LTR18EZPF13R0 [ROHM]

Fixed Resistor, Metal Glaze/thick Film, 0.5W, 13ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0612, CHIP;


型号：	LTR18EZPF13R0
厂家：	ROHM
描述：	Fixed Resistor, Metal Glaze/thick Film, 0.5W, 13ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0612, CHIP 电阻器
文件：	总8页 (文件大小：871K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

High power chip resistors < Wide terminal type >

LTR series

Datasheet

●Features

1)High joint reliability with long side terminations.

2)Highest power ratings in their class.

3)Guaranteed anti-surge characteristic in all series.

4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.

5)Corresponds toAEC-Q200.

●Products list

Rated

Limiting Maximum

Operating

temperature

range

Size

Temperature Resistance

Part No.

power element overload

Resistance range

coefficient

tolerance

(70℃)

(W)

voltage voltage

(mm) (inch)

(V)

(ppm/ ℃)

±100

±200

±100

±200

±100

±200

±100

±200

(%)

(Ω)

(℃)

D( ±0.5%)

F( ±1%)

J( ±5%)

D( ±0.5%)

F( ±1%)

J( ±5%)

D( ±0.5%)

F( ±1%)

J( ±5%)

D( ±0.5%)

F( ±1%)

J( ±5%)

10≦R≦1M (E24/96series)

1≦R≦1M (E24series)

10≦R≦1M (E24/96series)

1≦R≦1M (E24series)

10≦R≦130k (E24series)

1≦R≦1M (E24series)

10≦R≦1M (E24series)

1≦R≦1M (E24series)

LTR10 2012 0805

LTR18 3216 1206

LTR50 5025 2010

LTR100 6432 2512

0.25

0.75

1.0

150

300

-55～ +155

200

400

-55～ +155

2.0

(E24series)

1≦R<1M

*E24 : Standard products, E96 : Customproducts.(Class Jis E24 series only)

Design and specifications are subject tochange without notice.

Carefully checkthe specification sheet supplied with the product before using or ordering it.

●Part Number Description

L T R

1 8

E Z P

1 0 5

Resistance

tolerance

Part No.

Size (mm [inch])

Packagingspecifications code

Nominal resistance

Resistance code, 3 or 4 digits.

10(2012[0805])

18(3216[1206])

50(5025[2010])

100(6432[2512])

Packaging Quantity

D(±0.5%)

Part No. Code

LTR10 EZP

LTR18 EZP

LTR50 UZP

LTR100 JZP

LTR

specifications / Reel

F(±1%)

Resistance

tolerance

Resistance

code

(High power

chip resistors

/ wide terminal

type)

J (±5%)

Paper tape

5,000

4 digits

3 digits

(4mmPitch)

D,F

：

Paper tape

5,000

(4mmPitch)

EX.)

1Ω=1R00 (±1%)

1R0 (±5%)

9.1Ω=9R10 (±1%)

9R0 (±5%)

Embossed tape

5,000

(4mmPitch)

Embossed tape

4,000

(4mmPitch)

10Ω=10R0 (±0.5%,± 1%)

100 (±5%)

1MΩ=1004 (±0.5%,± 1%)

105 (±5%)

www.rohm.com

1/4

2017.06 - Rev.H

LTR series

Datasheet

●Chip resistor dimensions and markings

There are three or four digits used for the calculation number

according to IEC code and "R" is used for the decimal point.

(Unit:mm)

Marking

Part No.

(mm)

2012

(inch)

0805

existence

LTR10

1.20±0.10

2.0±0.10

0.55±0.10

0.25±0.10

0.35±0.20

Yes

LTR18

LTR50

3216

5025

6432

1206

2010

2512

1.6±0.15

2.5±0.15

3.2±0.15

5.0±0.15

6.4±0.15

0.55±0.10

0.55±0.15

0.30±0.20

0.38±0.20

0.40±0.25

0.50±0.20

0.90±0.20

1.13±0.25

Yes

LTR100

●Land pattern example

(Unit:mm)

Dimensions

Part No.

LTR10

LTR18

LTR50

LTR100

0.50

0.60

0.75

0.83

2.70

2.90

3.35

3.69

2.00

3.20

5.00

6.40

1.10

1.15

1.30

1.43

www.rohm.com

2/4

2017.06 - Rev.H

LTR series

Datasheet

●Derating curve

When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.

■LTR10 / 18 / 50 / 100

●Characteristics

Guaranteed >

Resistor type

Test items

Test conditions

Resistance

See P.1

20℃

Variation of resistance

with temperature

See P.1

Measurement：+25/-55, +25/+125℃

Test voltage is the smaller one of ① or ②

①Rated voltage(current)×2.5， 2s

②Maximum overload voltage ※

Overload

±(2.0％＋0.1Ω)

Anew uniform coating of minimum

of 95%of the surface being

immersed and no soldering

damage.

Rosin-ethanol solution(25%weight)

Soldering condition：245±5℃

Duration of immersion：2.0±0.5s

Solderability

±(1.0％＋0.05Ω)

Soldering condition：260±5℃

Resistance to

soldering heat

No remarkable abnormalityon the appearance. Duration of immersion：10±1s

Rapid change of

temperature

±(1.0％＋0.05Ω)

±(3.0％＋0.1Ω)

Test temp：-55℃～+125℃ 5cycle

40℃，93％(Relative humidity)

Test time：1,000h

Damp heat, steadystate

Rated voltage(current),70℃

1.5h:ON－0.5h:OFF

Test time：1,000h

Endurance at 70℃

±(3.0％＋0.1Ω)

155℃

Test time：1,000h

Endurance

±(3.0％＋0.1Ω)

±(1.0％＋0.05Ω)

23±5℃ Immersion cleaning,

Solvent: 2-propanol

Resistance to solvent

±(1.0％＋0.05Ω)

Without mechanical damage such as breaks.

Bend strength of

the end face plating

Staticꢀelectric

characteristics

±(5.0％＋0.05Ω)

Compliance Standard(s) : IEC60115-8

※Maximum overload voltage (Test voltage)

JISC 5201-8

LTR10

300V

LTR18

400V

LTR50

400V

LTR100

400V

www.rohm.com

3/4

2017.06 - Rev.H

LTR series

Datasheet

●Tape dimensions

■Paper tape

(Unit : mm)

Part No.

LTR10

8.0±0.3

3.5±0.05 1.75±0.1 1.45±0.1

2.3±0.1

+0.1

-0.05

+0.15

3.5

LTR18

8.0±0.3

3.5±0.05 1.75±0.1 1.95

-0.05

Part No.

+0.1

LTR10 Φ1.5

LTR18 Φ1.5

4.0±0.1

2.0±0.05 MAX1.1

4.0±0.1

(Unit : mm)

■Embossed tape

Part No.

LTR50 12.0±0.3

LTR100 12.0±0.3

5.5±0.05 1.75±0.1

3.4±0.2

5.6±0.2

6.7±0.2

3.5±0.2

Part No.

+0.1

LTR50 Φ1.5

4.0±0.1

2.0±0.05 MAX1.1

LTR100 Φ1.5

4.0±0.1

●Reel dimensions

(Unit : mm)

Part No.

LTR10

LTR18

LTR50

LTR100

-1.5

+1.0

Φ180

Φ60

Φ13±0.2

www.rohm.com

4/4

2017.06 - Rev.H

Notice

Precaution on using ROHM Products

(Note 1)

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any

ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

CHINA

CLASSⅢ

CLASSⅣ

CLASSⅡb

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the

use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our

Products under any special or extraordinary environments or conditions (as exemplified below), your independent

verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in

the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PAA-E

Rev.003

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Notice-PAA-E

Rev.003

Daattaasshheeeett

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

Notice – WE

Rev.001

Datasheet

Buy

LTR100JZPD - Web Page

Distribution Inventory

Part Number

Package

LTR100JZPD

Unit Quantity

Minimum Package Quantity

Packing Type

Constitution Materials List

RoHS

Taping

inquiry

Yes

LTR18EZPF13R0 [ROHM]

相关型号：

LTR18EZPF13R3

LTR18EZPF1501

LTR18EZPF1502

LTR18EZPF1542

LTR18EZPF1543

LTR18EZPF1580

LTR18EZPF1582

LTR18EZPF15R0

LTR18EZPF15R8

LTR18EZPF1621

LTR18EZPF1623

LTR18EZPF1651