LM4565FVM_技术文档

Datasheet

Operational Amplifiers

Low Noise Operational Amplifier

LM4565F

●Key Specifications

●General Description

 Wide Operating Voltage:

 Wide Temperature Range:

 High voltage gain (RL=2kΩ):

 High Slew Rate:

 Wide Unity Gain Bandwidth:

 Low Input Noise Voltage:

±4V to ±18V

-40°C to +85°C

100dB(Typ.)

BA4565 is dual operational amplifier with high gain and

wide bandwidth. It has good performance of input

referred noise voltage(5_nV/

) and total harmonic

Hz

5.0V/μs (Typ.)

distortion(0.002%). These are suitable for Audio

applications.

10MHz (Typ.)

0.6µVrms (Typ.)

●Features

●Package

SOP8

W(Typ.) xD(Typ.) xH(Max.)

5.00mm x 6.20mm x 1.71mm

 Wide Operating Voltage

 High Voltage Gain

 Low distortion

 Wide Bandwidth

 High Slew Rate

 Low Noise Voltage

 Internal ESD protection

●Application

 Audio application

 General Purpose

●Block Diagram

VCC

IN

－

OUT

VOUT

IN

＋

VEE

Figure1. Simplified Schematic (1 channel only)

○Product structure：Silicon monolithic integrated circuit ○This product is not designed to be protected against radioactive rays.

www.rohm.com

TSZ22111･14･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

1/17

Datasheet

LM4565F

●Pin Configuration

SOP8

Pin No.

Symbol

OUT1

-IN1

1

2

3

4

5

6

7

8

OUT1

-IN1

+IN1

VEE

VCC

OUT2

-IN2

+IN2

1

2

3

4

8

7

6

5

CH1

- +

+IN1

VEE

CH2

+ -

+IN2

-IN2

OUT2

VCC

●Ordering Information

L M 4

5

6

5 F

-

E2

Part Number

LM4565F

Package

F:SOP8

Packaging and forming specification

E2: Embossed tape and reel

(SOP8)

●Line-up

Topr

Package

Reel of 2500

Operable Part Number

LM4565F-E2

-40°C to +85°C

SOP8

●Absolute Maximum Ratings(Ta=25°C)

Parameter

Symbol

Ratings

Unit

Supply Voltage

VCC - VEE

+36

690^*1*2

+36

V

mW

V

Power Dissipation

Differential Input Voltage^*3

Pd

Vid

Input Common-mode

Voltage Range

Vicm

(VEE - 0.3) to (VEE + 36)

V

Operating Voltage

Vopr

Topr

Tstg

±4 to ±18

- 40 to +85

- 55 to +150

V

Operating Temperature

Storage Temperature

°C

Maximum

Junction Temperature

Tjmax

+150

°C

Note: Absolute maximum rating of each item indicates the condition which must not be exceeded.

Application of voltage in excess of absolute maximum rating or usage out of absolute maximum rated

temperature environment may cause deterioration of characteristics.

*1

*2

*3

When used at temperature above Ta＝25°C, reduce by 5.52mW/°C.

Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm).

The differential input voltage is the voltage difference between inverting input and non-inverting input.

Input terminal voltage is set to more than VEE.

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

2/17

Datasheet

LM4565F

●Electrical Characteristics:

○LM4565F (Unless otherwise specified VCC = +15V, VEE = -15V)

Limits

Typ.

Temperature

Parameter

Symbol

Unit

Condition

Range

Min.

-

Max.

1.5

Input Offset Voltage ^*4*5

Input Offset Current ^*4

Input Bias Current ^*4

Vio

Iio

Ib

25°C

0.5

2

mV

nA

RS ≤10kΩ

25°C

-

50

-

70

250

25°C

-

4.5

-

7

RL=∞, All Op-Amps,

VIN+=0V

Supply Current^*5

ICC

Av

mA

Full range

25°C

-

8.5

Large Signal Voltage Gain

Maximum Output Voltage

86

±12

±11

±12

-

100

±14

±12.5

±14

130

-

dB

V

RL ≥2kΩ, OUT =±10V

25°C

RL ≥2kΩ

Io≥25mA

-

VOM

25°C

V

Input Common-mode Voltage Range

Output Source Current^*6

Vicm

IOH

25°C

V

VIN+=1V, VIN-=0V

OUT=-15V,

1CH is short circuit

VIN+=0V,VIN-=1V

OUT=+15V,

25°C

mA

dB

Output Sink Current^*6

Common-mode Rejection Ratio

Power Supply Rejection Ratio

Slew Rate

IOL

CMRR

PSRR

SR

25°C

-

160

100

5

-

1CH is short circuit

80

82

-

RL ≤10kΩ

V/μs RL=2kΩ, CL=100pF

MHz RL=2kΩ

Unity Gain Frequency

Gain Band Width

f_T

4

GBW

θ

-

10

-

MHz RL=2kΩ, f=100kHz

Phase Margin

40

deg

µVrms

nV/ Hz

%

RL=2kΩ

RIAA, RS=100Ω

DIN-AUDIO

0.6

5

Equivalent Input Noise Voltage

Vn

25°C

Vicm=0V, f=1kHz

Av=20dB,

OUT=0.1Vrms,

f=1kHz

Total Harmonic Distortion+ Noise

Channel Separation

THD+N

CS

25°C

0.002

110

Av=40dB, RS=1kΩ

f=1kHz

dB

*4

*5

*6

Absolute value.

Full range: Ta=-40°C to +85°C

Please consider the power dissipation when selecting the output current.

When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

3/17

Datasheet

LM4565F

Description of electrical characteristics

Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.

Note that item name, symbol and their meaning may differ from those on other manufacturer’s document or general

documents.

1. Absolute maximum ratings

Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute

maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.

1.1 Supply voltage (VCC - VEE)

Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power

supply terminal without deterioration or destruction of characteristics of internal circuit.

1.2 Differential input voltage (Vid)

Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without

deterioration and destruction of characteristics of IC.

1.3 Input common-mode voltage range (Vicm)

Indicates the maximum voltage that can be applied to the non-inverting terminal and inverting terminal without

deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assures

normal operation of IC. When normal Operation of IC is desired, the input common-mode voltage of characteristics

item must be followed.

1.4 Power dissipation (Pd)

Indicates the power that can be consumed by the IC when mounted on a specific board at ambient temperature 25°C(normal

temperature). As for packaged product, Pd is determined by the temperature that can be permitted by the IC in the

package (maximum junction temperature) and the thermal resistance of the package.

2. Electrical characteristics item

2.1 Input offset voltage (Vio)

Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the

input voltage difference required for setting the output voltage to 0 V.

2.2 Input offset current (Iio)

Indicates the difference of input bias current between non-inverting terminal and inverting terminal.

2.3 Input bias current (Ib)

Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at

the non-inverting and inverting terminals.

2.4 Supply current (ICC)

Indicates the current that flows within the IC under specified no-load conditions.

2.5 Large signal voltage gain (Av)

Indicates the amplification rate (gain) of output voltage against the voltage difference between non-inverting terminal

and inverting terminal. It is normally the amplification rate (gain) with reference to DC voltage.

Av = (Output voltage fluctuation) / (Input offset fluctuation)

2.6 Output saturation voltage (VOM)

Signifies the voltage range that can be output under specific output conditions.

2.7 Input common-mode voltage range (Vicm)

Indicates the input voltage range where IC operates normally.

2.8 Common-mode rejection ratio (CMRR)

Indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. It is

normally the fluctuation of DC.

CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)

2.9 Power supply rejection ratio (PSRR)

Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of

DC. PSRR= (Change of power supply voltage)/(Input offset fluctuation)

2.10 Slew rate (SR)

Indicates the ratio of the change in output voltage with time when a step input signal is applied.

2.11 Unity Gain Frequency (f_T)

Indicates a frequency where the voltage gain of Op-Amp is 1.

2.12 Gain Bandwidth (GBW)

The product of the open-loop voltage gain and the frequency at which the voltage gain decreases 6dB/octave.

2.13 Phase Margin (θ)

Indicates the margin of phase from 180 degree phase lag at unity gain frequency.

2.14 Equivalent input noise voltage (Vn)

Indicates a noise voltage generated inside the operational amplifier reflected back to an ideal voltage source

connected in series with input terminal.

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

4/17

Datasheet

LM4565F

2.15 Total Harmonic Distortion+ Noise (THD+N)

Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage

of driven channel.

2.16 Channel Separation (CS)

Indicates the fluctuation in the output voltage of the driven channel with reference to the change of output voltage of

the channel which is not driven.

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

5/17

Datasheet

LM4565F

●Typical Performance Curves

○LM4565F

800

600

400

200

0

8

7

6

5

4

3

2

1

0

-40°C

LM4565F

25°C

85°C

85

±0

±3

±6

±9

±12 ±15 ±18

0

25

50

75

100

SUPPLY VOLTAGE [V]

AMBIENT TEMPERATURE [

]

℃

Figure 2.

Figure 3.

Derating curve

Supply Current – Supply Voltage

8

7

6

5

4

3

2

1

0

20

15

10

5

0

-5

-10

-15

-20

0

5

10

15

20

-50

-25

0

25

50

75

100

SUPPLYVOLTAGE [V]

AMBIENT TEMPERATURE [°C]

Figure 5.

Figure 4.

Maximum Output Voltage – Supply Voltage

Supply Current – Ambient Temperature

(VCC/VEE = ±15V)

(RL=2kΩ, Ta=25°C)

(*)The data above is measurement value of typical sample, it is not guaranteed.

www.rohm.com

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

6/17

TSZ22111･15･001

Datasheet

LM4565F

●Typical Performance Curves (Reference data) – Continued

○LM4565F

20

15

10

5

20

15

10

5

0

-5

-10

-15

-20

-10

-15

-20

±0

±5

±10

±15

±20

-50 -25

0

25

50

75

100

SUPPLYVOLTAGE [V]

AMBIENT TEMPERATURE [°C]

Figure 7.

Figure 6.

Maximum Output Voltage – Supply Voltage

(Io=25mA, Ta=25°C)

Maximum Output Voltage – Ambient Temperature

(VCC/VEE = ±15V, RL=2KΩ)

20

15

10

5

3

2

1

0

-5

-1

-2

-3

-10

-15

-20

-50 -25

0

25

50

75

100

-50 -25

0

25

50

75 100

AMBIENT TEMPERATURE [°C]

Figure 9.

Figure 8.

Input Offset Voltage – Ambient Temperature

(VCC/VEE = ±15V)

Maximum Output Voltage – Ambient Temperature

(VCC/VEE = ±15V, Io=25mA)

(*)The data above is measurement value of typical sample, it is not guaranteed.

www.rohm.com

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

7/17

TSZ22111･15･001

Datasheet

LM4565F

●Typical Performance Curves (Reference data) – Continued

○LM4565F

3

2

150

125

100

75

1

-40°C

0

85°C

25°C

50

-1

-2

-3

25

0

-50

-25

0

25

50

75

100

-15

-10

-5

0

5

10

15

AMBIENT TEMPERATURE [°C]

INPUT COMMON MODE VOLTAGE [V]

Figure 11.

Figure 10.

Input Bias Current – Ambient Temperature

(VCC/VEE = ±15V)

Input Offset Voltage – Input Common mode Voltage

(VCC/VEE = ±15V)

130

140

130

120

110

100

90

120

110

100

90

80

70

80

-50 -25

0

25

50

75 100

-50 -25

0

25

50

75 100

AMBIENT TEMPERATURE [°C]

Figure 12.

Figure 13.

Large Signal Voltage Gain – Ambient Temperature

(VCC/VEE = ±15V, RL=2kΩ)

Common Mode Rejection Ratio – Ambient Temperature

(VCC/VEE = ±15V)

(*)The data above is measurement value of typical sample, it is not guaranteed.

www.rohm.com

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

8/17

TSZ22111･15･001

Datasheet

LM4565F

●Typical Performance Curves (Reference data) - Continued

○LM4565F

10

8

140

120

100

80

6

4

2

60

0

-50

-25

0

25

50

75

100

-50 -25

0

25

50

75 100

AMBIENT TEMPERATURE [°C]

Figure 14.

Figure 15.

Power Supply Rejection Ratio – Ambient Temperature

Slew Rate L-H – Ambient Temperature

(VCC/VEE = ±15V, RL=2kΩ, CL=100pF)

10

8

100

80

60

40

20

0

200

150

100

50

Phase

6

Gain

4

2

0

10²

10³

10⁴

10⁵

10⁶

10⁷

-50

-25

0

25

50

75

100

AMBIENT TEMPERATURE [°C]

FREQUENCY [Hz]

Figure 16.

Figure 17.

Slew Rate H-L – Ambient Temperature

(VCC/VEE = ±15V, RL=2kΩ, CL=100pF)

Voltage Gain・Phase – Frequency

(VCC/VEE = ±15V, RL=2kΩ)

(*)The data above is measurement value of typical sample, it is not guaranteed.

www.rohm.com

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

9/17

TSZ22111･15･001

Datasheet

LM4565F

●Typical Performance Curves (Reference data) - Continued

○LM4565F

30

25

20

15

10

5

1

0.1

0.01

0.001

20Hz

1kHz

20kHz

0.0001

0

0.01

0.1

1

10

100

10⁰

10¹

10²

10³

10⁴

10⁵

FREQUENCY[Hz]

OUTPUT VOLTAGE [Vrms]

Figure 18.

Figure 19.

Total Harmonic Distortion – Output Voltage

(VCC/VEE = ±15V, RL = 2kΩ, f = 1kHz)

Equivalent Input Noise Voltage – Frequency

(VCC/VEE=±15V, Ta = 25°C, Av = 40dB)

1

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0

±0

±5

±10

±15

±20

SUPPLY VOLTAGE [V]

Figure 20.

Equivalent Input Noise Voltage – Supply Voltage

(Ta = 25°C, DIN-AUDIO)

(*)The data above is measurement value of typical sample, it is not guaranteed.

www.rohm.com

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

10/17

TSZ22111･15･001

Datasheet

LM4565F

●Application Information

NULL method condition for Test Circuit 1

VCC, VEE, EK, Vicm Unit:V

Parameter

Calculation

VF

S1

S2

S3

VCC VEE

EK

0

Vicm

0

Input Offset Voltage

VF1

VF2

VF3

VF4

VF5

ON

OFF

15

-15

1

-10

10

Large Signal Voltage Gain

ON

15

-15

0

2

-10

10

Common-mode Rejection Ratio

(Input Common-mode Voltage Range)

ON

OFF

15

-15

0

3

4

VF6

VF7

4

-4

Power Supply Rejection Ratio

0

18

-18

－ Calculation－

|VF1|

Vio

Av

[V]

=

1. Input Offset Voltage (Vio)

1+RF/RS

ΔEK × (1+RF/RS)

2. Large Signal Voltage Gain (Av)

[dB]

= 20Log

|VF2-VF3|

3. Common-mode Rejection Ratio (CMRR)

4. Power Supply Rejection Ratio (PSRR)

ΔVicm × (1+RF/RS)

CMRR

PSRR

20Log

=

[dB]

|VF4 - VF5|

ΔVcc × (1+ RF/RS)

=

|VF6 - VF7|

0.1µF

RF=50kΩ

0.01µF

500kΩ

SW1

VCC

EK

15V

Vo

RS=50Ω

Ri=10kΩ

500kΩ

0.1µF

DUT

0.1µF

NULL

-15V

SW3

RL

1000pF

Ri=10kΩ

RS=50Ω

50kΩ

VF

Vicm

VRL

VEE

Figure21. Test circuit 1

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

11/17

Datasheet

LM4565F

Switch Condition for Test Circuit 2

SW No.

SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12

Supply Current

OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF

OFF ON OFF OFF ON OFF OFF ON OFF OFF ON OFF

OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF ON

ON OFF OFF ON ON OFF OFF OFF ON OFF OFF ON

Maximum Output Voltage RL=2kΩ

Slew Rate

Maximum Frequency

Input voltage

SW３

SW4

R2 100kΩ

VCC=30V

●

VH

VL

－

＋

SW1

R1

SW2

t

Input wave

SW5

SW8 SW9

SW10 SW11 SW12

SW6

SW7

Output voltage

VH

1kΩ

SR=ΔV/Δt

90%

RL

CL

VIN-

VIN+

Vo

ΔV

10%

VL

Δt

t

Figure 22. Test circuit2

Output wave

Figure 23 Slew rate input output wave

R2=100kΩ

VCC

R1=1kΩ

OUT1

V

～

OUT2

～

R1//R2

=1Vrms

R1//R2

VEE

VIN

100×OUT1

OUT2

CS=20Log

Figure 24. Test circuit 3 (Channel Separation)

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

12/17

Datasheet

LM4565F

Application example

○Voltage follower

Voltage gain is 0dB.

VCC

Using this circuit, the output voltage (OUT) is controlled

to be equal to the input voltage (IN). This circuit also

stabilizes OUT due to high input impedance and low

output impedance. Computation for OUT is shown

below.

OUT

OUT=IN

IN

VEE

Figure 25. Voltage follower

○Inverting amplifier

R2

For inverting amplifier, IN is amplified by a voltage gain

decided by the ratio of R1 and R2.The out-of-phase

output voltage is shown in the next expression.

OUT=-(R2/R1)・IN

VCC

R1

IN

This circuit has input impedance equal to R1.

OUT

R1//R2

VEE

Figure 26. Inverting amplifier circuit

○Non-inverting amplifier

For non-inverting amplifier, IN is amplified by a voltage

gain decided by the ratio of R1 and R2. OUT is in-phase

with Vin and is shown in the next expression.

OUT=(1+R2/R1)・IN

R1

R2

VCC

Effectively, this circuit has high input impedance since its

input side is the same as that of the operational

amplifier.

OUT

IN

VEE

Figure 27. Non-inverting amplifier circuit

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

13/17

Datasheet

LM4565F

●Power Dissipation

Power dissipation (total loss) indicates the power that the IC can consume at Ta=25°C (normal temperature). As the IC

consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable

temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and

consumable power.

Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the

thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the

maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold

resin or lead frame of the package. Thermal resistance, represented by the symbol θja°C/W, indicates this heat dissipation

capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance.

Figure 28(a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the

Thermal resistance (θja), given the ambient temperature (Ta), maximum junction temperature (Tjmax), and power

dissipation (Pd).

θja = (Tjmax－Ta) / Pd °C/W

・・・・・ (Ⅰ)

The Derating curve in Figure 28(b) indicates the power that the IC can consume with reference to ambient temperature.

Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal

resistance (θja), which depends on the chip size, power consumption, package, ambient temperature, package condition,

wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a

reference value measured at a specified condition. Figure 29(c) shows an example of the derating curve for LM4565.

LSI

[W]

n of LSI

の消費電力

Power dissipa

tio

Pd (max)

θja=(Tjmax-Ta)/Pd °C/W

P2

θja2 < θja1

θ' ja2

Ta[ °C]

Ambient temperature

P1

θ ja2

Tj ' (max) Tj (max)

θ' ja1

θ ja1

75

Tj[

]

Chip surface temperature

°C

0

25

50

100

125

150

Ambient temperature Ta [

]

℃

周囲温度

(a) Thermal resistance

(b) Derating curve

Figure 28. Thermal resistance and derating

800

600

400

200

0

LM4565F

0

25

50

75

100

AMBIENT TEMPERATURE [°C]

(c) LM4565

5.52

mW/°C

When using the unit above Ta=25°C, subtract the value above per °C. Permissible dissipation is the value

when FR4 glass epoxy board 70mm×70mm×1.6mm (cooper foil area below 3%) is mounted

Figure 29. Derating curve

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

14/17

Datasheet

LM4565F

VCC

●Operational Notes

1) Processing of unused circuit

+

-

It is recommended to apply the connection (see the Figure 30.) and set the

non-inverting input terminal at a potential within the input common-mode voltage

range (Vicm) for any unused circuit.

Connect

to Vicm

Vicm

2) Applied voltage to the input terminal

V^VE^EE^E

For normal circuit operation of voltage comparator, please input a voltage for its

input terminal within input common mode voltage. Then, regardless of

power supply voltage, (VEE) – 0.3V can be applied to input terminals without

deterioration or destruction of its characteristics.

Figure 30. The example of

application circuit for unused op-amp

3) Operating power supply (split power supply/single power supply)

The voltage comparator operates if a certain level of voltage is applied between

VCC and VEE. Therefore, the operational amplifier can be operated under

single power supply or split power supply.

4) Power dissipation (Pd)

If the IC is used under excessive power dissipation, an increase in the chip temperature will cause deterioration of the

electrical characteristics of the IC. As an example, reduction of current capability may happen. Take consideration of the

effective power dissipation and thermal design with a sufficient margin. Pd is reference to the provided power dissipation

curve.

5) Short circuits between pins and incorrect mounting

When mounting the IC on a printed circuit board, take notice of the direction and position of the IC. If IC is mounted

erroneously, it may be damaged. Also, when a foreign object is inserted between outputs, between output and VCC

terminal, or between output and VEE terminal, it causes short circuit which may damage the IC.

6) Usage under strong electromagnetic field

Be careful when using the IC under strong electromagnetic field because it may malfunction.

7) Usage of IC

When pressure is applied to the IC through warp on the printed circuit board, the characteristics may fluctuate due to

piezo effect. Be careful with the warp on the printed circuit board.

8) Testing IC on the application board

When testing IC on the application board, in cases where the capacitor is connected to low impedance, make sure to

discharge per process because there is a possibility that the IC may be damaged due to stress. When removing IC from

the application board, it is essential to cut supply voltage. As a countermeasure against the static electricity, observe

proper grounding during fabrication process and take due care when carrying and storing it.

9) The IC destruction caused by capacitive load

The IC may be damaged when VCC terminal and VEE terminal is shorted with the charged output terminal capacitor.

When IC is used as an operational amplifier or as an application circuit where oscillation is not activated by an output

capacitor, output capacitor must be kept below 0.1μF in order to prevent the damage mentioned above.

10) Decoupling capacitor

Insert the decoupling capacitor between VCC and VEE for stable operation of operational amplifier.

Status of this document

The Japanese version of this document is the formal specification. A customer may use this translation version only for

reference to help reading the formal version.

If there are any differences in the translated version of this document, the formal version takes priority.

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

15/17

Datasheet

LM4565F

●Physical Dimensions Tape and Reel Information

SOP8

5.0 0.2

(MAX 5.35 include BURR)

Tape

Embossed carrier tape

2500pcs

+

−

6

°

4°

4

°

Quantity

8

1

7

6

5

E2

Direction

of feed

The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand

(

)

2

3

4

0.595

+0.1

0.17

-

0.05

S

0.1

S

1.27

Direction of feed

1pin

0.42 0.1

Reel

Order quantity needs to be multiple of the minimum quantity.

(Unit : mm)

∗

●Marking Diagram

SOP8(TOP VIEW)

Part Number Marking

LOT Number

1PIN MARK

Product Name

LM4565

Package Type

SOP8

Marking

4565

F

●Land pattern data

all dimensions in mm

Land pitch

e

Land space

MIE

Land length

Land width

b2

PKG

≥ℓ2

SOP8

1.27

4.60

1.10

0.76

MIE

ℓ2

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

16/17

Datasheet

LM4565F

●Revision History

Date

Revision

001

Changes

30.NOV.2012

New Release

www.rohm.com

TSZ22111･15･001

TSZ02201-0RAR1G200590-1-2

30.NOV.2012 Rev.001

17/17

Daattaasshheeeett

Notice

●General Precaution

1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.

ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any

ROHM’s Products against warning, caution or note contained in this document.

2) All information contained in this document is current as of the issuing date and subject to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales

representative.

●Precaution on using ROHM Products

1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,

OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you

intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport

equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car

accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or

serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.

Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any

damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific

Applications.

2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3) Our Products are designed and manufactured for use under standard conditions and not under any special or

extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any

special or extraordinary environments or conditions. If you intend to use our Products under any special or

extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of

product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4) The Products are not subject to radiation-proof design.

5) Please verify and confirm characteristics of the final or mounted products in using the Products.

6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual

ambient temperature.

8) Confirm that operation temperature is within the specified range described in the product specification.

9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Notice - Rev.003

Daattaasshheeeett

●Precaution for Mounting / Circuit board design

1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the

ROHM representative in advance.

For details, please refer to ROHM Mounting specification

●Precautions Regarding Application Examples and External Circuits

1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2) You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

●Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

●Precaution for Storage / Transportation

1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

●Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

●Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

●Precaution for Foreign Exchange and Foreign Trade act

Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,

please consult with ROHM representative in case of export.

●Precaution Regarding Intellectual Property Rights

1) All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable

for infringement of any intellectual property rights or other damages arising from use of such information or data.:

2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the information contained in this document.

Notice - Rev.003

Daattaasshheeeett

●Other Precaution

1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

5) The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Notice - Rev.003


型号：	LM4565FVM
厂家：	ROHM
描述：	LM4565FVM是高电压增益、宽频带的低噪声运算放大器。等效输入噪声电压（5 HznV/ ）及总谐波失真（0.0002%）优异，因此是适用于音响设备、有源滤波器等用途的运算放大器。放大器运算放大器放大器电路有源滤波器
文件：	总20页 (文件大小：379K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

LM4565FVM [ROHM]

相关型号：

LM4565FVM-TR

LM4565FVT

LM4565FVT-E2

LM4570

LM4570LQ

LM4576-3.3BT

LM4576-3.3BT-LB02

LM4576-3.3BU

LM4576-3.3BU-TR

LM4576-3.3BUT&R

LM4576-5.0BT

LM4576-5.0BT-LB02