NE555N 概述
1 Func, PDIP8, DIP-8 模拟波形发生功能
NE555N 规格参数
是否无铅: | 不含铅 | 是否Rohs认证: | 不符合 |
生命周期: | Contact Manufacturer | 零件包装代码: | DIP |
包装说明: | DIP-8 | 针数: | 8 |
Reach Compliance Code: | unknown | ECCN代码: | EAR99 |
HTS代码: | 8542.39.00.01 | 风险等级: | 5.82 |
Is Samacsys: | N | 其他特性: | IT CAN ALSO OPERATE AT 15V NOMINAL SUPPLY |
模拟集成电路 - 其他类型: | PULSE; RECTANGULAR | JESD-30 代码: | R-PDIP-T8 |
JESD-609代码: | e0 | 长度: | 9.2 mm |
功能数量: | 1 | 端子数量: | 8 |
最高工作温度: | 70 °C | 最低工作温度: | |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | DIP |
封装形状: | RECTANGULAR | 封装形式: | IN-LINE |
峰值回流温度(摄氏度): | NOT SPECIFIED | 认证状态: | Not Qualified |
座面最大高度: | 5.08 mm | 最大供电电压 (Vsup): | 16 V |
最小供电电压 (Vsup): | 4.5 V | 标称供电电压 (Vsup): | 5 V |
表面贴装: | NO | 温度等级: | COMMERCIAL |
端子面层: | TIN LEAD | 端子形式: | THROUGH-HOLE |
端子节距: | 2.54 mm | 端子位置: | DUAL |
处于峰值回流温度下的最长时间: | NOT SPECIFIED | 宽度: | 7.62 mm |
Base Number Matches: | 1 |
NE555N 数据手册
通过下载NE555N数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载www.fairchildsemi.com
LM555/NE555/SA555
Single Timer
Features
Description
• High Current Drive Capability (200mA)
• Adjustable Duty Cycle
• Temperature Stability of 0.005%/°C
• Timing From µSec to Hours
The LM555/NE555/SA555 is a highly stable controller
capable of producing accurate timing pulses. With a
monostable operation, the time delay is controlled by one
external resistor and one capacitor. With an astable
• Turn off Time Less Than 2µSec
operation, the frequency and duty cycle are accurately
controlled by two external resistors and one capacitor.
Applications
8-DIP
• Precision Timing
• Pulse Generation
• Time Delay Generation
• Sequential Timing
1
8-SOP
1
Internal Block Diagram
R
R
R
1
8
7
6
5
Vcc
GND
Comp.
Discharging Tr.
2
Trigger
Discharge
Threshold
OutPut
Stage
3
Output
F/F
Comp.
Control
Voltage
4
Reset
Vref
Rev. 1.0.3
©2002 Fairchild Semiconductor Corporation
LM555/NE555/SA555
Absolute Maximum Ratings (T = 25°C)
A
Parameter
Symbol
Value
16
Unit
V
Supply Voltage
V
CC
Lead Temperature (Soldering 10sec)
Power Dissipation
T
300
600
°C
LEAD
P
mW
D
Operating Temperature Range
LM555/NE555
SA555
T
0 ~ +70
-40 ~ +85
°C
°C
OPR
Storage Temperature Range
T
-65 ~ +150
STG
2
LM555/NE555/SA555
Electrical Characteristics
(T = 25°C, V
A
= 5 ~ 15V, unless otherwise specified)
CC
Parameter
Symbol
Conditions
-
Min.
Typ. Max.
Unit
V
Supply Voltage
V
4.5
-
3
16
6
CC
V
V
= 5V, R = ∞
-
-
mA
mA
CC
CC
L
Supply Current (Low Stable) (Note1)
I
CC
= 15V, R = ∞
7.5
15
L
Timing Error (Monostable)
Initial Accuracy (Note2)
Drift with Temperature (Note4)
Drift with Supply Voltage (Note4)
ACCUR
∆t/∆T
-
-
1.0
50
0.1
3.0
0.5
%
ppm/°C
%/V
R = 1kΩ to100kΩ
C = 0.1µF
A
∆t/∆V
CC
Timing Error (Astable)
Intial Accuracy (Note2)
Drift with Temperature (Note4)
Drift with Supply Voltage (Note4)
ACCUR
∆t/∆T
R = 1kΩ to 100kΩ
2.25
150
0.3
-
%
ppm/°C
%/V
A
C = 0.1µF
∆t/∆V
CC
V
V
V
V
= 15V
= 5V
9.0
2.6
-
10.0
3.33
10.0
3.33
0.1
11.0
4.0
-
V
V
CC
CC
CC
CC
Control Voltage
V
C
= 15V
= 5V
V
Threshold Voltage
Threshold Current (Note3)
Trigger Voltage
V
TH
-
-
V
I
-
-
0.25
2.2
5.6
2.0
1.0
0.4
µA
V
TH
V
V
V
= 5V
= 15V
= 0V
1.1
4.5
1.67
5
CC
CC
TR
V
TR
V
Trigger Current
Reset Voltage
Reset Current
I
0.01
0.7
µA
V
TR
V
RST
RST
-
-
0.4
I
0.1
mA
V
= 15V
CC
I
I
= 10mA
= 50mA
-
-
0.06
0.3
0.25
0.75
V
V
SINK
SINK
Low Output Voltage
High Output Voltage
V
OL
V
I
= 5V
= 5mA
CC
SINK
0.05
0.35
V
V
I
I
= 15V
CC
= 200mA
= 100mA
12.5
-
V
V
SOURCE
SOURCE
12.75 13.3
V
OH
V
= 5V
CC
2.75
3.3
-
V
I
= 100mA
SOURCE
Rise Time of Output (Note4)
Fall Time of Output (Note4)
Discharge Leakage Current
t
-
-
-
-
-
-
100
100
20
-
-
ns
ns
nA
R
t
F
I
100
LKG
Notes:
1. When the output is high, the supply current is typically 1mA less than at V
CC
= 5V.
2. Tested at V
= 5.0V and V
= 15V.
CC
CC
3. This will determine the maximum value of R + R for 15V operation, the max. total R = 20MΩ, and for 5V operation, the max.
A
B
total R = 6.7MΩ.
4. These parameters, although guaranteed, are not 100% tested in production.
3
LM555/NE555/SA555
Application Information
Table 1 below is the basic operating table of 555 timer:
Table 1. Basic Operating Table
Threshold Voltage
Trigger Voltage
(V )(PIN 2)
tr
Discharging Tr.
(PIN 7)
Reset(PIN 4)
Output(PIN 3)
(V )(PIN 6)
th
Don't care
Don't care
Low
High
High
High
Low
Low
-
ON
ON
-
V
> 2Vcc / 3
V
> 2Vcc / 3
th
th
Vcc / 3 < V < 2 Vcc / 3 Vcc / 3 < V < 2 Vcc / 3
th
th
V
< Vcc / 3
V
< Vcc / 3
th
High
OFF
th
When the low signal input is applied to the reset terminal, the timer output remains low regardless of the threshold voltage or
the trigger voltage. Only when the high signal is applied to the reset terminal, the timer's output changes according to
threshold voltage and trigger voltage.
When the threshold voltage exceeds 2/3 of the supply voltage while the timer output is high, the timer's internal discharge Tr.
turns on, lowering the threshold voltage to below 1/3 of the supply voltage. During this time, the timer output is maintained
low. Later, if a low signal is applied to the trigger voltage so that it becomes 1/3 of the supply voltage, the timer's internal
discharge Tr. turns off, increasing the threshold voltage and driving the timer output again at high.
1. Monostable Operation
+Vcc
102
R
A
4
8
101
100
RESET
Vcc
Trigger
7
6
DISCH
TRIG
OUT
2
3
THRES
CONT
10-1
10-2
10-3
C1
5
GND
R
L
C2
1
10-5
10-4
10-3
10-2
10-1
100
101
102
Time Delay(s)
Figure 2. Resistance and Capacitance vs.
Time delay(t )
Figure 1. Monoatable Circuit
d
Figure 3. Waveforms of Monostable Operation
4
LM555/NE555/SA555
Figure 1 illustrates a monostable circuit. In this mode, the timer generates a fixed pulse whenever the trigger voltage falls
below Vcc/3. When the trigger pulse voltage applied to the #2 pin falls below Vcc/3 while the timer output is low, the timer's
internal flip-flop turns the discharging Tr. off and causes the timer output to become high by charging the external capacitor C1
and setting the flip-flop output at the same time.
The voltage across the external capacitor C1, V increases exponentially with the time constant t=R *C and reaches 2Vcc/3
C1
A
at td=1.1R *C. Hence, capacitor C1 is charged through resistor R . The greater the time constant R C, the longer it takes
A
A
A
for the V to reach 2Vcc/3. In other words, the time constant R C controls the output pulse width.
C1
A
When the applied voltage to the capacitor C1 reaches 2Vcc/3, the comparator on the trigger terminal resets the flip-flop,
turning the discharging Tr. on. At this time, C1 begins to discharge and the timer output converts to low.
In this way, the timer operating in the monostable repeats the above process. Figure 2 shows the time constant relationship
based on R and C. Figure 3 shows the general waveforms during the monostable operation.
A
It must be noted that, for a normal operation, the trigger pulse voltage needs to maintain a minimum of Vcc/3 before the timer
output turns low. That is, although the output remains unaffected even if a different trigger pulse is applied while the output is
high, it may be affected and the waveform does not operate properly if the trigger pulse voltage at the end of the output pulse
remains at below Vcc/3. Figure 4 shows such a timer output abnormality.
Figure 4. Waveforms of Monostable Operation (abnormal)
2. Astable Operation
+Vcc
100
(RA+2RB)
R
A
10
1
4
8
RESET
Vcc
7
6
DISCH
TRIG
OUT
2
3
R
B
0.1
THRES
CONT
0.01
C1
5
GND
1E-3
100m
R
C2
L
1
1
10
100
1k
10k
100k
Frequency(Hz)
Figure 6. Capacitance and Resistance vs. Frequency
Figure 5. Astable Circuit
5
LM555/NE555/SA555
Figure 7. Waveforms of Astable Operation
An astable timer operation is achieved by adding resistor R to Figure 1 and configuring as shown on Figure 5. In the astable
B
operation, the trigger terminal and the threshold terminal are connected so that a self-trigger is formed, operating as a multi
vibrator. When the timer output is high, its internal discharging Tr. turns off and the V increases by exponential
C1
function with the time constant (R +R )*C.
A
B
When the V , or the threshold voltage, reaches 2Vcc/3, the comparator output on the trigger terminal becomes high,
C1
resetting the F/F and causing the timer output to become low. This in turn turns on the discharging Tr. and the C1 discharges
through the discharging channel formed by R and the discharging Tr. When the V falls below Vcc/3, the comparator
C1
B
output on the trigger terminal becomes high and the timer output becomes high again. The discharging Tr. turns off and the
rises again.
V
C1
In the above process, the section where the timer output is high is the time it takes for the V to rise from Vcc/3 to 2Vcc/3,
C1
and the section where the timer output is low is the time it takes for the V to drop from 2Vcc/3 to Vcc/3. When timer output
C1
is high, the equivalent circuit for charging capacitor C1 is as follows:
RA
RB
Vcc
C1
Vc1(0-)=Vcc/3
dv
V
– V(0-)
c1
cc
C ------------- = ------------------------------
(1)
(2)
1
dt
R + R
A
B
V
(0+) = V
⁄ 3
C1
CC
t
- –------------------------------------
(R + R )C1
A
B
2
3
--
V
(t) = V
1 –
e
(3)
C1
CC
Since the duration of the timer output high state(t ) is the amount of time it takes for the V (t) to reach 2Vcc/3,
C1
H
6
LM555/NE555/SA555
t
H
- –------------------------------------
(R + R )C1
A
B
2
3
2
3
--
--
V
(t) =
V
= V
1 –
e
(4)
C1
CC
CC
t
= C (R + R )In2 = 0.693(R + R )C
(5)
H
1
A
B
A
B
1
The equivalent circuit for discharging capacitor C1, when timer output is low is, as follows:
RB
C1
VC1(0-)=2Vcc/3
RD
dv
1
+ R
C1
----------------------
C -------------- +
V
= 0
(6)
(7)
1
C1
R
dt
A
B
t
------------------------------------
-
(R + R )C1
2
A
D
--
V
(t) =
V
C1
e
3
CC
Since the duration of the timer output low state(t ) is the amount of time it takes for the V (t) to reach Vcc/3,
L
C1
t
L
------------------------------------
-
(R + R )C1
1
3
2
3
A
D
--
--
V
=
V
(8)
CC
e
CC
t
= C (R + R )In2 = 0.693(R + R )C
(9)
L
1
B
D
B
D
1
Since R is normally R >>R although related to the size of discharging Tr.,
D
B
D
tL=0.693R C
(10)
B 1
Consequently, if the timer operates in astable, the period is the same with
'T=t +t =0.693(RA+R )C +0.693R C =0.693(R +2R )C ' because the period is the sum of the charge time and discharge
H
L
B
1
B 1
A
B
1
time. And since frequency is the reciprocal of the period, the following applies.
1
T
1.44
frequency,
f = --- = ---------------------------------------
(11)
(R + 2R )C
A
B
1
3. Frequency divider
By adjusting the length of the timing cycle, the basic circuit of Figure 1 can be made to operate as a frequency divider. Figure
8. illustrates a divide-by-three circuit that makes use of the fact that retriggering cannot occur during the timing cycle.
7
LM555/NE555/SA555
Figure 8. Waveforms of Frequency Divider Operation
4. Pulse Width Modulation
The timer output waveform may be changed by modulating the control voltage applied to the timer's pin 5 and changing the
reference of the timer's internal comparators. Figure 9 illustrates the pulse width modulation circuit.
When the continuous trigger pulse train is applied in the monostable mode, the timer output width is modulated according to
the signal applied to the control terminal. Sine wave as well as other waveforms may be applied as a signal to the control
terminal. Figure 10 shows the example of pulse width modulation waveform.
+Vcc
R
A
4
8
RESET
Vcc
7
6
5
Trigger
Output
DISCH
TRIG
2
3
THRES
CONT
OUT
Input
C
GND
1
Figure 9. Circuit for Pulse Width Modulation
Figure 10. Waveforms of Pulse Width Modulation
5. Pulse Position Modulation
If the modulating signal is applied to the control terminal while the timer is connected for the astable operation as in Figure 11,
the timer becomes a pulse position modulator.
In the pulse position modulator, the reference of the timer's internal comparators is modulated which in turn modulates the
timer output according to the modulation signal applied to the control terminal.
Figure 12 illustrates a sine wave for modulation signal and the resulting output pulse position modulation : however, any wave
shape could be used.
8
LM555/NE555/SA555
+Vcc
R
R
A
B
4
8
Vcc
RESET
7
6
5
DISCH
TRIG
2
3
THRES
CONT
Output
OUT
Modulation
C
GND
1
Figure 12. Waveforms of pulse position modulation
Figure 11. Circuit for Pulse Position Modulation
6. Linear Ramp
When the pull-up resistor RA in the monostable circuit shown in Figure 1 is replaced with constant current source, the V
C1
increases linearly, generating a linear ramp. Figure 13 shows the linear ramp generating circuit and Figure 14 illustrates the
generated linear ramp waveforms.
+Vcc
R1
R
E
4
8
RESET
Vcc
7
6
DISCH
Q1
TRIG
OUT
2
3
R2
THRES
CONT
Output
C1
5
GND
C2
1
Figure 14. Waveforms of Linear Ramp
In Figure 13, current source is created by PNP transistor Q1 and resistor R1, R2, and R .
Figure 13. Circuit for Linear Ramp
E
V
– V
CC
R
E
I
= --------------------------
(12)
C
E
Here, V
E is
R
2
---------------------
V
= V
+
V
(13)
E
BE
CC
R
+ R
1
2
For example, if Vcc=15V, R =20kΩ, R1=5kW, R2=10kΩ, and V =0.7V,
BE
E
V =0.7V+10V=10.7V
E
Ic=(15-10.7)/20k=0.215mA
9
LM555/NE555/SA555
When the trigger starts in a timer configured as shown in Figure 13, the current flowing through capacitor C1 becomes a
constant current generated by PNP transistor and resistors.
Hence, the V is a linear ramp function as shown in Figure 14. The gradient S of the linear ramp function is defined as
C
follows:
V
p – p
T
S = ----------------
(14)
Here the Vp-p is the peak-to-peak voltage.
If the electric charge amount accumulated in the capacitor is divided by the capacitance, the V comes out as follows:
C
V=Q/C
(15)
The above equation divided on both sides by T gives us
V
T
Q ⁄ T
C
--- = -----------
(16)
and may be simplified into the following equation.
S=I/C (17)
In other words, the gradient of the linear ramp function appearing across the capacitor can be obtained by using the constant
current flowing through the capacitor.
If the constant current flow through the capacitor is 0.215mA and the capacitance is 0.02µF, the gradient of the ramp function
at both ends of the capacitor is S = 0.215m/0.022µ = 9.77V/ms.
10
LM555/NE555/SA555
Mechanical Dimensions
Package
Dimensions in millimeters
8-DIP
6.40 ±0.20
0.252 ±0.008
#1
#4
#8
#5
3.30 ±0.30
0.130 ±0.012
5.08
MAX
0.200
7.62
3.40 ±0.20
0.134 ±0.008
0.300
0.33
0.013
MIN
11
LM555/NE555/SA555
Mechanical Dimensions (Continued)
Package
Dimensions in millimeters
8-SOP
0.1~0.25
MIN
0.004~0.001
1.55 ±0.20
0.061 ±0.008
#8
#5
#1
#4
6.00 ±0.30
0.236 ±0.012
1.80
0.071
MAX
3.95 ±0.20
0.156 ±0.008
°
5.72
0.225
0~8
0.50 ±0.20
0.020 ±0.008
12
LM555/NE555/SA555
Ordering Information
Product Number
LM555CN
Package
8-DIP
Operating Temperature
0 ~ +70°C
LM555CM
8-SOP
Product Number
NE555N
Package
8-DIP
Operating Temperature
0 ~ +70°C
NE555D
8-SOP
Product Number
SA555
Package
8-DIP
Operating Temperature
-40 ~ +85°C
SA555D
8-SOP
13
LM555/NE555/SA555
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, and (c) whose failure to
perform when properly used in accordance with
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
11/29/02 0.0m 001
Stock#DSxxxxxxxx
2002 Fairchild Semiconductor Corporation
NE555N 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
NE555N-14 | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP14 | 获取价格 | |
NE555N-14-A | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP14 | 获取价格 | |
NE555N-14-B | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP14 | 获取价格 | |
NE555N-14SIIA | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP14 | 获取价格 | |
NE555N-14SIIB | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP14 | 获取价格 | |
NE555N-B | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP8 | 获取价格 | |
NE555NSIIA | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP8 | 获取价格 | |
NE555NSIIB | PHILIPS | Analog Waveform Generation Function, BIPolar, PDIP8 | 获取价格 | |
NE555P | NEC | PRECISION TIMERS | 获取价格 | |
NE555P | TI | PRECISION TIMERS | 获取价格 |
NE555N 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6