LM111W-MLS [ROCHESTER]
Comparator, 1 Func, 4000uV Offset-Max, 200ns Response Time, BIPolar, CDSO10, CERPACK-10;型号: | LM111W-MLS |
厂家: | Rochester Electronics |
描述: | Comparator, 1 Func, 4000uV Offset-Max, 200ns Response Time, BIPolar, CDSO10, CERPACK-10 放大器 CD |
文件: | 总24页 (文件大小:1120K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
January 2001
LM111/LM211/LM311
Voltage Comparator
1.0 General Description
The LM111, LM211 and LM311 are voltage comparators that
have input currents nearly a thousand times lower than
devices like the LM106 or LM710. They are also designed to
operate over a wider range of supply voltages: from standard
15V op amp supplies down to the single 5V supply used for
IC logic. Their output is compatible with RTL, DTL and TTL
as well as MOS circuits. Further, they can drive lamps or
relays, switching voltages up to 50V at currents as high as
50 mA.
the devices are also much less prone to spurious oscilla-
tions. The LM111 has the same pin configuration as the
LM106 and LM710.
The LM211 is identical to the LM111, except that its perfor-
mance is specified over a −25˚C to +85˚C temperature range
instead of −55˚C to +125˚C. The LM311 has a temperature
range of 0˚C to +70˚C.
2.0 Features
n Operates from single 5V supply
n Input current: 150 nA max. over temperature
n Offset current: 20 nA max. over temperature
n Differential input voltage range: 30V
n Power consumption: 135 mW at 15V
Both the inputs and the outputs of the LM111, LM211 or the
LM311 can be isolated from system ground, and the output
can drive loads referred to ground, the positive supply or the
negative supply. Offset balancing and strobe capability are
provided and outputs can be wire OR’ed. Although slower
than the LM106 and LM710 (200 ns response time vs 40 ns)
3.0 Typical Applications (Note 3)
Offset Balancing
Strobing
00570436
00570437
Note: Do Not Ground Strobe Pin. Output is turned off when current is
pulled from Strobe Pin.
Increasing Input Stage Current (Note 1)
Detector for Magnetic Transducer
00570438
Note 1: Increases typical common mode slew from 7.0V/µs to 18V/µs.
00570439
© 2004 National Semiconductor Corporation
DS005704
www.national.com
3.0 Typical Applications (Note 3) (Continued)
Digital Transmission Isolator
Relay Driver with Strobe
00570440
00570441
*Absorbs inductive kickback of relay and protects IC from severe voltage
++
transients on V line.
Note: Do Not Ground Strobe Pin.
Strobing off Both Input and Output Stages (Note 2)
00570442
Note: Do Not Ground Strobe Pin.
Note 2: Typical input current is 50 pA with inputs strobed off.
Note 3: Pin connections shown on schematic diagram and typical applications are for H08 metal can package.
Positive Peak Detector
Zero Crossing Detector Driving MOS Logic
00570424
00570423
*Solid tantalum
www.national.com
2
4.0 Absolute Maximum Ratings for
the LM111/LM211(Note 10)
LM111
−55˚C to 125˚C
−25˚C to 85˚C
260˚C
LM211
Lead Temperature (Soldering, 10 sec)
Voltage at Strobe Pin
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
Small Outline Package
Vapor Phase (60 seconds)
Infrared (15 seconds)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
V+−5V
Total Supply Voltage (V84
Output to Negative Supply Voltage
(V74
Ground to Negative Supply Voltage
(V14
)
36V
260˚C
)
50V
215˚C
220˚C
)
30V
30V
Differential Input Voltage
Input Voltage (Note 4)
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
15V
Output Short Circuit Duration
Operating Temperature Range
10 sec
ESD Rating (Note 11)
300V
Electrical Characteristics (Note 6) for the LM111 and LM211
Parameter
Input Offset Voltage (Note 7)
Input Offset Current
Input Bias Current
Conditions
Min
Typ
Max
3.0
10
Units
mV
nA
TA=25˚C, RS≤50k
0.7
TA=25˚C
4.0
TA=25˚C
60
100
nA
Voltage Gain
TA=25˚C
40
200
200
0.75
V/mV
ns
Response Time (Note 8)
Saturation Voltage
TA=25˚C
VIN≤−5 mV, IOUT=50 mA
TA=25˚C
1.5
V
Strobe ON Current (Note 9)
Output Leakage Current
TA=25˚C
2.0
0.2
5.0
10
mA
nA
VIN≥5 mV, VOUT=35V
TA=25˚C, ISTROBE=3 mA
RS≤50 k
Input Offset Voltage (Note 7)
Input Offset Current (Note 7)
Input Bias Current
4.0
20
mV
nA
nA
V
150
13.0
Input Voltage Range
V+=15V, V−=−15V, Pin 7
Pull-Up May Go To 5V
V+≥4.5V, V−=0
−14.5
13.8,-14.7
0.23
Saturation Voltage
0.4
V
VIN≤−6 mV, IOUT≤8 mA
VIN≥5 mV, VOUT=35V
TA=25˚C
Output Leakage Current
Positive Supply Current
Negative Supply Current
0.1
5.1
4.1
0.5
6.0
5.0
µA
mA
mA
TA=25˚C
Note 4: This rating applies for 15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 5: The maximum junction temperature of the LM111 is 150˚C, while that of the LM211 is 110˚C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line
package is 110˚C/W, junction to ambient.
Note 6: These specifications apply for V = 15V and Ground pin at ground, and −55˚C≤T ≤+125˚C, unless otherwise stated. With the LM211, however, all
S
A
temperature specifications are limited to −25˚C≤T ≤+85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single
A
5V supply up to 15V supplies.
Note 7: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and R .
S
Note 8: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 9: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin
to ground; it should be current driven at 3 to 5 mA.
Note 10: Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.
Note 11: Human body model, 1.5 kΩ in series with 100 pF.
3
www.national.com
5.0 Absolute Maximum Ratings for
the LM311(Note 12)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Output Short Circuit Duration
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 10 sec)
Voltage at Strobe Pin
10 sec
0˚ to 70˚C
−65˚C to 150˚C
260˚C
V+−5V
Total Supply Voltage (V84
Output to Negative Supply Voltage
(V74
Ground to Negative Supply Voltage
(V14
)
36V
Soldering Information
Dual-In-Line Package
)
40V
Soldering (10 seconds)
260˚C
Small Outline Package
)
30V
30V
Vapor Phase (60 seconds)
Infrared (15 seconds)
215˚C
220˚C
Differential Input Voltage
Input Voltage (Note 13)
Power Dissipation (Note 14)
ESD Rating (Note 19)
15V
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
500 mW
300V
Electrical Characteristics (Note 15) for the LM311
Parameter
Input Offset Voltage (Note 16)
Input Offset Current(Note 16)
Input Bias Current
Conditions
TA=25˚C, RS≤50k
Min
Typ
2.0
Max
7.5
50
Units
mV
nA
TA=25˚C
6.0
TA=25˚C
100
200
200
0.75
250
nA
Voltage Gain
TA=25˚C
40
V/mV
ns
Response Time (Note 17)
Saturation Voltage
TA=25˚C
VIN≤−10 mV, IOUT=50 mA
TA=25˚C
1.5
5.0
50
V
Strobe ON Current (Note 18)
Output Leakage Current
TA=25˚C
2.0
0.2
mA
nA
VIN≥10 mV, VOUT=35V
TA=25˚C, ISTROBE=3 mA
V− = Pin 1 = −5V
RS≤50K
Input Offset Voltage (Note 16)
Input Offset Current (Note 16)
Input Bias Current
10
70
mV
nA
nA
V
300
13.0
0.4
Input Voltage Range
−14.5
13.8,−14.7
0.23
Saturation Voltage
V+≥4.5V, V−=0
VIN≤−10 mV, IOUT≤8 mA
TA=25˚C
V
Positive Supply Current
Negative Supply Current
5.1
4.1
7.5
5.0
mA
mA
TA=25˚C
Note 12: “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.”
Note 13: This rating applies for 15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 14: The maximum junction temperature of the LM311 is 110˚C. For operating at elevated temperature, devices in the H08 package must be derated based
on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line package is 100˚C/W, junction to
ambient.
<
<
+70˚C, unless otherwise specified. The offset voltage, offset current and
Note 15: These specifications apply for V = 15V and Pin 1 at ground, and 0˚C
T
S
A
bias current specifications apply for any supply voltage from a single 5V supply up to 15V supplies.
Note 16: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and R .
S
Note 17: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 18: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe
pin to ground; it should be current driven at 3 to 5 mA.
Note 19: Human body model, 1.5 kΩ in series with 100 pF.
www.national.com
4
6.0 LM111/LM211 Typical Performance Characteristics
Input Bias Current
Input Bias Current
00570443
00570444
Input Bias Current
Input Bias Current
00570446
00570445
Input Bias Current
Input Bias Current
00570447
00570448
5
www.national.com
6.0 LM111/LM211 Typical Performance Characteristics (Continued)
Input Bias Current
Input Overdrives
Input Bias Current
Input Overdrives
00570450
00570449
Response Time for Various
Input Overdrives
Input Bias Current
00570451
00570452
Response Time for Various
Input Overdrives
Output Limiting Characteristics
00570454
00570453
www.national.com
6
6.0 LM111/LM211 Typical Performance Characteristics (Continued)
Supply Current
Supply Current
00570455
00570456
Leakage Currents
00570457
7.0 LM311 Typical Performance Characteristics
Input Bias Current
Input Offset Current
00570458
00570459
7
www.national.com
7.0 LM311 Typical Performance Characteristics (Continued)
Offset Error
Input Characteristics
00570461
00570460
Common Mode Limits
Transfer Function
00570462
00570463
Response Time for Various
Input Overdrives
Response Time for Various
Input Overdrives
00570465
00570464
www.national.com
8
7.0 LM311 Typical Performance Characteristics (Continued)
Response Time for Various
Input Overdrives
Output Saturation Voltage
00570466
00570467
Response Time for Various
Input Overdrives
Output Limiting Characteristics
00570469
00570468
Supply Current
Supply Current
00570470
00570471
9
www.national.com
7.0 LM311 Typical Performance Characteristics (Continued)
Leakage Currents
00570472
lead between the resistors and the input pins can result
8.0 Application Hints
in oscillations that are very hard to damp. Twisting these
input leads tightly is the only (second best) alternative to
placing resistors close to the comparator.
8.1 CIRCUIT TECHNIQUES FOR AVOIDING
OSCILLATIONS IN COMPARATOR APPLICATIONS
5. Since feedback to almost any pin of a comparator can
result in oscillation, the printed-circuit layout should be
engineered thoughtfully. Preferably there should be a
groundplane under the LM111 circuitry, for example, one
side of a double-layer circuit card. Ground foil (or, posi-
tive supply or negative supply foil) should extend be-
tween the output and the inputs, to act as a guard. The
foil connections for the inputs should be as small and
compact as possible, and should be essentially sur-
rounded by ground foil on all sides, to guard against
capacitive coupling from any high-level signals (such as
the output). If pins 5 and 6 are not used, they should be
shorted together. If they are connected to a trim-pot, the
trim-pot should be located, at most, a few inches away
from the LM111, and the 0.01 µF capacitor should be
installed. If this capacitor cannot be used, a shielding
printed-circuit foil may be advisable between pins 6 and
7. The power supply bypass capacitors should be lo-
cated within a couple inches of the LM111. (Some other
comparators require the power-supply bypass to be lo-
cated immediately adjacent to the comparator.)
When a high-speed comparator such as the LM111 is used
with fast input signals and low source impedances, the out-
put response will normally be fast and stable, assuming that
the power supplies have been bypassed (with 0.1 µF disc
capacitors), and that the output signal is routed well away
from the inputs (pins 2 and 3) and also away from pins 5 and
6.
However, when the input signal is a voltage ramp or a slow
sine wave, or if the signal source impedance is high (1 kΩ to
100 kΩ), the comparator may burst into oscillation near the
crossing-point. This is due to the high gain and wide band-
width of comparators like the LM111. To avoid oscillation or
instability in such a usage, several precautions are recom-
mended, as shown in Figure 1 below.
1. The trim pins (pins 5 and 6) act as unwanted auxiliary
inputs. If these pins are not connected to a trim-pot, they
should be shorted together. If they are connected to a
trim-pot, a 0.01 µF capacitor C1 between pins 5 and 6
will minimize the susceptibility to AC coupling. A smaller
capacitor is used if pin 5 is used for positive feedback as
in Figure 1.
6. It is a standard procedure to use hysteresis (positive
feedback) around a comparator, to prevent oscillation,
and to avoid excessive noise on the output because the
comparator is a good amplifier for its own noise. In the
circuit of Figure 2, the feedback from the output to the
positive input will cause about 3 mV of hysteresis. How-
ever, if RS is larger than 100Ω, such as 50 kΩ, it would
not be reasonable to simply increase the value of the
positive feedback resistor above 510 kΩ. The circuit of
Figure 3 could be used, but it is rather awkward. See the
notes in paragraph 7 below.
2. Certain sources will produce a cleaner comparator out-
put waveform if a 100 pF to 1000 pF capacitor C2 is
connected directly across the input pins.
3. When the signal source is applied through a resistive
network, RS, it is usually advantageous to choose an RS'
of substantially the same value, both for DC and for
dynamic (AC) considerations. Carbon, tin-oxide, and
metal-film resistors have all been used successfully in
comparator input circuitry. Inductive wirewound resistors
are not suitable.
4. When comparator circuits use input resistors (eg. sum-
ming resistors), their value and placement are particu-
larly important. In all cases the body of the resistor
should be close to the device or socket. In other words
there should be very little lead length or printed-circuit
foil run between comparator and resistor to radiate or
pick up signals. The same applies to capacitors, pots,
etc. For example, if RS=10 kΩ, as little as 5 inches of
www.national.com
10
tive supply. This signal is centered around the nominal
voltage at pin 5, so this feedback does not add to the
VOS of the comparator. As much as 8 mV of VOS can be
trimmed out, using the 5 kΩ pot and 3 kΩ resistor as
shown.
8.0 Application Hints (Continued)
7. When both inputs of the LM111 are connected to active
signals, or if a high-impedance signal is driving the
positive input of the LM111 so that positive feedback
would be disruptive, the circuit of Figure 1 is ideal. The
positive feedback is to pin 5 (one of the offset adjust-
ment pins). It is sufficient to cause 1 to 2 mV hysteresis
and sharp transitions with input triangle waves from a
few Hz to hundreds of kHz. The positive-feedback signal
across the 82Ω resistor swings 240 mV below the posi-
8. These application notes apply specifically to the LM111,
LM211, LM311, and LF111 families of comparators, and
are applicable to all high-speed comparators in general,
(with the exception that not all comparators have trim
pins).
00570429
Pin connections shown are for LM111H in the H08 hermetic package
FIGURE 1. Improved Positive Feedback
00570430
Pin connections shown are for LM111H in the H08 hermetic package
FIGURE 2. Conventional Positive Feedback
11
www.national.com
8.0 Application Hints (Continued)
00570431
FIGURE 3. Positive Feedback with High Source Resistance
9.0 Typical Applications (Pin numbers
refer to H08 package)
Zero Crossing Detector Driving MOS Switch
100 kHz Free Running Multivibrator
00570413
00570414
*TTL or DTL fanout of two
www.national.com
12
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
10 Hz to 10 kHz Voltage Controlled Oscillator
00570415
*Adjust for symmetrical square wave time when V = 5 mV
IN
†
Minimum capacitance 20 pF Maximum frequency 50 kHz
Driving Ground-Referred Load
Using Clamp Diodes to Improve Response
00570417
00570416
*Input polarity is reversed when using pin 1 as output.
TTL Interface with High Level Logic
00570418
*Values shown are for a 0 to 30V logic swing and a 15V threshold.
†
May be added to control speed and reduce susceptibility to noise spikes.
13
www.national.com
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Crystal Oscillator
Comparator and Solenoid Driver
00570420
00570419
Precision Squarer
00570421
*Solid tantalum
†
Adjust to set clamp level
www.national.com
14
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Low Voltage Adjustable Reference Supply
00570422
*Solid tantalum
Positive Peak Detector
Zero Crossing Detector Driving MOS Logic
00570424
00570423
*Solid tantalum
Negative Peak Detector
00570425
*Solid tantalum
15
www.national.com
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Precision Photodiode Comparator
00570426
*R2 sets the comparison level. At comparison, the photodiode has less than 5 mV across it, decreasing leakages by an order of magnitude.
Switching Power Amplifier
00570427
www.national.com
16
9.0 Typical Applications (Pin numbers refer to H08 package) (Continued)
Switching Power Amplifier
00570428
17
www.national.com
10.0 Schematic Diagram (Note 20)
00570405
Note 20: Pin connections shown on schematic diagram are for H08 package.
www.national.com
18
11.0 Connection Diagrams
Metal Can Package
00570406
Note: Pin 4 connected to case
Top View
Order Number LM111H, LM111H/883(Note 21) , LM211H or LM311H
See NS Package Number H08C
Dual-In-Line Package
Dual-In-Line Package
00570434
Top View
00570435
Order Number LM111J-8, LM111J-8/883(Note 21),
LM311M, LM311MX or LM311N
See NS Package Number J08A, M08A or N08E
Top View
Order Number LM111J/883(Note 21)
See NS Package Number J14A or N14A
00570433
Order Number LM111W/883(Note 21), LM111WG/883
See NS Package Number W10A, WG10A
Note 21: Also available per JM38510/10304
19
www.national.com
12.0 Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
Order Number LM111H, LM111H/883, LM211H or LM311H
NS Package Number H08C
Cavity Dual-In-Line Package (J)
Order Number LM111J-8, LM111J-8/883
NS Package Number J08A
www.national.com
20
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Dual-In-Line Package (J)
Order Number LM111J/883
NS Package Number J14A
Dual-In-Line Package (M)
Order Number LM311M, LM311MX
NS Package Number M08A
21
www.national.com
12.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Dual-In-Line Package (N)
Order Number LM311N
NS Package Number N08E
Order Number LM111W/883, LM111WG/883
NS Package Number W10A, WG10A
www.national.com
22
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号:
©2020 ICPDF网 联系我们和版权申明