BU4929 [ROHM]
Low Voltage Standard CMOS Voltage Detector IC Series; 低电压标准CMOS电压检测器IC系列型号: | BU4929 |
厂家: | ROHM |
描述: | Low Voltage Standard CMOS Voltage Detector IC Series |
文件: | 总9页 (文件大小:260K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Voltage Detector IC Series
Low Voltage Standard
CMOS Voltage Detector IC Series
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
No.09006ECT01
Description
ROHM standard CMOS reset IC series is a high-accuracy low current consumption reset IC series.
The lineup was established with two output types (Nch open drain and CMOS output) and detection voltage range from
0.9V to 4.8V in increments of 0.1V, so that the series may be selected according to the application at hand.
Features
1) Detection voltage from 0.9V to 4.8V in 0.1V increments
2) Highly accurate detection voltage: ±1.0%
3) Ultra-low current consumption
4) Nch open drain output (BU48□□G/F/FVE)and CMOS output (BU49□□G/F/FVE)
5) Small surface package
SSOP5: BU48□□G,BU49□□G
SOP4: BU48□□F,BU49□□F
VSOF5: BU48□□FVE,BU49□□FVE
Applications
All electronics devices that use microcontrollers and logic circuits.
Selection Guide
No.
Specifications
Description
1
Output Circuit Format
Detection Voltage
Package
8:Open Drain Output, 9:CMOS Output
Example VDET: Represented as 0.1V steps in the
range from 0.9V to 4.8V
Part Number : BU4
2
1
2
3
(Displayed as 0.9 in the case of 0.9V)
G:SSOP5(SMP5C2)/ F:SOP4/ FVE:VSOF5(EMP5)
3
Lineup
Detection
voltage
4.8V
4.7V
4.6V
4.5V
4.4V
4.3V
4.2V
4.1V
4.0V
3.9V
3.8V
3.7V
3.6V
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
Part
Detection
Part
Detection
Part
Detection
voltage
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
1.1V
1.0V
0.9V
Part
Making
Making
Making
Making
Number
BU4848
BU4847
BU4846
BU4845
BU4844
BU4843
BU4842
BU4841
BU4840
BU4839
BU4838
BU4837
BU4836
BU4835
BU4834
BU4833
BU4832
BU4831
BU4830
BU4829
voltage
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
1.1V
1.0V
0.9V
Number
voltage
4.8V
4.7V
4.6V
4.5V
4.4V
4.3V
4.2V
4.1V
4.0V
3.9V
3.8V
3.7V
3.6V
3.5V
3.4V
3.3V
3.2V
3.1V
3.0V
2.9V
Number
Number
JR
JQ
JP
JN
JM
JL
JK
JJ
JH
JG
JF
JE
JD
JO
JB
JA
HZ
HY
HX
HW
HV
HU
HT
HS
HR
HQ
HP
HN
HM
HL
BU4828
BU4827
BU4826
BU4825
BU4824
BU4823
BU4822
BU4821
BU4820
BU4819
BU4818
BU4817
BU4816
BU4815
BU4814
BU4813
BU4812
BU4811
BU4810
BU4809
LH
LG
LF
BU4948
BU4947
BU4946
BU4945
BU4944
BU4943
BU4942
BU4941
BU4940
BU4939
BU4938
BU4937
BU4936
BU4935
BU4934
BU4933
BU4932
BU4931
BU4930
BU4929
KM
KL
KK
KJ
KH
KG
KF
KE
KD
KC
KB
KA
JZ
JY
JX
JW
JV
JU
JT
JS
BU4928
BU4927
BU4926
BU4925
BU4924
BU4923
BU4922
BU4921
BU4920
BU4919
BU4918
BU4917
BU4916
BU4915
BU4914
BU4913
BU4912
BU4911
BU4910
BU4909
LE
LD
LC
LB
LA
KZ
KY
KX
KW
KV
KU
KT
KS
KR
KQ
KP
KN
HK
HJ
HH
HG
HF
HE
HD
HC
HB
HA
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.06 - Rev.C
1/8
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Absolute maximum ratings (Ta=25°C)
Parameter
Power Supply Voltage
Symbol
Limits
-0.3 ~ +7
Unit
V
VDD-GND
Nch Open Drain Output
CMOS Output
GND-0.3 ~ +7
GND-0.3 ~ VDD+0.3
540
Output Voltage
VOUT
V
*1*4
SSOP5
SOP4
Power
*2*4
*3*4
Pd
400
mW
Dissipation
VSOF5
210
Operating Temperature
Topr
Tstg
-40 ~ +125
-55 ~ +125
°C
°C
Ambient Storage Temperature
*1 When used at temperatures higher than Ta=25°C, the power is reduced by 5.4mW per 1°C above 25°C.
*2 When used at temperatures higher than Ta=25°C, the power is reduced by 4.0mW per 1°C above 25°C.
*3 When used at temperatures higher than Ta=25°C, the power is reduced by 2.1mW per 1°C above 25°C.
*4 When a ROHM standard circuit board (70mm×70mm×1.6mm, glass epoxy board)is mounted.
Electrical characteristics
Limit
Typ.
Parameter
Symbol
Condition
Unit
Min.
Max.
BU4848
BU4847
BU4846
BU4845
BU4844
BU4843
BU4842
BU4841
BU4840
BU4839
BU4838
BU4837
BU4836
BU4835
BU4834
BU4833
BU4832
BU4831
BU4830
BU4829
BU4828
BU4827
BU4826
BU4825
BU4824
BU4823
BU4822
BU4821
BU4820
BU4819
BU4818
BU4817
BU4816
BU4815
BU4814
BU4813
BU4812
BU4811
BU4810
BU4809
4.752
4.653
4.554
4.455
4.356
4.257
4.158
4.059
3.960
3.861
3.762
3.663
3.564
3.465
3.366
3.267
3.168
3.069
2.970
2.871
2.772
2.673
2.574
2.475
2.376
2.277
2.178
2.079
1.980
1.881
1.782
1.683
1.584
1.485
1.386
1.287
1.188
1.089
0.990
0.891
4.800
4.700
4.600
4.500
4.400
4.300
4.200
4.100
4.000
3.900
3.800
3.700
3.600
3.500
3.400
3.300
3.200
3.100
3.000
2.900
2.800
2.700
2.600
2.500
2.400
2.300
2.200
2.100
2.000
1.900
1.800
1.700
1.600
1.500
1.400
1.300
1.200
1.100
1.000
0.900
4.848
4.747
4.646
4.545
4.444
4.343
4.242
4.141
4.040
3.939
3.838
3.737
3.636
3.535
3.434
3.333
3.232
3.131
3.030
VDD=HL , Ta=25°C
RL=470kΩ
2.929
2.828
Detection Voltage
VDET
V
2.727
2.626
2.525
2.424
2.323
2.222
2.121
2.020
1.919
1.818
1.717
1.616
1.515
1.414
1.313
1.212
1.111
1.010
0.909
Detection Voltage
Temperature Coefficient
*1
VDET/∆T Ta=-40°C~125°C
VDD=LHL
-
±30
-
ppm/°C
V
VDET
×0.03
VDET
×0.03
VDET
×0.05
VDET
×0.05
VDET
×0.08
VDET
×0.07
VDET≤1.0V
VDET≥1.1V
Hysteresis Voltage
∆VDET
Ta=-40°C~125°C
RL=470kΩ
*1 Designed Guarantee.(Outgoing inspection is not done on all products.)
*This product is not designed for protection against radioactive rays.
www.rohm.com
2009.06 - Rev.C
2/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Electrical characteristics (Unless Otherwise Specified Ta=-25 to 125°C)
Limit
Parameter
Symbol
Condition
Unit
Min.
Typ.
0.15
0.20
0.25
0.30
0.35
0.40
0.30
0.35
0.40
0.45
0.50
0.55
-
Max.
VDET =0.9-1.3V
-
0.88
1.05
VDET =1.4-2.1V
VDET =2.2-2.7V
VDET =2.8-3.3V
VDET =3.4-4.2V
VDET =4.3-4.8V
VDET =0.9-1.3V
VDET =1.4-2.1V
VDET =2.2-2.7V
VDET =2.8-3.3V
VDET =3.4-4.2V
VDET =4.3-4.8V
-
-
1.23
µA
Circuit Current when ON
IDD1
VDD=VDET-0.2V
VDD=VDET+2.0V
-
1.40
-
-
1.58
1.75
1.40
1.58
-
-
-
1.75
µA
Circuit Current when OFF
IDD2
-
1.93
-
2.10
2.28
-
VOL≤0.4V, Ta=25~125°C, RL=470kΩ
VOL≤0.4V, Ta=-40~25°C, RL=470kΩ
VDS=0.05V VDD=0.85V
0.70
0.90
20
1.0
4.0
1.7
2.0
-
Operating Voltage Range
‘Low’ Output Current (Nch)
VOPL
IOL
V
-
-
100
3.3
-
-
-
-
-
µA
VDS=0.5V VDD=1.5V VDET=1.7-4.8V
VDS=0.5V VDD=2.4V VDET=2.7-4.8V
VDS=0.5V VDD=4.8V VDET=0.9-3.9V
VDS=0.5V VDD=6.0V VDET=4.0-4.8V
VDD=VDS=7V
mA
7.2
‘High’ Output Current (Pch)
3.4
IOH
mA
µA
(only BU49□□G/F/FVE)
4.0
Output Leak Current when
OFF
-
-
0
0
0.1
1
Ta=-40°C~85°C
Ileak
VDD=VDS=7V
(only BU48□□G/F/FVE)
Ta=85°C~125°C
* This product is not designed for protection against radioactive rays.
Block Diagrams
BU48□□G/F/FVE
BU49□□G/F/FVE
VDD
VDD
VOUT
VOUT
Vref
Vref
GND
GND
Fig.1
Fig.2
TOP VIEW
TOP VIEW
TOP VIEW
SSOP5
SOP4
VSOF5
PIN No.
Symbol
Function
PIN No.
Symbol
VOUT
VDD
Function
Reset output
PIN No. Symbol
Function
1
2
3
4
5
VOUT Reset output
1
2
3
4
1
2
3
4
5
VOUT
SUB
N.C.
Reset output
Substrate*
VDD
GND
N.C.
N.C.
Power supply voltage
Power supply voltage
Unconnected terminal
GND
GND
N.C.
Unconnected terminal
Power supply voltage
GND
Unconnected terminal
Unconnected terminal
GND
VDD
GND
*Connect the substrate to VDD
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.06 - Rev.C
3/8
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Reference Data (Unless specified otherwise, Ta=25°C)
0.6
0.5
0.4
0.3
0.2
0.1
0.0
5
4
3
2
1
0
25
20
15
10
5
BU4916F
】
BU4816F
】
【
BU4816F
【
】
【
VDD=6.0V
VDD=4.8V
VDD=1.2V
0
0
1
2
3
4
5
6
7
0.0
0.5
1.0
1.5
2.0
2.5
0
1
2
3
4
5
6
DRAIN-SOURCE VOLTAGE
VDS[V]
:
V
DD SUPPLY VOLTAGE VDD[V]
:
DRAIN-SOURCE VOLTAGE VDS[V]
:
Fig.3 Circuit Current
Fig.4 “LOW” Output Current
Fig.5 “High” Output Current
7
6
5
4
3
2
1
0
1.0
0.8
0.6
0.4
0.2
0.0
2.0
1.5
1.0
BU4816F
【
】
BU4816F
【
】
Low to high(VDET+ΔVDET
)
High to low(VDET)
BU4816F
0
【
】
0.0
0.5
1.0
1.5
2.0
2.5
-40
40
80
120
0
1
2
3
4
5
6
7
VDD SUPPLY VOLTAGE VDD[V]
:
TEMPERATURE Ta[ ]
: ℃
V
DD SUPPLY VOLTAGE VDD[V]
:
Fig.7 Operating Limit Voltage
Fig.6 I/O Characteristics
Fig.8 Detecting Voltage
Release Voltage
0.5
1.0
1.0
0.8
0.6
0.4
0.2
0.0
BU4816F
BU4816F
【
】
BU4816F
【
【
】
】
0.4
0.3
0.2
0.1
0.0
0.8
0.6
0.4
0.2
0.0
-40
0
40
80
120
-40
0
40
80
120
-40
0
40
80
120
TEMPERATURE Ta[
]
℃
:
TEMPERATURE Ta[
]
℃
:
TEMPERATURE Ta[
]
℃
:
Fig.9 Circuit Current when ON
Fig.10 Circuit Current when OFF
Fig.11 Operating Limit Voltage
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.06 - Rev.C
4/8
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Reference Data
Examples of Output rising value(TPLH)and Output falling value(TPHL)
Part Number
BU4845G/F/FVE
BU4945G/F/FVE
TPLH[µs]
23.3
TPHL[µs]
275.9
3.5
354.3
VDD=4.3V5.1V
VDD=5.1V4.3V
* This data is for reference only.
This figure will vary with the application, so please confirm actual operation conditions before use.
Explanation of Operation
For both the open drain type(Fig.12)and the CMOS output type(Fig.13), the detection and release voltages are
used as threshold voltages. When the voltage applied to the VDD pins reaches the applicable threshold voltage, the Vout
terminal voltage switches from either “High” to “Low” or from “Low” to “High”. Because the BU48□□G/F/FVE series uses an
open drain output type, it is possible to connect a pull-up resistor to VDD or another power supply [The output “High” voltage
(VOUT) in this case becomes VDD or the voltage of the other power supply].
VDD
V
DD
VDD
R1
R2
R1
R2
Q2
Q1
RL
Vref
Vref
RESET
OUT
V
VOUT RESET
Q1
R3
R3
GND
GND
Fig.12 (BU48□□ type internal block diagram)
Fig.13 (BU49□□ type internal block diagram)
Timing Waveforms
Example:The following shows the relationship between the input voltage VDD, the CT Terminal Voltage VCT and the output
voltage VOUT when the input power supply voltage VDD is made to sweep up and sweep down (The circuits are those in
Fig.12 and 13).
1
When the power supply is turned on, the output is unsettled
from after over the operating limit voltage (VOPL) until TPHL.
DD
V
Therefore it is possible that the reset signal is not outputted
when the rise time of VDD is faster than TPHL.
VDET+ΔVDET
⑤
VDET
2
When VDD is greater than VOPL but less than the reset release
VOPL
0V
voltage (VDET + VDET), output (VOUT) voltages will switch to L.
3
If VDD exceeds the reset release voltage (VDET + VDET), then
OUT
V
VOUT switches from L to H (with a delay of TPLH).
VOH
4
If VDD drops below the detection voltage (VDET) when the
TPLH
TPHL
PLH
T
power supply is powered down or when there is a power supply
fluctuation, VOUT switches to L (with a delay of TPHL).
TPHL
VOL
5
The potential deference between the detection voltage and
①
②
③
④
the release voltage is known as the hysteresis width (VDET). The
system is designed such that the output does not flip-flop with
power supply fluctuations within this hysteresis width, preventing
malfunctions due to noise.
Fig.14
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.06 - Rev.C
5/8
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Circuit Applications
1) Examples of a common power supply detection reset circuit
VDD1
VDD2
Application examples of BU48□□G/F/FVE series
(Open Drain output type) and BU49□□G/F/FVE series
RL
(CMOS output type) are shown below.
Microcontroller
RST
BU48□□□
CASE1:The power supply of the microcontroller (VDD2) differs
from the power supply of the reset detection (VDD1).
Use the Open Drain Output Type (BU48□□G/FVE)
attached a load resistance (RL) between the output and
VDD2. (As shown Fig.15)
CIN
CL
(Capac itor for
noise filtering)
GND
CASE2:The power supply of the microcontroller (VDD1) is same
as the power supply of the reset detection (VDD1).
Use CMOS output type (BU43□□G/FVE) or Open Drain
Output Type (BU48□□G/FVE) attached a load
resistance (RL) between the output and VDD1.
(As shown Fig.16)
Fig.15 Open collector Output type
VDD1
Microcontroller
RST
BU49□□□
When a capacitance CL for noise filtering or setting the
output delay time is connected to the Vout pin (the reset
signal input terminal of the microcontroller), please take
into account the waveform of the rise and fall of the
output voltage (Vout).
CIN
CL
(Capacitor for
nois e filtering)
GND
Fig.16 CMOS Output type
2) Examples of the power supply with resistor dividers
In applications where the power supply input terminal (VDD) of an IC with resistor dividers, it is possible that a
through-current will momentarily flow into the circuit when the output logic switches, resulting in malfunctions (such as
output oscillatory state).
(Through-current is a current that momentarily flows from the power supply (VDD) to ground (GND) when the output level
switches from “High” to “Low” or vice versa.)
Consider the use of BD48□□ when the power supply input it with resistor dividers.
V1
R2
I1
VDD
CIN
BU48□□
BU49□□
R1
VOUT
CL
GND
Fig.17
www.rohm.com
2009.06 - Rev.C
6/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Operation Notes
1 . Absolute maximum range
Absolute Maximum Ratings are those values beyond which the life of a device may be destroyed. We cannot be defined the
failure mode, such as short mode or open mode. Therefore a physical security countermeasure, like fuse, is to be given
when a specific mode to be beyond absolute maximum ratings is considered.
2 . GND potential
GND terminal should be a lowest voltage potential every state.
Please make sure all pins that are over ground even if include transient feature.
3 . Electrical Characteristics
Be sure to check the electrical characteristics, that are one the tentative specification will be changed by temperature,
supply voltage, and external circuit.
4 . Bypass Capacitor for Noise Rejection
Please put into the to reject noise between VDD pin and GND with 1uF over and between VOUT pin and GND with 1000pF.
If extremely big capacitor is used, transient response might be late. Please confirm sufficiently for the point.
5 . Short Circuit between Terminal and Soldering
Don’t short-circuit between Output pin and VDD pin, Output pin and GND pin, or VDD pin and GND pin. When soldering the
IC on circuit board please is unusually cautious about the orientation and the position of the IC. When the orientation is
mistaken the IC may be destroyed.
6 . Electromagnetic Field
Mal-function may happen when the device is used in the strong electromagnetic field.
7 . The VDD line inpedance might cause oscillation because of the detection current.
8 . A VDD -GND capacitor (as close connection as possible) should be used in high VDD line impedance condition.
9 . Lower than the mininum input voltage makes the VOUT high impedance, and it must be VDD in pull up (VDD) condition.
10. Recommended value of RL Resistar is over 10kΩ (VDET=1.5V~4.8V),
over 100kΩ (VDET=0.9~1.4V).
11. This IC has extremely high impedance terminals. Small leak current due to the uncleanness of PCB surface might cause
unexpected operations. Application values in these conditions should be selected carefully. If 10MΩ leakage is assumed
between the CT terminal and the GND terminal, 1MΩ connection between the CT terminal and the VDD terminal would be
recommended. Also, if the leakage is assumed between the VOUT terminal and the GND terminal, the pull up resistor
should be less than 1/10 of the assumed leak resistance.
12. External parameters
For RL, the recommended range is 10kΩ~1MΩ. There are many factors (board layout, etc) that can affect characteristics.
Please verify and confirm using practical applications.
13. Power on reset operation
Please note that the power on reset output varies with the Vcc rise up time. Please verify the actual operation.
14. Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC. Therefore, be
certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
15. When the power supply, is turned on because of incertain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
www.rohm.com
2009.06 - Rev.C
7/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU48□□G, BU48□□F, BU48□□FVE, BU49□□G, BU49□□F, BU49□□FVE series
Part Number Selection
B
U
4
8
0
9
G
-
T
R
BU48: Standard CMOS reset IC
Open drain type
Detection voltage
09: 0.9V (0.1V step)
48: 4.8V
Package
Taping Specifications
Embossed Taping
G: SSOP5
F: SOP4
BU49: Standard CMOS reset IC
CMOS Output type
FVE: VSOF5
SSOP5
<Tape and Reel information>
°
°
+
−4
2.9 0.2
6
°
4
Tape
Embossed carrier tape
3000pcs
5
4
Quantity
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
3
1pin
+0.05
0.13
−0.03
+0.05
−0.04
0.42
0.1
0.95
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
Reel
(Unit : mm)
∗
SOP4
<Tape and Reel information>
2.0 0.2
Tape
Embossed carrier tape
°
°
+6
–4
1.3
3
°
4
Quantity
3000pcs
4
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
2
0.05
+0.05
–0.03
0.13
1pin
S
+0.05
–0.04
0.42
0.1
S
+0.05
–0.04
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
0.32
Reel
(Unit : mm)
∗
VSOF5
<Tape and Reel information>
1.6 0.05
1.0 0.05
Tape
Embossed carrier tape
5
4
Quantity
3000pcs
TR
Direction
of feed
The direction is the 1pin of product is at the upper right when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1pin
1
2
3
0.13 0.05
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
0.22 0.05
0.5
Reel
(Unit : mm)
∗
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.06 - Rev.C
8/8
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
相关型号:
©2020 ICPDF网 联系我们和版权申明