R1510S006D-T1-FE [RICOH]
Input Voltage Range (Maximum Rating) Max. 36.0V (50V);型号: | R1510S006D-T1-FE |
厂家: | RICOH ELECTRONICS DEVICES DIVISION |
描述: | Input Voltage Range (Maximum Rating) Max. 36.0V (50V) |
文件: | 总41页 (文件大小:1049K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
R1510S Series
Automatic Mode Shift 36 V 300 mA LDO
OUTLINE
NO.EA-185-140724
The R1510S is a voltage regulator (LDO) IC with a voltage detector (VD) featuring 300mA output current that
is developed with CMOS process technology. Each IC is equipped with a voltage detector and a regulator that
can provide the maximum 36V of operating voltage. This device has ECO function, which achieves low-power
consumption and high-speed transient response by switching the IC to low-power consumption mode at light load
condition and switching to high-speed mode at heavy load condition.
The switching point is internally fixed inside the IC. The IC switches from low-power consumption mode to high-
speed mode when IOUT=12mA (Typ.), and switch from high-speed mode to low-power consumption mode when
IOUT=3mA (Typ.).
Each IC is composed of a reference voltage unit, an error amplifier, a resistor network for setting output voltage,
an output current limit circuit for preventing overcurrent destruction, and a thermal shutdown circuit. The output
voltage and the detector threshold are internally fixed inside the IC.
The output voltage accuracy is ±1.6% and the detector threshold accuracy is ±1.7%. The output voltage type
is Nch open drain. The versions for the IC are selectable from A version (CE, VIN Detector), B version (SENSE
Detector), C version (Release Delay Circuit, VIN Detector), and D version (Release Delay Circuit, VOUT Detector).
FEATURES
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Input Voltage Range (Maximum Rating) ·······Max. 36.0V (50V)
Operating Temperature Range ···················-40°C to 105°C
Supply Current ·······································Typ. 110µA (High Speed Mode, VIN=14V)
Supply Current ·······································Typ. 12.5µA (Low-power Consumption Mode, VIN=14V)
Supply Current (Standby Mode) ·················Typ. 10µA (CE=0V, A Version)
Output Voltage Range······························2.5V to 12.0V (0.1V step)
Dropout Voltage······································Typ. 1.0V (IOUT=300mA, VOUT=5V)
Output Voltage Accuracy···························±1.6% (Ta=25°C)
Temperature Characteristics······················Typ. ±150ppm/°C (Output Voltage)
Detector Threshold··································2.3V to 12.0V (0.1V steps)
Detector Threshold Accuracy·····················±1.7% (Ta=25°C)
Temperature Characteristics······················Typ. ±100ppm/°C (Detector Threshold)
Output Type···········································Nch Open Drain
Line Regulation ······································Typ. 0.01%/V
Package················································HSOP-8E
Built-in Short Current Limit Circuit···············Typ. 50mA
Built-in Overcurrent Protection Circuit
Built-in Thermal Shutdown Circuit ···············Shutdown Temperature: Typ. 140°C,
·······································································Release Temperature: Typ. 125°C
Ceramic Capacitor Corresponding ··············6.8µF or more
●
1
R1510S
NO.EA-185-140724
APPLICATIONS
●
●
Power source for notebook PCs, digital TVs, telephones, private LAN systems, etc.
Power source for office equipments such as copiers, printers, facsimiles, scanners, and projectors
BLOCK DIAGRAMS
R1510SxxxA
(CE Pin, VIN Detector)
R1510SxxxB
(SENSE Detector)
5
VDD
1
VOUT
5
VDD
1
VOUT
Vref
Vref
Thermal
Shutdown
Current Limit
Thermal
Shutdown
Current Limit
2
4
GND
3
SENSE
2
4
GND
3
CE
Internal
Supply Voltage
Internal
Supply Voltage
DOUT
DOUT
Vref
Vref
R1510SxxxC
(CD Pin, VIN Detector)
R1510SxxxD
(CD Pin, VOUT Detector)
5
5
VDD
1
VDD
1
VOUT
VOUT
Vref
Vref
Thermal
Shutdown
Thermal
Shutdown
Current Limit
Current Limit
2
4
2
4
GND
GND
3
3
CD
CD
Internal
Supply Voltage
Internal
Supply Voltage
DOUT
VDET
Vref
Vref
2
R1510S
NO.EA-185-140724
SELECTION GUIDE
The users can select VR output voltage, VD detector threshold, and version that best fit their requirements.
Product Name
Package
Quantity per Reel
Pb Free
Halogen Free
HSOP-8E
1,000 pcs
Yes
Yes
R1510Sxxx∗-E2-FE
xxx: Select the ideal combination of the output voltage (VOUT) and the detector threshold (-VDET
from the code number starting from 001.
)
Refer to MARK SPECIFICATION TABLE for detailed information.
∗: Select the ideal version from A to D.
(A) Built-in Chip Enable, VIN Detector
(B) SENSE Detector Threshold
(C) Built-in Release Delay Circuit, VIN Detector
(D) Built-in Release Delay Circuit, VOUT Detector
PIN DESCRIPTIONS
• HSOP-8E
Top View
Bottom View
8
7
6
5
5
6
7
8
∗
1
2
3
4
4
3
2
1
Pin No.
Symbol
VOUT
Description
1
2
3
4
VR Output Pin
No Connection
Test Pin
NC
TP*3
DOUT
CE
SENSE*1
CD*2
VD Output Pin (Nch Open Drain)
A Version: Chip Enable Pin (“H” Active)
B Version: VD Sense Pin
5
C, D Versions: Release Output Delay (Power-on Reset) Time Setting Pin
6
7
8
TP*3
Test Pin
GND
VDD
Ground Pin
Input Pin
∗) The tab on the reverse side of the IC is in GND level and it should be connected to GND pin (recommended)
or should be left open.
∗1) B version monitors SENSE pin voltage.
∗2) The release output delay time of voltage detector can be set by connecting a capacitor to CD pin.
∗3) TP pin should be connected to GND.
3
R1510S
NO.EA-185-140724
ABSOLUTE MAXIMUM RATINGS
Symbol
VIN
Item
Rating
−0.3 to 50
−0.3 to 7.0
−0.3 to 50
−0.3 to 7.0
−0.3 to VIN+0.3 ≤ 50
−0.3 to 7.0
450
Unit
V
Input Voltage
VCE
Input Voltage (CE Pin, A Version)
Input Voltage (SENSE Pin, B Version)
Input Voltage (CD Pin, C or D Version)
Output Voltage (VR)
V
VSENSE
VCD
V
V
VOUT
V
VRESET
Output Voltage (VD)
V
IOUT
IOUT
1
2
Output Current (VR)
mA
mA
Output Current (VD)
20
Power Dissipation (HSOP-8E)∗
Ultra High Wattage Land Pattern
PD
2900
mW
Ta
Operating Temperature Range
Storage Temperature Range
-40 to 105
°C
°C
Tstg
−55 to 125
∗) Refer to PACKAGE INFORMATION for detailed information.
ABSOLUTE MAXIMUM RATINGS
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent
damages and may degrade the lifetime and safety for both device and system using the device in the field. The functional
operation at or over these absolute maximum ratings is not assured.
4
R1510S
NO.EA-185-140724
ELECTRICAL CHARACTERISTICS
R1510SxxxA Series
VIN=14.0V, CE=5.0V, COUT=6.8µF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at -40°C ≤ Ta ≤ 105°C.
For all
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
V
VIN
Input Voltage
3.5
36
Supply Current
(Low-power Consumption Mode)
μA
ISS1
ISS2
I
OUT=0A
12.5
27
μA
μA
°C
Supply Current (High Speed Mode) IOUT=20mA
110
10
174
23
Istandby Standby Current (Standby Mode)
CE=0V
TTSD
TTSR
Thermal Shutdown Temperature
Junction Temperature
140
Thermal Shutdown Released
Temperature
Junction Temperature
125
°C
VR
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
IOUT=1mA
Setting Voltage:
2.5V to 12.0V
Ta=25°C
×0.984
×0.964
×1.016
×1.045
VOUT
Output Voltage
Output Current
V
-40°C ≤ Ta ≤ 105°C
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
IOUT
1
300
mA
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
0.1mA ≤ IOUT ≤ 7mA
(Low-power
Consumption Mode)
VOUT ≤ 5.0V
7
13
20
VOUT > 5.0V
10
ΔVOUT
ΔIOUT
/
mV
Load Regulation
V
OUT ≤ 5.0V
VOUT > 5.0V
OUT ≤ 5.0V
VOUT > 5.0V
OUT < 5.0V
VOUT ≥ 5.0V
OUT < 5.0V
VOUT ≥ 5.0V
10
20
40
60
0.5
45
75
0.1mA ≤ IOUT ≤ 20mA
0.1mA ≤ IOUT ≤ 300mA
V
100
170
1.8
IOUT=7mA
V
(Low-power
Consumption Mode)
0.3
0.95
VDIF
Dropout Voltage
V
V
1.5
1.0
3.2
2.0
IOUT=300mA
High Speed Mode
Switching Current
IOUTH
I
OUT=Light Load to Heavy Load
8.5
1
12
3
16.3
5
mA
mA
Low-power
Consumption Mode
Switching Current
IOUTL
IOUT=Heavy Load to Light Load
3.5V ≤ VIN ≤ 36V (2.5V ≤ VOUT ≤ 3.5V)
ΔVOUT
ΔVIN
/
/
Line Regulation
VOUT+0.5V ≤ VIN ≤ 36V (VOUT > 3.5V)
0.01
0.05
%/V
IOUT=1mA
ΔVOUT
ΔTa
Output Voltage
Temperature Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±150
5
R1510S
NO.EA-185-140724
VIN=14.0V, CE=5.0V, COUT=6.8µF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at -40°C ≤ Ta ≤ 105°C.
VR (Continued)
(Ta=25°C)
Symbol
ISC
Item
Conditions
Min.
Typ.
Max.
Unit
mA
V
Short Current Limit
CE Input Voltage “H”
CE Input Voltage “L”
VOUT=0V
50
VCEH
VCEL
1.5
5.5
0.7
V
VD
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN Detector
Setting Voltage
Range:
Ta=25°C
×0.983
×1.017
-VDET
Detector Threshold
V
-40°C ≤ Ta ≤ 105°C
×0.97
×1.03
2.3 V to 12.0V
-VDET
-VDET
-VDET
Detector Threshold
Hysteresis
VHYS
VDDL
V
V
×0.025 ×0.05 ×0.075
Minimum Operating
Voltage*1
1.8
V
IN ≥ 1.8V, DOUT=0.1V
0.59
1.16
1.39
Output Current
(Nch Driver)
IOUT
2
mA
VIN ≥ 3.0V, DOUT=0.1V
VIN ≥ 4.0V, DOUT=0.1V
Nch Driver Leakage
Current
ILEAK
DOUT=7V
0.33
5.5
μA
VRESET
Pull-up Voltage
V
Detector Threshold
Temperature
Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
Δ-VDET/ΔTa
±100
Release Output
Delay Time*2
tPLH
20
μs
All test items listed under Electrical Characteristics are done under the pulse load condition (Tj≈Ta=25°C) except
Output Voltage Temperature Coefficient and Detector Threshold Temperature Coefficient.
∗1) Minimum operating voltage is defined as the power supply voltage of which output voltage becomes lower
than 0.1V at the detection.
∗2) Release output delay time is defined as the time to be taken for VIN to change from 2V to (-VDET) +1V, and
for DOUT output to become “H”.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the recommended
operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the
semiconductor devices may receive serious damage when they continue to operate over the recommended operating
conditions.
6
R1510S
NO.EA-185-140724
R1510SxxxB Series
VIN=SENSE=14.0V, COUT=6.8μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at -40°C ≤ Ta ≤ 105°C.
For all
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN
Input Voltage
3.5
36
V
Supply Current
(Low-power Consumption Mode)
ISS1
IOUT=0A
12.5
22
μA
ISS2
Supply Current (High Speed Mode) IOUT=20mA
110
140
174
μA
TTSD
Thermal Shutdown Temperature
Junction Temperature
°C
Thermal Shutdown Released
Temperature
TTSR
Junction Temperature
125
°C
VR
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
IOUT=1mA
Setting Voltage:
2.5V to 12.0V
Ta=25°C
×0.984
×1.016
VOUT
Output Voltage
Output Current
V
-40°C ≤ Ta ≤ 105°C
×0.964
×1.045
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
IOUT
1
300
mA
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
0.1mA ≤ IOUT ≤ 7mA
(Low-power
Consumption Mode)
V
OUT ≤ 5.0V
7
13
20
VOUT > 5.0V
10
ΔVOUT
ΔIOUT
/
mV
Load Regulation
VOUT ≤ 5.0V
VOUT > 5.0V
VOUT ≤ 5.0V
VOUT > 5.0V
10
20
40
60
0.5
45
75
0.1mA ≤ IOUT ≤ 20mA
0.1mA ≤ IOUT ≤ 300mA
100
170
1.8
IOUT=7mA
(Low-power
Consumption Mode)
V
OUT < 5.0V
VOUT ≥ 5.0V
OUT < 5.0V
VOUT ≥ 5.0V
0.3
1.5
1.0
0.95
3.2
VDIF
Dropout Voltage
V
V
IOUT=300mA
2.0
High Speed Mode
Switching Current
IOUTH
IOUTL
I
OUT = Light Load to Heavy Load
OUT = Heavy Load to Light Load
8.5
1
12
3
16.3
5
mA
mA
Low-power Consumption
Mode Switching Current
I
3.5V ≤ VIN ≤ 36V (2.5V ≤ VOUT ≤ 3.5V)
VOUT+0.5V ≤ VIN ≤ 36V (VOUT > 3.5V)
ΔVOUT
ΔVIN
/
/
Line Regulation
0.01
0.05
%/V
IOUT=1mA
ΔVOUT
ΔTa
Output Voltage
Temperature Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±150
ISC
Short Current Limit
VOUT=0V
50
mA
7
R1510S
NO.EA-185-140724
VIN=SENSE=14.0V, COUT=6.8μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at -40°C ≤ Ta ≤ 105°C.
VD
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN Detector
Setting Voltage:
2.3 V to 12.0V
Ta=25°C
×0.983
×1.017
-VDET
Detector Threshold
V
V
-40°C ≤ Ta ≤ 105°C
×0.97
×1.03
-VDET
-VDET
-VDET
Detector Threshold
Hysteresis
VHYS
×0.025 ×0.05 ×0.075
-VDET < 6.0V
1.5
3.6
64
57
RSENSE
VDDL
IOUT
SENSE Resistance
MΩ
V
-VDET ≥ 6.0V
Minimum Operating
Voltage
3.0
VIN ≥ 3.0V, DOUT=0.1V
VIN ≥ 4.0V, DOUT=0.1V
1.16
1.39
Output Current
(Nch Driver)
2
mA
Nch Driver Leakage
Current
ILEAK
D
OUT=7V
0.33
5.5
μA
VRESET
Pull-up Voltage
V
Detector Threshold
Temperature
Coefficient
Δ-VDET
ΔTa
/
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±100
Release Output Delay
Time *1
tPLH
20
μs
SENSE Pin Input
Voltage
VSENSE
36
V
All test items listed under Electrical Characteristics are done under the pulse load condition (Tj≈Ta=25°C) except
Output Voltage Temperature Coefficient and Detector Threshold Temperature Coefficient.
∗1) Release output delay time is defined as the time to be taken for SENSE to change from 2V to (-VDET) +1V,
and for DOUT output to become “H”.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the recommended
operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the
semiconductor devices may receive serious damage when they continue to operate over the recommended operating
conditions.
8
R1510S
NO.EA-185-140724
R1510SxxxC Series
VIN=14.0V, COUT=6.8μF, CD=0.01μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at -40°C ≤ Ta ≤ 105°C.
For all
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN
Input Voltage
3.5
36
27
V
Supply Current
(Low-power Consumption Mode)
ISS1
IOUT=0A
12.5
μA
ISS2
Supply Current (High Speed Mode) IOUT=20mA
110
140
174
μA
TTSD
Thermal Shutdown Temperature
Junction Temperature
°C
Thermal Shutdown Released
Temperature
TTSR
Junction Temperature
125
°C
VR
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
IOUT=1mA
Setting Voltage:
2.5V to 12.0V
Ta=25°C
×0.984
×1.016
VOUT
Output Voltage
Output Current
V
-40°C ≤ Ta ≤ 105°C
×0.964
×1.045
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
IOUT
1
300
mA
mV
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
0.1mA ≤ IOUT ≤ 7mA
(Low-power
Consumption Mode)
V
OUT ≤ 5.0V
7
13
20
VOUT > 5.0V
10
ΔVOUT
ΔIOUT
/
Load Regulation
VOUT ≤ 5.0V
10
20
40
60
45
75
0.1mA ≤ IOUT ≤ 20mA
0.1mA ≤ IOUT ≤ 300mA
VOUT > 5.0V
V
OUT ≤ 5.0V
VOUT > 5.0V
OUT < 5.0V
100
170
IOUT=7mA
(Low-power
Consumption Mode)
V
0.5
0.3
1.5
1.0
1.8
0.95
3.2
VOUT ≥ 5.0V
VOUT < 5.0V
VOUT ≥ 5.0V
VDIF
Dropout Voltage
V
IOUT=300mA
2.0
High Speed Mode
Switching Current
IOUTH
IOUTL
I
OUT=Light Load to Heavy Load
OUT=Heavy Load to Light Load
8.5
1
12
3
16.3
5
mA
mA
Low-power Consumption
Mode Switching Current
I
3.5V ≤ VIN ≤ 36V (2.5V ≤ VOUT ≤ 3.5V)
VOUT+0.5V ≤ VIN ≤ 36V (VOUT > 3.5V)
ΔVOUT
ΔVIN
/
/
Line Regulation
0.01
0.05
%/V
IOUT=1mA
ΔVOUT
ΔTa
Output Voltage
Temperature Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±150
ISC
Short Current Limit
VOUT=0V
50
mA
9
R1510S
NO.EA-185-140724
VIN=14.0V, COUT=6.8μF, CD=0.01μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at - 40°C ≤ Ta ≤ 105°C.
VD
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN Detector
Ta=25°C
×0.983
×1.017
-VDET
Detector Threshold Setting Voltage:
2.3 V to 12.0V
V
-40°C ≤ Ta ≤ 105°C
×0.97
×1.03
-VDET
-VDET
-VDET
Detector Threshold
Hysteresis
VHYS
VDDL
V
V
×0.025 ×0.05 ×0.075
Minimum Operating
Voltage *1
1.8
VIN ≥ 1.8V, DOUT=0.1V
VIN ≥ 3.0V, DOUT=0.1V
VIN ≥ 4.0V, DOUT=0.1V
0.59
1.16
1.39
Output Current
(Nch Driver)
IOUT
2
mA
Nch Driver Leakage
Current
ILEAK
D
OUT=7V
0.33
5.5
μA
VRESET
Pull-up Voltage
V
Detector Threshold
Temperature
Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
Δ-VDET/ΔTa
±100
Release Output
Delay Time*2
tdelay
35
70
150
ms
All test items listed under Electrical Characteristics are done under the pulse load condition (Tj≈Ta=25°C) except
Output Voltage Temperature Coefficient and Detector Threshold Temperature Coefficient.
∗1) Minimum operating voltage is defined as the power supply voltage of which output voltage becomes lower
than 0.1V at the detection.
∗2) Release output delay time is defined as the time to be taken for VIN to change from 2V to (-VDET) +1V, and
also for DOUT output to become “H”.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the recommended
operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the
semiconductor devices may receive serious damage when they continue to operate over the recommended operating
conditions.
10
R1510S
NO.EA-185-140724
R1510SxxxD Series
VIN=14.0V, COUT=6.8μF, CD=0.01μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at - 40°C ≤ Ta ≤ 105°C.
For all
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
VIN
Input Voltage
3.5
36
V
Supply Current
(Low-power Consumption Mode)
ISS1
IOUT=0A
12.5
26
μA
ISS2
Supply Current (High Speed Mode) IOUT=20mA
110
140
174
μA
TTSD
Thermal Shutdown Temperature
Junction Temperature
°C
Thermal Shutdown Released
Temperature
TTSR
Junction Temperature
125
°C
VR
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
IOUT=1mA
Setting Voltage:
2.5V to 12.0V
Ta=25°C
×0.984
×1.016
VOUT
Output Voltage
Output Current
V
-40°C ≤ Ta ≤ 105°C
×0.964
×1.045
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
IOUT
1
300
mA
VIN=VOUT+3.2V (VOUT < 5.0V)
VIN=VOUT+2.0V (VOUT ≥ 5.0V)
0.1mA ≤ IOUT ≤ 7mA
(Low-power
Consumption Mode)
V
OUT ≤ 5.0V
7
13
20
VOUT > 5.0V
10
ΔVOUT
ΔIOUT
/
mV
Load Regulation
VOUT ≤ 5.0V
10
20
40
60
45
75
0.1mA ≤ IOUT ≤ 20mA
0.1mA ≤ IOUT ≤ 300mA
VOUT > 5.0V
V
OUT ≤ 5.0V
VOUT > 5.0V
OUT < 5.0V
VOUT ≥ 5.0V
OUT < 5.0V
VOUT ≥ 5.0V
100
170
IOUT=7mA
(Low-power
Consumption Mode)
V
0.5
0.3
1.5
1.0
1.8
0.95
3.2
VDIF
Dropout Voltage
V
V
IOUT=300mA
2.0
High Speed Mode
Switching Current
IOUTH
IOUTL
I
OUT=Light Load to Heavy Load
8.5
1
12
3
16.3
5
mA
mA
Low-power Consumption
Mode Switching Current
IOUT=Heavy Load to Light Load
3.5V ≤ VIN ≤ 36V (2.5V ≤ VOUT ≤ 3.5V)
VOUT+0.5V ≤ VIN ≤ 36V (VOUT > 3.5V)
IOUT=1mA
ΔVOUT
ΔVIN
/
/
Line Regulation
0.01
0.05
%/V
ΔVOUT
ΔTa
Output Voltage
Temperature Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±150
ISC
Short Current Limit
VOUT=0V
50
mA
11
R1510S
NO.EA-185-140724
VIN=14.0V, COUT=6.8μF, CD=0.01μF, Rpull-up=100kΩ, Vpull-up=5.0V, unless otherwise noted.
The specifications surrounded by
are guaranteed by design engineering at - 40°C ≤ Ta ≤ 105°C.
VD
(Ta=25°C)
Symbol
Item
Conditions
Min.
Typ.
Max. Unit
VIN Detector
Setting Voltage:
2.3 V to 10.6V
Ta=25°C
×0.983
×1.017
-VDET
Detector Threshold
V
-40°C ≤ Ta ≤ 105°C
×0.97
×1.03
-VDET
-VDET
V
-VDET
VHYS
VDDL
Detector Threshold Hysteresis
Minimum Operating Voltage*1
×0.025 ×0.05 ×0.075
1.8
V
V
IN ≥ 1.8V, DOUT=0.1V
0.59
1.16
1.39
0.33
5.5
Output Current
(Nch Driver)
IOUT
2
VIN ≥ 3.0V, DOUT=0.1V
VIN ≥ 4.0V, DOUT=0.1V
DOUT=7V
mA
ILEAK
Nch Driver Leakage Current
Pull-up Voltage
μA
VRESET
V
Δ-VDET
ΔTa
/
Detector Threshold
Temperature Coefficient
ppm
/°C
-40°C ≤ Ta ≤ 105°C
±100
tdelay
Release Output Delay Time *2
35
70
150
ms
All test items listed under Electrical Characteristics are done under the pulse load condition (Tj≈Ta=25°C) except
Output Voltage Temperature Coefficient and Detector Threshold Temperature Coefficient.
∗1) Minimum operating voltage is defined as the power supply voltage of which output voltage becomes lower
than 0.1V at the detection.
∗2) Release output delay time is defined as the time to be taken for VOUT to change from 2V to (-VDET) +1V, and
also for DOUT output to become “H”.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the recommended
operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the
semiconductor devices may receive serious damage when they continue to operate over the recommended operating
conditions.
12
R1510S
NO.EA-185-140724
Product-specific Electrical Characteristics
The specifications surrounded by
are guaranteed by design engineering at −40°C ≤ Ta ≤ 105°C.
VR
(Ta = 25°C)
VOUT [V]
VDIF [V]
(IOUT = 7 mA:
Low-power
Product Name
(Ta = 25°C)
(Ta = −40 to 105°C)
(IOUT = 300 mA)
Consumption Mode)
MIN.
3.248
2.460
TYP.
3.300
2.500
MAX.
3.352
2.540
MIN.
3.182
2.410
11.568
5.399
3.182
3.182
4.820
3.182
11.568
3.471
4.820
4.820
4.820
MAX.
3.448
2.612
12.540
5.852
3.448
3.448
5.225
3.448
12.540
3.762
5.225
5.225
5.225
TYP.
0.5
0.5
0.3
0.3
0.5
0.5
0.3
0.5
0.3
0.5
0.3
0.3
0.3
MAX.
1.8
TYP.
1.5
1.5
1.0
1.0
1.5
1.5
1.0
1.5
1.0
1.5
1.0
1.0
1.0
MAX.
3.2
3.2
2.0
2.0
3.2
3.2
2.0
3.2
2.0
3.2
2.0
2.0
2.0
R1510S001x
R1510S002x
R1510S003x
R1510S004x
R1510S005x
R1510S006x
R1510S007x
R1510S008x
R1510S009x
R1510S010x
R1510S011x
R1510S012x
R1510S013x
1.8
11.808 12.000 12.192
0.95
0.95
1.8
5.511
3.248
3.248
4.920
3.248
5.600
3.300
3.300
5.000
3.300
5.689
3.352
3.352
5.080
3.352
1.8
0.95
1.8
11.808 12.000 12.192
0.95
1.8
3.543
4.920
4.920
4.920
3.600
5.000
5.000
5.000
3.657
5.080
5.080
5.080
0.95
0.95
0.95
VR (Continued)
(Ta = 25°C)
∆VOUT / ∆IOUT [mV]
(0.1 mA ≤ IOUT ≤ 20 mA)
(0.1 mA ≤ IOUT ≤ 7 mA:
Low-power
Product Name
(0.1 mA ≤ IOUT ≤ 300 mA)
Consumption Mode)
MIN.
7
MAX.
13
13
20
20
13
13
13
13
20
13
13
13
13
TYP.
10
10
20
20
10
10
10
10
20
10
10
10
10
MAX.
45
45
75
75
45
45
45
45
75
45
45
45
45
TYP.
40
40
60
60
40
40
40
40
60
40
40
40
40
MAX.
100
100
170
170
100
100
100
100
170
100
100
100
100
R1510S001x
R1510S002x
R1510S003x
R1510S004x
R1510S005x
R1510S006x
R1510S007x
R1510S008x
R1510S009x
R1510S010x
R1510S011x
R1510S012x
R1510S013x
7
10
10
7
7
7
7
10
7
7
7
7
13
R1510S
NO.EA-185-140724
The specifications surrounded by
are guaranteed by design engineering at −40°C ≤ Ta ≤ 105°C.
VD
(Ta = 25°C)
-VDET [V]
(Ta = 25°C)
TYP.
-VDET [V]
VHYS [V]
Product Name
MIN.
(Ta = −40 to 105°C)
MAX.
2.745
4.169
5.085
3.051
3.864
3.661
4.576
2.847
4.271
4.373
2.339
4.271
10.170
MIN.
2.619
3.977
4.850
2.910
3.686
3.492
4.365
2.716
4.074
4.171
2.231
4.074
9.700
MAX.
2.781
4.223
5.150
3.090
3.914
3.708
4.635
2.884
4.326
4.429
2.369
4.326
10.300
MIN.
0.068
0.103
0.125
0.075
0.095
0.090
0.113
0.070
0.105
0.108
0.058
0.105
0.250
TYP.
0.135
0.205
0.250
0.150
0.190
0.180
0.225
0.140
0.210
0.215
0.115
0.210
0.500
MAX.
0.203
0.308
0.375
0.225
0.285
0.270
0.338
0.210
0.315
0.323
0.173
0.315
0.750
R1510S001x
R1510S002x
R1510S003x
R1510S004x
R1510S005x
R1510S006x
R1510S007x
R1510S008x
R1510S009x
R1510S010x
R1510S011x
R1510S012x
R1510S013x
2.655
4.031
4.915
2.949
3.736
3.539
4.424
2.753
4.129
4.227
2.261
4.129
9.830
2.700
4.100
5.000
3.000
3.800
3.600
4.500
2.800
4.200
4.300
2.300
4.200
10.000
14
R1510S
NO.EA-185-140724
TYPICAL APPLICATIONS
R1510SxxxA
R1510SxxxB
VOUT
VOUT
VOUT
NC
VDD
VOUT
NC
VDD
CIN
CIN
COUT
VIN
COUT
VIN
GND
GND
R1510SxxxA
SERIES
R1510SxxxB
SERIES
TP
TP
CE
TP
TP
DOUT
DOUT SENSE
VCE
VSENSE
R
pull-up
pull-up
R
pull-up
pull-up
V
V
R1510SxxxC/D
VOUT
VOUT
NC
VDD
CIN
COUT
VIN
GND
R1510SxxxC/D
SERIES
TP
TP
CD
CIN=0.1μF, COUT=6.8μF (Ceramic)
Rpull-up=100kΩ
DOUT
CD
R
pull-up
pull-up
V
TECHNICAL NOTES
Phase Compensation
This IC is using the capacitance of output capacitor (COUT) and the ESR as phase compensation for the stable
operation of the IC even if the output load varies. Therefore, please make sure to use a capacitor (COUT) with
6.8µF or more.
If the ESR value is large, the output may result in unstable, therefore, please make full evaluation on the
temperature characteristics and the frequency characteristics.
PCB Layout and GND Wiring
The high impedances of VDD and GND could be a reason for the noise pickup and unstable operation. Therefore,
make the impedances of VDD and GND as low as possible. A capacitor (CIN) with 0.1µF or more has to be
connected between VDD pin and GND pin, and the wirings between them have to be short as possible. The
capacitor (COUT) for phase compensation has to be connected between VOUT pin and GND pin, and the wirings
between them have to be short as possible.
15
R1510S
NO.EA-185-140724
OPERATION MANUAL
Voltage Regulator (VR)
Voltage Regulator (VR) operates within the input voltage range of 3.5V to 36V. The output voltage is adjustable
within the range of 2.5V to 12V by 0.1V step. By changing the current value of the control circuit according to the
load current, the supply current at the light load condition can be minimized and also be able to achieve high
speed response. When the load current becomes 12mA (Typ.) or more, the control circuit switches to high-speed
mode and when the load current becomes 3mA or lower, it switches to low-power consumption mode. Hysteresis
is set for the output current between 3mA to 12mA (Typ.).
These current values are internally fixed inside the IC. When the mode switching is caused by the load current
change, the output voltage will be changed as the graph below shows. The load current dependencies (Load
Regulation) of output voltage in Electrical Characteristics have been tested at the following points: 0.1mA, 7mA
(Low-power consumption mode), 20mA, and 300mA.
5.03
5.02
From High-speed Mode to
Low-power consumption Mode
5.01
5.00
From Low-power consumption
4.99
Mode to High-speed Mode
4.98
4.97
0
10
20
30
40
50
Output Current IOUT (mA)
During the period of 100µsec immediately after High-speed mode is switched to Low-power consumption mode,
the current value (IOUTH), which switches Low-power consumption mode back to High-speed mode, is increased
3 times. Therefore, during this time period, the IC can still operate with Low-power consumption mode even if the
load current is between 12mA to 36mA (Typ.).
R1510SxxxA can turn on and off the operation of VR by CE pin.
Voltage Detector (VD)
Voltage Detector (VD) operates within the input voltage range of 1.8V to 36V (R1510SxxxA/C/D) and 3.0V to
36V (R1510SxxxB). The detector threshold is adjustable in the range of 2.3V to 12V by 0.1V step. If the monitor
voltage is lower than the detector threshold, DOUT outputs “L”. In the case of R1510SxxA/B, if the monitor voltage
becomes more than the released voltage, DOUT outputs “H”. In the case of R1510SxxxC/D, if the monitor voltage
becomes more than the released voltage, the capacitor of the release output delay time pin (CD) starts to get
charged. DOUT output maintains “L” until CD reaches to the threshold value. Once CD value becomes more than
the threshold value, DOUT outputs “H”. In the case of R1510SxxxC/D, if the monitor voltage becomes lower than
the detector threshold, the capacitor of CD starts to get discharged. Therefore, if the monitor voltage becomes
more than the released voltage without electrical discharge, the release output delay time afterwards becomes
less than the existing release output delay time (tDELAY).
16
R1510S
NO.EA-185-140724
Release Voltage (+VDET
Detector Threshold (-VDET
)
Monitor Voltage
(VDD or VOUT
)
)
GND
GND
Delay Pin Voltage
(CD)
GND
High level
Output Voltage
Low level
(DOUT
)
Release Output Delay Time (tDELAY
)
Detect Output Delay Time (tRESET)
R1510SxxxC/D
If VIN voltage is raised suddenly from the less than the minimum operating voltage to the less than the release
voltage, VIN voltage momentarily passes through the unstable range (from 0V to the minimum operating voltage),
therefore, DOUT may output “H” (unstable) once then output “L” afterwards. Similarly, if VIN voltage is raised from
the less than the minimum operating voltage to the more than the release voltage, VIN momentarily passes through
the unstable range (from 0V to the minimum operating voltage), therefore, DOUT may output “H” once.
17
R1510S
NO.EA-185-140724
Release Output Delay Time
The release output delay time (Power-on Reset Time (tDELAY)) of R1510SxxxC/D can be set by the capacitor of
CD pin. The relationship between the capacitor capacitance and tDELAY is as shown in the following equation.
tDELAY(s)=7.0×105×CD(F)
The upper limit of the capacitance value for the CD pin capacitor is 1µF. The capacitor operates normally with
more than 1µF; however, if the setting time (tDELAY) is set longer, the setting time differences could become bigger.
Also, if the detect output delay time becomes longer; the response of the VD output pin will be slow to make a
momentary stop.
If the VDD pin voltage is decreased with more than the through rate as it is shown in the graph below, the IC
does not operate normally. If there’s any possibility of this, please minimize the voltage fluctuation of VDD pin by
using CIN.
100
Inp
VDD
t
10
Vpp
1
The detector cannot
maintain the
detection.
0.1
tf
VDD Input Waveform
0.01
0
1
2
3
4
5
6
7
8
9 10 11 12
Vpp (V)
Thermal Shutdown
If the junction temperature (Tj) becomes more than 140°C(Typ.) due to the heat generation in the voltage
regulator, the output driver will be turned off to protect the IC and the voltage regulator output will be turned off. If
the junction temperature becomes less than 125°C(Typ.), the output driver will be turned on and the voltage
regulator output will be turned on. Unless the cause of the heat generation is not removed, the voltage regulator
repeats turns on and off, so the output voltage will be a pulsing form.
R1510SxxxD Voltage Setting
The voltage detector (VD) of R1510SxxxD detects the output voltage drop of the voltage regulator (VR). If the
VD release voltage is set to more than the VR output voltage, the VD will not be canceled even if the VR output
voltage returns to the normal value after VD detected the output voltage drop of VR. To avoid this, there have to
be voltage differences between the voltage regulator’s output voltage (VOUT) and the voltage detector’s release
voltage (+VDET). Also, the following conditions have to be met.
(VR Output Setting Voltage) x 0.964 > (VD Detect Setting Voltage) x1.03 x 1.075
In case of using the products with the VR output voltage and the VD detector threshold that is not met the above
conditions, please make sure to give greater consideration on the system operation before use.
18
R1510S
NO.EA-185-140724
PACKAGE INFORMATION
POWER DISSIPATION (HSOP-8E)
Power Dissipation (PD) depends on conditions of mounting on board.
This specification is based on the measurement at the condition below:
Measurement conditions
Ultra High Wattage land pattern
Environment
Board Material
Mounting on board (Wind velocity=0m/s)
Glass cloth epoxy plastic (4 layers)
76.2mm x 114.3mm x 0.8mm
Board Dimensions
Top side, Back side : 50mm square : Approx.95%
2nd, 3rd Layer: 50mm square : Approx.100%
Copper Ratio
Through – holes
φ 0.4mm x 21pcs
Measurement Results
(Ta=25°C, Tjmax=125°C)
Ultra High Wattage land pattern
Power Dissipation
2.9W
θja = (125-25°C)/2.9W= 35°C/W
θjc=10°C/W
Thermal Resistance
76.2
50
4.0
2.9
3.0
Ultra High Wattage
Land Pattern
2.0
1.0
0
105
0
25
50
75
100 125 150
Measurement Board Pattern
Ambient Temperature (°C)
IC Mount Area (Unit : mm)
Power Dissipation
19
R1510S
NO.EA-185-140724
PACKAGE DIMENSIONS (HSOP-8E)
(0.30)
2.90±0.05
8
5
1
4
0.40±0.1
0.695TYP
5.20±0.3
1.27
M
0.12
DETAIL
A
0.40±0.2
0.10 S
S
DETAIL A
The tab on the bottom of the package enhances thermal
performance and is electrically connected to GND (substrate
level). It is recommended that the tab be connected to the
ground plane on the board, or otherwise be left floating.
(Unit : mm)
MARK SPECIFICATION (HSOP-8E)
①②③④⑤⑥: Product Code … Refer to MARK SPECIFICATION TABLE
⑦⑧⑨: Lot Number … Alphanumeric Serial Number
8
5
cdefgh
ijk
1
4
20
R1510S
NO.EA-185-140724
MARK SPECIFICATION TABLE (HSOP-8E)
R1510SxxxA
R1510SxxxB
VSET
VSET
Product Name
Product Name
cdefgh
cdefgh
VR
VD
2.7V
4.1V
5.0V
3.0V
3.8V
3.6V
4.5V
2.8V
4.2V
4.3V
2.3V
4.2V
10.0V
VR
VD
R1510S001A R S 0 0 3 A
R1510S002A R S 0 0 3 E
3.3V
2.5V
R1510S001B R S 0 0 3 B
R1510S002B R S 0 0 3 F
3.3V
2.5V
2.7V
4.1V
5.0V
3.0V
3.8V
3.6V
4.5V
2.8V
4.2V
4.3V
2.3V
4.2V
R1510S003A R S 0 0 3 J 12.0V
R1510S003B R S 0 0 3 K 12.0V
R1510S004A R S 0 0 3 N
R1510S005A R S 0 0 3 S
R1510S006A R S 0 0 3 W
R1510S007A R S 0 0 4 A
R1510S008A R S 0 0 4 E
5.6V
3.3V
3.3V
5.0V
3.3V
R1510S004B R S 0 0 3 P
R1510S005B R S 0 0 3 T
R1510S006B R S 0 0 3 X
R1510S007B R S 0 0 4 B
R1510S008B R S 0 0 4 F
5.6V
3.3V
3.3V
5.0V
3.3V
R1510S009A R S 0 0 4 J 12.0V
R1510S009B R S 0 0 4 K 12.0V
R1510S010A R S 0 0 4 N
R1510S011A R S 0 0 4 S
R1510S012A R S 0 0 4 W
R1510S013A R S 0 0 6 A
3.6V
5.0V
5.0V
5.0V
R1510S010B R S 0 0 4 P
R1510S011B R S 0 0 4 T
R1510S012B R S 0 0 4 X
3.6V
5.0V
5.0V
R1510SxxxC
R1510SxxxD
VSET
VSET
Product Name
Product Name
cdefgh
cdefgh
VR
VD
VR
VD
R1510S001C R S 0 0 3 C
R1510S002C R S 0 0 3 G
3.3V
2.5V
2.7V
4.1V
5.0V
3.0V
3.8V
3.6V
4.5V
R1510S001D R S 0 0 3 D
3.3V
2.7V
5.0V
3.0V
2.8V
4.2V
2.3V
4.2V
R1510S003D R S 0 0 3 M 12.0V
R1510S003C R S 0 0 3 L 12.0V
R1510S004D R S 0 0 3 R
R1510S008D R S 0 0 4 H
5.6V
3.3V
R1510S004C R S 0 0 3 Q
R1510S005C R S 0 0 3 U
R1510S006C R S 0 0 3 Y
R1510S007C R S 0 0 4 C
5.6V
3.3V
3.3V
5.0V
R1510S009D R S 0 0 4 M 12.0V
R1510S011D R S 0 0 4 V
5.0V
5.0V
R1510S012D R S 0 0 4 Z
*) The followings do not exit:
R1510S008C R S 0 0 4 G
3.3V
2.8V
R1510S002D, 005D, 006D, 007D, 010D
R1510S009C R S 0 0 4 L 12.0V
4.2V
4.3V
2.3V
4.2V
R1510S010C R S 0 0 4 Q
R1510S011C R S 0 0 4 U
R1510S012C R S 0 0 4 Y
3.6V
5.0V
5.0V
21
R1510S
NO.EA-185-140724
TYPICAL CHARACTERISTICS
Note: Typical Characteristics are intended to be used as reference data; they are not guaranteed.
1) Output Voltage vs. Output Current (Ta=25°C)
R1510S (VR=2.5V)
R1510S (VR=5.0V)
6.0
5.0
4.0
3.0
2.0
1.0
0.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
VIN=6.0V
VIN=6.5V
VIN=7.0V
VIN=7.5V
VIN=8.0V
VIN=4.0V
VIN=4.5V
VIN=5.0V
VIN=5.5V
VIN=6.0V
0
100 200 300 400 500 600 700
Output Current IOUT (mA)
0
100 200 300 400 500 600 700
Output Current IOUT (mA)
R1510S (VR=12.0V)
14
12
10
8
VIN=12.4V
VIN=12.6V
VIN=12.8V
VIN=13.0V
VIN=13.2V
6
4
2
0
0
100 200 300 400 500 600 700
Output Current IOUT (mA)
2) Output Voltage vs. Input Voltage (Ta=25°C)
R1510S (VR=2.5V)
R1510S (VR=5.0V)
6
5
4
3
2
1
0
3.0
2.5
2.0
1.5
1.0
IOUT=1mA
IOUT=1mA
IOUT=20mA
0.5
IOUT=20mA
IOUT=100mA
IOUT=100mA
0.0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
Input Voltage VIN (V)
Input Voltage VIN (V)
22
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
14
12
10
8
6
4
IOUT=1mA
IOUT=20mA
IOUT=100mA
2
0
0
2
4
6
8
10
12
14
Input Voltage VIN (V)
3) Dropout Voltage vs. Output Current
R1510S (VR=2.5V)
R1510S (VR=5.0V)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
3.5
-40°C
25°C
1
105°C
-40°C
3.0
25°C
105°C
2.5
2.0
1.5
1.0
0.5
0.0
0
50
100
150
200
250
300
0
50
100
150
200
250
300
Output Current IOUT (mA)
Output Current IOUT (mA)
R1510S (VR=12.0V)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
-40°C
25°C
1
105°C
0
50
100
150
200
250
300
Output Current IOUT (mA)
23
R1510S
NO.EA-185-140724
4) Output Voltage vs. Output Current (Ta=25°C)
R1510S (VR=2.5V)
R1510S (VR=5.0V)
5.03
5.02
5.01
5.00
4.99
4.98
4.97
2.53
2.52
2.51
2.50
2.49
2.48
2.47
0
10
20
30
40
50
0
10
20
30
40
50
Output Current IOUT (mA)
Output Current IOUT (mA)
R1510S (VR=12.0V)
12.06
12.04
12.02
12.00
11.98
11.96
11.94
0
10
20
30
40
50
Output Current IOUT (mA)
5) Output Voltage vs. Operating Temperature
R1510S (VR=2.5V)
R1510S (VR=5.0V)
2.60
5.20
5.15
5.10
5.05
5.00
4.95
4.90
4.85
4.80
IOUT=1mA
IOUT=1mA
2.58
2.56
2.54
2.52
2.50
2.48
2.46
2.44
2.42
2.40
IOUT=20mA(HS)
IOUT=20mA(HS)
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
Temperature Topt (°C)
24
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
12.5
12.4
12.3
12.2
12.1
12.0
11.9
11.8
11.7
11.6
11.5
IOUT=1mA
IOUT=20mA(HS)
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
6) Supply Current vs. Input Voltage
R1510S (VR=2.5V, VD=2.3V)
R1510S (VR=5.0V, VD=4.5V)
160
140
120
100
80
160
IOUT=0mA(ECO)
IOUT=20mA(HS)
IOUT=0mA(ECO)
140
IOUT=20mA(HS)
120
100
80
60
40
20
0
60
40
20
0
0
4
8
12 16 20 24 28 32 36
0
4
8
12 16 20 24 28 32 36
Input Voltage VIN (V)
Input Voltage VIN (V)
R1510S (VR=12.0V, VD=11.0V)
160
140
120
100
80
IOUT=0mA(ECO)
IOUT=20mA(HS)
60
40
20
0
0
4
8
12 16 20 24 28 32 36
Input Voltage VIN (V)
25
R1510S
NO.EA-185-140724
7) Supply Current vs. Operating Temperature
R1510SxxxA
R1510SxxxB
VIN=14V
OUT=0mA
VIN=14V
OUT=0mA
VR=2.5V, VD=2.3V
I
I
30
25
20
15
10
5
30
25
20
15
10
5
VR=2.5V, VD=2.3V
VR=5.0V, VD=4.5V
VR=12.0V, VD=11.0V
VR=5.0V, VD=4.5V
VR=12.0V, VD=11.0V
0
0
-50 -25
0
25
50
75
100 125
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
Temperature Topt (°C)
R1510SxxxC
R1510SxxxD
VIN=14V
IOUT=0mA
VR=2.5V, VD=2.3V
VIN=14V
IOUT=0mA
30
30
VR=2.5V, VD=2.3V
25
20
15
10
5
25
20
15
10
5
VR=5.0V, VD=4.5V
VR=5.0V, VD=4.5V
VR=12.0V, VD=11.0V
VR=12.0V, VD=11.0V
0
0
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
Temperature Topt (°C)
8) Supply Current vs. Output Current (Ta=25°C)
R1510SxxxA (VR=5.0V)
VIN=7V
300
250
200
150
100
50
0
0.1
1
10
100
1000
Output Current IOUT (mA)
26
R1510S
NO.EA-185-140724
9) Mode Switching Load Current vs. Operating Temperature
R1510S
VIN=14V
14
12
10
8
6
4
2
0
ECO HS
→
HS ECO
→
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
10) Dropout Voltage vs. Set Output Voltage (Ta=25°C)
R1510S
2.5
IOUT=1mA
IOUT=10mA(ECO)
IOUT=20mA
2.0
IOUT=50mA
IOUT=100mA
IOUT=300mA
1.5
1.0
0.5
0.0
0.0
2.0
4.0
6.0
8.0
10.0 12.0
Set Output Voltage VREG (V)
11) Ripple Rejection vs. Frequency (Ta=25°C)
R1510S (VR=2.5V)
R1510S (VR=5.0V)
V
IN=6V+0.2Vp-p
VIN=7V+0.2Vp-p
80
70
60
50
40
30
20
80
70
60
50
40
30
20
IOUT=1mA
IOUT=1mA
IOUT=100mA
IOUT=100mA
0.1
1
10
100
0.1
1
10
100
Frequency f (kHz)
Frequency f (kHz)
27
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
VIN=14V+0.2Vp-p
80
70
60
50
40
30
20
IOUT=1mA
IOUT=100mA
0.1
1
10
100
Frequency f (kHz)
12) Ripple Rejection vs. Input Voltage (Ta=25°C)
R1510S (VR=2.5V)
R1510S (VR=2.5V)
I
OUT=1mA
IOUT=100mA
Ripple=0.2Vp-p
Ripple=0.2Vp-p
80
70
60
50
40
30
20
80
70
60
50
40
30
20
1kHz
10kHz
100kHz
1kHz
10kHz
100kHz
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Input Voltage VIN (V)
Input Voltage VIN (V)
R1510S (VR=5.0V)
R1510S (VR=5.0V)
IOUT=1mA
IOUT=100mA
Ripple=0.2Vp-p
Ripple=0.2Vp-p
80
70
60
50
40
30
20
80
1kHz
10kHz
100kHz
70
60
50
40
30
20
1kHz
10kHz
100kHz
5.0
5.5
6.0
6.5
7.0
7.5
5.0
5.5
6.0
6.5
7.0
7.5
Input Voltage VIN (V)
Input Voltage VIN (V)
28
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
R1510S (VR=12.0V)
IOUT=100mA
Ripple=0.2Vp-p
IOUT=1mA
Ripple=0.2Vp-p
80
70
60
50
40
30
20
1kHz
10kHz
100kHz
1kHz
10kHz
100kHz
80
70
60
50
40
30
20
12.0
12.5
13.0
13.5
14.0
14.5
12.0
12.5
13.0
13.5
14.0
14.5
Input Voltage VIN (V)
Input Voltage VIN (V)
13) Input Transient Response (Ta=25°C)
R1510S (VR=2.5V)
VDD=3.5V to 4.5V, COUT=6.8μF, IOUT=1mA,tf, tr=1μs
5.0
4.5
4.0
3.5
3.0
Input Voltage
2.52
2.51
2.50
2.49
2.48
Output Voltage
-100
0
100
200
300
400
500
600
700
800
Time (μs)
R1510S (VR=5.0V)
VDD=6V to 7V, COUT=6.8μF, IOUT=1mA, tf,tr=1μs
7.5
7.0
6.5
6.0
5.5
Input Voltage
Output Voltage
5.01
5.00
4.99
4.98
-100
0
100
200
300
400
500
600
700
800
Time (μs)
29
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
VDD=13V to 14V, COUT=6.8μF, IOUT=1mA, tf,tr=1μs
14.5
14.0
13.5
13.0
12.5
Input Voltage
12.03
12.02
12.01
12.00
11.99
11.98
Output Voltage
-100
0
100
200
300
400
500
600
700
800
Time (μs)
R1510S (VR=2.5V)
VDD=3.5V to 4.5V, COUT=6.8μF, IOUT=10mA(HS), tf,tr=1μs
5.0
4.5
4.0
3.5
3.0
Input Voltage
2.52
2.51
2.50
2.49
2.48
Output Voltage
-100
0
100
200
300
400
500
600
700
800
Time (μs)
R1510S (VR=5.0V)
VDD=6V to 7V, COUT=6.8μF, IOUT=10mA(HS), tf,tr=1μs
7.5
7.0
6.5
6.0
5.5
Input Voltage
5.03
5.02
5.01
5.00
4.99
4.98
Output Voltage
-100
0
100
200
300
400
500
600
700
800
Time (μs)
30
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
VDD=13V to 14V, COUT=6.8μF, IOUT=10mA(HS), tf,tr=1μs
14.5
14.0
13.5
13.0
12.5
Input Voltage
12.03
12.02
12.01
12.00
11.99
11.98
Output Voltage
-100
0
100
200
300
400
500
600
700
800
Time (μs)
14) Load Transient Response (Ta=25°C)
R1510S (VR=2.5V)
VDD=5.5V, C =2.2μF, COUT=6.8μF, IOUT=0mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
Output Voltage
3.0
2.5
2.0
1.5
-40
0
40
80
120
160
200
240
Time (μs)
R1510S (VR=5.0V)
VDD=7.0V, C =2.2μF, COUT=6.8μF, IOUT=0mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
Output Voltage
5.5
5.0
4.5
4.0
-40
0
40
80
120
160
200
240
Time (μs)
31
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
VDD=14V, C =2.2μF, COUT=6.8μF, IOUT=0mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
Output Voltage
12.5
12.0
11.5
11.0
-40
0
40
80
120
160
200
240
Time (μs)
R1510S (VR=2.5V)
VDD=5.5V, C =2.2μF, COUT=6.8μF, IOUT=20mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
Output Voltage
3.0
2.5
2.0
1.5
-40
0
40
80
120
160
200
240
Time (μs)
R1510S (VR=5.0V)
VDD=7V, C =2.2μF, COUT=6.8μF, IOUT=20mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
Output Voltage
5.5
5.0
4.5
4.0
-40
0
40
80
120
160
200
240
Time (μs)
32
R1510S
NO.EA-185-140724
R1510S (VR=12.0V)
VDD=14V, C =2.2μF, COUT=6.8μF, IOUT=20mA to 300mA, tf,tr=1μs
IN
600
300
0
Output Current
12.5
12.0
11.5
11.0
VR Output Voltage
-40
0
40
80
120
160
200
240
Time (μs)
15) Start-up Waveform (Ta=25°C)
R1510SxxxB/C/D (VR=5.0V)
COUT=6.8μF, IOUT=10mA, tf,tr=1μs
8
7
6
5
4
3
2
1
0
800
700
600
500
400
300
200
100
0
VIN
VOUT
Inrush Current
-50
0
50
100
150
200
250
Time (μs)
16)Start-up Waveform by CE (Ta=25°C)
R1510SxxxA (VR=5.0V)
VIN=7V, IOUT=10mA
8
7
6
5
4
3
2
1
0
800
700
600
500
400
300
200
100
0
CE
VOUT
Inrush Current
-50
0
50
100
150
200
Time (μs)
33
R1510S
NO.EA-185-140724
17) Thermal Shutdown
R1510S (VR=5.0V)
VIN=14V, IOUT=1mA
6
5
4
3
2
1
0
50 60 70 80 90 100 110 120 130 140 150
Temperature Topt (°C)
18) Detector Threshold Voltage vs. Operating Temperature
R1510S (VD=2.3V)
R1510S (VD=4.8V)
5.10
2.42
2.40
2.38
2.36
2.34
2.32
2.30
2.28
5.05
5.00
4.95
4.90
4.85
4.80
4.75
-VDET
-VDET
+VDET
+VDET
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
Temperature Topt (°C)
R1510S (VD=12.0V)
12.9
12.8
12.7
12.6
12.5
12.4
12.3
12.2
12.1
12.0
11.9
-VDET
+VDET
-50 -25
0
25
50
75 100 125
Temperature Topt (°C)
34
R1510S
NO.EA-185-140724
19) VD Output Voltage vs. Input Voltage
R1510SxxxA/C/D (VD=2.3V)
R1510SxxxA/C/D (VD=4.8V)
pull up 5V, 470kΩ
pull up 5V, 470kΩ
6
5
4
3
2
1
0
6
5
4
3
2
1
0
-40°C
105°C
25°C
-40°C
25°C
1
0
5
°
C
0.0
0.5
1.0
1.5 2.0
2.5
3.0
3.5
0
1
2
3
4
5
6
7
Input Voltage VIN (V)
Input Voltage VIN (V)
R1510SxxxA/C/D (VD=12.0V)
R1510SxxxB
SENSE=0V, pull up 5V,470kΩ
pull up 5V, 470kΩ
6
5
4
3
2
1
0
6
-40°C
5
4
3
2
1
0
-40°C
105°C
105°C
25°C
25°C
0
2
4
6
8
10
12
14
0
2
4
6
8
10
Input Voltage VIN (V)
Input Voltage VIN (V)
20) DOUT Sink Current vs. DOUT Output Voltage
R1510S
35
VIN=1.0V
30
25
20
15
10
5
VIN=1.5V
VIN=2.0V
VIN=4.0V
0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
DOUT Output Voltage VDS (V)
35
R1510S
NO.EA-185-140724
21) DOUT Sink Current vs. Input Voltage
R1510S (VD=2.3V)
R1510S (VD=4.8V)
DOUT=0.5V
DOUT=0.5V
20
18
16
14
12
10
8
20
18
16
14
12
10
8
-50°C
05°C
25°C
-50°C
105°C
25°C
6
6
4
4
2
2
0
0
0.0
0.5 1.0
1.5
2.0
2.5 3.0
3.5
0
1
2
3
4
5
6
7
Input Voltage VIN (V)
Input Voltage VIN (V)
R1510S (VD=12.0V)
DOUT=0.5V
20
-50°C
105°C
25°C
18
16
14
12
10
8
6
4
2
0
0
2
4
6
8
10
12
14
Input Voltage VIN (V)
22) CD Detector Threshold vs. Operating Voltage
R1510SxxxC/D
23) CD Sink Current vs. CD Output Voltage
R1510SxxxC/D
VIN=14V
VIN =4.5V
3.0
1.6
4.0V
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
2.5
3.5V
2.0
3.0V
1.5
1.0
0.5
0.0
2.5V
2.0V
1.5V
0.0
1.0
2.0
3.0
4.0
-50 -25
0
25
50
75
100 125
Temperature Topt (°C)
CD Output Voltage VDS (V)
36
R1510S
NO.EA-185-140724
24) CD Output Current Vs. Input Voltage
R1510SxxxC/D (VD=2.3V)
R1510SxxxC/D (VD=4.8V)
CD=0.5V
CD=0.5V
2.5
2.0
1.5
1.0
0.5
0.0
0.8
0.6
0.4
0.2
0.0
-40°C
25°C
-40°C
25°C
105°C
105°C
0.0
0.5
1.0
1.5
2.0
2.5
0.0
1.0
2.0
3.0
4.0
5.0
Input Voltage VIN (V)
Input Voltage VIN (V)
R1510SxxxC/D (VD=12.0V)
CD=0.5V
2.5
2.0
1.5
1.0
0.5
0.0
-40°C
25°C
1
105°C
0.0
2.0
4.0
6.0
8.0
10.0 12.0
Input Voltage VIN (V)
25) Output Delay Time vs. Operating Temperature
R1510SxxxA/B
26) Release Output Delay Time vs.
Operating Temperature
R1510SxxxC/D
CD=0.01μF
130
110
90
30
25
PLH
t
20
70
15
10
5
PHL
t
50
30
0
10
-50 -25
0
25
50
75 100 125
-50
-25
0
25
50
75
100 125
Temperature Topt (°C)
Temperature Topt (°C)
37
R1510S
NO.EA-185-140724
27) Output Delay Time vs. External Capacitance of Output Delay Pin
R1510SxxxC/D (VD=2.3V)
R1510SxxxC/D (VD=4.5V)
1000
100
10
1000
100
10
delay
t
delay
t
1
1
0.1
0.1
reset
t
reset
t
0.01
0.01
0.001
0.001
0.001
0.01
0.1
1
10
100
0.001
0.01
0.1
1
10
100
External Capacitance (nF)
External Capacitance (nF)
R1510SxxxC/D (VD=12.0V)
1000
100
10
delay
t
1
0.1
reset
t
0.01
0.001
0.001
0.01
0.1
1
10
100
External Capacitance (nF)
38
R1510S
NO.EA-185-140724
Detection Operation Glitch of SENSE Pin Voltage
The graph below shows that the pulse amplitude/ pulse width that can maintain the released condition when
the pulse of less than the detector threshold voltage was input into SENSE pin.
R1510SxxxB
Topt=25°C
80
70
60
50
VD=12.0V
40
30
20
10
0
VD=2.3V
VD=5.0V
10
100
1000
Amplitude Level (mV)
Pulse Width
SENSE
-VDET
Amplitude Level
SENSE Input Waveform
This graph shows the maximum pulse conditions that can maintain the released condition. Please be careful to
the sizes of the pulse width and the pulse amplitude going into SENSE pin because if they are bigger than the
sizes of the pulse width and the pulse amplitude in this graph, the reset signal may go off.
39
R1510S
NO.EA-185-140724
EQUIVALENT SERIES RESISTANCE vs. OUTPUT CURRENT
Ceramic type output capacitor is recommended for this series, however; low ESR type capacitor also could be
used. For reference, the conditions below show the relationship between the output current (IOUT) of which noise
level is 40µV (average) or less and the ESR.
Measurement Conditions
• Noise Frequency Range: 10Hz to 2MHz
• Ambient Temperature: -40°C to 105°C
• Shaded Area: Noise level is 40µV (average) or less
• Output Capacitor: Ceramic 6.8µF
R1510S (VR=2.5V)
R1510S (VR=5.0V)
VIN=3.5V to 36V, COUT=Ceramic 6.8μF
VIN=6.0V to 36V, COUT=Ceramic 6.8μF
100
10
100
10
25°C
-40°C
105°C
25°C
-40°C
105°C
1
1
0.1
0.01
0.1
0.01
0
50
100
150
200
250
300
0
50
100
150
200
250
300
Output Current IOUT (mA)
Output Current IOUT (mA)
R1510S (VR=12.0V)
VIN=13.0V to 36V, COUT=Ceramic 6.8μF
100
10
25°C
105°C
-40°C
1
0.1
0.01
0
50
100
150
200
250
300
Output Current IOUT (mA)
40
1.The products and the product specifications described in this document are subject to change or
discontinuation of production without notice for reasons such as improvement. Therefore, before
deciding to use the products, please refer to Ricoh sales representatives for the latest information
thereon.
2.The materials in this document may not be copied or otherwise reproduced in whole or in part without
prior written consent of Ricoh.
3.Please be sure to take any necessary formalities under relevant laws or regulations before exporting or
otherwise taking out of your country the products or the technical information described herein.
4.The technical information described in this document shows typical characteristics of and example
application circuits for the products. The release of such information is not to be construed as a
warranty of or a grant of license under Ricoh's or any third party's intellectual property rights or any
other rights.
5.The products listed in this document are intended and designed for use as general electronic
components in standard applications (office equipment, telecommunication equipment, measuring
instruments, consumer electronic products, amusement equipment etc.). Those customers intending to
use a product in an application requiring extreme quality and reliability, for example, in a highly specific
application where the failure or misoperation of the product could result in human injury or death
(aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and
transportation equipment, combustion equipment, safety devices, life support system etc.) should first
contact us.
6.We are making our continuous effort to improve the quality and reliability of our products, but
semiconductor products are likely to fail with certain probability. In order to prevent any injury to
persons or damages to property resulting from such failure, customers should be careful enough to
incorporate safety measures in their design, such as redundancy feature, firecontainment feature and
fail-safe feature. We do not assume any liability or responsibility for any loss or damage arising from
misuse or inappropriate use of the products.
7.Anti-radiation design is not implemented in the products described in this document.
8.Please contact Ricoh sales representatives should you have any questions or comments concerning
the products or the technical information.
Ricoh is committed to reducing the environmental loading materials in electrical devices
with a view to contributing to the protection of human health and the environment.
Ricoh has been providing RoHS compliant products since April 1, 2006 and Halogen-free products since
Halogen Free
April 1, 2012.
http://www.e-devices.ricoh.co.jp/en/
Sales & Spport Offices
RICOH ELECTRONIC DEVICES CO., LTD.
Higashi-Shinagawa Office (International Sales)
3-32-3, Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-8655, Japan
Phone: +81-3-5479-2857 Fax: +81-3-5479-0502
RICOH EUROPE (NETHERLANDS) B.V.
Semiconductor Support Centre
“Nieuw Kronenburg”Prof. W.H. Keesomlaan 1, 1183 DJ, Amstelveen, The Netherlands
P.O.Box 114, 1180 AC Amstelveen
Phone: +31-20-5474-309 Fax: +31-20-5474-791
RICOH ELECTRONIC DEVICES KOREA CO., LTD.
11 floor, Haesung 1 building, 942, Daechidong, Gangnamgu, Seoul, Korea
Phone: +82-2-2135-5700 Fax: +82-2-2135-5705
RICOH ELECTRONIC DEVICES SHANGHAI CO., LTD.
Room403, No.2 Building, 690#Bi Bo Road, Pu Dong New district, Shanghai 201203,
People's Republic of China
Phone: +86-21-5027-3200 Fax: +86-21-5027-3299
RICOH ELECTRONIC DEVICES CO., LTD.
Taipei office
Room109, 10F-1, No.51, Hengyang Rd., Taipei City, Taiwan (R.O.C.)
Phone: +886-2-2313-1621/1622 Fax: +886-2-2313-1623
相关型号:
©2020 ICPDF网 联系我们和版权申明