X5323S8IZ-T [RENESAS]
IC,SERIAL EEPROM,4KX8,CMOS,SOP,8PIN,PLASTIC;型号: | X5323S8IZ-T |
厂家: | RENESAS TECHNOLOGY CORP |
描述: | IC,SERIAL EEPROM,4KX8,CMOS,SOP,8PIN,PLASTIC 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 |
文件: | 总20页 (文件大小:341K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
X5323, X5325
®
(Replaces X25323, X25325)
Data Sheet
June 30, 2008
FN8131.2
CPU Supervisor with 32kBit SPI EEPROM
Features
These devices combine four popular functions, Power-on
Reset Control, Watchdog Timer, Supply Voltage Supervision,
and Block Lock Protect Serial EEPROM Memory in one
package. This combination lowers system cost, reduces
board space requirements, and increases reliability.
• Selectable watchdog timer
• Low VCC detection and reset assertion
- Five standard reset threshold voltages
- Re-program low VCC reset threshold voltage using
special programming sequence
Applying power to the device activates the power-on reset
circuit which holds RESET/RESET active for a period of
time. This allows the power supply and oscillator to stabilize
before the processor can execute code.
- Reset signal valid to VCC = 1V
• Determine watchdog or low voltage reset with a volatile
flag bit
• Long battery life with low power consumption
- <50µA max standby current, watchdog on
- <1µA max standby current, watchdog off
- <400µA max active current during read
The Watchdog Timer provides an independent protection
mechanism for microcontrollers. When the microcontroller
fails to restart a timer within a selectable time out interval,
the device activates the RESET/RESET signal. The user
selects the interval from three preset values. Once selected,
the interval does not change, even after cycling the power.
• 32kbits of EEPROM
• Built-in inadvertent write protection
- Power-up/power-down protection circuitry
- Protect 0, 1/4, 1/2 or all of EEPROM array with Block
Lock™ protection
The device’s low VCC detection circuitry protects the user’s
system from low voltage conditions, resetting the system
when VCC falls below the minimum VCC trip point.
RESET/RESET is asserted until VCC returns to proper
operating level and stabilizes. Five industry standard VTRIP
thresholds are available, however, Intersil’s unique circuits
allow the threshold to be reprogrammed to meet custom
requirements or to fine-tune the threshold for applications
requiring higher precision.
- In circuit programmable ROM mode
• 2MHz SPI interface modes (0,0 and 1,1)
• Minimize EEPROM programming time
- 32-byte page write mode
- Self-timed write cycle
- 5ms write cycle time (typical)
• 2.7V to 5.5V and 4.5V to 5.5V power supply
operation
• Available packages
- 14 Ld TSSOP, 8 Ld SOIC, 8 Ld PDIP
• Pb-free (RoHS compliant)
Block Diagram
WATCHDOG TRANSITION
DETECTOR
WATCHDOG
TIMER RESET
WP
PROTECT LOGIC
RESET/RESET
X5323 = RESET
SI
DATA
REGISTER
STATUS
REGISTER
SO
RESET AND
WATCHDOG
TIMEBASE
COMMAND
DECODE AND
CONTROL
LOGIC
X5325 = RESET
SCK
8kBITS
8kBITS
CS/WDI
V
THRESHOLD
RESET LOGIC
CC
16kBITS
POWER-ON AND
LOW VOLTAGE
RESET
V
+
-
CC
GENERATION
V
TRIP
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005, 2008. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.
X5323, X5325
Ordering Information
PART NUMBER
PART NUMBER
RESET
RESET
PART
PART
MARKING
V
CC RANGE
(V)
TEMP
(ACTIVE LOW)
MARKING
(ACTIVE HIGH)
V
TRIP RANGE RANGE (°C)
PACKAGE
8 Ld PDIP
8 Ld PDIP** (Pb-free)
X5323P-4.5A
X5323P AL
X5325P-4.5A
X5325P AL
X5325P ZAL
X5325P AM
X5325P ZAM
X5325 AL
4.5 to 5.5
4.5 to 4.75
0 to +70
0 to +70
X5323PZ-4.5A (Note) X5323P ZAL X5325PZ-4.5A
X5323PI-4.5A X5323P AM X5325PI-4.5A
X5323PIZ-4.5A (Note) X5323P ZAM X5325PIZ-4.5A
X5323S8-4.5A X5323 AL X5325S8-4.5A
X5323S8Z-4.5A (Note) X5323 ZAL
-40 to +85 8 Ld PDIP
-40 to +85 8 Ld PDIP** (Pb-free)
0 to +70
0 to +70
8 Ld SOIC
X5325S8Z-4.5A (Note) X5325 ZAL
8 Ld SOIC (Pb-free)
X5323S8I-4.5A*
X5323 AM
X5325S8I-4.5A
X5325 AM
-40 to +85 8 Ld SOIC
X5323S8IZ-4.5A*
(Note)
X5323 ZAM X5325S8IZ-4.5A
(Note)
X5325 ZAM
-40 to +85 8 Ld SOIC (Pb-free)
X5323V14-4.5A
X5323 VAL
X5325V14-4.5A
X5325 VAL
0 to +70
0 to +70
14 Ld TSSOP
X5323V14Z-4.5A
(Note)
X5323 VZAL X5325V14Z-4.5A
(Note)
X5325 VZAL
14 Ld TSSOP
(Pb-free)
X5323V14I-4.5A
X5323 VAM X5325V14I-4.5A
X5325 VAM
-40 to +85 14 Ld TSSOP
X5323V14IZ-4.5A
(Note)
X5323 VZAM X5325V14IZ-4.5A
(Note)
X5325 VZAM
-40 to +85 14 Ld TSSOP
(Pb-free)
X5323P
X5323P
X5325P
X5325P
4.5 to 5.5
4.25 to 4.5
0 to +70
0 to +70
8 Ld PDIP
X5323PZ (Note)
X5323PI
X5323P Z
X5323P I
X5323P ZI
X5323
X5325PZ
X5325P Z
X5325P I
X5325P ZI
X5325
8 Ld PDIP** (Pb-free)
X5325PI
-40 to +85 8 Ld PDIP
X5323PIZ (Note)
X5323S8*
X5325PIZ
-40 to +85 8 Ld PDIP** (Pb-free)
X5325S8*
0 to +70
0 to +70
8 Ld SOIC
X5323S8Z* (Note)
X5323S8I*
X5323 Z
X5323 I
X5325S8Z* (Note)
X5325S8I*
X5325 Z
X5325 I
8 Ld SOIC (Pb-free)
-40 to +85 8 Ld SOIC
X5323S8IZ* (Note)
X5323V14*
X5323 ZI
X5323 V
X5323 VZ
X5325S8IZ* (Note)
X5325V14*
X5325 ZI
X5325 V
X5325 VZ
-40 to +85 8 Ld SOIC (Pb-free)
0 to +70
0 to +70
14 Ld TSSOP
X5323V14Z* (Note)
X5325V14Z* (Note)
14 Ld TSSOP
(Pb-free)
X5323V14I*
X5323 VI
X5325V14I*
X5325 VI
-40 to +85 14 Ld TSSOP
X5323V14IZ* (Note)
X5323 VZI
X5325V14IZ* (Note)
X5325 VZI
-40 to +85 14 Ld TSSOP
(Pb-free)
X5323P-2.7A
X5323P AN
X5325P-2.7A
X5325P AN
X5325P ZAN
X5325P AP
X5325P ZAP
X5325 AN
2.7 to 5.5
2.85 to 3.0
0 to +70
0 to +70
8 Ld PDIP
X5323PZ-2.7A (Note) X5323P ZAN X5325PZ-2.7A
X5323PI-2.7A X5323P AP X5325PI-2.7A
X5323PIZ-2.7A (Note) X5323P ZAP X5325PIZ-2.7A
8 Ld PDIP** (Pb-free)
-40 to +85 8 Ld PDIP
-40 to +85 8 Ld PDIP** (Pb-free)
X5323S8-2.7A*
X5323 AN
X5325S8-2.7A
0 to +70
0 to +70
8 Ld SOIC
X5323S8Z-2.7A*
(Note)
X5323 ZAN
X5325S8Z-2.7A (Note) X5325 ZAN
8 Ld SOIC (Pb-free)
X5323S8I-2.7A*
X5323 AP
X5325S8I-2.7A
X5325 AP
-40 to +85 8 Ld SOIC
X5323S8IZ-2.7A*
(Note)
X5323 ZAP
X5325S8IZ-2.7A
(Note)
X5325 ZAP
-40 to +85 8 Ld SOIC (Pb-free)
FN8131.2
June 30, 2008
2
X5323, X5325
Ordering Information (Continued)
PART NUMBER
RESET
(ACTIVE LOW)
PART NUMBER
RESET
(ACTIVE HIGH)
PART
MARKING
PART
MARKING
V
CC RANGE
(V)
TEMP
V
TRIP RANGE RANGE (°C)
PACKAGE
X5323V14-2.7A
X5323 VAN
X5325V14-2.7A
X5325 VAN
2.7 to 5.5
2.85 to 3.0
0 to +70
0 to +70
14 Ld TSSOP
X5323V14Z-2.7A
(Note)
X5323 VZAN X5325V14Z-2.7A
(Note)
X5325 VZAN
14 Ld TSSOP
(Pb-free)
X5323V14I-2.7A
X5323 VAP
X5325V14I-2.7A
X5325 VAP
-40 to +85 14 Ld TSSOP
X5323V14IZ-2.7A
(Note)
X5323 VZAP X5325V14IZ-2.7A
(Note)
X5325 VZAP
-40 to +85 14 Ld TSSOP
(Pb-free)
X5323P-2.7
X5323P F
X5323P ZF
X5323P G
X5323P ZG
X5323 F
X5325P-2.7
X5325P F
X5325P ZF
X5325P G
X5325P ZG
X5325 F
2.7 to 5.5
2.55 to 2.7
0 to +70
0 to +70
8 Ld PDIP
X5323PZ-2.7 (Note)
X5323PI-2.7
X5325PZ-2.7
X5325PI-2.7
X5325PIZ-2.7
X5325S8-2.7*
8 Ld PDIP** (Pb-free)
-40 to +85 8 Ld PDIP
X5323PIZ-2.7 (Note)
X5323S8-2.7*
-40 to +85 8 Ld PDIP** (Pb-free)
0 to +70
0 to +70
8 Ld SOIC
X5323S8Z-2.7* (Note) X5323 ZF
X5323S8I-2.7* X5323 G
X5323S8IZ-2.7* (Note) X5323 ZG
X5325S8Z-2.7* (Note) X5325 ZF
X5325S8I-2.7* X5325 G
X5325S8IZ-2.7* (Note) X5325 ZG
8 Ld SOIC (Pb-free)
-40 to +85 8 Ld SOIC
-40 to +85 8 Ld SOIC (Pb-free)
X5323V14-2.7*
X5323 VF
X5325V14-2.7*
X5325 VF
0 to +70
0 to +70
14 Ld TSSOP
X5323V14Z-2.7*
(Note)
X5323 VZF
X5325V14Z-2.7*
(Note)
X5325 VZF
14 Ld TSSOP
(Pb-free)
X5323V14I-2.7*
X5323 VG
X5325V14I-2.7*
X5325 VG
-40 to +85 14 Ld TSSOP
X5323V14IZ-2.7*
(Note)
X5323 VZG
X5325V14IZ-2.7*
(Note)
X5325 VZG
-40 to +85 14 Ld TSSOP
(Pb-free)
*Add “-T1” for tape and reel. Please refer to TB347 for details on reel specifications.
**Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100%
matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-
020.
Pinouts
X5323, X5325
(8 LD SOIC, PDIP)
TOP VIEW
X5323, X5325
(14 LD TSSOP)
TOP VIEW
1
2
14
13
12
V
CS/WDI
SO
1
8
V
CC
CS/WDI
SO
CC
RESET/RESET
2
3
7
6
RESET/RESET
3
4
5
NC
NC
NC
WP
SCK
SI
11
10
9
NC
NC
WP
V
SS
4
5
NC
SCK
6
7
V
8
SI
SS
FN8131.2
June 30, 2008
3
X5323, X5325
Pin Descriptions
PIN NUMBER
(SOIC/PDIP)
PIN NUMBER
TSSOP
PIN NAME
PIN FUNCTION
1
1
CS/WDI
Chip Select Input. CS HIGH, deselects the device and the SO output pin is at a high impedance
state. Unless a nonvolatile write cycle is underway, the device will be in the stand-by power mode.
CS LOW enables the device, placing it in the active power mode. Prior to the start of any operation
after power-up, a HIGH to LOW transition on CS is required.
Watchdog Input. A HIGH to LOW transition on the WDI pin restarts the watchdog timer. The
absence of a HIGH to LOW transition within the watchdog time out period results in
RESET/RESET going active.
2
5
2
8
SO
SI
Serial Output. SO is a push/pull serial data output pin. A read cycle shifts data out on this pin. The
falling edge of the serial clock (SCK) clocks the data out.
Serial Input. SI is a serial data input pin. Input all opcodes, byte addresses, and memory data on this
pin. The rising edge of the serial clock (SCK) latches the input data. Send all opcodes (Table 1),
addresses and data MSB first.
6
3
9
6
SCK
WP
Serial Clock. The serial clock controls the serial bus timing for data input and output. The rising edge
of SCK latches in the opcode, address, or data bits present on the SI pin. The falling edge of SCK
changes the data output on the SO pin.
Write Protect. The WP pin works in conjunction with a nonvolatile WPEN bit to “lock” the setting
of the watchdog timer control and the memory write protect bits.
4
8
7
7
VSS
VCC
Ground
14
13
Supply Voltage
RESET/
RESET
Reset Output. RESET/RESET is an active LOW/HIGH, open drain output which goes active
whenever VCC falls below the minimum VCC sense level. It will remain active until VCC rises above
the minimum VCC sense level for 200ms. RESET/RESET goes active if the watchdog timer is
enabled and CS remains either HIGH or LOW longer than the selectable watchdog time out
period. A falling edge of CS will reset the watchdog timer. RESET/RESET goes active on power-
up at about 1V and remains active for 200ms after the power supply stabilizes.
3 to 5,10 to 12
NC
No internal connections
FN8131.2
June 30, 2008
4
X5323, X5325
To set the new VTRIP voltage, apply the desired VTRIP
threshold to the VCC pin and tie the CS/WDI pin and the WP
pin HIGH. RESET/RESET and SO pins are left
Principles of Operation
Power-on Reset
Application of power to the X5323/X5325 activates a
power-on reset circuit. This circuit goes active at about 1V
and pulls the RESET/RESET pin active. This signal prevents
the system microprocessor from starting to operate with
insufficient voltage or prior to stabilization of the oscillator. As
long as RESET/RESET pin is active, the device will not
respond to any Read/Write instruction. When VCC exceeds
the device VTRIP value for 200ms (nominal) the circuit
releases RESET/RESET, allowing the processor to begin
executing code.
unconnected. Then apply the programming voltage VP to
both SCK and SI and pulse CS/WDI LOW then HIGH.
Remove VP and the sequence is complete.
CS
V
P
SCK
SI
V
P
Low Voltage Monitoring
During operation, the X5323/X5325 monitors the VCC level
and asserts RESET/RESET if supply voltage falls below a
preset minimum VTRIP. The RESET/RESET signal prevents
the microprocessor from operating in a power fail or
brown-out condition. The RESET/RESET signal remains
active until the voltage drops below 1V. It also remains active
until VCC returns and exceeds VTRIP for 200ms.
FIGURE 1. SET VTRIP VOLTAGE
Resetting the V
Voltage
TRIP
This procedure sets the VTRIP to a “native” voltage level. For
example, if the current VTRIP is 4.4V and the VTRIP is reset,
the new VTRIP is something less than 1.7V. This procedure
must be used to set the voltage to a lower value.
Watchdog Timer
To reset the VTRIP voltage, apply a voltage between 2.7V
and 5.5V to the VCC pin. Tie the CS/WDI pin, the WP pin,
and the SCK pin HIGH. RESET/RESET and SO pins are left
unconnected. Then apply the programming voltage VP to the
SI pin ONLY and pulse CS/WDI LOW then HIGH. Remove
VP and the sequence is complete.
The watchdog timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microprocessor must
toggle the CS/WDI pin periodically to prevent a
RESET/RESET signal. The CS/WDI pin must be toggled
from HIGH to LOW prior to the expiration of the watchdog
time out period. The state of two nonvolatile control bits in
the status register determine the watchdog timer period. The
microprocessor can change these watchdog bits, or they
may be “locked” by tying the WP pin LOW and setting the
WPEN bit HIGH.
CS
V
CC
SCK
SI
V
Threshold Reset Procedure
CC
V
P
The X5323/X5325 has a standard VCC threshold (VTRIP
)
voltage. This value will not change over normal operating
and storage conditions. However, in applications where the
standard VTRIP is not exactly right, or for higher precision in
the VTRIP value, the X5323/X5325 threshold may be
adjusted.
FIGURE 2. RESET VTRIP VOLTAGE
Setting the V
Voltage
TRIP
This procedure sets the VTRIP to a higher voltage value. For
example, if the current VTRIP is 4.4V and the new VTRIP is
4.6V, this procedure directly makes the change. If the new
setting is lower than the current setting, then it is necessary
to reset the trip point before setting the new value.
FN8131.2
June 30, 2008
5
X5323, X5325
V
PROGRAMMING
TRIP
EXECUTE
RESET V
TRIP
SEQUENCE
SET V = V APPLIED =
CC
CC
DESIRED V
TRIP
EXECUTE
SET V
SEQUENCE
NEW V APPLIED =
CC
NEW V APPLIED =
CC
TRIP
OLD V APPLIED - ERROR
CC
OLD V APPLIED + ERROR
CC
EXECUTE
APPLY 5V TO V
CC
RESET V
TRIP
SEQUENCE
DECREMENT V
CC
(V = V - 10mV)
CC
CC
NO
RESET PIN
GOES ACTIVE?
YES
ERROR ≤ EMAX
ERROR ≥ EMAX
MEASURED V
DESIRED V
-
TRIP
TRIP
ERROR < EMAX
EMAX = MAXIMUM DESIRED ERROR
DONE
FIGURE 3. VTRIP PROGRAMMING SEQUENCE FLOW CHART
V
P
NC
NC
4.7kΩ
RESET
4.7kΩ
V
TRIP
1
2
3
4
8
7
6
5
ADJ.
NC
X5323,
X5325
+
PROGRAM
RESET V
TRIP
10kΩ
10kΩ
TEST V
TRIP
SET V
TRIP
FIGURE 4. SAMPLE VTRIP RESET CIRCUIT
FN8131.2
June 30, 2008
6
X5323, X5325
Status Register
SPI Serial Memory
The RDSR instruction provides access to the status register.
The status register may be read at any time, even during a
write cycle. The status register is formatted as follows:
The memory portion of the device is a CMOS serial EEPROM
array with Intersil’s block lock protection. The array is
internally organized as x8. The device features a Serial
Peripheral Interface (SPI) and software protocol allowing
operation on a simple four-wire bus.
7
6
5
4
3
2
1
0
WPEN
FLB
WD1
WD0
BL1
BL0
WEL
WIP
The device utilizes Intersil’s proprietary Direct Write™ cell,
providing a minimum endurance of 100,000 cycles and a
minimum data retention of 100 years.
The Write-In-Progress (WIP) bit is a volatile, read only bit
and indicates whether the device is busy with an internal
nonvolatile write operation. The WIP bit is read using the
RDSR instruction. When set to a “1”, a nonvolatile write
operation is in progress. When set to a “0”, no write is in
progress.
The device is designed to interface directly with the
synchronous Serial Peripheral Interface (SPI) of many
popular microcontroller families. It contains an 8-bit
instruction register that is accessed via the SI input, with
data being clocked in on the rising edge of SCK. CS must be
LOW during the entire operation.
The Write Enable Latch (WEL) bit indicates the status of
the write enable latch. When WEL = 1, the latch is set
HIGH and when WEL = 0 the latch is reset LOW. The WEL
bit is a volatile, read only bit. It can be set by the WREN
instruction and can be reset by the WRDS instruction.
All instructions (Table 1), addresses and data are transferred
MSB first. Data input on the SI line is latched on the first
rising edge of SCK after CS goes LOW. Data is output on the
SO line by the falling edge of SCK. SCK is static, allowing
the user to stop the clock and then start it again to resume
operations where left off.
The block lock bits, BL0 and BL1, set the level of block lock
protection. These nonvolatile bits are programmed using the
WRSR instruction and allow the user to protect one quarter,
one half, all or none of the EEPROM array. Any portion of the
array that is block lock protected can be read but not written. It
will remain protected until the BL bits are altered to disable
block lock protection of that portion of memory.
Write Enable Latch
The device contains a write enable latch. This latch must be
SET before a write operation is initiated. The WREN
instruction will set the latch and the WRDI instruction will
reset the latch (Figure 3). This latch is automatically reset
upon a power-up condition and after the completion of a
valid write cycle.
TABLE 1. INSTRUCTION SET
INSTRUCTION NAME
WREN
INSTRUCTION FORMAT*
0000 0110
OPERATION
Set the write enable latch (enable write operations)
Set flag bit
SFLB
0000 0000
WRDI/RFLB
RSDR
0000 0100
Reset the write enable latch/reset flag bit
Read status register
0000 0101
WRSR
0000 0001
Write status register (watchdog, block lock, WPEN and flag bits)
Read data from memory array beginning at selected address
Write data to memory array beginning at selected address
READ
0000 0011
WRITE
0000 0010
NOTE: *Instructions are shown MSB in leftmost position. Instructions are transferred MSB first.
TABLE 2. BLOCK PROTECT MATRIX
WREN CMD
STATUS REGISTER
DEVICE PIN
BLOCK
Protected Block
Protected
BLOCK
Unprotected Block
Protected
STATUS REGISTER
WPEN, BL0, BL1 WD0, WD1
Protected
WEL
WPEN
WP
X
0
1
1
1
X
1
0
X
0
Protected
Writable
Protected
X
Protected
Writable
Writable
1
Protected
Writable
Writable
FN8131.2
June 30, 2008
7
X5323, X5325
.
In Circuit Programmable ROM Mode
STATUS
This mechanism protects the block lock and watchdog bits
from inadvertent corruption.
REGISTER BITS
ARRAY ADDRESSES PROTECTED
X5323/X5325
BL1
0
BL0
0
In the locked state (programmable ROM mode) the WP pin is
LOW and the nonvolatile bit WPEN is “1”. This mode disables
nonvolatile writes to the device’s status register.
None (factory default)
$0C00 to $0FFF
0
1
1
0
$0800 to $0FFF
Setting the WP pin LOW while WPEN is a “1” while an
internal write cycle to the status register is in progress will
not stop this write operation, but the operation disables
subsequent write attempts to the status register.
1
1
$0000 to $0FFF
The watchdog timer bits, WD0 and WD1, select the
watchdog time out period. These nonvolatile bits are
programmed with the WRSR instruction.
When WP is HIGH, all functions, including nonvolatile writes
to the status register operate normally. Setting the WPEN bit
in the status register to “0” blocks the WP pin function,
allowing writes to the status register when WP is HIGH or
LOW. Setting the WPEN bit to “1” while the WP pin is LOW
activates the programmable ROM mode, thus requiring a
change in the WP pin prior to subsequent status register
changes. This allows manufacturing to install the device in a
system with WP pin grounded and still be able to program
the status register. Manufacturing can then load
STATUS REGISTER BITS
WATCHDOG TIME-OUT
WD1
WD0
(TYPICAL)
0
0
1
1
0
1
0
1
1.4s
600ms
200ms
disabled (factory default)
configuration data, manufacturing time and other parameters
into the EEPROM, then set the portion of memory to be
protected by setting the block lock bits, and finally set the
“OTP mode” by setting the WPEN bit. Data changes now
require a hardware change.
The FLAG bit shows the status of a volatile latch that can be
set and reset by the system using the SFLB and RFLB
instructions. The flag bit is automatically reset upon
power-up. This flag can be used by the system to determine
whether a reset occurs as a result of a watchdog time out or
power failure.
Read Sequence
When reading from the EEPROM memory array, CS is first
pulled low to select the device. The 8-bit READ instruction is
transmitted to the device, followed by the 16-bit address.
After the READ opcode and address are sent, the data
stored in the memory at the selected address is shifted out
on the SO line. The data stored in memory at the next
address can be read sequentially by continuing to provide
clock pulses. The address is automatically incremented to
the next higher address after each byte of data is shifted out.
Note: The Watch Dog Timer is shipped disabled. (WD1 = 1,
WD0 = 1. The factory default for Memory Block Protection is
‘None’. (BL1 = 0, BL0 = 0).
The nonvolatile WPEN bit is programmed using the WRSR
instruction. This bit works in conjunction with the WP pin to
provide an in-circuit programmable ROM function (Table 2). WP
is LOW and WPEN bit programmed HIGH disables all status
register write operations.
CS
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30
SCK
SI
16-BIT ADDRESS
15 14 13
INSTRUCTION
3
2
1
0
DATA OUT
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
MSB
FIGURE 5. READ EEPROM ARRAY SEQUENCE
FN8131.2
June 30, 2008
8
X5323, X5325
When the highest address is reached, the address counter
For the page write operation (byte or page write) to be
completed, CS can only be brought HIGH after bit 0 of the
last data byte to be written is clocked in. If it is brought HIGH
at any other time, the write operation will not be completed
(Figure 4).
rolls over to address $0000 allowing the read cycle to be
continued indefinitely. The read operation is terminated by
taking CS high. Refer to the read EEPROM Array Sequence
(Figure 1).
To read the status register, the CS line is first pulled low to
select the device followed by the 8-bit RDSR instruction.
After the RDSR opcode is sent, the contents of the status
register are shifted out on the SO line. Refer to the read
status register sequence (Figure 2).
To write to the status register, the WRSR instruction is
followed by the data to be written (Figure 5). Data bits 0 and
1 must be “0”.
While the write is in progress following a status register or
EEPROM Sequence, the status register may be read to
check the WIP bit. During this time the WIP bit will be high.
Write Sequence
Prior to any attempt to write data into the device, the “Write
Enable” Latch (WEL) must first be set by issuing the WREN
instruction (Figure 3). CS is first taken LOW, then the WREN
instruction is clocked into the device. After all eight bits of the
instruction are transmitted, CS must then be taken HIGH. If
the user continues the write operation without taking CS
HIGH after issuing the WREN instruction, the write operation
will be ignored.
Operational Notes
The device powers-up in the following state:
• The device is in the low power standby state.
• A HIGH to LOW transition on CS is required to enter an
active state and receive an instruction.
• SO pin is high impedance.
• The write enable latch is reset.
• The flag bit is reset.
To write data to the EEPROM memory array, the user then
issues the WRITE instruction followed by the 16-bit address
and then the data to be written. Any unused address bits are
specified to be “0’s”. The WRITE operation minimally takes
32 clocks. CS must go low and remain low for the duration of
the operation. If the address counter reaches the end of a
page and the clock continues, the counter will roll back to the
first address of the page and overwrite any data that may
have been previously written.
• Reset signal is active for tPURST
.
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
• A WREN instruction must be issued to set the write enable
latch.
Note: When writing more than one page, you must wait one
write cycle (10ms typical) when going from one page to
another. This is required for the internal nonvolatile memory
to be programmed correctly.
• CS must come HIGH at the proper clock count in order to
start a nonvolatile write cycle.
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14
SCK
INSTRUCTION
SI
DATA OUT
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
MSB
FIGURE 6. READ STATUS REGISTER SEQUENCE
FN8131.2
June 30, 2008
9
X5323, X5325
Symbol Table
CS
WAVEFORM
INPUTS
OUTPUTS
0
1
2
3
4
5
6
7
Must be
steady
Will be
steady
SCK
SI
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
HIGH IMPEDANCE
SO
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
FIGURE 7. WRITE ENABLE LATCH SEQUENCE
N/A
Center Line
is High
Impedance
CS
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
SCK
INSTRUCTION
16-BIT ADDRESS
15 14 13
DATA BYTE 1
3
2
1
0
7
6
5
4
3
2
1
0
SI
CS
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
SCK
SI
DATA BYTE 2
DATA BYTE 3
DATA BYTE N
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
6
5
4
3
2
1
0
FIGURE 8. WRITE SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
SCK
INSTRUCTION
DATA BYTE
7
6
5
4
3
2
1
0
SI
HIGH IMPEDANCE
SO
FIGURE 9. STATUS REGISTER WRITE SEQUENCE
FN8131.2
June 30, 2008
10
X5323, X5325
Absolute Maximum Ratings
Thermal Information
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any Pin with Respect to VSS . . . . . . . . . . . .-1.0V to +7V
DC Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . .-40°C to +85°C
Temperature Range (Commercial). . . . . . . . . . . . . . . . 0°C to +70°C
Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
DC Electrical Specifications Over the recommended operating conditions, unless otherwise specified
PARAMETER
SYMBOL
ICC1
ICC2
ISB1
ISB2
ISB3
ILI
TEST CONDITIONS
SCK = VCC x 0.1/VCC x 0.9 @ 2MHz, SO = Open
SCK = VCC x 0.1/VCC x 0.9 @ 2MHz, SO = Open
CS = VCC, VIN = VSS or VCC, VCC = 5.5V
CS = VCC, VIN = VSS or VCC, VCC = 5.5V
CS = VCC, VIN = VSS or VCC, VCC =3.6V
VIN = VSS to VCC
MIN
TYP
MAX
UNIT
mA
mA
µA
µA
µA
µA
µA
V
V
CC Write Current (active)
5
VCC Read Current (active)
0.4
V
V
CC Standby Current WDT = OFF
CC Standby Current WDT = ON
1
50
VCC Standby Current WDT = ON
Input Leakage Current
Output Leakage Current
Input LOW Voltage
20
0.1
0.1
10
ILO
VOUT = VSS to VCC
10
VIL
-0.5
VCC x 0.3
(Note 1)
Input HIGH Voltage
VIH
VCC x 0.7
VCC + 0.5
V
(Note 1)
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
Reset Output LOW Voltage
VOL1
VOL2
VOL3
VOH1
VOH2
VOH3
VOLS
VCC > 3.3V, IOL = 2.1mA
2V < VCC ≤ 3.3V, IOL = 1mA
VCC ≤ 2V, IOL = 0.5mA
VCC > 3.3V, IOH = -1.0mA
2V < VCC ≤ 3.3V, IOH = -0.4mA
VCC ≤ 2V, IOH = -0.25mA
IOL = 1mA
0.4
0.4
0.4
V
V
V
V
V
V
V
VCC - 0.8
VCC - 0.4
VCC - 0.2
0.4
Capacitance
TA = +25°C, f = 1MHz, VCC = 5V
SYMBOL
TEST
CONDITIONS
VOUT = 0V
VIN = 0V
MAX
UNIT
pF
C
OUT (Note 2) Output Capacitance (SO, RESET/RESET)
IN (Note 2) Input Capacitance (SCK, SI, CS, WP)
NOTES:
8
6
C
pF
1. VIL min and VIH max are for reference only and are not tested.
2. This parameter is periodically sampled and not 100% tested.
FN8131.2
June 30, 2008
11
X5323, X5325
Equivalent AC Load Circuit at 5V V
AC Test Conditions
CC
Input pulse levels
VCC x 0.1 to VCC x 0.9
10ns
5V
5V
Input rise and fall times
Input and output timing level
4.6kΩ
VCC x 0.5
2.06kΩ
OUTPUT
3.03kΩ
RESET/RESET
30pF
100pF
AC Electrical Specifications
Input pulse levels = VCC x 0.1 to VCC x 0.9; input rise and fall times = 10ns; input and ouput timing
level = VCC x 0.5. Over recommended operating conditions, unless otherwise specified.
2.7 TO 5.5V
PARAMETER
SYMBOL
MIN
MAX
UNIT
SERIAL INPUT TIMING
Clock Frequency
Cycle Time
fSCK
tCYC
tLEAD
tLAG
0
2
MHz
ns
500
250
250
200
250
50
CS Lead Time
ns
CS Lag Time
ns
Clock HIGH Time
Clock LOW Time
Data Set-up Time
Data Hold Time
Input Rise Time
Input Fall Time
tWH
ns
tWL
ns
tSU
ns
tH
50
ns
t
RI (Note 3)
100
100
ns
tFI (Note 3)
tCS
ns
CS Deselect Time
Write Cycle Time
500
ns
t
WC (Note 4)
10
ms
Serial Input Timing
t
CS
CS
t
t
LAG
LEAD
SCK
t
t
t
t
FI
SU
H
RI
SI
MSB IN
LSB IN
HIGH IMPEDANCE
SO
FN8131.2
June 30, 2008
12
X5323, X5325
Serial Output Timing
2.7 TO 5.5V
MAX
PARAMETER
SYMBOL
fSCK
tDIS
MIN
UNIT
MHz
ns
Clock Frequency
Output Disable Time
Output Valid From Clock Low
Output Hold Time
Output Rise Time
Output Fall Time
NOTES:
0
2
250
250
tV
ns
tHO
0
ns
tRO (Note 3)
100
100
ns
t
FO (Note 3)
ns
3. This parameter is periodically sampled and not 100% tested.
4. tWC is the time from the rising edge of CS after a valid write sequence has been sent to the end of the self-timed internal nonvolatile write cycle.
Serial Output Timing
CS
t
t
t
LAG
CYC
WH
SCK
SO
SI
t
t
t
t
DIS
V
HO
WL
MSB OUT
MSB–1 OUT
LSB OUT
ADDR
LSB IN
Power-Up and Power-Down Timing
V
V
TRIP
TRIP
V
CC
t
PURST
0V
t
t
F
PURST
t
RPD
t
R
RESET (X5323)
RESET (X5323)
FN8131.2
June 30, 2008
13
X5323, X5325
RESET Output Timing
SYMBOL
PARAMETER
MIN
4.5
TYP
4.63
4.38
2.92
2.63
20
MAX
4.75
4.5
UNIT
V
VTRIP
Reset Trip Point Voltage, X5323-4.5A, X5323-4.5A
Reset Trip Point Voltage, X5323, X5325
4.25
2.85
2.55
V
Reset Trip Point Voltage, X5323-2.7A, X5325-2.7A
Reset Trip Point Voltage, X5323-2.7, X5325-2.7
VTRIP Hysteresis (HIGH to LOW vs LOW to HIGH VTRIP Voltage)
Power-up Reset Time-Out
3.0
V
2.7
V
VTH
mV
ms
ns
µs
µs
V
tPURST
100
200
280
500
t
RPD (Note 5) VCC Detect To Reset/Output
tF (Note 5) VCC Fall Time
100
100
1
tR (Note 5) VCC Rise Time
VRVALID
NOTE:
Reset Valid VCC
5. This parameter is periodically sampled and not 100% tested.
CS/WDI vs RESET/RESET Timing
CS/WDI
t
CST
RESET
t
t
t
t
RST
WDO
RST
WDO
RESET
RESET/RESET Output Timing
SYMBOL
PARAMETER
MIN
TYP
MAX
UNIT
tWDO
Watchdog Time-Out Period
WD1 = 1, WD0 = 0
100
450
1
200
600
1.4
300
800
2
ms
ms
s
WD1 = 0, WD0 = 1
WD1 = 0, WD0 = 0
tCST
tRST
CS Pulse Width to Reset the Watchdog
Reset Time-Out
400
100
ns
ms
200
300
FN8131.2
June 30, 2008
14
X5323, X5325
V
Set Conditions
TRIP
t
THD
V
V
CC
TRIP
t
TSU
t
RP
t
t
VPH
t
P
VPS
CS
t
t
t
VPO
VPH
VPS
V
P
SCK
SI
V
t
P
VPO
V
Reset Conditions
TRIP
V
*
CC
t
RP
t
t
VP1
t
P
VPS
CS
t
t
t
VPS
VPO
VPH
V
CC
V
SCK
SI
t
P
VPO
*V > PROGRAMMED V
CC
TRIP
V
Programming Specifications VCC = 1.7 to 5.5V; Temperature = 0°C to +70°C.
TRIP
PARAMETER
DESCRIPTION
MIN
1
MAX
UNIT
µs
tVPS
tVPH
tP
SCK VTRIP Program Voltage Set-up Time
SCK VTRIP Program Voltage Hold Time
VTRIP Program Pulse Width
1
µs
1
µs
tTSU
tTHD
VTRIP Level Set-up Time
10
10
µs
VTRIP Level Hold (Stable) Time
ms
FN8131.2
June 30, 2008
15
X5323, X5325
V
Programming Specifications VCC = 1.7 to 5.5V; Temperature = 0°C to +70°C. (Continued)
TRIP
PARAMETER
DESCRIPTION
MIN
MAX
UNIT
ms
ms
ms
V
tWC
tRP
tVPO
VP
VTRAN
Vta1
VTRIP Write Cycle Time
10
VTRIP Program Cycle Recovery Period (Between Successive Programming Cycles)
SCK VTRIP Program Voltage Off-Time Before Next Cycle
10
0
Programming Voltage
15
18
5.0
VTRIP Programed Voltage Range
1.7
-0.1
-25
-25
-25
V
Initial VTRIP Program Voltage Accuracy (VCC Applied-VTRIP) (Programmed at +25°C)
Subsequent VTRIP Program Voltage Accuracy [(VCC Applied-Vta1)-VTRIP] (Programmed at +25°C)
VTRIP Program Voltage Repeatability (Successive Program Operations; Programmed at +25°C)
VTRIP Program Variation After Programming (0°C to +75°C; Programmed at +25°C)
+0.4
+25
+25
+25
V
Vta2
mV
mV
mV
Vtr
Vtv
NOTE:
6. VTRIP programming parameters are periodically sampled and are not 100% tested.
Typical Performance Curves
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
18
WATCHDOG TIMER ON (V = 5V)
CC
16
14
12
10
8
-40°C
WATCHDOG TIMER ON (V = 5V)
+25°C
CC
+90°C
6
4
2
WATCHDOG TIMER OFF (V = 3V, 5V)
CC
0
-40
25
90
1.7
2.4
3.1
3.8
4.5
5.2
TEMPERATURE (°C)
VOLTAGE (V)
FIGURE 10. V SUPPLY CURRENT vs TEMPERATURE (I
)
FIGURE 11. T vs VOLTAGE/TEMPERATURE (WD1, 0 = 1, 1)
WDO
CC
SB
0.80
0.75
0.70
0.65
0.60
0.55
0.50
5.025
5.000
V
= 5V
TRIP
-40°C
4.975
3.525
3.500
3.475
2.525
2.500
2.475
+25°C
+90°C
V
= 3.5V
= 2.5V
TRIP
V
TRIP
0.45
1.7
0
25
85
2.4
3.1
VOLTAGE (V)
vs VOLTAGE/TEMPERATURE (WD1, 0 = 1, 0)
WDO
3.8
4.5
5.2
TEMPERATURE (°C)
FIGURE 12. V
vs TEMPERATURE (PROGRAMMED AT +25°C)
FIGURE 13. T
TRIP
FN8131.2
June 30, 2008
16
X5323, X5325
Typical Performance Curves
205
200
195
190
185
180
175
170
165
160
205
200
195
190
185
180
175
170
165
160
-40°C
+25°C
+90°C
-40
25
90
1.7
2.4
3.1
3.8
4.5
5.2
VOLTAGE (V)
TEMPERATURE (°C)
FIGURE 14. T
vs TEMPERATURE
FIGURE 15. T
vs VOLTAGE/TEMPERATURE (WD1, 0 0 = 0, 1)
WDO
PURST
FN8131.2
June 30, 2008
17
X5323, X5325
Plastic Dual-In-Line Packages (PDIP)
E
N
1
D
PIN #1
INDEX
A2
A
E1
SEATING
PLANE
L
c
A1
NOTE 5
2
N/2
eA
eB
e
b
b2
MDP0031
PLASTIC DUAL-IN-LINE PACKAGE
INCHES
SYMBOL
PDIP8
0.210
0.015
0.130
0.018
0.060
0.010
0.375
0.310
0.250
0.100
0.300
0.345
0.125
8
PDIP14
0.210
0.015
0.130
0.018
0.060
0.010
0.750
0.310
0.250
0.100
0.300
0.345
0.125
14
PDIP16
0.210
0.015
0.130
0.018
0.060
0.010
0.750
0.310
0.250
0.100
0.300
0.345
0.125
16
PDIP18
0.210
0.015
0.130
0.018
0.060
0.010
0.890
0.310
0.250
0.100
0.300
0.345
0.125
18
PDIP20
0.210
0.015
0.130
0.018
0.060
0.010
1.020
0.310
0.250
0.100
0.300
0.345
0.125
20
TOLERANCE
MAX
NOTES
A
A1
A2
b
MIN
±0.005
±0.002
b2
c
+0.010/-0.015
+0.004/-0.002
±0.010
D
1
2
E
+0.015/-0.010
±0.005
E1
e
Basic
eA
eB
L
Basic
±0.025
±0.010
N
Reference
Rev. C 2/07
NOTES:
1. Plastic or metal protrusions of 0.010” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions E and eA are measured with the leads constrained perpendicular to the seating plane.
4. Dimension eB is measured with the lead tips unconstrained.
5. 8 and 16 lead packages have half end-leads as shown.
FN8131.2
June 30, 2008
18
X5323, X5325
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M
C A B
e
H
C
A2
A1
GAUGE
PLANE
SEATING
PLANE
0.010
L
4° ±4°
0.004 C
b
0.010 M
C
A
B
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
SYMBOL
SO-8
0.068
0.006
0.057
0.017
0.009
0.193
0.236
0.154
0.050
0.025
0.041
0.013
8
SO-14
0.068
0.006
0.057
0.017
0.009
0.341
0.236
0.154
0.050
0.025
0.041
0.013
14
TOLERANCE
MAX
NOTES
A
A1
A2
b
0.068
0.006
0.057
0.017
0.009
0.390
0.236
0.154
0.050
0.025
0.041
0.013
16
0.104
0.007
0.092
0.017
0.011
0.406
0.406
0.295
0.050
0.030
0.056
0.020
16
0.104
0.007
0.092
0.017
0.011
0.504
0.406
0.295
0.050
0.030
0.056
0.020
20
0.104
0.007
0.092
0.017
0.011
0.606
0.406
0.295
0.050
0.030
0.056
0.020
24
0.104
0.007
0.092
0.017
0.011
0.704
0.406
0.295
0.050
0.030
0.056
0.020
28
-
±0.003
±0.002
±0.003
±0.001
±0.004
±0.008
±0.004
Basic
-
-
-
c
-
D
1, 3
E
-
E1
e
2, 3
-
L
±0.009
Basic
-
L1
h
-
Reference
Reference
-
N
-
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
FN8131.2
June 30, 2008
19
X5323, X5325
Thin Shrink Small Outline Plastic Packages (TSSOP)
M14.173
N
14 LEAD THIN SHRINK SMALL OUTLINE PLASTIC
PACKAGE
INDEX
AREA
0.25(0.010)
M
B M
E
E1
-B-
INCHES
MIN
MILLIMETERS
GAUGE
PLANE
SYMBOL
MAX
0.047
0.006
0.041
0.0118
0.0079
0.199
0.177
MIN
-
MAX
1.20
0.15
1.05
0.30
0.20
5.05
4.50
NOTES
A
A1
A2
b
-
-
1
2
3
0.002
0.031
0.0075
0.0035
0.195
0.169
0.05
0.80
0.19
0.09
4.95
4.30
-
L
0.25
0.010
-
0.05(0.002)
SEATING PLANE
A
9
-A-
D
c
-
D
3
-C-
α
E1
e
4
A2
e
A1
0.026 BSC
0.65 BSC
-
c
b
0.10(0.004)
E
0.246
0.256
6.25
0.45
6.50
0.75
-
0.10(0.004) M
C
A M B S
L
0.0177
0.0295
6
N
14
14
7
NOTES:
0o
8o
0o
8o
-
α
1. These package dimensions are within allowable dimensions of
JEDEC MO-153-AC, Issue E.
Rev. 2 4/06
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm
(0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions. Inter-
lead flash and protrusions shall not exceed 0.15mm (0.006 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable dambar
protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimen-
sion at maximum material condition. Minimum space between protru-
sion and adjacent lead is 0.07mm (0.0027 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact. (Angles in degrees)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8131.2
June 30, 2008
20
相关型号:
X5323S8Z-2.7A-T1
1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8, ROHS COMPLIANT, PLASTIC, SOIC-8
RENESAS
©2020 ICPDF网 联系我们和版权申明