R5107G3411C-TR-JE [RICOH]
Power Supply Management Circuit,;型号: | R5107G3411C-TR-JE |
厂家: | RICOH ELECTRONICS DEVICES DIVISION |
描述: | Power Supply Management Circuit, |
文件: | 总21页 (文件大小:775K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
R5107G SERIES
AEC-Q100 Compliant
Microprocessor Supervisory Circuit with Manual Reset for Automotive Applications
NO.EC-170-180222
OUTLINE
The R5107G is a microprocessor supervisory circuit and has high accuracy and ultra low supply current voltage
detector with built-in delay circuit and watchdog timer. When the supply voltage is down across the threshold,
or the watchdog timer does not detect the system clock from the microprocessor, the reset output is generated.
The voltage detector circuit is used for the system reset, etc. The detector threshold is fixed internally, and the
accuracy is ±1.0%. The released delay time (Power-on Reset Delay) circuit is built-in, and output delay time is
1)
adjustable with an external capacitor, and the accuracy is ±16% (R5107Gxx1x-TR-JE: −40°C ≤ Ta ≤ 105°C) ( .
When the supply voltage becomes the released voltage, the reset state will be maintained during the delay
time. The output type of the reset is selectable, Nch open-drain, or CMOS.
The time out period of the watchdog timer can be also set with an external capacitor, and the accuracy is
1)
±33%( .
The function to stop supervising clock by the watchdog timer (INH function) and manual reset function are built
in this IC. There are another 4 products by the difference of packages and the function of voltage detector and
watchdog timer. The package of R5107G is SSOP-8G.
FEATURES
• Operating Voltage Range (Maximum Rating)..................0.9V to 6.0V (7.0V)
• Supply Current .................................................................Typ. 11µA
< Voltage Detector Part >
• Detector Threshold Range...............................................1.5V to 5.5V (0.1V steps)
• Detector Threshold Accuracy...........................................±1.0%
• Detector Threshold Temperature Coefficient ...................Typ. ±100 ppm/°C
R5107Gxx1x-TR-AE: −40°C ≤ Ta ≤ 125°C
R5107Gxx1x-TR-JE: −40°C ≤ Ta ≤ 105°C
• Power-on Reset Delay Time accuracy(1)....................... ±18% (R5107Gxx1x-TR-AE: −40°C ≤ Ta ≤ 125°C)
±16% (R5107Gxx1x-TR-JE: −40°C ≤ Ta ≤ 105°C)
• Power-on reset delay time of the voltage detector ..........Typ. 370ms with an external capacitor : 0.1µF
• With Manual Reset pin (MR)............................................Able to reset voltage detector and watchdog
timer
< Watchdog Timer Part >
• Built-in a watchdog timer's time out period accuracy(1)....±33%
R5107Gxx1x-TR-AE: −40°C ≤ Ta ≤ 125°C
R5107Gxx1x-TR-JE: −40°C ≤ Ta ≤ 105°C
• Timeout period for watchdog timer ..................................Typ. 310ms with an external capacitor : 0.1µF
• Reset timer for watchdog timer........................................Typ. 34ms with an external capacitor : 0.1µF
• With Inhibit pin (INH)........................................................Able to stop watchdog timer
• Package ...........................................................................SSOP-8G
APPLICATIONS
• Voltage monitoring for electronic control units such as EV inverter and battery charge control unit.
1
R5107G
NO.EC-170-180222
SELECTION GUIDE
The detector threshold, the output type and the taping type for the ICs can be selected at the users’ request.
The selection can be made with designating the part number as shown below;
Product Name
Package
Quantity per Reel
Pb Free
Halogen Free
SSOP-8G
3,000 pcs
Yes
Yes
R5107Gxx1∗-TR-#E
xx: The detector threshold (-VDET) can be designated in the range from 1.5V(15) to 5.5V(55) in 0.1V steps.
∗ : Designation of Output Type
(A) Nch Open Drain
(C) CMOS
# : Quality Class
Operating Temperature Range
−40°C to 125°C
Test Temp.
25°C, High
AEC-Q100
Grade 1
A
J
−40°C to 105°C
Low, 25°C, High
Grade 2
Series Selection
R5105N
R5106N
R5107G
R5108G
R5109G
Package
SOT-23-6
SSOP-8G
With INH pin (Inhibit)
No
Yes
2 clock input
No
Yes
No
With MR pin (Manual
Reset)
No
Yes
No
With SENSE pin
No
Yes
CD pin and
CTW pin are
combined uses.
Operating
Voltage Range
1.5V to 6.0V
Supply Current
Remarks
11.5µA
2
R5107G
NO.EC-170-180222
BLOCK DIAGRAMS
R5107Gxx1A
R5107Gxx1C
(Nch Open Drain Output)
(CMOS Output)
MR
MR
VDD
VDD
C
D
C
D
Vref2
Vref1
Vref2
Vref1
GND
GND
SCK
C
TW
C
TW
WATCHDOG
TIMER
CLOCK
DETECTOR
WATCHDOG
TIMER
CLOCK
DETECTOR
SCK
RESETB
INH
INH
RESETB
PIN DESCRIPTIONS
• SSOP-8G
8 7 6
5
1 2 3 4
Pin No.
Symbol
Description
Output Pin for Reset signal of Watchdog timer and Voltage Detector.
(Output "L" at detecting Detector Threshold and Watchdog Timer Reset.)
1
RESETB
2
3
4
5
6
7
8
MR
CD
Manual Reset Pin (Active"L")
External Capacitor Pin for Setting Delay Time of Voltage Detector
Ground Pin
GND
SCK
INH
CTW
VDD
Clock Input Pin from Microprocessor
Inhibit Pin ("L": Inhibit the watchdog timer)
External Capacitor Pin for Setting Reset and Watchdog Timeout Periods
Power supply Pin
3
R5107G
NO.EC-170-180222
ABSOLUTE MAXIMUM RATINGS
(Ta=25°C)
Symbol
VDD
Item
Rating
−0.3 to 7.0
−0.3 to VDD + 0.3
−0.3 to VDD + 0.3
−0.3 to 7.0
−0.3 to 7.0
−0.3 to 7.0
−0.3 to 7.0
20
Unit
Supply Voltage
Output Voltage
V
V
VCD
Voltage of CD Pin
VCTW
VRESETB
VSCK
VINH
Voltage of CTW Pin
Voltage of RESETB Pin
Voltage of SCK Pin
Voltage of INH Pin
Voltage of MR Pin
Current of RESETB Pin
V
V
V
Input Voltage
V
VMR
V
IRESETB
PD
Output Current
mA
mW
°C
°C
Power Dissipation(1) (SSOP-8G, Standard Test Land Pattern)
475
Tj
Junction Temperature
−40 to 150
−55 to 150
Tstg
Storage Temperature Range
ABSOLUTE MAXIMUM RATINGS
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent
damages and may degrade the life time and safety for both device and system using the device in the field.
The functional operation at or over these absolute maximum ratings are not assured.
RECOMMENDED OPERATING CONDITIONS
Symbol
Item
Rating
Unit
VDD
Operating Voltage
0.9 to 6.0
V
R5107Gxx1x-TR-AE
R5107Gxx1x-TR-JE
−40 to 125
−40 to 105
°C
°C
Ta
Operating Temperature Range
RECOMMENDED OPERATING CONDITIONS
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the recommended
operating conditions, even if when they are used over such ratings by momentary electronic noise or surge. And the
semiconductor devices may receive serious damage when they continue to operate over the recommended
operating conditions.
(1) Refer to POWER DISSIPATION for detailed information.
4
R5107G
NO.EC-170-180222
ELECTRICAL CHARACTERISTICS
VDD=6.0V, CTW=0.1µF, CD=0.1µF, In case of Nch Open Drain Output type, the output pin is pulled up with a
resistance of 100kΩ (R5107Gxx1A), unless otherwise noted.
The specification in
is checked and guaranteed by design engineering at −40°C ≤ Ta ≤ 125°C.
R5107Gxx1A/C-TR-AE
(Ta=25°C)
Symbol
Item
Conditions
VDD= -VDET+0.5V,
Clock pulse input
Min.
Typ.
Max.
Unit
ISS
Supply Current
11
15
µA
VD Part
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
Ta=25°C
×0.990
×1.010
-VDET Detector Threshold
V
−40°C ≤ Ta ≤ 125°C
×0.972
×1.015
-VDET
-VDET
-VDET
V
V
HYS
Detector Threshold Hysteresis
Output Delay Time
×0.03
×0.05
×0.07
CD=0.1µF (1)
tPLH
340
370
485
ms
Nch
Pch (2)
0.36
0.63
0.8
0.9
mA
mA
VDD=1.2V, VDS=0.1V
VDD=6.0V, VDS=0.5V
Output Current
(RESETB Output pin)
IRESETB
VMRH
VMRL
tMRW
RMR
MR Input "H" (3)
1.0
0
6.0
V
V
MR Input "L"
0.35
MR Input Pulse Width (4)
MR Pull-up Resistance
3
µs
kΩ
60
110
164
WDT Part
Symbol
Item
Conditions
Min.
230
29
Typ.
310
34
Max.
450
Unit
ms
ms
V
tWD
tWR
Watchdog Timeout period
Reset Hold Time of WDT
CTW=0.1µF (1)
CTW=0.1µF (1)
48
VSCKH SCK Input "H"
VSCKL SCK Input "L"
6.0
VDD×0.8
0
VDD×0.2
6.0
V
VINHH
VINHL
RINH
INH Input "H"
V
1.0
INH Input "L"
0.35
164
V
0
INH pull-up Resistance
SCK Input Pulse Width
110
kΩ
ns
60
tSCKW
VSCKL=VDD×0.2,VSCKH=VDD×0.8
500
On all of unit, all items except MR Input Pulse Width in the above are tested and specified under load conditions such that
Tj≈Ta=25°C.
(1) The specification does not contain the temperature characteristics of the external capacitor.
(2) In case of CMOS type (R5107Gxx1C)
(3) In case of CMOS type (R5107Gxx1C)
(4) MR input pulse width specification guarantee the minimum input pulse width of MR pin for output "L" from RESETB
pin. If the "L" pulse width of MR is short, tPLH may be short. Refer to the timing diagram for details.
5
R5107G
NO.EC-170-180222
VDD=6.0V, CTW=0.1µF, CD=0.1µF, In case of Nch Open Drain Output type, the output pin is pulled up with a
resistance of 100kΩ (R5107Gxx1A), unless otherwise noted.
The specification in
is checked and guaranteed by design engineering at −40°C ≤ Ta ≤ 105°C.
R5107Gxx1A/C-TR-JE
(Ta=25°C)
Symbol
Item
Conditions
VDD= -VDET+0.5V,
Clock pulse input
Min.
Typ.
Max.
Unit
ISS
Supply Current
11
15
µA
VD Part
Symbol
Item
Conditions
Min.
Typ.
Max.
Unit
Ta=25°C
×0.990
×1.010
-VDET Detector Threshold
V
−40°C ≤ Ta ≤ 105°C
×0.972
×1.015
-VDET
-VDET
-VDET
V
V
HYS
Detector Threshold Hysteresis
Output Delay Time
×0.03
×0.05
×0.07
CD=0.1µF (1)
tPLH
340
370
467
ms
Nch
Pch (2)
0.38
0.65
0.8
0.9
mA
mA
VDD=1.2V, VDS=0.1V
VDD=6.0V, VDS=0.5V
Output Current
(RESETB Output pin)
IRESETB
VMRH
VMRL
tMRW
RMR
MR Input "H" (3)
1.0
0
6.0
V
V
MR Input "L"
0.35
MR Input Pulse Width (4)
MR Pull-up Resistance
3
µs
kΩ
60
110
164
WDT Part
Symbol
Item
Conditions
Min.
230
29
Typ.
310
34
Max.
450
Unit
ms
ms
V
tWD
tWR
Watchdog Timeout period
Reset Hold Time of WDT
CTW=0.1µF (1)
CTW=0.1µF (1)
48
VSCKH SCK Input "H"
VSCKL SCK Input "L"
6.0
VDD×0.8
0
VDD×0.2
6.0
V
VINHH
VINHL
RINH
INH Input "H"
V
1.0
INH Input "L"
0.35
152
V
0
INH pull-up Resistance
SCK Input Pulse Width
110
kΩ
ns
64
tSCKW
VSCKL=VDD×0.2,VSCKH=VDD×0.8
500
On all of unit, all items except MR Input Pulse Width in the above are tested and specified under load conditions such that
Tj≈Ta=25°C.
(1) The specification does not contain the temperature characteristics of the external capacitor.
(2) In case of CMOS type (R5107Gxx1C)
(3) In case of CMOS type (R5107Gxx1C)
(4) MR input pulse width specification guarantee the minimum input pulse width of MR pin for output "L" from RESETB
pin. If the "L" pulse width of MR is short, tPLH may be short. Refer to the timing diagram for details.
6
R5107G
NO.EC-170-180222
Product-specific Electrical Characteristics
-VDET
VHYS
-40°C ≤ Ta ≤ 125 °C/
-40°C ≤ Ta ≤ 105 °C
Product Name
Ta = 25°C
Min.
Typ.
Max.
1.515
Min.
Typ.
Max.
Max.
Typ.
Max.
R5107G151x
R5107G161x
R5107G171x
R5107G181x
R5107G191x
R5107G201x
R5107G211x
R5107G221x
R5107G231x
R5107G241x
R5107G251x
R5107G261x
R5107G271x
R5107G281x
R5107G291x
R5107G301x
R5107G311x
R5107G321x
R5107G331x
R5107G341x
R5107G351x
R5107G361x
R5107G371x
R5107G381x
R5107G391x
R5107G401x
R5107G411x
R5107G421x
R5107G431x
R5107G441x
R5107G451x
R5107G461x
R5107G471x
R5107G481x
R5107G491x
R5107G501x
R5107G511x
R5107G521x
R5107G531x
R5107G541x
R5107G551x
1.4580
1.5552
1.6524
1.7496
1.8468
1.9440
2.0412
2.1384
2.2356
2.3328
2.4300
2.5272
2.6244
2.7216
2.8188
2.9160
3.0132
3.1104
3.2076
3.3048
3.4020
3.4992
3.5964
3.6936
3.7908
3.8880
3.9852
4.0824
4.1796
4.2768
4.3740
4.4712
4.5684
4.6656
4.7628
4.8600
4.9572
5.0544
5.1516
5.2488
5.3460
1.5225
1.6240
1.7255
1.8270
1.9285
2.0300
2.1315
2.2330
2.3345
2.4360
2.5375
2.6390
2.7405
2.8420
2.9435
3.0450
3.1465
3.2480
3.3495
3.4510
3.5525
3.6540
3.7555
3.8570
3.9585
4.0600
4.1615
4.2630
4.3645
4.4660
4.5675
4.6690
4.7705
4.8720
4.9735
5.0750
5.1765
5.2780
5.3795
5.4810
5.5825
0.045
0.048
0.051
0.054
0.057
0.060
0.063
0.066
0.069
0.072
0.075
0.078
0.081
0.084
0.087
0.090
0.093
0.096
0.099
0.102
0.105
0.108
0.111
0.114
0.117
0.120
0.123
0.126
0.129
0.132
0.135
0.138
0.141
0.144
0.147
0.150
0.153
0.156
0.159
0.162
0.165
0.105
0.112
0.119
0.126
0.133
0.140
0.147
0.154
0.161
0.168
0.175
0.182
0.189
0.196
0.203
0.210
0.217
0.224
0.231
0.238
0.245
0.252
0.259
0.266
0.273
0.280
0.287
0.294
0.301
0.308
0.315
0.322
0.329
0.336
0.343
0.350
0.357
0.364
0.371
0.378
0.385
1.485
1.584
1.683
1.782
1.881
1.980
2.079
2.178
2.277
2.376
2.475
2.574
2.673
2.772
2.871
2.970
3.069
3.168
3.267
3.366
3.465
3.564
3.663
3.762
3.861
3.960
4.059
4.158
4.257
4.356
4.455
4.554
4.653
4.752
4.851
4.950
5.049
5.148
5.247
5.346
5.445
1.500
1.600
1.700
1.800
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.000
3.100
3.200
3.300
3.400
3.500
3.600
3.700
3.800
3.900
4.000
4.100
4.200
4.300
4.400
4.500
4.600
4.700
4.800
4.900
5.000
5.100
5.200
5.300
5.400
5.500
1.500
0.075
0.080
0.085
0.090
0.095
0.100
0.105
0.110
0.115
0.120
0.125
0.130
0.135
0.140
0.145
0.150
0.155
0.160
0.165
0.170
0.175
0.180
0.185
0.190
0.195
0.200
0.205
0.210
0.215
0.220
0.225
0.230
0.235
0.240
0.245
0.250
0.255
0.260
0.265
0.270
0.275
1.616
1.717
1.818
1.919
2.020
2.121
2.222
2.323
2.424
2.525
2.626
2.727
2.828
2.929
3.030
3.131
3.232
3.333
3.434
3.535
3.636
3.737
3.838
3.939
4.040
4.141
4.242
4.343
4.444
4.545
4.646
4.747
4.848
4.949
5.050
5.151
5.252
5.353
5.454
5.555
1.600
1.700
1.800
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.000
3.100
3.200
3.300
3.400
3.500
3.600
3.700
3.800
3.900
4.000
4.100
4.200
4.300
4.400
4.500
4.600
4.700
4.800
4.900
5.000
5.100
5.200
5.300
5.400
5.500
7
R5107G
NO.EC-170-180222
THEORY OF OPERATION
TIMING CHART
+VDET
VDD
-VDET
VDDL
VINH
VMR
t
PHL
t
PHL
t
PLH
t
PLH
+VTCD
-VTCD
V
CD
tWDI
tWD
tWD
Vref2H
VCTW
Vref2L
tWR
tWR
VSCK
t
MR
t
PLH
VRESETB
Undefined
Undefined
(1) (2)
(4)
(3)(5)
(6)
(7)
(8)
(9)
∗) VTCD : Threshold voltage of CD pin when a power-on reset pulse inverting.
∗) Vref2H : CTW pin voltage at the end of WDT timeout period.
∗) Vref2L : CTW pin voltage at the begin of WDT timeout period.
8
R5107G
NO.EC-170-180222
Operating Description
(1) When the power supply, VDD pin voltage becomes more than the released voltage (+VDET), after the released
delay time (or the power on reset time tPLH), the output of RESETB becomes "H" level.
(2) When the SCK pulse is input, the watchdog timer is cleared, and CTW pin mode changes from the discharge
mode to the charge mode. When the CTW pin voltage becomes higher than Vref2H, the mode will change into
the discharge mode, and next watchdog time count starts.
(3) Unless the SCK pulse is input, WDT will not be cleared, and during the charging period of CTW pin,
RESETB="L".
(4) When the VDD pin becomes lower than the detector threshold voltage (-VDET), RESETB outputs "L" after the
tPHL.
(5) If "L" signal is input to the INH pin, the RESETB outputs "H", regardless the SCK clock state.
(6) During the "L" period of INH pin, the voltage detector monitors the supply voltage.
(7) When the signal to the INH pin is set from "L" to "H", the watchdog starts supervising the system clock, or
charge cycle to the CTW pin starts, the capacitor connected to the CTW pin is charged with the current of
setting Reset time of WDT.
(8) If "L" signal is input to the MR pin, the RESETB outputs "L" after the tMR, regardless the SCK clock state
and VDD voltage.
(9) When the signal to the MR pin is set from "L" to "H", the RESETB outputs "H" after the tPLH, the watchdog
starts supervising the system clock.
Watchdog Timeout period/Reset hold time
The watchdog timeout period and reset hold time can be set with an external capacitor to CTW pin.
The next equations describe the relation between the watchdog timeout period and the external capacitor
value, or the reset hold time and the external capacitor value.
tWD (s) = 3.1 × 106 × C (F)
tWR (s)= tWD/9
The watchdog timer (WDT) timeout period is determined with the discharge time of the external capacitor.
During the watchdog timeout period, if the clock pulse from the system is detected, WDT is cleared and the
capacitor is charged. When the charge of the capacitor completes, another watchdog timeout period starts
again. During the watchdog timeout period, if the clock pulse from the system is not detected, during the next
reset hold time RESETB pin outputs "L".
During the reset time, (while charging the external capacitor) and after starting the watchdog timeout period,
(just after from the discharge of the external capacitor) even if the clock pulse is input during the time period
"tWDI", the clock pulse is ignored.
tWDI (s) = tWD/10
9
R5107G
NO.EC-170-180222
Released Delay Time (Power-on Reset delay time)
The released delay time can be set with an external capacitor connected to the CD pin. The next equation
describes the relation between the capacitance value and the released delay time (tPLH).
tPLH (s) =3.7 × 106 × C (F)
The capacitor connected to CD pin determines tWD, tWR, and tPLH.
When the VDD voltage becomes equal or less than (-VDET), discharge of the capacitor connected to the CD pin
starts. Therefore, if the discharge is not enough and VDD voltage returns to (+VDET) or more, thereafter the delay
time will be shorter than tPLH which is expected.
Power on Reset Operation against the input glitch (tPLH1 < tPLH)
+VDET
-VDET
VDD
0V
Complete
Discharge
+VTCD
-VTCD
VCD
0V
Incomplete
Discharge
VRESETB
0V
t
PLH1
t
PLH
Minimum Operating Voltage
We specified the minimum operating voltage as the minimum input voltage in which the condition of RESETB
pin being 0.1V or lower than 0.1V. (Herein, pull-up resistance is set as 100kΩ in the case of the Nch open-
drain output type.)
10
R5107G
NO.EC-170-180222
Manual Reset (MR) Function
By setting MR pin as "L", the output of RESETB can be forced to set "L". After pull-down the MR pin to "L", the
delay time (tMR) to the output "L" from RESETB is 1µs as maximum. MR pin is pulled-up via the built-in resistor.
(Typ. 110kΩ ). If MR pin voltage > VDD voltage, a current flows into MR pin. However, the current value is limit
by the pull-up resistor, therefore there is not bad impact on the operation. When the "L" signal is input to MR
pin, the discharge of CD pin capacitor (CD) starts. If the term of "L" for MR pin is short, CD will not be discharged
enough. As a result, the delay time after setting "H" for MR pin will be shorter than expected. Because of this,
confirm the operation under the same conditions as users' applications. For example, in case of CD is set at
0.1µF, and the condition to maintain the delay time value after MR pin's returning to "H", is described as the
minimum "L" term of MR pin, or 150µs. When MR input pulse (tMRW) is less than 3.0µs, output delay time (tPLH)
might not exist.
Power on Reset Operation with MR pin input (tPLH1 < tPLH, tMRW1 < tMRW)
VMR
0V
Incomplete
Discharge
Complete
Discharge
+VTCD
-VTCD
VCD
0V
t
MR
t
MR
t
MR
VRESETB
0V
t
MRW1
t
MRW1
t
PLH1
t
MRW
t
PLH
Inhibit (INH) Function
If INH pin is set at "L", the watchdog timer stops monitoring the clock, and the RESETB output will be dominant
by the voltage detector's operation. Therefore, if the supply voltage is set at more than the detector threshold
level, RESETB outputs "H" regardless the clock pulse. INH pin is pulled up with a resistor (Typ.110kΩ) internally.
RESETB Output
RESETB pin's output type is selectable either the Nch open-drain output or CMOS output. If the Nch open-
drain type output is selected, the RESETB pin is pulled up with an external resistor to an appropriate voltage
source.
Clock Pulse Input
Built-in watchdog timer is cleared with the SCK clock pulse within the watchdog timeout period.
11
R5107G
NO.EC-170-180222
APPLICATION INFORMATION
Typical Application Circuits
Power Supply
Microprocessor
VDD
R
8
6
2
3
RESETB
R5107Gxx1A
1
5
V
DD
RESET
I/O
INH
MR
SCK
SW SW
C
D
CTW
7
GND
4
C
TW
C
D
R5107Gxx1A
Power Supply
Microprocessor
VDD
8
6
2
3
RESETB
R5107Gxx1C
1
5
V
DD
RESET
I/O
INH
MR
SCK
SW SW
C
D
CTW
7
GND
4
C
TW
C
D
R5107Gxx1C
12
R5107G
NO.EC-170-180222
TECHNICAL NOTES
When connecting resistors to the device’s input pin
When connecting a resistor (R1) to an input of this device, the input voltage decreases by [Device’s
Consumption Current] x [Resistance Value] only. And, the cross conduction current(1), which occurs when
changing from the detecting state to the release state, is decreased the input voltage by [Cross Conduction
Current] x [Resistance Value] only. And then, this device will enter the re-detecting state if the input voltage
reduction is larger than the difference between the detector voltage and the released voltage.
When the input resistance value is large and the VDD is gone up at mildly in the vicinity of the released voltage,
repeating the above operation may result in the occurrence of output.
As shown in Figure A/B, set R1 to become 100kΩ or less as a guide, and connect CIN(2) of 0.1μF and more to
between the input pin and GND. Besides, make evaluations including temperature properties under the actual
usage condition, with using the evaluation board like this way. As result, make sure that the cross conduction
current has no problem.
R1
R1
VDD
Voltage
Detector
VDD
Voltage
Detector
(2)
(2)
CIN
CIN
R2
OUT pin
OUT pin
GND
Figure A
GND
Figure B
(1) In the CMOS output type, a charging current for OUT pin is included.
(2) Note the bias dependence of capacitors.
13
R5107G
NO.EC-170-180222
TYPICAL CHARACTERISTICS
Note: Typical Characteristics are intended to be used as reference data; they are not guaranteed.
1) Supply Current vs. Input Voltage
R510xx151x
R510xx301x
20
18
16
14
12
10
8
20
18
16
14
12
10
8
Ta=125℃
Ta=25℃
Ta=-40℃
Ta=125℃
Ta=25℃
Ta=-40℃
6
6
4
4
2
2
0
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
Input Voltage VDD(V)
Input Voltage VDD(V)
2) Detector Threshold vs. Temperature
R510xx151x
R510xx271x
1.53
2.74
2.73
2.72
2.71
2.70
2.69
2.68
2.67
2.66
1.52
1.51
1.50
1.49
1.48
1.47
-40 -25
0
25
50
75
100 125
-40-25
0
25
50
75 100 125
Ta (°C)
Ta (°C)
R510xx421x
4.28
4.26
4.24
4.22
4.20
4.18
4.16
4.14
4.12
-40-25
0
25
50
75 100 125
Ta (°C)
14
R5107G
NO.EC-170-180222
3) Detector Threshold Hysteresis vs. Temperature
R510xx151x
R510xx271x
7
6
5
4
3
7
6
5
4
3
-40 -25
0
25
Ta (°C)
R510xx421x
50
75
100 125
-40 -25
0
25
50
75 100 125
Ta (°C)
7
6
5
4
3
-40 -25
0
25
50
75 100 125
Ta (°C)
4) Nch Driver Output Current vs. VDS
R510xx
DD
DD
DD
DD
DD
DD
DD
15
R5107G
NO.EC-170-180222
5) Nch Driver Output Current vs. Input Voltage
R510xx
R510xx
VDS=0.3V
VDS=0.5V
20
18
16
14
12
10
8
20
18
16
14
12
10
8
Ta=125℃
Ta=125℃
Ta=25℃
Ta=-40℃
Ta=25℃
Ta=-40℃
6
6
4
4
2
2
0
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
Input Voltage VDD (V)
Input Voltage VDD (V)
6) Pch Driver Output Current vs. Input Voltage
R510xx
R510xx
VDS=0.5V
VDS=0.3V
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
Ta=-40℃
Ta=25℃
Ta=125℃
Ta=-40℃
Ta=25℃
Ta=125℃
0
1
2
3
4
5
6
0
1
2
3
4
5
6
Input Voltage VDD (V)
Input Voltage VDD (V)
R510xx
VDS=1.0V
2.0
Ta=-40℃
Ta=25℃
Ta=125℃
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
1
2
3
4
5
6
Input Voltage VDD (V)
16
R5107G
NO.EC-170-180222
7) Released Delay Time vs. Input Voltage
R510xx
8) Released Delay Time vs. Temperature
R510xx
VDD=6V
Ta=25°C
500
500
480
460
440
420
400
380
360
340
320
300
480
460
440
420
400
380
360
340
320
300
-40 -25
0
25
50
75 100 125
0
1
2
3
4
5
6
7
Ta (°C)
Input Voltage VDD [V]
9) Detector Output Delay Time vs. Temperature 10) WDT Reset Timer vs. Temperature
R510xx
R510xx
100
90
80
70
60
50
40
30
20
10
0
50
48
46
44
42
40
38
36
34
32
30
1us
(-VDET)+1
(-VDET)- 1
Input Voltage
-40 -25
0
25
50
75 100 125
-40 -25
0
25
50
75 100 125
Ta (°C)
Ta (°C)
11) WDT Timeout Period vs. Temperature
R510xx
12) WDT Reset Timer vs. Input Voltage
R510xx
400
380
360
340
320
300
280
260
240
220
200
50
48
46
44
42
40
38
36
34
32
30
-40 -25
0
25
50
75 100 125
1
2
3
4
5
6
Input Voltage VDD (V)
Operation Temperature Ta [°C]
17
R5107G
NO.EC-170-180222
13) WDT Timeout Period vs. Input Voltage 14) Output Delay Time vs. External Capacitance
R510xx
R510xx
1000
100
10
400
380
360
340
320
300
280
260
240
220
200
t
PLH
1us
1us
1
(-VDET)+1
(-VDET)-1
Input
0.1
Voltage
0.01
0.001
tPHL
0.1
1
10
100
1
2
3
4
5
6
Input Voltage VDD (V)
External Capacitance C [nF]
D
18
POWER DISSIPATION
SSOP-8G
Ver. A
The power dissipation of the package is dependent on PCB material, layout, and environmental conditions.
The following conditions are used in this measurement.
Measurement Conditions
Standard Test Land Pattern
Environment
Board Material
Mounting on Board (Wind Velocity = 0 m/s)
Glass Cloth Epoxy Plastic (Double-Sided Board)
Board Dimensions
40 mm × 40 mm × 1.6 mm
Top Side: Approx. 50%
Bottom Side: Approx. 50%
φ 0.5 mm × 44 pcs
Copper Ratio
Through-holes
Measurement Result
(Ta = 25°C, Tjmax = 150°C)
Standard Test Land Pattern
475 mW
Power Dissipation
θja = (150 − 25°C) / 0.475 W = 263°C/W
θjc = 60°C/W
Thermal Resistance
40
600
500
400
300
200
100
0
475
105
0
25
50
75
100
125
150
IC Mount Area (mm)
Ambient Temperature (°C)
Power Dissipation vs. Ambient Temperature
Measurement Board Pattern
i
PACKAGE DIMENSIONS
SSOP-8G
Ver. A
2.9±0.2
5
8
1
4
4.0±0.2
2.8±0.2
0.475nom.
0°-15°
0.45±0.15
0.65
0.1
0.2±0.1
0.15
M
SSOP-8G Package Dimensions (Unit: mm)
i
1. The products and the product specifications described in this document are subject to change or discontinuation of
production without notice for reasons such as improvement. Therefore, before deciding to use the products, please
refer to Ricoh sales representatives for the latest information thereon.
2. The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written
consent of Ricoh.
3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise
taking out of your country the products or the technical information described herein.
4. The technical information described in this document shows typical characteristics of and example application circuits
for the products. The release of such information is not to be construed as a warranty of or a grant of license under
Ricoh's or any third party's intellectual property rights or any other rights.
5. The products in this document are designed for automotive applications. However, when using the products for
automotive applications, please make sure to contact Ricoh sales representative in advance due to confirming the
quality level.
6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products
are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from
such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy
feature, fire containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or
damage arising from misuse or inappropriate use of the products.
7. Anti-radiation design is not implemented in the products described in this document.
8. The X-ray exposure can influence functions and characteristics of the products. Confirm the product functions and
characteristics in the evaluation stage.
9. WLCSP products should be used in light shielded environments. The light exposure can influence functions and
characteristics of the products under operation or storage.
10. There can be variation in the marking when different AOI (Automated Optical Inspection) equipment is used.
In the case of recognizing the marking characteristic with AOI, please contact Ricoh sales or our distributor before
attempting to use AOI.
11. Please contact Ricoh sales representatives should you have any questions or comments concerning the products or
the technical information.
Ricoh is committed to reducing the environmental loading materials in electrical devices
with a view to contributing to the protection of human health and the environment.
Ricoh has been providing RoHS compliant products since April 1, 2006 and Halogen-free products since
Halogen Free
April 1, 2012.
https://www.e-devices.ricoh.co.jp/en/
Sales & Support Offices
Ricoh Electronic Devices Co., Ltd.
Shin-Yokohama Office (International Sales)
2-3, Shin-Yokohama 3-chome, Kohoku-ku, Yokohama-shi, Kanagawa, 222-8530, Japan
Phone: +81-50-3814-7687 Fax: +81-45-474-0074
Ricoh Americas Holdings, Inc.
675 Campbell Technology Parkway, Suite 200 Campbell, CA 95008, U.S.A.
Phone: +1-408-610-3105
Ricoh Europe (Netherlands) B.V.
Semiconductor Support Centre
Prof. W.H. Keesomlaan 1, 1183 DJ Amstelveen, The Netherlands
Phone: +31-20-5474-309
Ricoh International B.V. - German Branch
Semiconductor Sales and Support Centre
Oberrather Strasse 6, 40472 Düsseldorf, Germany
Phone: +49-211-6546-0
Ricoh Electronic Devices Korea Co., Ltd.
3F, Haesung Bldg, 504, Teheran-ro, Gangnam-gu, Seoul, 135-725, Korea
Phone: +82-2-2135-5700 Fax: +82-2-2051-5713
Ricoh Electronic Devices Shanghai Co., Ltd.
Room 403, No.2 Building, No.690 Bibo Road, Pu Dong New District, Shanghai 201203,
People's Republic of China
Phone: +86-21-5027-3200 Fax: +86-21-5027-3299
Ricoh Electronic Devices Shanghai Co., Ltd.
Shenzhen Branch
1205, Block D(Jinlong Building), Kingkey 100, Hongbao Road, Luohu District,
Shenzhen, China
Phone: +86-755-8348-7600 Ext 225
Ricoh Electronic Devices Co., Ltd.
Taipei office
Room 109, 10F-1, No.51, Hengyang Rd., Taipei City, Taiwan
Phone: +886-2-2313-1621/1622 Fax: +886-2-2313-1623
相关型号:
R5107G341A-TR
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO8, 2.90 X 4 MM, 0.65 MM PITCH, SSOP-8
RICOH
R5107G341C-TR-F
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO8, ROHS COMPLIANT, SSOP-8
RICOH
R5107G351C-TR
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO8, 2.90 X 4 MM, 0.65 MM PITCH, SSOP-8
RICOH
R5107G371A-TR
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO8, 2.90 X 4 MM, 0.65 MM PITCH, SSOP-8
RICOH
R5107G371A-TR-F
Power Supply Management Circuit, Fixed, 1 Channel, CMOS, PDSO8, ROHS COMPLIANT, SSOP-8
RICOH
©2020 ICPDF网 联系我们和版权申明