SPX3819S-3-3 [ROCHESTER]
3.3V FIXED POSITIVE LDO REGULATOR, 0.7V DROPOUT, PDSO8, MO-012AA, SOIC-8;型号: | SPX3819S-3-3 |
厂家: | Rochester Electronics |
描述: | 3.3V FIXED POSITIVE LDO REGULATOR, 0.7V DROPOUT, PDSO8, MO-012AA, SOIC-8 光电二极管 输出元件 调节器 |
文件: | 总43页 (文件大小:1585K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SPX3819
500mA, Low-Noise LDO Voltage Regulator
FEATURES
ADJ/BYP
GND
EN
NC
1
2
8
7
6
■ Low Noise: 40µV Possible
■ High Accuracy: 1%
SPX3819
8 Pin DFN
V
3
4
NC
IN
■ Reverse Battery Protection
■ Low Dropout: 340mV at Full Load
■ Low Quiescent Current: 90µA
■ Zero Off-Mode Current
5
NC
V
OUT
■ Fixed Output: 1.2V, 1.5V, 1.8V, 2.5V, 3.0V,
APPLICATIONS
3.1V, 3.3V, 5.0V. Adj. Output also available.
■ Battery Powered Systems
■ Cordless Phones
■ Available in RoHS Compliant, Lead Free
Packages: 5 Pin SOT-23, 8 Pin Narrow
SOIC and 8 pin 2X3 DFN
■ Radio Control Systems
■ Portable/Palm Top/Notebook Computers
■ Portable Consumer Equipment
■ Portable Instrumentation
■ Bar Code Scanners
■ SMPS Post Regulators
DESCRIPTION
The SPX3819 is a positive voltage regulator with a low dropout voltage and low noise output. In
addition, this device offers a very low ground current of 800µA at 100mA output. The SPX3819 has
an initial tolerance of less than 1% max and a logic compatible ON/OFF switched input. When
disabled, power consumption drops to nearly zero. Other key features include reverse battery
protection, current limit, and thermal shutdown. The SPX3819 includes a reference bypass pin for
optimal low noise output performance. With its very low output temperature coefficient, this device
also makes a superior low power voltage reference.
The SPX3819 is an excellent choice for use in battery-powered applications such as cordless
telephones, radio control systems, and portable computers. It is available in several fixed voltages
-- 1.2V, 1.5V, 1.8V, 2.5V, 3.0V, 3.1V, 3.3V, 5.0V -- or with an adjustable output. This device is offered
in 8 pin NSOIC, 8 pin DFN and 5-pin SOT-23 packages.
TYPICAL APPLICATION CIRCUIT
VIN
1
VOUT
5
+
2
SPX3819
GND
EN
+
3
4
BYP
(Opt.)
ENABLE may be tied directly to V
IN
TOP View
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
1
ABSOLUTE MAXIMUM RATINGS
Power Dissipation ...................................................... Internally Limited
Lead Temp. (Soldering, 5 Seconds) ........................................... 260°C
Operating Junction Temperature Range ................... -40°C to +125°C
Input Supply Voltage ........................................................ -20V to +20V
Enable Input Voltage ........................................................ -20V to +20V
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
Input Voltage ................................................................... +2.5V to+16V
Operating Junction Temperature Range ................... -40°C to +125°C
Enable Input Voltage ........................................................... 0.0V to VIN
TJ=25°C, VOUT + 1V, for 1.2V Option VIN=VOUT + 1.2V IL=100µA, CL=1µF, and VENABLE ≥ꢀ2.4V. The
♦ denotes the
specifications which apply over full operating temperature range -40°C to +85°C, unless otherwise specified.
PARAMETER
MIN
TYP
MAX
UNITS
♦ꢀ
♦
CONDITIONS
Output Voltage Tolerance
-1
-2
+1
+2
%
Output Voltage Temperature Coef.
Line Regulation
57
0.04
0.05
10
ppm/°C
%/V
%
0.1
0.4
VIN=VOUT + 1V to 16V
IL = 0.1mA to 500mA
IL = 100µA
Load Regulation
Dropout Voltage
(VIN-VO)(Note 2)
60
80
mV
♦ꢀ
♦ꢀ
♦ꢀ
♦
125
180
340
0.05
90
175
250
mV
mV
mV
µA
IL = 50mA
IL = 150mA
IL = 500mA
350
450
550
700
Quiescent Current (IGND
)
3
8
VENABLE ≤ꢀ0.4V
VENABLE ≤ꢀ0.25V
♦ꢀ
♦ꢀ
♦
Ground Pin Current (IGND
)
150
190
µA
IL = 100µA
IL = 50mA
IL = 150mA
IL = 500mA
250
1.0
650
900
µA
2.0
2.5
mA
mA
♦
6.5
25.0
30.0
♦
Ripple Rejection (PSRR)
Current Limit (ILIMIT
70
dB
)
800
mA
VOUT = 0.0V
950
♦
Output Noise (eNO
)
300
40
µVRMS
µVRMS
IL=10mA, CL=1.0µF, CIN=1µF,
(10Hz-100kHz)
IL=10mA, CL=10µF, CBYP =1µF,
CIN =1µF, (10Hz-100kHz)
Input Voltage Level Logic Low (VIL)
Input Voltage Level Logic High (VIH
ENABLE Input Current
0.4
V
V
OFF
ON
)
2
0.01
3
2
µA
VIL ≤ꢀ0.4V
VIH ≥ꢀ2.0V
20
Thermal Resistance (Note 1)
191
128.4
59
°C/W
°C/W
°C/W
♦ꢀ
♦ꢀ
♦ꢀ
SOT-23-5 / Junction to Ambient
NSOIC-8 / Junction to Ambient
DFN-8 / Junction to Ambient
NOTES
Note 1: The maximum allowable power dissipation is a function of maximum operating junction temperature, TJ(max) the junction to ambient thermal
resistance, and the ambient θJA, and the ambient temperature TA. The maximum allowable power dissipation at any ambient temperature is
given: PD(max) = (TJ(max)-TA)/θJA, exceeding the maximum allowable power limit will result in excessive die temperature; thus, the regulator will
go into thermal shutdown. The θJA of the SPX3819 is 220°C/W mounted on a PC board.
Note 2: Not applicable to output voltage 2V or less.
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
2
TYPICAL PERFORMANCE CHARACTERISTICS
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
160
150
140
130
120
100
90
3.3V Device
VIN= 4.3V
CL = 1.0µF
80
70
60
3.3V Device
C = 1.0µF
L
L
I
= 100µA
4
0
100
200
300
400
500
6
8
10
12
14
16
I
(mA)
V
(V)
L
IN
Ground Current vs Input Voltage
Ground Current vs Load Current
14.0
3.350
3.345
3.340
3.335
3.330
3.325
3.320
3.315
3.310
3.305
3.3V Device
V
= 4.3V
IN
12.0
10.0
C
= 1.0µF
L
8.0
6.0
4.0
2.0
0.0
3.3V Device
C = 1.0µF
L
I
= 100µA
L
3.300
3.295
3.290
4
6
8
10
12
14
16
0
100
200
300
400
500
V
(V)
IN
I
(mA)
L
Output Voltage vs Input Voltage
Ground Current vs Load Current in Dropout
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
3
TYPICAL PERFORMANCE CHARACTERISTICS: Continued
3
.316
.314
350
300
250
200
150
100
50
3
3.3V Device
3.3V Device
V
= 4.3V
IN
CL = 1.0µF
C
= 1.0µF
L
3.312
3
3
3
.310
.308
.306
3
.304
3
.302
.300
0
3
0
100
200
300
400
500
0
100
200
300
400
500
I (mA)
L
I
L
(mA)
Output Voltage vs Load Current
Dropout Voltage vs Load Current
130
120
110
100
90
360
340
320
300
280
260
240
220
200
3.3V Device
VIN= 4.3µF
CL= 1.0µF
IL = 100µA
3.3V Device
VIN = 4.3
CL= 1.0µF
IL = 50mA
80
70
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
Temperature (°C)
Ground Current vs Temperature with 50mA Load
Ground Current vs Temperature with 100µA Load
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
4
TYPICAL PERFORMANCE CHARACTERISTICS: Continued
14.0
8.0
7.5
7.0
6.5
6.0
3.3V Device
VIN= 4.3µF
3.3V Device
VIN= 4.3µF
CL= 1.0µF
IL = 500mA
CL= 1.0µF
13.5
13.0
12.5
12.0
11.5
11.0
10.5
IL = 500mA
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
Temperature (°C)
Ground Current vs Temperature in Dropout
Ground Current vs Temperature with 500mA Load
3.400
3.380
1.30
3.3V Device
C = 1.0µF
L
I
L
= 100µA
3.3V Device
1.25
1.20
1.15
1.10
1.05
1.00
V
= 4.3µF
IN
= 1.0µF
3.360
3.340
3.320
3.300
2.280
2.260
2.240
2.220
2.200
C
L
L
I
= 500mA
-40
-20
0
20
40
60
80
100
120
4
6
8
10
(V)
12
14
16
Temperature (°C)
V
IN
Output Voltage vs Temperature
ENABLE Voltage, ON threshold, vs Input Voltage
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
5
TYPICAL PERFORMANCE CHARACTERISTICS: Continued
350
Cin = 1uFT,
Cout = 1uFT
Cin = 1uFT,
300
250
200
150
100
Cout = 2.2uFT
Cin = 1uFT
Cout = 10uFT
50
0
1
10
100
1000
10000 100000 1000000
Bypass Cap (pF)
Line Transient Response for 3.3V Device
Output Noise vs Bypass Capacitor Value IL = 10mA,
10Hz - 100kHz
Load Transient Response for 3.3V Device
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
6
APPLICATION INFORMATION
The SPX3819 requires an output capacitor for
device stability. Its value depends upon the
application circuit. In general, linear regulator
stability decreases with higher output currents.
In applications where the SPX3819 is sourcing
less current, a lower output capacitance may be
sufficient. For example, a regulator outputting
only 10mA, requires approximately half the
capacitance as the same regulator sourcing
150mA.
concern. The SPX3819 start-up speed is in-
versely proportional to the size of the BYP
capacitor. Applications requiring a slow ramp-
up of the output voltage should use a larger
CBYP. However, if a rapid turn-on is necessary,
the BYP capacitor can be omitted.
The SPX3819’s internal reference is available
through the BYP pin.
Benchtestingisthebestmethodfordetermining
the proper type and value of the capacitor since
the high frequency characteristics of electro-
lytic capacitors vary widely, depending on type
and manufacturer. A high quality 2.2µF alumi-
num electrolytic capacitor works in most appli-
cation circuits, but the same stability often can
be obtained with a 1µF tantalum electrolytic.
Figure 1 represents a SPX3819 standard appli-
cation circuit. The EN (enable) pin is pulled
high (>2.0V) to enable the regulator.
To disable the regulator, EN < 0.4V.
The SPX3819 in Figure 2 illustrates a typical
adjustable output voltage configuration. Two
resistors (R1 and R2) set the output voltage. The
output voltage is calculated using the formula:
With the SPX3819 adjustable version, the mini-
mumvalueofoutputcapacitanceisafunctionof
the output voltage. The value decreases with
higher output voltages, since closed loop gain is
increased.
VOUT = 1.235V x [ 1 + R1/R2]
R2 must be > 10 kΩꢀand for best results, R2
shouldbebetween22kΩ and47kΩ.
Typical Applications Circuits
A 10nF capacitor on the BYP pin will signifi-
cantly reduce output noise, but it may be left
unconnected if the output noise is not a major
VIN
1
VOUT
5
VOUT
VIN
1
5
4
+
+
R1
R2
2
2
SPX3819
SOT-23
SPX3819
GND
EN
+
GND
EN
+
3
3
4
BYP
(Opt.)
Hi-ON
Lo-OFF
ENABLE may be tied directly to V
IN
TOP View
TOP View
Figure 2. Typical Adjustable Output Voltage Configuration
Figure 1. Standard Application Circuit
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
7
PACKAGE: PIN DESCRIPTION
Pin #
nSOIC
Pin #
DFN
Pin #
SOT-3
Pin Name
Description
2
5-8
3
3
7
5
1
1
2
5
3
VIN
GND
VOUT
EN
Supply Input
Ground
Regulator Output
1
Enable(input). CMOS compatible
control input. Logic high = enable;
logic low or open = shutdown
4
-
8
4
-
ADJ/BYP Adjust(input). Feedback input.
Connect to resistive voltage-divider
network
4, 6
NC
No Connect
PACKAGE: PINOUTS
ADJ/BYP
GND
EN
NC
1
GND
8
EN
1
2
8
7
6
SPX3819
SPX3819
GND
7
V
IN
2
8 Pin DFN
8 Pin nSOIC
V
3
4
NC
IN
3
4
V
6
5
GND
GND
OUT
5
NC
V
OUT
ADJ/BYP
Note: The bottom exposed pad for the SPX3819
DFN package is connected to GND.
V
ADJ/BYP
4
OUT
5
SPX3819
5 Pin SOT-23
1
IN
2
GND
3
EN
V
Jun 5-07 Rev E
SPX3819 500mA, Low Noise LDO Voltage Regulator
© 2007 Sipex Corporation
8
Solved by
TM
Appendix and Web Link Information
For further assistance:
Email:
Sipexsupport@sipex.com
WWW Support page:
Sipex Application Notes:
Product Change Notices:
http://www.sipex.com/content.aspx?p=support
http://www.sipex.com/applicationNotes.aspx
http://www.sipex.com/content.aspx?p=pcn
Sipex Corporation
Solved by
Headquarters and
Sales Office
233 South Hillview Drive
Milpitas, CA95035
tel: (408) 934-7500
faX: (408) 935-7600
TM
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of
any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
The following sections contain information which is more
changeable in nature and is therefore generated as appendices.
1) Package Outline Drawings
2) Ordering Information
If Available:
3) Frequently Asked Questions
4) Evaluation Board Manuals
5) Reliability Reports
6) Product Characterization Reports
7) Application Notes for this product
8) Design Solutions for this product
Datasheet Appendix & Web Link Information
© 2007 Sipex Corporation
ORDERING INFORMATION
Accuracy
Quantity
Part Number
MSL Level Status Package Pack Type
RoHS
SPX3819S-L/TR
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 250ºC
L1 @ 250ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
L1 @ 260ºC
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
CF
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
DFN8
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
TUBE
2500
2500
2500
2500
2500
2500
2500
98
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
SPX3819S-L-1-8/TR
SPX3819S-L-2-5/TR
SPX3819S-L-3-0/TR
SPX3819S-L-3-1/TR
SPX3819S-L-3-3/TR
SPX3819S-L-5-0/TR
SPX3819S-L
SPX3819S-L-1-8
TUBE
98
SPX3819S-L-2-5
TUBE
98
SPX3819S-L-3-0
TUBE
98
SPX3819S-L-3-1
TUBE
98
SPX3819S-L-3-3
TUBE
98
SPX3819S-L-5-0
TUBE
98
SPX3819M5-L
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Not in Bulk
Tape & Reel
Tape & Reel
Tape & Reel
TUBE
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
3000
3000
2500
2500
98
SPX3819M5-L-1-2
SPX3819M5-L-1-5
SPX3819M5-L-1-8
SPX3819M5-L-2-5
SPX3819M5-L-3-0
SPX3819M5-L-3-1
SPX3819M5-L-3-3
SPX3819M5-L-5-0
SPX3819M5-L/TR
SPX3819M5-L-1-2/TR
SPX3819M5-L-1-5/TR
SPX3819M5-L-1-8/TR
SPX3819M5-L-2-5/TR
SPX3819M5-L-3-0/TR
SPX3819M5-L-3-1/TR
SPX3819M5-L-3-3/TR
SPX3819M5-L-5-0/TR
SPX3819R2-L-1-2
SPX3819R2-L-1-2/TR
SPX3819S-L-1-2/TR
SPX3819S-L-1-5/TR
SPX3819S-L-1-2
CF
DFN8
CF
SOIC-8
CF
SOIC-8
CF
SOIC-8
SPX3819S-L-1-5
CF
SOIC-8
TUBE
98
ORDERING INFORMATION
Accuracy
Quantity
Part Number
SPX3819R2-L
MSL Level Status Package Pack Type
RoHS
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
L1 @ 250ºC
L1 @ 250ºC
L1 @ 250ºC
L1 @ 250ºC
L1 @ 250ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
L1 @ 240ºC
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
EOL
DFN8
DFN8
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Tape & Reel
Tape & Reel
Tape & Reel
TUBE
3000
3000
3000
3000
3000
3000
3000
3000
2500
2500
98
SPX3819R2-L-1-5
SPX3819R2-L-1-8
SPX3819R2-L-3-3
SPX3819R2-L-5-0
SPX3819R2-1-2
SPX3819R2-3-3
SPX3819R2-1-2/TR
SPX3819S/TR
DFN8
DFN8
DFN8
DFN8
DFN8
DFN8
NSOIC8
NSOIC8
NSOIC8
NSOIC8
SOIC-8
SPX3819S-2-5/TR
SPX3819S
SPX3819S-2-5
TUBE
98
SPX3819S-3-3/TR
SPX3819S-1-8
Tape & Reel
TUBE
2500
98
SOIC-8
SPX3819S-3-3
SOIC-8
TUBE
98
SPX3819S-5-0
SOIC-8
TUBE
98
SPX3819M5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Not in Bulk
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
Tape & Reel
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
SPX3819M5-1-2
SPX3819M5-1-5
SPX3819M5-1-8
SPX3819M5-2-5
SPX3819M5-3-0
SPX3819M5-3-1
SPX3819M5-3-3
SPX3819M5-5-0
SPX3819M5/TR
SPX3819M5-1-2/TR
SPX3819M5-1-5/TR
SPX3819M5-1-8/TR
SPX3819M5-2-5/TR
SPX3819M5-3-0/TR
SPX3819M5-3-3/TR
SPX3819M5-5-0/TR
For further assistance:
Email:
Sipexsupport@sipex.com
WWW Support page:
Sipex Application Notes:
http://www.sipex.com/content.aspx?p=support
http://www.sipex.com/applicationNotes.aspx
Solved by
Sipex Corporation
Headquarters and
Sales Office
TM
233 South Hillview Drive
Milpitas, CA 95035
tel: (408) 934-7500
fax: (408) 935-7600
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not
assume any liability arising out of the application or use of any product or circuit described herein; neither
does it convey any license under its patent rights nor the rights of others.
Solved by
SPX3819: FAQ
TM
Part Number: SPX38ꢀ9
Date: Septꢀ4-06
Question:
Assuming a nominal load of 250mA @ 3V DC, how much ground current will be consumed? With a 6V input, will
the part even get warm? How about with a ꢀ2V input?
Answer:
The SPX38ꢀ9 data sheet contains a graph of ground current vs load current for your review.
Also we suggest that you download the Thermal Considerations application note which includes a few example
calculations from the SPX38ꢀ9:
http://www.sipex.com/files/ApplicationNotes/LDOThermal.pdf
The Linear Regulator Heat Calculator could also prove helpful:
http://www.sipex.com/files/ApplicationNotes/ThermalCalculator.xls
Customer bench testing is strongly recommended using intended application circuit to ensure proper operation.
Question:
Is this part similar to your SP6203 CMOS part in the above regard? Or, is it like a conventional regulator (LM7805)
where the excess voltage turns into heat?
Answer:
All LDO’s will transfer most of its energy to heat. To minimize this temperature rise keep the input to output voltage
difference slightly above dropout voltage. See the applications note mentioned above.
Question:
Can ceramic capacitors be used on the output?
Answer:
Ceramic capacitors may be used for this part. For Tantalum or Aluminum Electrolytic types, keep the Equivalent
Series Resistance (ESR) as small as possible.
Question:
Considering the PSRR is 70db, what is a better strategy for filtering the 60Hz ripple from the wall cube? A big high
voltage electrolytic on the input or a smaller, low voltage ceramic on the output? Or, a combination of both?
Answer:
A small common mode choke would be best for filtering this ripple. Variations / combinations of input capacitance
might also help but bench testing would be required.
SIPEX FAQ
ꢀ
© 2006 Sipex Corporation
Sipexsupport@sipex.com
For further assistance, contact Sipex Technical Support:
Question:
Is there any practical limit to how much capacitance is used on the input or output?
Answer:
Input and output capacitance may be increased without limit.
Question:
It would appear, from the data sheet, increasing the Bypass capacitor above 0.0ꢀuF has little improvement in
terms of noise. We use a special low ESL/ESR 0.1uF ceramic as standard for RF bypassing. Any concerns
about using these on your Bypass pin as well?
Answer:
If the bypass pin is to be used a ꢀ0nF ceramic capacitor is suggested. You may also use the value / type
mentioned. The only concern with the bypass feature is that startup time is increased. If startup time is a
concern then the bypass pin should be kept open. Different values of bypass capacitor will result in different
startup times.
Question:
A portion of this application involves modulating a IR LED with a 400KHz signal having a 50% duty cycle or less.
Assumming a drive level of ꢀ AMP per 25µS pulse, will your device even see this as an overload and go into
current limiting? If so, should a large electrolytic be employed on the output?
Answer:
This is a little difficult to answer not knowing how you plan on modulating the LED. If the enable input is used for
modulation it is possible that the device may not react fast enough to provide an output. This is very much true
if the Bypass pin is used. If the output load exceeds the current limit trip point then the output will be turned off
to protect the device. However. if the output is always on and modulation is done with some external circuitry,
then adding extra capacitance to the output could satisfy the current demand of the LED so as not to cause
current limit activation.
Question:
This part is quite attractive in terms of its Reverse Battery Protection feature. Do you have any other more
current/better alternatives?
Answer:
For a 500mA output current device this is the best Sipex offers for package size and performance. Check our
LDO products page for all of Sipex LDO offerings.
http://www.sipex.com/productselector.aspx?family=LowDropOut
SIPEX FAQ
2
© 2006 Sipex Corporation
Sipexsupport@sipex.com
For further assistance, contact Sipex Technical Support:
Question:
If a 3V battery pack was connected to the output, without a “wall wart” connected to the input, would any
current flow back through the device?
Answer:
The datasheet does not state that this device is operable in a pre-biased output condition; therefore, leakage
may occur.
Question:
If the 3V battery pack was connected to the input, what would the output voltage be with a 250mA load?
Answer:
If the input voltage is above dropout voltage then the part will regulate for the entire output current range up
to 500mA.
SIPEX FAQ
3
© 2006 Sipex Corporation
Sipexsupport@sipex.com
For further assistance, contact Sipex Technical Support:
Product Characterization Report
for the
SPX5205 Family of Products
SPX3819, SPX5205 Products
Prepared By: Velvet Doung, Salvador Wu & Greg West
Date: October 6, 2006
SPX5205
Product Family
Characterization Report
Table of Contents
Section
Page
Introduction
3
3
4
6
Characterization Procedure
Data Summary for Key Parameters
Conclusions
Data Histograms
Appendix A
Page 2 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
Introduction: This product family characterization was done as part of the
qualification of Sipex’s fabrication site transfer from Sipex’s Hillview Fab in
Milpitas, CA, to a contract foundry, Silan, in Hangzhou, China. This
characterization report summarizes data for key SPX5205 product family
characteristics and contains distributions for all parameters. A complete listing of
the product numbers covered by the characterization report is included in the
“Conclusion” section of this report. A distribution for a given parameter shows
different temperature data which are at -40ºC, 25ºC, and 85ºC.
Wafer Fab: Silan
Fab Location: Hangzhou, China
Process: Silan – bp4
MS: 1631
Characterization Procedure:
Silan Lot number(s): CA10068
Hillview Lot number(s): A133102
Temperatures: Ambient (25C), 85C, -40C
Tester: TMT
Test Program: SPX5205_S_33_01_FT
Page 3 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
Data Summary:
Key Parameter Across Temperature Data Summary
Units
Hillview
Fab
Distribution Distribution
Hillview
Fab
Hillview
Fab
Cpk
Silan Fab
Distribution
Mean
Silan Fab
Distribution
Variance
Silan Fab
Cpk
Parameter
Mean
Variance
-40C
Vout@1mA
Vout@150mA
Load Reg
V
V
3.3063
3.3059
0.0163
3.3033
3.3031
0.0095
4.4206
165.9586
2.5512
0.0766
0.1293
65.9978
0.1791
245.0682
0.0145
0.0143
0.0239
0.0146
0.0146
0.0022
0.4011
5.1199
0.7638
0.0507
0.1387
5.4764
0.0095
0.7598
0.1453
0.1377
3.3101
3.3096
0.0155
3.3066
3.3084
0.0106
4.8494
171.5026
6.6740
0.0418
0.1244
61.9901
0.1367
244.7949
0.0145
0.0146
0.0124
0.0160
0.0159
0.0092
0.1847
3.1504
0.6094
0.0348
0.1015
12.8836
0.0136
1.0248
0.2313
0.2201
%
2.5591
>4.0000
0.1374
Vout@16V
Vout@Ven16V
Line Reg
V
0.0755
V
0.0698
0.1756
%/V
mV
mV
uA
uA
uA
uA
mA
mA
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
2.0921
3.2365
Vdrop@100uA
Vdrop@150mA
Ien_Hi
>4.0000
>4.0000
>4.0000
>4.0000
2.8759
Ien_Lo
Iq
Ignd@100uA
Ignd@150mA
Ilim
3.5913
1.6302
>4.0000
>4.0000
>4.0000
>4.0000
25C
V
V
Vout@1mA
3.3116
3.3101
0.0454
3.3063
3.3063
0.0154
5.8073
198.4826
2.0744
0.0889
0.0712
67.5626
0.1561
246.5068
0.0127
0.0127
0.0133
0.0127
0.0127
0.0012
0.4263
1.4465
0.5860
0.0381
0.0202
3.5699
0.0103
0.5756
0.3030
0.2635
3.3155
3.3140
0.0434
3.3113
3.3113
0.0125
6.2024
202.5361
5.6495
0.0491
0.0848
68.1415
0.1256
247.4643
0.0052
0.0051
0.0161
0.0053
0.0054
0.0029
0.1236
1.1720
0.7200
0.0227
0.0140
3.3238
0.0077
0.5002
0.9831
0.9141
Vout@150mA
Load Reg
%
3.8768
3.2412
Vout@16V
Vout@Ven16V
Line Reg
V
0.1658
0.7049
V
0.1654
0.7008
%/V
mV
mV
uA
uA
uA
uA
mA
mA
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
Vdrop@100uA
Vdrop@150uA
Ien_Hi
Ien_Lo
Iq
Ignd@100uA
Ignd@150uA
Ilim
Page 4 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
85C
V
V
Vout@1mA
3.2970
3.2945
0.0768
3.3219
3.3189
0.0366
7.3246
234.8495
1.7742
0.1911
2.2378
65.8955
0.1215
236.4959
0.0109
0.0109
0.0226
0.0150
0.0143
0.0160
0.4241
2.2662
0.4554
0.0379
0.6659
3.1628
0.0122
0.8179
-0.0910
-0.1690
1.8173
3.2998
3.2950
0.1440
3.3184
3.3188
0.0310
8.0661
239.0377
4.6596
0.1981
1.5455
64.1807
0.0960
236.7823
0.0058
0.0058
0.0261
0.0062
0.0097
0.0172
0.1438
1.8582
0.3992
0.0446
0.3054
3.4968
0.0086
0.6988
-0.0113
-0.2835
0.7146
Vout@150mA
Load Reg
%
Vout@16V
Vout@Ven16V
Line Reg
V
0.4887
0.9950
V
0.4418
0.6478
%/V
mV
mV
uA
uA
uA
uA
mA
mA
1.3243
1.3345
Vdrop@100uA
Vdrop@150uA
Ien_Hi
>4.0000
>4.0000
>4.0000
>4.0000
-0.6196
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
>4.0000
-0.5954
>4.0000
>4.0000
>4.0000
Ien_Lo
Iq
Ignd@100uA
Ignd@150uA
Ilim
Page 5 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
Conclusion:
Characterization data over temperature and Vcc range show datasheet
parameters meet the spec. Cpk’s for most parameters are comparable between
Hillview and Silan although many show a strong temperature dependence that
tends to produce lower Cpk’s in this analysis.
The performance of SPX5205 parts fabricated at Silan are comparable to the
current SPX5205 parts built from the Hillview fab.
This characterization report applies to the following SPX5205 family of product
part numbers:
SPX3819A1-3-3
SPX3819A1-L-3-3 SPX3819R2-1-8
SPX3819R2-1-5
SPX3819S-L-3-3
SPX3819S-L-5-0
SPX3819T-1-8
SPX3819T-3-0
SPX3819T-3-1
SPX3819T-3-3
SPX3819T5-1-8
SPX3819T5-3-0
SPX3819U-L-3-0
SPX3819U-L-3-1
SPX3819U-L-3-3
SPX3819U-L-5-0
SPX5205M5
SPX5205M5-1-2
SPX5205M5-1-5
SPX5205M5-1-8
SPX5205M5-2-0
SPX5205M5-2-5
SPX3819M3-1-8
SPX3819M3-3-0
SPX3819M3-3-1
SPX3819M3-3-3
SPX3819M3-L-1-8 SPX3819R2-5-0
SPX3819M3-L-3-0 SPX3819R2-L
SPX3819R2-2-5
SPX3819R2-3-0
SPX3819R2-3-1
SPX3819R2-3-3
SPX3819M3-L-3-1 SPX3819R2-L-1-2 SPX3819T5-3-1
SPX3819M3-L-3-3 SPX3819R2-L-1-5 SPX3819T5-3-3
SPX3819M5
SPX3819R2-L-1-8 SPX3819T5-L-1-8 SPX5205M5-2-8
SPX3819R2-L-2-5 SPX3819T5-L-3-0 SPX5205M5-3-0
SPX3819R2-L-3-0 SPX3819T5-L-3-1 SPX5205M5-3-3
SPX3819R2-L-3-1 SPX3819T5-L-3-3 SPX5205M5-5-0
SPX3819M5-1-2
SPX3819M5-1-5
SPX3819M5-1-8
SPX3819M5-2-5
SPX3819M5-3-0
SPX3819M5-3-1
SPX3819M5-3-3
SPX3819M5-5-0
SPX3819M5-L
SPX3819M5-L-1-2 SPX3819S-3-1
SPX3819M5-L-1-5 SPX3819S-3-3
SPX3819M5-L-1-8 SPX3819S-5-0
SPX3819M5-L-2-5 SPX3819S-L
SPX3819M5-L-3-0 SPX3819S-L-1-2
SPX3819M5-L-3-1 SPX3819S-L-1-5
SPX3819M5-L-3-3 SPX3819S-L-1-8
SPX3819M5-L-5-0 SPX3819S-L-2-5
SPX3819R2-L-3-3 SPX3819T-L-1-8
SPX3819R2-L-5-0 SPX3819T-L-3-0
SPX5205M5-L
SPX5205M5-L-1-2
SPX5205M5-L-1-5
SPX5205M5-L-1-8
SPX5205M5-L-2-0
SPX5205M5-L-2-5
SPX5205M5-L-2-8
SPX5205M5-L-3-0
SPX5205M5-L-3-3
SPX5205M5-L-5-0
SPX3819S
SPX3819T-L-3-1
SPX3819T-L-3-3
SPX3819U
SPX3819S-1-8
SPX3819S-2-5
SPX3819S-3-0
SPX3819U-1-8
SPX3819U-2-5
SPX3819U-3-0
SPX3819U-3-1
SPX3819U-3-3
SPX3819U-5-0
SPX3819U5-3-3
SPX3819U5-L-3-3
SPX3819U-L
SPX3819R2
SPX3819R2-1-2
SPX3819S-L-3-0
SPX3819S-L-3-1
SPX3819U-L-1-8
SPX3819U-L-2-5
Page 6 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
Appendix A
Characterization Data Histograms
Page 7 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vref@1ma
20
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Vref (v)
Silan SPX5205 - Vref@1ma
30
25
20
15
10
5
cold
room
hot
0
Vref (v)
Page 8 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vref@150ma
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Vref (v)
Silan SPX5205 - Vref@150ma
30
25
20
15
10
5
cold
room
hot
0
Vref (v)
Page 9 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5202 - Load Reg
14
12
10
8
cold
room
hot
6
4
2
0
LoadReg (%)
Silan SPX5202 - Load Reg
16
14
12
10
8
cold
room
hot
6
4
2
0
LoadReg (%)
Page 10 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vout@ Vin=16v
16
14
12
10
8
cold
room
hot
6
4
2
0
Vout (v)
Silan SPX5205 - Vout@ Vin=16v
30
25
20
15
10
5
cold
room
hot
0
Vout (v)
Page 11 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vout @ Ven=16v
16
14
12
10
8
cold
room
hot
6
4
2
0
Vout (v)
Silan SPX5205 - Vout @ Ven=16v
30
25
20
15
10
5
cold
room
hot
0
Vout (v)
Page 12 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - LineReg
25
20
15
10
5
cold
room
hot
0
Line Reg (%/v)
Silan SPX5205 - LineReg
20
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Line Reg (%/v)
Page 13 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vdropout@100ua
35
30
25
20
15
10
5
cold
room
hot
0
Vdropout (v)
Silan SPX5205 - Vdropout@100ua
35
30
25
20
15
10
5
cold
room
hot
0
Vdropout (v)
Page 14 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Vdrop@150ma
35
30
25
20
15
10
5
cold
room
hot
0
Vdrop (v)
Silan SPX5205 - Vdrop@150ma
35
30
25
20
15
10
5
cold
room
hot
0
Vdrop (v)
Page 15 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Ien_Hi
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Ien (ua)
Silan SPX5205 - Ien_Hi
20
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Ien (ua)
Page 16 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Ien_Lo
16
14
12
10
8
cold
room
hot
6
4
2
0
Ien (ua)
Silan SPX5205 - Ien_Lo
20
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Ien (ua)
Page 17 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Quiescent_I
35
30
25
20
15
10
5
cold
room
hot
0
Iq (ua)
Silan SPX5205 - Quiescent_I
35
30
25
20
15
10
5
cold
room
hot
0
Iq (ua)
Page 18 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Ignd@100ua
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Ignd (ua)
Silan SPX5205 - Ignd@100ua
20
18
16
14
12
10
8
cold
room
hot
6
4
2
0
Ignd (ua)
Page 19 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Ignd@150ma
35
30
25
20
15
10
5
cold
room
hot
0
Ignd (ma)
Silan SPX5205 - Ignd@150ma
35
30
25
20
15
10
5
cold
room
hot
0
Ignd (ma)
Page 20 of 21
11/17/2006
SPX5205
Product Family
Characterization Report
HV SPX5205 - Current Limit
35
30
25
20
15
10
5
cold
room
hot
0
Current Limit
Silan SPX5205 - Current Limit
35
30
25
20
15
10
5
cold
room
hot
0
Current Limit
Page 21 of 21
11/17/2006
Reliability and Qualification Report
Silan BP4 Process Reliability Qualification
using the SPX29150
Prepared By: Salvador Wu & Greg West
QA Engineering
Reviewed By: Fred Claussen
VP Quality & Reliability
Date: September 15, 2006
Date: September 15, 2006
SPX29150 Reliability Report
Page 1 of 4
Table Of Contents
Title Page
1
2
2
2
2
2
3
3
4
4
4
5
4
Table Of Contents
Device Description
Pin Out
Manufacturing Information
Package Information
Reliability Test Summary
Life Test Data
FIT Data Calculations
MTBF Data Calculations
ESD Testing
Early Life Failure Rate Testing
5L TO-263 Pb Free Package Qualification Addendum
Device Description:
The SPX29150/51/52/53 are 1.5A, highly accurate voltage regulators with a low dropout
voltage of 390mV (typical) @ 1.5A. These regulators are specifically designed for low
voltage applications that require a low dropout voltage and a fast transient response. They
are fully fault protected against over-current, reverse battery, and positive and negative
voltage transients. On-chip trimming adjusts the reference voltage to 1% initial accuracy.
Other features in the 5 pin versions include Enable and Error Flag.
The SPX29150/51/52/53 is offered in 3-pin and 5-pin TO-220 & TO-263 packages. For a
3A version, refer to the SPX29300 data sheet.
PIN OUT SPX29150
Manufacturing Information:
Product:
SPX29150
Description: 1.5A PNP LDO
Mask Set: MS1562
Lot Number(s): SPXBP4012EC,
A135428.3 (15), A136411.2 (16)
Process:
sil-bp4
Wafer Fab: Silan
Package Information:
Package Type: TO 263-5L
Package Code:: JEDEC
SPX29150 Reliability Report
Page 2 of 4
Reliability Qualification Test Summary:
Stress Level Device
Lot Number Burn-In Temp Sample Size No. Fail
168Hrs
168Hrs
168Hrs
1000Hrs
1000Hrs
1000Hrs
SPX29150 SPXBP401
77
77
77
77
77
77
0
0
0
0
0
0
125 °C
125 °C
125 °C
125 °C
125 °C
125 °C
2EC
SPX29150 A135428.3
(15)
SPX29150 A136411.2
(16)
SPX29150 SPXBP401
2EC
SPX29150 A135428.3
(15)
SPX29150 A136411.2
(16)
Life Test
Life testing is conducted to determine if there are any fundamental reliability related
failure mechanism(s) present in the device.
These failure mechanisms can be divided roughly into four groups:
1. Process or die related failures such as oxide defects, metallization defects, and
diffusion defects.
2. Assembly related failures such as chip mount defects, wire bond defects, molding
defects, and trim/form/singulation defects.
3. Design related defects.
4. Miscellaneous, undetermined, or application induced failures.
125C Operating Life Test Results
As part of the Sipex design qualification program, the Product/Reliability Engineering
group subjected 231 parts to 168 hours and 1000 hours of 125° C life stress testing.
168 Hour Timepoint
The 231 parts were subjected to the life test profile and completed the stress with no
failures.
1000 Hour Timepoint
231 parts were reintroduced to life stress testing, completing the 1000 hour HTOL time
point without any failures or significant shifts in process parameters
FIT Rate Calculations
FIT rate (failures in time) is the predicted number of failures per billion device hours.
This predicted value is based upon,
SPX29150 Reliability Report
Page 3 of 4
• The Life Test conditions summarized in the HTOL table (time/temperature, device
quantity, failure quantity).
• The Activation Energy (Ea) for potential failure modes. The weighted Activation
Energy(Ea) of observed failure mechanisms for Sipex products has been determined
to be 0.8eV.
Based on the above criteria SPX29150 product FIT rates for 25°, 55°, and 70°C of
operation at 60% and 90% confidence levels have been calculated and listed below.
FIT Failure Rates: SPX29150 BP4 Silan Process
Confidence Level
+25°C
1.6
+55°C
26.4
64.2
+70°C
89.0
216.0
60%
90%
3.9
1 FIT = 1 Failure per Billion Device-Hours
MTBF Calculation: SPX29150 BP4 Silan Process
Confidence Level
+25°C
+55°C
+70°C
60%
90%
6.15E+08
2.53E+08
3.78E+07
1.56E+07
1.12E+07
4.63E+06
ESD Testing
Human Body Model ESD – 32 units were subjected to Human Body Model ESD testing
at +/- 2KV. All units passed.
Early Life Failure Rate Testing
Early Life Test – 600 units were subject to Early Life test for 48 Hours. All units passed
Additional Reliability Tests
77 of the units were placed on Unbiased HAST testing, 77 of the units were placed on Thermal
Shock testing, and 77 on -65C/+150C Temperature Cycle testing. All units passed testing as summarized
in the following table.
# of
Test
Condition
Time
Sample Size
rejects
TEMP. Cycles
-65C/+150C
500 Cycles
96hrs
77
77
0
0
HAST Unbiased
130C/85%RH
Thermal Shock
-65C/+150C
500 Cycles
77
0
SPX29150 Reliability Report
Page 4 of 4
相关型号:
SPX3819S-ADJ
Adjustable Positive LDO Regulator, 1.24V Min, 15V Max, 0.7V Dropout, BIPolar, PDSO8, SOIC-8
SIPEX
©2020 ICPDF网 联系我们和版权申明