MZP4735ARLG [ROCHESTER]
6.2 V, 1 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, LEAD FREE, PLASTIC, CASE 59-10, 2 PIN;
| 型号： | MZP4735ARLG |
| 厂家： | 
Rochester Electronics |
| 描述： | 6.2 V, 1 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, LEAD FREE, PLASTIC, CASE 59-10, 2 PIN 测试 二极管 |
| 文件： | 总7页 (文件大小：771K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MZP4729A Series
3 Watt DO-41 Surmetict
30 Zener Voltage Regulators
This is a complete series of 3 Watt Zener diodes with limits and
excellent operating characteristics that reflect the superior capabilities
of silicon-oxide passivated junctions. All this in an axial-lead,
transfer-molded plastic package that offers protection in all common
environmental conditions.
http://onsemi.com
Cathode
Anode
Specification Features:
•ꢀZener Voltage Range - 3.6 V to 30 V
•ꢀESD Rating of Class 3 (>16 KV) per Human Body Model
•ꢀSurge Rating of 98 Watt @ 1 ms
•ꢀMaximum Limits Guaranteed on up to Six Electrical Parameters
•ꢀPackage No Larger than the Conventional 1 Watt Package
•ꢀThese are Pb-Free Devices*
Mechanical Characteristics:
AXIAL LEAD
CASE 59
PLASTIC
CASE: Void free, transfer-molded, thermosetting plastic
FINISH: All external surfaces are corrosion resistant and leads are
readily solderable
MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES:
260°C, 1/16″ from the case for 10 seconds
POLARITY: Cathode indicated by polarity band
MOUNTING POSITION: Any
MARKING DIAGRAM
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
A
MZP
47xxA
YYWWG
G
Max. Steady State Power Dissipation
@ T = 75°C, Lead Length = 3/8″
P
3
W
D
L
Derate above 75°C
24
1
mW/°C
Steady State Power Dissipation
@ T = 50°C
P
D
W
A
Derate above 50°C
6.67
mW/°C
°C
Operating and Storage Temperature
Range
T , T
J
-65 to +200
A
= Assembly Location
MZP47xxA = Device Number
stg
YY
WW
G
= Year
= Work Week
= Pb-Free Package
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
(Note: Microdot may be in either location)
ORDERING INFORMATION
†
Device
Package
Shipping
MZP47xxARLG
Axial Lead 6000/Tape & Reel
(Pb-Free)
MZP47xxATAG
Axial Lead 4000/Ammo Pack
(Pb-Free)
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
*For additional information on our Pb-Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
©ꢀ Semiconductor Components Industries, LLC, 2007
July, 2007 - Rev. 4
1
Publication Order Number:
MZP4729A/D
MZP4729A Series
ELECTRICAL CHARACTERISTICS (T = 25°C unless
A
otherwise noted, V = 1.5 V Max @ I = 200 mA for all types)
I
F
F
I
F
Symbol
Parameter
V
Reverse Zener Voltage @ I
Reverse Current
Z
ZT
I
ZT
Z
I
Maximum Zener Impedance @ I
Reverse Current
ZT
ZT
V
Z
V
R
V
I
ZT
ZK
V
F
R
I
Z
ZK
Maximum Zener Impedance @ I
ZK
I
Reverse Leakage Current @ V
Breakdown Voltage
R
R
V
R
I
F
Forward Current
V
I
Forward Voltage @ I
F
F
Zener Voltage Regulator
Surge Current @ T = 25°C
R
A
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted, V = 1.5 V Max @ I = 200 mA for all types)
A
F
F
Zener Voltage (Note 2)
Zener Impedance (Note 3)
Leakage Current
I
R
(Note 4)
V (Volts)
Z
@ I
Z
ZT
@ I
Z
ZK
@ I
I @ V
R
ZT
ZT
ZK
R
Device†
(Note 1)
Device
Marking
Min
Nom
Max
mA
W
W
mA
mA Max
Volts
mA
MZP4729A, G
MZP4735A, G
MZP4729A
MZP4735A
3.42
5.89
3.6
6.2
3.78
6.51
69
41
10
2
400
700
1
1
100
10
1
3
1260
730
MZP4746A, G
MZP4749A, G
MZP4750A, G
MZP4746A
MZP4749A
MZP4750A
17.10
22.80
25.65
18
24
27
18.90
25.20
28.35
14
10.5
9.5
20
25
35
750
750
750
0.25
0.25
0.25
5
5
5
13.7
18.2
20.6
250
190
170
1. TOLERANCE AND TYPE NUMBER DESIGNATION
The type numbers listed have a standard tolerance on the nominal zener voltage of 5%.
2. ZENER VOLTAGE (V ) MEASUREMENT
Z
ON Semiconductor guarantees the zener voltage when measured at 90 seconds while maintaining the lead temperature (T ) at 30°C 1°C,
L
3/8″ from the diode body.
3. ZENER IMPEDANCE (Z ) DERIVATION
Z
The zener impedance is derived from 60 seconds AC voltage, which results when an AC current having an rms value equal to 10% of the
DC zener current (I or I ) is superimposed on I or I .
ZK
ZT ZK
4. SURGE CURRENT (I ) NON-REPETITIVE
ZT
R
The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or
equivalent sine wave pulse of 1/120 second duration superimposed on the test current, I , per JEDEC standards. However, actual device
ZT
capability is as described in Figure 3 of the General Data sheet for Surmetic 30s.
†The “G'' suffix indicates Pb-Free package.
http://onsemi.com
2
MZP4729A Series
5
4
3
L = LEAD LENGTH
TO HEAT SINK
L = 1/8″
L = 3/8″
2
1
0
L = 1″
0
20 40
60
80 100 120 140 160 180
200
T , LEAD TEMPERATURE (°C)
L
Figure 1. Power Temperature Derating Curve
30
20
D =0.5
0.2
10
7
5
0.1
3
2
t
1
P
PK
0.05
t
2
DUTY CYCLE, D =t /t
1 2
0.02
0.01
1
0.7
0.5
NOTE: BELOW 0.1 SECOND, THERMAL
RESPONSE CURVE IS APPLICABLE
TO ANY LEAD LENGTH (L).
SINGLE PULSE DT = q (t)P
PK
JL
JL
D = 0
REPETITIVE PULSES DT = q (t,D)P
JL JL PK
0.3
0.0001 0.0002
0.0005 0.001 0.002
0.005
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
10
t, TIME (SECONDS)
Figure 2. Typical Thermal Response L, Lead Length = 3/8 Inch
3
1K
2
RECTANGULAR
NONREPETITIVE
1
0.5
500
T = 125°C
A
WAVEFORM
T Ă=Ă25°C PRIOR
300
200
J
TO INITIAL PULSE
0.2
0.1
0.05
100
50
0.02
0.01
0.005
30
20
T = 125°C
A
0.002
0.001
0.0005
0.0003
10
1
2
5
10
20
50 100 200 400 1000
0.1 0.2 0.3 0.5
1
2
3
5
10 20 30 50 100
NOMINAL V (VOLTS)
Z
PW, PULSE WIDTH (ms)
Figure 3. Maximum Surge Power
Figure 4. Typical Reverse Leakage
http://onsemi.com
3
MZP4729A Series
APPLICATION NOTE
Since the actual voltage available from a given zener
diode is temperature dependent, it is necessary to determine
junction temperature under any set of operating conditions
in order to calculate its value. The following procedure is
recommended:
DT is the increase in junction temperature above the lead
JL
temperature and may be found from Figure 2 for a train of
power pulses (L = 3/8 inch) or from Figure 10 for dc power.
DTJL = qJL PD
For worst‐case design, using expected limits of I , limits
Z
Lead Temperature, T , should be determined from:
L
of P and the extremes of T (DT ) may be estimated.
D
J
J
Changes in voltage, V , can then be found from:
TL = qLA PD + TA
Z
q
P is the power dissipation. The value for q will vary and
is the lead‐to‐ambient thermal resistance (°C/W) and
LA
DV = qVZ DTJ
D
LA
q
, the zener voltage temperature coefficient, is found
VZ
from Figures 5 and 6.
depends on the device mounting method. q is generally
LA
30-40°C/W for the various clips and tie points in common
use and for printed circuit board wiring.
Under high power‐pulse operation, the zener voltage will
vary with time and may also be affected significantly by the
zener resistance. For best regulation, keep current
excursions as low as possible.
Data of Figure 2 should not be used to compute surge
capability. Surge limitations are given in Figure 3. They are
lower than would be expected by considering only junction
temperature, as current crowding effects cause temperatures
to be extremely high in small spots resulting in device
degradation should the limits of Figure 3 be exceeded.
The temperature of the lead can also be measured using a
thermocouple placed on the lead as close as possible to the
tie point. The thermal mass connected to the tie point is
normally large enough so that it will not significantly
respond to heat surges generated in the diode as a result of
pulsed operation once steady‐state conditions are achieved.
Using the measured value of T , the junction temperature
L
may be determined by:
TJ = TL + DTJL
TEMPERATURE COEFFICIENT RANGES
(90% of the Units are in the Ranges Indicated)
10
1000
500
8
6
4
200
100
2
0
RANGE
50
20
10
-2
-4
10
20
50
100
200
400
1000
3
4
5
6
7
8
9
10
11
12
V , ZENER VOLTAGE @ I (VOLTS)
Z ZT
V , ZENER VOLTAGE @ I (VOLTS)
Z ZT
Figure 5. Units to 12 Volts
Figure 6. Units 10 to 400 Volts
http://onsemi.com
4
MZP4729A Series
ZENER VOLTAGE versus ZENER CURRENT
(Figures 7, 8 and 9)
100
50
100
50
30
20
30
20
10
10
5
3
2
5
3
2
1
1
0.5
0.5
0.3
0.2
0.3
0.2
0.1
0.1
0
1
2
3
4
5
6
7
8
9
10
0
10
20
30
40
50
60
70
80
90 100
V , ZENER VOLTAGE (VOLTS)
Z
V , ZENER VOLTAGE (VOLTS)
Z
Figure 7. VZ = 3.3 to 10 Volts
Figure 8. VZ = 12 to 82 Volts
10
5
2
1
0.5
0.2
0.1
100
150
200
250
300
350
400
V , ZENER VOLTAGE (VOLTS)
Z
Figure 9. VZ = 100 to 400 Volts
80
70
60
50
40
30
20
10
0
L
L
T
L
PRIMARY PATH OF
CONDUCTION IS THROUGH
THE CATHODE LEAD
0
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1
L, LEAD LENGTH TO HEAT SINK (INCH)
Figure 10. Typical Thermal Resistance
http://onsemi.com
5
MZP4729A Series
PACKAGE DIMENSIONS
AXIAL LEAD
CASE 59-10
ISSUE U
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO-41 OUTLINE SHALL APPLY
4. POLARITY DENOTED BY CATHODE BAND.
5. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
K
D
F
INCHES
DIM MIN MAX
MILLIMETERS
A
K
MIN
4.10
2.00
0.71
---
MAX
5.20
2.70
0.86
1.27
---
A
B
D
F
0.161 0.205
0.079 0.106
0.028 0.034
--- 0.050
POLARITY INDICATOR
OPTIONAL AS NEEDED
(SEE STYLES)
F
K
1.000
--- 25.40
SURMETIC is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800-282-9855 Toll Free
ꢁUSA/Canada
Europe, Middle East and Africa Technical Support:
ꢁPhone: 421 33 790 2910
Japan Customer Focus Center
ꢁPhone: 81-3-5773-3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
ꢁLiterature Distribution Center for ON Semiconductor
ꢁP.O. Box 5163, Denver, Colorado 80217 USA
ꢁPhone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
ꢁFax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
ꢁEmail: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
MZP4729A/D
相关型号：
MZP4735ARR1
6.2V, 1W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, PLASTIC, CASE 59-10, 2 PIN
ONSEMI
MZP4735ARR2
6.2V, 1W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, PLASTIC, CASE 59-10, 2 PIN
ONSEMI
MZP4735ATA
6.2V, 1W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, PLASTIC, CASE 59-10, 2 PIN
ONSEMI
MZP4735ATAG
6.2V, 1W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41, LEAD FREE, PLASTIC, CASE 59-10, 2 PIN
ONSEMI
©2020 ICPDF网 联系我们和版权申明