-
tion” is partly revised.
“●Middle-speed mode automatic switch by SCL/SDA Interrupt” is added.
Note 2 of Fig.9 is added.
22
INTERRUPTS is partly revised.
●Note is partly added.
●Precautoins of “ (3) Pulse output mode” is partly revised.
●Precautoins of “ (6) Programmable waveform generating mode” is partly re-
31
33
vised.
●Precautoins of “ (7) Programmable one-shot generating mode” is partly re-
vised.
93,94,95,96 Fig.87, 88, 89, 90 are partly revised. P32→P32/SDA, P33→P33/SCL
(1/1)
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits,
(ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
RENESAS SALES OFFICES
http://www.renesas.com
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .2.0
相关型号:
©2020 ICPDF网 联系我们和版权申明