QPA7489A [RFMD]
CASCADABLE SiGe HBT MMIC AMPLIFIER;型号: | QPA7489A |
厂家: | RF MICRO DEVICES |
描述: | CASCADABLE SiGe HBT MMIC AMPLIFIER 放大器 |
文件: | 总9页 (文件大小:639K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
RFMD + TriQuint = Qorvo
QPA7489A
DC to 3000 MHz, CASCADABLE SiGe HBT
MMIC AMPLIFIER
The QPA7489A is a high performance SiGe HBT MMIC
amplifier. A Darlington configuration provides high FT and
excellent thermal performance. The heterojunction increases
breakdown voltage and minimizes leakage current between
junctions. Cancellation of emitter junction non-linearities results
in higher suppression of intermodulation products. Only two DC-
blocking capacitors, a bias resistor, and an optional RF choke
are required for operation.
SOT-89 Package
Features
. DC to 3000MHz Operation
. High Output IP3: +37.7 dBm Typical
at ꢀ850 MHz
. Low Noise Figure: 3.2dB Typical at
1950 MHz
Functional Block Diagram
Applications
. Oscillator Amplifiers
. Power Amplifier for Low or Medium
Power Applications
. IF/RF Buffer Amplifier
. LO Driver Amplifier
Ordering Information
QPA7489ASQ
Sample Bag with 25 pieces
QPA7489ASR
7" Reel with 100 pieces
QPA7489ATR13
QPA7489APCK401
13" Reel with 3000 pieces
850MHz, 8V Operation PCBA with 5-piece Sample Bag
Revision DS20160202
Disclaimer: Subject to change without notice
- 1 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Absolute Maximum Ratings
Caution! ESD sensitive device.
Parameter
Rating
+7.0
Units
V
Device Voltage(VD)
Device Current (ID)
170
mA
dBm
dBm
°C
Note 1
RF Input Power
+16
RFMD Green: RoHS status based on EU Directive
2011/65/EU (at time of this document revision), halogen
free per IEC 61249-2-21, < 1000ꢁppm each of antimony
trioxide in polymeric materials and red phosphorus as a
flame retardant, and <2% antimony in solder.
RF Input Power Note 2
Storage Temperature
ESD Rating (HBM)
+2
-55 to +150
2000 (Class 2)
MSL2
V
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability. Specified typical performance or functional -
operation of the device under Absolute Maximum Rating conditions is
not implied.
Moisture Sensitivity Level
-
Notes:
1. Load Condition 1: ZL = 50ꢀΩ
2. Load Condition 2: ZL = 10:1 VSWR, Take into account out of band load VSWR
presented by devices such as SAW filters to determine maximum RF input
power. Reflected harmonic levels in saturation are significant.
3. Operation of this device beyond any one of these limits may cause permanent
damage. For reliable continuous operation, the device voltage and current
must not exceed the maximum operating values specified in the table on this
page.
4. Bias Conditions should also satisfy the following expression: IDVD <(TJ -TL)/
RTH, and TL =TLEAD
.
Recommended Operating Conditions
Rating
Min Typ Max
Parameter
Units
Operating Temperature Range
Junction Temperature (TJ)
Device Operating Voltage
-40
+85
ꢀ°C
ꢀ°C
V
+125
+4.7 +5.0 +5.3
Electrical Specifications – General
Specification
Typ
Parameter
Units Conditions
Min
Max
21.2
17.7
dB
dB
850MHz
1950MHz
2400MHz
850MHz
1950MHz
2400MHz
500MHz
850MHz
1950MHz
2400MHz
850MHz
1950MHz
2400MHz
Small Signal Gain, S21
16.9
dB
+22.1
+21.1
+20.1
+39.1
+37.7
+34.1
+32.5
10.5
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dB
Output Power at 1ꢀdB Compression
Output Third Order Intercept Point
Input Return Loss, S11
12.3
dB
14.9
dB
Test Conditions unless otherwise specified: +VD = +5 V, VS = 8 V, ID = 118 mA Typ., OIP3 Tone Spacing=1ꢀMHz, POUT per tone = 0ꢀdBm,
RBIAS = 26Ω, TL = 25°C, ZS = ZL =50ꢀΩ
Revision DS20160202
Disclaimer: Subject to change without notice
- 2 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Electrical Specifications – General (Continued)
Specification
Parameter
Units Conditions
Min
Typ
Max
11.8
6.2
dB
dB
850MHz
Output Return Loss, S22
Reverse Isolation, S12
Noise Figure
1950MHz
2400MHz
850MHz
6.3
dB
23.8
23.5
23.3
2.8
dB
dB
1950MHz
2400MHz
850MHz
dB
dB
3.2
dB
1950MHz
2400MHz
3.4
dB
Thermal Resistance
45
°C/W
mA
Device Operating Current
118
Test Conditions unless otherwise specified: +VD = +5 V, VS = 8 V, ID = 118 mA Typ., OIP3 Tone Spacing=1ꢀMHz, POUT per tone = 0ꢀdBm,
RBIAS = 26Ω, TL = 25°C, ZS = ZL =50ꢀΩ
Revision DS20160202
Disclaimer: Subject to change without notice
- 3 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Typical Performance Using 850MHz Application Circuit
Revision DS20160202
Disclaimer: Subject to change without notice
- 4 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Typical Performance Using 850MHz Application Circuit
Revision DS20160202
Disclaimer: Subject to change without notice
- 5 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Evaluation Board and Schematic
Evaluation Board Bill of Materials For 850MHz Application Circuit
Reference
Designator
Description
Manufacturer
Manufacturer's P/N
Gain Block
U1
-
QORVO
QPA7489A
PCB
Viasystems
QPAXX89A
CAP, 1uF, 10%, 25V, X7R, 1206
CAP, 1000pF, 10%, 50V, X7R, 0402
CAP, 68pF, 5%, 50V, C0G, 0402
CAP, 100pF, 5%, 50V, C0G, 0402
RES, 26.1 OHM, 1%, 1/2W, 1210
IND, 33nH, 5%, M/L, 0603
C1
Murata Electronics
Murata Electronics
Murata Electronics
Murata Electronics
GRM31MR71E105KA01L
GRM155R71H102KA01D
GRM1555C1H680JA01D
GRM1555C1H101JA01D
C2
C3
C4, C5
R1
Panasonic Industrial Devices ERJ-14NF26R1U
L1
Murata Electronics
Amphenol RF Asia Corp
Samtec Inc.
LL1608-FSL33NJ
901-10426
CONN, SMA, EL, FLT, 0.068" SPE-000318
CONN, HDR, ST, 1x2, 0.100", HI-TEMP, T/H
J1. J2
P1
HTSW-102-07-G-S
Revision DS20160202
Disclaimer: Subject to change without notice
- 6 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Component Values For Specific Frequency and Voltage in Application Circuit
Frequency (MHz)
Reference
Designator
100
1000pF
100pF
470nH
500
220pF
100pF
68nH
850
100pF
68pF
33nH
1950
68pF
22pF
22nH
2400
56pF
22pF
18nH
C4, C5
C3
L1
Required Bias Resistance for ID =118mA
Bias Resistance = RBIAS + RLDC = ( VS -VD ) / ID
Supply Voltage (VS)
7 V
8 V
9 V
12 V
Bias Resistance (R1 = RBias
)
17 Ω
26 Ω
35 Ω
61 Ω
*Note: Bias resistor improves current stability over temperature
Pin Configuration and Description
Pin
Label
Description
RF input pin. This pin requires the use of an external DC blocking capacitor as shown in
the application schematics
1
2
3
RF IN
G
ND
Connect to ground per application circuit drawing.
RF output and bias pin. Bias will be supplied to this pin through an external RF choke. A DC
blocking capacitor is necessary on the RF output as shown in the application circuit
RF OUT
Exposed area on the bottom side of the package needs to be soldered to the ground plane
of the board for thermal and RF performance. Vias should be located under the EPAD as
shown in the recommended land pattern.
4
GND
Revision DS20160202
Disclaimer: Subject to change without notice
- 7 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Package Marking
Suggested Pad Layout (Dimensions in millimeters)
Revision DS20160202
Disclaimer: Subject to change without notice
- 8 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPA7489A
RFMD + TriQuint = Qorvo
Package Outline (Dimensions in millimeters)
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.rfmd.com
Tel: 1-844-890-8163
Email: customer.support@qorvo.com
For information about the merger of RFMD and TriQuint as Qorvo:
Web: www.qorvo.com
Important Notice
The information contained herein is believed to be reliable. RFMD makes no warranties regarding the information contained
herein. RFMD assumes no responsibility or liability whatsoever for any of the information contained herein. RFMD assumes
no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is
provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user.
All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant
information before placing orders for RFMD products. The information contained herein or any use of such information
does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether
with regard to such information itself or anything described by such information.
RFMD products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining
applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
Revision DS20160202
Disclaimer: Subject to change without notice
- 9 of 9 -
© 2016 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
相关型号:
©2020 ICPDF网 联系我们和版权申明