BU28TD2WNVX-GTL [ROHM]
Fixed Positive LDO Regulator;型号: | BU28TD2WNVX-GTL |
厂家: | ROHM |
描述: | Fixed Positive LDO Regulator 输出元件 调节器 |
文件: | 总12页 (文件大小:560K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
CMOS LDO Regulator Series for Portable Equipments
Versatile Package
FULL CMOS LDO Regulator
BUxxTD2WNVX series
●General Description
●Key Specifications
BUxxTD2WNVX series is high-performance FULL CMOS
regulator with 200-mA output, which is mounted on
versatile package SSON004X1010 (1.00mm × 1.00 mm
× 0.60mm). It has excellent noise characteristics and
load responsiveness characteristics despite its low circuit
current consumption of 35μA. It is most appropriate for
various applications such as power supplies for logic IC,
RF, and camera modules.ROHM’s.
Output voltage:
1.0V to 3.4V
±1.0% (±25mV)
35μA
Accuracy output voltage:
Low current consumption:
Operating temperature range:
-40°C to +85°C
●Applications
Battery-powered portable equipment, etc.
●Package
SSON004X1010 :
1.00mm x 1.00mm x 0.60mm
●Features
High accuracy detection
low current consumption
Compatible with small ceramic capacitor(Cin=Co=0.47uF)
With built-in output discharge circuit
High ripple rejection
ON/OFF control of output voltage
With built-in over current protection circuit
and thermal shutdown circuit
Low dropout voltage
●Typical Application Circuit
STBY
VIN
STBY
VOUT
VOUT
VIN
GND
GND
GND
Fig.1 Application Circuit
○Product structure:Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
・ ・
TSZ22111 14 001
1/9
Datasheet
BUxxTD2WNVX series
●Connection Diagram
SSON004X1010 (TOP VIEW)
4 VIN
3 STBY
LOT Number
1 2
Part Number Marking
1PIN MARK
1 VOUT
2 GND
●Pin Descriptions
SSON004X1010
PIN No.
Symbol
VOUT
GND
Function
Output Voltage
1
2
Grouding
ON/OFF control of output voltage
(High: ON, Low: OFF)
Power Supply Voltage
3
4
STBY
VIN
●Ordering Information
B
U
x
x
T
D
2
W
N
V
X
-
x
T
L
Part
Number
Output Voltage
10 : 1.0V
Low Dropout Voltage
Maximum Output Current
200mA
with
Package
Halogen Free
G : compatible
Packageing and forming specification
Embossed tape and reel
output discharge NVX : SSON004X1010
Blank : incompatible TL : The pin number 1 is the lower left
34 : 3.4V
SSON004X1010
1.0 0.1
<Tape and Reel information>
1PIN MARK
Tape
Embossed carrier tape
5000pcs
Quantity
TL
Direction
of feed
S
The direction is the 1pin of product is at the lower left when you hold
reel on the left hand and you pull out the tape on the left hand
(
)
0.05
0.65 0.05
3-C0.18
R0.05
1
2
45º
4
3
Direction of feed
1pin
0.25 0.05
Reel
Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
∗
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
2/9
Datasheet
F
BUxxTD2WNVX series
●Lineup
Marking
A
6
2
B
1.2V
BU12
3
C
1.5V
BU15
D
1.8V
BU18
E
Output Voltage
1.0V
BU10
1.05V
BU1A
1.15V
BU1B
1.25V
BU1C
1.85V
BU1J
1.9V
BU19
Part Number
G
r
0
1
H
J
K
a
L
2.0V
BU20
2.05V
BU2A
2.1V
BU21
2.3V
BU23
2.5V
BU25
2.6V
BU26
2.7V
BU27
2.75V
BU2H
2.8V
BU28
M
N
P
Q
R
U
Y
2.85V
BU2J
2.9V
BU29
3.0V
BU30
3.1V
BU31
3.2V
BU32
3.3V
BU33
3.4V
BU34
●Absolute Maximum Ratings (Ta=25°C)
PARAMETER
Symbol
Limit
Unit
V
VMAX
Pd
Power Supply Voltage
Power Dissipation
-0.3 ~ +6.5
560(*1)
mW
℃
Maximum junction temperature
Operating Temperature Range
Storage Temperature Range
TjMAX
Topr
+125
-40 ~ +85
-55 ~ +125
℃
Tstg
℃
(*1)Pd deleted at 5.6mW/℃at temperatures above Ta=25℃, mounted on 70×70×1.6 mm glass-epoxy PCB.
● RECOMMENDED OPERATING RANGE (not to exceed Pd)
PARAMETER
Symbol
VIN
Limit
Unit
V
Power Supply Voltage
1.7~6.0
Maximum Output Current
IMAX
200
mA
●OPERATING CONDITIONS
PARAMETER
Symbol
Cin
MIN.
TYP.
0.47
0.47
MAX.
Unit
μF
CONDITION
Input Capacitor
Output Capacitor
0.22(*2)
0.22(*2)
-
-
Ceramic capacitor recommended
Co
μF
(*2)Make sure that the output capacitor value is not kept lower than this specified level across a variety of
temperature, DC bias, changing as time progresses characteristic.
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
・ ・
TSZ22111 15 001
3/9
Datasheet
BUxxTD2WNVX series
●Electrical Characteristics
(Ta=25℃, VIN=VOUT+1.0V (*3), STBY=VIN, Cin=0.47μF, Co=0.47μF, unless otherwise noted.)
Limit
PARAMETER
Symbol
VOUT
Unit
Conditions
MIN.
TYP.
MAX.
Overall Device
VOUT×0.99
VOUT×1.01
VOUT+25mV
60
IOUT=10μA, VOUT≧2.5V
Output Voltage
V
VOUT
VOUT-25mV
IOUT=10μA, VOUT<2.5V
IOUT=0mA
Operating Current
IIN
-
-
35
-
μA
μA
Operating Current (STBY)
ISTBY
1.0
STBY=0V
Ripple Rejection Ratio
RR
45
-
70
-
dB
mV
mV
mV
mV
VRR=-20dBv, fRR=1kHz, IOUT=10mA
2.5V≦VOUT≦2.6V (VIN=0.98*VOUT, IOUT=200mA)
2.7V≦VOUT≦2.85V (VIN=0.98*VOUT, IOUT=200mA)
2.9V≦VOUT≦3.1V (VIN=0.98*VOUT, IOUT=200mA)
3.2V≦VOUT≦3.4V (VIN=0.98*VOUT, IOUT=200mA)
280
260
240
220
540
500
460
420
-
Dropout Voltage
VSAT
-
-
Line Regulation
Load Regulation
VDL
-
-
2
20
80
mV
mV
VIN=VOUT+1.0V to 5.5V (*4), IOUT=10μA
IOUT=0.01mA to 100mA
VDLO
10
Over Current Protection (OCP)
Limit Current
ILMAX
220
20
400
70
700
150
mA
mA
Vo=VOUT*0.95
Vo=0V
Short Current
ISHORT
Standby Block
Discharge Resistor
STBY Pin Pull-down Current
RDSC
ISTB
20
0.1
50
0.6
-
80
2.0
5.5
0.3
Ω
μA
V
VIN=4.0V, STBY=0V, VOUT=4.0V
STBY=1.5V
ON
STBY Control Voltage
OFF
VSTBH
VSTBL
1.2
-0.3
-
V
This product is not designed for protection against radioactive rays.
(*3) VIN=2.5V for VOUT≦1.5V
(*4) VIN=2.5V to 3.6V for VOUT≦1.5V
●ELECTRICAL CHARACTERISTICS of each Output Voltage
(Ta=25℃, STBY=VIN, Cin=0.47μF, Co=0.47μF, unless otherwise noted.)
Output Voltage
PARAMETER
MIN.
80
TYP.
MAX.
Unit
mA
Conditions
VIN=1.7V
160
-
-
-
-
-
-
1.0V,1.15V,1.2V,1.25V
200
60
VIN=2.1V
Maximum
120
-
VIN=1.8V
output current
1.5V
200
200
VIN=2.2V
1.8V,1.85V,1.9V,2.0V,2.05V,2.1V,2.3V
-
VIN=VOUT+0.6V
●Block Diagrams
VIN
VIN
4
VREF
VOUT
VOUT
Cin
1
2
OCP
GND
Co
TSD
STBY
Discharge
STBY
STBY
Cin・・・0.47μF (Ceramic)
Co ・・・0.47μF (Ceramic)
3
Fig. 2 Block Diagrams
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
4/9
Datasheet
BUxxTD2WNVX series
●Reference data BU18TD2WNVX (Ta=25ºC unless otherwise specified.)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
1.85
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
100
80
60
40
20
0
Temp=25°C
Temp=25°C
VIN=STBY
Io=0uA
VIN=STBY
Temp=85°C
Temp=25°C
Io=0uA
Io=100uA
Io=50mA
Io=200mA
Io=0uA
Io=100uA
Io=50mA
Io=200mA
Temp=-40°C
VIN=STBY
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
0.2
85
Input Voltage (V)
Input Voltage (V)
Input Voltage (V)
Fig 5. Circuit Current IGND
Fig 3. Output Voltage
Fig 4. Line Regulation
1.85
1.84
1.83
1.82
1.81
1.6
1.4
1.2
1.0
0.8
0.6
100
80
60
40
20
0
VIN=2.8V
VIN=2.8V
STBY=1.5V
STBY=1.5V
Temp=85°C
Temp=25°C
Temp=85°C
Temp=85°C
1.80
1.79
1.78
1.77
1.76
1.75
Temp=-40°C
0.4
0.2
0.0
Temp=25°C
Temp=-40°C
Temp=25°C
Temp=-40°C
0.05
0
0.05
0.1
0.15
0.2
1.5
85
0
0.1
0.15
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
Output Current (A)
Output Current (A)
Input Voltage (V)
Fig 6. VSTBY - ISTBY
Fig 8. Load Regulation
Fig 7. IOUT - IGND
1.85
1.84
1.83
1.82
1.81
1.80
1.79
1.78
1.77
1.76
1.75
2.0
1.8
1.6
1.4
1.2
2.0
VIN=2.8V
STBY=1.5V
Io=0.1mA
VIN=3.8V
Io=0mA
VIN=2.8V
1.5
1.0
0.5
0.0
VIN=5.5V
VIN=2.3V
1.0
0.8
0.6
0.4
0.2
0.0
Temp=25°C
Temp=85°C
Temp=-40°C
Temp=25°C
STBY=1.5V
0
0.5
1
-40
-15
10
35
60
0.0
0.1
0.2
0.3
0.4
0.5
0.6
Temp (°C)
STBY Voltage (V)
Output Current (mA)
Fig 9. OCP Threshold
Fig 11. VOUT - Temp
Fig 10. STBY Threshold
60
50
40
30
20
10
0
1.0
0.9
0.8
0.7
0.6
VIN=2.8V
STBY=1.5V
Io=0mA
VIN=2.8V
STBY=0V
0.5
0.4
0.3
0.2
0.1
0.0
-40
-15
10
35
60
85
-40
-15
10
35
60
Temp (°C)
Temp (°C)
Fig 12. IGND - Temp
Fig 13. IGND - Temp (STBY)
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
5/9
Datasheet
BUxxTD2WNVX series
●Reference data BU18TD2WNVX (Ta=25ºC unless otherwise specified.)
100
100
50
0
50
IOUT=0mA→50mA
IOUT=50mA→0mA
0
1.90
1.85
1.85
1.80
1.80
1.75
1.75
1.70
Fig 14. Load Response
Fig 15. Load Response
100
50
0
100
50
0
IOUT=0mA→100mA
IOUT=100mA→0mA
1.90
1.85
1.85
1.80
1.80
1.75
1.75
1.70
Fig 16. Load Response
Fig 17. Load Response
200
100
0
200
100
0
IOUT=0mA→200mA
IOUT=200mA→0mA
2.00
1.90
1.90
1.80
1.80
1.70
1.70
1.60
Fig 18. Load Response
Fig 19. Load Response
100
50
0
100
50
0
IOUT=50mA→100mA
IOUT=100mA→50mA
1.90
1.80
1.85
1.80
1.75
1.70
1.70
1.60
Fig 21. Load Response
Fig 20. Load Response
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
6/9
Datasheet
BUxxTD2WNVX series
●Reference data BU18TD2WNVX (Ta=25ºC unless otherwise specified.)
2.0
1.0
0.0
2.0
STBY=0→1.5V
STBY=0→1.5V
1.0
0.0
2.0
1.0
2.0
1.0
0.0
0.0
Fig 23. Start Up Time
Iout=200mA
Fig 22. Start Up Time
Iout=0mA
4.0
4.0
2.0
0.0
VIN=STBY=0→2.8V
2.0
0.0
VIN=STBY=2.8→0V
2.0
1.0
2.0
1.0
0.0
0.0
Fig 25. Start Up Time
(VIN=STBY) Iout=200mA
Fig 24. Start Up Time
(VIN=STBY) Iout=0mA
Iout=0mA
2.0
1.0
0.0
4.8
3.8
2.8
VIN=2.8V→3.8V→2.8V
STBY=1.5→0V
1.81
2.0
1.0
1.80
1.79
1.78
0.0
Fig 26. Discharge Time
Fig 27. VIN Response
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
7/9
Datasheet
BUxxTD2WNVX series
z About power dissipation (Pd)
As for power dissipation, an approximate estimate of the heat reduction characteristics and internal power consumption of
IC are shown, so please use these for reference. Since power dissipation changes substantially depending on the
implementation conditions (board size, board thickness, metal wiring rate, number of layers and through holes, etc.), it is
recommended to measure Pd on a set board. Exceeding the power dissipation of IC may lead to deterioration of the
original IC performance, such as causing operation of the thermal shutdown circuit or reduction in current capability.
Therefore, be sure to prepare sufficient margin within power dissipation for usage.
Calculation of the maximum internal power consumption of IC (PMAX)
PMAX=(VIN-VOUT)×IOUT(MAX.) (VIN: Input voltage VOUT: Output voltage IOUT(MAX): Maximum output current)
{ Measurement conditions
Standard ROHM Board
Top Layer (Top View)
Bottom Layer (Top View)
Evaluation Board 1
Layout of Board for
Measurement
Top Layer (Top View)
IC
Implementation
Position
Bottom Layer (Top View)
Measurement State
Board Material
Board Size
With board implemented (Wind speed 0 m/s) With board implemented (Wind speed 0 m/s)
Glass epoxy resin (Double-side board)
70 mm x 70 mm x 1.6 mm
Glass epoxy resin (Double-side board)
40 mm x 40 mm x 1.6 mm
Top layer
Metal (GND) wiring rate: Approx. 0%
Metal (GND) wiring rate: Approx. 50%
Wiring
Bottom
Rate
Metal (GND) wiring rate: Approx. 50%
Metal (GND) wiring rate: Approx. 50%
layer
Through Hole
Diameter 0.5mm x 6 holes
0.56W
Diameter 0.5mm x 25 holes
0.39W
Power Dissipation
Thermal Resistance
θja=178.6°C/W
θja=256.4°C/W
0.6
0.56W
0.5
0.4
0.39W
0.3
0.2
0.1
0
* Please design the margin so that
PMAX becomes is than Pd (PMAX<Pd)
within the usage temperature range
0
25
50
75
100
125
85
Ta [
]
℃
Fig. 28 SSON004X1010 Power dissipation heat reduction characteristics (Reference)
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
8/9
Datasheet
BUxxTD2WNVX series
●Operation Notes
1.) Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings (such as the input voltage or operating temperature range) may result in
damage to the IC. Assumptions should not be made regarding the state of the IC (e.g., short mode or open mode) when such damage
issuffered. Ifoperationalvaluesareexpectedtoexceedthemaximumratingsforthedevice, consideraddingprotectivecircuitry
(such as fuses) to eliminate the risk of damaging the IC.
2.) GND potential
The potential of the GND pin must be the minimum potential in the system in all operating conditions.
Never connect a potential lower than GND to any pin, even if only transiently.
3.) Thermal design
Use a thermal design that allows for a sufficient margin for that package power dissipation rating (Pd) under actual operating
conditions.
4.) Inter-pin shorts and mounting errors
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting or
shorts between pins may result in damage to the IC.
5.) Operation in strong electromagnetic fields
Strong electromagnetic fields may cause the IC to malfunction. Caution should be exercised in applications where strong
electromagnetic fields may be present.
6.) Common impedance
Wiring traces should be as short and wide as possible to minimize common impedance. Bypass capacitors should
be use to keep ripple to a minimum.
7.) Voltage of STBY pin
To enable standby mode for all channels, set the STBY pin to 0.3 V or less, and for normal operation, to 1.2 V or more. Setting
STBY to a voltage between 0.3 and 1.2 V may cause malfunction and should be avoided. Keep transition time between high and
low (or vice versa) to a minimum.
Additionally, if STBY is shorted to VIN, the IC will switch to standby mode and disable the output discharge circuit, causing
a temporary voltage to remain on the output pin. If the IC is switched on again while this voltage is present, overshoot may
occur on the output. Therefore, in applications where these pins are shorted, the output should always be completely discharged
before turning the IC on.
8.) Over-current protection circuit (OCP)
This IC features an integrated over-current and short-protection circuitry on the output to prevent destruction of the IC when
the output is shorted. The OCP circuitry is designed only to protect the IC from irregular conditions (such as motor output
shorts) and is not designed to be used as an active security device for the application. Therefore, applications should not
be designed under the assumption that this circuitry will engage.
9.) Thermal shutdown circuit (TSD)
This IC also features a thermal shutdown circuit that is designed to turn the output off when the junction temperature of the
IC exceeds about 150℃. This feature is intended to protect the IC only in the event of thermal overload and is not designed
to guarantee operation or act as an active security device for the application. Therefore, applications should not be designed
under the assumption that this circuitry will engage.
10.) Input/output capacitor
Capacitors must be connected between the input/output pins and GND for stable operation, and should be physically mounted as
close to the IC pins as possible. The input capacitor helps to counteract increases in power supply impedance, and increases
stability in applications with long or winding power supply traces. The output capacitance value is directly related to the
Unstable region
overall stability and transient response of the regulator, and should be set to the largest por the application
toincreasethesecharacteristics.Duringdesign, keepinmindthatingeneral,ceramiccapacitorshaveawiderangeoftolerances,
temperature coefficients and DC bias characteristics, and that their capacitance values tend to decrease over time. Confirm
these details before choosing appropriate capacitors for your application.(Please refer the technical note, regarding ceramic
capacitor of recommendation)
Cout=0.47μF, Cin=0.47μF, Temp=+25℃
11.) About the equivalent series resistance (ESR) of a ceramic capacitor
100
Capacitors generally have ESR (equivalent series resistance)
and it operates stably in the ESR-IOUT area shown on the right.
10
Since ceramic capacitors, tantalum capacitors, electrolytic
capacitors, etc. generally have different ESR, please check
1
the ESR of the capacitor to be used and use it within the
stability area range shown in the right graph for evaluation
of the actual application.
0.1
0.01
0
50
100
150
200
IOUT [mA]
Fig. 29 Stable region (example)
www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved.
・ ・
TSZ02201-0RBR0A300050-1-2
7.FEB.2013.Rev.001
TSZ22111 15 001
9/9
Daattaasshheeeett
Notice
●General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
●Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3) Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4) The Products are not subject to radiation-proof design.
5) Please verify and confirm characteristics of the final or mounted products in using the Products.
6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8) Confirm that operation temperature is within the specified range described in the product specification.
9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2) You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
●Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
●Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
●Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
●Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
●Precaution Regarding Intellectual Property Rights
1) All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
●Other Precaution
1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
5) The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.
相关型号:
BU28TD2WNVX-TL
Fixed Positive LDO Regulator, 2.8V, 0.5V Dropout, CMOS, PDSO4, 1 X 1 MM, 0.60 MM HEIGHT, ROHS COMPLIANT, SSON-4
ROHM
©2020 ICPDF网 联系我们和版权申明