BU8317KV-E2 [ROHM]
Telephone Circuit, CMOS, PQFP80,;
| 型号： | BU8317KV-E2 |
| 厂家： | 
ROHM |
| 描述： | Telephone Circuit, CMOS, PQFP80, |
| 文件： | 总14页 (文件大小：230K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Communication ICs
Panel interface for telephones
BU8317KV
The BU8317KV is a large-scale integrated circuit which enables a serial input / output interface between the key input
required for panel boards used in PHS systems, portable telephones, and telephone answering machines and LED and
LCD control functions. It reduces the number of wiring harnesses needed between the main board in the telephone and
the panel board, and takes some of the processing load off the main CPU.
FApplications
PHS systems, portable telephones, telephone answering machines
FFeatures
1) 7 7 keypad matrix interface.
2) 12-bit LED driver. (6 bits can also function as input
pins)
4) Standby mode.
5) VQFP80 package.
3) 4-column32-segmentLCDdriver. (internalbias-gen-
erating resistor)
FAbsolute maximum ratings (unless otherwise noted, Ta = 25_C)
FRecommended operating conditions (Ta = 25_C)
295
Communication ICs
BU8317KV
FBlock diagram
FPin descriptions
296
Communication ICs
BU8317KV
297
Communication ICs
BU8317KV
FInput / output circuits
298
Communication ICs
BU8317KV
FElectrical characteristics (unless otherwise noted, Ta = 25_C, VDD=2.7 to 5.5V)
299
Communication ICs
BU8317KV
FTiming charts
300
Communication ICs
BU8317KV
FMeasurement circuits
301
Communication ICs
BU8317KV
FData formats (Serial data is input and output with the MSB coming first.)
(1) Reading data
SR
: Outputs SR pin status. Pressing a key (low level) outputs “1” and
releasing the key (high level) outputs “0”.
A “0” is output is the key is not pressed on low level.
R1XR7, C1XC7
L7XL12
: Outputs key data. Pressing a key outputs “1” and not pressing the
key outputs “0”, when on low level.
: Outputs parallel input data. Output “1” when the pin is on high lev-
el and “0” when it is on low level.
(2) LED resitor writing command
L1XL12
:
Used for LED control. LED lights up with “1” and is unlit with “0”.
(3) LCD register writing command
LC01XLC04
: Selects LCD common. “1” means select and “0” means do not se-
lect.
Segment control is active on the selected common, only.
Multiple commons can be selected simultaneously.
: Used for LCD segment control. Lights up with “1” and is unlit with
“0”.
LS01XLS32
302
Communication ICs
BU8317KV
(4) All LEDs, LCDs activate command
Used to clear non-active status of all LEDs and LCDs.
(5) All LEDs, LCDs non-active command
Temporarily turns off all LEDs and LCDs, while holding the LED and LCD register settings as they are.
LCD output changes to low level and the bias current channel is cut.
(6) Register reset command
Resets all LED and LCD resisters to “0”.
Clears stand-by mode.
Non-active status of all LEDs and LCDs changes to active status.
303
Communication ICs
BU8317KV
FRecommended method for inputting / outputting data
(1) Control command serial input
(2) Key data serial output
304
Communication ICs
BU8317KV
FStandby mode
(1) Setting the standby mode
S The standby mode is set by setting RE to L and WE to L.
S Oscillation stops and the line current falls to an extremely low level.
S The contents of the LED and LCD registers are reset (all data cleared to 0), and all LEDs and LCDs are
turned off.
S The LCD output goes LOW, and the bias current channel is cut off.
S The only effective key input is the SR key; no input is accepted from the keypad.
(2) Cancelling the standby mode
S The standby mode is cancelled by executing the register reset command.
S Setting SR to LOW in any state other than RE = LOW and WE = LOW immediately cancels the standby
mode.
S Setting SR to LOW when RE = LOW and WE = LOW initiates oscillation but does not cancel the standby
mode. Setting SR to HIGH stops oscillation once again.(If “on debounce” is valid for the SR key and KD
has output a LOW level, oscillation continues until an “off debounce” becomes valid.)
Standby mode setting example
1
2
3
At RE = LOW, WE = LOW, the standby mode is set, and oscillation stops.
In standby mode, no input is accepted.
Setting the SR pin to LOW initiates oscillation even in the standby mode.
(SR = LOW takes priority over RE = LOW, WE = LOW.)
4
When the SR pin is open (HIGH), RE = LOW and WE = LOW, so oscillation stops and the standby mode continues
to be effective.
5
6
Setting the SR pin LOW initiates oscillation even in the standby mode.
When RE = LOW, WE = LOW is no longer true, the standby mode is cancelled, and oscillation continues even if the
SR pin is open (HIGH).
7
Data is set in the output serial register at the falling edge of RE and when SR = LOW, and can be read.
305
Communication ICs
BU8317KV
FOscillation frequencies
FLCD drive wave forms
This is a time-shared drive system in
which 1 / 3 bias and 1 / 4 duty alternate
between two frames.
The figure at the right shows the drive
wave forms for the following conditions :
LC01-LSxx : Lighted
LC02-LSxx : Not lighted
LC03-LSxx : Lighted
LC04-LSxx : Not lighted
306
Communication ICs
BU8317KV
FConfiguring a booster circuit
This shows an example of booster circuit configuration for a VLCD pin, using the CPC and CPCB pins.
FConfiguring an LCD bias correction circuit
This shows an example of correction circuit configuration for the LCD output voltage, using the V3 pin.
307
Communication ICs
BU8317KV
FPrecautions when turning on the power supply
The power supply should be turned on when RE = LOW and WE = LOW, and the registers should then be reset using
the register reset command.
FPrecautions concerning data input and output
(1) Serial output of key data when several keys are
pressed at the same time is as shown at the right.
The key data when 1. and (1) are pressed at the
same time is the same as the key data when 2. and
3. are pressed at the same time.
(2) If the LED and LCD registers are rewritten, all of the bits should be written, and not just the pertinent bits.
FElectrical characteristic curve
FExternal dimensions (Units: mm)
308
相关型号：
©2020 ICPDF网 联系我们和版权申明