MAX1158BCUP [ROCHESTER]
1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO20, 4.40 MM, TSSOP-20;型号: | MAX1158BCUP |
厂家: | Rochester Electronics |
描述: | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO20, 4.40 MM, TSSOP-20 信息通信管理 光电二极管 转换器 |
文件: | 总16页 (文件大小:980K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-2736; Rev 0; 1/03
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
General Description
Features
The MAX1156/MAX1158/MAX1174 14-bit, low-power,
successive-approximation analog-to-digital converters
(ADCs) feature automatic power-down, a factory-
trimmed internal clock, and a byte-wide parallel inter-
face. The devices operate from a single +4.75V to
+5.25V analog supply and feature a separate digital
supply input for direct interface with +2.7V to +5.25V
digital logic.
ꢀ Byte-Wide Parallel Interface
ꢀ Analog Input Voltage Range: ±±1Vꢀ ±ꢁVꢀ 1 to ±1V
ꢀ Single +4.7ꢁV to +ꢁ.2ꢁV Analog Supply Voltage
ꢀ Interface with +2.7V to +ꢁ.2ꢁV Digital Logic
ꢀ ±±LSB IꢂL ꢃ(aꢄx
ꢀ ±±LSB DꢂL ꢃ(aꢄx
The MAX1156 accepts a 0 to +10V analog input volt-
age range. The MAX1158 accepts a 10V bipolar ana-
log input voltage range, while the MAX1174 accepts a
5V bipolar analog input voltage range. All devices
consume no more than 26.5mW at a sampling rate of
135ksps when using an external reference, and 31mW
when using the internal +4.096V reference.
AutoShutdown™ reduces supply current to 0.4mA (typ)
at 10ksps.
ꢀ Low Supply Current ꢃ(aꢄx
2.9(A ꢃEꢄternal Referencex
3.8(A ꢃInternal Referencex
ꢁµA AutoShutdown Mode
ꢀ S(all Footprint
ꢀ 21-Pin TSSOP Package
The MAX1156/MAX1158/MAX1174 are ideal for high-
performance, battery-powered, data-acquisition appli-
cations. Excellent AC performance (THD = -100dB) and
DC accuracy ( 1ꢀSB ꢁIꢀ) make the MAX1156/
MAX1158/MAX1174 ideal for industrial process control,
instrumentation, and medical applications.
Ordering Information
IꢂPUT
VOLTAGE
RAꢂGE
PIꢂ-
PACKAGE
PART
TEMP RAꢂGE
MAX±±ꢁ6ACUP
0°C to +70°C
0°C to +70°C
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
0 to +10V
0 to +10V
0 to +10V
0 to +10V
The MAX1156/MAX1158/MAX1174 are available in a
20-pin TSSOP package and are fully specified over the
-40°C to +85°C extended temperature range and the
0°C to +70°C commercial temperature range.
MAX1156BCUP
MAX1156AEUP -40°C to +85°C
MAX1156BEUP -40°C to +85°C
Ordering Information continued at end of data sheet.
Applications
Typical Operating Circuit
Temperature Sensing and Monitoring
ꢁndustrial Process Control
ꢁ/O Modules
+5V ANALOG +5V DIGITAL
0.1µF
0.1µF
Data-Acquisition Systems
Precision ꢁnstrumentation
AV
DD
DV
µP DATA
BUS
DD
D0–D7
OR
ANALOG INPUT
AIN
D8–D13
MAX1156
MAX1158
MAX1174
EOC
R/C
CS
REF
REFADJ
HBEN
HIGH
BYTE
0.1µF
10µF
AGND DGND
Pin Configuration appears at end of data sheet.
LOW
BYTE
AutoShutdown is a trademark of Maxim Integrated Products, Inc.
________________________________________________________________ Maxim Integrated Products
±
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Continuous Power Dissipation (T = +70°C)
20-Pin TSSOP (derate 10.9mW/°C above +70°C) .......879mW
A
AGND to DGND.....................................................-0.3V to +0.3V
AIN to AGND .....................................................-16.5V to +16.5V
Operating Temperature Range
MAX11_ _ _CUP..................................................0°C to +70°C
MAX11_ _ _EUP...............................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
REF, REFADJ to AGND............................-0.3V to (AV
+ 0.3V)
DD
CS, R/C, HBEN to DGND .........................................-0.3V to +6V
D_, EOC to DGND ...................................-0.3V to (DV + 0.3V)
DD
Maximum Continuous Current into any Pin.........................50mA
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(AV
= DV
= +5V 5ꢀ, external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
= AV , T = T
to T
,
MAX
DD
DD
REF
REFADJ
REFADJ
DD
A
MIN
unless otherwise noted. Typical values are at T = +25°C.)
A
PARAMETER
DC ACCURACY
SYMBOL
COꢂDITIOꢂS
MIꢂ
TYP
MAX
UꢂITS
Resolution
RES
DNL
14
-1
-1
-2
Bits
Diꢁꢁerential Nonlinearity
No missing codes over temperature
MAX11_ _A
+1
+1
+2
LSB
Integral Nonlinearity
Transition Noise
INL
LSB
MAX11_ _B
RMS noise, external reꢁerence
Internal reꢁerence
0.32
0.34
0
LSB
RMS
Oꢁꢁset Error
Gain Error
Oꢁꢁset Driꢁt
Gain Driꢁt
-10
+10
0.2
mV
0
ꢀFSR
µV/°C
16
1
ppm/°C
AC ACCURACY (ꢁ = 1kHz, V
= ꢁull range, 135ksps)
IN
AIN
Signal-to-Noise Plus Distortion
Signal-to-Noise Ratio
SINAD
SNR
81
82
85
85
dB
dB
dB
dB
Total Harmonic Distortion
Spurious-Free Dynamic Range
AꢂALOG IꢂPUT
THD
-100
103
-86
SFDR
87
MAX1156
0
+10
+10
+5
Input Range
V
V
MAX1158
-10
-5
AIN
MAX1174
MAX1156/MAX1174
MAX1156
Normal operation
5.3
5.3
3.0
7.8
6.0
6.9
10
9.2
Shutdown mode
Shutdown mode
Normal operation
Shutdown mode
MAX1174
Input Resistance
R
kΩ
AIN
13.0
MAX1158
2
_______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
ELECTRICAL CHARACTERISTICS ꢃcontinuedx
(AV
= DV
= +5V 5ꢀ, external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
= AV , T = T
to T
,
MAX
DD
DD
REF
REFADJ
REFADJ
DD
A
MIN
unless otherwise noted. Typical values are at T = +25°C.)
A
PARAMETER
SYMBOL
COꢂDITIOꢂS
≤ +10V
MIꢂ
-0.1
-1.8
-1.8
-1.8
-1.8
TYP
MAX
UꢂITS
MAX1156, 0 ≤ V
+2.0
+1.2
+1.8
+0.4
+1.8
AIN
Normal operation
MAX1158,
-10V ≤ V
≤ +10V
Input Current
I
AIN
Shutdown mode
Normal operation
Shutdown mode
mA
AIN
MAX1174,
-5V ≤ V
≤ +5V
AIN
MAX1158, V
operating mode
= +10V, shutdown mode to
AIN
0.5
0.7
1.4
Input Current Step at Power-Up
I
mA
pF
PU
MAX1174, V
= +5V, shutdown mode to
AIN
1
operating mode
Input Capacitance
C
10
IN
IꢂTERꢂAL REFEREꢂCE
REF Output Voltage
V
4.056
3.8
4.096
35
4.136
V
REF
REF Output Tempco
ppm/°C
mA
REF Short-Circuit Current
EXTERꢂAL REFEREꢂCE
I
10
REF-SC
REF and REFADJ Input Voltage
Range
4.2
V
V
AV
-
AV
-
DD
DD
REFADJ Buꢁꢁer Disable Threshold
REF Input Current
0.4
0.1
Normal mode, ꢁ
= 135ksps
60
0.1
16
100
10
SAMPLE
I
µA
µA
REF
Shutdown mode (Note 1)
REFADJ = AV
REFADJ Input Current
I
REFADJ
DD
DIGITAL IꢂPUTS/OUTPUTS
I
= 0.5mA, DV
= +5.25V
= +2.7V to +5.25V, DV
-
DD
SOURCE
DD
Output High Voltage
Output Low Voltage
Input High Voltage
Input Low Voltage
V
V
V
V
V
OH
AV
0.4
DD
I
= 1.6mA, DV
= +5.25V
= +2.7V to +5.25V,
DD
SINK
V
0.4
OL
AV
DD
0.7 ×
DV
V
IH
DD
0.3 ×
V
IL
DV
DD
Input Leakage Current
Input Hysteresis
Digital input = DV
or 0V
-1
+1
µA
V
DD
V
0.2
15
HYST
Input Capacitance
C
pF
µA
pF
IN
Three-State Output Leakage
Three-State Output Capacitance
I
10
OZ
C
15
OZ
_______________________________________________________________________________________
3
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
ELECTRICAL CHARACTERISTICS ꢃcontinuedx
(AV
= DV
= +5V 5ꢀ, external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
= AV , T = T
to T
,
MAX
DD
DD
REF
REFADJ
REFADJ
DD
A
MIN
unless otherwise noted. Typical values are at T = +25°C.)
A
PARAMETER
POWER SUPPLIES
SYMBOL
COꢂDITIOꢂS
MIꢂ
TYP
MAX
UꢂITS
Analog Supply Voltage
Digital Supply Voltage
AV
DV
4.75
2.70
5.25
5.25
2.9
V
V
DD
DD
MAX1156
External reꢁerence,
135ksps
MAX1158/MAX1174
MAX1156
4
5.3
Analog Supply Current
I
mA
AVDD
3.8
Internal reꢁerence,
135ksps
MAX1158/MAX1174
5.2
0.5
3.7
6.2
Shutdown mode (Note 1), digital input =
DV or 0V
5
µA
Shutdown Supply Current
I
I
DD
SHDN
Standby mode
mA
mA
Digital Supply Current
Power-Supply Rejection
0.75
DVDD
AV
= DV
= +4.75V to +5.25V
DD
1
LSB
DD
TIMIꢂG CHARACTERISTICS ꢃFigures ± and 2x
(AV
= +4.75V to +5.25V 5ꢀ, DV
= +2.7V to AV , external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
=
REFADJ
DD
DD
DD
REF
REFADJ
AV , C
= 20pF, T = T
to T
.)
DD LOAD
A
MIN
MAX
PARAMETER
SYMBOL
COꢂDITIOꢂS
MIꢂ
TYP
MAX
UꢂITS
ksps
µs
Maximum Sampling Rate
Acquisition Time
ꢁ
135
SAMPLE-MAX
t
2
ACQ
Conversion Time
t
4.7
µs
CONV
CS Pulse Width High
t
(Note 2)
(Note 2)
40
40
60
0
ns
CSH
DV
DV
= +4.75V to +5.25V
DD
DD
CS Pulse Width Low
t
ns
ns
ns
CSL
= +2.7V to +5.25V
R/C to CS Fall Setup Time
R/C to CS Fall Hold Time
t
DS
DH
DV
DV
DV
DV
= +4.75V to +5.25V
= +2.7V to +5.25V
= +4.75V to +5.25V
= +2.7V to +5.25V
40
60
DD
DD
DD
DD
t
40
80
CS to Output Data Valid
EOC Fall to CS Fall
t
ns
ns
ns
DO
t
0
DV
DV
DV
DV
DV
DV
DV
= +4.75V to +5.25V
= +2.7V to +5.25V
= +4.75V to +5.25V
= +2.7V to +5.25V
= +4.75V to +5.25V
= +2.7V to +5.25V
40
80
40
80
40
80
DD
DD
DD
DD
DD
DD
CS Rise to EOC Rise
t
EOC
Bus Relinquish Time
t
ns
ns
BR
HBEN Transition to Output Data
Valid
t
1
DO
ꢂote ±: Maximum speciꢁication is limited by automated test equipment.
ꢂote 2: To ensure best perꢁormance, ꢁinish reading the data and wait t beꢁore starting a new acquisition.
BR
4
_______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Typical Operating Characteristics
(AV
= DV
= +5V, external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
= AV , C
= 20pF, T = T
MIN
to
DD
DD
REF
REFADJ
REFADJ
DD LOAD
A
T
MAX
, unless otherwise noted. Typical values are at T = +25°C.) (Typical Application Circuit)
A
SUPPLY CURRENT (AV + DV
DD
)
DD
INL vs. CODE
DNL vs. CODE
MAX1156/58/74 toc02
vs. TEMPERATURE
MAX1156/58/74 toc01
2.5
1.0
0.8
4.80
4.75
4.70
4.65
4.60
4.55
4.50
4.45
4.40
2.0
1.5
5.25V
5.0V
0.6
1.0
0.4
0.5
0.2
0
0
-0.5
-1.0
-1.5
-2.0
-2.5
-0.2
-0.4
-0.6
-0.8
-1.0
4.75V
= 135ksps
f
SAMPLE
SHUTDOWN MODE
BETWEEN CONVERSIONS
0
2000 4000 6000 8000 10000 12000 14000 16000
CODE
0
2000 4000 6000 8000 10000 12000 14000 16000
CODE
80
-40
-20
0
20
40
60
TEMPERATURE (°C)
SUPPLY CURRENT (AV + DV
DD
)
SHUTDOWN CURRENT (AV + DV )
DD DD
DD
vs. SAMPLE RATE
vs. TEMPERATURE
OFFSET ERROR vs. TEMPERATURE
10
1
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
10
8
NO CONVERSIONS
STANDBY MODE
6
4
MAX1174
0.1
2
0
SHUTDOWN MODE
0.01
0.001
-2
-4
-6
-8
-10
MAX1158
MAX1156
V
= 0V
AIN
0.0001
0.01
0.1
1
10
100
1000
-40
-20
0
20
40
60
80
-40
-20
0
20
40
60
80
SAMPLE RATE (ksps)
TEMPERATURE (°C)
TEMPERATURE (°C)
INTERNAL REFERENCE
vs. TEMPERATURE
GAIN ERROR vs. TEMPERATURE
FFT AT 1kHz
0.20
0.15
0.10
0.05
0
4.136
4.126
4.116
4.106
4.096
4.086
4.076
4.066
4.056
0
-20
f
= 131ksps
SAMPLE
-40
-60
-80
-100
-120
-140
-160
-180
-0.05
-0.10
-0.15
-0.20
-40
-20
0
20
40
60
80
0
10
20
30
40
50
60
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
FREQUENCY (kHz)
TEMPERATURE (°C)
_______________________________________________________________________________________
ꢁ
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Typical Operating Characteristics (continued)
(AV
= DV
= +5V, external reꢁerence = +4.096V, C
= 10µF, C
= 0.1µF, V
= AV , C
= 20pF, T = T
to
MIN
DD
DD
REF
REFADJ
REFADJ
DD LOAD
A
T
MAX
, unless otherwise noted. Typical values are at T = +25°C.) (Typical Application Circuit)
A
SINAD vs. FREQUENCY
SFDR vs. FREQUENCY
THD vs. FREQUENCY
100
90
80
70
60
50
40
30
20
10
0
120
100
80
60
40
20
0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
f
= 131ksps
f
= 131ksps
SAMPLE
SAMPLE
f
= 131ksps
SAMPLE
1
10
100
1
10
FREQUENCY (kHz)
100
1
10
FREQUENCY (kHz)
100
FREQUENCY (kHz)
Pin Description
PIꢂ
1
ꢂAME
D4/D12
D5/D13
D6/0
FUꢂCTIOꢂ
Three-State Digital Data Output
2
Three-State Digital Data Output. D13 is the MSB.
Three-State Digital Data Output
3
4
D7/0
Three-State Digital Data Output
Read/Convert Input. Power up and put the MAX1156/MAX1158/MAX1174 in acquisition mode by
holding R/C low during the ꢁirst ꢁalling edge oꢁ CS. During the second ꢁalling edge oꢁ CS, the level on
R/C determines whether the reꢁerence and reꢁerence buꢁꢁer power down or remain on aꢁter
conversion. Set R/C high during the second ꢁalling edge oꢁ CS to power down the reꢁerence and
buꢁꢁer, or set R/C low to leave the reꢁerence and buꢁꢁer powered up. Set R/C high during the third
ꢁalling edge oꢁ CS to put valid data on the bus.
5
R/C
6
7
EOC
End oꢁ Conversion. EOC drives low when conversion is complete.
Analog Supply Input. Bypass with a 0.1µF capacitor to AGND.
Analog Ground. Primary analog ground (star ground).
Analog Input
AV
DD
8
AGND
AIN
9
10
AGND
Analog Ground. Connect pin 10 to pin 8.
Reꢁerence Buꢁꢁer Output. Bypass REFADJ with a 0.1µF capacitor to AGND ꢁor internal reꢁerence
11
12
REFADJ
REF
mode. Connect REFADJ to AV
to select external reꢁerence mode.
DD
Reꢁerence Input/Output. Bypass REF with a 10µF capacitor to AGND ꢁor internal reꢁerence mode.
External reꢁerence input when in external reꢁerence mode.
6
_______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Pin Description (continued)
PIꢂ
ꢂAME
FUꢂCTIOꢂ
High-Byte Enable Input. Used to multiplex the 14-bit conversion result.
1: Most signiꢁicant byte available on the data bus.
13
HBEN
0: Least signiꢁicant byte available on the data bus.
Convert Start. The ꢁirst ꢁalling edge oꢁ CS powers up the device and enables acquire mode when R/C
is low. The second ꢁalling edge oꢁ CS starts conversion. The third ꢁalling edge oꢁ CS loads the result
onto the bus when R/C is high.
14
CS
15
16
17
18
19
20
DGND
Digital Ground
DV
Digital Supply Voltage. Bypass with a 0.1µF capacitor to DGND.
Three-State Digital Data Output. D0 is the LSB.
Three-State Digital Data Output
DD
D0/D8
D1/D9
D2/D10
D3/D11
Three-State Digital Data Output
Three-State Digital Data Output
Analog Input
DV
DD
Input Scaler
The MAX1156/MAX1158/MAX1174 have an input
scaler, which allows conversion oꢁ true bipolar input
voltages and input voltages greater than the power
supply, while operating ꢁrom a single +5V analog sup-
ply. The input scaler attenuates and shiꢁts the analog
input to match the input range oꢁ the internal DAC. The
MAX1156 has a unipolar input voltage range oꢁ 0 to
+10V. The MAX1158 input voltage range is 10V while
the MAX1174 input voltage range is 5V. Figure 4
shows the equivalent input circuit oꢁ the MAX1156/
MAX1158/MAX1174. This circuit limits the current going
into or out oꢁ AIN to less than 1.8mA.
1mA
DO–D13
DO–D13
C
= 20pF
C
= 20pF
LOAD
1mA
LOAD
DGND
DGND
a) HIGH-Z TO V
,
OH
b) HIGH-Z TO V ,
OL
V
V
TO V , AND
OL
OH
OH
V
OH
V
OL
TO V , AND
TO HIGH-Z
OL
TO HIGH-Z
Figure 1. Load Circuits
Track and Hold (T/H)
In track mode, the internal hold capacitor acquires the
analog signal (see Figure 4). In hold mode, the T/H
switches open and the capacitive DAC samples the
analog input. During the acquisition, the analog input
Detailed Description
Converter Operation
The MAX1156/MAX1158/MAX1174 use a successive-
approximation (SAR) conversion technique with an
inherent track-and-hold (T/H) stage to convert an ana-
log input into a 14-bit digital output. Parallel outputs
provide a high-speed interꢁace to microprocessors
(µPs). The Functional Diagram shows a simpliꢁied inter-
nal architecture oꢁ the MAX1156/MAX1158/MAX1174.
Figure 3 shows a typical application circuit ꢁor the
MAX1156/MAX1158/MAX1174.
(AIN) charges capacitor C
. The acquisition ends
HOLD
on the second ꢁalling edge oꢁ CS. At this instant, the
T/H switches open. The retained charge on C rep-
HOLD
resents a sample oꢁ the input. In hold mode, the capac-
itive DAC adjusts during the remainder oꢁ the
conversion time to restore node T/H OUT to zero within
the limits oꢁ 14-bit resolution. Force CS low to put valid
data on the bus aꢁter conversion is complete.
_______________________________________________________________________________________
7
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
t
t
CSH
CSL
CS
R/C
t
ACQ
REF POWER-
DOWN CONTROL
t
t
t
t
DV
EOC
DH
DS
EOC
t
t
DO
CONV
HBEN
t
t
t
DO1
BR
DO
HIGH-Z
HIGH-Z
D7/D15–D0/D8
HIGH/LOW
BYTE VALID
HIGH/LOW
BYTE VALID
Figure 2. MAX1156/MAX1158/MAX1174 Timing Diagram
Power-Down Modes
Select standby mode or shutdown mode with the R/C
bit during the second ꢁalling edge oꢁ CS (see the
Selecting Standby or Shutdown Mode section). The
MAX1156/MAX1158/MAX1174 automatically enter
either standby mode (reꢁerence and buꢁꢁer on) or shut-
down (reꢁerence and buꢁꢁer oꢁꢁ) aꢁter each conversion,
depending on the status oꢁ R/C during the second
ꢁalling edge oꢁ CS.
+5V ANALOG +5V DIGITAL
0.1µF
0.1µF
AV
DV
DD
DD
µP DATA
BUS
D0–D7
ANALOG INPUT
AIN
OR
Internal Clock
The MAX1156/MAX1158/MAX1174 generate an internal
conversion clock to ꢁree the microprocessor ꢁrom the
burden oꢁ running the SAR conversion clock. Total con-
D8–D13
MAX1156
MAX1158
MAX1174
EOC
R/C
CS
REF
version time (t
) aꢁter entering hold mode (second
CONV
REFADJ
ꢁalling edge oꢁ CS) to end oꢁ conversion (EOC) ꢁalling is
HBEN
4.7µs (max).
HIGH
BYTE
0.1µF
10µF
AGND DGND
Applications Information
LOW
BYTE
Starting a Conversion
CS and R/C control acquisition and conversion in the
MAX1156/MAX1158/MAX1174 (see Figure 2). The ꢁirst
ꢁalling edge oꢁ CS powers up the device and puts it in
acquire mode iꢁ R/C is low. The convert start is ignored
iꢁ R/C is high. The MAX1156/MAX1158/MAX1174 need
Figure 3. Typical Application Circuit for the MAX1156/MAX1158/
MAX1174
at least 12ms (C
= 0.1µF, C
= 10µF) ꢁor the
REF
REFADJ
internal reꢁerence to wake up and settle beꢁore starting
the conversion, iꢁ powering up ꢁrom shutdown.
8
_______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
REF
MAX1156
MAX1158/MAX1174
R1
3.4kΩ
R1
3.4kΩ
C
C
HOLD
30pF
HOLD
30pF
R2
161Ω
R2
161Ω
TRACK
S1
TRACK
S1
AIN
AIN
T/H OUT
T/H OUT
R3
R3
HOLD
HOLD
TRACK
HOLD
S2
TRACK
HOLD
S2
S3
POWER-
DOWN
R2 = 7.85kΩ (MAX1158)
OR 3.92kΩ (MAX1156/MAX1174)
S1, S2 = T/H SWITCH
S3 = POWER-DOWN
R3 = 5.45kΩ (MAX1158)
(MAX1158/MAX1174 ONLY)
OR 17.79kΩ (MAX1156/MAX1174)
Figure 4. Equivalent Input Circuit
Standby Mode
Selecting Standby or Shutdown Mode
The MAX1156/MAX1158/MAX1174 have a selectable
standby or low-power shutdown mode. In standby
mode, the ADC’s internal reꢁerence and reꢁerence
buꢁꢁer do not power down between conversions, elimi-
nating the need to wait ꢁor the reꢁerence to power up
beꢁore perꢁorming the next conversion. Shutdown mode
powers down the reꢁerence and reꢁerence buꢁꢁer aꢁter
completing a conversion. The reꢁerence and reꢁerence
While in standby mode, the supply current is less than
3.7mA (typ). The next ꢁalling edge oꢁ CS with R/C low
causes the MAX1156/MAX1158/MAX1174 to exit stand-
by mode and begin acquisition. The reꢁerence and reꢁ-
erence buꢁꢁer remain active to allow quick turn-on time.
Shutdown Mode
In shutdown mode, the reꢁerence and reꢁerence buꢁꢁer
are shut down between conversions. Shutdown mode
reduces supply current to 0.5µA (typ) immediately aꢁter
the conversion. The next ꢁalling edge oꢁ CS with R/C
low causes the reꢁerence and buꢁꢁer to wake up and
enter acquisition mode. To achieve 14-bit accuracy,
buꢁꢁer require a minimum oꢁ 12ms (C
= 0.1µF,
REFADJ
C
REF
= 10µF) to power up and settle ꢁrom shutdown.
The state oꢁ R/C at the second ꢁalling edge oꢁ CS
selects which power-down mode the MAX1156/
MAX1158/MAX1174 enter upon conversion completion.
Holding R/C low causes the MAX1156/MAX1158/
MAX1174 to enter standby mode. The reꢁerence and
buꢁꢁer are leꢁt on aꢁter the conversion completes. R/C
high causes the MAX1156/MAX1158/MAX1174 to enter
shutdown mode and power down the reꢁerence and
buꢁꢁer aꢁter conversion (see Figures 5 and 6). Set the
voltage at R/C high during the second ꢁalling edge oꢁ
CS to realize the lowest current operation.
allow 12ms (C
= 0.1µF, C
= 10µF) ꢁor the
REF
REFADJ
internal reꢁerence to wake up.
Internal and External Reference
Internal Reference
The internal reꢁerence oꢁ the MAX1156/MAX1158/
MAX1174 is internally buꢁꢁered to provide +4.096V out-
put at REF. Bypass REF to AGND and REFADJ to
AGND with 10µF and 0.1µF, respectively. Sink or
source current at REFADJ to make ꢁine adjustments to
the internal reꢁerence. The input impedance oꢁ REFADJ
is nominally 5kΩ. Use the circuit oꢁ Figure 7 to adjust
the internal reꢁerence to 1.5ꢀ.
_______________________________________________________________________________________
9
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
DATA
OUT
DATA
OUT
ACQUISITION
CONVERSION
ACQUISITION
CONVERSION
CS
CS
R/C
R/C
EOC
EOC
REF AND
BUFFER
POWER
REF AND
BUFFER
POWER
Figure 6. Selecting Shutdown Mode
Figure 5. Selecting Standby Mode
External Reference
HBEN toggles the output between the high/low byte.
The low byte is loaded onto the output bus when HBEN
is low and the high byte is on the bus when HBEN is
high. The two MSBs oꢁ the high byte are always zero.
An external reꢁerence can be placed at either the input
(REFADJ) or the output (REF) oꢁ the MAX1156/
MAX1158/MAX1174’s internal buꢁꢁer ampliꢁier. Using
the buꢁꢁered REFADJ input makes buꢁꢁering the exter-
nal reꢁerence unnecessary. The input impedance oꢁ
REFADJ is typically 5kΩ. The internal buꢁꢁer output
must be bypassed at REF with a 10µF capacitor.
Transfer Function
Figures 8, 9, and 10 show the MAX1156/MAX1158/
MAX1174 output transꢁer ꢁunctions. The MAX1158 and
MAX1174 outputs are coded in oꢁꢁset binary, while the
MAX1156 is coded in standard binary.
Connect REFADJ to AV
to disable the internal buꢁꢁer.
DD
Directly drive REF using an external 3.8V to 4.2V reꢁer-
ence. During conversion, the external reꢁerence must
be able to drive 100µA oꢁ DC load current and have an
output impedance oꢁ 10Ω or less.
Input Buffer
Most applications require an input buꢁꢁer ampliꢁier to
achieve 14-bit accuracy and prevent loading the
source. Switch the channels immediately aꢁter acquisi-
tion, rather than near the end oꢁ or aꢁter a conversion,
when the input signal is multiplexed. This allows more
time ꢁor the input buꢁꢁer ampliꢁier to respond to a large
step-change in input signal. The input ampliꢁier must
have a high enough slew rate to complete the required
output voltage change beꢁore the beginning oꢁ the
acquisition time. Figure 11 shows an example oꢁ this
circuit using the MAX427.
For optimal perꢁormance, buꢁꢁer the reꢁerence through
an op amp and bypass REF with a 10µF capacitor.
Consider the MAX1156/MAX1158/MAX1174’s equiva-
lent input noise (0.32LSB) when choosing a reꢁerence.
Reading the Conversion Result
EOC is provided to ꢁlag the microprocessor when a
conversion is complete. The ꢁalling edge oꢁ EOC sig-
nals that the data is valid and ready to be output to the
bus. D0–D13 are the parallel outputs oꢁ the
MAX1156/MAX1158/MAX1174. These three-state out-
puts allow ꢁor direct connection to a microcontroller I/O
bus. The outputs remain high-impedance during acqui-
sition and conversion. Data is loaded onto the output
bus with the third ꢁalling edge oꢁ CS with R/C high (aꢁter
Figures 12a and 12b show how the MAX1158 and
MAX1174 analog input current varies depending on
whether the chip is operating or powered down. The
part is ꢁully powered down between conversions iꢁ the
voltage at R/C is set high during the second ꢁalling
edge oꢁ CS. The input current abruptly steps to the
powered up value at the start oꢁ acquisition. This step
in the input current can disrupt the ADC input, depend-
ing on the driving circuit’s output impedance at high
ꢁrequencies. Iꢁ the driving circuit cannot ꢁully settle by
t
). Bringing CS high ꢁorces the output bus back to
DO
high impedance. The MAX1156/MAX1158/MAX1174
then wait ꢁor the next ꢁalling edge oꢁ CS to start the next
conversion cycle (see Figure 2).
±1 ______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
MAX1156
INPUT RANGE = 0 TO +10V
OUTPUT CODE
FULL-SCALE
TRANSITION
11 1111 1111 1111
11 1111 1111 1110
11 1111 1111 1101
MAX1156
MAX1158
MAX1174
+5V
68kΩ
100kΩ
REFADJ
FULL-SCALE RANGE
(FSR) = +10V
FSR x V
REF
0.1µF
1LSB =
150kΩ
00 0000 0000 0011
00 0000 0000 0010
00 0000 0000 0001
00 0000 0000 0000
16384 x 4.096
0
1
2
3
16383
16382 16384
INPUT VOLTAGE (LSB)
Figure 8. MAX1156 Transfer Function
Figure 7. MAX1156/MAX1158/MAX1174 Reference Adjust
Circuit
MAX1158
MAX1174
INPUT RANGE = -10V TO +10V
INPUT RANGE = -5V TO +5V
OUTPUT CODE
OUTPUT CODE
11 1111 1111 1111
FULL-SCALE
TRANSITION
FULL-SCALE
TRANSITION
11 1111 1111 1111
11 1111 1111 1110
11 1111 1111 1101
11 1111 1111 1110
11 1111 1111 1101
10 0000 0000 0001
10 0000 0000 0000
01 1111 1111 1111
10 0000 0000 0001
10 0000 0000 0000
01 1111 1111 1111
FULL-SCALE RANGE
(FSR) = +20V
FULL-SCALE RANGE
(FSR) = +10V
FSR x V
FSR x V
REF
REF
1LSB =
1LSB =
00 0000 0000 0011
00 0000 0000 0010
00 0000 0000 0001
00 0000 0000 0000
00 0000 0000 0011
00 0000 0000 0010
00 0000 0000 0001
00 0000 0000 0000
16384 x 4.096
16384 x 4.096
-8192 -8190
0
+8190 +8192
+8191
-8192 -8190
0
+8190 +8192
+8191
-8191 -8189
-1
+1
-8191 -8189
-1
+1
INPUT VOLTAGE (LSB)
INPUT VOLTAGE (LSB)
Figure 10. MAX1174 Transfer Function
Figure 9. MAX1158 Transfer Function
the end oꢁ acquisition, the accuracy oꢁ the system can
be compromised. To avoid this situation, increase the
acquisition time, use a driving circuit that can settle
ADC package. Use separate analog and digital ground
planes with only one point connecting the two ground
systems (analog and digital) as close to the device as
possible.
within t
, or leave the MAX1158/MAX1174 powered
ACQ
up by setting the voltage at R/C low during the second
ꢁalling edge oꢁ CS.
Route digital signals ꢁar away ꢁrom sensitive analog and
reꢁerence inputs. Iꢁ digital lines must cross analog lines,
do so at right angles to minimize coupling digital noise
onto the analog lines. Iꢁ the analog and digital sections
share the same supply, isolate the digital and analog
Layout, Grounding, and Bypassing
For best perꢁormance, use printed circuit boards. Do
not run analog and digital lines parallel to each other,
and do not layout digital signal paths underneath the
______________________________________________________________________________________ ±±
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
MAX1174
ANALOG INPUT CURRENT
vs. ANALOG INPUT VOLTAGE
REF
1.5
MAX1156
MAX1158
MAX1174
**
1.0
0.5
0
SHUTDOWN
MODE
ANALOG
INPUT
*
MAX427
AIN
-0.5
-1.0
-1.5
STANDBY
MODE
*MAX1156 ONLY.
**MAX1158/MAX1174 ONLY.
-5.0
-2.5
0
2.5
5.0
ANALOG INPUT VOLTAGE (V)
Figure 11. MAX1156/MAX1158/MAX1174 Fast-Settling Input
Buffer
Figure 12a. MAX1174 Analog Input Current
supply by connecting them with a low value (10Ω)
resistor or ꢁerrite bead.
MAX1158
ANALOG INPUT CURRENT
vs. ANALOG INPUT VOLTAGE
1.5
The ADC is sensitive to high-ꢁrequency noise on the
AV
supply. Bypass AV
to AGND with a 0.1µF
DD
DD
capacitor in parallel with a 1µF to 10µF low-ESR capacitor
with the smallest capacitor closest to the device. Keep
capacitor leads short to minimize stray inductance.
1.0
Definitions
0.5
0
SHUTDOWN
MODE
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation oꢁ the values
on an actual transꢁer ꢁunction ꢁrom a straight line. This
straight line can be either a best-straight-line ꢁit or a line
drawn between the endpoints oꢁ the transꢁer ꢁunction,
once oꢁꢁset and gain errors have been nulliꢁied. The
static linearity parameters ꢁor the MAX1156/MAX1158/
MAX1174 are measured using the endpoint method.
STANDBY
MODE
-0.5
-1.0
-1.5
-10
-5
0
5
10
ANALOG INPUT VOLTAGE (V)
Differential Nonlinearity
Diꢁꢁerential nonlinearity (DNL) is the diꢁꢁerence between
an actual step-width and the ideal value oꢁ 1LSB. A
DNL error speciꢁication oꢁ 1LSB guarantees no missing
codes and a monotonic transꢁer ꢁunction.
Figure 12b. MAX1158 Analog Input Current
±2 ______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
zation noise only. With an input range equal to the ꢁull-
scale range oꢁ the ADC, calculate the eꢁꢁective number
oꢁ bits as ꢁollows:
Signal-to-Noise Ratio
For a waveꢁorm perꢁectly reconstructed ꢁrom digital
samples, signal-to-noise ratio (SNR) is the ratio oꢁ the
ꢁull-scale analog input (RMS value) to the RMS quanti-
zation error (residual error). The ideal, theoretical mini-
mum analog-to-digital noise is caused by quantization
noise error only and results directly ꢁrom the ADC’s res-
olution (N bits):
SINAD−1.76
ENOB=
6.02
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio oꢁ the RMS
sum oꢁ the ꢁirst ꢁive harmonics oꢁ the input signal to the
ꢁundamental itselꢁ. This is expressed as:
SNR = (6.02 × N + 1.76) dB
where N = 14 bits.
In reality, there are other noise sources besides quanti-
zation noise; thermal noise, reꢁerence noise, clock jitter,
etc. SNR is computed by taking the ratio oꢁ the RMS
signal to the RMS noise, which includes all spectral
components minus the ꢁundamental, the ꢁirst ꢁive har-
monics, and the DC oꢁꢁset.
2
2
2
2
V
+ V + V + V
3 4 5
2
THD = 20 × log
V
1
where V is the ꢁundamental amplitude and V through
V are the 2nd- through 5th-order harmonics.
1
2
5
Signal-to-Noise Plus Distortion
Signal-to-noise plus distortion (SINAD) is the ratio oꢁ the
ꢁundamental input ꢁrequency’s RMS amplitude to the
RMS equivalent oꢁ all the other ADC output signals.
Spurious-Free Dynamic Range
Spurious-ꢁree dynamic range (SFDR) is the ratio oꢁ the
RMS amplitude oꢁ the ꢁundamental (maximum signal
component) to the RMS value oꢁ the next largest ꢁre-
quency component.
Signal
(Noise+Distortion)
RMS
SINAD(dB) = 20 × log
RMS
Effective Number of Bits
Eꢁꢁective number oꢁ bits (ENOB) indicates the global
accuracy oꢁ an ADC at a speciꢁic input ꢁrequency and
sampling rate. An ideal ADC’s error consists oꢁ quanti-
______________________________________________________________________________________ ±3
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Functional Diagram
REFADJ
HBEN
AV AGND DV DGND
DD
DD
5kΩ
REFERENCE
8 BITS
8 BITS
OUTPUT
REGISTERS
D0–D7
OR
D8–D13
REF
INPUT
SCALER
CAPACITIVE
DAC
AIN
MAX1156
MAX1158
MAX1174
AGND
SUCCESSIVE-
CLOCK
APPROXIMATION
REGISTER AND
CONTROL LOGIC
EOC
CS
R/C
Pin Configuration
Ordering Information (continued)
IꢂPUT
VOLTAGE
RAꢂGE
TOP VIEW
PIꢂ-
PACKAGE
PART
TEMP RAꢂGE
D4/D12
D5/D13
D6/0
1
2
20 D3/D11
19
18
D2/D10
D1/D9
MAX±±ꢁ8ACUP
0°C to +70°C
0°C to +70°C
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
20 TSSOP
10V
10V
10V
10V
5V
3
MAX1158BCUP
D7/0
4
17 D0/D8
16
MAX1158AEUP -40°C to +85°C
MAX1158BEUP -40°C to +85°C
MAX1156
MAX1158
MAX1174
5
R/C
DV
DD
EOC
6
15 DGND
MAX±±74ACUP
0°C to +70°C
0°C to +70°C
7
14
13
12
11
AV
DD
CS
MAX1174BCUP
5V
8
AGND
AIN
HBEN
REF
MAX1174AEUP -40°C to +85°C
MAX1174BEUP -40°C to +85°C
5V
9
5V
10
AGND
REFADJ
TSSOP
Chip Information
TRANSISTOR COUNT: 15,383
PROCESS: BiCMOS
±4 ______________________________________________________________________________________
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Package Information
(The package drawing(s) in this data sheet may not reꢁlect the most current speciꢁications. For the latest package outline inꢁormation,
go to www.(aꢄi(-ic.co(/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ ±ꢁ
© 2003 Maxim Integrated Products
Printed USA
is a registered trademark oꢁ Maxim Integrated Products.
相关型号:
MAX1158BCUP+T
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, 8 Bits Access, BICMOS, PDSO20, 4.40 MM, TSSOP-20
MAXIM
MAX1158BEUP-T
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, 8 Bits Access, BICMOS, PDSO20, 4.40 MM, TSSOP-20
MAXIM
MAX1159ACUI+
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, Word Access, BICMOS, PDSO28, 4.40 MM, TSSOP-28
MAXIM
MAX1159ACUI-T
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, Word Access, BICMOS, PDSO28, 4.40 MM, TSSOP-28
MAXIM
MAX1159AEUI+
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, Word Access, BICMOS, PDSO28, 4.40 MM, TSSOP-28
MAXIM
MAX1159AEUI-T
ADC, Successive Approximation, 14-Bit, 1 Func, 1 Channel, Parallel, Word Access, BICMOS, PDSO28, 4.40 MM, TSSOP-28
MAXIM
©2020 ICPDF网 联系我们和版权申明