BU4234
更新时间:2024-09-18 08:18:26
品牌:ROHM
描述:Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series
BU4234 概述
Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series 低压免费延时时间设定CMOS电压检测器IC系列
BU4234 数据手册
通过下载BU4234数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Voltage Detector IC Series
Low Voltage Free Delay Time Setting
CMOS Voltage Detector IC Series
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
No.09006ECT02
●Description
ROHM CMOS reset IC series with adjustable output delay is a high-accuracy low current consumption reset IC series with
a built-in delay circuit. The lineup was established with two output types (Nch open drain and CMOS output) and detection
voltages range from 0.9V to 4.8V in increments of 0.1V, so that the series may be selected according to the application at hand.
●Features
1) Detection voltage from 0.9V to 4.8V in 0.1V increments
2) Highly accurate detection voltage: ±1.0%
3) Ultra-low current consumption
4) Nch open drain output
5) Small surface package
(BU42□□G/F/FVE)and CMOS output (BU43□□G/F/FVE)
SSOP5: BU42□□G,BU43□□G
SOP4: BU42□□F,BU43□□F
VSOF5: BU42□□FVE,BU43□□FVE
●Applications
All electronics devices that use microcontrollers and logic circuits.
●Selection Guide
No.
Specifications
Description
①
Output Circuit Format
Detection Voltage
Package
2:Open Drain Output, 3:CMOS Output
Part Number : BU4
Example VDET: Represented as 0.1V steps in the
range from 0.9V to 4.8V
②
③
1
2
3
(Displayed as 0.9 in the case of 0.9V)
G:SSOP5(SMP5C2)/ F:SOP4/ FVE:VSOF5(EMP5)
● Lineup
Detection
voltage
Part
Detection
voltage
Part
Number
Detection
Part
Number
Detection
voltage
Part
Number
Making
Making
Making
Making
Number
BU4248
BU4247
BU4246
BU4245
BU4244
BU4243
BU4242
BU4241
BU4240
BU4239
BU4238
BU4237
BU4236
BU4235
BU4234
BU4233
BU4232
BU4231
BU4230
BU4229
voltage
4.8V
4.7V
4.6V
4.5V
4.4V
4.3V
4.2V
4.1V
4.0V
3.9V
3.8V
3.7V
3.6V
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
ZR
ZQ
ZP
ZN
ZM
ZL
4.8V
4.7V
4.6V
4.5V
4.4V
4.3V
4.2V
4.1V
4.0V
3.9V
3.8V
3.7V
3.6V
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
YV
YU
YT
YS
YR
YQ
YP
YN
YM
YL
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
1.1V
1.0V
0.9V
BU4228
BU4227
BU4226
BU4225
BU4224
BU4223
BU4222
BU4221
BU4220
BU4219
BU4218
BU4217
BU4216
BU4215
BU4214
BU4213
BU4212
BU4211
BU4210
BU4209
1H
1G
1F
1E
1D
1C
1B
1A
0Z
0Y
0X
0W
0V
0U
0T
0S
0R
0Q
0P
0N
BU4348
BU4347
BU4346
BU4345
BU4344
BU4343
BU4342
BU4341
BU4340
BU4339
BU4338
BU4337
BU4336
BU4335
BU4334
BU4333
BU4332
BU4331
BU4330
BU4329
0M
0L
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
1.1V
1.0V
0.9V
BU4328
BU4327
BU4326
BU4325
BU4324
BU4323
BU4322
BU4321
BU4320
BU4319
BU4318
BU4317
BU4316
BU4315
BU4314
BU4313
BU4312
BU4311
BU4310
BU4309
0K
0J
0H
0G
0F
0E
0D
0C
0B
0A
ZZ
ZY
ZX
ZW
ZV
ZU
ZT
ZS
ZK
ZJ
ZH
ZG
ZF
ZE
ZD
ZC
ZB
ZA
YZ
YY
YX
YW
YK
YJ
YH
YG
YF
YE
YD
YC
YB
YA
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
1/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Absolute maximum ratings (Ta=25°C)
Parameter
Power Supply Voltage
Symbol
Limits
-0.3 ~ +7
Unit
VDD-GND
V
Nch Open Drain Output
GND-0.3 ~ +7
GND-0.3 ~ VDD+0.3
540
Output Voltage
VOUT
V
CMOS Output
SSOP5
*1*4
*2*4
*3*4
Power
Dissipation
SOP4
Pd
400
mW
VSOF5
210
Operating Temperature
Topr
Tstg
-40 ~ +125
-55 ~ +125
°C
°C
Ambient Storage Temperature
*1
*2
*3
*4
When used at temperatures higher than Ta=25°C, the power is reduced by 5.4mW per 1°C above 25°C.
When used at temperatures higher than Ta=25°C, the power is reduced by 4.0mW per 1°C above 25°C.
When used at temperatures higher than Ta=25°C, the power is reduced by 2.1mW per 1°C above 25°C.
When a ROHM standard circuit board (70mm×70mm×1.6mm, glass epoxy board)is mounted.
●Electrical characteristics (Unless Otherwise Specified Ta=-40 to 105°C)
Limit
Parameter
Symbol
VDET VDD=HL, Ta=25°C, RL=470kΩ
VDET =0.9-1.3V
Condition
Unit
V
Min.
Typ.
Max.
Vdet(T)
×0.99
Vdet(T)
×1.01
Detection Voltage
Vdet(T)
-
0.15
0.20
0.25
0.30
0.35
0.40
0.30
0.35
0.40
0.45
0.50
0.55
-
0.88
1.05
1.23
1.40
1.58
1.75
1.40
1.58
1.75
1.93
2.10
2.28
-
VDET =1.4-2.1V
VDET =2.2-2.7V
VDET =2.8-3.3V
VDET =3.4-4.2V
VDET =4.3-4.8V
VDET =0.9-1.3V
VDET =1.4-2.1V
VDET =2.2-2.7V
VDET =2.8-3.3V
VDET =3.4-4.2V
VDET =4.3-4.8V
-
-
Circuit Current when ON
Circuit Current when OFF
Idd1
VDD=VDET-0.2V
µA
-
-
-
-
-
-
Idd2
VDD=VDET+2.0V
µA
V
-
-
-
VOL≤0.4V, Ta=25~125°C, RL=470kΩ
VOL≤0.4V, Ta=-40~25°C, RL=470kΩ
VDS=0.5V VDD=6.0V VDET=4.0-4.8V
VDS=0.05V VDD=0.85V
0.70
0.90
2.0
20
1.0
3.6
-
Operating Voltage Range
‘High’ Output Current (Pch)
Vopl
IOH
-
-
4.0
-
mA
µA
100
3.3
-
‘Low’ Output Current (Nch)
Iol
VDS=0.5V VDD=1.5V VDET=1.7-4.8V
VDS=0.5V VDD=2.4V VDET=2.7-4.8V
VDD=VDS=7V Ta=-40~85°C
-
mA
µA
6.5
-
0
0.1
1
Leak Current when OFF
Ileak
Ioh
VDD=VDS=7V Ta=85~125°C
-
0
VDS=0.5V VDD=4.8V VDET=0.9-3.9V
1.7
3.4
-
‘High’ Output Current (Pch)
mA
VDS=0.5V VDD=6.0V VDET=4.0-4.8V
VDD=VDET×1.1, VDET=0.9-2.5V Ta=25°C
RL=470kΩ
VDD=VDET×1.1, VDET=2.6-4.8V Ta=25°C
RL=470kΩ
2.0
Vdd
×0.35
Vdd
×0.40
9
4.0
Vdd
×0.45
Vdd
×0.50
10
-
Vdd
×0.55
Vdd
×0.60
11
CT pin Threshold Voltage
Vcth
V
*1
Output Delay Resistance
CT pin Output Current
Rct
Ict
VDD=VDET×1.1 VCT=0.5V Ta=25°C
MΩ
VCT=0.1V VDD=0.85V
5
40
-
-
µA
VCT=0.5V VDD=1.5V VDET=1.7-4.8V
200
400
Detection Voltage
Temperature coefficient
Vdet/∆T Ta=-40°C ~125°C
-
±30
-
ppm/°C
V
Vdet
×0.03
Vdet
×0.05
Vdet
×0.08
VDET≤1.0V
VDET≥1.1V
VDD=LHL
∆VDET Ta=-40~125°C
RL=470kΩ
Hysteresis Voltage
Vdet
×0.03
Vdet
×0.05
Vdet
×0.07
*1: Designed guarantee. (Outgoing inspection is not done all products.)
DET(T) : Standard Detection Voltage(0.9V to 4.8V, 0.1V step)
RL: Pull-up resistor to be connected between VOUT and power supply.
V
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
2/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Block Diagrams
BU42□□G/F/FVE
BU43□□G/F/FVE
V
DD
VDD
VOUT
VOUT
Vref
Vref
GND
CT
GND
CT
Fig.1
Fig.2
TOP VIEW
TOP VIEW
TOP VIEW
SSOP5
SOP4
VSOF5
PIN No.
Symbol
VOUT
VDD
Function
Reset output
PIN No.
Symbol
GND
Function
GND
PIN No.
Symbol
Function
Reset output
Substrate*
1
2
3
4
1
2
1
2
VOUT
SUB
Power supply voltage
GND
VDD
Power supply voltage
Capacitor connection terminal
for output delay time
Capacitor connection terminal
for output delay time
GND
3
4
CT
3
CT
N.C.
Unconnected terminal
VOUT
Reset output
4
5
VDD
GND
Power supply voltage
GND
Capacitor connection
terminal for output delay time
5
CT
*Connect the substrate to VDD
www.rohm.com
2009.11 - Rev.C
3/11
© 2009 ROHM Co., Ltd. All rights reserved.
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Reference Data (Unless specified otherwise, Ta=25°C)
0.6
0.5
0.4
0.3
0.2
0.1
0.0
5
4
3
2
1
0
25
20
15
10
5
BU4318G
【
】
BU4216F
【
】
VDD=6.0V
VDD=4.8V
VDD=1.2V
0
0
1
2
3
4
5
6
7
0.0
DRAIN-SOURCE VOLTAGE VDS[V]
:
0.5
1.0
1.5
2.0
2.5
0
1
2
3
4
5
6
VDD SUPPLY VOLTAGE VDD[V]
:
DRAIN-SOURCE VOLTAGE
VDS[V]
:
Fig.3 Circuit Current
Fig.4 “LOW” Output Current
Fig.5 “High” Output Current
700
600
500
400
300
200
100
0
7
6
5
4
3
2
1
0
1.0
0.8
0.6
0.4
0.2
0.0
BU4216F
BU4216F
【
【
】
】
BU4216F
【
】
0
1
2
3
4
5
6
7
0.0
0.5
1.0
1.5
2.0
2.5
0
0.5
1
1.5
2
2.5
VDD SUPPLY VOLTAGE VDD[V]
:
VDD SUPPLY VOLTAGE VDD[V]
V
DD SUPPLY VOLTAGE VDD[V]
:
:
Fig.7 Operating Limit Voltage
Fig.8 Ct Terminal Current
Fig.6 I/O Characteristics
2.0
1.5
1.0
0.5
1.0
0.8
0.6
0.4
0.2
0.0
BU4216F
【
】
BU4216F
【
】
Low to high(VDET+ΔVDET
)
0.4
0.3
0.2
0.1
0.0
High to low(VDET
)
BU4216F
0
【
】
-40
40
80
120
-40
0
40
80
120
-40
0
40
80
120
TEMPERATURE Ta[
]
℃
:
TEMPERATURE Ta[
]
℃
:
TEMPERATURE Ta[
]
℃
:
Fig.9 Detecting Voltage
Release Voltage
Fig.11 Circuit Current when OFF
Fig.10 Circuit Current when ON
18
1.0
0.5
0.0
10000
BU4216F
【
BU4216F
【
BU4216F
【 】
】
】
16
14
12
10
8
1000
100
10
1
6
0.1
4
0.01
2
0
0.001
-40
0
40
TEMPERATURE Ta[ ]
℃
80
120
-40
0
40
80
120
0.0001
0.001
0.01
0.1
TEMPERATURE Ta[
]
℃
:
:
CAPACITANCE OF CT CCT[μF]
:
Fig.13 Ct Terminal Circuit Resistance
Fig.12 Operating Limit Voltage
Fig.14 Delay Time (TPLH) and
CT Terminal External Capacitance
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
4/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Setting of Detector Delay Time
This detector IC can be set delay time at the rise of VDD by the capacitor connected to CT terminal.
Delay time at the rise of VDD TPLH:Time until when Vout rise to 1/2 of VDD after VDD rise up and beyond the release
voltage(VDET+∆VDET
)
V
DD-VCTH
TPLH=-1×CCT×RCT×ln
VDD
CCT
RCT
:
:
CT pin Externally Attached Capacitance
CT pin Internal Impedance(P.2 RCT refer.) Ln:
VCTH
Natural Logarithm
:
CT pin Threshold Voltage(P.2 VCTH refer.)
●Reference Data of Falling Time (TPHL) Output
Examples of Falling Time (TPHL) Output
Part Number
BU4245G
BU4345G
T
PHL [µs]
275.7
359.3
* This data is for reference only.
The figures will vary with the application, so please confirm actual operating conditions before use.
●Explanation of Operation
For both the open drain type(Fig.15)and the CMOS output type(Fig.16), the detection and release voltages are used as
threshold voltages. When the voltage applied to the Vdd pins reaches the applicable threshold voltage, the Vout terminal
voltage switches from either “High” to “Low” or from “Low” to “High”. BU42□□G/F/FVE and BU43□□G/F/FVE have delay
time function which set TPLH (Output “Low””High”) using an external capacitor (CCT). Because the BU42□□G/F/FVE
series uses an open drain output type, it is possible to connect a pull-up resistor to VDD or another power supply [The
output “High” voltage (VOUT) in this case becomes VDD or the voltage of the other power supply].
VDD
VDD
VDD
Q2
Q1
R1
R2
R1
R2
VDD
Vref
RESET
Vref
RESET
VOUT
VOUT
Q1
Q3
Q3
R3
R3
GND
GND
CT
CT
Fig.15 (BU42□□ type internal block diagram)
Fig.16 (BU43□□ type internal block diagram)
●Timing Waveforms
Example: the following shows the relationship between the input voltage VDD, the CT Terminal Voltage VCT and the output
voltage VOUT when the input power supply voltage VDD is made to sweep up and sweep down (The circuits are those in
Fig.15 and 16).
① When the power supply is turned on, the output is unsettled from
after over the operating limit voltage (VOPL) until TPHL. There fore it is
VDET+ΔVDET
possible that the reset signal is not outputted when the rise time of
VDD is faster than TPHL.
② When VDD is greater than VOPL but less than the reset release
voltage (VDET+∆VDET), the CT terminal (VCT) and output (VOUT)
voltages will switch to L.
⑤
VDET
DD
V
VOPL
0V
1/2 VDD
③ If VDD exceeds the reset release voltage (VDET+VDET), then VOUT
switches from L to H (with a delay to the CT terminal).
④ If VDD drops below the detection voltage (VDET) when the power
supply is powered down or when there is a power supply fluctuation,
VOUT switches to L (with a delay of TPHL).
⑤ The potential difference between the detection voltage and the
release voltage is known as the hysteresis width (VDET). The system
is designed such that the output does not flip-flop with power supply
fluctuations within this hysteresis width, preventing malfunctions due
to noise.
CT
V
TPLH
TPHL
TPLH
TPHL
OUT
V
①
②
③
④
Fig.17
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
5/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Circuit Applications
1) Examples of a common power supply detection reset circuit
Application examples of BU42□□G/F/FVE series
VDD1
VDD2
(Open Drain output type) and BU43□□G/F/FVE series
(CMOS output type) are shown below.
RL
Microcontroller
RST
CASE1:The power supply of the microcontroller (Vdd2)
differs from the power supply of the reset detection
(Vdd1).
BU42□□□
CT
CIN
Use the Open Drain Output Type (BU42□□G/FVE)
attached a load resistance (RL) between the output and
Vdd2. (As shown Fig.18)
CL
(Capacitor for
noise filtering)
GND
CASE2:The power supply of the microcontroller (Vdd1) is
same as the power supply of the reset detection (Vdd1).
Use CMOS output type (BU43□□G/FVE) or Open Drain
Output Type (BU42□□G/FVE) attached a load
resistance (RL) between the output and Vdd1.
(As shown Fig.19)
Fig.18 Open collector Output type
VDD1
Microcontroller
R
ST
When a capacitance CL for noise filtering is connected to
the Vout pin (the reset signal input terminal of the
microcontroller), please take into account the waveform
of the rise and fall of the output voltage (Vout).
BU43□□□
CIN
CT
CL
(Capacitor for
noise filtering)
GND
Fig.19 CMOS Output type
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
6/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
2) Examples of the power supply with resistor dividers
In applications where the power supply input terminal (VDD) of an IC with resistor dividers, it is possible that a through
current will momentarily flow into the circuit when the output logic switches, resulting in malfunctions (such as output
oscillatory state).
(Through-current is a current that momentarily flows from the power supply (VDD) to ground (GND) when the output level
switches from “High” to “Low” or vice versa.)
V1
IDD
R2
I1
Through
Current
DD
V
BU42□□
BU43□□
R1
OUT
V
CIN
L
C
GND
VDD
VDET
0
Fig.20
A voltage drop of [the through-current (I1)] × [input resistor (R2)] is caused by the through current, and the input voltage
to descends, when the output switches from “Low” to “High”. When the input voltage decreases and falls below the
detection voltage, the output voltage switches from “High” to “Low”. At this time, the through-current stops flowing through
output “Low”, and the voltage drop is eliminated. As a result, the output switches from “Low” to “High”, which again
causes the through current to flow and the voltage drop. This process is repeated, resulting in oscillation.
Consider the use of BU42□□ when the power supply input it with resistor dividers.
VDD - IDD Peak Current Ta=25°C
Temp - IDD(BU42xx)
BU43xx
BU42xx
BD52xx
BD53xx
VDD3V
VDD6V
VDD7V
VDD4V
10
1
2.5
2.0
1.5
1.0
0.5
0.0
0.1
0.01
0.001
-50 -30 -10 10 30 50 70 90 110 130
Temp
3
4
5
6
7
8
9
10
VDD[V]
Fig.21 Current Consumption vs. Power Supply Voltage
* This data is for reference only.
The figures will vary with the application, so please confirm actual operating conditions before use.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
7/11
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Notes for use
1. Absolute maximum range
Absolute Maximum Ratings are those values beyond which the life of a device may be destroyed. We cannot be defined the
failure mode, such as short mode or open mode. Therefore a physical security countermeasure, like fuse, is to be given
when a specific mode to be beyond absolute maximum ratings is considered.
2 . GND potential
GND terminal should be a lowest voltage potential every state.
Please make sure all pins that are over ground even if include transient feature.
3 . Electrical Characteristics
Be sure to check the electrical characteristics, that are one the tentative specification will be changed by temperature,
supply voltage, and external circuit.
4 . Bypass Capacitor for Noise Rejection
Please put into the to reject noise between VDD pin and GND with 1uF over and between VOUT pin and GND with 1000pF.
If extremely big capacitor is used, transient response might be late. Please confirm sufficiently for the point.
5 . Short Circuit between Terminal and Soldering
Don’t short-circuit between Output pin and VDD pin, Output pin and GND pin, or VDD pin and GND pin. When soldering the
IC on circuit board please is unusually cautious about the orientation and the position of the IC. When the orientation is
mistaken the IC may be destroyed.
6 . Electromagnetic Field
Mal-function may happen when the device is used in the strong electromagnetic field.
7 . The VDD line inpedance might cause oscillation because of the detection current.
8 . A VDD -GND capacitor (as close connection as possible) should be used in high VDD line impedance condition.
9 . Lower than the mininum input voltage makes the VOUT high impedance, and it must be VDD in pull up (VDD) condition.
10. Case of needless Delay time, recommended to insert more 470kΩ resister between VDD and CT.
Recommended value of RL Resistar is over 50kΩ (VDET=1.5~4.8V),over 100kΩ (VDET=0.9~1.4V).
12.This IC has extremely high impedance terminals. Small leak current due to the uncleanness of PCB surface might cause
unexpected operations. Application values in these conditions should be selected carefully. If 10MΩ leakage is assumed
between the CT terminal and the GND terminal, 1MΩ connection between the CT terminal and the VDD terminal would be
recommended. Also, if the leakage is assumed between the VOUT terminal and the GND terminal, the pull up resistor
should be less than 1/10 of the assumed leak resistance.
The value of RCT depends on the external resistor that is connected to CT terminal, so please consider the delay time
that is decided by τ × RCT × CCT changes.
www.rohm.com
2009.11 - Rev.C
8/11
© 2009 ROHM Co., Ltd. All rights reserved.
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
13. Delay time (tPLH)
tPLH = τ × RCT × CCT (sec)
τ: time constant
RCT : 10MΩ (typ.) (built-in resistor)
CCT : capacitor connected CT pin.
Recommended value of CCT capacitor is over 100pF.
The reference value
(τ × RCT) ×106
VDET = 0.9 to 2.5V
Ta = 25°C
(min. = 5.1 × 106 typ.= 6.0 × 106 max = 6.9 × 106)
Ta = -25 to 125°C (min. = 3.3 × 106 typ. = 6.0 × 106 max = 8.7 × 106)
VDET = 2.6 to 4.8V
Ta = 25°C
(min. = 5.9 × 106 typ.= 6.9 × 106 max = 7.9 × 106)
Ta = -25 to 125°C (min. = 3.8 × 106 typ.= 6.9 × 106 max = 10.0 × 106)
14.External parameters
The recommended parameter range for CT is 100pF~0.1µF. For RL, the recommended range is 50kΩ~1MΩ. There
are many factors (board layout, etc) that can affect characteristics. Please verify and confirm using practical applications.
15. CT pin discharge
Due to the capabilities of the CT pin discharge transistor, the CT pin may not completely discharge when a short input
pulse is applied, and in this case the delay time may not be controlled. Please verify the actual operation.
16. Power on reset operation
Please note that the power on reset output varies with the Vcc rise up time. Please verify the actual operation.
17. Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC.
Therefore, be certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
18. When the power supply, is turned on because of in certain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
www.rohm.com
2009.11 - Rev.C
9/11
© 2009 ROHM Co., Ltd. All rights reserved.
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
●Part Number Selection
B
U
4
2
0
9
G
-
T
R
BU42: Adjustable Delay Time
CMOS Reset IC
Detection voltage
09 : 0.9V (0.1V step)
48 : 4.8V
Package
Taping Specifications
G: SSOP5
F: SOP4
TR: Embossed tape and reel
Open Drain Type
Output Type
FVE: VSOF5
BU43: Adjustable Delay Time
CMOS Reset IC
CMOS Output Type
SSOP5
<Tape and Reel information>
°
°
+
−4
2.9 0.2
6
°
4
Tape
Embossed carrier tape
3000pcs
5
4
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
1pin
+0.05
0.13
−0.03
+0.05
−0.04
0.42
0.1
0.95
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
Reel
(Unit : mm)
∗
SOP4
<Tape and Reel information>
2.0 0.2
Tape
Embossed carrier tape
°
°
+6
–4
1.3
3
°
4
Quantity
3000pcs
4
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
0.05
+0.05
–0.03
0.13
1pin
S
+0.05
–0.04
0.42
0.1
S
+0.05
–0.04
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
0.32
Reel
(Unit : mm)
∗
www.rohm.com
2009.11 - Rev.C
10/11
© 2009 ROHM Co., Ltd. All rights reserved.
BU42□□G series, BU42□□F series, BU42□□FVE series,
BU43□□G series, BU43□□F series, BU43□□FVE series
Technical Note
VSOF5
<Tape and Reel information>
1.6 0.05
1.0 0.05
Tape
Embossed carrier tape
3000pcs
5
4
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1pin
1
2
3
0.13 0.05
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
0.22 0.05
0.5
Reel
(Unit : mm)
∗
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.11 - Rev.C
11/11
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
BU4234 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
BU4234F | ROHM | Low Voltage Detector IC with Adjustable Output Delay | 获取价格 | |
BU4234F-TR | ROHM | Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series | 获取价格 | |
BU4234FVE | ROHM | Low Voltage Detector IC with Adjustable Output Delay | 获取价格 | |
BU4234FVE-TR | ROHM | Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series | 获取价格 | |
BU4234G | ROHM | Low Voltage Detector IC with Adjustable Output Delay | 获取价格 | |
BU4234G-TR | ROHM | Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series | 获取价格 | |
BU4235 | ROHM | Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series | 获取价格 | |
BU4235F | ROHM | Low Voltage Detector IC with Adjustable Output Delay | 获取价格 | |
BU4235F-TR | ROHM | Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series | 获取价格 | |
BU4235FVE | ROHM | Low Voltage Detector IC with Adjustable Output Delay | 获取价格 |
BU4234 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6