PF2203-24KF1 [RIEDON]
RES 24K OHM 35W 1% TO220;
| 型号： | PF2203-24KF1 |
| 厂家： | 
RIEDON POWERTRON |
| 描述： | RES 24K OHM 35W 1% TO220 |
| 文件： | 总3页 (文件大小：339K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PF2200 Series
TO-220 Power Thin Film Resistors
• TO-220 Housing
• Rated Power to 50 Watts
• Resistances from 0.02 to 51K Ohms
• High Stability Film Resistance Elements
• Resistance Tolerance to ±0.1%
• TCR to ±50ppm/°C
• Low Inductance ( <10nH )
• Excellent Pulse Handling
• Isolated Mounting Tab
SPECIFICATIONS
Resistance Range3
Power Rating
Heatsink1 Free Air2
Temperature
Coefficients
Thermal
Resistance
Type
Tolerances4
Min
Max
±50ppm/°C ( R≥10W )
±100ppm/°C ( 0.1W ≤ R < 10W )
±250ppm/°C ( R < 0.1W )
±1% and ±5%
±5% below 0.1W
PF2205
PF2203
PF2202
50W
35W
20W
1W
1W
1W
2.3°C/W
3.3°C/W
5.9°C/W
0.02W
51KW
±50ppm/°C ( R≥10W )
±100ppm/°C ( 0.1W ≤ R < 10W )
±250ppm/°C ( R < 0.1W )
±1% and ±5%
±5% below 0.1W
0.02W
0.02W
51KW
51KW
±50ppm/°C ( R≥10W )
±100ppm/°C ( 0.1W ≤ R < 10W )
±250ppm/°C ( R < 0.1W )
±1% and ±5%
±5% below 0.1W
1 Power rating based on 25°C Flange Temperature
2 Power rating based on 25°C Ambient Temperature
3
Consult Factory for Higher or Lower Values
4 Consult Factory for possible tighter tolerances
Specification
Value
Temperature Range
Dielectric Strength
-55°C to +175°C
2000 VAC
( 500V MAX )
Max. Operating Voltage
Insulation Resistance
P * R
>1000 Meg-Ohm
Tin Plated Copper
Terminal Finish
Inductance
Flammability
Mass
PF2202 / PF2203 8.38 nH, PF2205 9.65 nH
UL94 V-0
2.1g
Ordering Information
Part Description: Part Type - Resistance - Tolerance - TCR
Example: PF2203 0.5 Ohm 1% 100ppm
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
(626) 284-9901
(626) 284-1704
© Riedon, Inc.
www.riedon.com
sales@riedon.com
Revised: 202005_003
PF2200 Series
TO-220 Power Thin Film Resistors
SPECIFICATIONS(continued)
Environmental Performance
Load Life
DR
Test Conditions
±1%
25°C, 90 min ON, 30 min OFF, 1000 hr
40°C, 90-95% RH, DC 0.1W, 1000 hr
-55°C for 30 min, +155°C for 30 min, 5 cycles
+350 / -5°C 3s
Humidity Resistance
Temperature Cycle
Solder Heat
±1%
±0.25%
±0.1%
±0.25%
IEC60068-2-6
Vibration
Power Rating Notes -
Power Derating
% Power
The PF2200 Series Thin Film Resistors must be attached to a
suitable heatsink. Without a heatsink the maximum power rating
is 1W ( 1/2W for the PF2201 ). The maximum internal resistor
temperature is 175°C.
+25 °C
100
80
60
40
20
0
To specify an appropriate heatsink use the following formula :
TMAX - (P * RHR) - T
RHH =
P
+175 °C
150
Where: RqH = Thermal Resistance of Heatsink ( °C/W )
RqR = Thermal Resistance of Resistor ( °C/W )
TMAX = Maximum Temperature of Resistor ( °C )
TA = Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
-50
0
50
100
200
Flange Temperature (C)
C
A
tol.
(±mm)
tol.
G
N
D
Dimension
mm
10.1
15.0
4.5
inches (±inches)
A
B
C
D
E
F
0.2
0.2
0.40
0.60
0.18
0.14
0.61
0.16
0.12
0.11
0.02
0.03
0.06
0.20
0.06
0.63
0.008
0.008
0.008
0.004
0.04
0.2
B
3.6
0.1
P
15.5
4.0
1.0
0.5
0.02
G
H
J
3.0
0.2
0.008
0.008
0.002
0.002
0.002
0.004
0.002
0.02
L
2.75
0.5
0.2
H
F
0.05
0.05
0.05
0.1
E
K
L
0.75
1.5
K
J
M
N
P
5.08
1.5
0.05
0.50
M
16.0
Mounting Notes -
The PF2200 Series Thin Film Resistors must be attached to a suitable heatsink. Mount resistor using thermal grease to a clean, flat surface. Use
a compression washer to provide 150 to 300 pounds ( 665 to 1330N ) of mounting force. Torque mounting screw to 8 in-lbs ( 0.9 N-m ).
Mounting tab is isolated from both pins.
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
(626) 284-9901
(626) 284-1704
© Riedon, Inc.
www.riedon.com
sales@riedon.com
Revised: 202005_003
PF2200 Series
TO-220 Power Thin Film Resistors
PULSE ENERGY DURABILITY
Pulse Energy Durability
Pulse Peak Power (W)
1000k
Pulse Energy Durability
Pulse Peak Power (W)
PF2203_10ohm-1%
PF2202_10ohm-1%
1000k
Tentative continuous-pulse power allowance at
duty 0.01. Load life test will be necessary in
actual equipment, Because curve will be changed
by resistance, repetition, duty and operating
temperature. Dotted shows estimation.
Tentative continuous-pulse power allowance at
duty 0.01. Load life test will be necessary in
actual equipment, Because curve will be changed
by resistance, repetition, duty and operating
temperature. Dotted shows estimation.
100k
10k
100k
10k
1k
1k
400W
100
100
200W
20W
35W
10
10
10n 100n 1u 10u 100u 1m 10m 100m
1
10
10n 100n 1u 10u 100u 1m 10m 100m
1
10
Pulse Energy Durability
Pulse Peak Power (W)
PF2205_10ohm-1%
1000k
Tentative continuous-pulse power allowance at
duty 0.01. Load life test will be necessary in
actual equipment, Because curve will be changed
by resistance, repetition, duty and operating
temperature. Dotted shows estimation.
100k
10k
1k
400W
100
10
50W
10n 100n 1u 10u 100u 1m 10m 100m
1
10
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
(626) 284-9901
(626) 284-1704
© Riedon, Inc.
www.riedon.com
sales@riedon.com
Revised: 202005_003
相关型号：
©2020 ICPDF网 联系我们和版权申明