BRCH064GWZ-3 [ROHM]
BRCH064GWZ-3是² BUS接口方式的64kbit串行EEPROM。;
| 型号： | BRCH064GWZ-3 |
| 厂家： | 
ROHM |
| 描述： | BRCH064GWZ-3是² BUS接口方式的64kbit串行EEPROM。 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 |
| 文件： | 总29页 (文件大小：2167K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
Serial EEPROM Series Standard EEPROM
WLCSP EEPROM
BRCH064GWZ-3
General Description
BRCH064GWZ-3 is a 64Kbit serial EEPROM of I2C BUS Interface Method
Packages W(Typ) x D(Typ) x H(Max)
UCSP30L1A 1.50mm x1.00mm x 0.33mm
Features
Completely Conforming to the World Standard I2C
BUS.
All Controls Available by 2 Ports of Serial Clock
(SCL) and serial data (SDA)
Other Devices than EEPROM can be Connected to
the Same Port, Saving Microcontroller Port
1.6V to 5.5V Single Power Source Operation Most
Suitable for Battery Use
1.6V to 5.5V Wide Limit of Operating Voltage,
Possible FAST MODE 400KHz Operation
Up to 32 Byte in Page Write Mode
Bit Format 8K x 8
Self-timed Programming Cycle
Low Current Consumption
Prevention of Write Mistake
Write (Write Protect) Function Added
Prevention of write mistake at low voltage
More than 1 Million Write Cycles
More than 40 Years Data Retention
Noise Filter Built in SCL / SDA Terminal
Initial Delivery State FFh
○Product structure：Silicon monolithic integrated circuit ○This product has no designed protection against radioactive rays
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
1/26
TSZ22111･14･001
Datasheet
BRCH064GWZ-3
Absolute Maximum Ratings (Ta=25°C)
Parameter
Supply Voltage
Symbol
VCC
Rating
-0.3 to +6.5
Unit
V
Remark
Power Dissipation
Pd
0.22(UCSP30L1A)
-65 to +125
W
Derate by 2.2mW/°C when operating above Ta=25°C
Storage Temperature
Operating Temperature
Tstg
Topr
°C
°C
-40 to +85
The Max value of Input Voltage/Output Voltage is not over 6.5V.
When the pulse width is 50ns or less, the Min value of Input
Voltage/Output Voltage is not below 1.0V.
Input Voltage/
Output Voltage
-
-0.3 to Vcc+1.0
150
V
Junction Temperature
Tjmax
°C
Junction temperature at the storage condition
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Memory Cell Characteristics (Ta=25°C, Vcc=1.6V to 5.5V)
Limit
Parameter
Unit
Min
1,000,000
40
Typ
Max
Write Cycles (Note1)
-
-
-
-
Times
Years
Data Retention (Note1)
(Note1) Not 100% TESTED
Recommended Operating Ratings
Parameter
Power Source Voltage
Input Voltage
Symbol
Rating
1.6 to 5.5
0 to Vcc
Unit
V
Vcc
VIN
DC Characteristics
(
Unless otherwise specified, Ta=-40°C to +85°C
,
Vcc=1.6V to 5.5V
)
Limit
Parameter
Symbol
Unit
Conditions
Min
Typ
Max
Vcc+1.0
+0.3Vcc
Vcc+1.0
+0.2Vcc
0.4
Input High Voltage1
Input Low Voltage1
Input High Voltage2
Input Low Voltage2
Output Low Voltage1
Output Low Voltage2
Input Leakage Current
Output Leakage Current
VIH1
VIL1
VIH2
VIL2
VOL1
VOL2
ILI
0.7Vcc
-0.3 (Note2)
-
-
-
-
-
-
-
-
V
V
1.7V≤Vcc≤5.5V
1.7V≤Vcc≤5.5V
1.6V≤Vcc＜1.7V
1.6V≤Vcc＜1.7V
0.8Vcc
-0.3 (Note2)
V
V
-
V
IOL=3.0mA, 2.5V≤Vcc≤5.5V (SDA)
IOL=0.7mA, 1.6V≤Vcc＜2.5V (SDA)
VIN=0 to Vcc
-
0.2
V
-1
-1
+1
µA
µA
ILO
+1
VOUT=0 to Vcc (SDA)
Vcc=5.5V, fSCL=400kHz, tWR=5ms,
Byte Write, Page Write
Supply Current (Write)
ICC1
-
-
2.0
mA
Vcc=5.5V, fSCL=400kHz
Random Read, current Read, Sequential
Read
WP=GND or Vcc
Vcc=5.5V, SDA・SCL=Vcc
WP=GND or Vcc, TEST=GND or Vcc
Supply Current (Read)
Standby Current
ICC2
-
-
-
-
0.5
2.0
mA
µA
ISB
(Note2) When the pulse width is 50ns or less, it is -1.0V.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
2/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
AC Characteristics (Unless otherwise specified, Ta=-40°C to +85°C, Vcc=1.6V to 5.5V)
Limit
Parameter
Symbol
Unit
Min
-
Typ
Max
Clock Frequency
fSCL
tHIGH
tLOW
tR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
400
kHz
μs
µs
µs
µs
µs
µs
µs
ns
ns
µs
µs
µs
µs
ms
µs
µs
µs
µs
Data Clock High Period
0.6
1.2
-
-
Data Clock Low Period
-
SDA,SCL(INPUT) Rise Time (Note1)
SDA,SCL (INPUT)Fall Time (Note1)
1.0
tF1
-
1.0
SDA(OUTPUT)Fall Time (Note1)
Start Condition Hold Time
Start Condition Setup Time
Input Data Hold Time
Input Data Setup Time
Output Data Delay Time
Output Data Hold Time
Stop Condition Setup Time
Bus Free Time
tF2
-
0.3
tHD:STA
tSU:STA
tHD:DAT
tSU:DAT
tPD
0.6
0.6
0
-
-
-
100
0.1
0.1
0.6
1.2
-
-
0.9
tDH
-
-
tSU:STO
tBUF
-
Write Cycle Time
tWR
5
0.1
-
Noise Spike Width (SDA and SCL)
WP Hold Time
tI
-
tHD:WP
tSU:WP
tHIGH:WP
1.0
0.1
1.0
WP Setup Time
-
WP High Period
-
(Note1) Not 100% TESTED.
Condition Input Data Level: VIL=0.2×Vcc VIH=0.8×Vcc
Input Data Timing Reference Level: 0.3×Vcc/0.7×Vcc
Output Data Timing Reference Level: 0.3×Vcc/0.7×Vcc
Rise/Fall Time : ≤20ns
Serial Input / Output Timing
tR
tF1
tHIGH
70%
70%
30%
70%
SCL
70% 70%
30%
70%
30%
30%
tLOW
tHD:STA
DATA(n)
tHD:DAT
DATA(1)
D0 ACK
tSU:DAT
70%
ACK
D1
70%
70%
70%
70%
30%
tWR
30%
SDA
(INPUT)
tDH
tPD
tBUF
30%
30%
70%
70%
30%
SDA
(OUTPUT)
30%
30%
tSU:WP
tHD:WP
STOP CONDITION
Input read at the rise edge of SCL
○Data output in sync with the fall of SCL
tF2
Figure 1.-(a). Serial Input / Output Timing
Figure 1.-(d). WP Timing at Write Execution
70%
DATA(n)
DATA(1)
D0
70%
70%
70%
D1
ACK
ACK
tSU:STA
tHD:STA
tSU:STO
tWR
tHIGH:WP
70%
70%
70%
30%
30%
STOP CONDITION
START CONDITION
Figure 1.-(b) Start-Stop Bit Timing
Figure 1.-(e). WP Timing at Write Cancel
70%
70%
ACK
D0
write data
(n-th address)
tWR
STOP CONDITION START CONDITION
Figure 1.-(c). Write Cycle Timing
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
3/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Block Diagram
64Kbit EEPROM ARRAY
SLAVE, WORD
Vcc
13bit
8bit
ADDRESS
DECODER
DATA
REGISTER
WP
13bit
ADDRESS REGISTER
START
STOP
SCL
TEST
CONTROL LOGIC
ACK
SDA
GND
HIGH VOLTAGE GEN.
VCC LEVEL DETECT
Figure 2. Block Diagram
Pin Configuration
2
3
1
B3
B1
SDA
A1
B2
GND
A2
B
A
TEST
A3
SCL
WP
VCC
Figure 3. Pin Configuration
(BOTTOM VIEW)
Pin Descriptions
Land No. Terminal Name Input / Output
Descriptions
B3
B2
TEST
GND
Input
-
Slave address setting
Reference voltage of all input / output, 0V
Slave and word address
Serial data input, serial data output
B1
SDA
Input / Output
A3
A2
A1
VCC
WP
-
Power Supply
Input
Input
Write protect terminal
Serial clock input
SCL
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
4/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Typical Performance Curves
6
6
5
4
3
2
1
0
Ta=-40°C
Ta= 25°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
5
Ta= 85°C
4
3
SPEC
2
1
0
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(v)
SupplyVoltage: Vcc(v)
Figure 5. Input Low Voltage1,2
vs Supply Voltage
Figure 4. Input High Voltage1,2,
vs Supply Voltage
1
0.8
0.6
0.4
0.2
0
1
Ta=-40°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.8
0.6
0.4
0.2
0
Ta= 25°C
Ta= 85°C
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
Output Low Current: IOL(mA)
Output Low Current: IOL(mA)
Figure 6. Output Low Voltage1
vs Output Low Current
(Vcc=2.5V)
Figure 7. Output Low Voltage2
vs Output Low Current
(Vcc=1.6V)
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
5/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
1.2
1.2
1
SPEC
SPEC
1
Ta=-40°C
Ta= 25°C
Ta=-40℃
Ta= 25℃
Ta= 85℃
0.8
0.8
0.6
0.4
0.2
0
Ta= 85°C
0.6
0.4
0.2
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(v)
Figure 8. Input Leakage Current vs Supply Voltage
(SCL, WP, TEST)
Figure 9. Output Leakage Current vs Supply Voltage
(SDA)
0.6
0.5
0.4
0.3
0.2
0.1
0
3
2.5
2
SPEC
SPEC
Ta=-40°C
Ta= 25°C
Ta= 85°C
1.5
1
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.5
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 11. Supply Current (Read) vs Supply Voltage
(fSCL=400kHz)
Figure 10. Supply Current (Write) vs Supply Voltage
(fSCL=400kHz)
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
6/26
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
2.5
10000
1000
100
10
SPEC
2
SPEC
1.5
Ta=-40°C
Ta= 25°C
Ta= 85°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
1
0.5
0
1
0.1
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 13. Clock Frequency vs Supply Voltage
Figure 12. Standby Current vs Supply Voltage
1
0.8
0.6
0.4
0.2
0
1.5
1.2
0.9
0.6
0.3
0
SPEC
SPEC
Ta=-40°C
Ta= 25°C
Ta= 85°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 15. Data Clock Low Period vs Supply Voltage
Figure 14. Data Clock High Period vs Supply Voltage
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
7/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
1
1
0.8
0.6
0.4
0.2
0
0.8
SPEC
SPEC
0.6
Ta=-40°C
Ta= 25°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.4
0.2
0
Ta= 85°C
-0.2
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
Figure 16. Start Condition Hold Time vs Supply Voltage
SupplyVoltage: Vcc(V)
Figure 17. Start Condition Setup Time vs Supply Voltage
50
50
SPEC
SPEC
0
-50
0
-50
Ta=-40°C
Ta= 25°C
Ta= 85°C
Ta=-40°C
Ta= 25°C
-100
-150
-200
-100
Ta= 85°C
-150
-200
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 19. Input Data Hold Time vs Supply Voltage
(LOW)
Figure 18. Input Data Hold Time vs Supply Voltage
(HIGH)
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
8/26
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
300
200
100
0
300
200
SPEC
SPEC
100
0
Ta=-40°C
Ta= 25°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
-100
-200
Ta= 85°C
-100
-200
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 20. Input Data Setup Time vs Supply Voltage
(HIGH)
Figure 21. Input Data Setup Time vs Supply Voltage
(LOW)
2
2
Ta=-40°C
Ta= 25°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
1.5
1.5
Ta= 85°C
1
SPEC
1
SPEC
0.5
0.5
SPEC
SPEC
0
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 22. Output Data Delay Time
vs Supply Voltage
Figure 23. Output Data Delay Time
vs Supply Voltage
(LOW)
(HIGH)
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
9/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
2
1.5
1
2
1.5
Ta=-40°C
Ta= 25°C
Ta= 85°C
SPEC
1
SPEC
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.5
0.5
0
0
-0.5
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 25. Bus Free Time vs Supply Voltage
Figure 24. Stop Condition Setup Time
vs Supply Voltage
6
5
4
3
2
1
0
0.6
0.5
0.4
0.3
0.2
0.1
0
SPEC
Ta=-40°C
Ta= 25°C
Ta= 85°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 26. Write Cycle Time vs Supply Voltage
Figure 27. Noise Spike Width
vs Supply Voltage
(SCL HIGH)
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
10/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
0.6
0.5
0.6
0.5
0.4
0.3
0.2
0.1
0
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.4
0.3
0.2
0.1
0
Ta=-40°C
Ta= 25°C
Ta= 85°C
SPEC
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 29. Noise Spike Width
vs Supply Voltage
Figure 28. Noise Spike Width
vs Supply Voltage
(SCL LOW)
(SDA HIGH)
0.6
1.2
1
SPEC
0.5
0.4
0.3
0.2
0.1
0
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.8
0.6
0.4
0.2
0
Ta=-40°C
Ta= 25°C
Ta= 85°C
SPEC
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 30. SDA Noise Spike Width (LOW)
vs Supply Voltage
Figure 31. WP Hold Time vs Supply Voltage
(SDA LOW)
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
11/26
Datasheet
BRCH064GWZ-3
Typical Performance Curves‐continued
0.2
1.2
1
SPEC
SPEC
0.1
0
Ta=-40°C
Ta= 25°C
Ta=-40°C
Ta= 25°C
Ta= 85°C
0.8
0.6
0.4
0.2
0
-0.1
Ta= 85°C
-0.2
-0.3
-0.4
-0.5
-0.6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
SupplyVoltage: Vcc(V)
SupplyVoltage: Vcc(V)
Figure 33. WP High Period vs Supply Voltage
Figure 32. WP Setup Time vs Supply Voltage
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
12/26
Datasheet
BRCH064GWZ-3
Timing Chart
1. I2C BUS Data Communication
I2C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long,
and acknowledge is always required after each byte. I2C BUS data communication with several devices is possible by
connecting with 2 communication lines: serial data (SDA) and serial clock (SCL).
Among the devices, there should be a “master” that generates clock and control communication start and end. The rest
become “slave” which are controlled by an address peculiar to each device, like this EEPROM. The device that outputs
data to the bus during data communication is called “transmitter”, and the device that receives data is called “receiver”.
SDA
1-7
1-7
1-7
8
9
8
9
8
9
SCL
S
P
START ADDRESS R/W
condition
ACK
DATA
ACK
DATA
ACK
STOP
condition
Figure 34. Data Transfer Timing
2. Start Condition (Start Bit Recognition)
(1) Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL
is 'HIGH' is necessary.
(2) This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this condition
is satisfied, any command cannot be executed.
3. Stop Condition (Stop Bit Recognition)
(1) Each command can be ended by a stop condition (stop bit) where SDA goes from 'LOW' to 'HIGH' while SCL is
'HIGH'.
4. Acknowledge (ACK) Signal
(1) The acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In
a master-slave communication, the device (Ex. µ-COM sends slave address input for write or read command, to
this IC ) at the transmitter (sending) side releases the bus after output of 8bit data.
(2) The device (Ex. This IC receives the slave address input for write or read command from the µ-COM) at the
receiver (receiving) side sets SDA 'LOW' during the 9th clock cycle, and outputs acknowledge signal (ACK signal)
showing that it has received the 8bit data.
(3) This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'.
(4) After receiving 8bit data (word address and write data) during each write operation, this IC outputs acknowledge
signal (ACK signal) 'LOW'..
(5) During read operation, this IC outputs 8bit data (read data) and detects acknowledge signal (ACK signal) 'LOW'.
When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (µ-COM) side,
this IC continues to output data. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer,
recognizes stop condition (stop bit), and ends read operation. Then this IC becomes ready for another
transmission.
5. Device Addressing
(1) Slave address comes after start condition from master.
(2) The significant 4 bits of slave address are used for recognizing a device type.
The device code of this IC is fixed to '1010'.
(3) Next slave addresses (A2 0 0 --- device address) are for selecting devices, and plural ones can be used on a
same bus according to the number of device addresses.
(4) The most insignificant bit (R / W --- READ / WRITE ) of slave address is used for designating write or read
operation, and is as shown below.
Setting R/ W to 0 ------- write (setting 0 to word address setting of random read)
Setting R/ W to 1 ------- read
Maximum number of
Slave address
Connected buses
1
0
1
0
A2
0
0
R/―W―
2
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
13/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Write Command
1. Write Cycle
(1) Arbitrary data can be written to this EEPROM. When writing only 1 byte, Byte Write is normally used, and when
writing continuous data of 2 bytes or more, simultaneous write is possible by Page Write cycle. Up to 32 arbitrary
bytes can be written.
S
T
A
R
T
W
R
I
T
E
S
T
O
SLAVE
ADDRESS
1st WORD
ADDRESS
2nd WORD
ADDRESS
DATA
P
SDA
LINE
WAWA
*
12 11
WA
0
1
0
1
0 A2 0
0
D7
D0
*Don't Care bit
*
*
A
C
K
A
C
K
A
C
K
R
/
W
A
C
K
Figure 35. Byte Write Cycle
S
T
A
R
T
W
R
I
T
E
S
T
O
P
SLAVE
ADDRESS
1st WORD
ADDRESS(n)
2nd WORD
ADDRESS(n)
DATA(n)
DATA(n+31)
SDA
LINE
WA WA
12 11
WA
0
0
A2
0 0
1
1
D7
D0
D0
0
*Don't Care bit
A
R
/
W
A
C
K
A
C
K
A
C
K
A
C
K
C
K
Figure 36. Page Write Cycle
(2) During internal write execution, all input commands are ignored, therefore ACK is not returned.
(3) Data is written to the address designated by word address (n-th address)
(4) By issuing stop bit after 8bit data input, internal write to memory cell starts.
(5) When internal write is started, command is not accepted for tWR (5ms at maximum).
(6) Using page write cycle, writing in bulk is done as follows: When data of more than 32 bytes is sent, the bytes in
excess overwrites the data already sent first.
(Refer to "Internal Address Increment".)
(7) As for page write cycle where 2 or more bytes of data is intended to be written, after the 8 significant bits of word
address are designated arbitrarily, only the value of 5 least significant bits in the address is incremented internally,
so that data up to 32 addresses of memory only can be written.
1 page=32bytes, but the page Write Cycle Time is 5ms at maximum for 32byte bulk write.
It does not stand 5ms at maximum × 32byte=160ms(Max)
2. Internal Address Increment
Page Write Mode
WA7 WA6 WA5 WA4 WA3 WA2 WA1 WA0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
Increment
For example, when it is started from address 1Eh,
then, increment is made as below,
1Eh→1Fh→00h→01h･･･ please take note.
0
0
0
0
0
0
0
0
0
1
1
0
1
1
0
1
1
0
1
1
0
0
1
0
1Eh
※1Eh･･･1E in hexadecimal, therefore,
00011110 becomes a binary number.
Significant bit is fixed.
No digit up
3. Write Protect (WP) Terminal
Write Protect (WP) Function
When WP terminal is set at Vcc (H level), data rewrite of all addresses is prohibited. When it is set at GND (L level), data
rewrite of all address is enabled. Be sure to connect this terminal to Vcc or GND, or control it to H level or L level. Do not
leave it open.
At extremely low voltage at power ON / OFF, by setting the WP terminal 'H', write error can be prevented.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
14/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Read Command
1. Read Cycle
Read cycle is when data of EEPROM is read. Read cycle could be random read cycle or current read cycle. Random
read cycle is a command to read data by designating a specific address, and is used generally. Current read cycle is a
command to read data of internal address register without designating an address, and is used when to verify just after
write cycle. In both the read cycles, sequential read cycle is available where the next address data can be read in
succession.
S
T
A
R
T
W
R
I
T
E
S
T
A
R
T
R
E
A
D
S
T
O
P
SLAVE
ADDRESS
1st WORD
ADDRESS
2nd WORD
ADDRESS(n)
SLAVE
ADDRESS
DATA(n)
SDA
LINE
WA
WAWA
D7
D0
1
0
1
0
A2
0
A2
0 0
0
1 0
1
0
0
12 11
* *
*Don't Care bit
*
R A
A
C
K
A
C
K
R
A
C
A
C
K
/
C
/
W K
W K
Figure 37. Random Read Cycle
S
T
A
R
T
R
E
A
D
S
T
O
SLAVE
ADDRESS
DATA(n)
P
SDA
LINE
A2
1 0 1 0
0 0
D7
D0
A
C
K
R A
/
C
W K
Figure 38. Current Read Cycle
S
R
E
A
D
S
T
O
P
T
A
R
T
SLAVE
ADDRESS
DATA(n)
DATA(n+x)
SDA
LINE
A2
0
0
1
0
1
0
D7
D0
D7
D0
R
/
A
C
A
C
K
A
C
K
A
C
K
W K
Figure 39. Sequential Read Cycle (in the case of Current Read Cycle)
(1) In Random Read Cycle, data of designated word address can be read.
(2) When the command just before current read cycle is random read cycle, current read cycle (each including sequential
read cycle), data of incremented last read address (n)-th, i.e., data of the (n+1)-th address, is output.
(3) When ACK signal 'LOW' after D0 is detected, and stop condition is not sent from master (µ-COM) side, the next
address data can be read in succession.
(4) Read cycle is ended by stop condition where 'H' is input to ACK signal after D0 and SDA signal goes from ‘L’ to ‘H’
while SCL signal is 'H' .
(5) When 'H' is not input to ACK signal after D0, sequential read gets in, and the next data is output.
Therefore, read command cycle cannot be ended. To end the read command cycle, be sure to input 'H' to ACK signal
after D0, and the stop condition where SDA goes from ‘L’ to ‘H’ while SCL signal is 'H'.
(6) Sequential read is ended by stop condition where 'H' is input to ACK signal after arbitrary D0 and SDA is asserted from
‘L’ to ‘H’ while SCL signal is 'H'.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
15/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Software Reset
Software reset is executed to avoid malfunction after power on and during command input. Software reset has several
kinds and 3 kinds of them are shown in the figure below. (Refer to Figure 40.-(a), Figure 40.-(b), and Figure 40.-(c).) Within
the dummy clock input area, the SDA bus is released ('H' by pull up) and ACK output and read data '0' (both 'L' level) may
be output from EEPROM. Therefore, if 'H' is input forcibly, output may conflict and over current may flow, leading to
instantaneous power failure of system power source or influence upon devices.
Dummy clock×14
Start×2
SCL
SDA
Normal command
Normal command
1
2
13
14
Figure 40.-(a) The case of dummy clock×14 + START+START+ command input
Start
Dummy clock×9
Start
SCL
SDA
Normal command
Normal command
1
2
8
9
Figure 40.-(b) The case of START + dummy clock×9 + START + command input
Start×9
SCL
Normal command
Normal command
1
2
3
7
8
9
SDA
Figure 40.-(c) START×9 + command input
※Start command from START input.
Acknowledge Polling
During internal write execution, all input commands are ignored, therefore ACK is not returned. During internal automatic
write execution after write cycle input, next command (slave address) is sent.If the first ACK signal sends back 'L', then it
means end of write operation, else 'H' is returned, which means writing is still in progress. By the use of acknowledge
polling, next command can be executed without waiting for tWR = 5ms.
To write continuously, R/ W = 0, then to carry out current read cycle after write, slave address with R/ W = 1 is sent. If
ACK signal sends back 'L', then execute word address input and data output and so forth.
During internal write,
ACK = HIGH is returned.
First write command
S
T
A
R
T
S
T
A
R
T
S
S
T
A
C
K
H
A
T
A
R
T
Slave
Slave
C
K
H
Write Command
O
…
Address
Address
P
tWR
Second write command
S
T
A
R
T
S
S
T
O
P
A
C
K
L
A
C
K
L
A
C
K
H
A
C
K
L
Slave
Word
T
A
R
T
Slave
…
Data
Address
Address
Address
tWR
After completion of internal write,
ACK=LOW is returned, so input next
word address and data in succession.
Figure 41. Case of continuous write by Acknowledge Polling
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
16/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
WP Valid Timing (Write Cancel)
WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so on, pay attention to the following WP valid
timing. During write cycle execution, inside cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte
write cycle and page write cycle, the area from the first start condition of command to the rise of clock to take in D0 of
data(in page write cycle, the first byte data) is the cancel invalid area.
WP input in this area becomes ‘Don't care’. The area from the rise of SCL to take in D0 to the stop condition input is the
cancel valid area. Furthermore, after the execution of forced end by WP, the IC enters standby status.
・Rise of D0 taken clock
・Rise of SDA
SCL
SCL
SDA
D1
D0 ACK
SDA D0
ACK
Enlarged view
Enlarged view
S
A
A
C
K
L
A
C
K
L
A
C
K
L
S
T
O
P
tWR
T
A
R
T
Slave
Word
SDA
WP
D6
D2
D3 D1 D0
C
K
L
D7
D5
D4
Data
Address
Address
WP cancel invalid area
WP cancel valid area
Data is not written.
WP cancel invalid area
Figure 42. WP Valid Timing
Command Cancel by Start Condition and Stop Condition
During command input, by continuously inputting start condition and stop condition, command can be cancelled. (Figure
43.) However, within ACK output area and during data read, SDA bus may output 'L'. In this case, start condition and stop
condition cannot be input, so reset is not available. Therefore, execute software reset. When command is cancelled by
start-stop condition during random read cycle, sequential read cycle, or current read cycle, internal setting address is not
determined. Therefore, it is not possible to carry out current read cycle in succession. To carry out read cycle in succession,
carry out random read cycle.
SCL
SDA
1
0
1
0
Start condition
Stop condition
Figure 43. Case of cancel by start, stop condition during Slave Address Input
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
17/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
I/O Peripheral Circuit
1. Pull Up Resistance of SDA Terminal
SDA is NMOS open drain, so it requires a pull up resistor. As for this resistance value (RPU), select an appropriate value
from microcontroller VIL, IL, and VOL-IOL characteristics of this IC. If RPU is large, operating frequency is limited. The smaller
the RPU, the larger is the supply current (Read).
2. Maximum Value of RPU
The maximum value of RPU is determined by the following factors:
(1)SDA rise time to be determined by the capacitance (CBUS) of bus line and RPU of SDA should be tR or lower.
Furthermore, AC timing should be satisfied even when SDA rise time is slow.
(2)The bus’ electric potential
A to be determined by the input current leak total (IL) of the device connected to the bus
○
with output of 'H' to the SDA line and RPU should sufficiently secure the input 'H' level (VIH) of microcontroller and
EEPROM including recommended noise margin of 0.2Vcc.
V
CC -I
L
R
PU -0.2VCC VIH
Microcontroller
EEPROM
0.8VCC -VIH
∴RPU
RPU
IL
SDA terminal
A
Ex.) Vcc =3V IL=10µA VIH=0.7 Vcc
from(2)
IL
IL
0.83-0.73
Bus Line
Capacity
CBUS
∴RPU
1010 -6
30[k]
Figure 44. I/O Circuit Diagram
3. Minimum Value of RPU
The minimum value of RPU is determined by the following factors:
(1)When IC outputs LOW, it should be satisfied that VOLMAX=0.4V and IOLMAX=3mA.
V
CC -VOL
IOL
RPU
V
CC -VOL
∴ RPU
IOL
(2)VOLMAX=0.4V should secure the input 'L' level (VIL) of microcontroller and EEPROM
including the recommended noise margin of 0.1Vcc.
VOLMAX VIL -0.1VCC
Ex.) VCC =3V, VOL=0.4V, IOL=3mA, microcontroller, EEPROM VIL=0.3Vcc
from (1)
3-0.4
∴RPU
-3
310
867 []
And
VOL =0.4 [V ]
VIL =0.3 ×3
=0.9 [V ]
Therefore, the condition (2) is satisfied.
4. Pull-up Resistance of SCL Terminal
When SCL control is made at the CMOS output port, there is no need for a pull up resistor. But when there is a time
where SCL becomes 'Hi-Z', add a pull up resistor. As for the pull up resistor value, one of several kΩ to several ten kΩ is
recommended in consideration of drive performance of output port of microcontroller.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
18/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Cautions on Microcontroller Connection
1. RS
In I2C BUS, it is recommended that SDA port is of open drain input/output. However, when using CMOS input / output of
tri state to SDA port, insert a series resistance RS between the pull up resistor RPU and the SDA terminal of EEPROM.
This is to control over current that may occur when PMOS of the microcontroller and NMOS of EEPROM are turned ON
simultaneously. RS also plays the role of protecting the SDA terminal against surge. Therefore, even when SDA port is
open drain input/output, RS can be used.
ACK
SCL
RPU
RS
SDA
'H' output of microcontroller
'L' output of EEPROM
EEPROM
Microcontroller
Over current flows to SDA line by 'H'
output of microcontroller and 'L'
output of EEPROM.
Figure 45. I/O Circuit Diagram
Figure 46. Input / Output Collision Timing
2. Maximum Value of RS
The maximum value of RS is determined by the following relations:
(1)SDA rise time to be determined by the capacitance (CBUS) of bus line and RPU of SDA should be tR or lower.
Furthermore, AC timing should be satisfied even when SDA rise time is slow.
(2)The bus’ electric potential
should sufficiently secure the input 'L' level (VIL) of microcontroller including recommended noise margin of 0.1Vcc.
A to be determined by RPU and RS the moment when EEPROM outputs 'L' to SDA bus
○
(VCC -VOL) R
S VOL 0.1VCC VIL
VCC
R
PU R
S
A
RPU
RS
V
IL -VOL -0.1V
∴R
S
CC RPU
VOL
1.1VCC -VIL
IOL
Ex)VCC=3V VIL=0.3VCC VOL=0.4V RPU=20kΩ
Bus line
capacity
CBUS
0.33-0.4-0.13
RS
20103
1.13-0.33
VIL
EEPROM
Micro controller
Figure 47. I/O Circuit Diagram
1.67 [k]
3. Minimum Value of RS
The minimum value of RS is determined by over current at bus collision. When over current flows, noises in power source
line and instantaneous power failure of power source may occur. When allowable over current is defined as I, the
following relation must be satisfied. Determine the allowable current in consideration of the impedance of power source
line in set and so forth. Set the over current to EEPROM at 10mA or lower.
V
CC
I
PU
R
R
S
'L'output
V
CC
S
R
Rs
I
Over current I
EX) VCC=3V I=10mA
'H' output
3
Rs
-3
EEPROM
Microcontroller
1010
Figure 48. I/O circuit diagram
300 []
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
19/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
I/O Equivalence Circuit
1. Input (SCL, WP, TEST)
Figure 49. Input Pin Circuit Diagram
2. Input / Output (SDA)
Figure 50. Input / Output Pin Circuit Diagram
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
20/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Power-Up/Down Conditions
At power on, the IC’s internal circuits may go through unstable low voltage area as the Vcc rises, making the IC’s internal
logic circuit not completely reset, hence, malfunction may occur. To prevent this, the IC is equipped with POR circuit and
LVCC circuit. To assure the operation, observe the following conditions at power on.
1. Set SDA = 'H' and SCL ='L' or 'H’
2. Start power source so as to satisfy the recommended conditions of tR, tOFF, and Vbot for operating POR circuit.
tR
Recommended conditions of tR, tOFF,Vbot
VCC
tR
tOFF
Vbot
10ms or below
100ms or below
10ms or larger
10ms or larger
0.3V or below
0.2V or below
tOFF
Vbot
0
Figure 51. Rise Waveform Diagram
3. Set SDA and SCL so as not to become 'Hi-Z'.
When the above conditions 1 and 2 cannot be observed, take the following countermeasures.
(1) In the case when the above condition 1 cannot be observed such that SDA becomes 'L' at power on.
→Control SCL and SDA as shown below, to make SCL and SDA, 'H' and 'H'.
VCC
tLOW
SCL
SDA
After Vcc becomes stable
After Vcc becomes stable
tDH
tSU:DAT
tSU:DAT
Figure 53. When SCL='L' and SDA='L'
Figure 52. When SCL= 'H' and SDA= 'L'
(2) In the case when the above condition 2 cannot be observed.
→After power source becomes stable, execute software reset(Page 16).
(3) In the case when the above conditions 1 and 2 cannot be observed.
→Carry out (1), and then carry out (2).
Low Voltage Malfunction Prevention Function
LVCC circuit prevents data rewrite operation at low power and prevents write error. At LVCC voltage (Typ =1.2V) or below,
data rewrite is prevented.
Noise Countermeasures
1. Bypass Capacitor
When noise or surge gets in the power source line, malfunction may occur, therefore, it is recommended to connect a
bypass capacitor (0.1µF) between the IC’s Vcc and GND pins. Connect the capacitor as close to the IC as possible. In
addition, it is also recommended to attach a bypass capacitor between the board’s Vcc and GND.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
21/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum
rating, increase the board size and copper area to prevent exceeding the Pd rating.
6.
7.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
8.
9.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
22/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Operational Notes – continued
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
12. Regarding the Input Pin of the IC
In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The
operation of these parasitic elements can result in mutual interference among circuits, operational faults, or physical
damage. Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an
input pin lower than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when
no power supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins
have voltages within the values specified in the electrical characteristics of this IC.
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
23/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Part Numbering
B
R C H
0
6 4 G W Z -
3
E 2
BUS type
C：I2C
Revision
Capacity
064=64K
Package
GWZ：UCSP30L1A
Process Code
Packaging and forming specification
E2：: Embossed tape and reel
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
24/26
Datasheet
BRCH064GWZ-3
Physical Dimension Tape and Reel Information
Package Name
UCSP30L1A(BRCH064GWZ-3)3
1PIN MARK
LOT No.
ADM
1.5±0.05
S
S
0.06
6-φ 0.20±0.05
0.05 A B
A
B
B
A
1
2
3
0.35±0.05
P=0.4×2
(Unit : mm)
< Tape and Reel Information >
Tape
Embossed carrier tape
Quantity
6000pcs
E2
Direction of feed
The direction is the pin 1 of product is at the upper left when you
hold reel on the left hand and you pull out the tape on the right hand
1234
1234
1234
1pin
1234
1234
1234
Direction of feed
Reel
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
25/26
TSZ22111･15･001
Datasheet
BRCH064GWZ-3
Marking Diagram
UCSP30L1A(BRCH064GWZ-3)
(TOP VIEW)
1PIN MARK
Part Number Marking
LOT Number
A D M
Revision History
Date
Revision
Changes
16.Jan.2015
11.May.2015
001
002
New Release
Correction of Marking Diagram from ADJM to ADM
www.rohm.com
TSZ02201-0R2R0G100720-1-2
11.May.2015 Rev.002
©2014 ROHM Co., Ltd. All rights reserved.
26/26
TSZ22111･15･001
Daattaasshheeeett
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号：
©2020 ICPDF网 联系我们和版权申明