BH6504K [ROHM]
PWM driver for CD and MD players; PWM驱动程序CD和MD播放器
| 型号： | BH6504K |
| 厂家： | 
ROHM |
| 描述： | PWM driver for CD and MD players |
| 文件： | 总15页 (文件大小：270K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Optical disc ICs
PWM driver for CD and MD players
BH6504K
The BH6504K is a 4-channel PWM driver designed for CD and MD player motors and actuator drives. The power MOF-
SET output stage allows for applications with low power consumption. This IC also has a charge pump circuit and stan-
dard operational amplifier (needed for power MOSFET gate drives), and so supports a wide spectrum of applications.
FApplications
Portable CD players, MD players
FFeatures
1) Low power consumption.
5) Allowsforfree-runningandclocksynchronizationop-
eration.
2) A minimum of attached components.
3) Excellent gain precision because of the voltage feed-
back circuit.
6) Internal standard operational amplifier.
7) Internal charge pump circuit for gate drive.
8) Switchable to doubled clock synchronization.
4) Internal mute function for channel 1.
FAbsolute maximum ratings (Ta = 25_C)
FRecommended operating conditions
226
Optical disc ICs
BH6504K
FBlock diagram
227
Optical disc ICs
BH6504K
FPin descriptions
228
Optical disc ICs
BH6504K
FInput / output circuits
229
Optical disc ICs
BH6504K
230
Optical disc ICs
BH6504K
231
Optical disc ICs
BH6504K
232
Optical disc ICs
BH6504K
FElectrical characteristics
(unless otherwise noted, Ta = 25_C, Battery = 2.4V, Pre.VCC = 3.0V, VC = 1.5V, fCLK = 176.4kHz, RL = 8Ω–47µH)
233
Optical disc ICs
BH6504K
FMeasurement circuit
234
Optical disc ICs
BH6504K
FMeasurement circuit switch tables
PWM driver
DC/DC converter
Triangular wave generator
Control pin threshold
235
Optical disc ICs
BH6504K
Operational amplifier
FCircuit operation
(1) PWM driver
This is an H bridge driver with four N-type FETs in the out-
put stage. Output polarity and PWM duty vary in propor-
tion to the input differential voltage between VC, and to
the absolute value. The load is direct-PWM-driven by the
squarewavewiththisvaryingduty. Thisisavoltagefeed-
back driver and so delivers a constant gain regardless of
battery voltage variation.
(2) DC/DC convertor
The DC/DC converter that generates the voltage need-
ed to drive the FETs of the output-stage H bridge. Pre.VCC
is raised to 6.5V by attaching an inductance, Schottky
barrier diode, and capacitor.
(3) Triangular wave generator
(1) Free-running oscillation
The free-running oscillation frequency of the triangular
waves can be set with an attached resistor (Rt, between
pin 16 and the ground) and capacitor (Ct, between pin 15
and the ground). The triangular wave has an amplitude
of 3/5 Pre.VCC at the top and VF (approximately 0.7V)
at the bottom. The ratio between rise time and fall time
is 3: 1. Free-running frequency (ft) is determined with the
following equation:
3
4
1
ft=
S
VF
Ct S Rt 1 *
3
5
Pre.Vcc
236
Optical disc ICs
BH6504K
(2) Clock synchronization
S The PWM driver is a voltage feedback driver, which
should preclude any problems unless the setting is such
that the triangular wave has an extremely small ampli-
tude.
The triangular wave can be synchronized by inputting to
the CLK pin (pin17) a pulse wave equal to 0–Pre.VCC (Vp-
p). The following precautions should be kept in mind:
S The amplitude of the triangular wave decreases as the
clock frequency rises.
S As mentioned above, a capacitor and resistor are also
required during clock synchronization.
(3) Using the ESP pin
1. To operate the PWM driver at 176.4kHz
2. To operate the PWM driver at 88.2kHz
237
Optical disc ICs
BH6504K
FApplication example
238
Optical disc ICs
BH6504K
FOperation notes
Attach a bypass capacitor (roughly 1µF) to the power supply, at the base of the IC.
FElectrical characteristic curves
239
Optical disc ICs
BH6504K
FExternal dimensions (Units: mm)
240
相关型号：
©2020 ICPDF网 联系我们和版权申明