MMBTA55 [ROCHESTER]
500mA, 60V, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-236AB;
| 型号： | MMBTA55 |
| 厂家： | 
Rochester Electronics |
| 描述： | 500mA, 60V, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-236AB 光电二极管 晶体管 |
| 文件： | 总14页 (文件大小：2709K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MPSA55
MMBTA55
PZTA55
C
C
E
E
C
B
TO-92
C
B
SOT-23
Mark: 2H
B
SOT-223
E
PNP General Purpose Amplifier
This device is designed for general purpose amplifier applications
at collector currents to 300 mAꢀ Sourced from Process 73ꢀ See
MPSA56 for characteristicsꢀ
Absolute Maximum Ratings*
TA = 25°C unless otherwise noted
Symbol
Parameter
Value
Units
VCES
VCBO
VEBO
IC
Collector-Emitter Voltage
60
60
V
V
Collector-Base Voltage
Emitter-Base Voltage
4.0
V
Collector Current - Continuous
Operating and Storage Junction Temperature Range
500
mA
°C
-55 to +150
TJ, Tstg
*These ratings are limiting values above which the serviceability of any semiconductor device may be impairedꢀ
NOTES:
1) These ratings are based on a maximum junction temperature of 150 degrees Cꢀ
2) These are steady state limitsꢀ The factory should be consulted on applications involving pulsed or low duty cycle operationsꢀ
Thermal Characteristics
TA = 25°C unless otherwise noted
Symbol
Characteristic
Max
Units
MPSA55
*MMBTA55
**PZTA55
PD
Total Device Dissipation
Derate above 25°C
Thermal Resistance, Junction to Case
625
5.0
83.3
350
2.8
1,000
8.0
mW
mW/°C
°C/W
RθJC
Thermal Resistance, Junction to Ambient
200
357
125
Rθ
JA
°C/W
*Device mounted on FR-4 PCB 1ꢀ6" X 1ꢀ6" X 0ꢀ06ꢀ"
**Device mounted on FR-4 PCB 36 mm X 18 mm X 1ꢀ5 mm; mounting pad for the collector lead minꢀ 6 cm2ꢀ
ã 1997 Fairchild Semiconductor Corporation
MPSA55/MMBTA55/PZTA55, Rev A
PNP General Purpose Amplifier
(continued)
Electrical Characteristics
TA = 25°C unless otherwise noted
Symbol
Parameter
Test Conditions
Min
Max
Units
OFF CHARACTERISTICS
V(BR)CEO
Collector-Emitter Breakdown
IC = 1.0 mA, IB = 0
60
V
Voltage*
V(BR)CBO
V(BR)EBO
ICEO
Collector-Base Breakdown Voltage
60
V
V
IC = 100 µA, IE = 0
IE = 100 µA, IC = 0
VCE = 60 V, IB = 0
VCB = 60 V, IE = 0
Emitter-Base Breakdown Voltage
Collector-Cutoff Current
4.0
0.1
0.1
µ
µ
A
A
ICBO
Collector-Cutoff Current
ON CHARACTERISTICS
hFE
DC Current Gain
IC = 10 mA, VCE = 1.0 V
100
100
I
C = 100 mA, VCE = 1.0 V
Collector-Emitter Saturation Voltage IC = 100 mA, IB = 10 mA
0.25
1.2
V
VCE(sat)
VBE(
Base-Emitter On Voltage
IC = 100 mA, VCE = 1.0 V
V
on
)
SMALL SIGNAL CHARACTERISTICS
fT
Current Gain - Bandwidth Product
IC = 100 mA, VCE = 1.0 V,
f = 100 MHz
50
MHz
*Pulse Test: Pulse Width £ 300 ms, Duty Cycle £ 2ꢀ0%
TO-92 Tape and Reel Data
TO-92 Packaging
Configuration: Figure 1.0
Packaging Description:
TO-92 parts are shipped normally in tape. These reeled
parts in standard option are shipped with 2,000 units per
14” or 355.6cm diameter reel. This and some other options
are further described in the Packaging Information
table.These full reels are individually barcode labeled and
placed inside
a standard intermediate box (illustrated in
figure 1.0) made of recyclable corrugated brown paper.
One box contains one reel maximum. And these boxes
1 Reel per
Inner box
are placed inside
a barcode labeled shipping box which
comes in different sizes depending on the number of parts
shipped.
FKS Label
395mm x 375mm x 56mm
Inner box(2,000cap)
FKS Label
TO-92 Packaging
Configuration: Figure 2.0
Inner Box Bar Code Label Sample
TO-92 Packaging Information
MBB : NOR
S/T : LOGO
HIC : 0 P/T:O MIX: X
P/U : 660
I/B: LOGO
00 / 03 / 17
06:30
P
Standard
Standard
Standard
ETC:
Packaging Option
(no flow code) (no flow code) (no flow code)
Packaging type
Qty per Reel/Tube/ Bag
Reel Size
TNR
2,000
14”Dia
AMMO
BULK
1,000
-
1
01
DVC:
KA7812-AE
-
LOT: TKLEE777 Q’TY: 1000 W/W:0103
Inner Box Dimension (mm) 395x375x56 328x162x43 237x167x96
Max qty per Box
2,000 2,000 10,000
Outer Box Dimension (mm) 420x420x320 525x360x265 525x360x265
OPTION:
420mm x 420mm x 320mm
Outer box(10,000cap)
20000025
Outer Box Bar Code Label Sample
Max qty per Box
10,000
0.2080
30,000
0.2080
100,000
0.2080
00 / 03 / 17
07:30
Weight per unit (gm)
FKS Label
DVC:
LOT:
KA7812-AE
IMSYS777
12000
Note/Comments
IM
01
Q’TY:
88706892
7103
TO-92 AMMO Packaging
A710103105
Configuration: Figure 3.0
525mm x 360m x 265mm
Outer box (30,000cap)
15 Ammo boxes per
Outer Box
FKS Label
328mm x 162mm x 43mm
Inner box (2,000cap)
FKS Label
TO-92 Bulk Packing
Configuration: Figure 4.0
FKS Label
10 Vinyl bags per
Inner box
525mm x 360mm x 265mm
Outer box(100,000cap)
1,000 units per
Bulk Vinyl bag
237mm x 167mm x 96mm
Bulk Inner box(10,000cap)
FKS Label
October 2001, Rev. A
©2001 Fairchild Semiconductor Corporation
TO-92 Tape and Reel Data, continued
TO-92 Reeling Style
Configuration: Figure 5.0
Standard
Machine Option
TO-92 Radial Ammo Packaging
Configuration: Figure 6.0
Standard
Machine Option
FIRST WIRE OFF IS EMITTER
ADHESIVE TAPE IS ON THE TOP SIDE
FLAT OF TRANSISTOR IS ON BOTTOM
FIRST WIRE OFF IS COLLECTOR
ADHESIVE TAPE IS ON THE TOP SIDE
FLAT OF TRANSISTOR IS ON TOP
FIRST WIRE OFF IS COLLECTOR
ADHESIVE TAPE IS ON BOTTOM SIDE
FLAT OF TRANSISTOR IS ON TOP
FIRST WIRE OFF IS EMITTER
ADHESIVE TAPE IS ON BOTTOM SIDE
FLAT OF TRANSISTOR IS ON BOTTOM
October 2001, Rev. A
TO-92 Tape and Reel Data, continued
TO-92 Tape and Reel Taping
Dimension Configuration:
Figure 7.0
T
A1
jh
P
A
H1
W2
d
H
HO
J1
WO
W1
W
t
P1 F1 F2
P2
DO
ITEM DESCRIPTION
SYMBOL
DIMENSION
REMARK
PO
A1
A
4.58 (+ 0.25, - 0.15)
4.58 (+/- 0.20)
3.86 (max)
Body Width
Body Height
User Direction of Feed
T
Body Thickness
Lead-Wire Diameter
Pitch of Component
Feed Hole Pitch
d
0.46 (+/- 0.05)
12.7 (+/- 0.50)
12.7 (+/ -0.20)
6.35 (+/- 0.50)
2.50 (+ 0.3, - 0.10)
0.00 (+/- 1.00)
18.00 (+ 1.00, - 0.50)
6.00 (+/- 0.50)
9.00 (+/ -0.50)
1.00 (max)
P
P0
P2
F1,F2
jh
In Case of Reel
Package +/- 1.00
Hole Center to Component Center
Lead to Lead Distance
Component Alignment F-R
Tape Width
F1-F2= +/- 0.30
W
Hole-Down Tape Width
Hole Position
W0
W1
W2
H
Hole-Down Tape Position
19.50 (+/- 1.00)
16.00 (+/- 0.50)
27.0 (max)
Height of Component From Tape Center
Lead-Wire Clinch Height
Component Height
H + A <= H1
H0
H1
J1
D0
t
Lead-Wire (Tape Portion)
Feed Hole Diameter
2.50 (min)
4.00 (+/- 0.20)
0.65 (+/- 0.20)
3.85 (+/- 0.50)
Total Tape Thickness
P1
Position of Hole
TO-92 Reel
Configuration:
Note : All dimensions are in millimeters.
Figure 8.0
ELECTROSTATIC
SENSITIVE DEVICES
ITEM DESCRIPTION
SYSMBOL MINIMUM
MAXIMUM
D4
D1
Reel Diameter
D1
D2
D2
D3
D4
W1
W2
W3
13.975
1.160
0.650
3.100
2.700
0.370
1.630
14.025
1.200
0.700
3.300
3.100
0.570
1.690
2.090
D2
Arbor Hole Diameter (Standard)
(Small Hole)
FKS Label
Core Diameter
Hub Recess Inner Diameter
Hub Recess Depth
Flange to Flange Inner Width
Hub to Hub Center Width
W1
W3
W2
Note: All dimensions are inches
October 2001, Rev. A
TO-92 Package Dimensions
TO-92 (FS PKG CODE AM)
+0.25
–0.15
4.58
0.46 ±0.10
+0.10
–0.05
1.27TYP
1.27TYP
0.38
[1.27 ±0.20]
[1.27 ±0.20]
3.60 ±0.20
(R2.29)
Dimensions in Millimeters
August 1999, Rev B
SOT-23 Tape and Reel Data
SOT-23 Packaging
Configuration: Figure 1.0
Packaging Description:
SOT-23 parts are shipped in tape. The carrier tape is
made from
a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Activated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
3,000 units per 7” or 17.7cm diameter reel. The reels are
clear in color and is made of polystyrene plastic (anti-static
coated). This and some other options are further described
in the Packaging Information table. These full reels are
individually barcode labeled and placed inside a standard
intermediate box (illustrated in figure 1.0) made of
recyclable corrugated brown paper. One box contains five
Antistatic Cover Tape
reels maximum. And these boxes are placed inside
a
barcode labeled shipping box which comes in different
sizes depending on the number of parts shipped.
Static Dissipative
Embossed Carrier Tape
FKS Label
7H
7H
7H
7H
Pin 1
SOT-23 Unit Orientation
SOT-23 Packaging Information
Packaging Option
Standard
Packaging type
Qty per Reel/Tube/Bag
Reel Size
TNR
3,000
7” Dia
5 Reels per box
Inner Box Dimension (mm) 188x181x69
Max qty per Box
15,000
Outer Box Dimension (mm) 420x420x320
FKS Label
Max qty per Box
180,000
0.0084
-
Weight per unit (gm)
Weight per Reel (kg)
188mm x 181mm x 69mm
Inner box(15,000cap)
Note/Comments
Inner Box Barcode Label Sample
Outer Box Barcode Label Sample
MBB : NOR
S/T : LOGO
P/U : 660
I/B: LOGO
00 / 03 / 17
06:30
00 / 03 / 17
07:30
P
ETC:
HIC : 0 P/T:O MIX: X
DVC:
LOT:
KA7812-AE
IMSYS777
12000
IM
01
DVC:
Q’TY:
KA7812-AE
A710103105
88706892
7103
LOT:TKLEE777 Q’TY:1000 W/W: 0103
01
OPTION:
20000025
FKS Label
SOT-23 Tape Leader and Trailer
Configuration: Figure 2.0
420m x 420mm x 320mm
Outer box(180,000cap)
Carrier Tape
Components
Cover Tape
Trailer Tape
Leader Tape
640mm minimum or
80 empty pockets
1680mm minimum or
210 empty pockets
October 2001, Rev. A
©2001 Fairchild Semiconductor Corporation
SOT-23 Tape and Reel Data, continued
SOT-23 Embossed Carrier Tape
Configuration: Figure 3.0
P0
P2
D0
D1
T
E1
E2
W
F
Wc
B0
Tc
K0
A0
P1
User Direction of Feed
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
0.5mm
20 deg maximum
Typical
maximum
component
cavity
center line
0.5mm
maximum
B0
20 deg maximum component rotation
Typical
component
center line
Sketch A (Side or Front Sectional View)
Sketch C (Top View)
A0
Component Rotation
Component lateral movement
Sketch B (Top View)
Component Rotation
W1 Measured at Hub
SOT-23 Reel
Configuration: Figure 4.0
B Min
Dim C
Dim N
Dim A
max
Dim D
min
DETAIL AA
See detail AA
W3
7” Diameter Option
W2 max Measured at Hub
Dimensions are in inches and millimeters
Reel
Option
Tape Size
Dim A
Dim B
Dim C
Dim D
Dim N
Dim W1
Dim W2
Dim W3 (LSL-USL)
7.00
177.8
0.059
1.5
0.512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
2.165
55
0.331 +0.059/-0.000
8.4 +1.5/0
0.567
14.4
0.311 – 0.429
7.9 – 10.9
8.0mm
7” Dia
October 2001, Rev. A
SOT-23 Package Dimensions
SOT-23 (FS PKG CODE AU)
0.40 ±0.03
0.03~0.10
0.38 REF
+0.05
–0.023
0.40 ±0.03
0.12
0.96~1.14
2.90 ±0.10
0.95 ±0.03 0.95 ±0.03
1.90 ±0.03
0.508REF
Dimensions in Millimeters
August 1999, Rev B
SOT-223 Tape and Reel Data
SOT-223 Packaging
Configuration:
Figure 1.0
Packaging Description:
SOT-223 parts are shipped in tape. The carrier tape is
made from
a dissipative (carbon filled) polycarbonate
resin. The cover tape is a multilayer film (Heat Activated
Adhesive in nature) primarily composed of polyester film,
adhesive layer, sealant, and anti-static sprayed agent.
These reeled parts in standard option are shipped with
4000 units per 13”or 330cm diameter reel. The reels are
dark blue or black in color and is made of polystyrene
plastic (anti-static coated). This and some other options
are further described in the Packaging Information
table.These full reels are individually barcode labeled and
Antistatic Cover Tape
placed inside
a standard intermediate box (illustrated in
figure 1.0) made of recyclable corrugated brown paper.
One box contains four reels maximum. And these boxes
are placed inside a barcode labeled shipping box which
comes in different sizes depending on the number of parts
shipped.
Static Dissipative
Embossed Carrier Tape
FKS Label
T0133
T0133
T0133
T0133
F
FQT13N60
F
F
F
FQT13N60
FQT13N60
FQT13N60
SOT-223 Unit Orientation
4 Reels per box
SOT-223 Packaging Information
Packaging Option
Standard
Packaging type
Qty per Reel/Tube/Bag
Reel Size
TNR
4,000
13”Dia
Inner Box Dimension (mm)
Max qty per Box
339x352x68
16,000
FKS Label
Outer Box Dimension (mm)
Max qty per Box
420x420x320
64,000
Weight per unit (gm)
Weight per Reel(kg)
0.1118
339mm x 352mm x 68mm
Inner box(16,000cap)
-
Note/Comments
Inner Box Barcode Label Sample
Outer Box Barcode Label Sample
MBB : NOR
S/T : LOGO
P/U : 660
I/B: LOGO
00 / 03 / 17
06:30
00 / 03 / 17
07:30
P
ETC:
HIC : 0 P/T:O MIX: X
DVC:
LOT:
KA7812-AE
IMSYS777
12000
IM
01
DVC:
QT’ Y:
KA7812-AE
A710103105
88706892
7103
LOT:TKLEE777 Q’TY: 1000 W/W:0103
01
FKS Label
OPTION:
20000025
420mm x 420mm x 320mm
Outer box(64,000cap)
SOT-223 Tape Leader and Trailer
Configuration: Figure 2.0
Carrier Tape
Cover Tape
Components
Trailer Tape
Leader Tape
360mm minimum or
45 empty pockets
1520mm minimum or
190 empty pockets
October 2001, Rev. A
©2001 Fairchild Semiconductor Corporation
SOT-223 Tape and Reel Data, continued
SOT-223 Embossed Carrier Tape
Configuration:
Figure 3.0
P0
D0
T
E1
E2
F
W
K0
Wc
B0
Tc
A0
D1
P1
User Direction of Feed
Dimensions are in millimeter
A0
B0
W
D0
D1
E1
E2
F
P1
P0
K0
T
Wc
Tc
Pkg type
SOT-223
6.83
7.42
12.0
1.55
1.50
1.75
10.25
min
5.50
8.0
4.0
1.80
9.50
0.10
max
0.30
+/-0.05
+/-0.10
+/-0.10
+/-0.2
+/-0.05
+/-0.10
+/-0.10
+/-0.05
+/-0.1
+/-0.1
+/-0.10
+/-0.1
(12mm)
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481
rotational and lateral movement requirements (see sketches A, B, and C).
0.5mm
maximum
20 deg maximum
Typical
component
cavity
center line
0.5mm
maximum
B0
20 deg maximum component rotation
Typical
component
center line
Sketch A (Side or Front Sectional View)
Component Rotation
Sketch C (Top View)
Component lateral movement
A0
Sketch B (Top View)
Component Rotation
SOT-223 Reel
Configuration:
Figure 4.0
W1 Measured at Hub
B Min
Dim C
Dim A
max
Dim D
min
Dim N
DETAIL AA
See detail AA
W3
13”Diameter Option
W2 max Measured at Hub
Dimensions are in inches and millimeters
Reel
Tape Size
Dim A
Dim B
Dim C
Dim D
Dim N
Dim W1
Dim W2
Dim W3 (LSL-USL)
Option
13.00
330
0.059
1.5
0.512 +0.020/-0.008
13 +0.5/-0.2
0.795
20.2
4.00
100
0.488 +0.078/-0.000
12.4 +2/0
0.724
18.4
0.468 – 0.606
11.9 – 15.4
12.0mm
13” Dia
October 2001, Rev. A
SOT-223 Package Dimensions
SOT-223 (FS PKG CODE AV)
3.00 ±0.10
MAX1.80
+0.04
–0.02
0.06
2.30 TYP
0.70 ±0.10
+0.10
–0.05
(0.95)
(0.95)
0.25
4.60 ±0.25
6.50 ±0.20
Dimensions in Millimeters
August 1999, Rev B
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.
â
SMART START™
STAR*POWER™
Stealth™
VCX™
FAST
ACEx™
Bottomless™
CoolFET™
OPTOLOGIC™
OPTOPLANAR™
PACMAN™
FASTr™
FRFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SyncFET™
GlobalOptoisolator™
GTO™
HiSeC™
ISOPLANAR™
LittleFET™
MicroFET™
MicroPak™
MICROWIRE™
CROSSVOLT™
DenseTrench™
DOME™
POP™
Power247™
PowerTrenchâ
QFET™
EcoSPARK™
E2CMOSTM
TinyLogic™
QS™
EnSignaTM
TruTranslation™
UHC™
QT Optoelectronics™
Quiet Series™
SILENTSWITCHERâ
FACT™
FACT Quiet Series™
UltraFETâ
STAR*POWER is used under license
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITYARISING OUT OF THE APPLICATION OR USE OFANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICESORSYSTEMSWITHOUTTHEEXPRESSWRITTENAPPROVALOFFAIRCHILDSEMICONDUCTORCORPORATION.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, or (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in significant injury to the
user.
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or
In Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Obsolete
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. H4
相关型号：
MMBTA55-13
Small Signal Bipolar Transistor, 0.5A I(C), 60V V(BR)CEO, 1-Element, PNP, Silicon, PLASTIC PACKAGE-3
DIODES
©2020 ICPDF网 联系我们和版权申明