BD70H36G-2C [ROHM]
罗姆的监测用IC采用CMOS工艺,实现了高精度、超低消耗电流。为保证客户可根据应用进行选择,备有Nch漏极开路输出(BD70Hxx-xC)系列和CMOS输出(BD73Hxx-2C)系列产品。没有滞后宽度,检测解除电压设定为与检测电压相同的值。;型号: | BD70H36G-2C |
厂家: | ROHM |
描述: | 罗姆的监测用IC采用CMOS工艺,实现了高精度、超低消耗电流。为保证客户可根据应用进行选择,备有Nch漏极开路输出(BD70Hxx-xC)系列和CMOS输出(BD73Hxx-2C)系列产品。没有滞后宽度,检测解除电压设定为与检测电压相同的值。 |
文件: | 总20页 (文件大小:1295K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Nano EnergyTM
Datasheet
Voltage Detector (Reset) IC Series for Automotive Application
Supervisory IC
BD70Hxx-xC Series BD73Hxx-2C Series
General Description
Key Specifications
ROHM's Supervisory ICs are highly accurate, with ultra-
low current consumption feature that uses CMOS
process. The lineup includes N-channel open drain
output (BD70Hxx-xC) and CMOS output (BD73Hxx-2C)
so that the users can select depending on the application.
Because there is no hysteresis, the Release Voltage is
set to same value of Detection Voltage.
◼ Release Voltage:
3.76 V, 3.66 V, 3.56 V, 3.46 V, 3.06 V, 1.20V
◼ Ultra-Low Current Consumption:
270 nA (Typ)
-40 °C to +125 °C
◼ Operation Temperature Range:
Special Characteristics
◼ Release Voltage Accuracy:
±50 mV (-40 °C to +125 °C)
Features
◼ AEC-Q100 Qualified (Note 1)
◼ No Hysteresis
Package
W (Typ) x D (Typ) x H (Max)
2.90 mm x 2.80 mm x 1.25 mm
SSOP5:
◼ Two Output Types
(Nch Open Drain and CMOS Output)
◼ Nano Energy
◼ Very Small, Lightweight and Thin Package
◼ Package SSOP5 is similar to SOT-23-5 (JEDEC)
(Note 1) Grade 1
Application
All automotive devices that requires voltage detection
Typical Application Circuits
VDD1
VDD2
VDD1
RL
Microcontroller
RST
Microcontroller
RST
BD70Hxx-xC
BD73Hxx-2C
CVDD
CVDD
(Noise-reduction
Capacitor)
(Noise-reduction
Capacitor)
CL
CL
GND
GND
Figure 1. Open Drain Output Type
BD70Hxx-xC Series
Figure 2. CMOS Output Type
BD73Hxx-2C Series
Pin Configuration
SSOP5
TOP VIEW
N.C.
N.C.
VOUT VDD GND
Pin Description
SSOP5
PIN NAME
PIN No.
Function
Output pin
1
2
3
4
5
VOUT
VDD
GND
N.C.
Power supply voltage
GND
No connection pin
No connection pin
The no connection pin is electrically open and
can be connected to either VDD or GND.
N.C.
Nano Energy™ is a trademark or a registered trademark of ROHM Co., Ltd.
○Product structure:Silicon integrated circuit ○This product has no designed protection against radioactive rays
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
1/17
BD70Hxx-xC Series BD73Hxx-2C Series
Block Diagrams
VDD
VOUT
Vref
(Note)
(Note)
GND
(Note) Parasitic Diode
Figure 3. BD70Hxx-xC Series
(Note)
VDD
Vref
VOUT
(Note)
(Note)
GND
(Note) Parasitic Diode
Figure 4. BD73Hxx-2C Series
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
2/17
BD70Hxx-xC Series BD73Hxx-2C Series
Ordering Information
B
D
7
x
H
x
G
-
x
C
T
R
x
Package
G: SSOP5
Part
Output Type
Output Logic Release Voltage
Product Rank
C: for Automotive Specification
TR: Embossed tape and reel
Packing and Forming
Number 0: ch
Open Drain
3: CMOS
H: Active
High
38: 3.76 V
37: 3.66 V
36: 3.56 V
35: 3.46 V
31: 3.06 V
12: 1.20 V
Process Code
Lineup
Output Type
Open Drain
Part Number
CMOS
Part Number
Release Voltage
Marking
9E
Marking
3.76 V
3.66 V
3.56 V
3.46 V
3.06 V
1.20 V
BD70H38G-2CTR
BD70H37G-2CTR
BD70H36G-2CTR
BD70H35G-2CTR
BD70H31G-CTR
BD70H12G-2CTR
5P
5Q
5R
5S
-
BD73H38G-2CTR
9F
5M
5N
9N
dh
BD73H37G-2CTR
BD73H36G-2CTR
BD73H35G-2CTR
-
-
-
Marking Diagram
SSOP5 (TOP VIEW)
Part Number Marking
LOT Number
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
3/17
BD70Hxx-xC Series BD73Hxx-2C Series
Absolute Maximum Ratings (Ta = 25 °C)
Parameter
Symbol
Limit
-0.3 to +7
Unit
V
Power Supply Voltage
VDD - GND
Nch Open Drain Output
Output Voltage
GND - 0.3 to +7
GND - 0.3 to VDD + 0.3
70
VOUT
V
CMOS Output
Output Current
Maximum Junction Temperature
IO
Tjmax
mA
°C
+150
Storage Temperature Range
Tstg
-55 to +150
°C
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the
properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal resistance taken into consideration by increasing
board size and copper area so as not to exceed the maximum junction temperature rating.
Thermal Resistance (Note 1)
Thermal Resistance (Typ)
Parameter
Symbol
Unit
1s (Note 3)
2s2p (Note 4)
SSOP5
Junction to Ambient
Junction to Top Characterization Parameter (Note 2)
θJA
376.5
40
185.4
30
°C/W
°C/W
ΨJT
(Note 1) Based on JESD51-2A (Still-Air).
(Note 2) The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside
surface of the component package.
(Note 3) Using a PCB board based on JESD51-3.
(Note 4) Using a PCB board based on JESD51-7.
Layer Number of
Measurement Board
Material
FR-4
Board Size
Single
114.3 mm x 76.2 mm x 1.57 mmt
Top
Copper Pattern
Thickness
70 μm
Footprints and Traces
Layer Number of
Measurement Board
Material
FR-4
Board Size
114.3 mm x 76.2 mm x 1.6 mmt
2 Internal Layers
4 Layers
Top
Copper Pattern
Bottom
Copper Pattern
74.2 mm x 74.2 mm
Thickness
70 μm
Copper Pattern
Thickness
35 μm
Thickness
70 μm
Footprints and Traces
74.2 mm x 74.2 mm
Recommended Operating Conditions
Parameter
Symbol
Topr
Min
-40
Typ
+25
Max
Unit
°C
Operating Temperature
+125
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
4/17
BD70Hxx-xC Series BD73Hxx-2C Series
Electrical Characteristics (Unless otherwise specified Ta = -40 °C to +125 °C, VDD = 0.8 V to 6.0 V)
Limit
Typ
Parameter
Symbol
Condition
Unit
Min
3.72
3.71
3.62
3.61
3.52
3.51
3.42
3.41
3.02
3.01
1.16
1.15
-
Max
3.80
3.81
3.70
3.71
3.60
3.61
3.50
3.51
3.10
3.11
1.24
1.25
1.50
1.60
-
BD70H38G-2C,
BD73H38G-2C
BD70H37G-2C,
BD73H37G-2C
BD70H36G-2C,
BD73H36G-2C
BD70H35G-2C,
BD73H35G-2C
Ta = -30 to +70 °C
3.76
Ta = -40 to +125 °C
Ta = -30 to +70 °C
Ta = -40 to +125 °C
Ta = -30 to +70 °C
Ta = -40 to +125 °C
Ta = -30 to +70 °C
Ta = -40 to +125 °C
Ta = -30 to +70 °C
Ta = -40 to +125 °C
Ta = -30 to +70 °C
Ta = -40 to +125 °C
3.66
3.56
3.46
3.06
1.20
Release Voltage
VR
V
BD70H31G-C
BD70H12G-2C
Circuit Current when ON
Circuit Current when OFF
Minimum Operating Voltage
IDD1
IDD2
VDD = VR - 0.2 V
VDD = VR + 0.5 V
0.27
0.30
-
-
-
µA
µA
V
-
VOPL VOL ≤ 0.4 V, RL = 100 kΩ (Note 1)
VDD = 4.0 V, ISOURCE = 4.0 mA
VOH
0.80
VDD - 0.4
VDD - 0.4
-
-
“High” Output Voltage (Pch)
V
VDD = 6.0 V, ISOURCE = 2.5 mA
VDD = 0.8 V, ISINK = 0.17 mA,
VR = 1.2V
-
-
-
-
0.4
0.4
VDD = 1.2 V, ISINK = 1.0 mA,
VOL
“Low” Output Voltage (Nch)
V
VR = 3.06V to 3.76V
VDD = 2.4 V, ISINK = 2.0 mA,
VR = 3.06V to 3.76V
ILEAK VDD = VDS = 6 V
-
-
-
-
0.4
1.0
200
Output Leak Curent (BD70Hxx-xC)
µA
µs
VOUT = VDD → 50 %,
tPHL
Delay Time (H → L)
20
50
RL = 100 kΩ (Note 1) (Note 2)
VOUT = GND → 50 %,
tPLH
Delay Time (L → H)
15
40
100
µs
RL = 100 kΩ (Note 1) (Note 2)
(Note 1) RL: Pull-up resistor connected between VOUT and power supply.
(Note 2) tPLH: VDD = (VR - 0.5 V) → (VR + 0.5 V)
tPHL: VDD = (VR + 0.5 V) → (VR - 0.5 V)
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
5/17
BD70Hxx-xC Series BD73Hxx-2C Series
Typical Performance Curves
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
BD70H38G-2C
BD70H38G-2C
VDD = VR + 0.5 V
Ta = +125 °C
Ta = +70 °C
Ta = +25 °C
VDD = VR - 0.2 V
Ta = -30 °C
Ta = -40 °C
-40 -25 -10
5
20 35 50 65 80 95 110 125
0
1
2
3
4
5
6
Temperature: Ta [°C]
Power Supply Voltage: VDD [V]
Figure 5. Circuit Current vs Power Supply Voltage
Figure 6. Circuit Current vs Temperature
6.0
5.0
4.0
3.0
2.0
1.0
0.0
3.85
3.80
3.75
3.70
3.65
BD70H38G-2C
BD70H38G-2C
3.5
3.6
3.7
3.8
3.9
4.0
-40 -25 -10
5
20 35 50 65 80 95 110 125
Power Supply Voltage: VDD [V]
Temperature: Ta [°C]
Figure 8. Release Voltage vs Temperature
Figure 7. Release Voltage vs Power Supply Voltage
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
6/17
BD70Hxx-xC Series BD73Hxx-2C Series
Typical Performance Curves - continued
6.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
BD70H38G-2C
5.0
Ta = +125 °C
Ta = +70 °C
4.0
Ta = +25 °C
Ta = -30 °C
3.0
Ta = -40 °C
Ta = +125 °C
Ta = +70 °C
2.0
Ta = +25 °C
Ta = -30 °C
1.0
Ta = -40 °C
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
Power Supply Voltage: VDD [V]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
Power Supply Voltage: VDD [V]
Figure 10. I/O Characteristics
Figure 9. I/O Characteristics
(VOUT Pull-up to VDD, RL = 100 kΩ)
(VOUT Pull-up to 5 V, RL = 100 kΩ)
1.0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
BD70H38G-2C
0.9
BD70H38G-2C
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature: Ta [°C]
Temperature: Ta [°C]
Figure 12. Minimum Operating Voltage vs Temperature
(VOUT Pull-up to VDD, RL = 100 kΩ)
Figure 11. Minimum Operating Voltage vs Temperature
(VOUT Pull-up to 5 V, RL = 100 kΩ)
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
7/17
BD70Hxx-xC Series BD73Hxx-2C Series
Typical Performance Curves - continued
70
70
60
50
40
30
20
10
0
60
VDD = 4.8 V
VDD = 2.0 V
50
VDD = 1.8 V
40
VDD = 4.0 V
30
VDD = 1.2 V
20
10
VDD = 0.8 V
BD70H38G-2C
BD73H35G-2C
0
0.0
0.5
1.0
1.5
2.0
2.5
0
1
2
3
4
5
6
Drain-Source Voltage: VDS [V]
Drain-Source Voltage: VDS [V]
Figure 14. “Low” Output Current vs Drain-Source Voltage
Figure 13. “High” Output Current vs Drain-Source Voltage
140
35
BD73H35G-2C
BD70H38G-2C
Ta = -40 °C
120
30
Ta = -30 °C
Ta = -30 °C
Ta = -40 °C
100
25
Ta = +25 °C
80
20
15
60
Ta = +125 °C
Ta = +70 °C
40
10
Ta = +70 °C
Ta = +25 °C
20
5
Ta = +125 °C
0
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
3.5
4
4.5
5
5.5
6
Power Supply Voltage: VDD [V]
Power Supply Voltage: VDD [V]
Figure 15. “High” Output Current vs Power Supply Voltage
(VDS = 0.5 V)
Figure 16. “Low” Output Current vs Power Supply Voltage
(VDS = 0.5 V)
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
8/17
BD70Hxx-xC Series BD73Hxx-2C Series
Typical Performance Curves - continued
70
100
90
80
70
60
50
40
30
20
10
0
BD70H38G-2C
BD70H38G-2C
60
50
40
30
20
10
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature: Ta [°C]
Temperature: Ta [°C]
Figure 17. Output Delay Time (L → H) vs Temperature
Figure 18. Output Delay Time (H → L) vs Temperature
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
9/17
BD70Hxx-xC Series BD73Hxx-2C Series
Application Information
Operation Description
Consider the release voltage is same as the threshold voltage. When the voltage applied to VDD reaches the respective
threshold voltage, VOUT level will change from "H" to "L" and from “L" to "H". Since the output pattern in BD70Hxx-xC is an
open-drain system, a pull-up resistor has to be connected to VDD or other power supply.
(The output (VOUT) “H” voltage in this case becomes VDD or other power supply voltage.)
Timing Waveform
The following shows the relationship between the input voltage VDD and the output voltage VOUT when the power supply
voltage VDD is swept up and swept down.
VDD
RL
VDD
Vref
VOUT
CVDD
CL
GND
Figure 19. BD70Hxx-xC Set-up
VDD
VR
VOPL: < 0.8 V
t
1
2
3
4
5
2
3
4
5
2
1
VOUT
t
undefined
undefined
tPLH
tPHL
tPLH
tPHL
Figure 20. Timing Diagram
Operating Conditions Explanation
1. When the power supply turns on, the Output Voltage (VOUT) becomes unstable until VDD exceeds the Minimum
Operating Voltage (VOPL).
2. VOUT changes to “L”. However, this change depends on the VOUT rise time when the power supply starts up, so thorough
confirmation is required.
3. When VDD exceeds the Release Voltage (VR), delay time (tPLH) happens, then VOUT switches from “L” to “H”.
4. VOUT keeps “H”.
5. When VDD drops below Release Voltage (VR), delay time (tPHL) happens, then VOUT switches from “H” to “L”.
Since this IC does not have hysteresis width, when VDD fluctuates near VR, VOUT switches repeatedly with “H” → “L” → “H”
→ “L”. As a counter measure, it is recommended to use capacitor (CVDD). Perform sufficient evaluation before deciding the
capacitor value since the capacitance needs to be adjusted according to the amount of power supply voltage fluctuation.
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
10/17
BD70Hxx-xC Series BD73Hxx-2C Series
Application Information – continued
Bypass Capacitor for Noise Rejection
For the stable operation of the IC, put capacitor between the VDD and GND pin and connect it closer to the pin as possible.
When using extremely big capacitors, the transient response speed becomes slow so please thoroughly check.
External Parameters
The recommended value of pull-up resistance value is 50 kΩ to 1 MΩ. Since the changes are brought by many factors
(circuit configuration, board layout, etc.) when using, ensure that confirmation of the real function was carried out.
In addition, this IC has high impedance design. So depending on the condition of use, this may be affected by small leak
current due to the uncleanness of PCB surface. For example, if a 10 MΩ leakage is assumed between the VOUT and GND
pin, it is recommended to set the value of pull up resistor less than or equal to 1/10 of the impedance of assumed leakage
route.
Behavior at less than the Operating Voltage Limit
When VDD falls less than the minimum operating voltage, output will be undefined. When output is connected to pull-up
voltage, output will be equivalent to pull-up voltage.
Precautions when Steep Power Supply Rise
In case of a steep power supply rise, the output may toggle to “High” once like as shown in Figure 21. This is due to the
undefined output when the supply is less than the minimum operating voltage of the IC. When this waveform affects the
application, make the rise time slower by attaching capacitor to VDD (CVDD). As a reference value, the recommended VDD
Rise Time is 200 μs or more.
VDD
VR
VOPL: <0.8 V
t
VOUT
t
Figure 21. Steep Power upply Rise Response
www.rohm.com
TSZ02201-0GIG2G300030-1-2
© 2017 ROHM Co., Ltd. All rights reserved.
11/17
TSZ22111 • 15 • 001
28.Jun.2021 Rev.004
BD70Hxx-xC Series BD73Hxx-2C Series
Application Examples
(1) Examples of common application circuits
Application examples of BD70Hxx-xC series (Open
drain output type) and BD73Hxx-2C series (CMOS
output type) are shown below.
VDD1
VDD2
RL
CASE1: If the power supply of the microcontroller (VDD2
)
differs from the power supply of the detection (VDD1), use
the load resistance RL connected to VDD2 in the output of
open drain output type (BD70Hxx-xC series) as shown
in Figure 22.
Microcontroller
RST
BD70Hxx-xC
CVDD
CL
Figure 22. Open Drain Output Type
GND
CASE2: If the power supply of the microcontroller is the
same as the power supply of the detection (VDD1), use it
in CMOS output type (BD73Hxx-2C series) as shown in
Figure 23.
VDD1
Microcontroller
Otherwise, use the RL connected to VDD1 in open drain
output type (BD70Hxx-xC series).
RST
BD73Hxx-2C
CVDD
When connecting a capacitor CL for noise elimination
and for setting the output delay time to the VOUT pin
(reset signal input pin of microcontroller), the waveform
is dull during rising and falling of the output so use after
confirmation that there is no problem.
CL
Figure 23. CMOS Output Type
GND
(2) The following is an example of an OR connection between two types of detection voltage resets the microcontroller.
VDD1
VDD2
VDD3
RL
Microcontroller
RST
BD70Hxx-xC
No.1
BD70Hxx-xC
No.2
CVDD
CVDD
CL
GND
Figure 24. OR Circuit Connection Application
There are multiple power supply in the system, and in case monitoring for each independent power supply VDD1 and VDD2
and reset of micro-controller is required, an application where output “H” voltage is aligned to the microcontroller power
supply VDD3 is possible by connecting OR application and pull-up at random voltage (VDD3) such as shown in Figure 24.
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
12/17
BD70Hxx-xC Series BD73Hxx-2C Series
Application Examples – continued
(3) Examples of the power supply with resistor dividers
In some applications, the power supply voltage of an IC comes from a resistor divider circuit. An inrush current will flow into
the circuit when the output level switches from “Low” to “High” or vice versa. Inrush current is a sudden surge of current that
flows from the power supply (VDD) to ground (GND) as the output logic changes its state. This current flow may cause
malfunction in the systems operation such as output oscillations, etc.
V1
IDD
RA
IDD
VDD
Inrush Current
RL
RB
BD70Hxx-xC
VOUT
CVDD
GND
CL
VDD
Figure 26. Current Consumption vs VDD Voltage
0
VR
Figure 25. Resistor Divider Connection Application
A voltage drop [Inrush current (IDD)] x [input resistor (RA)] is caused by the inrush current when the output switches from
"L"→"H", and causes the input voltage to drop. When the input voltage drops and falls below the release voltage, the output
will switch from "H"→"L". At this time, the inrush current stops flowing through at output “L”, and the voltage drop disappears.
As a result, the output switches from "L"→"H", which again causes the inrush current to flow and the voltage to drop. This
operation repeats and leads to oscillation.
In case resistor divider is not use and only use RA, same response will happen.
(Attention)
Since there is no hysteresis width, it is not advisable to use it in circuit that connects the resistance to the input side. When
using it, set the circuit configuration and constants in the actual application after a thorough evaluation is carried out.
250
225
200
175
150
125
100
75
250
225
200
175
150
125
100
75
BD73H35G-2C
BD70H38G-2C
50
50
25
25
0
0
4.0
4.5
5.0
5.5
6.0
4.0
4.5
5.0
5.5
6.0
Supply Voltage High: VDDH [V]
Supply Voltage High: VDDH [V]
Figure 28. CMOS Output Inrush Current
(VDD = 1 V → VDDH, Ta = 25 °C)
Figure 27. Open Drain Output Inrush Current
(VOUT Pull-up to VDD, RL = 100 kΩ, VDD = 1 V → VDDH, Ta = 25 °C)
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
13/17
BD70Hxx-xC Series BD73Hxx-2C Series
Considerations on Input and Output Capacitor
It is suggested to use input and output capacitors which is positioned as near as possible to the pins. The capacitor between
the input pin and GND is effective when the power supply impedance increases or when the wiring is long. A large capacitor
at the output improves stability and output load characteristics. Before implementation, check the state of mounting. In
addition, the ceramic capacitor deviates in general and has temperature characteristics and AC bias characteristics.
Furthermore, depending on the usage, the capacitance value decreases over time. It is recommended that ceramic capacitor
to use is decided after gathering detailed data information by consulting brand manufacturers.
10 V withstand voltage
B1characteristics
GRM188B11A105KA61D
10
0
10 V withstand voltage
B characteristics
-10
6.3 V withstand voltage
B characteristics
-20
-30
10 V withstand voltage
-40
F characteristics
-50
-60
4 V withstand voltage
X6S characteristics
-70
-80
-90
-100
0
1
2
3
4
DC Bias Voltage [V]
Figure 29. Ceramic Capacitance Change - DC Bias Properties
(Characteristic example)
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
14/17
BD70Hxx-xC Series BD73Hxx-2C Series
Operational Notes
1. Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
2. Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at
all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic
capacitors.
3. Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4. Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5. Recommended Operating Conditions
The function and operation of the IC are guaranteed within the range specified by the recommended operating
conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical
characteristics.
6. Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.
Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing
of connections.
7. Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
8. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
9. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
10. Regarding the Input Pin of the IC
In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation
of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage.
Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower
than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when no power supply
voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have voltages
within the values specified in the electrical characteristics of this IC.
11. Ceramic Capacitor
When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
www.rohm.com
TSZ02201-0GIG2G300030-1-2
© 2017 ROHM Co., Ltd. All rights reserved.
15/17
TSZ22111 • 15 • 001
28.Jun.2021 Rev.004
BD70Hxx-xC Series BD73Hxx-2C Series
Physical Dimension and Packing Information
Package Name
SSOP5
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
16/17
BD70Hxx-xC Series BD73Hxx-2C Series
Revision History
Date
Revision
Changes
2017/10/12
2018/04/03
001
002
New Release
Format change
Format change, added notation of “Nano Energy”,
added BD70H31G-C in the lineup
2019/11/05
2021/06/28
003
004
Added BD70H12G-2C in the lineup
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GIG2G300030-1-2
28.Jun.2021 Rev.004
17/17
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
BD70H37G-2C
罗姆的监测用IC采用CMOS工艺,实现了高精度、超低消耗电流。为保证客户可根据应用进行选择,备有Nch漏极开路输出(BD70Hxx-xC)系列和CMOS输出(BD73Hxx-2C)系列产品。没有滞后宽度,检测解除电压设定为与检测电压相同的值。
ROHM
BD70H38G-2C
罗姆的监测用IC采用CMOS工艺,实现了高精度、超低消耗电流。为保证客户可根据应用进行选择,备有Nch漏极开路输出(BD70Hxx-xC)系列和CMOS输出(BD73Hxx-2C)系列产品。没有滞后宽度,检测解除电压设定为与检测电压相同的值。
ROHM
BD70HA3MEFJ-M
BDxxHA3MEFJ-M系列是可提供0.3A输出电流的稳压器。输出精度为±1%。有可使用外接电阻在1.5V~7.0V范围内任意设置输出电压的可变型以及1.5V/1.8V/2.5V/3.0V/3.3V/5V/6V/7V固定输出型两种。封装组件采用散热性优良的HTSOP-J8。本机型内置用于防止因输出短路等发生IC破坏的过电流保护电路、关断时使电路电流为0µA的ON/OFF开关、以及防止因过负荷状态等使IC发生热破坏的温度保护电路。另外,采用了陶瓷电容器,有助于整机的小型化和长寿化。
ROHM
BD70HA3VEFJ-M (新产品)
BDxxHA3VEFJ-M is a LDO regulator with output current 0.3A. The output accuracy is ±1% of output vo
ROHM
©2020 ICPDF网 联系我们和版权申明