BD83A14MUF-M (开发中) [ROHM]
This IC is a white LED driver for LCD backlight. It has 4ch current drivers for LED drive, making it ideal for high brightness LED drive. LED pin maximum voltage is 50V, making it suitable for driving medium LCD panels. The dimming is controlled by the PWM signal and can be set up to 20,000: 1@100Hz. It also supports analog dimming and can accommodate even higher brightness ranges by combining with PWM dimming. DC/DC converters can be controlled for boost applications, and the input operating voltage range is 4.5V to 48.0V.;型号: | BD83A14MUF-M (开发中) |
厂家: | ROHM |
描述: | This IC is a white LED driver for LCD backlight. It has 4ch current drivers for LED drive, making it ideal for high brightness LED drive. LED pin maximum voltage is 50V, making it suitable for driving medium LCD panels. The dimming is controlled by the PWM signal and can be set up to 20,000: 1@100Hz. It also supports analog dimming and can accommodate even higher brightness ranges by combining with PWM dimming. DC/DC converters can be controlled for boost applications, and the input operating voltage range is 4.5V to 48.0V. CD |
文件: | 总50页 (文件大小:2225K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
4 ch Current Driver Integrated, Built-in MOS for Boost DC/DC Controller
White LED Driver for Automotive
BD83A14EFV-M BD83A14MUF-M
Key Specifications
◼ Input Operating Voltage Range:
General Description
This IC is a white LED driver for LCD backlight.
4.5 V to 48.0 V
◼ Output LED Current Absolute Accuracy:
±5.0 %@80.1 mA
It has 4 ch current drivers for LED drive, making it ideal for
high brightness LED drive. LED pin maximum voltage is 50
V, making it suitable for driving medium LCD panels.
The dimming is controlled by the PWM signal and can be
set up to 20,000: 1@100 Hz. It also supports analog
dimming and can accommodate even higher brightness
ranges by combining with PWM dimming. DC/DC
converters can be controlled for boost applications, and the
input operating voltage range is 4.5 V to 48.0 V.
Ta = -40 °C to +125 °C
200 kHz to 2420 kHz
-40 °C to +125 °C
150 mA / ch
◼ DC/DC Oscillation Frequency:
◼ Operating Temperature:
◼ LED Maximum Current:
◼ LED Maximum Dimming Ratio:
20,000: 1@100 Hz
◼ LED1 to LED4 Pin Maximum Voltage:
50 V
Packages
HTSSOP-B24
W (Typ) x D (Typ) x H (Max)
7.8 mm x 7.6 mm x 1.0 mm
4.0 mm x 4.0 mm x 1.0 mm
Features
◼ AEC-Q100 Qualified(Note 1)
VQFN24FV4040
◼ Functional Safety Supportive Automotive Products
◼ Built-in 4 ch Current Driver for LED Driver
◼ Current Mode Boost DC/DC Converter
◼ Load Switch (M1) Control Pin
◼ DC Dimming Function by Pulse Input
◼ PWM Dimming
(20,000: 1@100 Hz, 100 Hz to 25 kHz)
◼ Spread Spectrum Function
HTSSOP-B24
BD83A14EFV-M
VQFN24FV4040
BD83A14MUF-M
◼ DC/DC Converter Oscillation Frequency External
Synchronization Function
Applications
◼ LSI Protect Functions (UVLO, OVP, TSD, OCP)
◼ LED Anode/Cathode Short Circuit Protection Function
◼ Automotive CID (Center Information Display) Panel
◼ Navigation
◼ LED Open/Short Protection Function
◼ Cluster Panel
◼ HUD (Head Up Display)
(Note 1) Grade 1
◼ Other Small and Medium Sized LCD Panel for
Automotive
Typical Application Circuit
VCC
CVCC
RCSH
VREG
1
2
24
23
22
21
20
19
18
17
16
15
14
13
REG
VCC
CSH
CREG
M1
D1
GND
EN
VOUT
EN
PWM
3
LDSW
N.C.
L1
RG
CIN
COUT
4
PWM
SYNC
ADIM_P
COMP
RT
M2
SYNC
5
OUTL
CSL
ADIM_P
6
CCOMP RCOMP
EXP-PAD
RCSL
7
PGND
PLSET
FAIL
ROVP2
ROVP1
RRT
8
CPLSET
RISET
RFAIL
9
ISET
LGND
LED1
LED2
VREG
VFAIL
10
11
12
OVP
LED4
LED3
Figure 1. Boost Application Circuit Diagram
〇Product structure : Silicon integrated circuit 〇This product has no designed protection against radioactive rays.
○This product is protected by U.S. Patent No.7,235,954, No.7,541,785 and No.7,944,189.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
1/47
BD83A14EFV-M BD83A14MUF-M
Contents
General Description........................................................................................................................................................................1
Features..........................................................................................................................................................................................1
Key Specifications ..........................................................................................................................................................................1
Packages........................................................................................................................................................................................1
Applications ....................................................................................................................................................................................1
Typical Application Circuit ...............................................................................................................................................................1
Contents .........................................................................................................................................................................................2
Pin Configurations ..........................................................................................................................................................................3
Pin Descriptions..............................................................................................................................................................................3
Block Diagram ................................................................................................................................................................................5
Description of Blocks ......................................................................................................................................................................6
Absolute Maximum Ratings ..........................................................................................................................................................10
Thermal Resistance......................................................................................................................................................................10
Recommended Operating Conditions...........................................................................................................................................11
Operating Conditions (External Constant Range).........................................................................................................................11
Electrical Characteristics...............................................................................................................................................................12
Typical Performance Curves.........................................................................................................................................................15
Function Descriptions ...................................................................................................................................................................17
PCB Application Circuit Diagram ..................................................................................................................................................28
List of External Components.........................................................................................................................................................29
Selection of Components Externally Connected...........................................................................................................................31
Precautions for PCB Layout..........................................................................................................................................................37
Power Consumption Calculation Example....................................................................................................................................38
Application Circuit Example ..........................................................................................................................................................40
I/O Equivalence Circuit .................................................................................................................................................................41
Operational Notes.........................................................................................................................................................................42
Ordering Information.....................................................................................................................................................................44
Marking Diagrams.........................................................................................................................................................................44
Physical Dimension and Packing Information...............................................................................................................................45
Revision History............................................................................................................................................................................47
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
2/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Pin Configurations
(TOP VIEW)
(TOP VIEW)
1
2
24
23
22
21
20
19
18
17
16
15
14
13
REG
GND
VCC
24
23
22
21
20
19
CSH
3
1
2
3
4
5
6
18
17
16
15
14
13
PWM
SYNC
LDSW
OUTL
CSL
EN
LDSW
N.C.
4
PWM
SYNC
ADIM_P
COMP
RT
5
OUTL
CSL
ADIM_P
COMP
6
EXP-PAD
EXP-PAD
7
PGND
PLSET
FAIL
OVP
PGND
PLSET
FAIL
8
RT
9
ISET
ISET
10
11
12
LGND
LED1
LED2
LED4
LED3
7
8
9
10
11
12
BD83A14EFV-M
BD83A14MUF-M
Pin Descriptions
Pin No.
Signal Type
Pin Name
Function
(Note 1)
EFV MUF
Internal reference voltage: Used as the reference voltage for the internal circuit. 5 V is
generated and output by setting the EN pin to High. Connect a capacitance of 2.2 μF for
phase compensation.
1
22
REG
A
Small signal ground: Use this for the ground of external components connected to the
REG, RT, COMP, ADIM_P, ISET, PLSET, OVP, and VCC pins.
2
3
4
23
24
1
GND
EN
A
I
Enable input: The EN pin is turned High to activate the internal circuit. The internal circuit
stops and the standby state is set by setting to Low.
PWM dimming signal: The LED current can be controlled according to On Duty of the
input PWM signal.
PWM
I
External synchronization frequency input / SSCG setting: The internal oscillation
frequency can be externally synchronized by inputting an external clock signal to the
SYNC pin before the Self Diagnosis is completed. When using spread spectrum mode
(SSCG), short the SYNC pin and the REG pin beforehand.
5
2
SYNC
I
DC dimming setting: The ISET pin voltage can be changed by On Duty of the pulse
signal input to the ADIM_P pin. When using only PWM dimming, short the ADIM_P pin
with the REG pin.
6
7
8
3
4
5
ADIM_P
COMP
RT
I
Phase compensating capacitor connection: The reference voltage and LED pin voltage
generated by REF Voltage block are compared and output by Error AMP. Connect a filter
for phase compensation.
A
A
Resistor connection for oscillation frequency setting: The oscillation frequency (fOSC
of DC/DC converter can be set by connecting a resistor (RRT) between the RT pin and the
GND pin.
)
Resistor connection for LED current setting: LED current (ILED) can be set by
connecting a resistor (RISET) between the ISET pin and the GND pin.
9
6
7
8
9
ISET
LGND
LED1
LED2
LED3
LED4
A
P
P
P
P
P
Large current ground 1: GND of the current driver (the LED1, LED2, LED3, and LED4
pins).
10
11
12
LED cathode connection 1: Open drain output of the current driver ch 1 for LED drive.
Connect to the LED cathode.
LED cathode connection 2: Open drain output of the current driver ch 2 for LED drive.
Connect to the LED cathode.
LED cathode connection 3: Open drain output of the current driver ch 3 for LED drive.
Connect to the LED cathode.
13 10
LED cathode connection 4: Open drain output of the current driver ch 4 for LED drive.
Connect to the LED cathode.
14 11
(Note 1) A: Sensitive signal such as detect and reference, I: Input signal from other units, O: Output signal to other units, P: Large current signal susceptible to
impedance, including transient current.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
3/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Pin Descriptions – continued
Pin No.
Signal Type
Pin Name
Function
(Note 1)
EFV MUF
Overvoltage protection and short circuit protection detection : When OVP pin voltage
rises to 1.21 V or more, the overvoltage protection (OVP) is activated, and DC/DC
converters are switched OFF. If OVP pin voltage is 0.1 V or less for 3.56 ms, Short Circuit
Protection (SCP) is activated, and both DC/DC converter and the current driver are turned
OFF.
15 12
OVP
FAIL
A
Error output flag: Outputs the status of protective operation from the FAIL pin. Since this
pin is an open drain output, use a resistor to pull it up to the REG pin, etc.
16 13
O
Switching pulse number setting: Pulse addition function is provided to stabilize DC/DC
converter output voltage even when PWM Duty is low. The number of switching pulses to
be added can be set by the capacitance value connected between the PLSET pin and the
GND pin.
17 14 PLSET
A
P
A
18 15
19 16
PGND
CSL
Large current ground 2: Use it for external parts connected to the OUTL pin.
Overcurrent protection detection input: The current flowing through the Low side FET
(M2) is voltage-converted by the overcurrent detection resistor (RCSL) and detected by the
CSL pin. When overcurrent protection (OCPL) is activated, it turns off DC / DC converter
switching.
Low side FET gate signal: The switching signal output of the DC/DC converter. Connect
20 17
21 21
OUTL
N.C.
P
-
the OUTL pin to the gate of the Low side FET (M2).(Note 2)
Not connected internally.
Output for driving the load switch gate: The signal output for driving the gate of the load
switch. When the input overcurrent protection is activated, the load switch is turned OFF
as LDSW pin voltage = VCC pin voltage.(Note 2)
22 18
23 19
LDSW
CSH
P
A
Input current detection input: The input current is converted to voltage by the input
current detection resistor (RCSH) connected between the VCC-CSH pin and detected by
the CSH pin. Turns the load switch OFF when the input overcurrent protection is activated.
Power supply voltage input: The input operating voltage range is 4.5 V to 48.0 V, but
when the IC is started, start it with VCC ≥ 5.5 V. The decoupling capacitor (CVCC) between
the VCC pin and the GND pin should be as close to the IC pin as possible.
24 20
VCC
P
-
EXP-
PAD
-
The EXP-PAD should be connected to the board ground.
(Note 1) A: Sensitive signal such as detect and reference, I: Input signal from other units, O: Output signal to other units, P: Large current signal susceptible to
impedance, including transient current.
(Note 2) The MUF package requires external components to prevent adjacent short between the OUTL pin and the LDSW pin. If concerned, consider the EFV
package.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
4/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Block Diagram
VCC
CSH
LDSW
EN
LDSW
Driver
VREF
PROTECT
REG
PROTECT
Additional
Pulse
Pre Driver
REG
PLSET
RT
DC/DC
Control
LOGIC
OSC
SLOPE
+
-
OUTL
PGND
CSL
SSCG
PWM
COMP
SYNC
COMP
Error
AMP
-
-
LED1
LED2
LED3
LED4
Soft
Start
LDSW
Driver
+
Minimum
Channel
Selector
PROTECT
UVLO
DC/DC
Control
LOGIC
ꢀꢀꢀꢀꢀꢀꢀFAIL
TSD
SCP
OCPH
ISET SCP
FAIL
OCPL
OVP
OPEN Det
SHORT Det
OVP
Current
Driver
Internal
CLK
REF
Voltage
Dimming
Control
PWM
REG
PULSE-
DC
ADIM_P
ISET
CH1 CH2 CH3 CH4
ISET
Current Driver
GND
LGND
Figure 2. Internal Block Diagram
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
5/47
BD83A14EFV-M BD83A14MUF-M
Description of Blocks
Unless otherwise stated, the value in the sentence is the typical value.
1 VREF
Internal reference voltage circuit. By setting the EN pin to High, 5 V is generated and output to the REG pin. REG voltage
is used as the power supply for the internal circuit. Also, this is used to fix each input pin to High voltage outside the IC.
Connect REG capacitance (CREG = 2.2 μF) to the REG pin for the phase compensation. Note that if CREG is not connected,
unstable operation such as oscillation will occur.
2 LDSW Driver
Input overcurrent protection circuit. If the voltage between the VCC-CSH pin is 0.1 V or more and continues for 10 μs or
more, the input overcurrent protection is activated, and the load switch (M1) is turned OFF as LDSW pin voltage = VCC
pin voltage. Then, after 56.96 ms elapses, the load switch is turned ON. At this time, if the voltage between the VCC-CSH
pin is 0.1 V or more, the load switch is turned OFF again. If the voltage between the VCC-CSH pin is less than 0.1 V, Self
Diagnosis is performed and restarted. When the input overcurrent protection is detected, the FAIL pin goes Low. The VCC-
LDSW pin is connected by a 3 MΩ resistor inside the IC. Do not connect a resistor between the VCC-LDSW pin because
connecting a resistor between the VCC-LDSW pin outside the IC may prevent the load switch from being turned ON.
When the VCC pin voltage is turned ON setting the EN pin to Low, the voltage between the VCC-LDSW pins may open
momentarily and an inrush current may flow depending on the VCC startup speed and the type of load switch used. Be
sure to check with the actual application.
3 OSC (Oscillator)
Oscillation frequency generator. The oscillation frequency (fOSC) of DC/DC converter can be set by connecting a resistor
for oscillation frequency setting (RRT) between the RT pin and ground. In addition, the oscillation frequency of DC/DC
converter can be externally synchronized by inputting the external synchronization frequency (fSYNC) to the SYNC pin.
4 SSCG (Spread Spectrum Clock Generator)
Spread spectrum circuit. The spread spectrum function (SSCG) is activated by shorting the SYNC pin and the REG pin.
Noise peaks can be reduced by periodically changing the oscillation frequency by SSCG. The fluctuation range of the
frequency due to SSCG is from 100 % to 92 % of the set oscillation frequency. The oscillation frequency fluctuation period
is 2.3 kHz.
5 SLOPE
This circuit generates a saw wave that serves as the source of the switching pulse of DC/DC converter. SLOPE output
signal and COMP pin voltage are compared, and a switching pulse is generated.
6 Minimum Channel Selector
Selector circuit for detecting LED pin voltages. Selects the lowest pin voltage among LED1 to LED4 pin voltages and inputs
it in Error AMP.
7 Error AMP (Error Amplifier)
This is an error amplifier that takes LED control voltage and the smallest value of the LED1 to LED4 pin voltages as input.
Phase compensation can be set by connecting a resistor and a capacitor to the COMP pin.
8 Soft Start
Soft start circuit for DC/DC converters. This function is used to suppress a steep increase in the inductor current at startup
and an overshoot in the output voltage. Controls the change in switching Duty by limiting the rising edge of the output of
Error AMP (COMP pin voltage) with the soft start function.
9 PWM COMP (PWM Comparator)
This comparator compares COMP pin voltage, which is the output of Error AMP, with SLOPE output signal. Controls the
Duty of the switching pulse of DC/DC converter.
10 Additional Pulse
This circuit adds switching pulses of DC/DC converter. With the pulse addition function, the LED current can be supplied
stably even when the PWM dimming ratio decreases.
11 DC/DC Control LOGIC
This circuit generates the logic of the Low side FET gate signal output from the OUTL pin.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
6/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Description of Blocks - continued
12 Pre Driver
This is the drive circuit for the Low side FET gate signal output from the OUTL pin.
13 Internal CLK
This circuit generates the internal reference clock. It is a clock of 2.3 MHz and used as a counter.
14 Dimming Control
This circuit controls the dimming rate during PWM dimming.
15 Current Driver / ISET
Current driver circuit for lighting LED. LED current can be set by connecting a resistor to the ISET pin.
In addition, the LED current can be set by the On Duty input signal of the ADIM_P pin.
16 PULSE-DC
This block smooths the pulse input to the ADIM_P pin and outputs the DC voltage to the ISET block.
The DC voltage level can be set by the pulse input Duty of the ADIM_P pin.
17 PROTECT
Outputs the status of protective operation from the FAIL pin. Since this pin is an open drain output, connect it to the REG
pin with a resistor. If the status of protective operation is not monitored, turn the FAIL pin to OPEN or connect to the GND
pin.
17.1 UVLO (Under Voltage Lock Out)
Under Voltage Lock Out. When VCC pin voltage is 4.10 V or less or REG pin voltage is 3.95 V or less, Under
Voltage Lockout (UVLO) is activated, and the load switch (M1), DC/DC switching, and current driver turn OFF.
When VCC pin voltage is 4.25 V or more and REG pin voltage is 4.10 V or more, UVLO is released and the IC
restarts from Self Diagnosis. When UVLO is detected, output of the FAIL pin does not change. When the FAIL pin
is pulled up to REG pin, FAIL pin voltage will also drop as REG pin voltage is decreased.
17.2 TSDLED (Thermal Shutdown for Current Driver)
This is a temperature protection circuit that monitors the vicinity of the current driver on the chip. Prevents chip
temperature from rising due to output current fault. When the chip temperature rises to 175 °C or more, the
temperature protection circuit (TSDLED) is activated, the load switch (M1), DC/DC switching, and current driver
are turned OFF. When TSDLED is detected, the FAIL pin goes Low. When the chip temperature falls 150 °C or
less, TSDLED is released, the IC restarts from Self Diagnosis.
17.3 TSDREG (Thermal Shutdown for REG)
This is a temperature protection circuit that monitors the vicinity of the REG pin on the chip. Prevents chip
temperature rising due to the REG pin failure. When the chip temperature rises to 175 °C or more, the temperature
protection circuit (TSDREG) is activated, and REG pin voltage, load switch (M1), DC/DC switching, and current
driver turn OFF. When TSDREG is detected, the FAIL pin goes Low. When the chip temperature falls 150 °C or
less, TSDREG is released and the IC restarts from Self Diagnosis.
17.4 OCPL (Over Current Protection for Low side)
The current flowing through the Low side FET (M2) is detected by the overcurrent detection resistor (RCSL), and
when the CSL pin voltage becomes 0.3 V or more, the overcurrent protection (OCPL) is activated and the
switching of the DC/DC converter is stopped. When the CSL pin voltage drops below 0.3 V, OCPL is released and
switching resumes. When OCPL is detected, the output of the FAIL pin does not change.
17.5 OVP (Over Voltage Protection)
Output overvoltage protection circuit. When OVP pin voltage (resistor division of DC/DC converter output voltage)
becomes to 1.21 V or more, the overvoltage protection circuit (OVP) activates and only DC/DC switching is
stopped. When OVP pin voltage falls 1.16 V or less, OVP is released. When OVP is detected, the output of the
FAIL pin goes Low.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
7/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
17 PROTECT – continued
17.6 OPEN Det (LED Open Detection)
LED open protection circuit. When any of LED1 to LED4 pin voltages is 0.3 V or less and OVP pin voltage is 1.21
V or more, LED open protection (OPEN Det) is activated, and the current driver is latched OFF only for the LED
row that is open. OPEN Det is released when VEN = Low or UVLO is detected. When OPEN Det is detected, the
FAIL pin goes Low.
17.7 SHORT Det (LED Short Detection)
LED short protection circuit. When LED pin voltage is 5 V or more for 3.56 ms (counter), LED short protection
(SHORT Det) is activated, and the current driver is latched OFF only for the corresponding LED row. However,
the counter is reset when LED pin voltage does not satisfy the detection condition prior to SHORT Det being
activated. SHORT Det is released when VEN = Low or UVLO is detected. Since the 3.56 ms counter is counted up
only when PWM = High, the time until SHORT Det is detected varies depending on PWM Duty. When SHORT
Det is detected, the FAIL pin goes Low. SHORT Det can be detected when the PWM pulse width is 20 μs (Min) or
more.
17.8 SCP (Short Circuit Protection)
Short Circuit Protection circuit. If any of the LED1 to LED4 pin voltages are 0.3 V or less or OVP pin voltage is 0.1
V or less for 3.56 ms (counter), the Short Circuit Protection (SCP) is activated, and the load switch (M1), DC/DC
switching, and current driver turn OFF. However, the counter is reset when each pin voltage does not satisfy the
condition prior to SCP being activated. The SCP is released when VEN = Low or UVLO is detected. When SCP is
detected, the FAIL pin goes Low.
17.9 OCPH (Over Current Protection for High side) / LDSW Driver
Input overcurrent protection circuit. If a condition in which the voltage between the VCC-CSH pins is 0.1 V or more
continues for 10 μs or more, the input overcurrent protection (OCPH) is activated. It becomes LDSW pin voltage
= VCC pin voltage and the load switch (M1), DC/DC switching, and current driver turn OFF. Then, after 56.96 ms
(counter) elapses, the load switch is turned ON. At this time, if the voltage between the VCC-CSH pins is 0.1 V or
more, the load switch, DC/DC switching, and current driver are turned OFF again. Also, if the voltage between the
VCC-CSH pins is less than 0.1 V, Self Diagnosis is performed and restarted. When OCPH is detected, the FAIL
pin goes Low.
17.10 ISET Pin Fault (ISET-GND Short Protection)
ISET pin fault protection circuit. When the resistance value connected to the ISET pin falls 3.5 kΩ or less (when
ADIM_P pin voltage = REG pin voltage), ISET pin fault protection is activated, and the load switch (M1), DC/DC
switching, and current driver are turned OFF. If the resistance value connected to the ISET pin is more than 3.5
kΩ (when ADIM_P pin voltage = REG pin voltage), ISET pin fault protection is released, and the load switch,
DC/DC switching, and current driver are turned ON. When ISET pin fault is detected, the FAIL pin goes Low.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
8/47
BD83A14EFV-M BD83A14MUF-M
Description of Blocks – continued
Detect Conditions and Operation at Detection of Each Protection Function (All values in the table are Typ values)
Operation at Detection
Protection
Function
Detect Condition
No.
1
Load
DC/DC
Switch Switching
Current
Driver
FAIL
[Detect]
[Release]
(Block Name)
Under Voltage
Lockout
VCC ≤ 4.10 V
or
VCC ≥ 4.25 V
and
High
(Note 5)
OFF
OFF
OFF
OFF
OFF
OFF
(UVLO)
VREG ≤ 3.95 V
VREG ≥ 4.10 V
Thermal
2
3
Shutdown LED
(TSDLED)
Tj ≥ 175 °C
Tj ≥ 175 °C
Tj ≤ 150 °C
Tj ≤ 150 °C
Low
Low
Thermal
OFF
OFF
Shutdown REG
(TSDREG)
OFF
Overcurrent
Protection
(OCPL)
High
(Note 5)
4
5
VCSL ≥ 0.3 V
VCSL < 0.3 V
ON
ON
OFF
OFF
ON
ON
Overvoltage
Protection
(OVP)
VOVP ≥ 1.21 V
VOVP ≤ 1.16 V
Low
Only
detection
LED pin
is OFF
Only
LED Open
Protection
(OPEN Det)
VLEDn(Note 1) ≤ 0.3 V
and
VEN = Low(Note 6)
or
Latch
Low
6
7
ON
ON
ON
ON
VOVP ≥ 1.21 V
Detects UVLO
LED Short
Protection
Detects
VEN = Low(Note 6)
or
detection
LED pin
is OFF
Latch
Low
VLEDn(Note 1) ≥ 5.0 V
for 3.56 ms or more(Note 2)
(SHORT Det)
Detects UVLO
Detects
VLEDn(Note 1) ≤ 0.3 V
or
Short Circuit
Protection
(SCP)(Note 3)
VEN = Low(Note 6)
or
Latch
Low
8
9
OFF
OFF
OFF
VOVP ≤ 0.1 V
Detects UVLO
for 3.56 ms or more
Detects
Input
Voltage between the VCC-
Overcurrent
Protection
(OCPH)(Note 3)
voltage between the VCC-
CSH pin ≥ 0.1 V
for 10 μs or more
CSH pin < 0.1 V
OFF
OFF
OFF
OFF
OFF
OFF
Low
Low
(Note 4)
ISET resistor
> 3.5 kΩ
ISET-GND
ISET resistor ≤ 3.5 kΩ
(when ADIM_P pin voltage
= REG pin voltage)
10 Short Protection
(ISET Pin Fault)
(when ADIM_P pin voltage
= REG pin voltage)
(Note 1) LEDn indicates one of the LED1 to LED4 pins.
(Note 2) LED pin voltage of at least 1 channel shall be less than VLEDCTL(MIN) x 1.2. When LED pin voltages of all channels are 2.4 V or more, the LED short protection
does not operate. Since the 3.56 ms counter is counted up only when PWM = High, the time until SHORT Det is detected varies depending on PWM Duty.
(Note 3) When Short Circuit Protection (SCP) and Input Overcurrent Protection (OCPH) are detected at the same time, the operation of Input Overcurrent Protection
takes precedence.
(Note 4) When 56.96 ms elapses after the load switch is turned OFF, the load switch turns ON. At this time, when the voltage between the VCC-CSH pins ≥ 0.1 V,
the load switch, DC/DC switching, and current driver are turned OFF again. Also, when the voltage between the VCC-CSH pins < 0.1 V, Self Diagnosis is
performed and restarted.
(Note 5) When pulled up to any voltage, it becomes High output.
(Note 6) The Low width of EN pin need 10 µs or more.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
9/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Absolute Maximum Ratings (Ta = 25 °C)
Parameter
Symbol
VCC, VLDSW, VCSH
Rating
Unit
V
VCC, LDSW, CSH Pin Voltage
-0.3 to +50.0
-0.3 to +7.0
-0.3 to +50.0
-0.3 to VREG
-0.3 to +7.0
-55 to +150
150
Voltage Between VCC-LDSW, VCC-CSH Pins
VCC-VLDSW, VCC-VCSH
VLED1, VLED2, VLED3, VLED4, VOVP
VRT, VCOMP, VISET, VPLSET, VOUTL, VCSL
VEN, VREG, VSYNC, VPWM, VADIM_P, VFAIL
Tstg
V
LED1, LED2, LED3, LED4, OVP Pin Voltage
RT, COMP, ISET, PLSET, OUTL, CSL Pin Voltage
EN, REG, SYNC, PWM, ADIM_P, FAIL Pin Voltage
Storage Temperature Range
V
V
V
°C
Maximum Junction Temperature
Tjmax
°C
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the
properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal resistance taken into consideration by increasing
board size and copper area so as not to exceed the maximum junction temperature rating.
Thermal Resistance(Note 1)
Thermal Resistance (Typ)
Parameter
Symbol
Unit
1s(Note 3)
2s2p(Note 4)
HTSSOP-B24
Junction to Ambient
Junction to Top Characterization Parameter(Note 2)
θJA
96.0
12.0
34.9
9.0
°C/W
°C/W
ΨJT
VQFN24FV4040
Junction to Ambient
Junction to Top Characterization Parameter(Note 2)
θJA
116.5
15
36.2
8
°C/W
°C/W
ΨJT
(Note 1) Based on JESD51-2A (Still-Air). The BD83A14EFV-M chip and the BD83A14MUF-M chip are used.
(Note 2) The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside
surface of the component package.
(Note 3) Using a PCB board based on JESD51-3.
(Note 4) Using a PCB board based on JESD51-5, 7.
Layer Number of
Measurement Board
Material
FR-4
Board Size
Single
114.3 mm x 76.2 mm x 1.57 mmt
Top
Copper Pattern
Thickness
70 μm
Footprints and Traces
Layer Number of
Measurement Board
Thermal Via(Note 5)
Material
FR-4
Board Size
114.3 mm x 76.2 mm x 1.6 mmt
2 Internal Layers
Pitch
Diameter
4 Layers
1.20 mm
Φ0.30 mm
Top
Copper Pattern
Bottom
Thickness
70 μm
Copper Pattern
Thickness
35 μm
Copper Pattern
Thickness
70 μm
Footprints and Traces
74.2 mm x 74.2 mm
74.2 mm x 74.2 mm
(Note 5) This thermal via connect with the copper pattern of layers 1,2, and 4. The placement and dimensions obey a land pattern.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
10/47
BD83A14EFV-M BD83A14MUF-M
Recommended Operating Conditions
Operating Range
Parameter
Symbol
Unit
Min
4.5
Max
48.0
Power Supply Voltage(Note 1)
VCC
fOSC
V
DC/DC Oscillation Frequency Range
(SSCG = OFF)
200
2420
kHz
PWM Frequency Range(Note 2)
fPWM
0.1
40
18
25.0
400
100
kHz
kHz
%
ADIM_P pin Input Frequency Range(Note 3)
ADIM_P pin Input On Duty Range(Note 3)
fADIM_P
DADIM_P
Higher of
Lower of
External Synchronized Frequency Range(Note 4)
fSYNC
kHz
200 or fOSC x 0.9
700 or fOSC x 1.1
External Synchronized Pulse Duty Range(Note 5)
LED Current Setting Range(Note 6)
Operating Temperature
DSYNC
ILED
40
20
60
%
mA
°C
150
Topr
-40
+125
(Note 1) When IC is started, the voltage must be UVLO release voltage or more. Therefore, consider the power supply drop caused by the parasitic resistor
and start the IC at VCC ≥ 5.5 V.
VCC(Min) = 4.5 V is the minimum value of VCC that can operate the IC alone. The minimum value of power supply voltage that can be set depends on
the connected LED load and external components.
(Note 2) Generally, flickering of LEDs is easier to see when the dimming frequency is set lower than 100 Hz. Set after confirming with the actual device evaluation.
(Note 3) If you input a frequency outside the operating range to the ADIM_P pin, the LED flicker will be more visible. Set after confirming with the actual device
evaluation.
(Note 4) When the external synchronization function is not used, connect the SYNC pin to VREG (SSCG = ON) or GND (SSCG = OFF).
(Note 5) When using the external synchronization function, switching from the external synchronization state to the internal oscillation frequency is not possible
during stable operation.
(Note 6) The amount of current per channel that can be set by the resistor (RISET) connected to the ISET pin ( DADIM_P = 100 % ). Set the LED current so that the
maximum junction temperature (Tjmax) is not exceeded.
Operating Conditions (External Constant Range)
Operating Range
Parameter
Symbol
Unit
Min
1.0(Note 7)
8.8
Typ
Max
4.7
53.0
45
REG Capacitance
CREG
RISET
RRT
2.2
μF
kΩ
kΩ
nF
μF
μF
μF
Resistor for LED Current Setting
Resistor for Oscillation Frequency Setting
PLSET Capacitance
-
-
-
-
-
-
4
CPLSET
CVCC
-
10
Input Capacitance 1
1(Note 7)
10(Note 7)
20(Note 7)
-
(Note 8)
Input Capacitance 2
CINVCC
-
Output Capacitance
COUT
100
(Note 7) Set the capacitance so that it does not fall below the minimum value in consideration of temperature characteristics, DC bias characteristics, etc.
(Note 8) CINVCC means the total capacitance of CIN and CVCC
.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
11/47
BD83A14EFV-M BD83A14MUF-M
Electrical Characteristics
(Unless otherwise specified, VCC = 12 V, Ta = -40 °C to +125 °C)
Standard Value
Unit
mA
Conditions
Parameter
Symbol
Min
Typ
Max
10
VEN = 5 V, VSYNC = 0 V,
VPWM = 0 V, CIN = 10 μF,
RT = OPEN, ISET = OPEN,
Circuit Current
ICC
-
-
VADIM_P = VREG
,
Resistance between
LEDn-GND = 10 kΩ
Standby Current
[VREF]
IST
-
0
10
μA
V
VEN = Low
REG Output Voltage
[DC/DC Converter]
VREG
4.7
5.0
5.3
IREG = -5 mA, CREG = 2.2 μF
OUTL Pin ON Resistor
(High side)
RONLH
RONLL
1.5
1.0
3.0
2.0
6.0
4.0
Ω
Ω
IOUTL = -10 mA
IOUTL = 10 mA
OUTL Pin ON Resistor
(Low side)
RISET = 8.8 kΩ,
VADIM_P = VREG
RISET = 15.1 kΩ,
VCOMP = 1.0 V,
VLED = 1.5 V,
LED Control Voltage
VLEDCTL
0.84
1.03
1.22
V
COMP Sink Current
ICOMPSINK
150
220
290
μA
VADIM_P = VREG
RISET = 15.1 kΩ,
VCOMP = 1.0 V,
VLED = 0 V,
COMP Source Current
ICOMPSOURCE
-290
-220
-150
μA
VADIM_P = VREG
Oscillation Frequency 1
Max Duty 1
fOSC1
DUTY_MAX1
fOSC2
270
95
300
-
330
-
kHz
%
RRT = 33.3 kΩ
RRT = 33.3 kΩ
RRT = 4 kΩ
Oscillation Frequency 2
PLSET Charge Current
PLSET Set Voltage
1980
35
2200
50
2420
65
kHz
μA
V
IPLSET
VPLSET = 0 V
VPLSET
0.4
0.5
0.6
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
12/47
BD83A14EFV-M BD83A14MUF-M
Electrical Characteristics – continued
(Unless otherwise specified, VCC = 12 V, Ta = -40 °C to +125 °C)
Standard Value
Parameter
[Current Driver]
Symbol
Unit
Conditions
Min
Typ
Max
RISET = 15.1 kΩ,
mA
%
LED Current Absolute Variation
ILEDn
76.1
0
80.1
84.1
VADIM_P = VREG
RISET = 15.1 kΩ,
VADIM_P = VREG
LED Current Relative Variation
(Note 1)
ILEDREL
RISETLIM
tPWMMIN
-
3.5
-
5
-
ISET-GND Short Protection
Resistor
-
kΩ
μs
VADIM_P = VREG
PWM Dimming Minimum Pulse
Width
fPWM = 100 Hz to 25 kHz,
ILED = 80.1 mA
0.5
-
PWM Dimming Frequency
PWM Low Section Detect Time
[Logic Input (EN)]
fPWM
0.1
-
25.0
35.6
kHz
ms
tPWML
21.4
28.5
Input High Voltage
VINH1
VINL1
RIN1
2.1
-
-
-
-
V
V
Input Low Voltage
0.5
150
Input Resistor
50
100
kΩ
VEN = 5 V
[Logic Input (PWM, SYNC, ADIM_P)]
Input High Voltage
Input Low Voltage
Input Resistor
VINH2
2.1
-
-
-
-
V
V
VINL2
RIN2
0.5
150
50
100
kΩ
VPWM = VSYNC = VADIM_P = 5 V
(Note 1) ILEDREL = (ILEDn(MAX) – ILEDn(MIN)) / ILEDn(AVE) x 100
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
13/47
BD83A14EFV-M BD83A14MUF-M
Electrical Characteristics – continued
(Unless otherwise specified, VCC = 12 V, Ta = -40 °C to +125 °C)
Standard Value
Parameter
[PROTECT]
Symbol
Unit
Conditions
Min
Typ
Max
VCCUVLO Detect Voltage
VCCUVLO Release Voltage
REGUVLO Detect Voltage
REGUVLO Release Voltage
OVP Detect Voltage
VUVLOVCC1
VUVLOVCC2
VUVLOREG1
VUVLOREG2
VOVPDET
3.90
4.05
3.75
3.90
1.173
4.10
4.25
3.95
4.10
1.210
4.30
4.45
4.15
4.30
1.247
V
V
V
V
V
VCC = Sweep down
VCC = Sweep up
VREG = Sweep down
VREG = Sweep up
VOVP = Sweep up
OVP Detect Voltage
Hysteresis Width
VOVPHYS
-
50
-
mV
VOVP = Sweep down
Input OCP Detect Voltage
VOCPH
VLDSW
ICSH
80
4.4
100
5.4
120
6.4
mV
V
VCC-VCSH = Sweep up
VCSH = VCC
VCC-VLDSW
LDSW Operation Voltage
at Input OCP Release
CSH Pin Input Current
OCPL Detect Voltage
VCSH = 12 V
-0.8
0.27
0.0
+0.8
0.33
μA
V
VOCPL
0.30
VCSL = Sweep Up
LED Open Protection Detect
Voltage
VLED = Sweep down
VOVP ≥ VOVPDET
VOPEN
VSCP1
VSCP2
0.25
0.05
0.25
0.30
0.10
0.30
0.35
0.15
0.35
V
V
V
LED Anode SCP Detect Voltage
VOVP = Sweep down
VLED = Sweep down
LED Cathode SCP Detect
Voltage
LED Anode SCP Detect
Delay Time
tSCP1
tSCP2
2.67
2.67
4.7
3.56
3.56
5.0
4.45
4.45
5.3
ms
ms
V
LED Cathode SCP Detect
Delay Time
LED Short Protection Detect
Voltage
VSHORT
VLED = Sweep up
Initial Check Time
tINICK
RFAIL
5.34
-
7.12
1.0
8.90
2.0
ms
kΩ
FAIL Pin ON Resistor
IFAIL = 1 mA
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
14/47
BD83A14EFV-M BD83A14MUF-M
Typical Performance Curves
(Reference data, unless otherwise specified VCC = 12 V)
10
8
5.3
5.2
5.1
5.0
4.9
4.8
4.7
6
4
2
0
4
15
26
37
48
-40 -20
0
20 40 60 80 100 120
Power Supply Voltage : VCC [V]
Temperture : Ta [°C]
Figure 3. Circuit Current vs Power Supply Voltage
Figure 4. REG Output Voltage vs Temperature
330
320
310
300
290
280
270
2420
2376
2332
2288
2244
2200
2156
2112
2068
2024
1980
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
Temperature : Ta [°C]
Temperature : Ta [°C]
Figure 5. Oscillation Frequency 1 vs Temperature
(RRT = 33.3 kΩ)
Figure 6. Oscillation Frequency 2 vs Temperature
(RRT = 4 kΩ)
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
15/47
BD83A14EFV-M BD83A14MUF-M
Typical Performance Curves – continued
(Reference Data)
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
84
83
82
81
80
79
78
77
76
0.0
-40 -20
0
20 40 60 80 100 120
20 30 40 50 60 70 80 90 100110120130140150
LED Current : ILED [mA]
Temperture : Ta [°C]
Figure 7. LED Control Voltage vs LED Current
Figure 8. LED Current vs Temperature
100
90
80
70
60
50
100
90
80
70
60
50
8
10
12
14
16
8
10
12
14
16
Power Supply Voltage : VCC [V]
Power Supply Voltage : VCC [V]
Figure 9. Efficiency 1 vs Power Supply Voltage
(RRT = 33.3 kΩ, RISET = 15.1 kΩ,
Figure 10. Efficiency 2 vs Power Supply Voltage
(RRT = 4 kΩ, RISET = 15.1 kΩ,
Number of LED Series = 10, Number of LED Parallels = 4)
Number of LED Series = 10, Number of LED Parallels = 4)
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
16/47
BD83A14EFV-M BD83A14MUF-M
Function Descriptions
Unless otherwise stated, the value in the sentence is the Typ value.
1 Current Driver
This model has a built-in 4 ch current driver. The LED current setting range per channel is 20 mA to 150 mA, and the LED
current can be adjusted by the resistance value between the ISET pin and GND.
1.1 How to Set LED Current
1.4 PWM Low Section Detect Function
1.2 When Using Analog Dimming
1.3 When Using PWM Dimming
1.5 LED Pin Handling of Unused Channels
1.6 When Setting the LED Current Above 150 mA
1.1 How to Set LED Current
The LED current ILED can be calculated using the following equation.
푉
푅
10 × ꢂꢃ6
[mA]
ꢀ푆ꢁ푇
Resistance Value Setting Example (VADIM_P
VREG
=
퐼퐿퐸퐷
=
×
9
ꢀ푆ꢁ푇
)
ISET Resistor [kΩ]
LED Current [mA]
퐼퐿퐸퐷: Output current per channel (LED current)
(Recommended operating condition:
20 mA to 150 mA)
53.0
30.0
15.1
8.8
22.8
40.3
ꢄꢅꢆ퐸ꢇ: ISET pin voltage 1.089 V
80.1
(When ADIM_P pin voltage VADIM_P = VREG
ꢈꢅꢆ퐸ꢇ: Resistor for LED current setting
(Recommended operating condition:
8.8 kΩ to 53 kΩ)
)
137.5
When RISET ≤ 3.5 kΩ, ISET pin short protection detect is
activated and, output of the LED current is stopped.
150
140
130
120
110
100
90
80
70
60
50
40
30
20
9
13
17
21
25
29
33
37
41
45
49
53
RISET [kΩ]
Figure 11. ILED vs RISET (VADIM_P = VREG
)
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
17/47
BD83A14EFV-M BD83A14MUF-M
1 Current Driver – continued
1.2 When Using Analog Dimming
ISET pin voltage can be adjusted according to the input Duty to the ADIM_P pin. The LED current ILED can be calculated
from the following equation as described above.
푉
푅
10 × ꢂꢃ6
[mA]
ꢀ푆ꢁ푇
퐼퐿퐸퐷
=
×
9
ꢀ푆ꢁ푇
However, VISET can be adjusted according to ADIM_P
pin input On Duty DADIM_P as follows:
퐼퐿퐸퐷: Output current per channel (LED current)
(Recommended operating condition:
20 mA to 150 mA)
ꢈꢅꢆ퐸ꢇ: Resistor for LED current setting
(Recommended operating condition:
8.8 kΩ to 53 kΩ)
ꢊ퐴퐷ꢅ푀_푃: ADIM_P pin input On Duty
(Recommended operating condition:
18 % to 100 %)
ꢄ
= ꢂ.ꢃ8ꢉ [V]
ꢅꢆ퐸ꢇ
(90 % ≤ DADIM_P ≤ 100 %)
ꢄ
= ꢂ.ꢃ8ꢉ × 10 × ꢊ퐴퐷ꢅ푀_푃 [V]
ꢅꢆ퐸ꢇ
(18 % < DADIM_P < 90 %)
9
Note : Note that the LED current set by RISET and the ADIM_P pin cannot be set less than 10 mA
100
90
80
70
60
50
40
30
20
10
0
18
28
39
49
59
69
80
90
100
ADIM_P Input Duty : DADIM_P [%]
Figure 12. ILED vs DADIM_P (RISET = 15.1 kΩ)
1.3 When Using PWM Dimming
The LED current can be controlled according to On Duty of the PWM signal input to the PWM pin. However, in the region
where the ON time of the LED current is less than 0.5 μs or the OFF time is less than 0.5 μs, the pulse time is shorter than
PWM dimming minimum pulse width, so it cannot be used regularly. It is okay to use this region transiently, so it is also
possible to set PWM Duty = 0 % and 100 %.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
18/47
BD83A14EFV-M BD83A14MUF-M
1 Current Driver – continued
1.4 PWM Low Section Detect Function
Counting starts when PWM = High is switched to Low in the VEN = High state. When PWM Low section reaches 28.5 ms,
the operation is regarded as OFF state. After that, when PWM input is turned High, switching operation (pre-boost) is
restarted.
1.5 LED Pin Handling of Unused Channels
VOUT
This model has four built-in constant current circuits.
The current can be supplied to the LED by setting the
PWM pin to High, and the LED current can be set by
inserting a resistor between the ISET pin and GND. The
LED current that can be supplied per row is 20 mA to
150 mA.
Pull down the LED pin of the unused channel to GND
with 10 kΩ.
10 kΩ
LED4
LED3
LED2
LED1
Figure 13. When Setting LED4 Unused
1.6 When Setting the LED Current Above 150 mA
The LED1 to LED4 pins can be used in bundles.
For example, as shown in the figure on the right, if
LED1, LED2, LED3, and LED4 are shorted, 4 times the
current set by the ISET pin can be passed.
VOUT
When using only 2 channels in a bundle, mount the
pulled-down resistor for each LED pin for unused
channels (2 channels).
When connected to multiple LED pins with a resistor,
the voltage value may be out of the set range and may
not be recognized as an unused channel. In this case,
the unintentional protection function may be activated,
so perform the LED pin handling correctly.
LED4
LED3
LED2
LED1
Figure 14. Application Example When LED Pins are Shorted
VOUT
VOUT
10 kΩ
10 kΩ
LED4
LED4
10 kΩ
LED3
LED2
LED1
LED3
LED2
LED1
Figure 15. Correct LED Pin Handling When Multiple
Channels are Unused
Figure 16. Wrong LED Pin Handling When Multiple
Channels are Unused
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
19/47
BD83A14EFV-M BD83A14MUF-M
Function Descriptions – continued
Unless otherwise stated, the value in the sentence is the Typ value.
2 DC/DC Converter
Detects the lowest voltage among LED1 to LED4 pin voltages (LED cathode voltages) in Minimum Channel Selector block
and inputs it to Error AMP. The reference voltage of Error AMP is generated in REF Voltage block based on RISET resistance
value, which becomes LED pin control voltage. The output of Error AMP is compared with the output of SLOPE block by
PWM COMP block, and a switching signal is output to the OUTL pin through DC/DC Control LOGIC.
2.1 LED Control Voltage VLEDCTL
2.5 DC/DC Converter Oscillation Frequency fOSC
2.6 Pulse Addition Function
2.7 External Synchronization / Spread Spectrum
Function (SSCG)
2.2 VCC Input Voltage and Number of LED Series
2.3 LED Variation and Series Number
2.4 Overvoltage Protection Function OVP
2.8 LSDET Function
2.1 LED Control Voltage VLEDCTL
DC/DC converter operates so that the lowest voltage among LED1 to LED4 pin voltages (LED cathode voltages) is equal
to the LED control voltage (VLEDCTL). Power dissipation can be minimized by optimizing the LED control voltage (VLEDCTL
)
according to the LED current (ILED).
1.2
LED Control Voltage Reference Value (VADIM_P = VREG
LED Control
)
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
ISET Resistor
RISET [kΩ]
LED Current
ILED [mA]
Voltage
VLEDCTL [V]
53.0
20.5
15.1
8.8
22.8
59.0
0.53
0.69
0.78
1.03
80.1
137.5
20 30 40 50 60 70 80 90 100 110 120 130 140 150
ILED [mA]
Figure 17. VLEDCTL vs ILED
2.2 VCC Input Voltage and Number of LED Series
To drive the boost DC/DC converter, the LED must be selected so that the output voltage (VOUT) is higher than the input
voltage (VCC).
ꢄ퐶퐶(
ꢄ퐶퐶(
< ꢄ푂푈ꢋ
< ꢄ푓
)
푀퐴푋
(푀ꢅ푁)
ꢄ퐶퐶
: Input voltage
ꢄ푂푈ꢋ : DC/DC converter output voltage
ꢌ
× ꢌ + ꢄ
)
푀퐴푋
(푀ꢅ푁)
퐿퐸퐷ꢍꢇ퐿(푀ꢅ푁)
: Number of LED series
: LED Vf voltage
: LED control voltage
Select the number of LED series and Vf characteristics that satisfy
the above equation.
ꢄ푓
ꢄ
퐿퐸퐷ꢍꢇ퐿
2.3 LED Variation and Series Number
When operating multiple LED outputs, the LED anode voltages in each row are commonly connected to DC/DC converter
output VOUT. LED pin voltage (LED cathode voltage) in the row where the Vf voltage of the LED is the highest is the lowest,
and this is controlled to be VLEDCTL. Therefore, the voltage of other LED pin outputs will be higher by the amount of Vf
variation. Select the number of LED series and Vf characteristics so that the LED short protection (VLEDn ≥ 5.0 V) does not
operate.
ꢌ × ꢎꢄ푓
) − ꢄ푓
)ꢏ < ꢄ
) − ꢄ
(
(
(
푀퐴푋
푀ꢅ푁
ꢆ퐻ꢐ푅ꢇ 푀ꢅ푁 퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
ꢄ
ꢆ퐻ꢐ푅ꢇ
: LED short protection voltage
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
20/47
BD83A14EFV-M BD83A14MUF-M
2 DC/DC Converter – continued
VOUT
2.4 Overvoltage Protection Function OVP
Inputs the resistor division of the output voltage VOUT
in the OVP pin. When OVP pin voltage rises the
overvoltage protection detect voltage VOVP (1.21 V) or
more, the overvoltage protection is activated, and the
switching of DC/DC converter is turned OFF. After that
when OVP pin voltage drops to 1.16 V, OVP is released.
ROVP2
OVP
+
ꢀ
ROVP1
1.21 V /
1.16 V
Figure 18. OVP Pin Voltage Setting Sample
{(
)
}
ꢄ푂푈ꢋꢐ푉푃 = ꢈꢐ푉푃1 + ꢈꢐ푉푃2 ∕ ꢈꢐ푉푃1 × ꢄꢐ푉푃
[V]
ꢄ푂푈ꢋꢐ푉푃
ꢄꢐ푉푃
: DC/DC converter output voltage (VOUT) during overvoltage protection operation
: Overvoltage protection detect voltage
2.5 DC/DC Converter Oscillator Frequency fOSC
The oscillation frequency (fOSC) of DC/DC converter can be set by connecting RRT between the RT pin and GND. The
oscillator frequency of DC/DC converter is generated in the OSC block. Set the resistor of RRT referring to the data and
theoretical formula below.
7
푓
: Oscillation frequency of DC/DC converter
: Constants determined inside the circuit
: RT pin connecting resistor
ꢐꢆꢍ
(
)
푓
ꢐꢆꢍ
= ꢂꢃ ∕ ꢈ푅ꢇ × 훼 [kHz]
ꢂꢃ7
ꢈ푅ꢇ
훼
: Correction factor
α is the correction factor. For the relation between fOSC and RRT including the correction factor, refer to fOSC vs RRT below.
Note that operation cannot be guaranteed if fOSC setting value exceeds the recommended range of 200 kHz to 2420 kHz.
Determine fOSC setting value in consideration of the variation in electrical characteristics, variation in RRT, and ON/OFF of
spread spectrum
2400
2200
Example of Resistance Value for fOSC Setting
2000
1800
1600
1400
1200
1000
800
RRT [kΩ]
45.0
33.3
20.8
20.0
10.0
4.0
α
1.006
1.000
0.987
0.986
0.957
0.882
600
400
200
4
14
24
34
44
RRT [kΩ]
Figure 19. fOSC vs RRT
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
21/47
BD83A14EFV-M BD83A14MUF-M
2 DC/DC Converter – continued
2.6 Pulse Addition Function
A pulse addition function is provided to output a stable DC/DC converter output voltage and LED current even when PWM
Duty is low. The output voltage can be held by outputting additional switching of several pulses after the falling edge of the
PWM input signal, and the LED can be turned on normally. When the pulse addition function is not used, set the PLSET
pin to OPEN
VPWM
0.5 V
VPLSET
Additional
Pulse Time
tPLSET
VOUTL
VOUT
VOUT Hold
Stable LED Current
ILED
Figure 20. Pulse Addition Function
The number of additional switching pulses is set in the capacitance value CPLSET connected to the PLSET pin. The additional
pulse time tPLSET is calculated as follows:
푡푃퐿ꢆ퐸ꢇ = ꢂꢃ10 × 퐶푃퐿ꢆ퐸ꢇ [µs]
푡푃퐿ꢆ퐸ꢇ
퐶푃퐿ꢆ퐸ꢇ
: Additional pulse time
: PLSET pin capacitance
1000
100
10
1
0
0.1
1.0
10.0
PLSET Pin Capacitance : CPLSET [nF]
Figure 21. tPLSET vs CPLSET
The additional pulse time required to hold the output voltage VOUT varies depending on various factors such as PWM
frequency, output voltage, output capacitance, LED current, as well as the minimum value of PWM Duty used for dimming.
Contact your sales representative when you request design verification of the required additional pulse time for your usage
conditions.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
22/47
BD83A14EFV-M BD83A14MUF-M
2 DC/DC Converter – continued
2.7 External Synchronization / Spread Spectrum Function (SSCG)
Three switching modes can be selected
according to the voltage input to the
SYNC pin.
Mode
1
VSYNC
Low
DC/DC Switching Frequency
Fixed Frequency Mode Determined by RRT
Spread Spectrum Mode of the Frequency
Determined by RRT
2
3
High (= VREG
Pulse Input
)
Mode to Synchronize with the Frequency Input to
the SYNC Pin
Mode 1:
When the SYNC pin is fixed Low, DC/DC converter switches at a fixed frequency determined by RRT
.
Mode 2:
By shorting the SYNC pin and the REG pin, operation in spread spectrum mode (SSCG) is enabled. With SSCG, noise
peaks can be reduced by periodically changing the oscillation frequency. The fluctuation range (Δf) of the frequency due to
SSCG is -8 % of the set oscillation frequency from the set oscillation frequency. The oscillation frequency fluctuation period
is 2.3 kHz.
Δf = fOSC x 0.08
VCC
VEN
VSYNC
Noise
reduction
VPWM
1.21 V
Pre-boost
Self Diagnosis
VOVP
VOUTL
Δf = -8 %
fOSC
fSSCG = 2.3 kHz
fOSC x 0.92
fOSC Frequency
Band
Figure 22. Spread Spectrum Function Timing Chart
Figure 23. Spread Spectrum Function
훥푓
푓
ꢐꢆꢍ
: Fluctuation range of the oscillation frequency by SSCG
: DC/DC oscillation frequency
훥푓 = 푓 × ꢃ.ꢃ8
ꢐꢆꢍ
푓
ꢆꢆꢍ퐺
: The oscillation frequency fluctuation period by SSCG
푓
ꢆꢆꢍ퐺
= ꢑ.3 [kHz]
When not using SSCG function, short the SYNC pin and the GND pin.
SSCG function cannot be turned ON/OFF during operation.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
23/47
BD83A14EFV-M BD83A14MUF-M
2.7 External Synchronization / Spread Spectrum Function (SSCG) – continued
Mode 3:
By inputting an external clock signal to the SYNC pin, the internal oscillation frequency can be externally synchronized.
However, note the following points.
·Since Mode is judged during Self Diagnosis (Initial Check), input the clock signal to the SYNC pin prior to turning the EN
pin to High.
·After the clock signal is input to the SYNC pin and the EN pin is turned High, it is not possible to switch between internal
oscillation and external synchronization. Operation may become unstable. After setting to Mode 3, it is possible to change
the external synchronization frequency during operation. However, evaluate the LED flickering due to fluctuations of the
output voltage.
·When using external synchronization, SSCG cannot be used.
·For the external synchronization frequency, input a frequency within ±10 % of the theoretical value of the DC/DC oscillation
frequency fOSC set by the RT pin.
Internal SYNC
4.0 V
1.0 V
VEN
VREG
VSYNC
REG
MODE
Selector
SYNC
SSCG: ON, SYNC: OFF
4.0 V
1.0 V
Internal
VSYNC
SSCG: OFF, SYNC: ON
SSCG: OFF, SYNC: OFF
7.12 ms
SSCG block
To OSC
Initial Check
Figure 24. Synchronous Signal (VSYNC) Input and
Mode Check (Initial Check) Timing
Figure 25. SYNC Pin Equivalence Circuit
LSDET
OFF
LSDET
ON
LSDET
OFF
2.8 LSDET Function
When the lowest LED pin voltage among LED pins is 2.4 V
or more, DC/DC converter is turned OFF, and COMP pin
voltage is held. DC/DC converter resumes switching when
the lowest LED pin voltage is less than VLEDCTL x 1.2.
LSDET function is intended to reduce the voltage quickly
when the output is over boosted. It also prevents the LEDs
from flickering by resuming the switching of DC/DC converter
just before returning to normal operation.
VPWM
ꢇ
VOUTL
ꢄ
VCOMP
①
The LED4 pin becomes open and LED4 pin voltage
becomes 0.3 V or less (Ⓐ).
ꢁ
1.21 V
DC/DC converter output begins boosting further to raise
LED4 pin voltage. In conjunction with this, OVP pin
voltage also rises (Ⓑ).
ꢅ
ꢂ
VOVP
②
When OVP pin voltage reaches 1.21 V (Ⓒ) due to the
boost of DC/DC converter, the LED open protection is
activated.
VLED1 to
VLED3
When the LED open protection is activated, the LED4
pin that was open is pulled up to REG pin voltage VREG
inside the IC (Ⓓ).
ꢆ
VLEDCTL
VLEDCTL x 1.2
LSDET function operates because LED4 pin voltage,
which is the lowest LED pin voltage in the LED pins, is
2.4 V or more (Ⓓ).
LSDET function turns OFF DC/DC converters and holds
COMP pin voltage (Ⓔ).
REG Pull Up (VREG
)
ꢃ
VLED4
VLEDCTL
2.4 V
0.3 V
ꢀ
③
④
DC/DC converter turns OFF, the output voltage drops,
and OVP pin voltage also drops (Ⓕ).
LED4
Open
LED4
Open
Detection
When the lowest LED pin voltage is less than VLEDCTL
x
ILED1
to
1.2 (Ⓖ), DC/DC converter resumes switching (Ⓗ).
ILED3
ILED4
Figure 26. LSDET Function When LEDs are Open
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
24/47
BD83A14EFV-M BD83A14MUF-M
Function Descriptions – continued
Unless otherwise stated, the value in the sentence is the Typ value.
3 Starting Sequence and Effective Section of Each Protection Function
The timing chart at startup and the effective section of each protection function are shown in the figure below.
①
Power ON
: Input EN pin voltage after the VCC pin voltage is input.
Input the ADIM_P pin voltage at the same time as the EN pin voltage at the latest after inputting
the VCC pin voltage.
②
Self Diagnosis
(Initial check)
: After inputting EN pin voltage, this IC becomes the Self Diagnosis status, determines the channel
to be used, and sets the external synchronization / spread spectrum function, etc. Self Diagnosis is
completed after 7.12 ms, and the diagnostic status is latched.
③
④
Pre-boost
: After Self Diagnosis, pre-boost starts at VPWM = High, and after 7.12 ms, pre-boost is completed.
Stable operation : The LED current flows according to On Duty of the PWM signal input to the PWM pin. The output
transition section voltage of DC/DC converter with switching turned OFF drops according to the
load current.
⑤
Stable state
: When LED pin voltage (the lowest voltage in LED1 to LED4) drops to LED control voltage x 1.2,
DC/DC converter switches again.
VCC
VADIM_P
5.5V
VEN
4.1 V
(UVLO Release)
VREG
VPWM
ꢌ
ꢈ Self Diagnosis
After Self Diagnosis,
pre-boost starts with VPWM = High
7.12 ms
・Determination of CH to use
・Setting external
synchronization
ꢋ Stable Operation
ꢉ Pre-boost
ꢊ Stable State
7.12 ms
Transition Section
・Setting spread spectrum
・OVP pin fault detection
・ISET pin fault detection
1.21 V
VOVP
VOUTL
ILED
LED Setting Current Output Section
LED Control Voltage × 1.2
VLED
LED Control Voltage
During Self Diagnosis
FAIL is Low
VFAIL
DC/DC Converter Operating Section
Current Driver Operating Section
Under Voltage Lockout (UVLO) Effective when EN = High
Thermal Shutdown REG (TSDREG) Effective when EN = High
Thermal Shutdown LED (TSDLED) Effective when EN = High
Overcurrent Protection (OCPL) Effective when UVLO is released
Overvoltage Protection (OVP) Effective when UVLO is released
Overvoltage Protection (OVP) / FAIL Flag Effective when LSDET is OFF
Input Overcurrent Protection (OCPH) / FAIL Flag Effective when UVLO is released
ISET-GND Short Protection / FAIL Flag Effective when Self Diagnosis is completed
LED Open Protection / FAIL Flag Effective when pre-boost is completed
LED Short Protection / FAIL Flag Effective when pre-boost is completed
Short Circuit Protection (SCP) / FAIL Flag Effective when pre-boost is completed
Figure 27. Timing Chart at Startup and Effective Section of Each Protection Function
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
25/47
BD83A14EFV-M BD83A14MUF-M
3 Starting Sequence and Effective Section of Each Protection Function – continued
Unless otherwise stated, the value in the sentence is the Typ value.
3.1 Self Diagnosis (Initial Check)
The contents of Self Diagnosis are as follows.
3.1.1 LED Pin Used / Unused Check
It is possible to check whether the LED pin is used or not by LED pin voltage at the end of Self Diagnosis. If LED pin
voltage is 0.3 V or more and 2.5 V or less during Self Diagnosis, the LED pin is diagnosed as unused. If it is diagnosed
as unused, the LED pin does not operate and is pulled up to REG pin voltage VREG inside the IC. To select unused
channels correctly, the capacitance value to be connected to the LED pin should be 470 pF or less.
3.1.2 SYNC Pin Setting Check
ON/OFF of the external synchronization or spread spectrum function can be set by SYNC pin voltage at the end of Self
Diagnosis.
3.1.3 FAIL Pin Connection Check
During Self Diagnosis, the FAIL pin can check the connection between the monitor pin of MCU and the FAIL pin by
turning ON the open drain output (ON resistor = 1 kΩ). Determine the pull up voltage and pull up resistor according to
FAIL detection voltage on the MCU.
3.1.4 ISET-GND Short Check
In Self Diagnosis, ISET-GND Short Check is done under the same conditions as ISET pin fault (ISET-GND short
protection). When ISET-GND short is confirmed, the load switch, DC/DC switching, and current driver are latched OFF.
It is reset when VEN = Low or UVLO is detected.
3.1.5 OVP Pin Setting Check
Self Diagnosis checks OVP pin setting. The OVP pin during Self Diagnosis is pulled down with IC built-in resistor of 1
MΩ. When an open failure of the OVP pin occurs, OVP pin voltage falls to 0.1 V or less, and the load switch, DC/DC
switching, and the current driver latch OFF. It is reset when VEN = Low or UVLO is detected.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
26/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Function Descriptions – continued
4 Stopping Sequence and Effective Section of Each Protection Function
The figure below shows the timing chart when stopping and the effective section of each protection function.
⑤
Stable state
: When LED pin voltage (the lowest voltage in LED1 to LED4) drops to the LED control voltage x 1.2,
DC/DC converter is switched again.
⑥
Standby state : Decrease EN pin voltage and ADIM_P pin voltage prior to the VCC pin voltage falling.
Internal circuit is stopped by falling EN pin voltage, and IC is in standby state.
VCC
VADIM_P
VEN
REG output
function is OFF
when EN = Low
VREG
VPWM
ꢍ Standby State
ꢊ Stable State
VOVP
VOUTL
ILED
DCDC converter operation is OFF
when EN = Low
Current driver operation is OFF
when EN = Low
VLED
LED Control Voltage
VFAIL
DC/DC Converter Operating Section
Current Driver Operating Section
Under Voltage Lockout (UVLO) Effective when EN = High
Thermal Shutdown REG (TSDREG) Effective when EN = High
Thermal Shutdown LED (TSDLED) Effective when EN = High
Overcurrent Protection (OCPL) Effective when UVLO is released
Overvoltage Protection (OVP) Effective when UVLO is released
Overvoltage Protection (OVP) / FAIL Flag Effective when LSDET is OFF
Input Overcurrent Protection (OCPH) / FAIL Flag Effective when UVLO is released
ISET-GND Short Protection / FAIL Flag Effective when Self Diagnosis is completed
LED Open Protection / FAIL Flag Effective when pre-boost is completed
LED Short Protection / FAIL Flag Effective when pre-boost is completed
Short Circuit Protection (SCP) / FAIL Flag Effective when pre-boost is completed
By setting EN = Low,
the state is set to standby
and all functions are stopped.
Figure 28. Timing Chart at Stopping and Effective Section of Each Protection Function
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
27/47
BD83A14EFV-M BD83A14MUF-M
PCB Application Circuit Diagram
ꢌ
L1
B+
B-
CM
CB2
CB1
CCSH
RCSH3
CVCC2 CVCC1
CVCC3
RCSH2 RCSH1
ꢉ
M1
REG
L2
D1
VOUT
REG
VCC
CSH
REG
CREG
EN
GND
EN
CLDSW
M2
CIN1 CIN2
RG
COUT1 COUT2 COUT3 COUT4
LDSW
N.C.
RSYNCU
PWM
PWM
SYNC
ADIM_P
COMP
RT
SYNC
OUTL
CSL
RCSL
RSYNCD
PGND
PLSET
FAIL
CCOMP2
RCOMP1
RFAIL
CPLSET1
REG
CPLSET2
ROVP2
REG
FAIL
ISET
LGND
LED1
LED2
CCOMP1
OVP
RISET1
RADIM_P
LED4
LED3
COVP
ROVP1
ADIM_P
RISET2
VOUT
LED4
LED3
LED2
LED1
RRT1
CLED1U CLED2U CLED3U CLED4U
RRT2
CLED1D CLED2D CLED3D CLED4D
RLED1 RLED2 RLED3 RLED4
①
Place the Input overcurrent detect resistors RCSH1, RCSH2, VCC pin capacitors CVCC1, CVCC2, and the load switch M1 so that
they are shortest. Also, place the input filters RCSH3, CCSH for detecting the input overcurrent close to the CSH pin. They can
be placed on the opposite side of the IC and connected with a via.
②
③
Place the input capacitors CIN1, CIN2 so that they are as short as the components of both the inductor L2 and the load switch
M1. Connect the ground of CIN1, CIN2 to the PGND pin via EXP-PAD on the surface layer.
To reduce high frequency noises, the wires of the boost "Loop" must be as short as possible. Do not widen the wiring width
more than necessary.
·Place the boost FET M2 Drain, the inductor L2 and the anodes of the diode D1 so that they are the shortest.
·Place the cathode of D1 and the output decoupling capacitors COUT1, COUT2, COUT3, and COUT4 and RCSL so that they are
the shortest.
·Place the output decoupling capacitors COUT1, COUT2, COUT3, COUT4 and the PGND pin so that they are the
shortest.
·Place the PGND pin, RCSL and the boost FET M2 Source so that they are the shortest.
·Place the IC and each component on the same surface layer of the board and make connections in the same layer.
④
⑤
Place the ground plane on the layer closest to the surface layer where the IC is placed.
Connect the EXP-PAD to the board ground. Wire the ground pattern connected from the EXP-PAD as wide as possible to
improve heat dissipation and connect it to the ground plane with many vias. To ensure heat dissipation according to power
loss, place the required number of thermal vias directly under the EXP-PAD and connect them to the ground plane.
There is no problem if the GND pin, the LGND pin and the PGND pin are connected via the EXP-PAD. However, the power
system ground such as the ground of the output decoupling capacitor and the PGND pin contains the noise component of
the switching frequency. To reduce this noise component, it is recommended to connect to the ground plane using many
vias in the ground pattern around the power system ground.
⑥
⑦
⑧
Place the bypass capacitor (CREG) between the REG pin and the GND pin as close to pin as possible.
The connection from VOUT to the anode of the LED panel and the connection from the cathode of the LED panel to the
LED1, LED2, LED3, LED4 pins should be as short as possible. Depending on the parasitic inductance component, the LED
current may become unstable.
⑨
Do not run the wiring from the cathode of the LED panel to the LED1, LED2, LED3, LED4 pins in parallel with other active
lines. Also, place the noise reduction capacitors (CLED1D, CLED2D, CLED3D, CLED4D) so that they are as short as the LED pin.
RLED1, RLED2, RLED3, RLED4 are pull-down resistors connected to the LED pin of unused channel and is required to generate
LED pin voltage that is judged to be unused.
⑩
⑪
⑫
When using the PWM function, the PWM pin is the active line, so keep it away from other sense lines.
When using the external synchronization function, the SYNC pin is an active line, so keep it away from other sense lines.
When using the DC dimming function, the ADIM_P pin is an active line, so keep it away from other sense lines.
⑬ Place R and C connected to the ADIM_P pin, the COMP pin, the RT pin, the ISET pin, the PLSET pin, and the OVP pin as
close to the IC as possible. They can be placed on the opposite side of the IC and connected with a via.
⑭
⑮
Since OVP pin voltage must be 0.1 V or more during Self Diagnosis, when installing the COVP, use about 1000 pF as a guide.
When the VCC voltage is turned ON setting the EN pin to Low, the voltage between the VCC-LDSW pins may open
momentarily and an inrush current may flow depending on the VCC startup speed and the type of load switch(M1) used. Be
sure to check with the actual application.
⑯
The MUF package requires external components to prevent adjacent short between the OUTL pin and LDSW pin. If
concerned, consider the EFV package.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
28/47
BD83A14EFV-M BD83A14MUF-M
List of External Components
Serial No.
1
Component Name
CB1
Component Value
Product Name
Manufacturer
-
-
-
2
CM
Short
-
-
3
CB2
-
-
-
4
L1
Short
-
-
5
CVCC1
CVCC2
CVCC3
RCSH1
RCSH2
RCSH3
CCSH
1 μF
GCM21BR71H105KA03
murata
6
-
-
-
7
1 μF
GCM21BR71H105KA03
murata
8
15 mΩ
LTR18 Series
Rohm
9
-
-
-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
100 Ω
MCR03 Series
Rohm
100 pF
GCM1882C2A101JA01
murata
CLDSW
M1
-
-
-
60 V / 36 A
SQJ457EP
VISHAY
CIN1
10 μF
GCM32EC71H106KA03L
murata
CIN2
10 μF
GCM32EC71H106KA03L
murata
L2
22 μH
CLF10060NIT-220M-D
TDK
D1
60 V / 5 A
RB088LAM-60TF
Rohm
M2
60 V / 8 A
RD3L080SN
Rohm
RCSL
75 mΩ
LTR18 Series
Rohm
RG
Short
-
-
COUT1
COUT2
COUT3
COUT4
ROVP1
ROVP2
COVP
10 μF
GCM32EC71H106KA03L
murata
10 μF
GCM32EC71H106KA03L
murata
-
-
-
33 μF
GYA1H330MCQ1GS
nichicon
10 kΩ
MCR03 Series
Rohm
330 kΩ
MCR03 Series
Rohm
1000 pF
GCM1887U1H102JA01
murata
RFAIL
100 kΩ
MCR03 Series
Rohm
CPLSET1
CPLSET2
RLED1
RLED2
RLED3
RLED4
CLED1U
CLED2U
CLED3U
CLED4U
CLED1D
CLED2D
CLED3D
CLED4D
1000 pF
GCM1887U1H102JA01
murata
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
29/47
BD83A14EFV-M BD83A14MUF-M
List of External Components – continued
Serial No.
Component Name
CREG
Component Value
2.2 μF
-
Product Name
Manufacturer
43
44
45
46
47
48
49
50
51
52
53
GCM21BR71C225KA49
murata
-
RSYNCU
RSYNCD
RRT1
-
100 kΩ
33 kΩ
Short
MCR03 Series
Rohm
Rohm
-
MCR03 Series
RRT2
-
RCOMP1
CCOMP1
CCOMP2
RISET1
200 Ω
0.1 μF
-
MCR03 Series
Rohm
murata
-
GCM155R11C104KA40D
-
15 kΩ
Short
MCR03 Series
-
Rohm
-
RISET2
RADIM_P
100 kΩ
MCR03 Series
Rohm
Note: The component constants vary depending on the operating conditions and the load used.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
© 2022 ROHM Co., Ltd. All rights reserved.
30/47
TSZ22111 • 15 • 001
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected
Unless otherwise stated, the values in sentences are the values in continuous mode.
Select the application components according to the following procedure.
1. Derivating Maximum Input (Inductor) Peak Current IL(MAX)
2. Selecting Inductor Constant
Feedbacks the L value
NG
3. Setting Overcurrent Detect Resistor (RCSL
)
4. Setting Input Overcurrent Detect Resistor (RCSH
)
5. Selecting PLSET Capacitance
6. Selecting Output Capacitance
7. Selecting Input Capacitance
8. Setting Overvoltage Protection (OVP)
9. Checking Rated Voltage/Current of Inductor (L), Diode (D1), MOSFET (M1,
M2), Resistor (RCSH, RCSL), and Capacitance (CIN, COUT
)
10. Setting Phase Compensation Circuit
11. Operation Check on Actual Device
Figure 29. Application Components Selection Procedure
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
31/47
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected – continued
1 Derivating Maximum Input (Inductor) Peak Current IL(MAX)
VCC
CVCC
RCSH
CSH
LDSW
M1
CIN
L1
D1
VOUT
COUT
M2
OUTL
CSL
RCSL
PGND
Figure 30. Output Application Circuit Diagram
1.1 Calculating Maximum Output Voltage VOUT(MAX)
Calculates VOUT(MAX) in consideration of LED Vf variation and the number of LED stages.
ꢄ푂푈ꢋ
= ꢄ푓
× ꢌ + ꢄ
(푀퐴푋)
(푀퐴푋) 퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
ꢄ푂푈ꢋ
ꢄ푓
: Maximum output voltage
: Maximum value of LED Vf voltage
(푀퐴푋)
(푀퐴푋)
ꢌ
ꢄ
: Number of LED series
: Maximum value of LED control voltage
퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
1.2 Calculating Maximum Output Current IOUT(MAX)
: Maximum output current
퐼ꢐꢒꢇ(푀퐴푋)
퐼퐿퐸퐷(푀퐴푋)
퐼ꢐꢒꢇ(푀퐴푋) = 퐼퐿퐸퐷(푀퐴푋) × ꢓ
: Maximum value of LED current per
channel
ꢓ
: Number of LED parallels
1.3 Calculating Maximum Input (Inductor) Peak Current IL(MAX)
ꢂ
퐼퐿(푀퐴푋) = 퐼퐿퐴푉퐺(푀퐴푋) + ∆퐼퐿(푀퐴푋)
퐼퐿(푀퐴푋)
: Maximum input (inductor) peak
current
ꢑ
: Maximum input (inductor) average
current
: Maximum input (inductor) current
amplitude
: Minimum power supply voltage
: Efficiency (about. 85 %)
퐼퐿퐴푉퐺(푀퐴푋)
IOUT(MAX)
∆퐼퐿(푀퐴푋)
퐼퐿퐴푉퐺(푀퐴푋) = ꢄ푂푈ꢋ
×
(푀퐴푋)
휂 × ꢄ퐶퐶(푀ꢅ푁)
ꢄ퐶퐶(푀ꢅ푁)
휂
ꢝ(푀ꢅ푁)
푉ꢍꢍ
VOUT
ꢜ푉ꢍꢍ
(ꢔꢀꢕ)
1
(ꢔꢀꢕ)
(ꢙꢚꢛ)
∆퐼퐿(푀퐴푋)
=
×
×
: Minimum value of inductance
퐿
ꢖ
VOUT
(ꢙꢚꢛ)
(ꢔꢀꢕ)
ꢗ푆ꢘ(ꢔꢀꢕ)
: Minimum value of DC/DC
oscillation frequency
푓
ꢐꢆꢍ(푀ꢅ푁)
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
32/47
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected – continued
2 Selecting Inductor Constant
To maintain stable continuous operation of the current mode DC/DC converter, the L (inductance) value must satisfy the
following requirements:
푉ꢐꢒꢇꢜ푉ꢍꢍ
4020
ꢄ푂푈ꢋ
ꢄ퐶퐶
ꢝ
: Output voltage
: Power supply voltage
: Inductance value
ꢈꢍꢆ퐿
×
≤
ꢞ
퐿×10
푅
ꢟ푇
ꢈ푅ꢇ
ꢈꢍꢆ퐿
: RT pin connecting resistor
: CSL pin connecting resistor
Rewriting about L is as follows
(VOUTꢜ푉ꢍꢍ)×푅 ×푅
ꢟ푇
ꢘ푆ꢠ
ꢝ ≥
ꢞ
4020×10
Consider the variation of the L value and set it with sufficient margin.
3 Setting Overcurrent Detect Resistor (RCSL
)
ꢄꢐꢍ푃퐿(푀ꢅ푁)
퐼ꢐꢍ푃퐿(푀ꢅ푁) : Minimum value of overcurrent protection
퐼ꢐꢍ푃퐿(푀ꢅ푁)
=
detect current
ꢈꢍꢆ퐿(푀퐴푋)
: Minimum value of overcurrent protection
detect voltage
: Maximum value of overcurrent detect
resistor
ꢄꢐꢍ푃퐿(푀ꢅ푁)
ꢈꢍꢆ퐿(푀퐴푋)
푡ꢐꢍ푃퐿
ꢄ퐶퐶(푀퐴푋)
ꢝ(푀ꢅ푁)
> 퐼퐿(푀퐴푋)
+
× 푡ꢐꢍ푃퐿
: OCPL detect delay time (Max = 84 ns)
Select the RCSL value so that it will be as above.
4 Setting Input Overcurrent Detect Resistor (RCSH
)
ꢄꢐꢍ푃퐻(푀ꢅ푁)
: Minimum value of input overcurrent
protection detect current
: Minimum value of input overcurrent
protection detect voltage
퐼ꢐꢍ푃퐻(푀ꢅ푁)
퐼ꢐꢍ푃퐻(푀ꢅ푁)
=
ꢈꢍꢆ퐻(푀퐴푋)
ꢄꢐꢍ푃퐿(푀퐴푋) ꢄ퐶퐶(푀퐴푋)
ꢄꢐꢍ푃퐻(푀ꢅ푁)
>
+
× tOCPL
ꢈꢍꢆ퐻(푀퐴푋) : Maximum value of input current detect
ꢈꢍꢆ퐿(푀ꢅ푁)
ꢝ(푀ꢅ푁)
resistor
: Maximum value of overcurrent protection
detect voltage
ꢄꢐꢍ푃퐿(푀퐴푋)
Select the RCSH value so that it will be as above.
ꢈꢍꢆ퐿(푀ꢅ푁) : Minimum value of overcurrent detect
resistor
푡ꢐꢍ푃퐿
: OCPL detect delay time (MAX = 84 ns)
5 Selecting PLSET Capacitance
푉ꢐꢒꢇ
퐼ꢐ퐹퐹퐿ꢐ퐴퐷 푀퐴푋
=
(ꢔꢡꢢ) + 퐼ꢆ퐵퐷 푀퐴푋
( )
ꢗꢣꢤ(ꢔꢀꢕ)
퐼ꢐ퐹퐹퐿ꢐ퐴퐷(푀퐴푋) : Maximum value of load current when
(
)
푅
PWM = OFF
ꢈꢐ푉푃(푀ꢅ푁)
퐼ꢆ퐵퐷(푀퐴푋)
: Minimum value of overvoltage protection
detect resistor
: Maximum value of rectifier diode leakage
current
푄ꢐ퐹퐹퐿ꢐꢆꢆ 푀퐴푋 = 퐼
) × 푡푃푊푀ꢐ퐹퐹 푀퐴푋
(
(
)
(
)
ꢐ퐹퐹퐿ꢐ퐴퐷 푀퐴푋
2.5
푄푃푊푀푅ꢅꢆ퐸
=
× 퐼ꢐꢒꢇ(푀ꢅ푁)
ꢗ푆ꢘ(ꢔꢀꢕ)
푄ꢐ퐹퐹퐿ꢐꢆꢆ(푀퐴푋) : Maximum value of consumed charge
when PWM = OFF
ꢖ
푡푃푊푀ꢐ퐹퐹(푀퐴푋) : Maximum value of PWM = OFF time
푉
×ꢍ
ꢤꢠ푆ꢁ푇(ꢔꢀꢕ)
푄푃퐿ꢆ퐸ꢇ 푀ꢅ푁
=
ꢤꢠ푆ꢁ푇(ꢔꢀꢕ) × 퐼ꢐꢒꢇ(푀ꢅ푁)
(
)
푄푃푊푀푅ꢅꢆ퐸
푄푃퐿ꢆ퐸ꢇ(푀ꢅ푁)
: Insufficient charge after PWM rise
: Minimum value of additional pulse output
supply charge
ꢅ
ꢤꢠ푆ꢁ푇(ꢔꢡꢢ)
푄푃퐿ꢆ퐸ꢇ 푀ꢅ푁 > 푄
) + 푄푃푊푀푅ꢅꢆ퐸
ꢄ푃퐿ꢆ퐸ꢇ(푀ꢅ푁)
: Minimum value of PLSET threshold
voltage
(
)
(
ꢐ퐹퐹퐿ꢐꢆꢆ 푀퐴푋
퐶푃퐿ꢆ퐸ꢇ(푀ꢅ푁)
퐼푃퐿ꢆ퐸ꢇ(푀퐴푋)
: Minimum value of PLSET pin capacitance
: Maximum value of PLSET charging
current
Select the CPLSET value so that it will be as above.
퐼ꢐꢒꢇ(푀ꢅ푁)
: Minimum output current
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
33/47
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected – continued
6 Selecting Output Capacitance
The capacitor COUT used for the output is determined by the allowable amount of VOUTPP which is the ripple voltage of
VOUT.
푉
×ꢍ
×ꢅ
ꢅ
퐷
)
(
)
ꢤꢠ푆ꢁ푇(ꢔꢡꢢ)
(
)
(
(
)
ꢤꢠ푆ꢁ푇 ꢔꢡꢢ
ꢗꢥ푇 ꢔꢡꢢ
ꢗꢥ푇 ꢔꢡꢢ × ꢗꢕ ꢔꢡꢢ
ꢄ푂푈ꢋ푃푃(푀퐴푋)
=
+
+ 퐼퐿(푀퐴푋) × ꢈ퐸ꢆ푅(푀퐴푋)
)
ꢅ
×ꢍ
ꢍ
×ꢖ
)
ꢗꢥ푇 ꢔꢀꢕ ꢗ푆ꢘ ꢔꢀꢕ
(
)
(
)
(
(
ꢤꢠ푆ꢁ푇 ꢔꢀꢕ
ꢗꢥ푇 ꢔꢀꢕ
: Maximum value of VOUT ripple voltage
: Maximum value of PLSET threshold
voltage
퐶푃퐿ꢆ퐸ꢇ(푀퐴푋) : Maximum value of PLSET pin capacitance
ꢄ푂푈ꢋ푃푃(푀퐴푋)
퐼푃퐿ꢆ퐸ꢇ(푀ꢅ푁)
ꢄ푃퐿ꢆ퐸ꢇ(푀퐴푋)
: Minimum value of PLSET charging
current
: Maximum output current
: Maximum value of DCDC Duty
퐼ꢐꢒꢇ(푀퐴푋)
퐶ꢐꢒꢇ(푀ꢅ푁)
ꢊꢐ푁(푀퐴푋)
: Minimum value of output capacitance
: Minimum value of DC/DC oscillation
frequency
푓
ꢐꢆꢍ(푀ꢅ푁)
퐼퐿(푀퐴푋)
: Maximum input (inductor) peak current
ꢈ퐸ꢆ푅(푀퐴푋)
: Maximum value of equivalence serial
resistor for output capacitance COUT
The actual VOUT ripple voltage is affected by board layout and component characteristics. Be sure to check on the actual
device and set the capacitance value considering sufficient margin so that it will be within the allowable ripple voltage.
The maximum value of COUT that can be set is 100 μF.
7 Selecting Input Capacitance
A ceramic capacitor with an input capacitance of 10 μF or more and a low ESR is recommended. If a capacitor outside
this range is selected, an excessive ripple voltage may be superimposed on the input voltage, causing IC malfunction.
In addition, the capacitor CIN used for the input is determined by the allowable amount of VINPP which is the ripple voltage
of VIN.
8 Setting Overvoltage Protection (OVP)
Overvoltage protection (OVP) is set by an external resistors ROVP1
,
VOUT
ROVP2. When the OVP pin becomes 1.21 V or more, it detects
overvoltage and stops DC/DC switching. Also, when the OVP pin is
1.21 V or more and the LED1 to LED4 pin voltage is 0.3 V or less,
the open state is detected, and the circuit is latched off (Reference
PROTECT).
ROVP2
OVP
To prevent an open false detection, the resistor division voltage of
the maximum value of the output voltage must be below the minimum
value of open detection voltage.
+
ꢀ
ROVP1
1.21 V /
1.16 V
Set ROVP1, ROVP2 so that they satisfy the following formulas.
Figure 31. OVP Application Circuit Diagram
ꢄ푂푈ꢋ
: Maximum output voltage
ꢈꢐ푉푃1
(푀퐴푋)
ꢄ푂푈ꢋ
×
< ꢄꢐ푉푃퐷퐸ꢇ(푀ꢅ푁)
(푀퐴푋)
ꢈꢐ푉푃1
: Overvoltage protection detect
resistor (GND side)
(
)
ꢈꢐ푉푃1 + ꢈꢐ푉푃2
ꢈꢐ푉푃2
: Overvoltage protection detect
resistor (VCC side)
(1)
ꢄꢐ푉푃퐷퐸ꢇ(푀ꢅ푁) : Minimum value of overvoltage
e.g.) When using 8 series of LEDs with RISET = 15.1 kΩ and Vf = 3.2
V ±0.2 V.
protection detect voltage
ꢈꢅꢆ퐸ꢇ
ꢄ푂푈ꢋ
ꢄ
: Resistor for LED current setting
: Maximum output voltage
(
)
ꢄ푂푈ꢋ
= 3.ꢑ + ꢃ.ꢑ × 8 + ꢄ
(
)
(
)
푀퐴푋
퐿퐸퐷ꢍꢇ퐿 푀퐴푋
(푀퐴푋)
: Maximum value of LED control
voltage
퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
= ꢑ8.ꢃꢦ [V]
ꢈꢐ푉푃1
: Overvoltage protection detect
resistor (GND side)
ꢄꢐ푉푃퐷퐸ꢇ(푀ꢅ푁) = ꢂ.ꢂꢧ3 [V]
ꢈꢐ푉푃2
: Overvoltage protection detect
resistor (VCC side)
ꢄꢐ푉푃퐷퐸ꢇ(푀ꢅ푁) : Minimum value of overvoltage
If ROVP1 = 20 kΩ, it is necessary to set ROVP2 > 459 kΩ from equation
(1).
protection detect voltage
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
34/47
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected – continued
9 Checking Rated Voltage/Current of Inductor (L), Diode (D1), MOSFET (M1, M2), Resistor (RCSH, RCSL,), and
Capacitance (CIN, COUT
)
(Note 1)
Rated Current
Rated Voltage
Power Dissipation
Input Overcurrent Detect Resistor RCSH
Overcurrent Detect Resistor RCSL
MOSFET M1
-
-
-
> IOCPH(MAX)2 x RCSH(MIN)
> IOCPL(MAX)2 x RCSL(MIN)
-
(Note 2)
> IOCPH(MAX)
> VCC(MAX)
> VCC(MAX)
> VCC(MAX)
-
-
-
-
-
-
-
(Note 3)
MOSFET M2
> IOCPL(MAX)
Input Capacitance CIN
Inductor L
-
(Note 4)
> IA(MAX)
(Note 4)
(Note 5)
Diode D1
> IA(MAX)
> VOUTOVP(MAX)
Output Capacitance COUT
-
> VOUTOVP(MAX)
(Note 1) Consider the variation of external components and make setting with sufficient margin.
(Note 2)퐼ꢐꢍ푃퐻(푀퐴푋) = ꢄꢐꢍ푃퐻(푀퐴푋)/ꢈꢍꢆ퐻(푀ꢅ푁)
(Note 3)퐼ꢐꢍ푃퐿(푀퐴푋) = ꢄꢐꢍ푃퐿(푀퐴푋)/ꢈꢍꢆ퐻(푀ꢅ푁)
푉ꢍꢍ(ꢔꢡꢢ)
× tOCPL
퐿(ꢔꢀꢕ)
(Note 4)퐼퐴(푀퐴푋) = 퐼ꢐꢍ푃퐿(푀퐴푋)
+
푡ꢐꢍ푃퐿 : OCPL detect delay time (MAX = 84 ns)
Since the inductor current reaches IOCPL at startup, the recommended setting is Rated Current > IA(MAX)
However, it is possible to set Rated Current > IL(MAX) after confirming that no damage occurs in the actual device.
(Note 5) DC reverse voltage
.
10 Setting Phase Compensation Circuit
About application stability conditions
The stability conditions of the LED voltage feedback system are as follows.
(1) Phase delay when gain is 1 (0 dB) is 150° or less (i.e., phase margin is 30° or more)
(2) Frequency (unity gain frequency) when gain is 1 (0 dB) is 1/10 or less of switching frequency
By inserting phase lead fz near the unity gain frequency,
VOUT
stability can be ensured by phase compensation.
The phase delay fp1 is determined by COUT and the
output impedance RL. Each is as follows.
Phase lead 푓푧 = ꢂ/(ꢑ휋 × ꢈ푃ꢍ × 퐶푃ꢍ) [Hz]
Phase delay 푓푝ꢂ = ꢂ/(ꢑ휋 × ꢈ퐿 × 퐶ꢐꢒꢇ
)
[Hz]
LED1 to
LED 4
Error
AMP
* Output impedance calculated by ꢈ퐿 = ꢄ푂푈ꢋ/퐼ꢐꢒꢇ
COMP
-
Good results can be obtained by setting fz from 1 kHz to
10 kHz. Substitute the value at maximum load for RL.
+
RCOMP
CCOMP
PWM
COMP
Figure 32. Error AMP Block Application Circuit Diagram
In addition, this setting is a simple calculation and is not calculated exactly, so it may be necessary to make adjustments
on the actual device. Also, these characteristics will change depending on the board layout, load conditions, etc., so
when designing for mass production, make sure to check the actual device before setting.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
35/47
BD83A14EFV-M BD83A14MUF-M
Selection of Components Externally Connected – continued
11 Operation Check on Actual Device
Select the constant according to the above procedure and precautions regarding constant setting. In addition, since this
selection is calculated by theoretical calculation, it does not include variations in external components or changes in their
characteristics and is not guaranteed. The parameters that affect the characteristics of the product will change depending
on the actual layout pattern, such as power supply voltage, LED current / number of lamps, inductor, output capacitance,
and switching frequency, so be sure to check with the actual device.
Additional Components for EMC Countermeasure
The figure below shows the examples of EMC countermeasure components.
(1) Capacitor for boost FET current loop noise reduction
(2) Capacitor for output current loop noise reduction
(3) Capacitor for power line high frequency noise reduction
(4) Low-pass filter for power line noise reduction
(5) Common mode filter for power line noise reduction
(6) Snubber circuit for boost FET high frequency noise reduction
(7) Snubber circuit for ringing reduction during boost FET switching
5
4
3
RCSH
M1
VCC
CVCC
1
CIN
L1
VREG
1
2
24
23
22
21
20
19
18
17
16
15
14
13
REG
GND
EN
VCC
7
CREG
CSH
LDSW
N.C.
6
EN
PWM
3
VOUT
4
PWM
SYNC
ADIM_P
COMP
RT
D1
M2
2
SYNC
5
OUTL
CSL
COUT
ADIM_P
6
ROVP2
RCSL
CCOMP RCOMP
EXP-PAD
7
PGND
PLSET
FAIL
RRT
8
ROVP1
RFAIL
CPLSET
RISET
VREG
VFAIL
9
ISET
LGND
LED1
LED2
10
11
12
OVP
LED4
LED3
Figure 33. Application Circuit Diagram Reference Example (including EMC countermeasure components)
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
36/47
BD83A14EFV-M BD83A14MUF-M
Precautions for PCB Layout
PCB layout patterns have a significant impact on efficiency and ripple
characteristics, so care must be taken when designing. In the boost
configuration, there is a "Loop" as shown in the figure on the right.
Place the components in the Loop as close as possible (e.g., place
GND of COUT and PGND as close together).
VCC
CVCC
RCSH
CSH
LDSW
M1
L1
Also, make sure that the wiring in each loop is as low impedance as
possible.
Refer to "PCB Application Circuit Diagram" for other detailed
precautions regarding PCB layout.
CIN
D1
VOUT
COUT
M2
OUTL
CSL
Loop
RCSL
PGND
Figure 34. Circuit of DC/DC Block
LOOP
Figure 35. BD83A14EFV-M PCB TOP-layer
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
37/47
BD83A14EFV-M BD83A14MUF-M
Power Consumption Calculation Example
The maximum value of IC power consumption can be easily calculated by the following procedure. Take heat dissipation
measures so that the rise in chip temperature due to this power consumption does not exceed Tjmax under the environmental
conditions (ambient temperature, heat dissipation fins, etc.) used by the customer.
ꢨꢍ(푀퐴푋) = 퐼ꢍꢍ(푀퐴푋) × ꢄ퐶퐶(푀퐴푋)
+퐶ꢅꢆꢆ(푀퐴푋) × ꢄ푅퐸퐺(푀퐴푋) × 푓
(1) Circuit power
× ꢄ푅퐸퐺(푀퐴푋)
(2) OUTL FET drive stage power
ꢐꢆꢍ(푀퐴푋)
( )
)) × ꢌ × ꢓ − ꢂ } × 퐼퐿퐸퐷 푀퐴푋
( )
푀ꢅ푁
+{ꢄ
) × ꢓ + (ꢄ푓
) − ꢄ푓
(
(
(
퐿퐸퐷ꢍꢇ퐿 푀퐴푋
푀퐴푋
(3) Current driver power
ꢄ푂푈ꢋ
= ꢄ푓
× ꢌ + ꢄ
(4) Output voltage
(푀퐴푋)
(푀퐴푋) 퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
퐼ꢐꢒꢇ(푀퐴푋) = 퐼퐿퐸퐷(푀퐴푋) × ꢓ
× 퐼ꢐꢒꢇ(푀퐴푋)/(휂 × ꢄ퐶퐶(푀ꢅ푁)
(5) Output current
퐼퐿퐴푉퐺(푀퐴푋) = ꢄ푂푈ꢋ
)
(6) Input (inductor) average current
(푀퐴푋)
: Maximum value of IC power
consumption
: Maximum value of LED Vf
voltage
ꢨꢍ(푀퐴푋)
ꢄ푓
(푀퐴푋)
퐼ꢍꢍ(푀퐴푋)
ꢄ퐶퐶(푀퐴푋)
퐶ꢅꢆꢆ(푀퐴푋)
: Maximum value of circuit current ꢄ푓
: Minimum value of LED Vf
voltage
: Number of LED series
(푀ꢅ푁)
: Maximum value of power supply
voltage
ꢌ
: Maximum value of OUTL FET
gating capacitance
: Maximum value of DC/DC
oscillation frequency
: Maximum value of reference
voltage
: Maximum value of LED control
voltage
: Number of LED parallels
: Maximum value of LED current
per channel
: Maximum output voltage
퐼퐿퐸퐷(푀퐴푋)
ꢄ푂푈ꢋ
푓
ꢐꢆꢍ(푀퐴푋)
(푀퐴푋)
: Maximum value of output current
ꢄ푅퐸퐺(푀퐴푋)
퐼ꢐꢒꢇ(푀퐴푋)
퐼퐿퐴푉퐺(푀퐴푋)
휂
: Maximum value of input
(inductor) average current
: Efficiency (about 85 %)
ꢄ
퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
ꢓ
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
38/47
BD83A14EFV-M BD83A14MUF-M
Power Consumption Calculation Example – continued
<Calculation Example>
Calculate IC power consumption using the following conditions as an example.
퐼ꢍꢍ(푀퐴푋)
Maximum value of circuit current 10 mA
ꢓ
Number of LED parallels
4 rows
3.4 V
Maximum value of power supply
ꢄ퐶퐶(푀퐴푋)
ꢄ푓
13.5 V
Maximum value of LED Vf voltage
(푀퐴푋)
voltage
Maximum value of the OUTL pin
external FET gating capacitance
퐶ꢅꢆꢆ(푀퐴푋)
ꢄ푓
(푀ꢅ푁)
380 pF
Minimum value of LED Vf voltage
Number of LED series
3.0 V
Maximum value of
oscillation frequency
DC/DC
푓
330 kHz
5.3 V
ꢌ
8 stages
65 mA
0.85
ꢐꢆꢍ(푀퐴푋)
Maximum value of reference
voltage
Maximum value of LED control
voltage
Maximum value of LED current per
channel
ꢄ푅퐸퐺(푀퐴푋)
퐼퐿퐸퐷(푀퐴푋)
휂
ꢄ
0.84 V
Efficiency (about 85 %)
퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
From equation (3),
ꢄ푂푈ꢋ
= ꢄ푓
× ꢌ + ꢄ
(푀퐴푋)
(푀퐴푋) 퐿퐸퐷ꢍꢇ퐿(푀퐴푋)
= 3.ꢩ ꢄ × 8 + ꢃ.8ꢩ ꢄ
= ꢑ8.ꢃꢩ [V]
From equation (5),
퐼ꢐꢒꢇ(푀퐴푋) = 퐼퐿퐸퐷(푀퐴푋) × ꢓ
= ꢦꢪ 푚ꢫ × ꢩ
= ꢑꢦꢃ [mA]
Therefore, the maximum value of IC power consumption PC(MAX) is calculated as follows:
ꢨꢍ(푀퐴푋) = ꢂꢃ 푚ꢫ × ꢂ3.ꢪ ꢄ
+38ꢃ 푝ꢬ × ꢪ.3 ꢄ × 33ꢃ 푘ꢭ푧 × ꢪ.3 ꢄ
{
(
)
(
)}
+ ꢃ.8ꢩ ꢄ × ꢩ + 3.ꢩ ꢄ − 3.ꢃ ꢄ × 8 × ꢩ − ꢂ × ꢦꢪ 푚ꢫ
= ꢃ.ꢉ8 [W]
From thermal resistance θja = 34.9 °C/W, the maximum calorific value Δt(MAX) can be estimated by the following equation.
훥푡(푀퐴푋) = ꢨꢍ(푀퐴푋) × 휃푗푎 = ꢃ.ꢉ8 ꢮ × 3ꢩ.ꢉ ℃/ꢮ = 3ꢩ.ꢑ [°C]
When the ambient temperature is 85 °C, the maximum chip temperature tC(MAX) is following.
푡ꢍ(푀퐴푋) = 8ꢪ ℃ + 3ꢩ.ꢑ ℃ = ꢂꢂꢉ.ꢑ [°C]
Make sure that tC(MAX) calculated here is less than Tjmax = 150 °C.
The above is a simple calculation example only. The value of thermal resistance varies depending on the actual board
conditions and layout. Confirm the calculation here as a guide for thermal design.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
39/47
BD83A14EFV-M BD83A14MUF-M
Application Circuit Example
1 Peripheral Circuit When PMOS Is Not Used
When the load switch M1 is not required, such as when using FUSE on the input side, connect the CSH pin and inductor
L1 and open the LDSW pin.
Also, set FUSE rating to IFUSE or more.
푉
푉ꢍꢍ
퐿
ꢗꢘꢤꢠ(ꢔꢡꢢ)
(ꢔꢡꢢ) × tOCPL
퐼퐹ꢒꢆ퐸
ꢄ퐶퐶(푀퐴푋)
: FUSE rated current
: Maximum value of power supply
voltage
퐼퐹ꢒꢆ퐸
>
+
푅
ꢘ푆ꢠ(ꢔꢀꢕ)
(ꢔꢀꢕ)
: Minimum value of inductance
ꢝ(푀ꢅ푁)
푡ꢐꢍ푃퐿
ꢄꢐꢍ푃퐿(푀퐴푋)
: OCPL detect delay time (MAX = 84 ns)
: Maximum value of overcurrent
protection detect voltage
ꢈꢍꢆ퐿(푀ꢅ푁)
: Minimum value of overcurrent detect
resistor
VCC
CVCC
VREG
1
24
23
22
21
20
19
18
17
16
15
14
13
REG
VCC
CSH
CREG
M1
2
3
GND
EN
Non-
mounted
CIN
EN
LDSW
N.C.
L1
D1
VOUT
PWM
4
PWM
SYNC
SYNC
5
OUTL
CSL
COUT
M2
ROVP2
ROVP1
ADIM_P
6
ADIM_P
COMP
RT
CCOMP RCOMP
EXP-PAD
RCSL
7
PGND
PLSET
FAIL
RRT
CPLSET
8
RFAIL
RISET
VREG
VFAIL
9
ISET
LGND
LED1
LED2
10
11
12
OVP
LED4
LED3
2 Monitoring the Status of the FAIL Pin with Microcontroller
OCPH function starts operation again after stopping operation for the specified timer time. Therefore, the FAIL pin
periodically outputs the detect/release flag until the error is cleared. In the case of a system configuration that monitors the
FAIL pin with a microcontroller, there is a possibility that it will be erroneously determined as a normal state even though it
is in an abnormal state. By adding CFAIL as shown below, it is possible to fix the FAIL output to Low in an abnormal state.
VCC
CVCC
RCSH
VREG
1
2
24
23
22
21
20
19
18
17
16
15
14
13
REG
VCC
CSH
CREG
M1
GND
EN
EN
PWM
3
LDSW
N.C.
CIN
L1
D1
VOUT
4
PWM
SYNC
ADIM_P
COMP
RT
SYNC
5
OUTL
CSL
COUT
M2
ROVP2
ROVP1
ADIM_P
6
CCOMP RCOMP
EXP-PAD
RCSL
7
PGND
PLSET
FAIL
RRT
CPLSET
8
RFAIL
RISET
VREG
9
ISET
LGND
LED1
LED2
CFAIL
10
11
12
OVP
VFAIL
LED4
LED3
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
40/47
BD83A14EFV-M BD83A14MUF-M
I/O Equivalence Circuit
REG, VCC
GND, LGND, PGND
EN
VCC
PGND
EN
30 kΩ
360 kΩ
REG
GND
363 kΩ
150 kΩ
150 kΩ 150 kΩ
50 kΩ
GND
LGND
GND
PWM, SYNC, ADIM_P
COMP
RT
REG
10 kΩ
PWM
SYNC
ADIM_P
10 kΩ
10 kΩ
COM
P
RT
400 Ω
100 kΩ
GND
GND
GND
ISET
LED1 - LED4
OVP
REG
REG
OVP
GND
REG
40 kΩ
LED1
LED2
LED3
LED4
10 kΩ
10 kΩ
10 kΩ
10 kΩ
ISET
10 kΩ
650 kΩ
100 kΩ
2 Ω 200 kΩ
GND
LGND
FAIL
PLSET
CSL
REG
REG
REG
10 kΩ
12 kΩ
10 kΩ
FAIL
PLSET
10 kΩ
1 kΩ
CSL
100 kΩ
GND
GND
GND
OUTL
CSH
LDSW
REG
VCC
VCC
CSH
GND
1 pF
3 MΩ
25 kΩ
OUTL
GND
LDSW
GND
All values are Typ values.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
41/47
BD83A14EFV-M BD83A14MUF-M
Operational Notes
1. Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
2. Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at
all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic
capacitors.
3. Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4. Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5. Recommended Operating Conditions
The function and operation of the IC are guaranteed within the range specified by the recommended operating
conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical
characteristics.
6. Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.
Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing
of connections.
7. Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
8. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
9. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
www.rohm.com
TSZ02201-0T2T0B200400-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
42/47
TSZ22111 • 15 • 001
30.Nov.2022 Rev.002
BD83A14EFV-M BD83A14MUF-M
Operational Notes - continued
10. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
Pin B
B
E
C
Pin A
B
C
E
P
P+
P+
N
P+
P
P+
N
N
N
N
N
N
N
Parasitic
Elements
Parasitic
Elements
P Substrate
GND GND
P Substrate
GND
GND
Parasitic
Elements
Parasitic
Elements
N Region
close-by
Figure 36. Example of Monolithic IC Structure
11. Ceramic Capacitor
When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
12. Thermal Shutdown Circuit (TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s maximum junction temperature rating. If however the rating is exceeded for a continued period, the
junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF power output pins. When the Tj
falls below the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat
damage.
13. Over Current Protection Circuit (OCP)
This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
14. Functional Safety
“ISO 26262 Process Compliant to Support ASIL-*”
A product that has been developed based on an ISO 26262 design process compliant to the ASIL level described in
the datasheet.
“Safety Mechanism is Implemented to Support Functional Safety (ASIL-*)”
A product that has implemented safety mechanism to meet ASIL level requirements described in the datasheet.
“Functional Safety Supportive Automotive Products”
A product that has been developed for automotive use and is capable of supporting safety analysis with regard to the
functional safety.
Note: “ASIL-*” is stands for the ratings of “ASIL-A”, “-B”, “-C” or “-D” specified by each product's datasheet.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
43/47
BD83A14EFV-M BD83A14MUF-M
Ordering Information
B D 8 3 A 1
4
x
x
x
-
M E 2
Package
EFV: HTSSOP-B24
MUF: VQFN24FV4040
Product rank
M: for Automotive
Packaging and forming specification
E2: Embossed tape and reel
Marking Diagrams
HTSSOP-B24 (TOP VIEW)
VQFN24FV4040 (TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
D 8 3 A
14MUF
LOT Number
D83A14EF
Pin 1 Mark
Pin 1 Mark
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
44/47
BD83A14EFV-M BD83A14MUF-M
Physical Dimension and Packing Information
Package Name
HTSSOP-B24
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
45/47
BD83A14EFV-M BD83A14MUF-M
Physical Dimension and Packing Information - continued
Package Name
VQFN24FV4040
www.rohm.com
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
© 2022 ROHM Co., Ltd. All rights reserved.
46/47
TSZ22111 • 15 • 001
BD83A14EFV-M BD83A14MUF-M
Revision History
Date
Revision
001
Changes
New Release
P.1
08.Jul.2022
Add VQFN24FV4040 package information.
P.3
Add signal type ”O: Output signal to other units”
P.3, 4
Add Pin assign of VQFN24FV4040 package.
ADIM_P Signal Type change A to I.
P.4
Add Note 2.
P.9
Add Note1 of No.6, 7, 8 protect function.
Add Note6.
002
30.Nov.2022
P.10
Add thermal resistance of VQFN24FV4040 package.
P.22
Figure.21 X axis name change
P.25
Modify the diagram of ADIM_P input timing.
P.28
Add sentence ⑯.
P.37
Remove P.28 of P.28 PCB Application Circuit Diagram
P.46
Add physical Dimension and Packing Information of VQFN24FV4040 package.
www.rohm.com
© 2022 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0T2T0B200400-1-2
30.Nov.2022 Rev.002
47/47
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
BD83A24MUF-M (开发中)
This IC is a white LED driver for LCD backlight. It has MOS for boost and 4ch current drivers for LED drive, making it ideal for high brightness LED drive. LED pin maximum voltage is 50 V, making it suitable for driving medium LCD panels. The dimming is controlled by the PWM signal and can be set up to 20,000:1@100Hz. It also supports analog dimming and can accommodate even higher brightness ranges by combining with PWM dimming. DC/DC converters can be controlled for boost applications, and the input operating voltage range is 4.5V to 48.0V.
ROHM
©2020 ICPDF网 联系我们和版权申明