AD9214BRS-RL65 [ROCHESTER]
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28;型号: | AD9214BRS-RL65 |
厂家: | Rochester Electronics |
描述: | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28 光电二极管 |
文件: | 总21页 (文件大小:1129K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
10-Bit, 65/80/105 MSPS
3 V A/D Converter
a
AD9214
FEATURES
FUNCTIONAL BLOCK DIAGRAM
SNR = 57 dB @ 39 MHz Analog Input (–0.5 dBFS)
Low Power
AV
PWRDWN
DrV
DD
DD
190 mW at 65 MSPS
285 mW at 105 MSPS
AD9214
DFS/GAIN
OR
30 mW Power-Down Mode
300 MHz Analog Bandwidth
On-Chip Reference and Track/Hold
1 V p-p or 2 V p-p Analog Input Range Option
Single 3.3 V Supply Operation (2.7 V–3.6 V)
Two’s Complement or Offset Binary Data Format Option
A
A
10
PIPELINE
IN
BUFFER
T/H
ADC
CORE
IN
10
D –D
9
0
ENCODE
TIMING
AGND
REF
APPLICATIONS
Battery-Powered Instruments
Hand-Held Scopemeters
Low-Cost Digital Oscilloscopes
Ultrasound Equipment
Cable Reverse Path
REF REFSENSE
DGND
Broadband Wireless
Residential Power Line Networks
PRODUCT DESCRIPTION
PRODUCT HIGHLIGHTS
The AD9214 is a 10-bit monolithic sampling analog-to-digital
converter (ADC) with an on-chip track-and-hold circuit, and
is optimized for low cost, low power, small size, and ease of use.
The product operates up to 105 MSPS conversion rate with
outstanding dynamic performance over its full operating range.
High Performance—Outstanding ac performance from 65 MSPS
to 105 MSPS. SNR greater than 55 dB typical and as high
as 58 dB.
Low Power—The AD9214 at 285 mW consumes a fraction of
the power available in existing high-speed monolithic solutions.
In sleep mode, power is reduced to 30 mW.
The ADC requires only a single 3.3 V (2.7 V to 3.6 V) power
supply and an encode clock for full performance operation. No
external reference or driver components are required for many
applications. The digital outputs are TTL/CMOS compatible
and a separate output power supply pin supports interfacing
with 3.3 V or 2.5 V logic.
Single Supply—The AD9214 uses a single 3 V supply, simplify-
ing system power supply design. It also features a separate digital
output driver supply line to accommodate 2.5 V logic families.
Small Package—The AD9214 is packaged in a small 28-lead
surface-mount plastic package (28-SSOP).
The clock input is TTL/CMOS compatible. In the power-down
state, the power is reduced to 30 mW. A gain option allows
support for either 1 V p-p or 2 V p-p analog signal input swing.
Fabricated on an advanced CMOS process, the AD9214 is
available in a 28-lead surface-mount plastic package (28-SSOP)
specified over the industrial temperature range (–40°C to +85°C).
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© Analog Devices, Inc., 2002
AD9214–SPECIFICATIONS
(AVDD = 3 V, DrVDD = 3 V; TMIN = –40؇C, TMAX = +85؇C; external 1.25 V voltage reference and rated encode
frequency used, unless otherwise noted.)
DC SPECIFICATIONS
Test
Level
AD9214-65
Typ
AD9214-80
Typ
AD9214-105
Typ
Parameter
Temp
Min
Max
Min
Max
Min
Max
Unit
RESOLUTION
10
10
10
Bits
ACCURACY
No Missing Codes
25°C
Full
Full
25°C
25°C
Full
25°C
Full
VI
VI
VI
I
I
V
I
Guaranteed
Guaranteed
0
Guaranteed
Guaranteed
0
Guaranteed
Offset Error
–18
–2
+18
+8
+1.0
+1.2
+1.35
+1.9
–18
–2
–1.0
–1.0
–1.5
–1.8
+18
+8
+1.2
+1.4
–18
–2
–1.0
0
+18
+8
+1.5
+1.7
+2.2
+2.5
LSB
% FS
LSB
LSB
LSB
LSB
Gain Error1
Differential Nonlinearity2
(DNL)
–1.0
–1.0
–1.35
–1.9
0.5
0.5
0.8
1.5
Integral Nonlinearity2
(INL)
0.75
0.75 +1.5
+1.8
–2.2
–2.5
V
TEMPERATURE DRIFT
Offset Error
Full
Full
Full
V
V
V
16
150
80
16
150
80
16
150
80
ppm/°C
ppm/°C
ppm/°C
Gain Error1
Reference Voltage
REFERENCE (REF)
Internal Reference Voltage
Output Current3
25°C
Full
Full
Full
VI
V
V
1.18
1.23
200
123
10
1.28
1.18
1.23
200
123
10
1.28
1.18
1.23
200
123
10
1.28
V
µA
µA
kΩ
Input Current4
Input Resistance
V
ANALOG INPUTS (AIN, AIN)
Differential Input Range
Full
Full
Full
Full
V
V
V
V
1 or 2
AVDD/3
20
1 or 2
AVDD/3
20
1 or 2
AVDD/3
20
V p-p
V
kΩ
pF
Common-Mode Voltage
Differential Input Resistance5
Differential Input Capacitance
5
5
5
POWER SUPPLY
Supply Voltages
AVDD
Full
Full
IV
IV
2.7
2.7
3.6
3.6
2.7
2.7
3.6
3.6
2.7
2.7
3.6
3.6
V
V
DrVDD
Supply Current
IAVDD (AVDD = 3.0 V)6
Power-Down Current7
IAVDD (AVDD = 3.0 V)
Power Consumption8
PSRR
Full
VI
64
75
90
105
95
110
mA
Full
Full
25°C
Full
VI
VI
I
10
190
0.5
2
15
220
10
250
1
15
300
10
285
1
15
325
mA
mW
LSB/V
mV/V
V
2
2
NOTES
1Gain error and gain temperature coefficient are based on the ADC only (with a fixed 1.25 V external reference).
2Measured with 1 V AIN range for AD9214-80 and AD9214-105. Measured with 2 V AIN range for AD9214-65.
3REFSENSE externally connected to AGND, REF is configured as an output for the internal reference voltage.
4REFSENSE externally connected to AVDD, REF is configured as an input for an external reference voltage.
510 kΩ to AVDD/3 on each input.
6IAVDD is measured with an analog input of 10.3 MHz, 0.5 dBFS, sine wave, rated encode rate, and PWRDN = 0. See Typical Performance Characteristics and
Applications section for IDrVDD
.
7Power-down supply currents measured with PWRDN = 1; rated encode rate, AIN = full-scale dc input.
8Power consumption measured with AIN = full-scale dc input.
Specifications subject to change without notice.
–2–
REV. D
AD9214
DIGITAL SPECIFICATIONS (AVDD = 3 V, DrVDD = 3 V; TMIN = –40؇C, TMAX = +85؇C)
Test
AD9214-65
Typ
AD9214-80
Typ
AD9214-105
Typ
Parameter
Temp
Level
Min
Max
Min
Max
Min
Max
Unit
DIGITAL INPUTS1
Logic “1” Voltage
Logic “0” Voltage
Input Capacitance
Full
Full
Full
IV
IV
V
2.0
2.0
2.0
V
V
pF
0.8
0.8
0.8
50
2.0
2.0
2.0
DIGITAL OUTPUTS2
Logic Compatibility
Logic “1” Voltage
CMOS/TTL
CMOS/TTL
CMOS/TTL
V
V
mV
Full
Full
VI
VI
DrVDD – 50 mV
DrVDD – 50 mV
DrVDD – 50 mV
Logic “0” Voltage
50
50
NOTES
1Digital Inputs include ENCODE and PWRDN.
2Digital Outputs include D0–D9 and OR.
Specifications subject to change without notice.
(AVDD = 3 V, DrVDD = 3 V; ENCODE = Maximum Conversion Rate; TMIN = –40؇C, TMAX = +85؇C; external
AC SPECIFICATIONS1 1.25 V voltage reference used, unless otherwise noted.)
Test
Level
AD9214-65
Typ
AD9214-80
Typ
AD9214-105
Typ
Parameter
Temp
Min
Max
Min
Max
Min
Max
Unit
SNR
Analog Input
@ –0.5 dBFS 39 MHz
51 MHz
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
55.5
58.3
57.1
56.0
55.0
58.1
57.1
55.0
54.0
51.0
50.5
53.0
53.0
53.0
52.6
dB
dB
dB
dB
70 MHz
SINAD
Analog Input
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
55.0
8.9
57.8
56.7
55.5
54.5
57.6
56.7
54.5
50.0
50.0
52.0
52.0
52.0
52.0
dB
dB
dB
dB
@ –0.5 dBFS 39 MHz
51 MHz
70 MHz
EFFECTIVE NUMBER OF BITS
Analog Input
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
9.3
9.2
9.0
8.8
9.3
9.2
8.8
8.5
8.4
8.4
8.4
8.4
Bit
Bit
Bit
Bit
@ –0.5 dBFS 39 MHz
51 MHz
70 MHz
SECOND HARMONIC DISTORTION
Analog Input
@ –0.5 dBFS 39 MHz
51 MHz
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
–66
–79
–75
–64
–63
–74
–76
–72
–65
–62
–62
–68
–71
–64
–62
dBc
dBc
dBc
dBc
70 MHz
THIRD HARMONIC DISTORTION
Analog Input
@ –0.5 dBFS 39 MHz
51 MHz
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
–63.5
63.5
–71
–70
–63
–63
–72
–74
–78
–59
–59
–64
–67
–71
–65
dBc
dBc
dBc
dBc
70 MHz
SFDR
Analog Input
10 MHz
25°C
25°C
25°C
25°C
I
I
V
V
71
70
63
63
71
71
67
64
57
57
62
62
62
62
dBc
dBc
dBc
dBc
@ –0.5 dBFS 39 MHz
51 MHz
70 MHz
TWO-TONE INTERMOD DISTORTION2
Analog Input
@ –0.5 dBFS
25°C
25°C
V
V
76
74
72
dBFS
MHz
ANALOG INPUT BANDWIDTH
NOTES
300
300
300
1AC specifications based on a 1.0 V p-p full-scale input range for the AD9214-80 and AD9214-105, and a 2.0 V p-p full-scale input range for the AD9214-65. An
external reference is used.
2F1 = 29.3 MHz, F2 = 30.3 MHz.
Specifications subject to change without notice.
–3–
REV. D
AD9214–SPECIFICATIONS
(AVDD = 3 V, DrVDD = 3 V; ENCODE = Maximum Conversion Rate; TMIN = –40؇C, TMAX = +85؇C;
SWITCHING SPECIFICATIONS external 1.25 V voltage reference used, unless otherwise noted.)
Test
AD9214-65
Typ
AD9214-80
Typ
AD9214-105
Typ
Parameter
Temp
Level
Min
Max
Min
Max
Min
Max Unit
ENCODE INPUT PARAMETERS*
Maximum Conversion Rate
Minimum Conversion Rate
Full
Full
Full
Full
25°C
25°C
VI
IV
IV
IV
V
65
80
105
MSPS
MSPS
ns
ns
ns
20
20
20
Encode Pulsewidth High (tEH
)
6.0
6.0
5.0
5.0
3.8
3.8
Encode Pulsewidth Low (tEL
Aperture Delay (tA)
)
2.0
3
2.0
3
2.0
3
Aperture Uncertainty (Jitter)
V
ps rms
DATA OUTPUT PARAMETERS
Pipeline Delays
Output Valid Time (tV)*
Full
Full
Full
IV
V
V
5
4.5
4.5
5
4.5
4.5
5
4.5
4.5
Clock Cycle
ns
ns
3.0
3.0
3.0
Output Propagation Delay* (tPD
TRANSIENT RESPONSE TIME
OUT-OF-RANGE RECOVERY TIME
)
6.0
6.0
6.0
25°C
25°C
V
V
5
5
5
5
5
5
ns
ns
*
tV and tPD are measured from the 1.5 V level of the ENCODE input to the 50% levels of the digital output swing. The digital output load during test is not to exceed
an ac load of 5 pF or a dc current of 40 µA.
Specifications subject to change without notice.
SAMPLE N+5
SAMPLE N
SAMPLE N+1
A
IN
tA
SAMPLE N+2
SAMPLE N+4
SAMPLE N+3
ENCODE
1/F
S
tEH
tEL
tPD
tV
D9 – D0
DATA N–5
DATA N–4
DATA N–3
DATA N–2
DATA N–1
DATA N
Figure 1. Timing Diagram
–4–
REV. D
AD9214
ABSOLUTE MAXIMUM RATINGS1
Electrical
EXPLANATION OF TEST LEVELS
I 100% production tested.
AVDD Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 V max
DrVDD Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 V max
Analog Input Voltage . . . . . . . . . . . –0.5 V to AVDD + 0.5 V
Analog Input Current . . . . . . . . . . . . . . . . . . . . . . . 0.4 mA
Digital Input Voltage . . . . . . . . . . . –0.5 V to AVDD + 0.5 V
Digital Output Current . . . . . . . . . . . . . . . . . . 20 mA max
REF Input Voltage . . . . . . . . . . . . . –0.5 V to AVDD + 0.5 V
Environmental2
II 100% production tested at 25°C and guaranteed by design
and characterization at specified temperatures.
III Sample Tested Only
IV Parameter is guaranteed by design and characterization
testing.
V
Parameter is a typical value only.
VI 100% production tested at 25°C and guaranteed by design
Operating Temperature Range (Ambient)
and characterization for industrial temperature range.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +125°C
Maximum Junction Temperature . . . . . . . . . . . . . . . 150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . 150°C
Storage Temperature Range (Ambient) . . . –65°C to +150°C
NOTES
1Absolute maximum ratings are limiting values to be applied individually, and
beyond which the serviceability of the circuit may be impaired. Functional
operability is not necessarily implied. Exposure to absolute maximum rating condi-
tions for an extended period of time may affect device reliability.
2Typical thermal impedances (package = 28 SSOP); θJA = 49°C/W. These
measurements were taken on a 6-layer board in still air with a solid
ground plane.
ORDERING GUIDE
Package Description
Model
Temperature Range
Package Option
AD9214BRS-65
AD9214BRS-80
AD9214BRS-105
AD9214-65PCB
AD9214-105PCB
–40°C to +85°C (Ambient)
–40°C to +85°C (Ambient)
–40°C to +85°C (Ambient)
25°C
28-Lead Shrink Small Outline Package
28-Lead Shrink Small Outline Package
28-Lead Shrink Small Outline Package
Evaluation Board with AD9214-65
Evaluation Board with AD9214-105
RS-28
RS-28
RS-28
25°C
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD9214 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. D
–5–
AD9214
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Function
1
OR
CMOS Output; Out-of-Range Indicator. Logic HIGH indicates the analog input voltage was
outside the converter’s range for the current output data.
2
3
4
DFS/GAIN
REFSENSE
REF
Data Format Select and Gain Mode Select. Connect externally to AVDD for two’s complement
data format and 1 V p-p analog input range. Connect externally to AGND for Offset Binary data
format and 1 V p-p analog input range. Connect externally to REF (Pin 4) for two’s complement
data format and 2 V p-p analog input range. Floating this pin will configure the device for Offset
Binary data format and a 2 V p-p analog input range.
Reference Mode Select Pin for the ADC. This pin is normally connected externally to AGND,
which enables the internal 1.25 V reference, and configures REF (Pin 4) as an analog reference
output pin. Connecting REFSENSE externally to AVDD disables the internal reference, and config-
ures REF (Pin 4) as an external reference input. In this case, the user must drive REF with a clean
and accurate 1.25 V ( 5%) reference input.
Reference input or output as configured by REFSENSE (Pin 3). When configured as an output
(REFSENSE = AGND), the internal reference (nominally 1.25 V) is enabled and is available to
the user on this pin. When configured as an input (REFSENSE = AVDD), the user must drive
REF with a clean and accurate 1.25 V ( 5%) reference. This pin should be bypassed to AGND
with an external 0.1 µF capacitor, whether it is configured as an input or output.
5, 8, 11
6, 7, 12
9
AGND
AVDD
AIN
Analog Ground
Analog Power Supply, Nominally 3 V
Positive terminal of the differential analog input for the ADC.
10
AIN
Negative terminal of the differential analog input for the ADC. This pin can be left open if
operating in single-ended mode, but it is preferable to match the impedance seen at the positive
terminal (see Driving the Analog Inputs).
13
14
ENCODE
PWRDN
Encode Clock for the ADC. The AD9214 samples the analog signal on the rising edge of ENCODE.
CMOS-compatible power-down mode select, Logic LOW for normal operation; Logic HIGH
for power-down mode (digital outputs in high impedance state). PWRDN has an internal
10 kΩ pull-down resistor to ground.
15, 23
16, 24
17–22, 25–28
DGND
DrVDD
D0 (LSB)–D5,
D6–D9 (MSB)
Digital Output Ground
Digital Output Driver Power Supply. Nominally 2.5 V to 3.6 V.
CMOS Digital Outputs of ADC
PIN CONFIGURATION
28-Lead Shrink Small Outline Package
OR
DFS/GAIN
REFSENSE
REF
1
2
28
27
26
25
D9 (MSB)
D8
D7
D6
3
4
5
24 DrV
AGND
DD
6
23
22
AV
DD
DGND
AD9214
TOP VIEW
(Not to Scale)
7
AV
DD
D5
8
AGND
21 D4
D3
A
9
20
IN
10
11
12
13
14
A
19 D2
IN
AGND
18 D1
AV
DD
17 D0 (LSB)
ENCODE
PWRDN
16 DrV
DD
15 DGND
–6–
REV. D
AD9214
TERMINOLOGY
Harmonic Distortion, Third
Analog Bandwidth
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a “best straight line”
determined by a least square curve fit.
Aperture Delay
The delay between the 50% point of the rising edge of the
ENCODE command and the instant at which the analog input
is sampled.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed limit.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Maximum Conversion Rate
Differential Analog Input Resistance, Differential Analog
Input Capacitance and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the capaci-
tance and differential input impedances are measured with a
network analyzer.
The encode rate at which parametric testing is performed.
Output Propagation Delay
The delay between a differential crossing of ENCODE and
ENCODE and the time when all output data bits are within
valid logic levels.
Noise (for any range within the ADC)
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differen-
tial voltage is computed by observing the voltage on a single
pin and subtracting the voltage from the other pin, which is
180 degrees out of phase. Peak-to-peak differential is computed
by rotating the inputs phase 180 degrees and taking the peak
measurement again. Then the difference is computed between
both peak measurements.
FSdBm − SNRdBc − SignaldBFS
VNOISE
= Z × 0.001×10
10
Where Z is the input impedance, FS is the full-scale of the
device for the frequency in question, SNR is the value for the
particular input level and Signal is the signal level within the
ADC reported in dB below full-scale. This value includes both
thermal and quantization noise.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Power Supply Rejection Ratio (PSRR)
The ratio of a change in input offset voltage to a change in
power supply voltage.
Effective Number of Bits
The effective number of bits (ENOB) is calculated from the
measured SNR based on the equation:
Signal-to-Noise-and-Distortion (SINAD)
The ratio of the rms signal amplitude (set 0.5 dB below full
scale) to the rms value of the sum of all other spectral compo-
nents, including harmonics but excluding dc.
Full Scale
Actual
SINADMEASURED – 1.76 dB + 20log
Signal-to-Noise Ratio (without Harmonics)
ENOB =
6.02
The ratio of the rms signal amplitude (set at 0.5 dB below full
scale) to the rms value of the sum of all other spectral compo-
nents, excluding the first five harmonics and dc.
Encode Pulsewidth/Duty Cycle
Pulsewidth high is the minimum amount of time that the ENCODE
pulse should be left in Logic “1” state to achieve rated performance;
pulsewidth low is the minimum time ENCODE pulse should be left
in low state. See timing implications of changing tENCH in text. At a
given clock rate, these specs define an acceptable Encode duty cycle.
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious compo-
nent may or may not be a harmonic. May be reported in dBc
(i.e., degrades as signal level is lowered), or dBFS (always
related back to converter full scale).
Full-Scale Input Power
Expressed in dBm. Computed using the following equation:
Two-Tone Intermodulation Distortion Rejection
2
The ratio of the rms value of either input tone to the rms value
of the worst third order intermodulation product; reported in dBc.
V
FULL SCALE rms
ZINPUT
0.001
PowerFULL SCALE = 10log
Two-Tone SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an intermodulation distortion product. May
be reported in dBc (i.e., degrades as signal level is lowered), or
in dBFS (always related back to converter full scale).
Gain Error
Gain error is the difference between the measured and ideal full
scale input voltage range of the ADC.
Worst Other Spur
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
worst spurious component (excluding the second and third
harmonic) reported in dBc.
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
REV. D
–7–
AD9214
Transient Response Time
Out-of-Range Recovery Time
Transient response is defined as the time it takes for the ADC
to reacquire the analog input after a transient from 10% above
negative full scale to 10% below positive full scale.
Out-of-range recovery time is the time it takes for the ADC to
reacquire the analog input after a transient from 10% above
positive full scale to 10% above negative full scale, or from 10%
below negative full scale to 10% below positive full scale.
EQUIVALENT CIRCUITS
AV
DD
AV
DD
V
30k⍀
40⍀
15k⍀
30k⍀
40⍀
REF
REF
10k⍀
A
A
IN
IN
15k⍀
10k⍀
Figure 2. Analog Input Stage
Figure 5. REF Configured as an Output
AV
DD
2.6k⍀
600⍀
ENCODE
REF
10k⍀
2.6k⍀
Figure 3. Encode Inputs
Figure 6. REF Configured as an Input
DV
DD
40⍀
DX
Figure 4. Digital Output Stage
–8–
REV. D
Typical Performance Characteristics–AD9214
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
ENCODE: 105MSPS
: 50.3MHz @ –0.5dBFS
SNR: 53.0dB
ENOB: 8.5 BITS
SFDR: 64dBFS
ENCODE: 65MSPS
A
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
A : 15.3MHz @ –0.5dBFS
IN
IN
SNR: 56.9dB
ENOB: 9.2 BITS
SFDR: 70dB
52.5
0
52.5
0
FREQUENCY– MHz
FREQUENCY – MHz
TPC 1. FFT: fS = 105 MSPS, fIN = ~50.3 MHz; AIN = –0.5 dBFS
Differential, 1 V p-p Analog Input Range
TPC 4. FFT: fS = 65 MSPS, fIN = 15.3 MHz (2 V p-p) with
AD8138 Driving AIN
100
0
ENCODE: 80MSPS
IN
3RD
A
: 70.3MHz @ –0.5dBFS
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
SNR: 54.0dB
ENOB: 8.5 BITS
SFDR: 64dBFS
90
2ND
80
70
SFDR
60
50
40
10
20
30
40
50
60
70
0
40
0
FREQUENCY – MHz
A
IN
FREQUENCY – MHz
TPC 2. FFT: fS = 80 MSPS, fIN = 70 MHz; AIN = –0.5 dBFS,
1 V p-p Analog Input Range
TPC 5. Harmonic Distortion (Second and Third) and SFDR
vs. AIN Frequency (1 V p-p, fS = 105 MSPS)
85
0
ENCODE: 105MSPS
IN
SNR: 52.6dB
ENOB: 8.4 BITS
SFDR: 62.6dBFS
3RD
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
A
: 70.3MHz @ –0.5dBFS
80
75
2ND
70
SFDR
65
60
55
50
45
40
25
50
75
0
52.5
0
A
FREQUENCY – MHz
FREQUENCY– MHz
IN
TPC 3. FFT: fS = 105 MSPS; fIN = 70 MHz (1 V p-p)
TPC 6. Harmonic Distortion (Second and Third) and SFDR
vs. AIN Frequency (1 V p-p, fS = 80 MSPS)
REV. D
–9–
AD9214
75
70
65
60
55
50
100
SFDR – 1V p–p
SFDR – 2V p–p
90
2ND
80
70
3RD
SINAD – 1V p–p
SFDR
SINAD – 2V p–p
60
50
45
40
40
0
80
ENCODE RATE – MSPS
100
120
20
40
FREQUENCY – MHz
60
80
20
40
60
TPC 7. Harmonic Distortion (Second and Third) and SFDR
vs. AIN Frequency (1 V p-p and 2 V p-p, fS = 65 MSPS)
TPC 10. SINAD and SFDR vs. Encode Rate (fIN = 10.3 MHz;
1 V p-p and 2 V p-p)
0
75
ENCODE: 80MSPS
SFDR – 80MSPS
A
: 29.3MHz @ –6dBFS
30.3MHz @ –6dBFS
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
IN
70
SFDR: 74dBFS
65
SFDR – 105MSPS
60
55
50
SINAD – 80MSPS
45
SINAD – 105MSPS
40
35
30
2
4
6
8
10
40
0
PULSEWIDTH HIGH – ns
FREQUENCY – MHz
TPC 8. Two-Tone Intermodulation Distortion (29.3 MHz,
30.3 MHz; 1 V p-p, fS = 80 MSPS)
TPC 11. SINAD and SFDR vs. Encode Pulsewidth High
(1 V p-p)
0
120
100
12
10
ENCODE: 105MSPS
–10
A
: 30MHz @ –6dBFS
31MHz @ –6dBFS
IN
–20 SFDR: 73dBFS
I
AVDD
–30
–40
–50
–60
–70
–80
–90
80
8
60
40
6
4
I
DrVDD
20
0
2
0
–100
0
20
40
60
80
100
120
52.5
0
ENCODE RATE – MSPS
FREQUENCY – MHz
TPC 9. Two-Tone Intermodulation Distortion (30 MHz and
31 MHz; 1 V p-p, fS = 105 MSPS)
TPC 12. IAVDD and IDrV vs. Encode Rate (fAIN = 10.3 MHz,
–0.5 dBFS, and –3 dBFS) CLOAD on Digital Outputs ~7 pF
DD
–10–
REV. D
AD9214
1.40
58
56
54
52
50
48
1.35
1.30
SNR 10.3MHz/105MSPS
SINAD 10.3MHz/105MSPS
1.25
1.20
1.15
1.10
46
44
–500 –400 –300 –200 –100
0
100 200 300 400 500
–40
0
40
80
I
– A
TEMPERATURE – ؇C
REF
TPC 13. SINAD/SNR vs. Temperature (fAIN = 10.3 MHz,
fENCODE = 105 MSPS, 1 V p-p)
TPC 16. ADC Reference vs. Current Load
4.0
3.5
3.0
2.5
2.0
1.00
0.75
0.50
0.25
0.00
1.5
1.0
0.5
0.0
–0.25
–0.50
–0.75
–1.00
–40
0
128
256
384
512
640
768
896
1024
0
40
80
TEMPERATURE – ؇C
CODE
TPC 14. ADC Gain vs. Temperature (with External 1.25 V
Reference)
TPC 17. INL @ 80 MSPS
1.240
1.00
0.75
0.50
0.25
0.00
1.235
1.230
–0.25
–0.50
–0.75
–1.00
1.225
1.220
–40
0
40
80
0
128
256
384
512
640
768
896
1024
TEMPERATURE –؇C
CODE
TPC 15. ADC Reference vs. Temperature (with 200 µA Load)
TPC 18. DNL @ 80 MSPS
REV. D
–11–
AD9214
THEORY OF OPERATION
DFS/GAIN
The AD9214 architecture is a bit-per-stage pipeline converter
utilizing switch capacitor techniques. These stages determine
the 7 MSBs and drive a 3-bit flash. Each stage provides suffi-
cient overlap and error correction allowing optimization of
comparator accuracy. The input buffer is differential and both
inputs are internally biased. This allows the most flexible use of
ac or dc and differential or single-ended input modes. The out-
put staging block aligns the data, carries out the error correction
and feeds the data to output buffers. The output buffers are
powered from a separate supply, allowing support of different
logic families. During power-down, the outputs go to a high
impedance state.
The DFS/GAIN (Data Format Select/Gain) input (Pin 2)
controls both the output data format and gain (analog input volt-
age range) of the ADC. The table below describes its operation.
Table I. Data Format and Gain Configuration
External
DFS/GAIN
Connection
Differential
Analog Input
Voltage Range
Output Data Format
AGND
AVDD
REF
1 V p-p
1 V p-p
2 V p-p
2 V p-p
Offset Binary
Two’s Complement
Two’s Complement
Offset Binary
Floating
APPLYING THE AD9214
Encoding the AD9214
Driving the Analog Inputs
Any high-speed A/D converter is extremely sensitive to the
quality of the sampling clock provided by the user. A Track/
Hold circuit is essentially a mixer. Any noise, distortion, or
timing jitter on the clock will be combined with the desired
signal at the A/D output. For that reason, considerable care has
been taken in the design of the ENCODE input of the AD9214,
and the user is advised to give commensurate thought to the clock
source. The ENCODE input is fully TTL/CMOS compatible, and
should normally be driven directly from a low jitter, crystal-
controlled TTL/CMOS oscillator.
The analog input to the AD9214 is a differential buffer. As
shown in the equivalent circuits, each of the differential inputs is
internally dc biased at ~AVDD/3 to allow ac-coupling of the
analog input signal. The analog signal may be dc-coupled as
well. In this case, the dc load will be equivalent to ~10 kΩ to
AVDD/3, and the dc common-mode level of the analog signals
should be within the range of AVDD/3 200 mV. For best dynamic
performance, impedances at AIN and AIN should match.
Driving the analog input differentially optimizes ac performance,
minimizing even order harmonics and taking advantage of
common-mode rejection of noise. A differential signal may be
transformer-coupled, as illustrated in Figure 8, or driven from a
high-performance differential amplifier such as the AD8138
illustrated in Figure 9.
The ENCODE input is internally biased, allowing the user to
ac-couple in the clock signal. The cleanest clock source is often
a crystal oscillator producing a pure sine wave. Figure 7 illustrates
ac coupling such a source to the ENCODE input.
A
AD9214
IN
50⍀
ANALOG
SIGNAL
25⍀
25⍀
0.1F
ENCODE
AD9214
LOW JITTER CRYSTAL SINE OR
PULSE SOURCE 1V p-p
SOURCE
1:1
A
IN
Figure 7. AC-Coupled Encode Circuit
Figure 8. Single-Ended-to-Differential Conversion Using
a Transformer
Reference Circuit
The reference circuit of the AD9214 is configured by REFSENSE
(Pin 3). By externally connecting REFSENSE to AGND, the
ADC is configured to use the internal reference (~1.25 V), and
the REF pin connection (Pin 4) is configured as an output for
the internal reference voltage.
Special care was taken in the design of the analog input section
of the AD9214 to prevent damage and corruption of data when
the input is overdriven. The optimal input range is 1.0 V p-p, but
the AD9214 can support a 2.0 V p-p input range with some degra-
dation in performance (see DFS/GAIN pin description above).
If REFSENSE is externally connected to AVDD, the ADC is
configured to use an external reference. In this mode, the REF
pin is configured as a reference input, and must be driven by an
external 1.25 V reference.
In either configuration, the analog input voltage range (either
1 V p-p or 2 V p-p as determined by DFS/Gain) will track the
reference voltage linearly, and an external bypass capacitor should
be connected between REF and AGND to reduce noise on the
reference. In practice, no appreciable degradation in performance
occurs when an external reference is adjusted 5%.
–12–
REV. D
AD9214
It should also be noted that extra capacitive loading will increase
output timing and invalidate timing specifications. Digital output
timing is guaranteed with 10 pF loads.
500⍀
AD8138
AD9214
50⍀
ANALOG
SIGNAL
50⍀
15pF
50⍀
500⍀
+
–
A
A
IN
VOCM
+
SOURCE
LAYOUT INFORMATION
AV
–
DD
IN
The schematic of the evaluation board (Figure 10) represents a
typical implementation of the AD9214. A multilayer board is
recommended to achieve best results. It is highly recommended
that high quality, ceramic chip capacitors be used to decouple
each supply pin to ground directly at the device. The pinout of
the AD9214 facilitates ease of use in the implementation of high
frequency, high resolution design practices. All of the digital
outputs and their supply and ground pin connections are segre-
gated to one side of the package, with the inputs on the opposite
side for isolation purposes.
10k⍀
5k⍀
500⍀
500⍀
0.1F
Figure 9. DC-Coupled Analog Input Circuit
POWER SUPPLIES
The AD9214 has two power supplies, AVDD and DrVDD. AVDD
and AGND supply power to all the analog circuitry, the inputs
and the internal timing and digital error correction circuits.
AVDD supply current will vary slightly with encode rate, as noted in
the Typical Performance Characteristics section.
Care should be taken when routing the digital output traces. To
prevent coupling through the digital outputs into the analog
portion of the AD9214, minimal capacitive loading should be
placed on these outputs. It is recommended that a fan-out of
only one gate should be used for all AD9214 digital outputs.
DrVDD and DGND supply only the CMOS digital outputs,
allowing the user to adjust the voltage level to match down-
stream logic.
The layout of the encode circuit is equally critical. Any noise
received on this circuitry will result in corruption in the digitiza-
tion process and lower overall performance. The Encode clock
must be isolated from the digital outputs and the analog inputs.
DrVDD current will vary depending on the voltage level, external
loading capacitance, and the encode frequency. Designs that mini-
mize external load capacitance will reduce power consumption
and reduce supply noise that may affect ADC performance. The
maximum DrVDD current can be calculated as
EVALUATION BOARD
The AD9214 evaluation board offers designers an easy way to
evaluate device performance. The user must supply an analog
input signal, encode clock reference, and power supplies. The
digital outputs of the AD9214 are latched on the evaluation
board, and are available with a data ready signal at a 40-pin
edge connector. Please refer to the evaluation board schematic,
layout, and Bill of Materials.
I
=V
× CLOAD × fencode × N
DrVDD
DrVDD
where N is the number of output bits, 10 in the case of the
AD9214. This maximum current is for the condition of every
output bit switching on every clock cycle, which can only occur
for a full scale square wave at the Nyquist frequency, fENCODE /2.
In practice, IDrV will be the average number of output bits
switching, whichDwD ill be determined by the encode rate and the
characteristics of the analog input signal. The performance
curves section provides a reference of IDrV versus encode rate
for a 10.3 MHz sine wave driving the analDoDg input.
Power Connections
Power to the board is supplied via three detachable, 4-pin power
strips (U4, U9, and U10). These 12 pins should be driven as
outlined in the Table II.
Both power supply connections should be decoupled to ground
at or near the package connections, using high quality, ceramic
chip capacitors. A single ground plane is recommended for all
ground (AGND and DGND) connections.
Table II. Power Supply Connections for AD9214
Evaluation Board
External Supply
Pin
Designator
Required
The PWRDN control pin configures the AD9214 for a sleep
mode when it is logic HIGH. PWRDN floats logic LOW for
normal operation. In sleep mode, the ADC is not active, and
will consume less power. When switching from sleep mode to
normal operation, the ADC will need ~15 clock cycles to recover to
valid output data.
1
3
LVC
+5 V
3 V
+5 V
(Optional Z1 Supply)
–5 V
(Optional Z1 Supply)
5
–5 V
Digital Outputs
7
9
VCC
VDD
DAC
GND
3 V
3 V
5 V
Ground
Care must be taken when designing the data receivers for the
AD9214. It is recommended that the digital outputs drive a
series resistor (e.g., 100 Ω) followed by a gate like the 74LCX821.
To minimize capacitive loading, there should be only one gate
on each output pin. An example of this is shown in the evaluation
board schematic in Figure 10. The series resistors should be
placed as close to the AD9214 as possible to limit the amount of
current that can flow into the output stage. These switching
currents are confined between ground (DGND) and the DrVDD
pins. Standard TTL gates should be avoided since they can
appreciably add to the dynamic switching currents of the AD9214.
11
2, 4, 6,
8, 10, 12
Please note that the +5 V and –5 V supplies are optional, and
only required if the user adds differential op amp Z1 to the board.
REV. D
–13–
AD9214
Reference Circuit
Analog Input
The evaluation board is configured at assembly to use the
AD9214’s on-board reference. To supply an external reference,
the user must connect the REFSENSE pin to VCC by removing
the jumper block connecting E25 to E26, and placing it between
E19 and E24. In this configuration, an external 1.25 V reference
must be connected to jumper connection E23. Jumper connections
E19–E21, E24, and resistors R13–R14 are omitted at assembly,
and not used in the evaluation of the AD9214.
The analog input signal is connected to the evaluation board by
SMB connector J1. As configured at assembly, the signal is ac
coupled by capacitor C10 to transformer T1. This 1:1 transformer
provides a 50 Ω termination for connector J1 via 25 Ω resistors
R1 and R4. T1 also converts the signal at J1 into a differential
signal for the analog inputs of the AD9214. Resistor R3, normally
omitted, can be used to terminate J1 if the transformer is removed.
The user can reconfigure the board to drive the AD9214 single-
endedly by removing the jumper block between E1 and E3, and
replacing it between E3 and E2. In this configuration, capacitor
C2 stabilizes the self-bias of AIN, and resistor R2 provides a
matched impedance for a 50 Ω source at J1.
Gain/Data Format
The evaluation board is assembled with the DFS/GAIN pin
connected to ground; this configures the AD9214 for a 1 V p-p
analog input range, and offset binary data format. The user may
remove this jumper and replace it to make one of the connections
described in the table below to configure the AD9214 for different
gain and output data format options.
Transformer T1 can be bypassed by moving the jumper normally
between E40 and E38 to connect E40 to E37, and moving the
jumper normally between E39 and E10 to connect E7 to E10.
In this configuration, the analog input of the AD9214 is driven
single ended, directly from J1; and R3 (normally omitted) should
be installed to terminate any cable connected to J1.
Table III. Data Format and Gain Configuration for
Evaluation Board
DFS/GAIN
Jumper
Using the AD8138
DFS/GAIN Differential Output Data
An optional driver circuit for the analog input, based on the
AD8138 differential amplifier, is included in the layout of the
AD9214 evaluation board. This portion of the evaluation circuit
is not populated when the board is manufactured, but can be
easily be added by the user. Resistors R5, R16, R18, and R25
are the feedback network that sets the gain of the AD8138.
Resistors R23 and R24 set the common-mode voltage at the
output of the op amp. Resistors R27 and R28, and capacitor
C15, form a low-pass filter at the output of the AD8138, limiting
its noise contribution into the AD9214.
Placement Connection AIN Range
Format
E18 to E12 AGND
E16 to E11 AVDD
E15 to E14 REF
E17 to E13 Floating
1 V p-p
1 V p-p
2 V p-p
2 V p-p
Offset Binary
Two’s Complement
Two’s Complement
Offset Binary
Power-Down
The evaluation board is configured at assembly so that the
PWRDN input floats low for normal operating condition. The
user may add a jumper between option holes E5 and E6 to
connect PWRDN to AVCC, configuring the AD9214 for power-
down mode.
Once the drive circuit is populated, the user should remove the
jumper block normally between E40 and E38, and place it between
E40 and E41. This will ac-couple the analog input signal from
SMB connector J1 to the AD8138 drive circuit. The user will also
need to remove the jumper blocks that normally connect E39 to
E10 and E1 to E3 to remove transformer T1 from the circuit.
Encode Signal and Distribution
The encode input signal should drive SMB connector J5, which
has an on-board 50 Ω termination. A standard CMOS compatible
pulse source is recommended. Alternatively, the user can adjust
the dc level of an ac-coupled clock source by adding resistor
R11, normally omitted. J5 drives the AD9214 ENCODE input
and one gate of U12, which buffers and distributes the clock
signal to the on-board latch (U3), the reconstruction DAC
(U11), and the output data connector (U2). The board comes
assembled with timing options optimized for the DAC and latch;
the user may invert the DR signal at Pin 37 of edge connector
U2 by removing the jumper block between E34 and E35, and
reinstalling it between E35 and E36.
DAC Reconstruction Circuit
The data available at output connector U2 is also reconstructed by
DAC U11, the AD9752. This 12-bit, high-speed digital-to-analog
converter is included as a tool in setting up and debugging the
evaluation board. It should not be used to measure the per-
formance of the AD9214, as its performance will not accurately
reflect the performance of the ADC. The DAC’s output, available
at J2, will drive 50 Ω. The user can add a jumper block between
E8 and E9 to activate the SLEEP function of the DAC.
–14–
REV. D
AD9214
AD9214/PCB Bill of Material
#
Quantity Reference Designator
Device
Package
Value
1
1
N/A
PCB
2
3
4
5
6
7
8
9
19
4
1
4
4
4
1
2
C1–C3, C5–C14, C16–C20, C25–C28
C21–C24
C4
R1, R2, R4, R8
R7, R10, R12, R17
U5–U8
R21
Capacitor
Capacitor
Capacitor
Resistor
Resistor
Resistor
Resistor
Resistor
603
CAPTAJD
603
1206
1206
RPAK_742
1206
1206
0.1 µF
10 µF
0.01 µF
25 Ω
50 Ω
100 Ω
0 Ω
R6, R9
2000 Ω
10
37
E1–E6, E8–E9, E11–E27, E29, E31–E41
Test Points
Jumper Connections
TSW-120-07-G-S
SMT-100-BK-G
11
12
13
14
15
16
17
18
3
1
1
1
1
1
1
3
J1, J2, J5
U12
U11
U3
U1
Connector
Clock Chip
DAC
SMB
SOIC
SOIC
SOIC
SOIC
51-52-220
SN74LVC86
AD9752
74LCX821
AD9214
Samtec TSW-120-07-G-D
Mini Circuits ADT1-1WT
Newark 95F5966
25.602.5453.0
Latch
ADC/DUT
40-Pin Header
Transformer
Power Strip
Power Connector
U2
T1
U4, U9, U10
The following items are included in the PCB design, but are omitted at assembly.
19
20
21
22
23
24
25
26
27
28
29
3
2
1
4
1
1
3
2
3
1
1
C1, C20, C28
C30, C29
C15
R5, R18, R25, R26
R23
Capacitor
Capacitor
Capacitor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Op Amp
603
CAPTAJD
603
0.1 µF
10 µF
15 pF
500 Ω
1 kΩ
4 kΩ
User Select
N/A
50 Ω
1206
1206
1206
1206
1206
1206
1206
SOIC
R24
R11, R15, R16
R13, R14
R27, R28, R3
R19
0 Ω
AD8138
Z1
REV. D
–15–
AD9214
Figure 10. PCB Schematic
–16–
REV. D
AD9214
Figure 11. PCB Top Side Silkscreen
Figure 14. PCB Bottom Side Copper
\
Figure 12. PCB Top Side Copper
Figure 15. PCB Ground Layer—Layer TBD
Figure 13. PCB Bottom Side Silkscreen
Figure 16. PCB Power Layers—Layers 3 and 4
REV. D
–17–
AD9214
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
28-Lead Shrink Small Outline Package
(RS-28)
0.407 (10.34)
0.397 (10.08)
28
15
1
14
0.07 (1.79)
0.078 (1.98)
PIN 1
0.066 (1.67)
0.068 (1.73)
0.03 (0.762)
0.022 (0.558)
8°
0°
0.0256
(0.65)
BSC
0.015 (0.38)
0.010 (0.25)
0.008 (0.203)
0.002 (0.050)
SEATING
PLANE
0.009 (0.229)
0.005 (0.127)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE
ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–18–
REV. D
AD9214
Revision History
Location
Page
Data Sheet changed from REV. C to REV. D.
Edit to Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
TPC 15 replaced with new figure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edit to Figure 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
07/01—Data Sheet changed from REV. B to REV. C.
Edit to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
05/01—Data Sheet changed from REV. A to REV. B.
Changes to PSRR Specifications in AD9214-65, AD9214-80, AD9214-105 Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Change to SNR Specifications in AD9214-105 Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Changes to THIRD HARMONIC DISTORTION Specifications in AD9214-105 Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
01/01—Data Sheet changed from REV. 0 to REV. A.
Changes to DC Specifications in AD9214-65, AD9214-80, AD9214-105 Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to AC Specifications in AD9214-65, AD9214-105 Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
REV. D
–19–
–20–
相关型号:
AD9214BRS-RL80
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28
ROCHESTER
AD9214BRSZ-105
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28
ROCHESTER
AD9214BRSZ-80
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28
ROCHESTER
AD9214BRSZ-RL65
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28
ROCHESTER
AD9214BRSZ-RL80
1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28, PLASTIC, SSOP-28
ROCHESTER
©2020 ICPDF网 联系我们和版权申明