BR25H640F-2ACE2 [ROHM]
Operation SPI BUS EEPROM;型号: | BR25H640F-2ACE2 |
厂家: | ROHM |
描述: | Operation SPI BUS EEPROM 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 时钟 光电二极管 内存集成电路 |
文件: | 总40页 (文件大小:1569K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
Serial EEPROM Series Automotive EEPROM
125°C Operation SPI BUS EEPROM
BR25H640-2AC
General Description
BR25H640-2AC is a 64Kbit Serial EEPROM of SPI BUS interface method.
Features
Packages W(Typ) x D(Typ) x H(Max)
■ SPI BUS interface (CPOL, CPHA)=(0,0), (1,1)
■ Voltage Range
: 2.5V to 5.5V
: -40°C to +125°C
: 10MHz(Max)
: 4ms(Max)
■ Operating Range
■ Clock Frequency
■ Write Time
■ Page Size
: 32bytes
■ Bit Format
: 8192 x 8bit
MSOP8
TSSOP-B8
■ 32bytes Write Lockable Identification Page (ID Page)
■ Address Auto Increment Function at Read Operation
■ Auto Erase and Auto End Function at Data Rewrite
■ Write Protect Block Setting by Software
Memory Array 1/4, 1/2, Whole
2.90mm x 4.00mm x 0.90mm 3.00mm x 6.40mm x 1.20mm
■ HOLD Function by HOLDB Pin
■ Low Supply Current
Write Operation (5V) : 1.0mA (Typ)
Read Operation (5V) : 1.2mA (Typ)
Standby State(5V)
■ Prevention of Write Mistake
Write prohibition at Power On
: 0.1μA (Typ)
SOP8
5.00mm x 6.20mm x 1.71mm 4.90mm x 6.00mm x 1.65mm
SOP-J8
Write prohibition by WPB Pin
Write prohibition Block Setting
Prevention of Write Mistake at Low Voltage
■ Write Cycles
: 1,000,000 Write Cycles (Ta≤85°C)
:
:
500,000 Write Cycles (Ta≤105°C)
300,000 Write Cycles (Ta≤125°C)
■ Data Retention : 100 Years (Ta≤25°C)
: 60 Years (Ta≤105°C)
: 50 Years (Ta≤125°C)
■ Data at Shipment
Memory Array
ID Page
:FFh
:2Fh, 00h, 0Dh
:FFh
First 3 Addresses
Other Addresses
Status Register WPEN, BP1, BP0 :0, 0, 0
Lock Status LS :0
■ MSOP8, TSSOP-B8, SOP8, SOP-J8 Packages
■ AEC-Q100 Qualified
〇Product structure : Silicon monolithic integrated circuit 〇This product has no designed protection against radioactive rays
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
1/36
Daattaasshheeeett
BR25H640-2AC
Absolute Maximum Ratings (Ta=25°C)
Parameter
Symbol
Rating
-0.3 to +6.5
Unit
V
Supply Voltage
Vcc
0.38 (MSOP8) (Note1)
0.41 (TSSOP-B8) (Note2)
0.56 (SOP8) (Note3)
0.56 (SOP-J8) (Note4)
-65 to +150
Power Dissipation
Pd
W
Storage Temperature Range
Operating Temperature Range
Terminal Voltage
Tstg
Topr
-
°C
°C
V
-40 to +125
-0.3 to +6.5
Maximum Junction Temperature
Tjmax
VESD
150
°C
V
Electrostatic Discharge Voltage
(Human Body Model)
-6000 to +6000
(Note1) Derate by 3.1mW/°C when operating above Ta=25°C
(Note2) Derate by 3.3mW/°C when operating above Ta=25°C.
(Note3) Derate by 4.5mW/°C when operating above Ta=25°C.
(Note4) Derate by 4.5mW/°C when operating above Ta=25°C.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Memory Cell Characteristics (Vcc=2.5V to 5.5V)
Limit
Parameter
Unit
Condition
Min
Typ
Max
1,000,000
-
-
Cycles
Cycles
Cycles
Years
Years
Years
Ta≤85°C
Ta≤105°C
Ta≤125°C
Ta≤25°C
Ta≤105°C
Ta≤125°C
Write Cycles (Note5, 6)
500,000
300,000
100
-
-
-
-
-
-
-
-
-
-
Data Retention (Note5)
60
50
(Note5) Not 100% TESTED
(Note6) The Write Cycles is defined for unit of 4 data bytes with the same address bits of A12 to A2.
Recommended Operating Ratings
Rating
Parameter
Supply Voltage
Symbol
Unit
Min
2.5
Max
5.5
Vcc
VIN
C
V
V
Input Voltage
0
Vcc
Bypass Capacitor
0.1
-
μF
Input / Output Capacitance (Ta=25°C, Frequency=5MHz)
Parameter
Symbol
Conditions
Min
-
Max
8
Unit
pF
Input Capacitance (Note7)
CIN
VIN=GND
Output Capacitance (Note7)
COUT
VOUT=GND
-
8
pF
(Note7) Not 100% TESTED
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
2/36
Daattaasshheeeett
BR25H640-2AC
DC Characteristics (Unless otherwise specified, Ta=-40°C to +125°C, Vcc=2.5V to 5.5V)
Limit
Parameter
Symbol
Unit
Conditions
Min
0.7 Vcc
-0.3
0
Typ
-
-
-
-
-
-
Max
Vcc+0.3
0.3 Vcc
0.4
Input High Voltage
Input Low Voltage
Output Low Voltage
Output High Voltage
VIH
VIL
VOL
VOH
ILI
V
V
2.5V≤Vcc≤5.5V
2.5V≤Vcc≤5.5V
IOL=2.1mA
V
0.8 Vcc
-2
Vcc
V
IOH=-2.0mA
Input Leakage
Current
+2
μA
μA
VIN=0V to Vcc
Output Leakage
Current
ILO
-2
+2
VOUT=0V to Vcc, CSB=Vcc
Vcc=2.5V, fSCK=5MHz, tE/W=4ms
VIH/VIL=0.9Vcc/0.1Vcc, SO=OPEN
ICC1
ICC2
ICC3
ICC4
ICC5
ISB
-
-
-
-
-
-
-
-
-
-
-
-
2.5
5.5
1.5
2.0
4.0
10
mA
mA
mA
mA
mA
μA
Supply Current
(WRITE)
Vcc=5.5V, fSCK=5 or 10 MHz, tE/W=4ms
VIH/VIL=0.9Vcc/0.1Vcc, SO=OPEN
Vcc=2.5V, fSCK=5MHz
VIH/VIL=0.9Vcc/0.1Vcc, SO=OPEN
Supply Current
(READ)
Vcc=5.5V, fSCK=5MHz
VIH/VIL=0.9Vcc/0.1Vcc, SO=OPEN
Vcc=5.5V, fSCK=10MHz
VIH/VIL=0.9Vcc/0.1Vcc, SO=OPEN
Vcc=5.5V
CSB=HOLDB=WPB=Vcc,
SCK=SI=Vcc or 0V, SO=OPEN
Standby Current
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
3/36
Daattaasshheeeett
BR25H640-2AC
AC Characteristics (Ta=-40°C to +125°C, unless otherwise specified, load capacitance CL1=100pF)
2.5V≤Vcc≤5.5V
4.5V≤Vcc≤5.5V
Parameter
Symbol
Unit
Min
Typ
-
-
-
-
-
-
-
-
-
-
-
Max
Min
Typ
-
-
-
-
-
-
-
-
-
-
-
Max
SCK Frequency
fSCK
tSCKWH
tSCKWL
tCS
0.01
85
85
85
90
85
90
90
20
30
-
5
0.01
40
40
40
30
30
30
30
10
10
-
10
-
-
-
-
-
-
-
-
-
40
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SCK High Time
SCK Low Time
CSB High Time
CSB Setup Time
CSB Hold Time
SCK Setup Time
SCK Hold Time
SI Setup Time
-
-
-
-
-
-
-
-
-
60
tCSS
tCSH
tSCKS
tSCKH
tDIS
SI Hold Time
tDIH
Data Output Delay Time1
tPD1
Data Output Delay Time2
(CL2=30pF)
tPD2
-
-
50
-
-
30
ns
Output Hold Time
tOH
tOZ
0
-
-
-
0
-
-
-
ns
ns
Output Disable Time
-
100
-
40
HOLDB Setting
Setup Time
HOLDB Setting
Hold Time
HOLDB Release
Setup Time
HOLDB Release
Hold Time
Time from HOLDB
to Output High-Z
Time from HOLDB
to Output Change
tHFS
tHFH
tHRS
tHRH
tHOZ
tHPD
0
-
-
-
-
-
-
-
-
0
-
-
-
-
-
-
-
-
-
-
40
40
ns
ns
ns
ns
ns
ns
40
0
30
0
-
70
-
-
-
30
-
-
100
60
SCK Rise Time (Note1)
SCK Fall Time (Note1)
Output Rise Time (Note1)
Output Fall Time (Note1)
tRC
tFC
-
-
-
-
-
-
-
-
-
-
2
2
-
-
-
-
-
-
-
-
-
-
2
2
μs
μs
ns
ns
ms
tRO
tFO
tE/W
40
40
4
20
20
4
Write Time
(Note1) NOT 100% TESTED
AC Measurement Conditions
Limit
Parameter
Symbol
Unit
Min
-
Typ
-
Max
100
30
Load Capacitance1
Load Capacitance2
Input Rise Time
Input Fall Time
CL1
CL2
-
pF
pF
ns
ns
V
Input Voltage
Input / Output Voltage
-
-
0.8Vcc
0.7Vcc
-
-
50
-
-
-
50
0.3Vcc
0.2Vcc
Input Voltage
-
0.2 Vcc / 0.8 Vcc
0.3 Vcc / 0.7 Vcc
Input / Output
Judgment Voltage
-
V
Figure 1. Input / Output Judgment Voltage
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
4/36
Daattaasshheeeett
BR25H640-2AC
Serial Input / Output Timing
tCSS
tCS
CSB
tSCKS
tRC
tFC
tSCKWH
tSCKWL
tDIS
SCK
tDIH
SI
High-Z
SO
Figure 2. Input Timing
SI is taken into IC inside in sync with data rise edge of SCK. Input address and data from the Most Significant Bit MSB.
tCS
tSCKH
CSB
tCSH
SCK
SI
tPD
tRO,tFO
tOZ
tOH
High-Z
SO
Figure 3. Input / Output Timing
SO is output in sync with data fall edge of SCK. Data is output from the Most Significant Bit MSB.
"H"
CSB
"L"
tHFS tHFH
tHRS tHRH
SCK
SI
tDIS
n
n+1
n-1
tHOZ
Dn
tHPD
High-Z
SO
Dn+1
Dn
Dn-1
HOLDB
Figure 4. HOLD Timing
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
5/36
Daattaasshheeeett
BR25H640-2AC
Block Diagram
VOLTAGE
CSB
SCK
INSTRUCTION DECODE
CONTROL CLOCK
GENERATION
DETECTION
HIGH VOLTAGE
GENERATOR
WRITE
INHIBITION
SI
INSTRUCTION
REGISTER
IDENTIFICATION PAGE
STATUS REGISTER
ADDRESS
HOLDB
ADDRESS
13bit
8bit
13bit
8bit
REGISTER
DECODER
64Kbit
EEPROM
DATA
READ/WRITE
AMP
WPB
SO
REGISTER
Figure 5. Block Diagram
Pin Configuration
Vcc HOLDB SCK
SI
BR25H640-2AC
CSB
SO
WPB
GND
Figure 6. Pin Assignment Diagram
Pin Description
Pin
Number
Pin
Name
Input
/ Output
Function
1
CSB
SO
Input
Chip Select Input
2
3
4
5
6
Output
Input
-
Serial Data Output
Write Protect Input
WPB
GND
SI
Write Status Register Command is prohibited.
All Input / Output Reference Voltage, 0V
Serial Data Input
Start Bit, Instruction Code, Address and Data Input
Input
Input
SCK
Serial Clock Input
Hold Input
7
8
HOLDB
Vcc
Input
Serial Communications may be suspended
temporarily (HOLD State).
-
Supply Voltage
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
6/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves
6.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
5.0
4.0
3.0
2.0
1.0
0.0
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLYVOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 7. Input High Voltage VIH
(CSB, SCK, SI, HOLDB, WPB)
Figure 8. Input Low Voltage VIL
(CSB, SCK, SI, HOLDB, WPB)
1.0
0.8
0.6
0.4
0.2
0.0
3.0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
2.5
2.0
1.5
1.0
0.5
0.0
SPEC
SPEC
Ta=
Ta=
Ta=
-40°C
25°C
125°C
-6
-5
-4
-3
-2
-1
0
0
1
2
3
4
5
6
OUTPUT LOW CURRENT : IOL mA
OUTPUT HIGH CURRENT : IOH mA
[ ]
[
]
Figure 9. Output Low Voltage VOL, IOL (Vcc=2.5V)
Figure 10. Output High Voltage VOH, IOH (Vcc=2.5V)
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
7/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
3.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
2.5
2.0
1.5
1.0
0.5
0.0
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLYVOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 11. Input Leakage Current ILI
(CSB, SCK, SI, HOLDB, WPB)
Figure 12. Output Leakage Current ILO
(SO)
2.5
6.0
SPEC
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
5.0
4.0
3.0
2.0
1.0
0.0
2.0
1.5
1.0
0.5
0.0
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLYVOLTAGE : Vcc V
[ ]
Figure 13. Supply Current (WRITE) ICC1,2
Figure 14. Supply Current (READ) ICC3,4
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
8/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
6.0
12
10
8
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
5.0
4.0
3.0
2.0
1.0
0.0
SPEC
6
4
2
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 16. Standby Current ISB
Figure 15. Supply Current (READ) ICC5
100
80
60
40
20
0
100
10
1
SPEC
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
SPEC
Ta=
Ta=
Ta=
-40°C
25°C
125°C
0.1
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLYVOLTAGE : Vcc V
[ ]
Figure 17. SCK Frequency fSCK
Figure 18. SCK High Time
tSCKWH
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
9/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
100
100
80
60
40
20
0
SPEC
SPEC
80
Ta=
Ta=
Ta=
Ta=
Ta=
-40°C
25°C
125°C
-40°C
25°C
Ta= 125°C
60
40
20
0
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 20. CSB High Time tCS
Figure 19. SCK Low Time tSCKWL
100
80
60
40
20
0
100
80
60
40
20
0
SPEC
SPEC
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 21. CSB Setup Time tCSS
Figure 22. CSB Hold Time
tCSH
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
10/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
50
50
40
30
20
10
0
Ta=
Ta=
Ta=
Ta=
Ta=
Ta=
-40°C
25°C
125°C
-40°C
25°C
125°C
40
30
20
10
0
SPEC
SPEC
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 24. SI Hold Time tDIH
Figure 23. SI Setup Time tDIS
100
80
60
40
20
0
100
80
60
40
20
0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 25. Data Output Delay Time1 tPD1 (CL1=100pF)
Figure 26. Data Output Delay Time2 tPD2 (CL2=30pF)
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
11/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
120
50
40
30
20
10
0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
100
80
60
40
20
0
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLY VOLTAGE : Vcc V
[ ]
Figure 27. Output Disable Time tOZ
Figure 28. HOLDB Setting Hold Time tHFH
100
80
60
40
20
0
120
100
80
60
40
20
0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
[ ]
SUPPLYVOLTAGE : Vcc V
[ ]
Figure 29. HOLDB Release Hold Time tHRH
Figure 30. Time from HOLDB to Output High-Z tHOZ
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
12/36
Daattaasshheeeett
BR25H640-2AC
Typical Performance Curves - continued
100
100
80
60
40
20
0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
80
60
40
20
0
SPEC
SPEC
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
SUPPLY VOLTAGE : Vcc V
[ ]
[ ]
Figure 31. Time from HOLDB to Output Change tHPD
Figure 32. Output Rise Time tRO
8
6
4
2
0
100
80
60
40
20
0
Ta=
Ta=
Ta=
-40°C
25°C
125°C
Ta=
Ta=
Ta=
-40°C
25°C
125°C
SPEC
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SUPPLY VOLTAGE : Vcc V
SUPPLY VOLTAGE : Vcc V
[ ]
[ ]
Figure 33. Output Fall Time tFO
Figure 34. Write Time tE/W
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
13/36
Daattaasshheeeett
BR25H640-2AC
1. Features
(1) Status Register
This IC has the Status Registers. Status Registers are of 8 bits and express the following parameters.
WPEN, BP0 and BP1 can be set by Write Status Register command. These 3 bits are memorized into the EEPROM,
therefore are valid even when supply voltage is turned off.
Write Cycles and Data Retention of Status Registers are same as characteristics of the EEPROM.
WEN can be set by Write Enable command and Write Disable command. WEN becomes write disable status when
――
supply voltage is turned off. R/B is for write confirmation, therefore cannot be set externally.
The values of Status Register can be read by Read Status Register command.
Table 1. Status Register
D7
D6
D5
D4
0
D3
D2
D1
D0
――
WPEN
0
0
BP1
BP0
WEN
R/B
Table 2. Function of Status Register
Memory
Location
bit
Function
Content
Pin Enable / Disable designation bit
WPEN bit enables / disables the function of WPB
pin.
WPEN EEPROM
for WPB pin
WPEN=0=Invalid, WPEN=1=Valid
BP1 and BP0 bits designate the Write Disable
Block of EEPROM.
Refer Table 3. Write Disable Block Setting.
BP1
EEPROM Write Disable Block
designation bit
EEPROM
BP0
Write Enable/Write Disable Confirmation bit
WEN bit indicates the status of write enable or
write disable for WRITE, WRSR, WRID, LID.
WEN
Register
Register
for WRITE, WRSR, WRID and LID
WEN=0=Prohibited, WEN=1=Permitted
Write Cycle Status(―R―E―A――D―Y―/BUSY)
Confirmation bit
――
――
R/B bit indicates the status of READY or BUSY of
the write cycle.
R/B
――
――
R/B=0=READY , R/B=1=BUSY
Table 3. Write Disable Block Setting
Status Register
Protected Block
Protected Addresses
BP1
0
BP0
0
None
None
0
1
1
1
0
1
Upper 1/4
1800h to 1FFFh
Upper 1/2
1000h to 1FFFh
Whole Memory
0000h to 1FFFh, ID Page
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
14/36
Daattaasshheeeett
BR25H640-2AC
(2) Write Protect Mode by WPB pin
By setting WPB = Low with WPEN = 1, Write Status Register command is disabled. Only when WPEN bit is set “1”,
the WPB pin functions become valid. However, when write cycle is in execution, no interruption can be made.
Table 4. Write Protect Mode
Instruction
WPEN bit
WPB pin
WRSR
Writable
WRITE/WRID/LID
Writable
0
1
1
X
1
0
Writable
Writable
Write Protected
Writable
WPB is normally fixed to High or Low for use, but when WPB is controlled so as to cancel Write Status Register
command, pay attention to the following WPB Valid Timing.
Write Status Register command is executed, by setting WPB = Low in cancel valid area, command can be cancelled.
The Data area (from 7th fall of SCK to 16th rise of SCK) becomes the cancel valid area. However, once write is started,
any input cannot be cancelled. WPB input becomes Don’t Care, and cancellation becomes invalid.
CSB
SCK
6
7
15
16
tE/W
Instruction
Instruction Code
Data
Valid
Data Write Time
Write Protect
Invalid
Invalid
Figure 35. WPB Valid Timing (WRSR)
(3) Hold Mode by HOLDB pin
By the HOLDB pin, serial communication can be stopped temporarily (HOLD status). HOLDB pin carries out serial
communications normally when it is High. To get in HOLD status, at serial communication, when SCK = Low, set the
HOLDB pin Low. At HOLD status, SCK and SI become Don’t Care, and SO becomes high impedance (High-Z). To
release the HOLD status, set the HOLDB pin High when SCK = Low. After that, communication can be restarted from
the point before the HOLD status. For example, when HOLD status is made after A5 address input at Read command,
after release of HOLD status, by starting A4 address input, Read command can be restarted. When in HOLD status,
leave CSB = Low. When it is set CSB = High in HOLD status, the IC is reset, therefore communication after that
cannot be restarted.
SCK
HOLDB
HOLD Status
HOLD Status
Figure 36. HOLD Status
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
15/36
Daattaasshheeeett
BR25H640-2AC
(4) ID Page
This IC has 32 bytes Write lockable Identification Page (ID Page) in addition to Memory Array.
The data in the first 3 addresses are for device identification. These data are over written by Write ID Page command.
Table 5. Data in the first 3 addresses
ID Page Address
Data
2Fh
00h
0Dh
Content
00h
01h
02h
Manufacturer Code (ROHM)
Interface Method (SPI)
Memory Density (64Kbit)
By setting Lock Status (LS) bit to “1” with Lock ID Page command, it is prohibited to write to ID page permanently.
It is not reversible to set from ID Page Lock Status (LS=”1”) to ID Page Lock Release status (LS=”0”).
Table 6. Function of Lock Status
Memory
bit
Function
Content
Location
ID Page Lock/ Lock Release Status designation bit
LS=0=ID Page Lock Release
LS bit can set Lock Status to
ID Page.
LS
EEPROM
LS=1=ID Page Lock
(5) ECC Function
This IC has ECC bits for Error Correction to each 4 data bytes with the same address bits of A12 to A2. In the Read
operation, even if there is 1 bit data error in the 4 bytes, IC corrects to correct data by ECC function and outputs data
corrected. Even if write operation is started with only 1 byte data input, this IC rewrites the data of 4 bytes with the
same address bits of A12 to A2 and the data of ECC bits added to these 4 bytes data. In order to maximize Write
Cycles specified, it is recommended to write with data input of each 4 bytes with the same address bits of A12 to A2.
Table 7. Example of 4 data bytes with the same address bits of A12 to A2 (Address 0000h,0001h,0002h,0003h)
Non-
Common
Same Address Bits from A12 to A2
Address
A12 A11 A10
A9
0
0
0
0
A8
0
0
0
0
A7
0
0
0
0
A6
0
0
0
0
A5
0
0
0
0
A4
0
0
0
0
A3
0
0
0
0
A2
0
0
0
0
A1
0
0
1
1
A0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0000h
0001h
0002h
0003h
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
16/36
Daattaasshheeeett
BR25H640-2AC
2. Instruction Mode
After setting CSB pin from High to Low, to execute each command, input Instruction Code, Address and Data from the
Most Significant Bit MSB.
Table 8. Instruction Mode
Instruction
Code (8bit)
Address(MSB) / Data
(8bit)
Address (LSB)
(8bit)
Data
(8bit)
Instruction
WREN
WRDI
READ
WRITE
RDSR
WRSR
RDID
Content
Write Enable
Write Disable
Read
0000 0110
0000 0100
0000 0011
0000 0010
0000 0101
0000 0001
1000 0011
1000 0010
1000 0011
1000 0010
-
-
-
-
-
-
A15 to A8 (Note1)
A15 to A8 (Note1)
D7 to D0 Output (Note2)
D7 to D0 Input (Note2)
0000 0000
A7 to A0
A7 to A0
-
D7 to D0 Output
D7 to D0 Input
-
Write
Read Status
Register
Write Status
Register
-
-
Read ID Page
Write ID Page
Read Lock Status
Lock ID page
00A4 to A0
00A4 to A0
0000 0000
0000 0000
D7 to D0 Output
D7 to D0 Input
WRID
RDLS
LID
0000 0000
D7 to D0 Output
0000 0100
(Note3)
D7 to D0 Input
0000 0100
(Note3)
(Note1) Address bit A15, A14, A13 = Don’t Care
(Note2) Refer Figure 43. , Figure 44..
(Note3) Refer Figure 47. , Figure 48..
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
17/36
Daattaasshheeeett
BR25H640-2AC
3. Timing Chart
(1) Write Enable Command (WREN)
It is set to write enable status by Write Enable command. As for this command, set CSB to Low, and then input the
Instruction Code of Write Enable command. This command is accepted at the 7th rise of SCK. Even with input over 7
clocks, command becomes valid.
Before carrying out Write command, Write Status Register command, Write ID Page command and Lock ID Page
command, it is necessary to set write enable status by the Write Enable command.
CSB
0
1
2
3
4
5
6
7
SCK
SI
0
0
0
0
0
1
1
0
High-Z
SO
Figure 37. Write Enable Command
(2) Write Disable Command (WRDI)
It is set to write disable status, WEN bit becomes to “0”, by Write Disable command. As for this command, set CSB to
Low, and then input the Instruction Code of Write Disable command. This command is accepted at the 7th rise of SCK.
Even with input over 7 clocks, command becomes valid.
If Write command, Write Status Register command, Write ID Page command or Lock ID Page command is input in the
write disable status, commands are cancelled. And even in the write enable status, once Write command, Write Status
Register command, Write ID Page command or Lock ID Page is executed, it gets in the write disable status.
After power on, this IC is in write disable status.
CSB
0
1
2
3
4
5
6
7
SCK
SI
0
0
0
0
0
1
0
0
High-Z
SO
Figure 38. Write Disable Command
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
18/36
Daattaasshheeeett
BR25H640-2AC
(3) Read Command (READ)
By Read command, data of EEPROM can be read. As for this command, set CSB to Low, then input address after
Instruction Code of Read command. This IC starts data output of the designated address. Data output is started from
SCK fall of 23 clock, and from D7 to D0 sequentially. This IC has increment read function. After output of data for 1
byte (8bits), by continuing input of SCK, data of the next address can be read. Increment read can read all the
addresses of EEPROM Array. After reading data of the most significant address, by continuing increment read, data of
the least significant address is read.
CSB
SCK
SI
~~
~~
~~
~~
0
1
2
3
4
5
6
7
8
9
10
11
23
24
30
31
Instruction Code(8bit)
Address Input (16bit)
~~
0
0
0
0
0
0
1
1
X
X
X
A12
A1 A0
~~
second byte
Data Outputs of first byte (8bit)
~~
High-Z
~~
SO
D7 D6
D2 D1 D0 D7
X =Don’t Care
Figure 39. Read Command
(4) Write Command (WRITE)
By Write command, data of EEPROM can be written. As for this command, set CSB to Low, then input address and
data after Instruction Code of Write command. Then, by making CSB to High, the IC starts write operation. The write
time of EEPROM requires time of tE/W (Max 4ms). To start write operation, set CSB Low to High after taking the last
data (D0), and before the next SCK clock starts. At other timing, Write command is not executed, and this Write
command is cancelled.
During write operation, other than Read Status Register command is not accepted.
This IC has Page Write function, and after input of data for 1 byte (8bits), by continuing data input without setting CSB
Low to High, data up to 32 bytes can be written for one tE/W. In Page Write, the addressed lower 5 address bits are
incremented internally at every time when data of 1 byte is inputted and data is written to respective addresses. When
the data input exceeds the last address byte of the page, address rolls over to the first address byte of the same page.
It is not recommended to input data over 32 bytes, it is recommended to input data in 32 bytes. In case of the data
input over 32 bytes, it is explained in Table 10.
CSB rising valid timing to start write operation
CSB
SCK
~~
~~
~~
0
1
2
3
4
5
6
7
8
9
11
23
24
30
31
32
10
~~
Instruction Code (8bit)
Address Input (16bit)
~~
Data Input (8bit)
~~
X
X
0
0
0
0
0
0
1
0
X
A12
A1
A0
D7 D6
D2
~~
D1
D0
SI
~~
High-Z
~~
SO
X=Don't Care
Figure 40. Write Command (Byte Write)
CSB rising valid timing to start writeoperation
CSB
SCK
~~
~~
~~
~~
(8n+24)-8(8n+24)-7(8n+24)-2(8n+24)-1
8n+24
9
0
1
2
3
4
5
6
7
8
10
11
23
24
25
30
31
32
33
~~
Instruction Code (8bit)
Address Input (16bit)
Data Input of first byte (8bit)
Data Input of nth byte
~~
~~
~~
A12
D7
D6
D0
0
0
0
0
0
0
1
0
X
X
X
A1
A0
D7 D6
D1
~~
D0 D7
D6
SI
~~
High-Z
~~
SO
X=Don’t care
Figure 41. Write Command (Page Write)
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
19/36
Daattaasshheeeett
BR25H640-2AC
(a) Page Write Function
32 bytes of Page
Column 0
0000h
0020h
0040h
・
Column 1
0001h
0021h
0041h
・
Column 2
・・・
・・・
・・・
・・・
・
Column 30 Column 31
Page 0
Page 1
Page 2
0002h
0022h
0042h
・
001Eh
003Eh
005Eh
・
001Fh
003Fh
005Fh
・
・
・
Page 254
Page 255
・
・
・
・
・
・
1FC0h
1FE0h
1FC1h
1FE1h
1FC2h
1FE2h
・・・
・・・
1FDEh
1FFEh
1FDFh
1FFFh
These column addresses are
the first address of each pages.
These column addresses are
the last address of each pages.
Figure 42. EEPROM physical address for Page Write command (32Byte)
● In case of Page Write command with lower than 32 bytes data input
Table 9. Example of Page Write with 2 bytes data input
4 bytes group
Group 0
・・・
・・・
・・・
Group 7
001Ch 001Dh 001Eh 001Fh
No.
Addresses of Page 0
0000h
00h
0001h
0002h
02h
0003h
03h
0004h
①
②
③
Previous Data
01h
55h
55h
04h
-
・・・
・・・
・・・
1Ch
-
1Dh
-
1Eh
-
1Fh
-
Input data for
Page Write (2 bytes)
AAh
AAh
-
-
The Data
after Write operation
02h
03h
04h
1Ch
1Dh
1Eh
1Fh
No.① :These data are EEPROM data before Write operation.
No.② :Inputted 2 bytes data AAh, 55h from address 0000h.
No.③ :If Write operation is executed with the data of No.②, the data are changed from the data of No.① to the
data of No.③.
The data of address 0000h, 0001h are changed to data AAh, 55h, the data of address 0002h, 0003h, the 4
bytes group of Group 0, are over-written to data 02h, 03h.
When Write command is cancelled, EEPROM data keep No.①.
● In case of Page Write command with more than 32 bytes data input
Table 10. Example of Page Write with 34 bytes data input
4 bytes group
Group 0
・・・
・・・
・・・
Group 7
No.
Addresses of Page 0
0000h
00h
0001h
0002h
02h
55h
-
0003h
03h
AAh
-
0004h
001Ch 001Dh 001Eh 001Fh
①
Previous Data
01h
AAh
00h
00h
04h
55h
-
・・・
・・・
・・・
・・・
1Ch
55h
-
1Dh
AAh
-
1Eh
55h
-
1Fh
AAh
-
55h
Input data for
Page Write (34 bytes)
②
③
FFh
The Data
after Write operation
FFh
02h
03h
55h
55h
AAh
55h
AAh
No.① :These data are EEPROM data before Write operation.
No.② :Inputted 34 bytes data 55h, AAh, ・・・・, 55h, AAh, FFh, 00h from address 0000h.
The data of address 0000h, 0001h are set to data 55h, AAh first. The data of address 0002h, 0003h are
set to data 55h, AAh. After inputting data to Maximum byte (001Fh), the data address 0000h, 0001h are
set to data FFh, 00h again. No data input to address 0002h, 0003h again.
No.③ :If Write operation is executed with the data of No.②, the data are changed from the data of No.① to the
data of No.③.
The data of address 0000h, 0001h are changed to FFh, 00h inputted data later, not to 55h, AAh inputted
data first. The data of address 0002h, 0003h, the 4 bytes group of Group 0, are over-written to 02h, 03h of
Previous Data, not to 55h, AAh inputted data first. The data of other addresses are changed to 55h,
AAh・・・・, 55h, AAh.
When Write command is cancelled, EEPROM data keep No.①.
● Roll Over
In Page Write command, when data is set to the last address of a page (e.g. address “001Fh” of page 0), the next
data will be set to the first address of the same page (e.g. address “0000h” of page 0). This is why Page Write
address increment is available in the same page.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
20/36
Daattaasshheeeett
BR25H640-2AC
(5) Read Status Register Command (RDSR)
By Read Status register command, data of status register can be read. As for this command, set CSB to Low, then
input Instruction Code of Read Status Register command. This IC starts data output of the status register. Data output
is started from SCK fall of 7 clock, and from D7 to D0 sequentially. This IC has increment read function. After output of
data for 1 byte (8bits), by continuing input of SCK, this IC repeats to output data of the status register.
Even if in write operation, Read Status Register command can be executed.
CSB
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
Instruction Code (8bit)
0
0
0
0
0
1
0
1
SI
Data Output (8bit)
D7
D6
D5
0
D4
D3
D2
D1
WEN
D0
R/B
High-Z
W PEN
BP1 BP0
SO
0
0
Figure 43. Read Status Register Command
(6) Write Status Register Command (WRSR)
Write Status Register command can write status register data. The data can be written by this command are 3 bits,
that is, WPEN (D7), BP1 (D3) and BP0 (D2) among 8 bits of status register. As for this command, set CSB to Low,
and input Instruction Code of Write Status Register command, and input data. Then, by making CSB to High, this IC
starts write operation. Write Time requires time of tE/W as same as Write command. As for CSB rise, start CSB after
taking the last data bit (D0), and before the next SCK clock starts. At other timing, command is cancelled.
To the write disabled block, write cannot be made, and only read can be made.
During write operation, other than Read Status Register command is not accepted.
CSB
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SCK
Data Output (8bit)
Instruction Code (8bit)
D7
WPEN
D6
D5
X
D4
X
D3
D2
D1
D0
0
0
0
0
0
0
0
1
X
BP1 BP0
X
X
SI
High-Z
SO
X=Don't care
Figure 44. Write Status Register Command
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
21/36
Daattaasshheeeett
BR25H640-2AC
(7) Read ID Page Command (RDID)
By Read ID Page command, data of ID Page can be read. As for this command, set CSB to Low, then input address
after Instruction Code of Read ID Page command. Input address bit A10 as “0”, other upper address bits A12 to A6 as
“0”. By inputting lower address bits A4 to A0, it is possible to address to 32 bytes ID Page. Data output is started from
SCK fall of 23 clock, and from D7 to D0 sequentially. This IC has increment read function. After output of data for 1
byte (8bits), by continuing input of SCK, data of the next address can be read. After reading data of the most
significant address of ID Page, by continuing increment read, data of the least significant address of ID Page is read.
CSB
~~
~~
~~
~~
31
0
1
2
3
4
5
6
7
8
9
10
11
23
24
30
SCK
SI
Instruction Code(8bit)
Address Input (16bit)
~~
0
1
0
0
0
0
1
1
0
0
0
A12
A1 A0
~~
second byte
D7
Data Outputs of first byte (8bit)
~~
~~
High-Z
SO
D7 D6
D2 D1 D0
Figure 45. Read ID Page Command
(8) Write ID Page Command (WRID)
By Write ID Page command, data of ID Page can be written. As for this command, set CSB to Low, then input address
and data after Instruction Code of Write ID Page command. Input address bit A10 as “0”, other upper address bits A12
to A6 as “0”. By inputting lower address bits A4 to A0, it is possible to address to 32 bytes ID Page. Then, by making
CSB to High, the IC starts write operation. To start write operation, set CSB Low to High after taking the last data (D0),
and before the next SCK clock starts. At other timing, Write ID Page command is not executed, and this Write ID Page
command is cancelled. The write time of EEPROM requires time of tE/W (Max 4ms).
During write operation, other than Read Status Register command is not accepted.
In case of Lock Status (LS) bit “1”, Write ID Page command can’t be executed.
Write ID Page command has Page Write Function same as Write command.
CSB rising valid timing to start write operation
CSB
~~
0
1
2
3
4
5
6
7
8
9
10
11
23
24
30
31
32
SCK
~~
Instruction Code (8bit)
Data Input (8bit)
Address Input (16bit)
~~
~~
~~
0
1
0
0
0
0
0
1
0
0
0
A12
A1
A0
D7 D6
D2
~~
D1 D0
SI
High-Z
~~
SO
Figure 46. Write ID Page Command
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
22/36
Daattaasshheeeett
BR25H640-2AC
(9) Read Lock Status Command (RDLS)
By Read Lock Status command, data of Lock Status can be read. As for this command, set CSB to Low, then input
address after Instruction Code of Read Lock Status command. Input address bit A10 as “1”, other address bits A12 to
A0 as “0”. Data output is started from SCK fall of 23 clock, and from D7 to D0 sequentially. The data D0 indicates Lock
Status bit. The data D7 to D1 are Don’t Care. This IC has increment read function. After output of data for 1 byte
(8bits), by continuing input of SCK, this IC repeats to output data of the Lock Status byte. In case of Lock Status (LS)
bit “1”, ID Page is locked, Write ID Page command can’t be executed. In case of LS bit “0”, ID Page is released to lock,
Write ID Page command can be executed.
CSB
~~
~~
~~
~~
31
0
1
2
3
4
5
6
7
8
9
10
11
23
24
30
SCK
SI
Instruction Code(8bit)
Address Input (16bit)
~~
0
1
0
0
0
0
1
1
0
0
0
A12
A1 A0
~~
Data Outputs of first byte (8bit) second byte
~~
D7
D6
D2
D1
D0
~~
High-Z
SO
X
~~
X
X
X
X
LS
X =D on’t Care
Figure 47. Read Lock Status Command
(10) Lock ID Page Command (LID)
By Lock ID Page command, data of Lock Status can be written. In case of Lock Status (LS) bit “1”, Lock ID Page
command can’t be executed permanently. As for this command, set CSB to Low, then input address and data after
Instruction Code of Lock ID Page command. Input address bit A10 as “1”, other address bits A12 to A0 as “0”. The
data D1 is for LS bit, other data bits are Don’t Care. Then, by making CSB to High, the IC starts write operation. To
start write operation, set CSB Low to High after taking the last data (D0), and before the next SCK clock starts. At
other timing, Lock ID Page command is not executed, and this Lock ID Page command is cancelled. The write time of
EEPROM requires time of tE/W (Max 4ms).
During write operation, other than Read Status Register command is not accepted.
CSB rising valid timing to start write operation
CSB
~~
0
1
2
3
4
5
6
7
8
9
10
11
23
24
30
31
D0
32
SCK
~~
Instruction Code (8bit)
Data Input (8bit)
Address Input (16bit)
~~
~~
~~
D7
D6
D2
D1
LS
1
0
0
0
0
0
1
0
0
0
0
A12
A1
A0
X
X
X
X
~~
X
SI
High-Z
~~
SO
X=Don’t Care
Figure 48. Lock ID Page Command
At Standby State
1. Standby Current
Set CSB = High, and be sure to set SCK, SI, WPB and HOLDB inputs = Low or High. Do not input intermediate electric
potential.
2. Timing
As shown in Figure.49, at standby, when SCK is High, even if CSB is fallen, SI status is not read at fall edge. SI status is
read at SCK rise edge after fall of CSB. At standby and at power ON/OFF, set CSB = High status.
Even if CSB is fallen at SCK=SI=”H”,
SI status is not read at that edge.
CSB
Command start here. SI is read.
SCK
SI
0
1
2
Figure 49. Operating Timing
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
23/36
Daattaasshheeeett
BR25H640-2AC
Method to cancel each command
1. READ, RDID, RDLS
Instruction Code
8bits
Address
16bits
Data
8bits
・Method to cancel : cancel by CSB = High
Cancel available in all areas of read modes
Figure 50. READ, RDID, RDLS Cancel Valid Timing
2. RDSR
Data
Instruction Code
8 bits
・Method to cancel : cancel by CSB = High
8 bits
Cancel available
in all areas of RDSR
Figure 51. RDSR Cancel Valid Timing
3. WRITE, WRID, LID
Instruction Code
8 bits
Address
16 bits
a:Instruction Code, Address Input Area
Cancellation is available by CSB = High.
b:Data Input Area (D7 to D1 input area)
Cancellation is available by CSB = High.
c:Data Input Area (D0 area)
Data
tE/W
8 bits
b
a
d
c
When CSB is started, write starts.
After CSB rise, cancellation cannot be made by any means.
d:tE/W Area
SCK
SI
D7 D6 D5 D4 D3 D2 D1 D0
Cancellation is available by CSB = High. However, when
write starts (CSB is started) in the area c, cancellation
cannot be made by any means.
c
b
Figure 52. WRITE, WRID, LID Cancel Valid Timing
And by inputting on SCK clock, cancellation cannot be made.
In page write mode, there is write enable area at every 8 clocks
Note 1) If VCC is made OFF during write execution, designated address data is not guaranteed,
therefore write it once again.
Note 2) If CSB is started at the same timing as that of the SCK rise, write execution / cancel becomes unstable,
therefore, it is recommended to fall in SCK = Low area. As for SCK rise, assure timing of tCSS / tCSH or higher.
4. WRSR
a:From Instruction code to 15th rising of SCK
14 15
16
17
SCK
SI
Cancel by CSB = High.
b:From 15th rising of SCK to 16th rising of SCK (write enable area)
When CSB is started, write starts.
D1
D0
a
b
c
c:After 16th rising of SCK
tE/W
Instruction Code
8 bits
Data
Cancel by CSB = High.
However, when write starts (CSB is started) in the area b,
cancellation cannot be made by any means.
And, by inputting on SCK clock, cancellation cannot be made.
8 bits
a
c
b
Figure 53. WRSR Cancel Valid Timing
Note 1) If VCC is made OFF during write execution, designated address data is not guaranteed,
therefore write it once again.
Note 2) If CSB is started at the same timing as that of the SCK rise, write execution / cancel becomes unstable,
therefore, it is recommended to fall in SCK = Low area. As for SCK rise, assure timing of tCSS / tCSH or higher.
5. WREN/WRDI
a:From instruction code to 7th rising of SCK
6
7
8
SCK
Cancel by CSB = High.
b:Cancellation is not available when CSB is started
after 7th clock.
Instruction Code
8 bits
a
b
Figure 54. WREN/WRDI Cancel Valid Timing
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
24/36
Daattaasshheeeett
BR25H640-2AC
High speed operation
In order to realize stable high speed operations, pay attention to the following input / output pin conditions.
1. Pull Up, Pull Down Resistance for Input Pins
When to attach pull up, pull down resistance to EEPROM input pins, select an appropriate value for the microcontroller
VOL, IOL from VIL characteristics of this IC.
2. Pull Up Resistance
VCC -VOLM
RPU
・・・①
IOLM
Microcontroller
VOLM
Low Output
IOLM
EEPROM
VILE
・・・②
RPU
VOLM VILE
Example) When Vcc=5V, VILE=1.5V, VOLM=0.4V, IOLM=2mA,
from the equation ①,
Low Input
5 -0.4
・VILE : VIL specifications of EEPROM
・VOLM : VOL specifications of Microcontroller
・IOLM : IOL specifications of Microcontroller
RPU
-3
210
∴RPU 2.3 ꢁ kΩ ꢀ
With the value of RPU to satisfy the above equation, VOLM
becomes 0.4V or lower, and with VILE (=1.5V), the equation ② is
also satisfied.
Figure 55. Pull Up Resistance
And, in order to prevent malfunction, mistake write at power ON/OFF, be sure to make CSB pull up.
3. Pull Down Resistance
VOHM
RPD
Microcontroller
VOHM
EEPROM
VIHE
・・・③
・・・④
IOHM
VOHM VIHE
High Output
RPD
High Input
IOHM
Example) When VCC=5V, VOHM=VCC-0.5V, IOHM=0.4mA,
VIHE=VCC×0.7V, from the equation ③,
・VIHE : VIH specifications of EEPROM
・VOHM : VOH specifications of Microcontroller
・IOHM : IOH specifications of Microcontroller
5 - 0.5
RPD
-3
0.4 10
RPU 11.3 ꢁ kΩ ꢀ
Figure 56. Pull Down Resistance
Further, by amplitude VIHE, VILE of signal input to EEPROM, operation speed changes. By inputting signal of amplitude of Vcc
/ GND level to input, more stable high speed operations can be realized. On the contrary, when amplitude of 0.8Vcc / 0.2Vcc
is input, operation speed becomes slow.(Note1)
In order to realize more stable high speed operation, it is recommended to make the values of RPU, RPD as large as possible,
and make the amplitude of signal input to EEPROM close to the amplitude of Vcc / GND level.
(Note1) At this moment, operating timing guaranteed value is guaranteed.
tPD - VIL Characteristic
80
70
Spec
60
50
40
30
Vcc=2.5V
20
Ta=25
°C
VIH=Vcc
10
0
CL=100pF
0
0.2
0.4
0.6
0.8
1
VIL[V]
Figure 57. VIL dependency of Data Output Delay Time tPD
4. SO Load Capacitance Condition
Load capacitance of SO Pin affects upon delay characteristic of SO output. (Data Output Delay Time, Time from HOLDB to
High-Z) In order to make output delay characteristic into higher speed, make SO load capacitance small. In concrete, “Do not
connect many devices to SO bus”, “Make the wire between the controller and EEPROM short”, and so forth.
5. Other cautions
Make the wire length from the Microcontroller to EEPROM input signal same length, in order to prevent setup / hold violation
to EEPROM, owing to difference of wire length of each input.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
25/36
16.Feb.2016 Rev.002
Daattaasshheeeett
BR25H640-2AC
I/O Equivalence Circuit
1. Output Circuit
SO
OEint.
Figure 58. SO Output Equivalent Circuit
2. Input Circuit
RESETint.
CSB
Figure 59. CSB Input Equivalent Circuit
SI
SCK
Figure 61. SI Input Equivalent Circuit
Figure 60. SCK Input Equivalent Circuit
WPB
HOLDB
Figure 62. HOLDB Input Equivalent Circuit
Figure 63. WPB Input Equivalent Circuit
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
26/36
Daattaasshheeeett
BR25H640-2AC
Power-Up/Down conditions
1. At power ON/OFF, set CSB = High (=Vcc).
When CSB is Low, this IC gets in input accept status (active). If power is turned on in this status, noises and the likes may
cause malfunction, mistake write or so. To prevent these, at power ON, set CSB = High. (When CSB is in High status, all
inputs are canceled.)
Vcc
Vcc
GND
Vcc
CSB
GND
Good
Bad
Example
Example
Figure 64. CSB Timing at power ON / OFF
(Good example) CSB Pin is pulled up to Vcc.
At power OFF, take 10ms or higher before supply. If power is turned on without observing this condition, the IC
internal circuit may not be reset, which please note.
(Bad example)
CSB Pin is Low at power ON/OFF.
In this case, CSB always becomes Low (active status), and EEPROM may have malfunction, mistake write
owing to noises and the likes.
Even when CSB input is High-Z, the status becomes like this case, which please note.
2. POR Circuit
This IC has a POR (Power On Reset) circuit as mistake write countermeasure. After POR , it gets in write disable status.
The POR circuit is valid only when power is ON, and does not work when power is OFF. When power is ON, if the
recommended conditions of the following tR, tOFF, and Vbot are not satisfied, it may become write enable status owing to
noises and the likes.
Table 11. Recommended conditions of tR, tOFF, Vbot
tR
Vcc
0
tR
tOFF
Vbot
10ms or below
100ms or below
10ms or higher
10ms or higher
0.3V or below
0.2V or below
tOFF
Vbot
Figure 65. Rise Waveform
3. LVCC Circuit
LVCC (VCC-Lockout) circuit prevents data rewrite operation at low supply voltage, and prevents wrong write.
At LVCC voltage (Typ. =1.9V) or below, it prevent data rewrite.
Noise countermeasures
1. Vcc Noise (bypass capacitor)
When noise or surge gets in the power source line, malfunction may occur, therefore, for removing these, it is
recommended to attach a bypass capacitor (over 0.1μF) between IC Vcc and GND. At that moment, attach it as close to
IC as possible. And, it is also recommended to attach a bypass capacitor between board Vcc and GND.
2. SCK Noise
When the rise time (tRC) of SCK is long, and a certain degree or more of noise exists, malfunction may occur owing to
clock bit displacement. To avoid this, a Schmitt trigger circuit is built in SCK input. The hysteresis width of this circuit is set
about 0.2V, if noises exist at SCK input, set the noise amplitude 0.2Vp-p or below. And it is recommended to set the rise
time (tRC) of SCK 100ns or below. In the case when the rise time is 100ns or higher, take sufficient noise countermeasures.
Make the clock rise, fall time as small as possible.
3. WPB Noise
During execution of Write Status Register command, if there exist noises on WPB pin, mistake in recognition may occur
and forcible cancellation may result, which please note. To avoid this, a Schmitt trigger circuit is built in WPB input. In the
same manner, a Schmitt trigger circuit is built in CSB input, SI input and HOLDB input too.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
27/36
16.Feb.2016 Rev.002
Daattaasshheeeett
BR25H640-2AC
Operational Notes
1.
2.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating,
increase the board size and copper area to prevent exceeding the Pd rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
28/36
Daattaasshheeeett
BR25H640-2AC
Operational Notes – continued
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
12. Regarding the Input Pin of the IC
In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation
of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage.
Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin
lower than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when no power
supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have
voltages within the values specified in the electrical characteristics of this IC.
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
29/36
Daattaasshheeeett
BR25H640-2AC
Part Numbering
B
R
2
5
H
6
4
0
x
x
x
-
2
A
C
x
x
BUS Type
25 : SPI
Operating Temperature / Voltage
: -40oC to +125oC / 2.5V to 5.5V
H
Capacity
640 : 64Kbit
Package
FVM : MSOP8, FVT : TSSOP-B8, F : SOP8, FJ : SOP-J8
2
: Process Code
A
C
: Revision
: For Automotive Application
Packaging and Forming Specification
E2 : Embossed tape and reel
TR : Embossed tape and reel (MSOP8 package only)
Lineup
Package
Capacity
Orderable Part Number
Type
MSOP8
TSSOP-B8
SOP8
Quantity
Reel of 3000
Reel of 3000
Reel of 2500
Reel of 2500
BR25H640FVM -2ACTR
BR25H640FVT -2ACE2
64Kbit
BR25H640F
BR25H640FJ
-2ACE2
-2ACE2
SOP-J8
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
30/36
Daattaasshheeeett
BR25H640-2AC
Physical Dimension, Tape and Reel Information
Package Name
MSOP8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1pin
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
Reel
∗
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
31/36
Daattaasshheeeett
BR25H640-2AC
Physical Dimensions, Tape and Reel Information - continued
Package Name
TSSOP-B8
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
32/36
Daattaasshheeeett
BR25H640-2AC
Physical Dimensions, Tape and Reel Information - continued
Package Name
SOP8
(Max 5.35 (include.BURR)
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
33/36
Daattaasshheeeett
BR25H640-2AC
Physical Dimensions, Tape and Reel Information - continued
Package Name
SOP-J8
<Tape and Reel information>
Tape
Embossed carrier tape
2500pcs
Quantity
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
34/36
Daattaasshheeeett
BR25H640-2AC
Marking Diagrams (TOP VIEW)
MSOP8 (TOP VIEW)
TSSOP-B8 (TOP VIEW)
Part Number Marking
Part Number Marking
LOT Number
H
A
6
4
LOT Number
1PIN MARK
1PIN MARK
SOP8 (TOP VIEW)
SOP-J8 (TOP VIEW)
Part Number Marking
Part Number Marking
H 6 4 0 A
H 6 4 0 A
LOT Number
LOT Number
1PIN MARK
1PIN MARK
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
35/36
Daattaasshheeeett
BR25H640-2AC
Revision History
Date
Revision
001
Changes
01.Oct.2014
16.Feb.2016
New Release
P4 Indicated Limit of tFO
.
002
P19 Modified Sentence in (4) Write Command.
P20 Modified Figure 42..
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0R1R0G100210-1-2
16.Feb.2016 Rev.002
36/36
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Datasheet
Buy
BR25H640F-2AC - Web Page
Distribution Inventory
Part Number
Package
BR25H640F-2AC
SOP8
Unit Quantity
2500
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
2500
Taping
inquiry
Yes
相关型号:
©2020 ICPDF网 联系我们和版权申明