MC9S08QB8CGK [ROCHESTER]
8-BIT, FLASH, 20MHz, MICROCONTROLLER, BCC24, 5 X 5 MM, 1 MM HEIGHT, 0.65 MM PITCH, ROHS COMPLIANT, MO-220VHHC-1, QFN-24;型号: | MC9S08QB8CGK |
厂家: | Rochester Electronics |
描述: | 8-BIT, FLASH, 20MHz, MICROCONTROLLER, BCC24, 5 X 5 MM, 1 MM HEIGHT, 0.65 MM PITCH, ROHS COMPLIANT, MO-220VHHC-1, QFN-24 时钟 微控制器 外围集成电路 |
文件: | 总37页 (文件大小:1987K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Freescale Semiconductor
Data Sheet: Technical Data
An Energy Efficient Solution by Freescale
Document Number: MC9S08QB8
Rev. 3, 3/2009
MC9S08QB8
28 SOIC
16-Pin TSSOP
Case 948F
Case 751F
MC9S08QB8 Series
Covers: MC9S08QB8 and
MC9S08QB4
24 QFN
Case 1982-01
Features
• Development Support
– Single-wire background debug interface
– Breakpoint capability to allow single breakpoint setting
during in-circuit debugging
• 8-Bit HCS08 Central Processor Unit (CPU)
– Up to 20 MHz CPU at 3.6 V to 1.8 V across temperature
range of –40 °C to 85 °C
– HC08 instruction set with added BGND instruction
– Support for up to 32 interrupt/reset sources
• On-Chip Memory
• Peripherals
– ADC — 8-channel, 12-bit resolution; 2.5 μs conversion
time; automatic compare function; 1.7 mV/°C
temperature sensor; internal bandgap reference channel;
operation in stop3; fully functional from 3.6 V to 1.8 V.
– ACMP — Analog comparator with selectable interrupt
on rising, falling, or either edge of comparator output;
compare option to fixed internal bandgap reference
voltage; output can be tied internally to TPM input
capture; operation in stop3
– Up to 8 KB flash memory read/program/erase over full
operating voltage and temperature
– Up to 512 bytes random-access memory (RAM)
– Security circuitry to prevent unauthorized access to
RAM and flash contents
• Power-Saving Modes
– Two very low power stop modes
– TPM — One 1-channel timer/pulse-width modulator
(TPM) module; selectable input capture, output
compare, or buffered edge- or center-aligned PWM on
each channel; ACMP output can be tied internally to
input capture
– Peripheral clock enable register can disable clocks to
unused modules, thereby reducing currents
– Low power run
– Low power wait
– 6 μs typical wakeup time from stop3 mode
– Typical stop current of 250 nA at 3 V, 25 °C
• Clock Source Options
– MTIM — 8-bit modulo timer module with optional
prescaler
– RTC — (Real-time counter) 8-bit modulo counter with
binary or decimal based prescaler; external clock source
for precise time base, time-of-day, calendar or task
scheduling functions; free running on-chip low power
oscillator (1 kHz) for cyclic wakeup without external
components; runs in all MCU modes
– SCI — Full duplex non-return to zero (NRZ); LIN
master extended break generation; LIN slave extended
break detection; wakeup on active edge
– Oscillator (XOSC) — Very low-power, loop-control
Pierce oscillator; crystal or ceramic resonator range of
31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz
– Internal Clock Source (ICS) — Internal clock source
module containing a frequency-locked-loop (FLL)
controlled by internal reference; precision trimming of
internal reference allows 0.2% resolution and 2%
deviation over temperature and voltage; supports bus
frequencies from 1 MHz to 10 MHz
– KBI — 8-pin keyboard interrupt with selectable edge
and level detection modes
• Input/Output
• System Protection
– Watchdog computer operating properly (COP) reset
with option to run from dedicated 1 kHz internal clock
source or bus clock
– Low-voltage detection with reset or interrupt; selectable
trip points
– Illegal opcode detection with reset
– Illegal address detection with reset
– Flash block protection
– 22 GPIOs and one input-only and one output-only pin.
– Hysteresis and configurable pullup device on all input
pins; configurable slew rate and drive strength on all
output pins except PTA5.
• Package Options
– 28-pin SOIC, 24-pin QFN, 16-pin TSSOP
This document contains information on a product under development. Freescale reserves the
right to change or discontinue this product without notice.
© Freescale Semiconductor, Inc., 2008-2009. All rights reserved.
Table of Contents
1
2
3
MCU Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.11 Analog Comparator (ACMP) Electricals . . . . . . .20
3.12 ADC Characteristics . . . . . . . . . . . . . . . . . . . . . .20
3.13 Flash Specifications . . . . . . . . . . . . . . . . . . . . . .23
3.14 EMC Performance . . . . . . . . . . . . . . . . . . . . . . .24
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . .25
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . .25
5.1 Mechanical Drawings . . . . . . . . . . . . . . . . . . . . .25
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Parameter Classification . . . . . . . . . . . . . . . . . . . 7
3.3 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 7
3.4 Thermal Characteristics. . . . . . . . . . . . . . . . . . . . 8
3.5 ESD Protection and Latch-Up Immunity . . . . . . . 9
3.6 DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . 10
3.7 Supply Current Characteristics . . . . . . . . . . . . . 13
3.8 External Oscillator (XOSC) Characteristics. . . . 15
3.9 Internal Clock Source (ICS) Characteristics . . . 16
3.10 AC Characteristics. . . . . . . . . . . . . . . . . . . . . . . 18
3.10.1Control Timing. . . . . . . . . . . . . . . . . . . . . 18
3.10.2TPM Module Timing . . . . . . . . . . . . . . . . 19
4
5
Revision History
To provide the most up-to-date information, the revision of our documents on the World Wide Web will
be the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://freescale.com/
The following revision history table summarizes changes contained in this document.
Rev
Date
Description of Changes
1
2
3
10/22/2008
12/17/2008
3/6/2009
Initial public released.
Completed all the TBDs in Table 8.
Corrected the 24-pin QFN package information.
Changed VDDAD and VSSAD to VDDA and VSSA separatedly.
In Table 7, updated the |IIn|, |IOZ| and added |IOZTOT|.
In Table 11, updated the DCO output frequency range-trimmed, and updated some of the
symbols.
Related Documentation
Find the most current versions of all documents at: http://www.freescale.com
Reference Manual (MC9S08QB8RM)
Contains extensive product information including modes of operation, memory,
resets and interrupts, register definition, port pins, CPU, and all module
information.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
2
Freescale Semiconductor
MCU Block Diagram
1
MCU Block Diagram
The block diagram shows the structure of the MC9S08QB8 MCU.
PTA7
PTA6
HCS08 CORE
PTA5/IRQ/TCLK/RESET
PTA4/ACMPO/BKGD/MS
PTA3/KBIP3/ADP3
BDC
CPU
ANALOG COMPARATOR
(ACMP)
PTA2/KBIP2/ADP2
HCS08 SYSTEM CONTROL
PTA1/KBIP1/ADP1/ACMP–
PTA0/KBIP0/TPMCH0/ADP0/ACMP+
VREFL/VSSA
VREFH/VDDA
12-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC)
RESETS AND INTERRUPTS
MODES OF OPERATION
POWER MANAGEMENT
PTB7/EXTAL
PTB6/XTAL
COP
IRQ
LVD
8-BIT MODULO TIMER
MODULE (MTIM)
PTB5/TPMCH0
PTB4
PTB3/KBIP7/ADP7
PTB2/KBIP6/ADP6
PTB1/KBIP5/TxD/ADP5
PTB0/KBIP4/RxD/ADP4
REAL-TIME COUNTER
(RTC)
USER FLASH
(MC9S08QB8 = 8192 BYTES)
(MC9S08QB4 = 4096 BYTES)
16-BIT TIMER/PWM
MODULE (TPM)
USER RAM
(MC9S08QB8 = 512 BYTES)
(MC9S08QB4 = 256 BYTES)
PTC7
PTC6
PTC5
PTC4
PTC3
PTC2
PTC1
PTC0
SERIAL COMMUNICATIONS
INTERFACE MODULE (SCI)
KEYBOARD INTERRUPT
(KBI)
20 MHz INTERNAL CLOCK
SOURCE (ICS)
LOW-POWER OSCILLATOR
31.25 kHz to 38.4 kHz
1 MHz to 16 MHz
(XOSC)
VSS
VDD
VOLTAGE REGULATOR
pins not available on 24-pin or 16-pin packages
pins not available on 16-pin package
1
VDDA/VREFH and VSSA/VREFL are double bonded to VDD and VSS respectively in16-pin package.
Figure 1. MC9S08QB8 Series Block Diagram
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
3
Pin Assignments
2
Pin Assignments
This chapter shows the pin assignments for the MC9S08QB8 series devices.
Table 1. Pin Availability by Package Pin-Count
Pin Number
<-- Lowest Priority --> Highest
28
24
16
Port Pin
Alt 1
Alt 2
Alt 3
Alt 4
1
—
—
23
24
1
—
—
1
PTC5
PTC4
PTA5
PTA4
2
3
IRQ
TCLK
RESET
MS
4
2
ACMPO
BKGD
5
3
VDD
6
2
—
—
4
VDDA/VREFH
VSSA/VREFL
VSS
7
3
8
4
9
5
5
PTB7
PTB6
PTB5
PTB4
PTC3
PTC2
PTC1
PTC0
PTB3
EXTAL
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
6
6
XTAL
7
7
TPMCH01
8
8
—
—
9
—
—
—
—
9
10
11
12
13
14
15
16
17
18
19
20
21
22
KBIP7
KBIP6
KBIP5
KBIP4
ADP7
ADP6
ADP5
ADP4
10 PTB2
11 PTB1
12 PTB0
TxD
RxD
—
—
PTA7
PTA6
13 PTA3
14 PTA2
15 PTA1
16 PTA0
KBIP3
KBIP2
KBIP1
KBIP0
ADP3
ADP2
ADP12
ACMP–2
ACMP+2
TPMCH0 ADP02
—
—
PTC7
PTC6
1
2
TPMCH0 pin can be repositioned using at PTB5 TPMCH0PS in SOPT2, default
reset location is PTA0.
If ADC and ACMP are enabled, both modules will have access to the pin.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
4
Freescale Semiconductor
Pin Assignments
PTC6
PTC7
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
PTC5
PTC4
2
PTA5/IRQ/TCLK/RESET
PTA4/ACMPO/BKGD/MS
VDD
3
PTA0/KBIP0/TPMCH0/ADP0/ACMP+
PTA1/KBIP1/ADP1/ACMP–
PTA2/KBIP2/ADP2
4
5
V
DDA/VREFH
VSSA/VREFL
VSS
6
PTA3/KBIP3/ADP3
PTA6
7
8
PTA7
PTB7/EXTAL
PTB6/XTAL
PTB5/TPMCH0
PTB4
9
PTB0/KBIP4/RxD/ADP4
10
11
12
13
14
PTB1/KBIP5/TxD/ADP5
PTB2/KBIP6/ADP6
PTB3/KBIP7/ADP7
PTC0
PTC3
PTC2
PTC1
Pins shown in bold type are lost in the next lower pin count package.
Figure 2. MC9S08QB8 Series in 28-Pin SOIC Package
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
5
Pin Assignments
24 23 22 21 20 19
PTA2/KBIP2/ADP2
PTA3/KBIP3/ADP3
PTA6
18
17
16
VDD
1
2
3
4
5
6
VDDA/VREFH
VSSA/VREFL
VSS
15 PTA7
PTB7/EXTAL
PTB6/XTAL
14
13
PTB0/KBIP4/RxD/ADP4
PTB1/KBIP5/TxD/ADP5
7
8
9
10 11 12
Pins shown in bold type are lost in the next lower pin count package.
Figure 3. MC9S08QB8 Series in 24-Pin QFN Packages
16
15
14
13
PTA0/KBIP0/TPMCH0/ADP0/ACMP+
PTA1/KBIP1/ADP1/ACMP–
PTA2/KBIP2/ADP2
1
2
3
4
5
6
7
8
PTA5/IRQ/TCLK/RESET
PTA4/ACMPO/BKGD/MS
VDD
PTA3/KBIP3/ADP3
VSS
12
11
PTB0/KBIP4/RxD/ADP4
PTB1/KBIP5/TxD/ADP5
PTB2/KBIP6/ADP6
PTB7/EXTAL
PTB6/XTAL
PTB5/TPMCH0
PTB4
10
9
PTB3/KBIP7/ADP7
Figure 4. MC9S08QB8 Series in 16-Pin TSSOP Package
MC9S08QB8 Series MCU Data Sheet, Rev. 3
6
Freescale Semiconductor
Electrical Characteristics
3
Electrical Characteristics
3.1
Introduction
This chapter contains electrical and timing specifications for the MC9S08QB8 series of microcontrollers
available at the time of publication.
3.2
Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the
customer a better understanding the following classification is used and the parameters are tagged
accordingly in the tables where appropriate:
Table 2. Parameter Classifications
Those parameters are guaranteed during production testing on each individual device.
P
C
Those parameters are achieved by the design characterization by measuring a statistically relevant
sample size across process variations.
Those parameters are achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted. All values shown in the typical column are within this
category.
T
Those parameters are derived mainly from simulations.
D
NOTE
The classification is shown in the column labeled “C” in the parameter
tables where appropriate.
3.3
Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not
guaranteed. Stress beyond the limits specified in Table 3 may affect device reliability or cause permanent
damage to the device. For functional operating conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (for instance, either V or V ) or the programmable
SS
DD
pull-up resistor associated with the pin is enabled.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
7
Electrical Characteristics
Table 3. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
IDD
VIn
–0.3 to 3.8
120
V
mA
V
Maximum current into VDD
Digital input voltage
–0.3 to VDD + 0.3
Instantaneous maximum current
ID
±25
mA
Single pin limit (applies to all port pins)1, 2, 3
Storage temperature range
Tstg
–55 to 150
°C
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2
3
All functional non-supply pins, except for PTA5 are internally clamped to VSS and VDD
.
Power supply must maintain regulation within operating VDD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
3.4
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and voltage regulator circuits, and it is user-determined rather than being controlled by the
MCU design. To take P into account in power calculations, determine the difference between actual pin
I/O
voltage and V or V and multiply by the pin current for each I/O pin. Except in cases of unusually high
SS
DD
pin current (heavy loads), the difference between pin voltage and V or V will be very small.
SS
Table 4. Thermal Characteristics
DD
Rating
Symbol
Value
Unit
TL to TH
–40 to 85
Operating temperature range (packaged)
TA
°C
Maximum junction temperature
Thermal resistance 28-pin SOIC
Thermal resistance 24-pin QFN
Thermal resistance 16-pin TSSOP
TJM
95
70
°C
°C/W
°C/W
°C/W
θJA
92
129
The average chip-junction temperature (T ) in °C can be obtained from:
J
T = T + (P × θ )
JA
Eqn. 1
J
A
D
where:
MC9S08QB8 Series MCU Data Sheet, Rev. 3
8
Freescale Semiconductor
Electrical Characteristics
T = Ambient temperature, °C
A
θ
= Package thermal resistance, junction-to-ambient, °C/W
JA
P = P + P
D
int
I/O
P
P
= I × V , Watts — chip internal power
int
I/O
DD DD
= Power dissipation on input and output pins — user determined
For most applications, P << P and can be neglected. An approximate relationship between P and T
I/O
int
D
J
(if P is neglected) is:
I/O
P = K ÷ (T + 273°C)
Eqn. 2
D
J
Solving Equation 1 and Equation 2 for K gives:
2
K = P × (T + 273°C) + θ × (P )
Eqn. 3
D
A
JA
D
where K is a constant pertaining to the particular part. K can be determined from equation 3 by measuring
P (at equilibrium) for a known T . Using this value of K, the values of P and T can be obtained by
D
A
D
J
solving Equation 1 and Equation 2 iteratively for any value of T .
A
3.5
ESD Protection and Latch-Up Immunity
Although damage from electrostatic discharge (ESD) is much less common on these devices than on early
CMOS circuits, normal handling precautions should be taken to avoid exposure to static discharge.
Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels
of static without suffering any permanent damage.
All ESD testing is in conformity with AEC-Q100 Stress Test Qualification for Automotive Grade
Integrated Circuits. During the device qualification, ESD stresses were performed for the human body
model (HBM), the machine model (MM) and the charge device model (CDM).
A device is defined as a failure if after exposure to ESD pulses the device no longer meets the device
specification. Complete DC parametric and functional testing is performed per the applicable device
specification at room temperature followed by hot temperature, unless instructed otherwise in the device
specification.
Table 5. ESD and Latch-up Test Conditions
Model
Description
Series resistance
Symbol
Value
1500
100
3
Unit
Ω
R1
C
Human
Body
Storage capacitance
Number of pulses per pin
Series resistance
pF
—
R1
C
0
Ω
Machine Storage capacitance
Number of pulses per pin
200
3
pF
—
Minimum input voltage limit
Latch-up
–2.5
7.5
V
V
Maximum input voltage limit
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
9
Electrical Characteristics
No.
Table 6. ESD and Latch-Up Protection Characteristics
Rating1
Symbol
Min
Max
Unit
1
2
Human body model (HBM)
Charge device model (CDM)
Latch-up current at TA = 85°C
VHBM
VCDM
ILAT
±2000
±500
±100
—
—
—
V
V
3
mA
1
Parameter is achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted.
3.6
DC Characteristics
This section includes information about power supply requirements and I/O pin characteristics.
Table 7. DC Characteristics
Num
C
Characteristic
Symbol
Condition
Min
Typical1
Max
Unit
1
P Operating Voltage
C
VDD
—
1.8
—
3.6
V
All I/O pins,
low-drive strength
VDD > 1.8 V,
ILoad = –2 mA
VDD – 0.5
VDD – 0.5
—
—
—
—
—
—
—
—
—
—
Output high
voltage
VDD > 2.7 V,
ILoad = –10 mA
2
P
VOH
V
mA
V
All I/O pins,
high-drive strength
V
DD > 1.8V,
ILoad = –2 mA
C
V
DD – 0.5
—
Output high
current
D
C
P
C
D
Max total IOH for all ports IOHT
VOUT < VDD
0
–80
0.5
0.5
0.5
80
3
4
All I/O pins,
low-drive strength
VDD > 1.8 V,
ILoad = 0.6 mA
—
—
—
0
Output low
voltage
VDD > 2.7 V,
ILoad = 10 mA
VOL
All I/O pins,
high-drive strength
VDD > 1.8 V,
ILoad = 3 mA
5
6
Output low
current
Max total IOL for all ports
all digital inputs
IOLT
VIH
VOUT > VSS
mA
V
P
C
P
C
VDD > 2.7 V
VDD > 1.8 V
VDD > 2.7 V
VDD > 1.8 V
0.70 x VDD
—
—
—
—
—
Input high
voltage
0.85 x VDD
—
—
—
0.35 x VDD
0.30 x VDD
Input low
voltage
7
8
all digital inputs
VIL
Input
hysteresis
C
all digital inputs Vhys
—
0.06 x VDD
—
—
mV
nA
Input
P leakage
current
all input only pins
|IIn|
9
VIn = VDD or VSS
—
—
200
(Per pin)
Hi-Z
(off-state)
leakage
all input/output
10
P
|IOZ
|
VIn = VDD or VSS
—
—
200
nA
(per pin)
current
MC9S08QB8 Series MCU Data Sheet, Rev. 3
10
Freescale Semiconductor
Electrical Characteristics
Table 7. DC Characteristics (continued)
Num
C
Characteristic
Symbol
Condition
Min
Typical1
Max
Unit
Total
leakage
combined
for all inputs
and Hi-Z
pins
10
C
All input only and I/O |IOZTOT
|
VIn = VDD or VSS
—
—
2
μA
Pullup,
11 P Pulldown
resistors
all digital inputs except
PTA5/IRQ/TCLK/RESET,
when enabled
RPU,
RPD
—
—
17.5
17.5
—
—
52.5
52.5
kΩ
kΩ
Pullup,
12 C Pulldown
resistors
PTA5/IRQ/TCLK/RESET, RPU,
when enabled2
RPD
Single pin limit
–0.2
–5
—
—
0.2
5
mA
mA
DCinjection
13 D current 3, 4,
IIC
VIN < VSS, VIN > VDD
Total MCU limit, includes
sum of all stressed pins
5
14 C Input Capacitance, all pins
15 C RAM retention voltage
16 C POR re-arm voltage6
17 D POR re-arm time
CIn
—
—
—
—
—
—
—
0.6
1.4
—
8
pF
V
VRAM
VPOR
tPOR
1.0
2.0
—
0.9
10
V
μs
VDD falling
VDD rising
1.80
1.88
1.84
1.92
1.88
1.96
18 P Low-voltage detection threshold
VLVD
VLVW
V
V
VDD falling
VDD rising
19 P Low-voltage warning threshold
Low-voltage inhibit reset/recover
2.08
2.14
2.26
20
C
Vhys
VBG
—
—
—
80
—
mV
V
hysteresis
21 P Bandgap Voltage Reference7
1.15
1.17
1.18
1
2
Typical values are measured at 25 °C. Characterized, not tested
The specified resistor value is the actual value internal to the device. The pullup or pulldown value may appear lower when
measured externally on the pin.
3
4
All functional non-supply pins, except for PTA5 are internally clamped to VSS and VDD
.
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
5
Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current
conditions. If the positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could
result in external power supply going out of regulation. Ensure that external VDD load will shunt current greater than maximum
injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is
present, or if clock rate is very low (which would reduce overall power consumption).
6
7
Maximum is highest voltage that POR is guaranteed.
Factory trimmed at VDD = 3.0 V, Temp = 25 °C
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
11
Electrical Characteristics
PULLUP RESISTOR TYPICALS
40
35
30
25
20
PULLDOWN RESISTOR TYPICALS
85°C
40
35
30
25
20
85°C
25°C
25°C
–40°C
–40°C
1.8
2
2.2 2.4 2.6 2.8
3
3.2 3.4 3.6
1.8
2.3
2.8
VDD (V)
3.3
3.6
VDD (V)
Figure 5. Pullup and Pulldown Typical Resistor Values (V = 3.0 V)
DD
TYPICAL VOL VS IOL AT VDD = 3.0 V
TYPICAL VOL VS VDD
0.2
0.15
0.1
1.2
85°C
25°C
1
–40°C
0.8
0.6
0.4
0.2
0
85
25
–40
°
C, IOL = 2 mA
0.05
0
°
C, IOL = 2 mA
°
C, IOL = 2 mA
1
2
3
4
0
5
10
OL (mA)
15
20
VDD (V)
I
Figure 6. Typical Low-Side Driver (Sink) Characteristics — Low Drive (PTxDSn = 0)
TYPICAL VOL VS VDD
TYPICAL VOL VS IOL AT VDD = 3.0 V
1
0.4
0.3
0.2
0.1
85°C
85°C
25°C
–40°C
25°C
0.8
0.6
0.4
0.2
–40°C
IOL = 10 mA
IOL = 6 mA
IOL = 3 mA
0
0
0
10
20
30
1
2
3
4
VDD (V)
IOL (mA)
Figure 7. Typical Low-Side Driver (Sink) Characteristics — High Drive (PTxDSn = 1)
MC9S08QB8 Series MCU Data Sheet, Rev. 3
12
Freescale Semiconductor
Electrical Characteristics
TYPICAL VDD – VOH VS IOH AT VDD = 3.0 V
TYPICAL VDD – VOH VS VDD AT SPEC IOH
85 C, IOH = 2 mA
1.2
1
0.25
0.2
85°C
°
25°C
25 C, IOH = 2 mA
°
–40°C
–40 C, IOH = 2 mA
°
0.8
0.6
0.4
0.2
0
0.15
0.1
0.05
0
0
–5
–10
OH (mA))
–15
–20
1
2
3
4
VDD (V)
I
Figure 8. Typical High-Side (Source) Characteristics — Low Drive (PTxDSn = 0)
TYPICAL VDD – VOH VS VDD AT SPEC IOH
0.4
85°C
25°C
–40°C
TYPICAL V – V VS I AT V = 3.0 V
DD
OH
OH
DD
0.3
0.2
0.1
0.8
0.6
0.4
0.2
0
85°C
25°C
–40°C
IOH = –10 mA
IOH = –6 mA
I
OH = –3 mA
0
0
–5
–10
–15
–20
–25
–30
1
2
3
4
I
(mA)
OH
VDD (V)
Figure 9. Typical High-Side (Source) Characteristics — High Drive (PTxDSn = 1)
3.7
Supply Current Characteristics
This section includes information about power supply current in various operating modes.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
13
Electrical Characteristics
Table 8. Supply Current Characteristics
Parameter
Run supply current
VDD
(V)
Bus
Temp
Typical1
Num
C
Symbol
Max
Unit
Freq
(°C)
P
T
T
T
10 MHz
1 MHz
10 MHz
1 MHz
5.60
0.80
3.60
0.75
165
6
1
RIDD
mA
–40 to 85°C
–40 to 85°C
FEI mode, all modules on
3
3
—
—
—
Run supply current
FEI mode, all modules off
2
3
RIDD
mA
Run supply current
LPRS=0, all modules off
16 kHz
FBILP
T
T
T
—
—
—
RIDD
3
μA
–40 to 85°C
–40 to 85°C
16 kHz
FBELP
105
7.3
Run supply current
LPRS=1, all modules off
16 kHz
FBELP
RIDD
WIDD
WIDD
4
5
6
3
3
μA
μA
μA
T
T
Wait mode supply current
FEI mode, all modules off
10 MHz
1 MHz
570
290
1
—
—
–40 to 85°C
–40 to 85°C
Wait mode supply current
LPRS = 1, all mods off
16 kHz
FBELP
3
3
T
—
P
C
P
C
C
C
P
C
P
C
C
C
—
—
—
—
—
—
—
—
—
—
—
—
0.25
0.5
1
0.65
0.8
2
–40 to 25°C
70°C
85°C
7
Stop2 mode supply current
S2IDD
μA
μA
0.2
0.3
0.7
0.45
1
0.5
0.6
1.6
0.80
1.8
5.8
0.6
1.5
5.0
–40 to 25°C
70°C
2
3
2
85°C
–40 to 25°C
70°C
3
85°C
Stop3 mode supply current
no clocks active
8
S3IDD
0.3
0.8
2.5
–40 to 25°C
70°C
85°C
1
Data in Typical column was characterized at 3.0 V, 25 °C or is typical recommended value.
Table 9. Stop Mode Adders
Temperature
Num
C
Parameter
Condition
Units
–40°C
25°C
70°C
85°C
1
2
3
T
T
T
LPO
—
50
1000
63
75
1000
70
100
1100
77
150
1500
81
nA
nA
μA
ERREFSTEN
IREFSTEN1
RANGE = HGO = 0
—
MC9S08QB8 Series MCU Data Sheet, Rev. 3
14
Freescale Semiconductor
Electrical Characteristics
Table 9. Stop Mode Adders (continued)
Condition
Temperature
25°C 70°C
Num
C
Parameter
Units
–40°C
85°C
4
T
RTC
Does not include clock source
current
50
75
100
150
nA
5
6
7
T
T
T
LVD1
LVDSE = 1
90
18
95
100
20
110
22
115
23
μA
μA
μA
ACMP1
ADC1
Not using the bandgap (BGBE = 0)
ADLPC = ADLSMP = 1
106
114
120
Not using the bandgap (BGBE = 0)
1
Not available in stop2 mode.
3.8
External Oscillator (XOSC) Characteristics
Reference Figure 10 and Figure 11 for crystal or resonator circuits.
Table 10. XOSCVLP and ICS Specifications (Temperature Range = –40 to 85°C Ambient)
Num
C
Characteristic
Symbol
Min
Typ1
Max
Unit
Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1)
Low range (RANGE = 0)
High range (RANGE = 1), high gain (HGO = 1)
High range (RANGE = 1), low power (HGO = 0)
flo
fhi
fhi
32
1
1
—
—
—
38.4
16
8
kHz
MHz
MHz
1
C
Load capacitors
Low range (RANGE=0), low power (HGO=0)
Other oscillator settings
See Note 2
See Note 3
C1,C2
2
3
D
D
Feedback resistor
Low range, low power (RANGE = 0, HGO = 0)2
Low range, high gain (RANGE = 0, HGO = 1)
High range (RANGE = 1, HGO = X)
—
—
—
—
10
1
—
—
—
RF
MΩ
kΩ
Series resistor —
Low range, low power (RANGE = 0, HGO = 0)2
—
—
—
—
100
0
—
—
—
Low range, high gain (RANGE = 0, HGO = 1)
High range, low power (RANGE = 1, HGO = 0)
High range, high gain (RANGE = 1, HGO = 1)
RS
4
D
≥ 8 MHz
4 MHz
1 MHz
—
—
—
0
0
0
0
10
20
Crystal start-up time 4
Low range, low power
Low range, high gain
High range, low power
High range, high gain
t
—
—
—
—
600
400
5
—
—
—
—
CSTL
5
6
C
D
ms
t
CSTH
15
Square wave input clock frequency (EREFS = 0, ERCLKEN = 1)
FEE mode
fextal
0.03125
0
—
—
20
20
MHz
FBE or FBELP mode
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
15
Electrical Characteristics
1
Data in Typical column was characterized at 3.0 V, 25 °C or is typical recommended value.
Load capacitors (C1,C2), feedback resistor (RF) and series resistor (RS) are incorporated internally when RANGE = HGO = 0.
2
3
See crystal or resonator manufacturer’s recommendation.
4
Proper PC board layout procedures must be followed to achieve specifications.
XOSCVLP
EXTAL
XTAL
RS
RF
Crystal or Resonator
C1
C2
Figure 10. Typical Crystal or Resonator Circuit: High Range and Low Range/High Gain
XOSCVLP
EXTAL
XTAL
Crystal or Resonator
Figure 11. Typical Crystal or Resonator Circuit: Low Range/Low Power
3.9
Internal Clock Source (ICS) Characteristics
Table 11. ICS Frequency Specifications (Temperature Range = –40 to 85°C Ambient)
Num
C
Characteristic
Symbol
Min.
Typical1
Max.
Unit
Average internal reference frequency — factory trimmed
at VDD = 3.6 V and temperature = 25 °C
fint_t
1
P
—
32.768
—
kHz
Internal reference frequency — user trimmed
Internal reference start-up time
fint_ut
tIRST
2
3
P
T
31.25
—
—
60
—
39.06
100
kHz
μs
DCO output frequency range — Low range (DRS = 00)
trimmed2
16
fdco_t
20
—
4
5
6
P
P
C
MHz
MHz
%fdco
DCO output frequency2
Reference = 32768 Hz and DMX32 = 1
fdco_DMX32
—
19.92
Resolution of trimmed DCO output frequency at fixed voltage
and temperature (using FTRIM)
Δfdco_res_t
—
±0.1
±0.2
MC9S08QB8 Series MCU Data Sheet, Rev. 3
16
Freescale Semiconductor
Electrical Characteristics
Table 11. ICS Frequency Specifications (Temperature Range = –40 to 85°C Ambient) (continued)
Num
C
Characteristic
Symbol
Min.
Typical1
Max.
Unit
Resolution of trimmed DCO output frequency at fixed voltage
and temperature (not using FTRIM)
Δfdco_res_t
%fdco
7
C
—
± 0.2
± 0.4
Total deviation of DCO output from trimmed frequency3
Over full voltage and temperature range
Over fixed voltage and temperature range of 0 to 70 °C
Δfdco_t
%fdco
8
C
—
–1.0 to 0.5
± 2
± 1
±0.5
FLL acquisition time4
tAcquire
CJitter
10
11
C
C
—
—
—
1
ms
Long term jitter of DCO output clock (averaged over 2-ms
interval)5
%fdco
0.02
0.2
1
2
3
4
Data in Typical column was characterized at 3.0 V, 25 °C or is typical recommended value.
The resulting bus clock frequency should not exceed the maximum specified bus clock frequency of the device.
This parameter is characterized and not tested on each device.
This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing
from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference,
this specification assumes it is already running.
5
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBus
.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for
a given interval.
1.00%
0.50%
0.00%
-60
-40
-20
0
20
40
60
80
100
120
-0.50%
-1.00%
-1.50%
-2.00%
Temperature
Figure 12. Deviation of DCO Output from Trimmed Frequency (20 MHz, 3.0 V)
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
17
Electrical Characteristics
3.10 AC Characteristics
This section describes timing characteristics for each peripheral system.
3.10.1 Control Timing
Table 12. Control Timing
Num
C
D
D
D
D
Rating
Symbol
fBus
Min
Typical1
Max
10
Unit
MHz
μs
Bus frequency (tcyc = 1/fBus
)
1
2
3
4
DC
700
—
—
—
—
tLPO
Internal low power oscillator period
1300
—
External reset pulse width2
Reset low drive
textrst
trstdrv
100
ns
34 x tcyc
—
ns
BKGD/MS setup time after issuing background
debug force reset to enter user or BDM modes
tMSSU
tMSH
5
6
D
D
500
100
—
—
—
—
ns
BKGD/MS hold time after issuing background debug
force reset to enter user or BDM modes 3
μs
IRQ pulse width
7
D
Asynchronous path2
Synchronous path4
t
ILIH, tIHIL
100
1.5 x tcyc
—
—
—
—
ns
ns
8
D
Keyboard interrupt pulse width
Asynchronous path2
tILIH, IHIL
t
100
1.5 x tcyc
—
—
—
—
Synchronous path4
Port rise and fall time —
Low output drive (PTxDS = 0) (load = 50 pF)5
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
t
Rise, tFall
ns
—
—
16
23
—
—
9
D
Port rise and fall time —
High output drive (PTxDS = 1) (load = 50 pF)5
Slew rate control disabled (PTxSE = 0)
Slew rate control enabled (PTxSE = 1)
tRise, tFall
ns
—
—
5
9
—
—
Voltage regulator recovery time
tVRR
10
D
—
4
—
μs
1
2
3
Typical values are based on characterization data at VDD = 3.0 V, 25 °C unless otherwise stated.
This is the shortest pulse that is guaranteed to be recognized as a reset pin request.
To enter BDM mode following a POR, BKGD/MS should be held low during the power-up and for a hold time of tMSH after VDD
rises above VLVD
.
4
5
This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or
may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized.
Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range –40°C to 85°C.
textrst
RESET PIN
Figure 13. Reset Timing
MC9S08QB8 Series MCU Data Sheet, Rev. 3
18
Freescale Semiconductor
Electrical Characteristics
tIHIL
KBIPx
IRQ/KBIPx
tILIH
Figure 14. IRQ/KBIPx Timing
3.10.2 TPM Module Timing
Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that
can be used as the optional external source to the timer counter. These synchronizers operate from the
current bus rate clock.
Table 13. TPM Input Timing
No.
C
Function
Symbol
Min
Max
Unit
1
2
3
4
5
D
D
D
D
D
External clock frequency
External clock period
fTEXT
tTEXT
DC
4
1/4 fop
—
MHz
tCYC
tCYC
tCYC
tCYC
External clock high time
External clock low time
Input capture pulse width
tTCLKH
tTCLKL
fICPW
1.5
1.5
1.5
—
—
—
tCYC
ipg_clk
tTEXT
EXTERNAL
CLOCK
tTCLKL
tTCLKH
tICPW
INPUT
CAPTURE
Figure 15. Timer Input Capture Pulse
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
19
Electrical Characteristics
3.11 Analog Comparator (ACMP) Electricals
Table 14. Analog Comparator Electrical Specifications
C
Characteristic
Symbol
Min
Typical
Max
Unit
D
D
D
P
C
P
C
Supply voltage
VPWR
IDDAC
VAIN
1.8
—
20
—
3.6
35
V
μA
V
Supply current (active)
—
VSS – 0.3
—
Analog input voltage
VDD
40
Analog input offset voltage
Analog comparator hysteresis
Analog input leakage current
Analog comparator initialization delay
VAIO
VH
20
9.0
—
mV
mV
μA
μs
3.0
15.0
1.0
1.0
IALKG
tAINIT
—
—
—
3.12 ADC Characteristics
Table 15. 12-Bit ADC Operating Conditions
Characteristic
Conditions
Symbol
Min
Typical1
Max
Unit
Comment
Absolute
Delta to VDD (VDD – VDDA
VDDA
1.8
—
3.6
V
Supply voltage
2
)
ΔVDDA
–100
0
100
mV
2
Ground voltage Delta to VSS (VSS – VSSA
)
ΔVSSA
IDDAD
VADIN
–100
—
0
0.007
—
100
0.8
mV
μA
V
Supply Current
Input Voltage
Stop, Reset, Module Off
VREFL
VREFH
Input
Capacitance
CADIN
—
—
4.5
5
5.5
7
pF
Input
Resistance
RADIN
kΩ
12 bit mode
fADCK > 4MHz
fADCK < 4MHz
—
—
—
—
2
5
Analog Source
Resistance
10 bit mode
RAS
kΩ
External to MCU
f
ADCK > 4MHz
—
—
—
—
5
10
fADCK < 4MHz
8 bit mode (all valid fADCK
)
—
—
—
10
ADC
High Speed (ADLPC = 0)
0.4
8.0
Conversion
Clock Freq.
fADCK
MHz
Low Power (ADLPC = 1)
0.4
—
4.0
1
2
Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference
only and are not tested in production.
DC potential difference.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
20
Freescale Semiconductor
Electrical Characteristics
NOTE
pins do not exist in 16-pin package. The signals are derived
V
/V
DDA SSA
internally by double bonding to V /V pair of pins.
DD SS
SIMPLIFIED
INPUT PIN EQUIVALENT
ZADIN
CIRCUIT
SIMPLIFIED
CHANNEL SELECT
CIRCUIT
Pad
ZAS
leakage
due to
ADC SAR
ENGINE
input
protection
RAS
RADIN
+
VADIN
–
CAS
VAS
+
–
RADIN
RADIN
RADIN
INPUT PIN
INPUT PIN
INPUT PIN
CADIN
Figure 16. ADC Input Impedance Equivalency Diagram
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
21
Electrical Characteristics
Table 16. 12-Bit ADC Characteristics (V
= V
, V
= V
)
SSA
REFH
DDA
REFL
Characteristic
Conditions
C
Symbol
Min
Typical1
Max
Unit
Comment
Supply Current
ADLPC=1
ADLSMP=1
ADCO=1
T
IDDAD
—
120
—
—
—
1
μA
μA
μA
mA
Supply Current
ADLPC=1
ADLSMP=0
ADCO=1
T
T
T
IDDAD
IDDAD
IDDAD
—
—
—
202
288
Supply Current
ADLPC=0
ADLSMP=1
ADCO=1
Supply Current
ADLPC=0
ADLSMP=0
ADCO=1
0.532
Supply Current Stop, Reset, Module Off
T
P
IDDAD
—
2
0.007
3.3
0.8
5
μA
ADC
Asynchronous
Clock Source
High Speed (ADLPC = 0)
Low Power (ADLPC = 1)
tADACK
=
fADACK
MHz
1/fADACK
1.25
—
2
3.3
—
Short Sample
(ADLSMP = 0)
20
Conversion
Time(Including
sample time)
ADCK
cycles
T
T
tADC
Long Sample
(ADLSMP = 1)
See reference
manual for
conversion
—
—
—
40
3.5
—
—
—
Short Sample
(ADLSMP = 0)
time variances
ADCK
cycles
Sample Time
tADS
Long Sample
23.5
(ADLSMP = 1)
12-bit mode
10-bit mode
T
P
—
—
±3.0
±1
—
—
For 28-pin and
24-pin
packages only.
Includes
Total
Unadjusted
Error
ETUE
LSB2
8-bit mode
T
P
—
—
±0.5
±1.5
—
—
quantization
Total
Unadjusted
Error
10-bit mode
For 16-pin
package only.
Includes
ETUE
LSB2
LSB2
8-bit mode
T
—
±0.7
—
quantization
12-bit mode
10-bit mode
8-bit mode
T
P
T
—
—
—
±1.75
±0.5
±0.3
—
—
—
DNL
Differential
Non-Linearity
Monotonicity and No-Missing-Codes guaranteed
MC9S08QB8 Series MCU Data Sheet, Rev. 3
22
Freescale Semiconductor
Electrical Characteristics
) (continued)
Table 16. 12-Bit ADC Characteristics (V
= V
Min
, V
= V
REFL SSA
REFH
DDA
Characteristic
Conditions
12-bit mode
C
Symbol
Typical1
Max
Unit
Comment
T
—
—
—
—
—
—
—
±1.5
±0.5
±0.3
±1.5
±0.5
±0.5
±1.5
—
—
Integral
Non-Linearity
10-bit mode
8-bit mode
12-bit mode
10-bit mode
8-bit mode
10-bit mode
INL
LSB2
C
—
C
P
T
P
—
For 28-pin and
24-pin
packages only.
VADIN = VSSA
Zero-Scale
Error
±1.5
±0.5
±2.1
EZS
EZS
EFS
EFS
EQ
LSB2
LSB2
LSB2
LSB2
LSB2
For 16-pin
package only.
Zero-Scale
Error
8-bit mode
T
—
±0.5
±0.7
VADIN = VSSA
12-bit mode
10-bit mode
8-bit mode
10-bit mode
T
P
T
T
—
—
—
—
±1
±0.5
±0.5
±1
—
±1
For 28-pin and
24-pin
packages only.
VADIN = VDDA
Full-Scale
Error
±0.5
±1.5
For 16-pin
package only.
VADIN = VDDA
Full-Scale
Error
8-bit mode
T
—
±0.5
±0.5
12-bit mode
10-bit mode
8-bit mode
—
—
—
—
0
–1 to 0
—
—
±0.5
±0.5
—
Quantization
Error
D
—
12-bit mode
10-bit mode
8-bit mode
±1
Input Leakage
Error
Pad leakage3 *
RAS
D
EIL
±0.2
±0.1
1.646
1.769
±4
LSB2
0
±1.2
—
−40°C– 25°C
25°C– 85°C
—
—
Temp Sensor
Slope
D
D
m
mV/°C
—
Temp Sensor
Voltage
25°C
VTEMP25
—
701.2
—
mV
1
Typical values assume VDDA = 3.0 V, Temp = 25 °C, fADCK=1.0 MHz unless otherwise stated. Typical values are for reference
only and are not tested in production.
2
3
1 LSB = (VREFH – VREFL)/2N
Based on input pad leakage current. Refer to pad electricals.
3.13 Flash Specifications
This section provides details about program/erase times and program-erase endurance for the flash
memory.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
23
Electrical Characteristics
Program and erase operations do not require any special power sources other than the normal V supply.
DD
For more detailed information about program/erase operations, see the memory section.
Table 17. Flash Characteristics
C
Characteristic
Symbol
Min
Typical
Max
Unit
Supply voltage for program/erase
-40°C to 85°C
D
Vprog/erase
VRead
fFCLK
1.8
1.8
150
5
3.6
3.6
V
D
D
D
D
D
D
D
D
D
Supply voltage for read operation
Internal FCLK frequency1
Internal FCLK period (1/FCLK)
Byte program time (random location)(2)
Byte program time (burst mode)(2)
Page erase time2
Mass erase time(2)
Byte program current3
Page erase current3
V
200
6.67
kHz
μs
tFcyc
tprog
9
tFcyc
tFcyc
tFcyc
tFcyc
mA
mA
tBurst
4
4000
20,000
4
tPage
tMass
RIDDBP
RIDDPE
—
—
—
—
6
Program/erase endurance4
TL to TH = –40°C to + 85°C
T = 25 °C
C
—
10,000
15
—
100,000
—
—
cycles
years
C
Data retention5
tD_ret
100
—
1
2
The frequency of this clock is controlled by a software setting.
These values are hardware state machine controlled. User code does not need to count cycles. This information supplied
for calculating approximate time to program and erase.
3
4
The program and erase currents are additional to the standard run IDD. These values are measured at room temperatures
with VDD = 3.0 V, bus frequency = 4.0 MHz.
Typical endurance for flash was evaluated for this product family on the 9S12Dx64. For additional information on how
Freescale defines typical endurance, please refer to Engineering Bulletin EB619, Typical Endurance for Nonvolatile
Memory.
5
Typical data retention values are based on intrinsic capability of the technology measured at high temperature and
de-rated to 25°C using the Arrhenius equation. For additional information on how Freescale defines typical data retention,
please refer to Engineering Bulletin EB618, Typical Data Retention for Nonvolatile Memory.
3.14 EMC Performance
Electromagnetic compatibility (EMC) performance is highly dependant on the environment in which the
MCU resides. Board design and layout, circuit topology choices, location and characteristics of external
components as well as MCU software operation all play a significant role in EMC performance. The
system designer should consult Freescale applications notes such as AN2321, AN1050, AN1263,
AN2764, and AN1259 for advice and guidance specifically targeted at optimizing EMC performance.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
24
Freescale Semiconductor
Ordering Information
4
Ordering Information
This section contains ordering information for the device numbering system.
Example of the device numbering system:
8
C
XX
MC 9 S08 QB
Status
(MC = Fully Qualified)
Package designator (see Table 18)
Temperature range
(C = –40 °C to 85 °C)
Memory
(9 = Flash-based)
Core
Approximate flash size in KB
Family
5
Package Information
Table 18. Package Descriptions
Pin Count
Package Type
Abbreviation
Designator
Case No.
Document No.
28
24
16
Small Outline Integrated Circuit
Quad Flat Non-Leaded
SOIC
QFN
WL
GK
TG
751F
1982-01
948F
98ASB42345B
98ARL10608D
98ASH70247A
Thin Shrink Small Outline Package
TSSOP
5.1
Mechanical Drawings
The following pages are mechanical drawings for the packages described in Table 18.
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Freescale Semiconductor
25
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
How to Reach Us:
Home Page:
www.freescale.com
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Semiconductor was negligent regarding the design or manufacture of the part.
Japan:
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
For information on Freescale’s Environmental Products program, go to
http://www.freescale.com/epp.
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
© Freescale Semiconductor, Inc. 2008-2009. All rights reserved.
Beijing 100022
China
+86 10 5879 8000
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or +1-303-675-2140
Fax: +1-303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Document Number: MC9S08QB8
Rev. 3
3/2009
相关型号:
MC9S08QB8CWL
8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO28, ROHS COMPLIANT, MS-013AE, SOIC-28
ROCHESTER
©2020 ICPDF网 联系我们和版权申明